Aiwa CDC Z107 User Manual

CDC-Z107

SERVICE MANUAL

STEREO CAR CD RECEIVER

BASIC CD MECHANISM : TN-CCD1001-113J

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”

of CDC-Z107<YU>, (S/M Code No. 09-99B-422-4T1).

S/M Code No. 09-002-422-4R1

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully

the instructions below when servicing.

CAUTION

Use of controls or adjustments or performance of proce-

dures other than those specified herin may result in

hazardous radiation exposure.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER

EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS

NECESSARY TO CONFIRM LASER BEAM EMISSION.

BE SURE TO OBSERVE FROM A DISTANCE OF MORE

THAN 30cm FROM THE SURFACE OF THE OBJEC-

TIVE LENS ON THE OPTICAL PICK-UP BLOCK.

ATTENTION

L’utillisation de commandes, réglages ou procédures

autres que ceux spécifiés peut entraîner une dangereuse

exposition aux radiations.

ADVARSEL

Usynliglaserstålingvedåbning,nårsikkerhedsafbrydereer

ude af funktion. Undgå udsættelse for stråling.

Caution: Invisible laser radiation when

open and interlocks defeated avoid

exposure to beam.

Advarsel: Usynlig laserståling ved åbning,

nårsikkerhedsafbrydereerudeaffunktion.

Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1

LASER product.

The CLASS 1 LASER PRODUCT label is located on the

rear exterior.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saataa altistaa käyt-täjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

CLASS 1

KLASSE 1

LUOKAN 1

KLASS 1

LASER PRODUCT

LASER PRODUKT

LASER LAITE

VARNING!

LASER APPARAT

Om apparaten används på annat sätt än vad som

specificeras i denna bruksanvising, kan användaren

utsättas för osynling laserstrålning, som överskrider

gränsen för laserklass 1.

Precaution to replace Optical block

PICK-UP ASSY

P.C.B

(OPTIMA-720AIE)

Body or clothes electrostatic potential could

ruin laser diode in the optical block. Be sure

ground body and workbench, and use care

the clothes do not touch the diode.

1) After the connection, remove solder

shown in right figure.

- 3 -

ELETRICAL MAIN PARTS LIST

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

C210

C211

C212

C213

C214

87-016-669-080

87-010-498-040

87-010-180-080

87-010-992-080

87-016-669-080

C-CAP,S 0.1-25 K B

CAP,E 10-16 M 5L SRE

C-CER 1500P

CAP, CHIP 0.047

CHIP CAPACITOR,0.1-25

87-A20-446-010

87-A21-319-010

87-A21-488-040

8Z-KT1-622-010

87-A21-562-010

C-IC,LA9241ML

C-IC,LC78622NE

C-IC,LA6556

C-IC,LC75374E

IC,LA4743B

C215

C216

C217

C218

C219

87-010-178-080

87-A11-606-080

87-016-669-080

87-010-198-080

87-012-157-080

CHIP CAP 1000P

C-CAP,S 0.22-25 K B

CAP, CHIP 0.01 DM

CAP, CHIP 0.022

88-KT1-606-080

87-A21-535-030

87-A21-489-030

IC,PST994D

C-IC,LC72358N-9910

C-IC,LC75853NW

C-CAP,S 330P-50 CH

C220

C221

C222

C223

C224

87-010-184-080

87-010-322-080

87-010-492-040

87-010-067-040

87-010-553-040

CHIP CAPACITOR 3300P(K)

C-CAP,S 100P-50 CH

CAP,E 0.33-50 GAS

CAP,E 0.1-50 5L

TRANSISTOR

89-324-122-080

87-A30-289-040

87-A30-288-040

87-A30-287-040

87-026-235-080

TR,2SC2412K

C-TR,2SA1037AK(R)

C-TR,DTC114YKA

C-TR,DTC114TKA

CHIP-TR,DTC114EK

CAP,E 47-16 GAS

C225

C226

C227

C228

C229

87-010-805-080

87-010-497-040

87-010-555-040

87-016-669-080

87-010-498-040

C-CAP,S 1-16 Z F

CAP,E 4.7-35 GAS

CAP,E 100-10 GAS

CHIP CAPACITOR,0.1-25

CAP,E 10-16 GAS

87-026-210-080

87-A30-299-080

87-A30-282-040

87-A30-168-010

89-211-821-080

CHIP-TR,DTC144EK

TR,2SB1326

C-TR,DTA114TKA

TR,2SB1566F

C230

C231

C232

C233

C234

87-016-669-080

87-010-555-040

87-016-669-080

87-010-555-040

87-010-193-080

CHIP CAPACITOR,0.1-25

CAP,E 100-10 GAS

CHIP CAPACITOR,0.1-25

CAP,E 100-10 GAS

CHIP CAPACITOR,0.033

CHIP-TR 2SB1182Q

89-423-953-010

87-A30-301-080

87-A30-449-040

TR,2SD2395F

TR,2SD1862

C-TR,DTA123YKA

C235

C236

C237

C238

C240

87-010-992-080

87-010-067-040

87-010-553-040

87-010-197-080

87-016-669-080

CAP, CHIP 0.047

CAP,E 0.1-50 5L

CAP,E 47-16 GAS

CAP, CHIP 0.01 DM

C-CAP,S 0.1-25 K B

DIODE

87-A40-250-080

87-001-783-080

87-020-331-080

87-A40-624-080

87-A40-523-080

CHIP-DIODE,DAN217

DIODE,1N4002

C-DIODE,DAN202K

ZENER,MTZJ10A

ZENER,MTZJ9.1B

C250

C251

C252

C253

C254

87-016-669-080

87-010-555-040

87-016-669-080

CHIP CAPACITOR,0.1-25

CAP,E 100-10 GAS

CHIP CAPACITOR,0.1-25

87-070-136-080

87-017-932-080

87-A40-798-010

ZENER,MTZJ5.1B

ZENER,MTJ6.2B

DIODE,1N5402 (3A/200V)

