Portable Projector
M361X/M311X/M271X/
M311W/M271W
User’s Manual
The M361X and M271X are not distributed in North America.
Model No.
NP-M361X, NP-M311X, NP-M271X, NP-M311W, NP-M271W
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC projector and keep the manual handy for future reference.
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS
CAN BE FULLY INSERTED.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula-
tions.
Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in accordance with EN ISO 7779.
CAUTION
Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The static background from previous images will
disappear.
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and electronic prod-
ucts carrying the mark (left) must be disposed of separately from normal household waste. This includes
projectors and their electrical accessories or lamps. When you dispose of such products, please follow the
guidance of your local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort will help us
reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human health
and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European Union Member
States.
i
Important Information
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regu-
lation could void your right to operate this equipment. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cord with moulded plug has a Black (five Amps) fuse installed for use with
this equipment. If a power cord is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
• Do not place the projector in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths, or damp rooms.
- in direct sunlight, near heaters, or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• If you wish to have the projector installed on the ceiling:
- Do not attempt to install the projector yourself.
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk
of bodily injury.
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance
with any local building codes.
- Please consult your dealer for more information.
ii
Important Information
WARNING
•
Do not use any other object than the projector’s sliding lens cover to cover the lens while the projector is on.
Doing so can cause the object to get extremely hot, and possibly resulting in a fire or damage due to the heat
emitted from the light output.
•
Do not place any objects, which are easily affected by heat, in front of the projector lens. Doing so could lead
to the object melting from the heat that is emitted from the light output.
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other
than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
10°
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your
projector. Allow at least 4 inches (10cm) of space between your projector and a wall.
• Do not try to touch the exhaust vent on the left front (when seen from the front) as it can become heated while the
projector is turned on and immediately after the projector is turned off. Parts of the projector may become temporarily
heated if the projector is turned off with the POWER button or if the AC power supply is disconnected during normal
projector operation.
Use caution when picking up the projector.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve
any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your
projector. If something should fall into your projector, disconnect it immediately and have the object removed by a
qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply
fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
• Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause
unpredictable outcome such as fire or injury to the eyes.
• Do not place any objects, which are easily affected by heat, in front of a projector exhaust vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the ex-
haust.
• Do not splash water over the projector. Doing so can cause electrical shock or fire. If the projector gets wet, turn off
the projector, unplug the power cord and have the projector serviced by a qualified service personnel.
iii
Important Information
• Handle the power cord carefully. A damaged or frayed power cord can cause electric shock or fire.
- Do not use any power cord other than the one supplied with the projector.
- Do not bend or tug the power cord excessively.
- Do not place the power cord under the projector, or any heavy object.
- Do not cover the power cord with other soft materials such as rugs.
- Do not heat the power cord.
- Do not handle the power plug with wet hands.
• Turn off the projector, unplug the power cord and have the projector serviced by a qualified service personnel under
the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.
- If the projector does not operate normally when you follow the instructions described in this user’s manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
• Disconnect the power cord and any other cables before carrying the projector.
• Turn off the projector and unplug the power cord before cleaning the cabinet or replacing the lamp.
• Turn off the projector and unplug the power cord if the projector is not to be used for an extended period of time.
• When using a LAN cable (only models with the RJ-45 LAN port):
For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.
CAUTION
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hang-
ing on the wall can cause damage to the projector.
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the
soft case could be damaged.
• Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[SETUP] → [OPTIONS(1)] → [FAN MODE] → [HIGH].)
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is blink-
ing blue. Doing so could cause premature lamp failure.
Remote Control Precautions
•
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not short, heat, or take apart batteries.
Do not throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/−) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
iv
Important Information
Note for US Residents
The lamp in this product contains mercury. Please dispose according to Local, State or Federal Laws.
Lamp Replacement
• Use the specified lamp for safety and performance.
• Be sure to replace the lamp and filter when the message [THE LAMP HAS REACHEDTHE END OF ITS USABLE
LIFE. PLEASE REPLACE THE LAMP AND FILTER.] appears. If you continue to use the lamp after the lamp has
reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case.
Do not touch them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on
and off will increase the possibility of its lower brightness.
The actual lamp life may vary depending upon the individual lamp, the environmental conditions and usage.
CAUTION:
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off
and then disconnect the power cord. Allow at least one hour for the lamp to cool before handling.
• When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass
fragments could fall if the lamp has been burned out.
About High Altitude mode
•
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters
or higher.
Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE]
can cause the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and
turn on the projector.
•
•
Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE]
can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical com-
ponents such as the lamp.
About Copyright of original projected pictures:
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue
such as a coffee shop or hotel and employing compression or expansion of the screen image with the following func-
tions may raise concern about the infringement of copyrights which are protected by copyright law.
[ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features.
Turkish RoHS information relevant for Turkish market
EEE Yonetmeliğine Uygundur.
This device is not intended for use in the direct field of view at visual display workplaces.To avoid incommoding reflec-
tions at visual display workplaces this device must not be placed in the direct field of view.
v
Table of Contents
Important Information............................................................................................i
1. Introduction.......................................................................................................... 1
1 What’s in the Box?......................................................................................................... 1
Introduction to the Projector .......................................................................................... 2
Congratulations on Your Purchase of the Projector ................................................. 2
Features you’ll enjoy: ............................................................................................... 2
About this user’s manual.......................................................................................... 3
Part Names of the Projector .......................................................................................... 4
Front/Top.................................................................................................................. 4
Rear ......................................................................................................................... 5
Top Features............................................................................................................ 6
Terminal Panel Features .......................................................................................... 7
Part Names of the Remote Control ............................................................................... 8
Battery Installation ................................................................................................... 9
Remote Control Precautions.................................................................................... 9
Operating Range for Wireless Remote Control........................................................ 9
Operating Environment.......................................................................................... 11
1 Flow of Projecting an Image........................................................................................ 13
Connecting Your Computer/Connecting the Power Cord............................................. 14
Turning on the Projector .............................................................................................. 15
Selecting a Source ...................................................................................................... 17
Selecting the computer or video source................................................................. 17
Adjusting the Picture Size and Position....................................................................... 18
Adjust the Tilt Foot ................................................................................................. 19
Focus ..................................................................................................................... 20
Correcting Keystone Distortion Manually .................................................................... 21
Adjusting with buttons on the cabinet .................................................................... 21
Adjusting with the remote control........................................................................... 22
Optimizing Computer Signal Automatically ................................................................. 23
Adjusting the Image Using Auto Adjust.................................................................. 23
Turning Up or Down Volume ........................................................................................ 23
Turning off the Projector .............................................................................................. 24
After Use...................................................................................................................... 25
3. Convenient Features..................................................................................... 26
1 Turning off the Image and Sound ................................................................................ 26
Freezing a Picture ....................................................................................................... 26
Enlarging a Picture ...................................................................................................... 26
Changing Eco Mode/Checking Energy-Saving Effect ................................................ 27
Using Eco Mode [ECO MODE].............................................................................. 27
vi
Table of Contents
(USB Display) ........................................................................................................ 39
Controlling the Projector by Using an HTTP Browser ................................................. 41
Controlling the Projector over a LAN (PC Control Utility Pro 4/Pro 5) ......................... 48
Express Utility Lite) ................................................................................................ 52
Utility Lite) .............................................................................................................. 57
What you can do with GCT.................................................................................... 57
Projecting an Image from an Angle (GCT)............................................................. 57
4. Using the Viewer............................................................................................. 59
❶ What you can do with the Viewer................................................................................. 59
❷ Projecting images stored in a USB memory device .................................................... 61
5. Using On-Screen Menu................................................................................ 70
1 Using the Menus.......................................................................................................... 70
Menu Elements............................................................................................................ 71
List of Menu Items ....................................................................................................... 72
Menu Descriptions & Functions [SOURCE] ................................................................ 75
COMPUTER 1 and 2 ............................................................................................. 75
HDMI...................................................................................................................... 75
VIDEO.................................................................................................................... 75
S-VIDEO ................................................................................................................ 75
VIEWER................................................................................................................. 75
NETWORK............................................................................................................. 75
USB DISPLAY........................................................................................................ 75
Menu Descriptions & Functions [ADJUST].................................................................. 76
[PICTURE] ............................................................................................................. 76
[IMAGE OPTIONS] ................................................................................................ 79
Menu Descriptions & Functions [SETUP].................................................................... 83
[GENERAL]............................................................................................................ 83
[MENU] .................................................................................................................. 85
[INSTALLATION] .................................................................................................... 87
[OPTIONS(1)] ........................................................................................................ 89
[OPTIONS(2)] ........................................................................................................ 91
Menu Descriptions & Functions [INFO.] ...................................................................... 96
[USAGE TIME]....................................................................................................... 96
[SOURCE].............................................................................................................. 97
vii
Table of Contents
[WIRED LAN]......................................................................................................... 97
[WIRELESS LAN] .................................................................................................. 97
[VERSION]............................................................................................................. 98
[OTHERS].............................................................................................................. 98
Menu Descriptions & Functions [RESET].................................................................... 99
Returning to Factory Default [RESET]................................................................... 99
6. Installation and Connections................................................................. 100
1 Setting Up the Screen and the Projector................................................................... 100
Selecting a Location............................................................................................. 100
Throw Distance and Screen Size......................................................................... 102
Making Connections.................................................................................................. 104
Connecting Your Computer .................................................................................. 104
Connecting an External Monitor .......................................................................... 106
Connecting Component Input .............................................................................. 108
Connecting HDMI Input........................................................................................ 109
Connecting to a Wired LAN ................................................................................. 110
7. Maintenance .................................................................................................... 114
1 Cleaning the Filters.................................................................................................... 114
Cleaning the Lens...................................................................................................... 116
Cleaning the Cabinet................................................................................................. 116
Replacing the Lamp and the Filters........................................................................... 117
8. Appendix............................................................................................................. 122
1 Troubleshooting ......................................................................................................... 122
Indicator Messages.............................................................................................. 122
Common Problems & Solutions........................................................................... 123
If there is no picture, or the picture is not displayed correctly............................... 124
Specifications ............................................................................................................ 125
Cabinet Dimensions .................................................................................................. 127
Compatible Input Signal List...................................................................................... 129
PC Control Codes and Cable Connection................................................................. 130
Troubleshooting Check List........................................................................................ 131
TCO Certification....................................................................................................... 133
Mexico) ................................................................................................................ 134
viii
1. Introduction
1 What’s in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.
Projector
Soft case
(24BS8121)
Power cord
(US: 7N080236)
(EU: 7N080022)
Computer cable (VGA)
(7N520073/7N520052)
Remote control
(7N900924)
Batteries (AAA × 2)
For North America only
Limited warranty
For customers in Europe:
You will find our current valid
Guarantee Policy on our Web
Site:
NEC Projector CD-ROM
User’s manual (PDF) and the utility
software
www.nec-display-solutions.com
(7N951851)
•
•
Important Infomation (For North
America: 7N8N3151) (For Other
countries than North America:
7N8N3151 and 7N8N3161)
Quick Setup Guide (7N8N3171)/
(7N8N3181)
Unless otherwise described in the user’s manual, the drawings for the projector cabinet show examples of the M361X.
1
1. Introduction
Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of the Projector
This projector is one of the very best projectors available today. The projector enables you to project precise images
up to 300 inches across (measured diagonally) from your PC or Mac computer (desktop or notebook), VCR, DVD
player, or document camera.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
1
*
Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk
of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance
with any local building codes. Please consult your dealer for more information.
Features you’ll enjoy:
•
Quick start (3 seconds*2), Quick Power Off, Direct Power Off
3 seconds*2 after turning on the power, the projector is ready to display PC or video images.
The projector can be put away immediately after the projector is powered down. No cool down period is required
after the projector is turned off from the remote control or cabinet control panel.
The projector has a feature called “Direct Power Off”.This feature allows the projector to be turned off (even when
projecting an image) by using the Main Power Switch or disconnecting the AC power supply.
To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and
a breaker.
*2 The quick start time is only when [STANDBY MODE] is set to [NORMAL] in the on-screen message.
•
•
0.2 W (100-130 V AC)/0.4 W (200-240 V AC) in standby condition with energy saving technology
Selecting [POWER-SAVING] for [STANDBY MODE] from the menu can put the projector in power-saving mode
that consumes only 0.2 W (100-130 V AC)/0.4 W (200-240 V AC).
Carbon Meter
This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector’s [ECO
MODE] is set to [AUTO ECO], [NORMAL], or [ECO].
The amount of CO2 emission reduction will be displayed in the confirmation message at the time of power-off and
in the INFO of the on-screen menu.
•
Lamp life up to 10000 hours*3
Using in Eco Mode (ECO) allows you to prolong the projector’s lamp life up to 10000 hours (up to 5000 hours in
ECO MODE OFF).
*3 M361X/M311W: 8000 hours (up to 4000 hours in ECO MODE OFF).
HDMI input port provides digital signal
•
•
The HDMI input provides HDCP compatible digital signals. The HDMI input also supports audio signal.
10 W built-in speaker for an integrated audio solution
Powerful 10 watt monaural speaker provides volume need for large rooms.
2
1. Introduction
•
The supplied remote control allows you to assign a CONTROL ID to the projector
Multiple projectors can be operated separately and independently with the same single remote control by assigning
an ID number to each projector.
•
•
Auto vertical keystone correction
Auto Keystone feature allows the projector to detect its tilt and correct vertical distortion automatically.
USB Display
Using a commercially available USB cable (compatible with USB 2.0 specifications) to connect the computer with
the projector allows you to send your computer screen image to the projector without the need of a traditional
computer cable (VGA).
•
•
Integrated RJ-45 connector for wired networking capability along with wireless networking capabilities
An RJ-45 connector is standard. An optional USB Wireless LAN Unit is required for wireless LAN connection.
Software programs (User Supportware) contained in the supplied CD-ROM
The supplied NEC Projector includes four programs:Virtual Remote Tool, Image Express Utility Lite (for Windows/
Mac OS), PC Control Utility Pro 4 (for Windows)/5 (for Mac OS), and Viewer PPT Converter 3.0.
Image Express Utility Lite (for Windows) can be started from a commercially available USB memory or SD card
without the need of installing on your computer.
•
•
•
•
AUTO POWER ON and AUTO POWER OFF features
The DIRECT POWER ON, AUTO POWER ON(COMP1), AUTO POWER OFF, and OFF TIMER features eliminate
the need to always use the POWER button on the remote control or projector cabinet.
Preventing unauthorized use of the projector
Enhanced smart security settings for keyword protection, cabinet control panel lock, security slot, and security
chain opening to help prevent unauthorized access, adjustments and theft deterrence.
High resolution up to WUXGA
High resolution display - up to WUXGA compatible, XGA (M361X/M311X/M271X)/WXGA (M311W/M271W) native
resolution.
CRESTRON ROOMVIEW compatibility
The projector supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be man-
aged and controlled from a computer or controller.
About this user’s manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find
an overview. If the section doesn’t apply, you can skip it.
3
1. Introduction
Rear
Port Cover for Optional USB
Wireless LAN Unit
When using the optional USB
Wireless LAN Unit, first remove
Monaural Speaker (10 W)
Built-in Security Slot ( )*
AC Input
Connect the supplied power cord’s
three-pin plug here, and plug the
other end into an active wall outlet.
Security chain opening
Attach an anti-theft device.
The security chain opening accepts
security wires or chains up to 0.18
inch/4.6 mm in diameter.
* This security slot supports the MicroSaver ® Security System.
Opening and closing the lens cover
Slide the lens cover to the left to uncover the lens.
To cover the lens, slide the lens cover to the right.
NOTE:
• The lens cover works in conjunction with the AV-MUTE function. Closing the lens cover will turn off the image and sound during
normal projector operation; opening it will restore the image and sound.
With the lens cover closed the image and sound is turned off, however the lamp is still lit. If the projector stays this way for about
2 hours, it will turn off automatically.
• Do not pull the lens cover with excessive force or apply strong pressure in either the up or down direction. Doing so can cause
damage to the lens cover sliding mechanism!
5
1. Introduction
Terminal Panel Features
13 12
6
5
4
3
2
9
1
7
10
11
8
14
1. COMPUTER 1 IN/ Component Input Connector
2. COMPUTER 1 AUDIO IN Mini Jack (Stereo Mini)
3. COMPUTER 2 IN / Component Input Connector
4. COMPUTER 2 AUDIO IN Mini Jack (Stereo Mini)
5. HDMI IN Connector (Type A)
6. USB (PC) Port (Type B)
7. MONITOR OUT (COMP. 1) Connector (Mini D-Sub
9. S-VIDEO IN Connector (Mini DIN 4 Pin)
11. VIDEO/S-VIDEO AUDIO IN L/MONO, R (RCA)
14. PC CONTROL [PC CONTROL] Port (D-Sub 9 Pin)
Use this port to connect a PC or control system. This
enables you to control the projector using serial commu-
nication protocol. If you are writing your own program,
7
1. Introduction
Part Names of the Remote Control
1
3
7
2
5
6
10
4
8
9
11
14
17
15
13
12
14. ID SET Button
16
19
18
15. Numeric Keypad Button/CLEAR Button
20
25
21
22
16. FREEZE Button
27
24
28
17. AV-MUTE Button
23
26
18. MENU Button
29
32
30
31
22. D-ZOOM (+)(–) Button
23. MOUSE L-CLICK Button*
24. MOUSE R-CLICK Button*
1. Infrared Transmitter
25. PAGE / Button
2. POWER ON Button
3. POWER OFF Button
27. KEYSTONE Button
4, 5, 6. COMPUTER 1/2/3 Button
28. PICTURE Button
(COMPUTER 3 button is not available.)
29. VOL. (+)(–) Button
7. AUTO ADJ. Button
30. ASPECT Button
8. VIDEO Button
31. FOCUS/ZOOM Button
9. S-VIDEO Button
(not available on this series of projectors)
32. HELP Button
* The MOUSE L-CLICK and MOUSE R-CLICK buttons work only when a USB cable is connected with your com-
puter.
8
1. Introduction
Battery Installation
Press firmly and slide the battery
cover off.
Install new batteries (AAA).Ensure
that you have the batteries’polarity
(+/−) aligned correctly.
Slip the cover back over the bat-
teries until it snaps into place. Do
not mix different types of batteries
or new and old batteries.
1
2
3
OPEN
OPEN
Remote Control Precautions
•
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not short, heat, or take apart batteries.
Do not throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/−) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
22 feet/7 m
30°
Remote control
30°
Remote sensor on projector cabinet
Remote control
30°
30°
22 feet/7 m
•
•
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
9
1. Introduction
Operating Environment for Software Included on CD-ROM
Names and Features of Bundled Software Programs
Name of software program
Features
Virtual Remote Tool
(Windows only)
This is a software program used to control the power ON/OFF and source selec-
tion of the projector from your computer by using the supplied computer cable
Name of software program
Features
Image Express Utility Lite
Image Express Utility Lite for
Mac OS
• This is a software program used to project your computer’s screen over the
USB cable or the wired/wireless network. The computer cable (VGA) is not
• This software program can be used to control the power ON/OFF and source
selection of the projector from your computer.
• The Geometric Correction Tool (GCT) function allows you to correct distortion
* “USB Display” and “GCT” functions are not supported by Mac.
Name of software program
Features
PC Control Utility Pro 4
PC Control Utility Pro 5 (for Mac
OS)
This is a software program used to operate the projector from the computer when
the computer and the projector are connected with LAN (wired or wireless) or
Name of software program
Features
Viewer PPT Converter 3.0
(Windows only)
This is a software program used to convert files created with PowerPoint into
JPEG files that can be displayed with the viewer function of the projector when
NOTE:
• Image Express Utility Lite does not support "Meeting Mode" in Image Express Utility 2.0 included with our other models.
Download service
For the update information about these software programs, visit our website:
10
1. Introduction
Operating Environment
The following is the operating environment for Image Express Utility Lite. For the operating environment of other soft-
ware program, refer to the help function of each software program.
[Windows]
Supported OS
Windows 7 Home Basic
Windows 7 Home Premium
Windows 7 Professional
Windows 7 Ultimate
Windows 7 Enterprise
Windows Vista Home Basic
Windows Vista Home Premium
Windows Vista Business
Windows Vista Ultimate
Windows Vista Enterprise
Windows XP Home Edition (32-bit version) Service Pack 3 or later
Windows XP Professional (32-bit version) Service Pack 3 or later
• Windows power-saving function is not supported.
Processor
• Windows 7/Windows Vista
Pentium M 1.2 GHz equivalent or higher required
Dual core 1.5 GHz or higher recommended
• Windows XP
Pentium M 1.0 GHz equivalent or higher required
Dual core 1.0 GHz or higher recommended
Memory
• Windows 7/Windows Vista
512 MB or more required
1 GB or more recommended
• Windows XP
256 MB or more required
512 MB or more recommended
* More memory may be required to run additional applications simultane-
ously.
Graphic processor
• Windows 7/Windows Vista
The “Graphics” score 3.0 or more of “Windows Experience Index” recom-
mended.
Network environment
Resolution
TCP/IP-compatible wired LAN or wireless LAN
(* Use a wireless LAN unit complying with the Wi-Fi standard.)
• Windows 7/Windows Vista
SVGA (800 × 600) or higher required
XGA (1024 × 768) recommended
• Windows XP
VGA (640 × 480) or higher required
XGA (1024 × 768) recommended
1024 dots × 768 lines - 1280 dots × 800 lines recommended (M311W/
M271W)
Screen Colors
High Color (15 bits, 16 bits)
True Color (24 bits, 32 bits) (recommended)
• 256 or fewer colors are not supported.
11
1. Introduction
[Mac]
Supported OS
Mac OS X v10.6, v10.7
Processor (CPU)
Intel® Core™ Duo processor 1.5 GHz or higher required
Intel® Core™ 2 Duo processor 1.6 GHz or higher recommended
* PowerPC® is not supported
Memory
512 MB or higher required
Network environment
Wired or wireless LAN required that supports TCP/IP
Only wireless LAN units built into Mac are guaranteed to work with Image
Express Utility Lite.
“Easy Connection” supports only wireless LAN.
Supported Resolution
VGA (640 × 480) or higher required
XGA (1024 × 768) recommended
(1024 × 768 – 1280 × 800 recommended for M311W/M271W)
Supported Screen Colors
16.70 million colors required
12
2. Projecting an Image (Basic Operation)
Connecting Your Computer/Connecting the Power Cord
1. Connect your computer to the projector.
This section will show you a basic connection to a computer. For information about other connections, see “6.
Connect the computer cable (VGA) between the projector’s COMPUTER 1 IN connector and the computer’s port
(mini D-Sub 15 Pin). Turn two thumb screws of both connectors to fix the computer cable (VGA).
2. Connect the supplied power cord to the projector.
First connect the supplied power cord’s three-pin plug to the AC IN of the projector, and then connect the other
plug of the supplied power cord in the wall outlet.
The projector’s power indicator will flash for a few seconds and then will light orange* (standby mode).
The STATUS indicator will also light green*.
* This will apply for both indicators when [NORMAL] is selected for [STANDBY MODE]. See the Power Indicator
COMPUTER 1 IN
Make sure that the prongs are fully inserted into
both the AC IN and the wall outlet.
To wall outlet ←
CAUTION:
Parts of the projector may become temporarily heated if the projector is turned off with the POWER button or if the
AC power supply is disconnected during normal projector operation.
Use caution when picking up the projector.
14
2. Projecting an Image (Basic Operation)
Turning on the Projector
1. Slide the lens cover to the left to uncover the lens.
2. Press the
(POWER) button on the projector cabinet
or the POWER ON button on the remote control.
The POWER indicator will turn to blue and the projector
will become ready to use.
TIP:
• When the message “Projector is locked! Enter your password.”
is displayed, it means that the [SECURITY] feature is turned on.
Standby
Blinking
Power On
After you turn on your projector, ensure that the computer
or video source is turned on and that the lens cover is
open.
NOTE: When no input signal is present, the no-signal guidance is
displayed (factory menu setting).
Steady orange light
Blinking blue light Steady blue light
15
2. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 29 menu languages.
To select a menu language, follow these steps:
1. Use the , , or button to select one of the 29
languages from the menu.
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu
operation.
If you want, you can select the menu language later.
NOTE:
• When turning off the power supply and then back on by using a power strip or breaker.
Allow a minimum of 1 second between turning off the main power supply and turning it back on again.
Failing to do so could result in no power to the projector. (There will be no stand-by LED)
Should this happen, unplug the power cord and plug it in again. Turn on the main power.
• If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the
projector will not turn on to protect the internal system. If this happens, wait for the projector’s internal components to cool
down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
• If the STATUS indicator lights orange with the power button pressed, it means that the [CONTROL PANEL LOCK] is turned on.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on
the power.
• While the POWER indicator is blinking blue in short cycles, the power cannot be turned off by using the power button.
• Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp lighting is
stabilized.
• When the projector is turned on, it may take some time before the lamp light becomes bright.