C256

C258

C259

C261

C262

87-010-186-080

87-010-150-080

87-010-316-080

87-012-156-080

87-016-669-080

CAP,CHIP 4700P

C-CAP,S 6P-50 D CH

C-CAP,S 33P-50 CH

C-CAP,S 220P-50 CH

CHIP CAPACITOR,0.1-25

MAIN C.B

C101

C102

C103

C106

C107

87-010-178-080

87-010-197-080

87-010-495-040

87-010-322-080

87-010-552-040

CHIP CAP 1000P

CAP, CHIP 0.01 DM

CAP,E 2.2-50 GAS

C-CAP,S 100P-50 CH

CAP,E 22-16 GAS

C263

C264

C265

C266

C267

87-010-555-040

87-016-669-080

87-010-498-040

CAP,E 100-10 GAS

CHIP CAPACITOR,0.1-25

CAP,E 10-16 GAS

C108

C109

C110

C111

C112

87-010-322-080

87-010-553-040

87-010-198-080

87-010-553-040

87-010-185-080

C-CAP,S 100P-50 CH

CAP,E 47-16 GAS

CAP, CHIP 0.022

CAP,E 47-16 GAS

C-CAP,S 3900P-50 B

C268

C269

C270

C271

C272

87-010-498-040

87-010-180-080

87-010-154-080

CAP,E 10-16 GAS

C-CER 1500P

CAP CHIP 10P

C113

C114

C115

C116

C131

87-010-197-080

87-010-196-080

87-012-365-080

CAP, CHIP 0.01 DM

CHIP CAPACITOR,0.1-25

C-CAP,S 0.027-25VBK

C273

C274

C280

C281

C282

87-010-494-040

87-A10-189-040

87-010-555-040

87-016-669-080

CAP,E 1-50 GAS

CAP,E 220-10

CAP,E 100-10 GAS

CHIP CAPACITOR,0.1-25

C132

C133

C134

C161

C171

87-012-365-080

87-012-358-080

87-010-196-080

87-010-197-080

C-CAP,S 0.027-25VBK

C-CAP,S 0.47-10 F Z

CHIP CAPACITOR,0.1-25

CAP, CHIP 0.01 DM

C301

C302

C303

C304

C305

87-010-498-040

87-010-494-040

87-010-184-080

CAP,E 10-16 GAS

CAP,E 1-50 GAS

CHIP CAPACITOR 3300P(K)

C173

C201

C202

C203

C204

87-010-322-080

87-010-553-040

87-010-178-080

87-016-669-080

C-CAP,S 100P-50 J CH GRM

CAP,E 47-16 GAS

CHIP CAP 1000P

C-CAP,S 0.1-25 K B

C306

C307

C308

C309

C310

87-010-184-080

87-010-198-080

87-010-498-040

CHIP CAPACITOR 3300P(K)

CAP, CHIP 0.022

CAP,E 10-16 GAS

C205

C206

C207

C208

C209

87-A11-606-080

87-010-492-040

87-010-195-080

87-010-176-080

87-010-992-080

C-CAP,S 0.22-25 K B

CAP,E 0.33-50 GAS

C-CAP,S 0.068-25 Z F C2012

C-CAP,S 680P-50 J SL

C-CAP,S 0.047-25 K B MK212

C311

C312

C313

C314

C315

87-A11-177-080

87-010-498-040

C-CAP,S 0.15-16 K B

CAP,E 10-16 GAS

- 4 -

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

C316

C321

C322

C323

C324

87-010-498-040

87-010-196-080

87-010-555-040

87-010-196-080

87-010-498-040

CAP,E 10-16 GAS

L831

L881

R241

R242

SW702

87-003-143-080

8Z-KT1-615-010

87-022-371-080

87-A91-152-010

COIL,4.7UH K LAL02

CHIP CAPACITOR,0.1-25

CAP,E 100-10 M 5L SRE

CHIP CAPACITOR,0.1-25

CAP,E 10-16 GAS

FLTR,AMORPHOUS -CHOKE

C-RES,S 330K-1/10W F

SW,SL 1-1-2 SSSS212-11-A

C351

C352

C353

C354

C361

87-010-494-040

87-012-358-080

CAP,E 1-50 GAS

C-CAP,S 0.47-10 F Z

TU101

X201

X701

8A-KC8-621-010

81-592-641-010

87-A70-175-010

TU UNIT, FAE347-A12

VIB,CER 16.93MHZ

VIB,XTAL 4.5MHZ AT-49

FRONT C.B

C362

C363

C364

C365

C366

87-012-358-080

87-010-175-080

C-CAP,S 0.47-10 F Z

CAP 560P

C901

C902

C903

C904

C905

87-010-805-080

87-010-194-080

87-010-177-080

87-010-196-080

CAP, S 1-16

CAP, CHIP 0.047

C-CAP,S 820P-50 SL

CHIP CAPACITOR,0.1-25

CAP 560P

C367

C368

C453

C454

C457

87-010-175-080

87-010-498-040

87-012-140-080

CAP 560P

CAP,E 10-16 GAS

CAP 470P

LCD901

LED951

LED952

LED953

LED961

8A-KCG-610-010

87-A91-052-080

87-A40-813-040

LCD,AKC-16-17

LED,SEL6227S RED

C-LED,SEC1E01C BLUE

C458

C461

C511

C512

C513

87-012-140-080

87-005-902-080

8A-KC7-623-000

87-010-196-080

CAP 470P

C-COIL,S 4.7UH K LK2125

CAP,E 2200U-16 BT(125C)

CHIP CAPACITOR,0.1-25

LED962

LED963

PL901

PL902

SW901

87-A40-813-040

8Z-KT1-641-010

87-036-251-080

C-LED,SEC1E01C BLUE

LAMP,T-3

SW,T CT 6X3.5 160

C514

C515

C516

C517

C519

87-010-553-040

87-010-494-040

87-010-178-080

87-010-494-040

CAP,E 47-16 M 5L SRE

CAP,E 1-50 GAS

CHIP CAP 1000P

CAP,E 1-50 M 5L SRE

SW902

SW903

SW904

SW905

SW906

87-036-251-080

SW,T CT 6X3.5 160

C551

C590

C611

C612

C613

87-010-553-040

87-010-178-080

87-010-553-040

87-010-198-080

87-016-044-040

CAP,E 47-16 GAS

CHIP CAP 1000P

CAP,E 47-16 GAS

CAP, CHIP 0.022

CAP,E 100-16 GAS

SW907

SW908

SW910

SW911

SW913

87-036-251-080

SW,T CT 6X3.5 160

C621

C622

C641

C642

C671

87-010-553-040

87-010-196-080

87-010-198-080

CAP,E 47-16 GAS

CHIP CAPACITOR,0.1-25

CAP, CHIP 0.022

SW914

SW915

SW916

SW917

SW918

87-036-251-080

SW,T CT 6X3.5 160

C672

C673

C674

C681

C682

87-010-555-040

87-010-553-040

87-010-198-080

87-010-553-040

87-010-198-080

CAP,E 100-10 GAS

CAP,E 47-16 GAS

CAP, CHIP 0.022

CAP,E 47-16 GAS

CAP, CHIP 0.022

SW921

SW971

87-A91-597-010

87-036-251-080

SW,RTRY SIM-026MT

SW,T CT 6X3.5 160

AUX C.B

C701

C702

C706

C711

C712

87-010-315-080

87-010-314-080

87-010-497-040

87-010-322-080

C-CAP,S 27P-50 CH

C-CAP,S 22P-50V

CAP,E 4.7-35 GAS

C-CAP,S 100P-50 CH

CON831

J831

87-A60-912-010

85-HRL-623-010

CONN,3P V 1MSA-9202B-1

JACK,3.5 ST BLK

C761

C763

C771

C831

C832

87-010-555-040

87-010-196-080

87-012-156-080

87-010-494-040

CAP,E 100-10 GAS

CHIP CAPACITOR,0.1-25

C-CAP,S 220P-50 J CH GRM

CAP,E 1-50 GAS

C835

C836

C881

C882

C883

87-010-182-010

87-010-182-080

C-CAP,S 2200P-50 K B C2012

C-CAP,S 2200P-50 B

C884

87-010-182-080

87-A60-859-010

87-A60-860-010

8Z-KT1-611-010

8Z-KC1-621-010

C-CAP,S 2200P-50 B

CONN,12P TKC-F12X-K1

CONN,14P TKC-F14X-K1

CONN,16P CAM-B51

FUSE,15A 32V

CON201

CON202

CON881

F881

J101

J451

L101

L102

L671

8Z-KT1-614-010

87-A61-225-010

87-003-143-080

8Z-KT1-619-010

87-003-149-080

ANT,AW-002

JACK,PIN 2P XR-401

COIL 4.7 UH

COIL,68MH K7-D

COIL,47UH

- 5 -

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8

Figure

Resistor Code

Value of resistor

Chip resistor

Dimensions (mm)

: A

Symbol

Wattage

1/16W

1/10W

Type

Tolerance

Resistor Code

104

Form

1005

1608

2125

1.0

0.5 0.35

1.6

0.8 0.45

1.25 0.45

1.6 0.55

108

118

128

3.2

1/8W

3216

TRANSISTOR ILLUSTRATION

E C B

B C E

2SA1037

2SC2412

2SB1326

2SD1862

2SB1182

2SB1566

2SD2395

DTA114TKA

DTA123YKA

DTC114EK

DTC114YKA

DTC114TKA

DTC144EK

- 6 -

WIRING - 1 (MAIN: 1 / 2)

- 7 -

WIRING - 1 (MAIN: 1 / 2)

- 8 -

SCHEMATIC DIAGRAM - 1 (MAIN: 1 / 2)

- 9 -

SCHEMATIC DIAGRAM - 2 (MAIN: 2 / 2)

- 10 -

WIRING - 2 (FRONT)

- 11 -

SCHEMATIC DIAGRAM - 3 (FRONT)

- 12 -

IC BLOCK DIAGRAM

IC,LA4743B

IC,LA6556

- 13 -

LCD DIAGRAM

- 14 -

VOLTAGE CHART

IC, LC72358N-9910

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

2.42

AUX (V)

2.45

2.47

2.35

2.28

2 ~ 6

4.85

0.05

0.20

0.22

4.84

0.05

0.21

4.87

4.91

4.90

0.15

0.70

0.75

0.03

4.87

0.03

0.10

0.21

0.10

0.24

4.83

4.57

4.54

15 ~ 16

4.78

4.72

19 ~ 30

4.85

4.98

5.00

4.79

4.85

4.91

32 ~ 38

4.84

4.83

4.85

4.89

4.72

4.74

4.78

4.72

4.73

4.74

4.77

4.79

4.80

4.84

4.46

4.49

4.44

4.45

4.52

4.84

2.00

4.46

4.89

4.86

4.90

4.89

4.87

4.94

4.75 / 0

4.77 / 0

4.90

4.70 / 4.75

3.50

4.78 / 0

4.80 / 0

4.87

4.82 / 4.78

3.40

4.78 / 0

4.80 / 0

4.90

4.82 / 4.78

3.44

4.75 / 0

4.77 / 0

4.86

4.70 / 4.75

3.44

4.75 / 0

4.77 / 0

4.86

4.70 / 4.75

3.44

4.75 / 0

4.84

4.72 / 4.75

3.41

58 ~ 60

4.86

4.89

4.88

4.87

4.93

4.87

62 ~ 64

3.31

4.94

3.32

4.96

3.31

4.78

4.63

3.32

4.78

4.62

3.32

4.87

4.61

3.31

4.79

4.62

- 15 -

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

4.76

0.58

2.51

AM(V)

4.76

0.57

2.51

CD (V)

AUX (V)

4.79

0.59

2.52

4.94

4.95

4.87

71 ~ 72

4.98

4.97

4.80

2.34

0.01

4.91

4.84

2.31

0.03

2.45

0.08

1.04

0.08

1.04

1.05

2.53

2.52

2.45

2.46

2.50

2.47

IC, LA4743B

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

AUX (V)

1 ~ 2

2.75

4.76

2.74

14.38

2.75

2.74

4.82

2.74

14.38

2.74

4.83

2.75

14.38

2.74

4.84

2.75

14.38

2.74

14.40

2.68

13.17

3.04

3.09

2.73

13.15

3.07

3.11

2.73

13.16

3.07

3.11

2.74

13.16

3.08

3.11

24 ~ 25

3.09

3.04

2.29

2.71

3.11

3.07

2.40

2.74

3.11

3.07

2.41

2.74

3.11

3.08

2.40

2.74

2.73

14.38

2.76

4.54

2.72

2.74

14.38

2.73

4.55

2.76

2.74

14.38

2.73

4.58

2.76

2.74

14.35

2.73

4.56

2.77

14.40

- 16 -

IC, LA9241ML

PIN NO.