• If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans run without display-
ing an image for some time and then the projector will display the image.
16
2. Projecting an Image (Basic Operation)
Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.
Detecting the Signal Automatically
Press the SOURCE button once.The projector will search for the available
input source and display it. The input source will change as follows:
COMPUTER1 → COMPUTER2 → HDMI → VIDEO → S-VIDEO →
VIEWER → USB DISPLAY → COMPUTER1 → ...
•
With the SOURCE screen displayed, you can press the SOURCE
button a few times to select the input source.
TIP: If no input signal is present, the input will be skipped.
Using the Remote Control
Press any one of the COMPUTER1, COMPUTER2, HDMI, VIDEO, S-
VIDEO, VIEWER, NETWORK, or USB DISPLAY buttons.
Selecting Default Source
You can set a source as the default source so that it will be displayed
each time the projector is turned on.
1. Press the MENU button.
The menu will be displayed.
2. Press the button twice to select [SETUP] and press the but-
ton or the ENTER button to select [GENERAL].
3. Press the
button four times to select [OPTIONS(2)].
4. Press the button five times to select [DEFAULT SOURCE SE-
LECT] and press the ENTER button.
The [DEFAULT SOURCE SELECT] screen will be displayed.
5. Select a source as the default source, and press the ENTER but-
ton.
6. Press the EXIT button a few times to close the menu.
7. Restart the projector.
The source you selected in step 5 will be projected.
NOTE: Even when [AUTO] is turned on, the [NETWORK] will not be automatically
selected. To set your network as the default source, select [NETWORK].
TIP:
• When the projector is in Standby mode, applying a computer signal from a
computer connected to the COMPUTER 1 IN input will power on the projector
and simultaneously project the computer’s image.
• On Windows 7, a combination of the Windows and P keys allows you to set up
external display easily and quickly.
17
2. Projecting an Image (Basic Operation)
Adjusting the Picture Size and Position
Use the adjustable tilt foot, the zoom function or the focus ring to adjust the picture size and position.
In this chapter drawings and cables are omitted for clarity.
Adjusting the throw angle (the height of an image)
Adjusting the left and right tilt of an image
Finely adjusting the size of an image
Adjusting the focus
Automatic Keystone Correction function is turned on at the time of shipment.
To perform keystone correction manually, see “6. Correcting Keystone Distortion Manually” on page 21.
18
2. Projecting an Image (Basic Operation)
Adjust the Tilt Foot
1. Lift the front edge of the projector.
CAUTION:
1
Do not try to touch the exhaust vent during Tilt Foot adjustment as
it can become heated while the projector is turned on and after it is
turned off.
2. Push up and hold the Adjustable Tilt Foot Lever on the front of
the projector to extend the adjustable tilt foot.
2
3. Lower the front of the projector to the desired height.
Adjustable Tilt
Foot Lever
Adjustable Tilt Foot
4. Release the Adjustable Tilt Foot Lever to lock the Adjustable tilt
foot.
The tilt foot can be extended up to 1.6 inch/40 mm.
There is approximately 10 degrees (up) of adjustment for the front of
the projector.
Rotate the rear foot to the desired height in order to square the image
on the projection surface.
CAUTION:
• Do not use the tilt-foot for purposes other than originally intended.
Misuses such as using the tilt foot to carry or hang (from the wall or
ceiling) the projector can cause damage to the projector.
3
Adjusting the left and right tilt of an image [Rear foot]
•
Rotate the rear foot.
The rear foot can be extended up to 0.5 inch/12 mm. Rotating the rear
foot allows the projector to be placed horizontally.
NOTE:
• Do not extend the rear foot beyond its height limit (0.5 inch/12 mm). Doing so
may cause the rear foot to come out of the projector.
Rear foot
Up
Down
19
2. Projecting an Image (Basic Operation)
Correcting Keystone Distortion Manually
If the screen is tilted vertically, keystone distortion becomes large. Automatic Keystone Correction function is turned on
at the time of shipment. To correct keystone distortion manually, proceed with the following steps to correct keystone
distortion.
NOTE:
• The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
• The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.
Adjusting with buttons on the cabinet
1. Press the or button with no menus displayed.
The keystone bar will be displayed.
2. Use the or to correct the keystone distortion.
The keystone bar will be closed after a period of time.
3. Press the ENTER button.
The keystone bar will be closed.
NOTE:
• When the menu is displayed, the above operation is not available. When the menu is displayed, press the MENU button to close
the menu and start the Keystone correction.
From the menu, select [SETUP] → [GENERAL] → [KEYSTONE]. The changes can be saved with [KEYSTONE SAVE]. (→ page
• Keystone control is not available with the or button when VIEWER is used.
21
2. Projecting an Image (Basic Operation)
Adjusting with the remote control
1. Press the KEYSTONE button.
The Keystone bar will be displayed.
2. Use the or button to correct the keystone distortion.
Adjust so that the right and left sides are parallel.
3. Press the EXIT button.
The Keystone bar will be closed.
22
2. Projecting an Image (Basic Operation)
Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
Optimizing a computer image automatically. (COMPUTER1/COMPUTER2)
Press the AUTO ADJ. button to optimize a computer image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
[Normal picture]
NOTE:
Some signals may take time to display or may not be displayed correctly.
• If the Auto Adjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE]
Turning Up or Down Volume
Sound level from the speaker can be adjusted.
Increase volume
Decrease volume
TIP: When no menus appear, the and buttons on the projector cabinet work
as a volume control.
NOTE:
• Volume control is not available with the or button when an image is enlarged
by using the D-ZOOM (+) button or when the menu is displayed.
• Volume control is not available with the or button when VIEWER is
used.
TIP: The [BEEP] sound volume cannot be adjusted. To turn off the [BEEP] sound,
from the menu, select [SETUP] → [OPTIONS (1)] → [BEEP] → [OFF].
23
2. Projecting an Image (Basic Operation)
Turning off the Projector
To turn off the projector:
1. First, press the
(POWER) button on the projector
cabinet or the POWER OFF button on the remote con-
trol.
The confirmation message will be displayed.
Power On
Standby
2. Secondly, press the ENTER button or press the
(POWER) or the POWER OFF button again.
The lamp will turn off and the projector will go into standby
mode. When in standby mode, the POWER indicator will
light orange and the STATUS indicator will light green when
[NORMAL] is selected for [STANDBY MODE].
Steady blue light
Steady
orange light
CAUTION:
Parts of the projector may become temporarily heated if the projector is turned off with the POWER button or if the
AC power supply is disconnected during normal projector operation.
Use caution when picking up the projector.
NOTE:
• While the power indicator is blinking blue in short cycles, the power cannot be turned off.
• You cannot turn off the power for 60 seconds immediately after turning it on and displaying an image.
• Do not disconnect the AC power supply to the projector within 10 seconds of making adjustment or setting changes and closing
the menu. Doing so can cause loss of adjustments and settings.
24
2. Projecting an Image (Basic Operation)
After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cord.
2. Disconnect any other cables.
•
Remove the USB memory if it is inserted into the projector.
3. Retract adjustable tilt foot if extended.
4. Slide the lens cover to the right to cover the lens.
5. Put the projector and accessories in the supplied soft case.
Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from
damage.
Insert the projector with the lens
facing upward
NOTE: When placing the projector in the soft case, retract the tilt foot and the rear feet. Failure to do so may case damage to the
projector.
CAUTION:
Use caution when putting the projector in the soft case immediately after the projector has been operating. The
projector cabinet is hot.
25
3. Convenient Features
1 Turning off the Image and Sound
Press the AV-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
The projector’s power-saving function will work 10 seconds after the im-
age is turned off.
As a result, the lamp power will be reduced.
NOTE:
• Even though the image is turned off, the menu still remains on the screen.
• Sound from the AUDIO OUT jack (Stereo mini) can be turned off.
• Even when the power-saving function works, the lamp power may be restored
to its original level temporarily.
• To restore the image, even if you press the AV-MUTE button immediately after
the start of the power-saving function, the lamp brightness may not be restored
to its original level.
Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
NOTE: The image is frozen but the original video is still playing back.
Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: The maximum magnification may be less than four times depending on
the signal.
To do so:
1. Press the D-ZOOM (+) button to magnify the picture.
To move the magnified image, use the ,, or button.
26
3. Convenient Features
2. Press the button.
The area of the magnified image will be moved
3. Press the D-ZOOM (−) button.
Each time the D-ZOOM (−) button is pressed, the image is reduced.
NOTE:
• The image will be enlarged or reduced at the center of the screen.
• Displaying the menu will cancel the current magnification.
Changing Eco Mode/Checking Energy-Saving Effect
Using Eco Mode [ECO MODE]
The ECO MODE (NORMAL and ECO) increases lamp life, while lowering power consumption and cutting down on
CO2 emissions.
Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL] and [ECO] modes.
[ECO MODE]
[OFF]
Description
Status of LAMP indicator
Off
The lamp brightness is 100%.
[AUTO ECO]
Lamp power consumption will be changed between
[OFF] and [NORMAL] automatically according to
picture level
NOTE: A bright gradation may be less visible depending
on the image.
[NORMAL]
[ECO]
Lamp power consumption. (approx.80% brightness
on M311X/M271X/M271W and approx. 75% on
M361X/M311W)The lamp life will extend by lowering
the lamp power.
Steady Green
light
Lamp power consumption (approx. 60% brightness).
The lamp life will extend longer than the one on
NORMAL mode by controlling power appropriate for
the lamp. The maximum power becomes equivalent
to the power in NORMAL.
To turn on the [ECO MODE], do the following:
1. Press the ECO Button on the remote control to display [ECO MODE] screen.
2. Press the ECO button again to select a mode you wish.
•
Each time the ECO button is pressed, the choices will be changed:
OFF → AUTO ECO → NORMAL → ECO → OFF
TIP:
• The leaf symbol at the bottom of the menu shows the current selection of ECO mode.
27
3. Convenient Features
NOTE:
• The [ECO MODE] can be changed by using the menu.
Select [SETUP] → [GENERAL] → [ECO MODE].
• The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] →[USAGE TIME].
• The projector is always in [NORMAL] for 90 seconds after the lamp is turned on and while the POWER indicator is blinking green.
The lamp condition will not be affected even when [ECO MODE] is changed.
• After a lapse of 1 minute from when the projector displays no-signal guidance, a blue, black or logo screen, [ECO MODE] will
automatically switch to [ECO].
• If the projector is overheated in [OFF] mode, there may be a case where the [ECO MODE] automatically changes to [NORMAL]
mode to protect the projector. When the projector is in [NORMAL] mode, the picture brightness decreases. When the projector
comes back to normal temperature, the [ECO MODE] returns to [OFF] mode.
Thermometer symbol [ ] indicates the [ECO MODE] is automatically set to [NORMAL] mode because the internal temperature
is too high.
Checking Energy-Saving Effect [CARBON METER]
This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector’s [ECO MODE]
is set to [AUTO ECO], [NORMAL], or [ECO]. This feature is called as [CARBON METER].
There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The [TOTAL CARBON
SAVINGS] message shows the total amount of CO2 emission reduction from the time of shipment up to now.You can
The [CARBON SAVINGS-SESSION] message shows the amount of CO2 emission reduction between the time of
changing to ECO MODE immediately after the time of power-on and the time of power-off. The [CARBON SAVINGS-
SESSION] message will be displayed in the [POWER OFF/ ARE YOU SURE?] message at the time of power-off.
TIP:
• The formula as shown below is used to calculate the amount of CO2 emission reduction.
Amount of CO2 emission reduction = (Power consumption in OFF for ECO MODE − Power consumption in AUTO ECO/NORMAL/
ECO for ECO MODE) × CO2 conversion factor.* When the image is turned off with the AV-MUTE button or with the lens cover
closed, the amount of CO2 emmission reduction will also increase.
* Calculation for amount of CO2 emission reduction is based on an OECD publication “CO2 Emissions from Fuel Combustion, 2008
Edition”.
• The [TOTAL CARBON SAVINGS] is calculated based on savings recorded in 15 minutes intervals.
• This formula will not apply to the power consumption which is not affected by whether [ECO MODE] is turned on or off.
28
3. Convenient Features
Preventing the Unauthorized Use of the Projector [SECURITY]
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro-
jector cannot project an image.
• The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu.
To enable the Security function:
1. Press the MENU button.
The menu will be displayed.
2. Press the button twice to select [SETUP] and press the button or the ENTER button to select [GEN-
ERAL].
3. Press the button to select [INSTALLATION].
4. Press the button three times to select [SECURITY] and press the ENTER button.
The OFF/ON menu will be displayed.