1 ~ 2

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

2.50

2.53

2.49

2.51

2.52

2.51

2.50

2.51

2.50

2.61

2.52

2.42

2.52

2.53

2.51

AUX (V)

5 ~ 7

9 ~ 12

22 ~ 23

24 ~ 25

26 ~ 28

2.47

2.63

2.37

31 ~ 33

4.93

1.0

37 ~ 39

0.50

2.29

2.40

2.41

2.50

2.51

2.41

45 ~ 46

48 ~ 49

2.41

4.80

52 ~ 53

4.84

4.93

2.51

2.39

57 ~ 58

- 17 -

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

AUX (V)

2.22

3.71

0.19

4.91

IC, LA6556

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

AUX (V)

1 ~ 2

4 ~ 5

8.44

3.70

4.06

3.76

4.05

3.86

3.88

3.60

4.20

8.45

2.38

16 ~ 17

18 ~ 22

2.51

2.45

2.51

7.85

4.98

2.51

8.44

2.51

2.43

4.91

24 ~ 25

30 ~ 32

34 ~ 35

- 18 -

IC, LC78622NE

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

0.05

AUX (V)

1.55

1.77

4.69

0.33

2.49

2.39

0.50

13 ~ 17

4.92

19 ~ 20

2.35

4.93

22 ~ 23

24 ~ 30

2.47

32 ~ 36

2.03

38 ~ 39

2.03

4.96

4.92

4.79

1.75

1.85

0.10

0.02

0.11

2.47

2.46

2.0

0.04

4.80

4.88

- 19 -

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

AUX (V)

1.93

2.34

62 ~ 64

TU UNIT, FAE347-A12

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

AM(V)

CD (V)

AUX (V)

1 ~ 2

0.02

6.89

6.93

3.42

7 ~ 8

7.95

7.85

10 ~ 11

7.27

7.58

3.41

7.31

7.61

3.42

7.49

3.42

7.46

3.42

3.41

3.36

3.44

3.41

3.39

3.42

18 ~ 19

0.01

5.74

4.55

1.07

4.07

7.58

0.01

3.66

4.56

0.63

1.21

7.50

0.03

0.43

4.56

0.05

4.01

7.61

2.05

4.54

0.04

1.21

7.46

0.03

- 20 -

IC, LC75374E

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

3.94

3.98

4.00

3.99

AM(V)

3.93

3.98

4.00

3.99

CD (V)

3.96

4.00

4.02

4.01

AUX (V)

3.96

4.01

4.02

3.99

4 ~ 6

8 ~ 9

3.98

4.01

3.99

4.02

4.01

3.98

4.01

3.99

4.01

4.00

4.03

4.01

4.04

4.03

3.99

4.01

3.99

4.01

15 ~ 18

4.01

4.02

4.01

3.98

4.01

3.98

4.03

4.04

4.03

4.00

4.01

3.98

4.01

3.98

20 ~ 21

25 ~ 26

4.02

4.01

4.00

3.91

4.02

4.00

3.99

4.01

3.99

3.91

4.01

3.99

4.04

4.03

4.02

3.93

4.04

4.02

3.99

4.01

4.00

3.98

3.93

4.02

4.00

30 ~ 31

37 ~ 38

4.00

7.64

4.00

3.99

7.63

3.99

4.02

7.68

4.02

4.01

4.00

7.64

4.00

3.99

4.00

4.03

3.99

4.02

4.05

3.99

4.01

- 21 -

IC, LC75853NW

PIN NO.

BU (V)

BU+ACC (V)

FM (V)

4.84

AM(V)

4.83

CD (V)

4.86

AUX (V)

4.85

2.50

4.96

2.50

4.96

2.47

2.49

2.48

4.95

2.47

2.46

2.47

2.46

2.47

2.46

2.47

2.46

2.47

2.46

4.92

4.93

4.92

2.48

2.47

2.48

2.47

2.48

2.47

2.48

2.47

2.48

2.47

2.48

2.47

2.48

4.93

2.48

2.47

2.48

2.47

2.46

4.91

7 ~ 10

11 ~ 12

15 ~ 16

18 ~ 19

20 ~ 23

24 ~ 25

26 ~ 29

31 ~ 32

33 ~ 40

47 ~ 49

50 ~ 55

4.99

3.33

1.67

4.99

3.33

1.67

4.95

3.32

1.67

4.92

3.29

1.65

4.93

3.30

1.66

4.91

3.28

1.65

3.91

4.96

3.91

4.96

3.88

4.92

0.25

0.04

3.88

4.86

0.24

0.20

0.03

3.88

4.88

0.77

0.67

0.18

3.87

4.86

0.24

0.03

- 22 -

IC DESCRIPTION

IC, LC72358N-9910

Pin No.

Pin Name

I/O

Description

2 ~ 3

XIN

System clock oscillator input.

Not connected.

E-VOL DO

E-VOL CLO

E-VOL CE

LCD DI

Data output for electric volume.

Clock output for electric volume.

CE output for electric volume.

LCD driver data signal input.

LCD driver data signal output.

LCD driver clock signal output.

LCD driver CE signal output.

Sub-code Q input terminal.

Command output terminal for DSP.

LCD DO

LCD CLO

LCD CE

SQ OUT

COIN

Transfer-out clock for command output or output terminal for Sub-code transfer-in

clock from SQ OUT.

CQCK

SD/ST

Stereo signal input when receiving. Hi=MONO, Low=ST FM reception.

Channel detection signal input when FM/AM seeking. Hi=detect channel

LOC/DX switching output when in the radio seek mode. Hi=LOC, Low=DX

IF count signal request output.

LOC/DX

IF REQ

BAND

FM/AM power switch output. Hi=AM, Low=FM

Radio power switch output. Hi=Radio mode

Not connected.

TU ON

19 ~ 21

22 ~ 23

24 ~ 26

27 ~ 30

KS4 ~ KS3

KS2 ~ KS0

K3 ~ K0

VDD

Initial setting diode matrix output(Not used).

Initial setting diode matrix output.

Initial setting diode matrix input.

Power supply.

Not connected.

LM+

Loading motor control terminal.

LM-

Loading motor control terminal.

FEM+

Thread motor control terminal.

FEM-

Thread motor control terminal.

RW disc control. Normal set to "Hi". Hi=NORMAL DISC, Low=RW DISC

RW disc control. Normal set to "Lo". Hi=Disable playback even though

CD power switch output. Hi=CD mode RW port is low

Audio mute signal output.

LP UP

CD ON

A-MUTE

POWER CONT

ST-BY MUTE

POWER MUTE

BEEP

Power control signal output.

ST-BY mute signal output.

Power mute signal output.

BEEP output(3 kHz, 50 ms).

DFP IN

DRF

Front panel detection.

"Detect RF" RF level detection input. Pulled up when not used.

Sub-code Q output standby input terminal.

WRQ

- 23 -

Pin No.

Pin Name

RWC

I/O

Description

Read / write control output terminal.

DSP reset output terminal.

CD RES

SW3

Disc detection / chuck or release disc detection.

12 cm disc detection / 12 cm disc ejection end detection.

Leading motor start detection.

Rotary encoder input 2.

SW2

SW1

R-ENCOD2

R-ENCOD1

LCD-DI

REMOTE IN

LED

Rotary encoder input 1.

LCD driver data signal input.

Remote controller input. Pulled up when not used.

Security LED flashing output. H: No light on, L: Light on.

Not connected.

58 ~ 60

INSIDE

TEST

Pick up inner track position detection.

CD test mode. Pulled down when not used.

Not connected.

L IND

PH.MUTE

RESET

HOLD

SNS

Voltage input for level indecator. Pulled down when not used.

External mute control. Low=-20dB mute. Pulled up when not used.

System reset. Low= system reset.

ACC (accessory power) ON/ OFF input. OFF=fault mode.

Backup detection.

Not connected.

IF count signal input (FM / AM).

Not used.

EO3

SUBPD

VDD

Not used.

Power supply.

AM OSC

FM OSC

VSS

AM channel transmission input.

FM channel transmission input.

Connected to GND.

EO2

Not used.

EO1

Error out from charge pump (for FM / AM).

Not connected.

XOUT

System clock oscillator output.

- 24 -

IC, LA9241ML

Pin No.

Pin Name

FIN2

FIN1

I/O

Description

For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF

signal and subtraction from it create an EF signal.

For the connection of the pickup photodiode.

For the connection of the pickup photodiode. Subtraction from the F pin creates a TE

signal.

For the connection of the pickup photodiode.

Inputs the DC components in the TE signal.

For the connection of a resistor which sets the gain of the TE signal between this pin

and the TE pin.

TE-

TESI

SCI

TD-

TE signal output.

TES (track error sense) comparator input. The signal is passed through a BPF.

Shock detection input.

Sets the time constant for the tracking gain.

TA amp output.

Composes the tracking phase compensation constant between the TD and VR pins.

Sets the tracking phase compensation.

Sets the amplitude of the tracking jump signal (kick pulses).

Tracking control signal output.

Focusing control signal output.

FD-

Composes the focusing phase compensation constant between the FD and FA pins.

FE signal output.

FA-

For the connection of a resistor whichs sets the gain of the FE signal between this pin

and the TE pin.

FE-

A-GND

Ground of analog signals.

Single-ended output of the signals input to the CV+ and CV- pins.

Spindle amp input.

SPI

SPG

SP-

For the connection of a resistor which sets the gain in the spindle 12cm mode.

For the connection of the spindle phase compensation constant with the SPD pin.

Spindle control signal output.

SPD

SLEQ

SLD

SL-

For the connection of sled phase compensation constant.

Sled control signal output.

Sled feed signal input from the microprocessor

SL+

JP-

Tracking signal input from the DSP.

JP+

TGL

TOFF

TES

Tracking gain control signal input from the DSP. Low gain when TGL is "H".

Tracking off control signal input from the DSP. Off when TOFF is "H".

Outputs the TES signal to the DSP.

- 25 -

Pin No.

Pin Name

HFL

I/O

Description

The HFL (high frequency level) signal is used to judge whether the main beam is

positioned on the pit or on the mirror.

SLOF

CV-

Sled servo off control input.

CLV error signal input from the DSP.

CV+

RFSM

RF output.

Sets the RF gain and the EFM singal's 3T compensation constant togther with the

RFSM pin.

RFS-

SLC

The SLC (slice level control) signal is output to control the DSP's data slice level of the

RF waveform.

SL1

D-GND

FSC

TBC

Input to control the DSP's data slice level.

Ground of digital signals.

Output for the focus search smoothing capacitor.

The TBC (tracking balance control) signal sets the EF balance variation range.

Not connected.

DEF

CLK

Disc defect detection output.

Reference clock input. 4.23 MHz is input from the DSP.

Microprocessor command clock input.

DAT

Microprocessor command data input.

Microprocessor chip enable input.

DRF

DRF (detect RF) is an output to detect the RF level.

The FSS (focus search select) signal switches the focus search modes (+/-search /

+search with respect to the reference voltage). (Not connected)

VCC of servo and digital circuits.

FSS

VCC2

REF1

For the connection of bypass capacitor for the reference voltage.

Reference voltage output.

LF2

Sets the time constant for disc defect detection.

For the connection of a capacitor to hold the RF signal peak.

For the connection of a capacitor to hold the RF signal bottom.

APC circuit output.

PH1

BH1

LDD

LDS

VCC1

APC circuit input.

VCC of RF signal circuits.

- 26 -

IC, LC78622NE

Pin No.

Pin Name

DEFI

TAI

I/O

Description

Defect detection signal (DEF) input. (Must be connected to 0V when unused.)