5. Press the button to select [ON] and press the ENTER button.
The [SECURITY KEYWORD] screen will be displayed.
6. Type in a combination of the four buttons and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length.
The [CONFIRM KEYWORD] screen will be displayed.
29
3. Convenient Features
7. Type in the same combination of buttons and press the ENTER button.
The confirmation screen will be displayed.
8. Select [YES] and press the ENTER button.
The SECURITY function has been enabled.
To turn on the projector when [SECURITY] is enabled:
1. Press the POWER button.
The projector will be turned on and display a message to the effect that the projector is locked.
2. Press the MENU button.
3. Type in the correct keyword and press the ENTER button. The projector will display an image.
NOTE: The security disable mode is maintained until the main power is turned off or unplugging the power cord.
30
3. Convenient Features
To disable the SECURITY function:
1. Press the MENU button.
The menu will be displayed.
2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button.
The OFF/ON menu will be displayed.
3. Select [OFF] and press the ENTER button.
The SECURITY KEYWORD screen will be displayed.
4. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the SECURITY function will be disabled.
NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request
code. Your request code is displayed in the Keyword Confirmation screen. In this example [NB52-YGK8-2VD6-K585-JNE6-EYA8]
is a request code.
31
3. Convenient Features
Using the Computer Cable (VGA) to Operate the
Projector (Virtual Remote Tool)
Using the utility software “Virtual Remote Tool” included on the companion NEC Projector CD-ROM, Virtual Remote
screen (or toolbar) can be displayed on your computer screen.
This will help you perform operations such as projector’s power on or off and signal selection via the computer cable
(VGA), serial cable, or LAN connection. Only via serial or LAN connection it is also used to send an image to the
projector and register it as the logo data of the projector. After registering it, you can lock the logo to prevent it from
changing.
Control Functions
Power On/Off, signal selection, picture freeze, picture mute, audio mute*, Logo transfer to the projector, and remote
control operation on your PC.
Virtual Remote screen
Toolbar
This section provides an outline of preparation for use of Virtual Remote Tool.
TIP:
• Virtual Remote Tool can be used with a LAN and a serial connection. USB connection is not supported by Virtual Remote Tool.
• For update information on Virtual Remote Tool, visit our website:
32
3. Convenient Features
NOTE:
• When [COMPUTER 1] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well
as your computer screen.
• Use the supplied computer cable (VGA) to connect the COMPUTER 1 IN connector directly with the monitor output connector of
the computer to use Virtual Remote Tool.
Using a switcher or other cables than the supplied computer cable (VGA) may cause failure in signal communication.
VGA cable connector:
Pin Nos. 12 and 15 are required for DDC/CI.
• Virtual Remote Tool may not work depending on your computer’s specifications and version of graphic adapters or drivers.
• To run Virtual Remote Tool on Windows XP Home Edition and Windows XP Professional, “Microsoft .NET Framework Version
2.0 or later” is required. The Microsoft .NET Framework Version 2.0 or later is available from Microsoft’s web page. Download
and install the it on your computer.
• Logo data (graphics) that can be sent to the projector with Virtual Remote Tool has the following restrictions:
(Only via serial or LAN connection)
- File size: Less than 1 MB
- Image size (resolution):
M361X/M311X/M271X: Horizontal 1024 × vertical 768 dots or less
M311W/M271W: Horizontal 1280 × vertical 800 dots or less
- Number of colors: 256 colors or less
TIP:
• The projector’s COMPUTER 1 IN connector supports DDC/CI (Display Data Channel Command Interface). DDC/CI is a standard
interface for bidirectional communication between display/projector and computer.
Step 1: Install Virtual Remote Tool on the computer
NOTE:
• To install Virtual Remote Tool, the Windows user account must have “Administrator” privilege (Windows 7, Windows Vista and
Windows XP).
• Exit all running programs before installing Virtual Remote Tool. If another program is running, the installation may not be com-
pleted.
1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.
The menu window will be displayed.
33
3. Convenient Features
TIP:
If the menu window will not be displayed, try the following procedure.
For Windows 7
1. Click “start” on Windows.
2. Click “All Programs” → “Accessories” → “Run”.
3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\
LAUNCHER.EXE)
4. Click “OK”.
The menu window will be displayed.
2 Click “Install Virtual Remote Tool” on the menu window.
The installation will start.
When the installation is complete, the Welcome window will be displayed.
3 Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
Read “END USER LICENSE AGREEMENT” carefully.
4 If you agree, click “I accept the terms in the license agreement” and then click “Next”.
•
•
Follow the instructions on the installer screens to complete the installation.
When the installation is complete, you will return to the menu window.
34
3. Convenient Features
TIP:
Uninstalling Virtual Remote Tool
Preparation:
Exit Virtual Remote Tool before uninstalling. To uninstall Virtual Remote Tool, the Windows user account must have
“Administrator” privilege (Windows 7 and Windows Vista) or “Computer Administrator” privilege (Windows XP).
• For Windows 7/Windows Vista
1 Click “Start” and then “Control Panel”.
The Control Panel window will be displayed.
2 Click “Uninstall a program” under “Programs”
The “Programs and Features” window will be displayed.
3 Select Virtual Remote Tool and click it.
4 Click “Uninstall/Change” or “Uninstall”.
• When the “User Account Control” windows is displayed, click “Continue”.
Follow the instructions on the screens to complete the uninstallation.
• For Windows XP
1 Click “Start” and then “Control Panel”.
The Control Panel window will be displayed.
2 Double-click “Add / Remove Programs”.
The Add / Remove Programs window will be displayed.
3 Click Virtual Remote Tool from the list and then click “Remove”.
Follow the instructions on the screens to complete the uninstallation.
Step 2: Connect the projector to the computer
1 Use the supplied computer cable (VGA) to connect the COMPUTER 1 IN connector of the projector directly
with the monitor output connector of the computer.
2 Connect the supplied power cord to the AC IN of the projector and the wall outlet.
The projector is in the standby condition.
Supplied computer cable (VGA)
COMPUTER 1 IN
AC Input
→ To wall outlet
Power cord (supplied)
TIP:
• When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed to navigate your connections.
35
3. Convenient Features
Step 3: Start Virtual Remote Tool
Start using the shortcut icon
•
Double-click the shortcut icon
on the Windows Desktop.
Start from the Start menu
•
Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual RemoteTool]
→ [Virtual Remote Tool].
When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
Follow the instructions on the screens
When “Easy Setup” is completed, the Virtual Remote Tool screen will be displayed.
NOTE:
• When [POWER-SAVING] is selected for [STANDBY MODE] from the menu, the projector cannot be turned on via the computer
cable (VGA) or network (wired LAN/wireless LAN) connection.
TIP:
• The Virtual Remote Tool screen (or Toolbar) can be displayed without displaying “Easy Setup” window.
To do so, click to place a check mark for “ Do not use Easy Setup next time” on the screen at Step 6 in “Easy Setup”.
36
3. Convenient Features
Exiting Virtual Remote Tool
1 Click the Virtual Remote Tool icon
The pop-up menu will be displayed.
on the Taskbar.
2 Click “Exit”.
The Virtual Remote Tool will be closed.
Viewing the help file of Virtual Remote Tool
• Displaying the help file using the taskbar
1 Click the Virtual Remote Tool icon
on the taskbar when Virtual Remote Tool is running.
The pop-up menu will be displayed.
2. Click “Help”.
The Help screen will be displayed.
• Displaying the help file using the Start Menu.
1. Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “Virtual Remote
Tool” → and then “Virtual Remote Tool Help” in this order.
The Help screen will be displayed.
37
3. Convenient Features
Operating Your Computer’s Mouse Functions from the
Projector’s Remote Control via the USB Cable (Remote Mouse
Function)
The built-in remote mouse function enables you to operate your computer’s mouse functions from the supplied remote
control when the projector is connected to a computer via a commercially available USB cable (compatible with USB
2.0 specifications).
The Remote Mouse function works for the COMPUTER 1 or COMPUTER 2 input while the computer screen is dis-
played.
The Remote Mouse function will not work while you freeze or magnify an image.
-
Using the USB cable to connect the projector and the computer will also start USB Display function.
USB (PC)
USB cable (not supplied)
NOTE:
• A USB cable must support the USB 2.0 Specifications.
• The mouse function can be used with the following operating systems:
Windows 7, Windows XP, or Windows Vista
• In SP2 or older version of Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
• Wait at least 5 seconds after disconnecting the USB cable before reconnecting it and vice versa. The computer may not identify
the USB cable if it is repeatedly connected and disconnected in rapid intervals.
• Connect the projector to the computer with a USB cable after starting the computer. Failure to do so may fail to start the com-
puter.
Operating your computer’s mouse from the remote control
You can operate your computer’s mouse from the remote control.
PAGE / Button ���������������������������scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint
on your computer�
Buttons������������������������������moves the mouse cursor on your computer�
MOUSE L-CLICK/ENTER Button ������works as the mouse left button�
MOUSE R-CLICK Button������������������works as the mouse right button�
NOTE:
• When you operate the computer using the or button with the menu displayed, both the menu and the mouse pointer
will be affected. Close the menu and perform the mouse operation.
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user
documentation or online help supplied with your computer.
38
3. Convenient Features
Projecting Your Computer’s Screen Image from the
Projector via the USB Cable (USB Display)
Using a commercially available USB cable (compatible with USB 2.0 specifications) to connect the computer with the
projector allows you to send your computer screen image to the projector for displaying. Power On/Off and source
selection of the projector can be done from your computer without connecting a computer cable (VGA).
NOTE:
• To make USB DISPLAY available on Windows XP, the Windows user account must have “Administrator” privilege.
• USB Display uses functions of Image Express Utility Lite contained on NEC Projector CD-ROM (→ page 52).
Starting USB Display, however, will not install Image Express Utility Lite on your computer. This is because USB Display executes
the projector’s program only.
• When USB Display is used, the sound is output from the COMPUTER 2 AUDIO IN Mini Jack (Stereo Mini). Image and sound may
not be synchronized.
1. Start the computer.
2. Connect the projector’s power cord to the wall outlet and put the projector into standby condition.
•
Open the projector’s lens cover.
3. Use the USB cable to connect the computer with the projector.
USB cable (not supplied)
USB (PC)
→ To wall outlet
Power cord (supplied)
The message “The projector is in standby mode. Connect it?” will be displayed on the computer screen.
The control window of Image Express Utility Lite will be displayed on the top of the screen.
•
NOTE: Depending on the computer setting, the “AutoPlay” window may be displayed when the
computer detects the connection to the projector. If this happens, click the “Start USB Display”
window.
4. Click “Yes”.
The projector will turn on and the message “The projector is getting ready. Please wait.” will be displayed on the
computer screen. This message will disappear in a few seconds.
39
3. Convenient Features
5. Operate the control window.
(6)
(1) (2) (3) (4) (5)
(1)
(2)
(3)
(4)
(Source)����� Selects an input source of the projector�
(Picture) ���� Turns on or off AV-MUTE (Picture mute), and turns on or off FREEZE (Freeze a picture)�
(Sound) ����� Turns on or off AV-MUTE (Sound mute), play the sound and turns up or down the volume�
(Others)����� Uses “Update”, “HTTP Server”*, “Settings” and “Information”�
* The HTTP Server cannot be selected when a USB cable is connected�
(5)
(Exit)���������� Exit Image Express Utility Lite� You can also turn off the projector at the same time�
(6) (Help)����������� Displays the help of Image Express Utility Lite�
40
3. Convenient Features
Controlling the Projector by Using an HTTP Browser
Overview
The HTTP Server function provides settings and operations for:
1. Setting for wired/wireless network (NETWORK SETTINGS)
To use wired/wireless LAN connection, connect the projector to the computer with a commercially available LAN
2. Setting Alert Mail (ALERT MAIL)
When the projector is connected to a wired/wireless network, lamp replace time or error messages will be sent via
e-mail.
3. Operating the projector
Power on/off, selecting input, volume control and picture adjustments are possible.
4. Setting PJLink PASSWORD and AMX BEACON
This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting
method will vary depending on the version of browser. Please refer to the help files and the other information provided
in your software.
Two ways of access to the HTTP server function are available:
•
Start the Web browser on the computer via the network connected to the projector and enter the following
URL :
http://<the projector’s IP address> /index.html
•
Use Image Express Utility Lite contained on the supplied NEC Projector CD-ROM.
TIP: The factory setting IP address is [DHCP ON].
NOTE:
• To use the projector in a network, consult with your network administrator about network settings.
• The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your net-
work.