For PLL/Test input. A pull-down resistor is built-in. (Must be connected to 0V.)

External VCO control phase comparator output.

Intetnal VCO ground. (Must be connected to 0V.)

PDO output current adjustment resistor connection.

Internal VCO power supply.

PDO

VVSS

ISET

VVDD

VCO frequency range adjustment.

VSS

Digital system ground. (Must be connected to 0V.)

Slice level control EFM signal output.

EFMO

EFMIN

TEST2

CLV+

CLV-

Slice level control EFM signal input.

Test input. A pull-down resistor is built-in. (Must be connected to 0V.)

Disc motor control output. Can be set to three-value output by microprocessor

command.

Rough servo/phase control automatic switching monitor output. Outputs a high level

during rough servo a low level.

V/P

HFL

TES

TOFF

TGL

JP+

Track detection signal input. This is a Schmitt input.

Tracking error signal input. This is a Schmitt input.

Tracking off output.

Tracking gain switching output. Increase the gain when low.

Track jump output. Three value output is also possible when specified by0

microprocessor command.

JP-

PCK

EFM data playback clock monitor. Output 4.3218 MHz when the phase is locked.

Synchronization signal detection output. Output a high level when the synchronization

signal detected from the EFM signal and the internaly generated synchronization signal

range.

FSEQ

VDD

Digital system power supply.

24 ~ 28

CONT1 ~ 5

I/O

General purpose input/ output pin1 ~ 5.

De-emphasis monitor. A high level indicates playback of a De-emphasis disk./ General

General purpose input/ output pin6.

EMPH/CONT6

C2F

C2 flag output.

DOUT

TEST3

TEST4

Digital output.

Test input. A pull-down resistor is built-in. (Must be connected to 0V.)

General purpose input/ output command identifying. A pull-down resistor is built-in.

"H": Control possible only for the general purpose input/ output port command.

"L": Control possible for all commands.

PCCL

MUTEL/CONT7

LVDD

Left channel mute output./ General purpose input/ output pin.

Left channel power supply.

LCHO

Left channel output.

LVSS

Left channel groud. (Must be connected to 0V.)

- 27 -

Pin No.

Pin Name

RVSS

I/O

Description

Right channel ground. (Must be connected to 0V.)

Right channel output.

RCHO

RVDD

MUTER/CONT8

XVDD

XOUT

Right channe power supply.

Right channel mute output./ General purpose input/ output.

Crystal oscillator power supply.

Connections for a 16.9344 MHz crystal oscillator element.

XIN

XVSS

Crystal oscillator ground. (Must be connected to 0V.)

Subcode clock synchronization signal output.

SBSY

EFLG

C1, C2, sigle an double error correction monitor.

Subcode P, Q, R, S, T, U and W output.

Subcode frame synchronization signal output. This signal falls when the subcode are

in standby stase.

SFSY

SBCK

FSX

Subcode readout clock input. This is a Schmitt input.

Output pin for the 7.35 kHZ synchronization signal divided from the crystal oscillator.

Subcode Q output standby output.

WRQ

RWC

Read/write control input. This is a Schmitt input.

Subcode Q output.

SQOUT

COIN

Command input pin from control microprocessor.

Input for both the command input acquisition clock and the SQOUT pin subcode

readout clock input pin. This is Schmitt input.

Reset input. This pin must be set low briefly after power is first applied.

Test output. Leave open. (Normally output a low level.)

16.9344 MHz output.

CQCK

RES

TST11

16M

4.2M

4.2336 MHz output.

TEST5

Test input. A pull-down resistor is built-in. (Must be connected to 0V.)

Chip seledt input. A pull-down resistor is built-in.

(Must be connected to 0V if not controlled.)

TEST1

Test input. No pull-down resistor. (Must be connected to 0V.)

- 28 -

IC, LC75374E

Pin No.

Pin Name

RVRIN

I/O

Description

4dB volume control input. Must be driven at a low impedance.

RCOM

–

1dB volume control common pin.

For the connection of capacitors that compensate for bass and treble in the tone control

circuits.

3 ~ 5

RT1 ~ RT3

–

A high-frequency compensation capacitors must be connected between T1 and T2.

A low-frequency compensation capacitors must be connected between T2 and T3.

RTOUT

RSIN

Tone control output.

Super bass input. Must be driven at a low impedance.

Connected to VSS.

–

Not used.

10 ~ 11

RSB1 ~ RSB2

RFIN

For the connection of RCH super bass compensation capacitors.

Fader input. Must be driven at a low impedance.

RFOUT

RROUT

VSS

–

Fader outputs. The front and rear sides can be attenuated independently.

Ground.

Serial data and clock inputs for control.

Chip enable. Data is written in the internal latch when the chip enable signal goes "L"

from "H", and each analog switch is activated. Data transfer is enabled at "H".

–

Generates a 1/2VDD power source. A capacitor must be connected between VREF and

VSS as a troubleshooting against power ripples.

VREF

LROUT

LFOUT

LFIN

Fader outputs. The frount and rear sides can be attenuated independently.

–

Fader input. Must be driven at a low impedance.

For the connection of LCH super bass compensation capacitors.

Not used.

23 ~ 24

LSB2 ~ LSB1

Connected to VSS.

LSIN

Super bass input. Must be driven at a low impedance.

Tone control output.

LTOUT

For the connection of capacitors that compensate for bass and treble in the tone control

circuit.

29 ~ 31

LT3 ~ LT1

–

A high-frequency compensation capacitors must be connected between T1 and T2.

A low-frequency compensation capacitors must be connected between T2 and T3.

LCOM

LVRIN

LSELO

AUX(L)

CD(L)

TUN(L)

TP(L)

–

1dB volume control common pin.

4dB volume control input. Must be driven at a low impedance.

Input selector output pin.

Signal input pins.

VDD

–

Power supply.

- 29 -

Pin No.

Pin Name

TP(R)

I/O

Description

TUN(R)

CD(R)

Signal input pins.

AUX(R)

RSELO

Input selector output pin.

IC, LC75853NW

Pin No.

1 ~ 40

Pin Name

S1 ~ S40

I/O

Description

LCD segment output.