Should this happen, consult your network administrator. The projector may not respond if its buttons are repeatedly pressed in
rapid intervals. Should this happen, wait a moment and repeat. If you still can’t get any response, turn off and back on the projec-
tor.
• If the PROJECTOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to refresh your web
browser (or clear the cache).
Preparation before Use
Connect the projector to a commercially available LAN cable before engaging in browser operations. (→ page 110)
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the
setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set
will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be
reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.
41
3. Convenient Features
Handling of the Address for Operation via a Browser
Regarding the actual address that is entered for the address or entered to the URL column when operation of the pro-
jector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the
projector has been registered to the domain name server by a network administrator, or the host name corresponding
to the IP address of the projector has been set in the “HOSTS” file of the computer being used.
Example 1: When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network
setting by specifying
http://pj.nec.co.jp/index.html
for the address or the entry column of the URL.
Example 2: When the IP address of the projector is “192.168.73.1”, access is gained to the network setting by
specifying
http://192.168.73.1/index.html
for the address or the entry column of the URL.
PROJECTOR ADJUSTMENT
POWER: This controls the power of the projector.
ON ������������������������� Power is switched on�
OFF ������������������������ Power is switched off�
VOLUME: This controls the volume of the projector.
��������������������������� Increases the volume adjustment value�
��������������������������� Decreases the volume adjustment value�
AV-MUTE: This controls the mute function of the projector.
PICTURE ON���������� Mutes the video�
PICTURE OFF��������� Cancels the video muting�
SOUND ON ������������ Mutes the audio�
SOUND OFF ����������� Cancels the audio muting�
ALL ON������������������ Mutes each of the video, and audio functions�
ALL OFF����������������� Cancels the muting of each of the video, and audio functions�
42
3. Convenient Features
PICTURE: Controls the video adjustment of the projector.
BRIGHTNESS ���� Increases the brightness adjustment value�
BRIGHTNESS ���� Decreases the brightness adjustment value�
CONTRAST �������� Increases the contrast adjustment value�
CONTRAST �������� Decreases the contrast adjustment value�
COLOR �������������� Increases the color adjustment value�
COLOR �������������� Decreases the color adjustment value�
HUE ������������������� Increases the hue adjustment value�
HUE ������������������� Decreases the hue adjustment value�
SHARPNESS ����� Increases the sharpness adjustment value�
SHARPNESS ����� Decreases the sharpness adjustment value�
•
The functions that can be controlled will vary depending on the signal being input to the projector. (→ page
78)
SOURCE SELECT: This switches the input connector of the projector.
COMPUTER 1 �������� Switches to the COMPUTER 1 IN connector�
COMPUTER 2 �������� Switches to the COMPUTER 2 IN connector�
HDMI��������������������� Switches to the HDMI IN connector�
VIDEO�������������������� Switches to the VIDEO IN connector�
S-VIDEO ���������������� Switches to the S-VIDEO IN connector�
VIEWER����������������� Switches to the data on the USB memory device�
NETWORK ������������� Switches to a LAN signal�
USB DISPLAY�������� Switches to the USB Port (PC)�
PROJECTOR STATUS: This displays the condition of the projector.
LAMP LIFE REMAINING �����Displays the remaining life of the lamp as a percentage�
LAMP HOURS USED�����������Displays how many hours the lamp has been used�
FILTER HOURS USED���������Displays how many hours the filter has been used�
ERROR STATUS������������������Displays the status of errors occurring within the projector�
LOG OFF: Logging off your projector and returning to the authentication screen (LOGON screen).
43
3. Convenient Features
NETWORK SETTINGS
• SETTINGS
WIRED or WIRELESS
SETTING
Set for wired LAN or for wireless LAN.
APPLY
Apply your settings to wired LAN or wireless LAN.
DHCP ON
Automatically assign IP address, subnet mask, and gateway to the projector from your
DHCP server.
DHCP OFF
Set IP address, subnet mask, and gateway to the projector assigned by your network
administrator.
IP ADDRESS
SUBNET MASK
GATEWAY
Set your IP address of the network connected to the projector.
Set your subnet mask number of the network connected to the projector.
Set the default gateway of the network connected to the projector.
AUTO DNS ON
DHCP server will automatically assign IP address of DNS server connected to the
projector.
AUTO DNS OFF
Set your IP address of DNS server connected to the projector.
Setting for WIRED LAN
ENABLE
Turn on wired LAN connection
Turn off wired LAN connection
DISABLE
Setting for WIRELESS LAN (with the optional USB Wireless LAN Unit equipped)
EASY CONNECTION
CHANNEL
Execute a wireless LAN using EASY CONNECTION.
Select a channel. Available channels vary depending on the country and region.When
you select [INFRASTRUCTURE], make sure that the projector and your access point
are on the same channel; when you select [AD HOC], make sure that the projector and
your computer are on the same channel.
PROFILE 1/PROFILE 2
SSID
Two settings can be set for wireless LAN connection. Select PROFILE 1 or PROFILE
2.
Enter an identifier (SSID) for wireless LAN. Communication can be done only with
equipment whose SSID matches SSID for your wireless LAN.
SITE SURVEY
Displays a list of available SSIDs for wireless LAN on site. Select an SSID which you
can access.
44
3. Convenient Features
NETWORK TYPE
SECURITY TYPE
Select communication method when using wireless LAN.
INFRASTRUCTURE: Select this option when communicating with one or more equip-
ment connected to the wireless LAN network via a wireless access point.
AD HOC: Select this option when using the wireless LAN to directly communicate with
a computer in peer-to-peer mode.
Turn on or off the encryption mode for secure transmission. When turn on the encryp-
tion mode, set WEP key or encrypted key.
DISABLE
Will not turn on the encryption feature. Your communications
may be monitored by someone.
WEP 64 bit
Uses 64-bit datalength for secure transmission.
WEP 128 bit
Uses 128-bit datalength for secure transmission.This option will
increase privacy and security when compared to use of 64-bit
datalength encryption.
WPA PSK-TKIP/
WPA PSK-AES/
WPA2 PSK-TKIP/
WPA2 PSK-AES
These options provide stronger security than WEP.
NOTE:
• The WEP settings must be the same as communication devices such as PC or access point in
your wireless network.
• When you use WEP, your image transmission speed will slow down.
• [WPA PSK-TKIP], [WPA PSK-AES], [WPA2 PSK-TKIP] and [WPA2 PSK-AES] are not available
when [AD HOC] is selected from [NETWORK TYPE].
INDEX
KEY
Select encryption key when selecting [WEP 64 bit] or [WEP 128 bit] in [SECURITY
TYPE].
When selecting [WEP 64 bit] or [WEP 128 bit] in [SECURITY TYPE]:
Enter WEP key.
Select
Characters (ASCII)
Up to 5 characters
Up to 13 characters
Hexadecimal digit (HEX)
Up to 10 characters
Up to 26 characters
WEP 64 bit
WEP 128 bit
When selecting [WPA PSK-TKIP], [WPA PSK-AES], [WPA2 PSK-TKIP] or [WPA2
PSK-AES]:
Enter encryption key. Key length must be 8 or greater and 63 or less.
• NAME
PROJECTOR NAME
Enter a name for your projector so that your computer can identify the projector. A
projector name must be 16 characters or less.
TIP: Projector name will not be affected even when [RESET] is done from the menu.
HOST NAME
Enter the hostname of the network connected to the projector. A host name must be
15 or less.
DOMAIN NAME
Enter the domain name of the network connected to the projector. A domain name
must be 60 characters or less.
45
3. Convenient Features
• ALERT MAIL
ALERT MAIL (English
only)
This option will notify your computer of lamp replace time or error messages via e-mail
when using wireless or wired LAN.
Placing a checkmark will turn on the Alert Mail feature.
Clearing a checkmark will turn off the Alert Mail feature.
Sample of a message to be sent from the projector:
The lamp and filters are at the end of its usable life. Please replace the lamp and
filters.
Projector Name: NEC Projector
Lamp Hours Used: 100 [H]
SENDER’S ADDRESS
SMTP SERVER NAME
Enter sender’s address.
Enter the SMTP server name to be connected to the projector.
RECIPIENT’S ADDRESS Enter your recipient’s address. Up to three addresses can be entered.
1,2,3
TEST MAIL
Send a test mail to check whether your settings are correct or not
NOTE:
• If you execute a test, you may not receive an Alert mail. Should this happen, check if network
settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert mail. Should this
happen, check if the Recipient’s Address is correct.
SAVE
Click this button to reflect the above settings.
• NETWORK SERVICE
PJLink PASSWORD
Set a password for PJLink*. A password must be 32 characters or less. Do not forget
your password. However, if you forget your password, consult with your dealer.
HTTP PASSWORD
AMX BEACON
Set a password for HTTP server. A password must be 10 characters or less.
Turn on or off for detection from AMX Device Discovery when connecting to the network
supported by AMX’s NetLinx control system.
TIP:
When using a device that supports AMX Device Discovery, all AMX NetLinx control system will rec-
ognize the device and download the appropriate Device Discovery Module from an AMX server.
Placing a checkmark will enable detecting the projector from AMX Device Discovery.
Clearing a checkmark will disable detecting the projector from AMX Device Discovery.
*What is PJLink?
PJLink is a standardization of protocol used for controlling projectors of different manufacturers.This standard proto-
col is established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.
The projector supports all the commands of PJLink Class 1.
Setting of PJLink will not be affected even when [RESET] is done from the menu.
CRESTRON ROOMVIEW compatibility
The projector supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed
and controlled from a computer or a controller.
For more information, visit http://www.crestron.com
<Setting Procedure>
Access to the HTTP server function, and make necessary settings for [CRESTRON] in [NETWORK SETTINGS].
46
3. Convenient Features
• ROOMVIEW for managing from the computer.
DISABLE
ENABLE
Disables ROOMVIEW.
Enables ROOMVIEW.
• CRESTRON CONTROL for managing from the controller.
DISABLE
ENABLE
IP ADDRESS
IP ID
Disables CRESTRON CONTROL.
Enables CRESTRON CONTROL.
Set your IP address of CRESTRON SERVER.
Set your IP ID of CRESTRON SERVER.
TIP: The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.
For more information, visit http://www.crestron.com
• INFORMATION
WIRED LAN
WIRELESS LAN
UPDATE
Display a list of settings of wired LAN connection.
Display a list of settings of wireless LAN connection.
Reflect settings when they are changed.
47
3. Convenient Features
Controlling the Projector over a LAN (PC Control Utility Pro 4/
Pro 5)
Using the utility software “PC Control Utility Pro 4” and “PC Control Utility Pro 5” included on the companion NEC
Projector CD-ROM, the projector can be controlled from a computer over a LAN.
PC Control Utility Pro 4 is a program compatible with Windows. (→ this page)
Control Functions
Power On/Off, signal selection, picture freeze, picture mute, audio mute, adjusting, error message notification, event
schedule.
Screen of PC Control Utility Pro 4
This section provides an outline of preparation for use of PC Control Utility Pro 4/Pro 5. For information on how to use
Step 1: Install PC Control Utility Pro 4/Pro 5 on the computer.
Step 2: Connect the projector to a LAN.
Step 3: Start PC Control Utility Pro 4/Pro 5.
• To run PC Control Utility Pro 4 on Windows XP Home Edition and Windows XP Professional, “Microsoft .NET
Framework Version 2.0 or later” is required. The Microsoft .NET Framework Version 2.0 or later is available from
Microsoft’s web page. Download and install the it on your computer.
TIP:
• PC Control Utility Pro 4 can be used with a serial connection.
Using on Windows
Step 1: Install PC Control Utility Pro 4 on the computer
NOTE:
• To install or uninstall the program, the Windows user account must have [Administrator] privilege (Windows 7, Windows Vista
and Windows XP)
• Exit all running programs before installation. If another program is running, the installation may not be completed.
1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.
The menu window will be displayed.
48
3. Convenient Features
TIP:
If the menu window will not be displayed, try the following procedure.
For Windows 7:
1. Click “start” on Windows.
2. Click “All Programs” → “Accessories” → “Run”.
3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\
LAUNCHER.EXE)
4. Click “OK”.
the menu window will be displayed.
2 Click “PC Control Utility Pro 4” on the menu window.
The installation will start.
When the installation is complete, the Welcome window will be displayed.
3 Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
Read “END USER LICENSE AGREEMENT” carefully.
4 If you agree, click “I accept the terms in the license agreement” and then click “Next”.
•
•
Follow the instructions on the installer screens to complete the installation.
When the installation is complete, you will return to the menu window.
TIP:
• Uninstalling PC Control Utility Pro 4
To uninstall PC Control Utility Pro 4, do the same procedures stated as in “Uninstalling Virtual Remote Tool”. Read “Virtual Remote
49
3. Convenient Features
Step 2: Connect the projector to a LAN.