LCD command driver outputs.

Key scan outputs.

41 ~ 43

44 ~ 49

50 ~ 54

COM1~ COM3

KS1 ~ KS6

KI1 ~ KI5

TEST

Key scan inputs. These pins have build-in pull-down resistor.

Test pin. (Connected to GND.)

VDD

Power supply.

Used for applying the LCD drive 2/3 bias voltage externally. (Must be connected to

VDD2 when a 1/2 bias drive scheme is used.)

Used for applying the LCD drive 1/3 bias voltage externally. (Must be connected to

VDD1 when a 1/2 bias drive scheme is used.

Power supply. (Connected to GND.)

VDD1

VDD2

VSS

OSC

I/O

Resistor and capacitor are attached externally form an oscillator circuit.

Serial data interface pin; output data.

Serial data interface pin; chip enable.

Serial data interface pin; synchronization.

Serial data interface pin; data transferred.

- 30 -

CD TEST MODE

Caution when servicing

(1) How to use extension jig.

1-1 How to Activate CD Test Mode

1) Connect 62 pin (test) of IC701 (LC72358N-9910) on

MAIN C.B to the 31 pin (VDD) by cable.

Correct between MAIN C.B. and CD mechanisms by extension jigs when checking CD mechanism

(TN-CCD1001-113J) operation.

(Refer to the following figure.)

2) Connect wire of ACC (red) and BACKUP (yellow) of power supply/speaker connector to DC+12V,

then connect Ground (black) to -.

When CD test mode is started, all displays will be lighted as shown in the following figure.

1-2 How to cancel CD Test Mode

1) Disconnect the cable of 62 pin (test) and 31 pin (VDD) of the MAIN C.B

IC701 (LC72358N-9910) and switch on the power.

Parts Description

AKC-JIG

Parts Number

SV-J00-075-010

1-3 CD Test Mode Functions

MODE

Keys to operate

Display

Operations

Contents

Start Mode

All lightented

•Start TEST MODE

Search Mode RANDOM

TOC

READING

• Continual Focus Search

(The pickup lens respeats the

full-swing up-down motion)

*NOTE 1

•Confirm APC circuit

•Laser current measurement

•Confirm focus error waveform

Play Mode

REP 1

INT

TRACK No.

• Normal Play Back

•Focus servo

• Traking servo

•CLV servo

Playing Time Indica- • Focus search is contiuned if

tion Revel/Ing

Indication

Track no. & Playing

Time Indication

TOC cannot be read

•

Sled servo

Traverse

Mode

• Pause Status

•Traking servo OFF

Thread Mode

All lightened

• Pick up Move to outer most track

• Pick up Move to inner most track

• Step 1 : For CD/CD-R

•Thread servo

•Confirm mechanism operation

•Step 1 to 3 are cyclic

Gain Switch

All lightened

(Preset Button)

• Step 2 : For CD-R RF Gain is up

against Step 1

•“Error 03” is indicated if the Disc

does not Step 1 match.

• Step 3 : For CD-R Laser Power Up

against Step 2

•

Do not insert a Disc when confirming Search Mode

Press PWR button when cancelling Search Mode. Test Mode will be restored when PWR button is

pressed once again.

•

Insert the “Test Disc” when operating all modes except search mode.

* NOTE 1

: There are CD operations are disable owing to the protection circuit being operated when heat builds up in the driver IC

if the focus search is operated continually for more than 10 minutes. In cases, the power supply should be switched off

for 10 minutes until heat has been reduced and then re-started.

- 31 -

MECHANICAL EXPLODED VIEW 1 / 1

P.C.B

PANEL,

HT-SINK 34

H2-AC

TN-CCD1001

-113J

HT-SINK

CHAS,FRONT

-AC17

P.C.B

- 32 -

MECHANICAL PARTS LIST 1 / 1

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

1 8A-KC7-005-010

2 8A-KC7-020-010

3 8A-KC7-220-010

4 8A-KCH-003-010

5 8A-KCF-022-010

KNOB,RTRY -AC

RING,RTRY -AC

SPR-C,ROTARY -AC

WINDOW,LCD Z107

WINDOW,SIDE R -AC15

26 8Z-KT1-236-010

27 8A-KCH-202-010

28 8A-KCH-219-010

29 8A-KCH-020-010

30 8Z-KC1-231-010

CAP,LAMP BLU

HLDR,PWB -AC17

COVER, DUST

CABI,TRIM -AC17

HLDR,HALF-C

6 8A-KCF-021-010

7 8A-KCH-001-010

8 8A-KC7-011-010

9 8A-KCF-208-010

10 8A-KC7-013-010

WINDOW,SIDE L -AC15

CABI,FRONT -AC17

BTN,CLEAR L -AC

HLDR,BTN R1 -AC15

BTN,CLEAR ML -AC

31 8Z-KC1-213-010

32 8A-KC7-230-010

33 8Z-KC1-211-010

34 8Z-KC7-201-010

35 8Z-KC3-201-010

CHAS,SIDE L -C

HLDR,TR2-AC

COVER, TOP -C

COVER, ISO BLIND -C

COVER, CD BLIND -C

11 8A-KCF-012-010

12 8A-KCF-209-010

13 8A-KCF-008-010

14 8A-KCF-010-010

15 8A-KC7-006-010

BTN,CLEAR EJ -AC15

HLDR,BTN R2 -AC15

BTN,MONO -AC15

BTN,CLEAR S2 -AC15

BTN,PRE.-AC

36 8A-KC7-224-010

37 8Z-KC1-214-010

38 8Z-KC1-212-010

A 87-251-075-410

B 87-B10-216-010

HLDR,P-IC -AC

CHAS,SIDE R -C

COVER, BOTTOM -C

U+2.6-10

U+2.6-4.0ZWC BLK

16 8A-KC7-007-010

17 8A-KCF-007-010

18 8A-KC7-014-010

19 8A-KC7-208-010

20 8A-KCF-211-010

BTN,SEESAW R -AC

BTN,SEESAW L -AC15

BTN,CLEAR S -AC

HLDR,BTN L-AC

C 87-251-073-410

D 87-251-100-410

E 87-B10-259-010

F 87-432-903-010

G 8Z-KC1-251-010

SCREW,U+2.6-6

U+3-16

UT2+3.0-10.0 W/O SLOT (BH TAP)