Connect the projector to the LAN by following the instructions in “Connecting to a Wired LAN” (→ page 110), “Con-
necting to a Wireless LAN (Optional: NP02LM series)” (→ page 111) and “9. Controlling the Projector by Using an
Step 3: Start PC Control Utility Pro 4
Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” →
“PC Control Utility Pro 4”.
NOTE:
• For the Schedule function of the PC Control utility Pro 4 to work, you must have your computer running and not in standby/
sleep mode. Select “Power Options” from the “Control Panel” in Windows and disable its standby/sleep mode before running the
scheduler.
[Example] For Windows 7:
Select “Control Panel” → “System and Security” → “Power Options” → “Change when the computer sleeps” → “Put the computer
to sleep” → “Never”.
NOTE:
• When [POWER-SAVING] is selected for [STANDBY MODE] from the menu, the projector cannot be turned on via the network
(wired LAN/wireless LAN) connection.
TIP:
Viewing the Help of PC Control Utility Pro 4
•
Displaying the Help file of PC Control Utility Pro 4 while it is running.
Click “Help (H)” → “Help (H) …” of window of PC Control Utility Pro 4 in this order.
The pop-up menu will be displayed.
•
Displaying the help file using the Start Menu.
Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” →
“PC Control Utility Pro 4 Help”.
The Help screen will be displayed.
50
3. Convenient Features
Using on Mac OS
Step 1: Install PC Control Utility Pro 5 on the computer
1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive.
The CD-ROM icon will be displayed on the desktop.
2. Double-click the CD-ROM icon.
The CD-ROM window will be displayed.
3. Double-click the “Mac OS X” folder.
4. Double-click “PC Control Utility.mpkg”.
The installer will start.
5. Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
6. Read “END USER LICENSE AGREEMENT” and click “Next”.
The confirmation window will be displayed
7. Click “I accept the terms in the license agreement”.
Follow the instructions on the installer screens to complete the installation.
Step 2: Connect the projector to a LAN
Connect the projector to the LAN by following the instructions in “Connecting to a Wired LAN” (→ page 110), “Con-
necting to a Wireless LAN (Optional: NP02LM series)” (→ page 111) and “❾ Controlling the Projector by Using an
Step 3: Start PC Control Utility Pro 5
1. Open your Applications folder in Mac OS.
2. Click the “PC Control Utility Pro 5” folder.
3. Click the “PC Control Utility Pro 5” icon.
PC Control Utility Pro 5 will start.
NOTE:
• For the Schedule function of the PC Control utility Pro 5 to work, you must have your computer running and not in sleep mode.
Select “Energy Saver” from the “System Preferences” in Mac and disable its sleep mode before running the scheduler.
• When [POWER-SAVING] is selected for [STANDBY MODE] from the menu, the projector cannot be turned on via the network
(wired LAN/wireless LAN) connection.
TIP:
Viewing the Help of PC Control Utility Pro 5
• Displaying the Help file of PC Control Utility Pro 5 while it is running.
•
From the menu bar, click “Help” → “Help” in this order.
The Help screen will be displayed.
• Displaying the Help using the Dock
1. Open “Application Folder” in Mac OS.
2. Click the “PC Control Utility Pro 5” folder.
3. Click the “PC Control Utility Pro 5 Help” icon.
The Help screen will be displayed.
51
3. Convenient Features
Projecting Your Computer’s Screen Image from the
Projector over a LAN (Image Express Utility Lite)
Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM allows you to send the computer’s
screen image to the projector over a USB cable or a wired or wireless LAN.
Image Express Utility Lite is a program compatible with Windows.
This section will show you an outline about how to connect the projector to a LAN and to use Image Express Utility
Lite. For the operation of Image Express Utility Lite, see the help of Image Express Utility Lite.
Step 1: install Image Express Utility Lite on the computer.
Step 2: Connect the projector to a LAN.
Step 3: Start Image Express Utility Lite.
TIP:
• Image Express Utility Lite (for Windows) can be started from most commercially available removable media such as USB memory
What You can Do with Image Express Utility Lite
• Image transmission (for Windows and Mac OS)
•
•
•
The screen of your computer can be sent to the projector via a wired or wireless network without a computer cable
(VGA).
By using “EASY CONNECTION” function, the complicated network settings can be simplified and the computer
will automatically connect to the projector.
The screen of your computer can be sent to up to four projectors at the same time.
• USB Display (for Windows only)
•
•
Computer’s screen image can be projected via a USB cable, without connecting a computer cable (VGA).
Just connecting the computer and the projector over a USB cable will make the USB Display function available
• Geometric Correction Tool [GCT] (for Windows only)
See “⓬ Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite)”.
NOTE:
• When Image Express Utility Lite is used, the audio from the COMPUTER 2 AUDIO IN Mini Jack (Stereo Mini) may not be synchro-
nized with the video.
Using on Windows
Step 1: install Image Express Utility Lite on the computer.
NOTE:
• To install or uninstall the program, the Windows user account must have “Administrator” privilege (Windows 7, Windows Vista
and Windows XP).
• Exit all running programs before installation. If another program is running, the installation may not be completed.
• Image Express Utility Lite will be installed to the system drive of your computer.
If the message “There is not enough free space on destination” is displayed, free up enough space (about 100 MB) to install the
program.
1. Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.
The menu window will be displayed.
52
3. Convenient Features
TIP:
If the menu window will not be displayed, try the following procedure.
For Windows 7:
1. Click “start” on Windows.
2. Click “All Programs” → “Accessories” → “Run”.
3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\
LAUNCHER.EXE)
4. Click “OK”.
The menu window will be displayed.
2. Click “Installing Image Express Utility Lite” on the menu window.
The installation will start.
“END USER LICENSE AGREEMENT” screen will be displayed.
Read “END USER LICENSE AGREEMENT” carefully
3. If you agree, click “I agree.” and then click “Next”.
•
•
Follow the instructions on the installer screens to complete the installation.
When the installation is complete, you will return to the menu window.
When the installation is complete, a completion message will be displayed.
4. Click “OK”.
This completes the installation.
TIP:
• Uninstalling Image Express Utility Lite
To uninstall Image Express Utility Lite, do the same procedures stated as in “Uninstalling Virtual Remote Tool”. Read “Virtual Remote
Step 2: Connect the projector to a LAN.
Connect the projector to the LAN by following the instructions in “Connecting to a Wired LAN” (→ page 110), “Con-
necting to a Wireless LAN (Optional: NP02LM series)” (→ page 111) and “9. Controlling the Projector by Using an
Step 3: Start Image Express Utility Lite.
1. OnWindows, click“Start”→“All programs”→“NEC Projector UserSupportware”→“Image Express Utility
Lite” → “Image Express Utility Lite”.
Image Express Utility Lite will start.
The select window for network connection will be displayed
2. Select Network and click “OK”.
The select window for destination will show a list of connectable projectors.
•
When connecting the computer directly to the projector by one-to-one, “Easy Connection” is recommended.
•
•
When one or more networks for “EASY CONNECTION” are found, the “Easy Connection Selection Screen”
window will be displayed.
To check for the network available for connected projectors, from the menu, select [INFO.] → [WIRELESS
LAN] → [SSID].
53
3. Convenient Features
3. Select the network you wish to connect, and click “Select”.
The target selection window will be displayed.
4. Place a check mark for projectors to be connected, and then click “Connect”.
•
When one or more projectors are displayed, from the menu on the projector, select [INFO.] → [WIRELESS LAN]
→ [IP ADDRESS].
When connecting with the projector is established, you can operate the control window to control the projector. (→
NOTE:
• When [POWER-SAVING] is selected for [STANDBY MODE] from the menu, the projector that is turned off will not be displayed
in the select window for destination
TIP:
Viewing the “Help” file of Image Express Utility Lite
•
•
•
Displaying the Help file of Image Express Utility Lite while it is running.
Click the [?] (help) icon on the control window.
The Help screen will be displayed.
Displaying the Help file of GCT while it is running.
Click “Help” → “Help” on the edit window.
The Help screen will be displayed.
Displaying the help file using the Start Menu.
Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “Image Express Utility Lite”
→ “Image Express Utility Lite Help”.
The Help screen will be displayed.
54
3. Convenient Features
Starting Image Express Utility Lite from a USB Memory or SD Card
Image Express Utility Lite can be started from commercially available removable media such USB memory or SD cards
if it is copied beforehand. This will eliminate the trouble of installing Image Express Utility Lite to your computer.
1. Copy Image Express Utility Lite to removable media.
Copy all the folders and files (total size approx. 6MB) from the “IEU_Lite (removable-media)” folder in the supplied
NEC Projector CD-ROM to the root directory of your removable media.
2. Insert your removable media into your computer.
The “AutoPlay” screen will be displayed on your computer.
TIP:
• If the “AutoPlay” screen is not displayed, open the folder from “Computer” (“My Computer” for Windows XP).
3. Click “Open folder to view files”
The IEU_Lite.exe, other folder, and files will be displayed.
4. Double-click the “IEU_Lite.exe” (
) icon.
Image Express Utility Lite will start.
NOTE:
• The “EASY CONNECTION” function is not supported when Image Express Utility Lite is started from removable media.
55
3. Convenient Features
Using on Mac OS
Step 1: Install Image Express Utility Lite for Mac OS on the computer
1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive.
The CD-ROM icon will be displayed on the desktop.
2. Double-click the CD-ROM icon.
The CD-ROM window will be displayed.
3. Double-click the “Mac OS X” folder.
4. Double-click “Image Express Utility Lite.dmg”.
The “Image Express Utility Lite” window will be displayed.
5. Drag and drop the “Image Express Utility Lite” folder to your Applications folder in Mac OS.
Step 2: Connect the projector to a LAN
Connect the projector to the LAN by following the instructions in “Connecting to a Wired LAN” (→ page 110), “Con-
necting to a Wireless LAN (Optional: NP02LM series)” (→ page 111) and “❾ Controlling the Projector by Using an
Step 3: Start Image Express Utility Lite for Mac OS
1. Open your Applications folder in Mac OS.
2. Double-click the “Image Express Utility Lite” folder.
3. Double-click the “Image Express Utility Lite” icon.
When Image Express Utility Lite for Mac OS starts, the select window for destination will be displayed.
•
At the first time of startup, “END USER LICENSE AGREEMENT” screen will be displayed before the select
window for destination is displayed.
Read “END USER LICENSE AGREEMENT” and select “I accept the terms in the license agreement”, and click
“OK”.
4. Select a projector to be connected, and then click “Connect”.
Your desktop screen will be displayed on the projector.
TIP:
Viewing the Help of Image Express Utility Lite for Mac OS
•
From the menu bar, click “Help” → “Image Express Utility Lite Help” while Image Express Utility is run-
ning.
The Help screen will be displayed
56
3. Convenient Features
Projecting an Image from an Angle (Geometric Correction
Tool in Image Express Utility Lite)
The Geometric Correction Tool (GCT) function allows you to correct distortion of images projected even from an
angle.
What you can do with GCT
•
The GCT feature includes the following three functions
•
•
•
4-point Correction:You can fit a projected image within the border of the screen easily by align the four corners
of an image to the ones of the screen.
Multi-point Correction: You can correct a distorted image on the corner of a wall or irregular shaped screen
by using many separated screens to correct the image as well as 4-point Correction.
Parameters Correction: You can correct a distorted image by using a combination of transformational rules
prepared in advance.
This section will show an example for use with 4-point Correction.
For information about “Multi-point Correction” and “Parameters Correction”, see the help file of Image Express
•
•
Your correction data can be stored in the projector or your computer which can be restored when necessary.
The GCT function is available with a USB cable, wired or wireless LAN connection, and video cable.
Projecting an Image from an Angle (GCT)
This section will show an example for use with USB Display (using a USB cable to connect a computer and the pro-
jector).
•
The USB Display function will automatically display the control window
•
For a video cable or LAN connection, install and start Image Express Utility Lite in your computer beforehand. (→
Preparation: Adjust the projector position or the zoom so that the projected image can cover the whole screen area.
1. Click the “ ” (Picture) icon and then the “ ” button.
The “4-point Correction” window will be displayed.
2. Click the “Start Correction” button and then “Start 4-point Correction” button.
A green frame and a mouse pointer ( ) will be displayed.
Four [ • ] marks will be appeared at four corners of the green frame
•
57
3. Convenient Features
3. Use the mouse to click the [ • ] mark of which corner you wish to move.
The currently selected [ • ] mark will turn red.
(In the above example, Windows screens are omitted for clarification.)
4. Drag the selected [ • ] mark to the point you wish to correct and drop it.
•
When you click somewhere within the project image area, the nearest [ • ] mark will go to the position where
the mouse cursor is.
5. Repeat Step 3 and 4 to correct the distortion of the projected image.
6. After completing, right-click the mouse.
The green frame and the mouse pointer will disappear from the projected image area. This will complete the cor-
rection.
7. Click the “X” (close) button on the “4-point Correction” window.
The “4-point Correction” window will disappear and the 4-point correction will take effect.
8. Click the “
” button on the control window to exit the GCT.
TIP:
• After performing the 4-point correction, you can save the 4-point correction data to the projector by clicking “File” → “Export to
the projector…” on the “4-point Correction” window.
• See the Help of Image Express Utility Lite for operating “4-point Correction” window and other functions than GCT. (→ page 54,
56)
58
4. Using the Viewer
❶ What you can do with the Viewer
The Viewer has the following features.
•
When a commercially available USB memory that stores image files is inserted into the USB port (Type A) of the
projector, the Viewer allows you to view the image files on the USB memory.
Even if no computer is available, presentations can be conducted simply with the projector.
Supported graphic format is JPEG.
•
•
The Viewer displays the thumbnail screen (JPEG Exif only) on which you can jump to any specific image you wish
to project.
•
•
•
There are two ways of playback for slideshow: manual playback and auto playback. The interval time can be
changed in auto playback.
The order of displaying images can be set by name, date or size. Ascending or descending order can be se-
lected.
Images can be rotated by 90 degrees during playback.
59
4. Using the Viewer
NOTE
• The USB port of the projector does not support USB hub.
• The following operations by using the buttons on the projector are not possible when the VIEWER screen such as the slide screen
and the thumbnail screen is displayed.
- Keystone correction by using the ▲/▼ button
- Auto Adjustment by using the AUTO ADJ. button
- Volume control with the ◀ or ▶ button
To perform Keystone correction or Source selection during display of the Viewer, press the MENU button twice to display the
menu and operate Viewer from the menu.
• Freezing picture by using the FREEZE button on the remote control is not possible when the VIEWER screen such as the slide
screen and the thumbnail screen is displayed.
• Executing [RESET] → [ALL DATA] from the menu will return the settings for the Viewer toolbar to the factory default.
• USB memory
- Be sure to use a USB memory device formatted with the FAT32 or FAT16 file system.
The projector does not support NTFS formatted USB memory.
If the projector does not recognize your USB memory, check if the format is supported.
To format your USB memory in your computer, refer to the document or help file that comes with your Windows.
- We do not warrant that the USB port of the projector will support all USB memories in the market.
• Supported images
- Supported file format for Viewer are as follows.
We do not warrant all the images are supported for Viewer.
Images other than mentioned in the table may not be supported.
Image type
JPEG
Extension
Description
Baseline/Exif are supported
JPG/JPEG
- Slideshow, effect, and sound effect set with PowerPoint cannot be played back.
- Image can be displayed at a resolution up to 10000 × 10000 pixels.
- Even if images are met by the above conditions, there may be some images which cannot be played back.
- More than 200 icons (total number of image file icons and folder icons) cannot be displayed in a thumbnail screen.
- Long file/folder name will be limited to the specified length. This can be shown by bracket added.
- If one folder has many files, it takes some time to play back.
• If a single folder contains too many files, switching images will take time. To shorten switching time, reduce the number of images
contained in a single folder.
TIP: Exchangeable image file format (Exif) is a standard image file format used by digital cameras with the addition of specific
shooting data.
60
4. Using the Viewer
❷ Projecting images stored in a USB memory device
This section explains the basic operation of the Viewer.
The explanation provides the operational procedure when the Viewer toolbar (→ page 65) is set to the factory de-
fault.
- Starting the Viewer.......................................................................below
Preparation: Before starting the Viewer, store images to the USB memory using your computer.
Starting the Viewer
2. Insert the USB memory into the USB port of the projec-
I
tor.
•
Do not remove the USB memory from the projector while
it’s LED flashes. Doing so may corrupt the data.
3. Press the SOURCE button on the projector cabinet.
The Viewer start screen will be displayed.
•
Press the VIEWER button on the remote control.
61
4. Using the Viewer
4. Press the ENTER button.
5. Use the ▲▼◀ or ▶ button to select an icon.
•
The → (arrow) symbol on the right indicates there are more
pages. pressing the PAGE ▽ (page down) button will show
the next page: pressing the PAGE △ (page up) will show
the previous page.
6. Press the ENTER button.
The selected slide will be displayed.
•
When a folder icon is selected, icons contained in the folder
will be displayed.
7. Press the ▶ button to select the next slide.
The slide on the right will be displayed.
•
•
The ◀ or ▶ button can be used to select the next (right)
slide or the previous (left) slide in the thumbnail screen.
Pressing the MENU button during display of the thumbnail
screen, the slide screen, or the slideshow screen will display
the toolbar. The toolbar is used to select or rotate an slide.
8. Press the EXIT button when the toolbar is not dis-
played.
The thumbnail screen will be displayed.
•
•
Another way to display the thumbnail screen is to press the
ENTER button.
To close the toolbar, press the MENU button to return to the
SOURCE list, and press the MENU button again to close
the SOURCE list.
62
4. Using the Viewer
Removing the USB memory from the projector
1. Select the VIEWER start screen.
Press the EXIT button with no menu displayed.
2. Remove the USB memory from the projector.
Make sure that the LED on the USB memory is not flashing
before removing the USB memory.
NOTE: If you remove the USB memory from the projector with a slide
displayed, the projector may not operate correctly. If this happens,
turn off the projector and unplug the power cord. Wait 3 minutes, then
connect the power cord, and turn on the projector.
Exiting the Viewer
1. Press the MENU button with the slide screen or the
thumbnail screen displayed.
The control bar or the pop-up menu will be displayed.
2. Press the MENU button again.
The on-screen menu will be displayed.
3. Select a source other than [VIEWER] and press the
ENTER button.
The Viewer will be exited.
TIP: To exit the Viewer using the remote control, select a source other
than [VIEWER].
63
4. Using the Viewer
Parts of each screen
The Viewer has four screens.
(1) Viewer start screen
(3) Thumbnail screen
(6) (4)
(9) Slide screen/
(11) Slideshow screen
(5)
(7)
(2)
(8)
(10) (12)
Name
Description
(1) Viewer start screen
(2) USB icon
This screen will be displayed first when you select the Viewer.
This icon indicates that the USB memory is inserted into the projector.
(3) Thumbnail screen
This screen will show a list of folders and image files stored in the USB memory. The
JPEG Exif files will be displayed in thumbnail screen only.
• The maximum number of image files or folders within one page is different depending
on the model.
M361X, M311X, and M271X are 5 by 4
M311W and M271W are 6 by 4
(4) Cursor
The cursor is used to select (highlight) the folder or image file by using ▲▼◀▶ but-
ton.
(5) Back icon
This icon is used to return to the upper (parent) folder.
This icon shows that the USB memory has folders.
(6) Folder icon
(7) Page up (Page down)
This icon shows further folders or image files are available in the next (previous) page.
Use the ▶ button to go to the next (previous) row. The PAGE ▽ or PAGE △ on the
remote control is used to go to the next or previous page directly.
icon
(8) Thumbnail toolbar
(9) Slide screen
This toolbar is used in the thumbnail screen. Pressing the MENU button will display
This screen is used for manual playback. The selected image will be displayed in full
screen.
(10) Slide toolbar
This toolbar is used in the slide screen. Pressing the MENU button will display this
(11) Slideshow screen
(12) Slideshow toolbar
This screen is used for auto playback. The slides will be changed automatically.
This toolbar is used in the slideshow screen. Pressing the MENU button will display
64
4. Using the Viewer
Using the toolbar
1. Press the MENU button.
The toolbar will be displayed.
The SOURCE screen will be displayed as Viewer connection screen.
2. Use the ◀ or ▶ button to select an item and use the ▲ or ▼ button to select its available option.
When the cursor is placed, the selected item will be changed to yellow.
The ▲ or ▼ shows more available choices.
3. Press the ENTER button.
The selected item will be displayed.
4. Press the MENU button two times.
The toolbar will be closed and the SOURCE list will be displayed. Press the MENU button again to close the
SOURCE list.
Thumbnail toolbar
(1)
(2)
(3)
(4)
Menu
Options
Description
(1) Back
—
Goes back to the previous image. When the cursor reaches the top left of
the screen, it will go to the previous page.
(2) Forward
(3) Display
—
Goes to the next image. When the cursor reaches the bottom right of the
screen, it will go to the next page.
Closes the menu and returns to the thumbnail screen.
Closes the menu and starts the slideshow from the highlighted item.
Closes the menu and displays the slide screen.
(4) Order
Displays the icons alphabetically by name. (number before alphabet)
Displays the icons in descending order of file size.
Displays the icons in the order of creation date
65
4. Using the Viewer
Slide toolbar
(1)
(2)
(3)
(4)
Menu
Options
Description
Closes the menu and switches to the slide screen.
(1) Display
Closes the menu and displays the thumbnail screen.
Closes the menu and starts the slideshow from the highlighted item.
Closes the menu and displays the image in its actual size.
(2) Image
display
Closes the menu and displays the image in the projector’s maximum reso-
lution.
(3) Clockwise
—
—
Close the menu and rotate the image 90°clockwise
rotation
(4) Counter-
clockwise
rotation
Close the menu and rotate the image 90°counter clockwise
Slideshow toolbar
(1)
(2)
(3)
(4)
(5)
Menu
Options
Description
(1) Stop
—
Closes the menu and changes to the slide screen.
Goes back to the previous image.
(2) Back
—
—
(3) Forward
(4) Interval
(5) Repeat
Goes to the next image.
Specifies interval time when playing back the slides.
Repeats to play back the images in the folder.
Returns to the thumbnail screen.
TIP:
• A picture icon at the center of the screen shows that the file cannot be displayed in the slide screen or thumbnail screen.
• Slide toolbar setting for rotation will be cancelled if the folder is moved from one place to another.
66
4. Using the Viewer
Converting PowerPoint files to Slides (Viewer PPT Converter
3.0)
Using Viewer PPT Converter 3.0 contained on the supplied NEC Projector CD-ROM allows you to convert Power-
Point files into JPEG files. Converted JPEG files can be saved to a USB memory. When the USB memory inserted
into the projector, these JPEG files can be displayed with the viewer function of the projector without connecting a
computer.
NOTE:
By using PPT Converter 3.0, PowerPoint file is converted into index file (with extension “.idx”)
When conversion is done, index file (with extension “.idx”) will be created. At the same time a folder with the same name will be
created where JPEG files will be saved to. The projector’s Viewer does not support index file (with extension .idx).
Install Viewer PPT Converter 3.0 on the computer.
NOTE:
• To install or uninstall the program, the Windows user account must have “Administrator” privilege (Windows 7, Windows Vista
and Windows XP).
• Exit all running programs before installation. If another program is running, the installation may not be completed.
1. Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive.
The menu window will be displayed.
TIP:
If the menu window will not be displayed, try the following procedure.
For Windows 7:
1. Click “start” on Windows.
2. Click “All Programs” → “Accessories” → “Run”.
3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\
LAUNCHER.EXE)
4 Click “OK”.
The menu window will be displayed.
67
4. Using the Viewer
2. Click “Install Viewer PPT Converter 3.0” on the menu window.
The installation will start.
When the installation is complete, the Welcome window will be displayed.
3 Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
Read “END USER LICENSE AGREEMENT” carefully
4. If you agree, click “I accept the terms in the license agreement” and then click “Next”.
•
•
Follow the instructions on the installer screens to complete the installation.
When the installation is complete, you will return to the menu window.
NOTE:
When Viewer PPT Converter 3.0 has been installed, once start Viewer PPT Converter 3.0 once with the privilege used for installation.
Then exit from Viewer PPT Converter 3.0 without doing anything.
• Starting
Click Window’s [Start] → [All Programs] → [NEC Projector User Supportware] → [Viewer PPT Converter 3.0] → [Viewer PPT
Converter 3.0], in that order.
NOTE:
When installing Viewer PPT Converter 3.0 onto a personal computer that has PowerPoint installed, Viewer PPT Converter 3.0 is
automatically registered as a Power-Point add-in.
It is necessary to cancel Viewer PPT Converter 3.0 add-in before uninstalling Viewer PPT Converter 3.0.
Refer to Viewer PPT Converter 3.0 Help to unregister the add-in.