WASHER,WTE 2.6

LENS,ENCO -AC15

S-SCREW,TH2.6-4.0-0.8

21 8A-KCF-212-010

22 8A-KCF-215-010

23 8A-KCG-610-010

24 8A-KCF-213-010

25 8A-KCF-214-010

LENS,R -AC15

HLDR,LCD -AC15

LCD,AKC-16-17

LENS,LCD -AC15

CASE,LCD LENS -AC15

COLOR NAME TABLE

Basic color symbol

Color

Black

Green

Basic color symbol

Color

Basic color symbol

Color

Orange

Blue

Pink

Titan Silver

White

Cream

Gray

Transparent Blue

Red

Gold

Silver

Brown

Violet

Transparent White

Metallic Blue

Dark Blue

Yellow

Transparent Yellow

Transparent Green

Light Blue

Transparent Orange

- 33 -

CD MECHANISM EXPLODED VIEW 1 / 1

20 19

P.C.B

- 34 -

CD MECHANISM PARTS LIST 1 / 1

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

1 S3-031-010-010

2 S3-031-050-240

3 S3-031-010-260

4 S3-031-010-270

5 S3-031-010-290

FRAME

DAMPER(J)

REAR OAMPER BKT(J)

FPC GUIDE

41 S3-031-050-220

42 S3-031-050-080

43 S6-901-160-110

44 S3-031-050-110

45 S3-031-050-120

LOCK PIN BL

PU SHAFT

PICK-UP OPTIMA-720AIE

PU M NUT

NUT PUSH SPR PL

HUNG UP SP(R)

6 S3-031-010-140

7 S3-031-010-160

8 S3-031-010-120

9 S3-031-010-150

10 S3-031-113-020

TRIG PL

TRIG ARM

TRIG LVR

TRIG PL SPRING

LDG RLR SFT ASSY

46 S3-031-053-030

47 S3-031-050-040

48 S3-030-050-100

49 S6-418-040-040

50 S3-031-053-010

FEED SCREW ASSY

FD GR BLK

PU GEAR(B)

DET SW ESE11HS2

FEED MOTOR ASSY

11 S3-031-010-200

12 S3-031-010-180

13 S3-031-010-210

14 S3-031-010-220

15 S3-031-010-170

FIX PL(R)

FIX ARM(R)

LDG GR(6)

LDG GR(6)SPRING

FIX ARM(L)

51 S3-031-110-300

52 S3-031-110-180

53 S3-031-110-080

54 S3-031-110-310

55 S3-031-110-100

FRONT BRKT(J)

L.P SPRING(L)

GR MT BLK

LDG ROLLER(S)

LDG GR(3)

16 S3-031-010-190

17 S3-031-010-030

18 S3-031-010-070

19 S3-031-010-080

20 S3-031-010-330

FIX PL(L)

DAMPER PIN

UPPER PL

SEL STOP PL

S ARM SPRING(B)

56 S3-031-110-090

57 S3-031-110-290

58 S3-031-110-050

59 S3-031-113-010

60 S3-031-110-190

LDG GR(2)

LDG BELT

SUPPORT PL

LDG MOTOR ASSY

L.P SPRING(R)

21 S3-031-010-100

22 S3-031-010-250

23 S3-031-010-240

24 S3-031-110-240

25 S3-031-110-230

SEL ARM (R)

S.L ARM SPRING

S.L ARM

SW ACTR

SW PCB

61 S3-031-010-300

62 S9-W07-350-800

63 S3-031-110-120

64 S6-815-020-350

65 S6-817-020-240

LEVER SP

LUMILAR W 2.3-9.8-0.35

LDG GR(5)

CONNECTOR TKC-F14P-J3

CONNECTOR 6208010115

26 S6-418-040-020

27 S6-418-040-030

28 S3-031-010-090

29 S3-031-050-010

30 S3-031-050-130

DET SW ESE22MH1

DET SW ESE22MH3

SEL ARM (L)

TTB

66 S6-815-020-370

67 S9-W03-302-760

68 S9-W06-400-300

A 87-841-034-410

B 87-741-033-410

CONNECTOR TKC-F12P-J3

NW BLUE 2.9-5-0.3

HLW CUT 1.4-3.2-0.4

CAMERA B TAOPPING SCREW M2-5

CAMERA SCREW TS.G M2-4

CLP ARM

31 S3-031-050-360

32 S3-031-050-230

33 S3-031-050-150

34 S3-031-050-140

35 S3-031-050-250

STOPPER SPR

CLAMPER PLATE

CLAMPER

CLP ARM SPRING

CLP ARM SPR(L)

C 87-351-549-310

D 87-267-525-310

E 87-B10-026-010

F 87-078-159-110

G 87-067-643-010

CAMERA B TAPPING SCREW M2-4

CAMERA SCREW M1.7-2.2

CAMERA TAPPING SCREW S M1.7-8

CAMERA TAPPING SCREW S 3 M2-2

CAMERA TAPPING SCREW B 3 M2-10

36 S3-031-053-020

37 S3-031-050-030

38 S3-031-050-210

39 S3-031-050-100

40 S3-031-010-280

SPINDLE MOTOR ASSY

FMB

LOCK PIN

THRUST SPR

HUNG UP SP(F)

H 87-841-034-410

I 87-261-032-410

CAMERA TAPPING SCREW B 3 M2-5

TAMS SCREW M2-3

- 35 -

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111

9820572 0251431

Printed in Singapore

Black Box Cable Box QuietCab Elite User Manual
Canon VIXIA HR10 User Manual
Casio Camcorder EX Z30 User Manual
EverFocus DVR EDR410H User Manual
Extron electronic Extron Electronics Cable Box 200 User Manual
HP (Hewlett Packard) Hewlett Packard Car Video System 2310 User Manual
iSimple DUALINK PGHNI2 User Manual
JBL GTO426 User Manual
JBL Professional JBL Control 300 User Manual
JVC Everio Digital Camcorder GZE100RUS User Manual