TIP:
• Uninstalling Viewer PPT Converter 3.0
To uninstall Viewer PPT Converter 3.0, do the same procedures stated as in “Uninstalling Virtual Remote Tool”. Read “Virtual Remote
68
4. Using the Viewer
Converting PowerPoint files and saving them to a USB memory
1. Insert the USB memory into the USB port of the computer.
2. OnWindows, click“Start”→“All programs”→“NEC Projector UserSupportware”→“Viewer PPT Converter
3.0” → “Viewer PPT Converter 3.0”.
Viewer PPT Converter 3.0 will start.
3. Click “Brows...” and select a PowerPoint file you wish to convert, and then click “Open”.
4. Click “Next”.
5. Select the USB memory drive for “Card Drive” and type in “Index name”.
Index name must be eight alphanumeric characters or less. 2-byte character and file with a long filename cannot
be used.
6. Click “Export”.
A confirmation message will be displayed.
7. Click “OK”.
Exporting a file will start.
8. Click “OK”.
9. Click “Exit”.
Viewer PPT Converter 3.0 will exit.
10. Remove the USB memory from the computer.
NOTE:
• Before removing the USB memory from the USB port of the computer, click the “Safe to Remove Hardware” icon on the task-
bar.
69
5. Using On-Screen Menu
1 Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or the projector cabinet to display the menu.
NOTE: The commands such as ENTER, EXIT, , in the bottom show available buttons for your operation.
2. Press the buttons on the remote control or the projector cabinet to display the submenu.
3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first
tab.
4. Use the buttons on the remote control or the projector cabinet to select the item you want to adjust or
set.
You can use the buttons on the remote control or the projector cabinet to select the tab you want.
5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.
6. Adjust the level or turn the selected item on or off by using the buttons on the remote control or
the projector cabinet.
Changes are stored until adjusted again.
7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the projec-
tor cabinet to quit the menu display.
NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.
8. Press the MENU button to close the menu.
To return to the previous menu, press the EXIT button.
70
5. Using On-Screen Menu
Menu Elements
Tab
Slide bar
Solid triangle
Available buttons
Source
Highlight
Radio button
Wireless symbol
ECO mode symbol
High Altitude symbol
Off Timer remaining
time
Thermometer symbol
Key Lock symbol
Menu windows or dialog boxes typically have the following elements:
Highlight�����������������������������Indicates the selected menu or item�
Solid triangle ����������������������Indicates further choices are available� A highlighted triangle indicates the item is active�
Tab��������������������������������������Indicates a group of features in a dialog box� Selecting on any tab brings its page to the front�
Radio button�����������������������Use this round button to select an option in a dialog box�
Source ��������������������������������Indicates the currently selected source�
Off Timer remaining time����Indicates the remaining countdown time when the [OFF TIMER] is preset�
Slide bar �����������������������������Indicates settings or the direction of adjustment�
ECO mode symbol��������������Indicates ECO MODE is set�
Key Lock symbol ����������������Indicates the [CONTROL PANEL LOCK] is enabled�
Thermometer symbol ���������Indicates the [ECO MODE] is forcibly set to [ON] mode because the internal temperature is too
high�
High Altitude symbol ����������Indicates the [FAN MODE] is set to [HIGH ALTITUDE] mode�
Wireless symbol �����������������Indicate the wireless LAN connection is enabled�
71
5. Using On-Screen Menu
List of Menu Items
Some menu items are not available depending on the input source.
Menu Item
Default
Options
COMPUTER1
COMPUTER2
HDMI
*
*
*
*
*
*
*
VIDEO
SOURCE
S-VIDEO
VIEWER
NETWORK
USB DISPLAY
*
*
PRESET
1–7
GENERAL
HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE, GRAPHIC,
sRGB, DICOM SIM.
REFERENCE
*
GAMMA
DYNAMIC, NATURAL, BLACK DETAIL
LARGE, MEDIUM, SMALL
CORRECTION*1
SCREEN SIZE*2
COLOR
*
*
5000, 6500, 7800, 8500, 9300, 10500
TEMPERATURE
DYNAMIC
*
*
*
OFF, ON
CONTRAST
IMAGE MODE
COLOR
DETAIL
SETTINGS
STILL, MOVIE
OFF, ON
ENHANCEMENT
WHITE BALANCE
CONTRAST R
PICTURE
0
0
0
CONTRAST G
CONTRAST B
3
BRIGHTNESS R
BRIGHTNESS G
BRIGHTNESS B
*
3
*
ADJUST
3
*
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
63
63
7
31
31
HUE
RESET
CLOCK
*
*
*
*
*
PHASE
HORIZONTAL
VERTICAL
OVERSCAN
IMAGE
0[%], 5[%], 10[%]
OPTIONS
M361X/M311X/M271X: AUTO, 4:3, 16:9, 15:9, 16:10, WIDE
ZOOM, NATIVE
M311W/M271W: AUTO, 4:3, 16:9, 15:9, 16:10, LETTERBOX,
NATIVE
*
*
ASPECT RATIO
POSITION (Not available on M311W/
M271W)
AUTO KEYSTONE
0
−96 to 96
OFF, ON
ON
0
KEYSTONE
KEYSTONE SAVE
OFF
OFF, ON
OFF, WHITEBOARD, BLACKBOARD, BLACKBOARD
(GRAY), LIGHT YELLOW, LIGHT GREEN, LIGHT BLUE,
SKY BLUE, LIGHT ROSE, PINK
WALL COLOR
OFF
ECO MODE
AUTO ECO
OFF
OFF, AUTO ECO, NORMAL, ECO
OFF, CAPTION1, CAPTION2, CAPTION3, CAPTION4,
TEXT1, TEXT2, TEXT3, TEXT4
OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00
ENGLISH, DEUTSCH, FRANÇAIS, ITALIANO, ESPAÑOL,
SVENSKA, 日本語
CLOSED CAPTION
OFF TIMER
SETUP
GENERAL
OFF
DANSK, PORTUGUÊS, ČEŠTINA, MAGYAR, POLSKI,
NEDERLANDS, SUOMI
LANGUAGE
ENGLISH
NORSK, TÜRKÇE, РУССКИЙ,
ROMÂNĂ, HRVATSKI, БЪЛГАРСКИ, INDONESIA, हिन्दी,
ไทย, , 繁體中文
, Ελληνικά, 中文, 한국어
*
The asterisk (*) indicates that the default setting varies depending on the signal.
*1 The [GAMMA CORRECTION] item is available when an item other than [DICOM SIM.] is selected for [REFERENCE].
*2 The [SCREEN SIZE] item is available when [DICOM SIM.] is selected for [REFERENCE].
*3 The default setting varies depending on the setting of [REFERENCE].
72
5. Using On-Screen Menu
Menu Item
Default
COLOR
ON
ON
OFF
Options
COLOR SELECT
SOURCE DISPLAY
ID DISPLAY
ECO MESSAGE
DISPLAY TIME
BACKGROUND
COLOR, MONOCHROME
OFF, ON
OFF, ON
OFF, ON
AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC
BLUE BLUE, BLACK, LOGO
MENU
M311X/M271X/ M311X/M271X/M271W: OFF, 100[H], 500[H], 1000[H],
M271W: 6000[H] 2000[H], 6000[H]
M361X/M311W: M361X/M311W: OFF, 100[H], 500[H], 1000[H], 2000[H],
FILTER MESSAGE
5000[H]
DESKTOP
FRONT
OFF
5000[H]
DESKTOP FRONT, CEILING REAR, DESKTOP REAR,
CEILING FRONT
OFF, ON
OFF, ON
ORIENTATION
CONTROL PANEL LOCK
SECURITY
OFF
COMMUNICATION SPEED
38400bps
4800bps, 9600bps, 19200bps, 38400bps
INSTALLATION
CONTROL ID
1
1–254
NUMBER
CONTROL ID
CONTROL ID
OFF
OFF, ON
TEST PATTERN
AUTO ADJUST
FAN MODE
NORMAL
AUTO
OFF, NORMAL, FINE
AUTO, HIGH, HIGH ALTITUDE
RGB/
COMPONENT
RGB/
COMPONENT
COMPUTER1
COMPUTER2
VIDEO
RGB/COMPONENT, RGB, COMPONENT
RGB/COMPONENT, RGB, COMPONENT
SIGNAL SELECT
WXGA MODE
SETUP
AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60,
SECAM
AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60,
SECAM
AUTO
AUTO
OPTIONS(1)
S-VIDEO
M361X/M311X/
M271X: OFF
M311W/M271W:
ON
OFF, ON
DEINTERLACE
ON
OFF, ON
VIDEO LEVEL
AUDIO SELECT
AUTO
HDMI
AUTO, NORMAL, ENHANCED
HDMI, COMPUTER2
HDMI SETTINGS
BEEP
ON
OFF, ON
STANDBY MODE
NORMAL
OFF
OFF
NORMAL, POWER-SAVING
OFF, ON
OFF, ON
OFF, 0:05, 0:10, 0:20, 0:30, 1:00
LAST, AUTO, COMPUTER1, COMPUTER2, HDMI, VIDEO,
S-VIDEO, VIEWER, NETWORK, USB DISPLAY
DISABLE, ENABLE
DIRECT POWER ON
AUTO POWER ON(COMP1)
AUTO POWER OFF
OPTIONS(2)
OFF
DEFAULT SOURCE SELECT
WIRED LAN
LAST
ENABLE
DHCP: ON
AUTO DNS: ON AUTO DNS, DNS
DHCP, IPADDRESS, SUBNET MASK, GATEWAY,
SETTINGS
WIRED LAN
RECONNECT
PROFILE
EASY
CONNECTION
DISABLE, EASY CONNECTION, PROFILE1, PROFILE2
WIRELESS LAN
RECONNECT
LAMP LIFE REMAINING
LAMP HOURS USED
FILTER HOURS USED
TOTAL CARBON SAVINGS
SOURCE NAME
SOURCE INDEX
HORIZONTAL FREQUENCY
VERTICAL FREQUENCY
SIGNAL TYPE
USAGE TIME
INFO.
SOURCE
VIDEO TYPE
SYNC TYPE
SYNC POLARITY
SCAN TYPE
IP ADDRESS
SUBNET MASK
WIRED LAN
GATEWAY
MAC ADDRESS
*
The asterisk (*) indicates that the default setting varies depending on the signal.
73
5. Using On-Screen Menu
Menu Item
Default
Options
IP ADDRESS
SUBNET MASK
GATEWAY
MAC ADDRESS
WIRELESS LAN SSID
NETWORK TYPE
WEP/WPA
CHANNEL
INFO.
SIGNAL LEVEL
FIRMWARE
VERSION
OTHERS
DATA
PROJECTOR NAME
MODEL NO.
SERIAL NUMBER
LAN UNIT TYPE
CONTROL ID (when [CONTROL ID]
is set)
CURRENT SIGNAL
ALL DATA
RESET
CLEAR LAMP HOURS
CLEAR FILTER HOURS
*
The asterisk (*) indicates that the default setting varies depending on the signal.
74
5. Using On-Screen Menu
Menu Descriptions & Functions [SOURCE]
COMPUTER 1 and 2
Selects the computer connected to your COMPUTER 1 or COMPUTER 2 input connector signal.
NOTE: When the component input signal is connected to the COMPUTER 1 IN or COMPUTER 2 IN connector, select [COMPUTER
1] or [COMPUTER 2] respectively.
HDMI
Selects the HDMI compatible equipment connected to your HDMI IN connector.
VIDEO
Selects what is connected to your VIDEO input-VCR, DVD player or document camera.
S-VIDEO
Selects what is connected to your S-VIDEO input-VCR or DVD player.
NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or S-
Video source.
VIEWER
This feature enables you to make presentations using a USB memory that contains slides.
NETWORK
Selects a signal from the LAN port (RJ-45) or the installed USB wireless LAN unit (optional).
USB DISPLAY
Selects the computer connected to the USB(PC) port (type B) by using a commercially available USB cable.
75
5. Using On-Screen Menu
Menu Descriptions & Functions [ADJUST]
[PICTURE]
[PRESET]
This function allows you to select optimized settings for your projected image.
You can adjust neutral tint for yellow, cyan or magenta.
There are seven factory presets optimized for various types of images.You can also use [DETAIL SETTINGS] to set
user adjustable settings to customize each gamma or color.
Your settings can be stored in [PRESET 1] to [PRESET 7].
HIGH-BRIGHT�������� Recommended for use in a brightly lit room�
PRESENTATION����� Recommended for making a presentation using a PowerPoint file�
VIDEO�������������������� Recommended for typical TV program viewing�
MOVIE ������������������� Recommended for movies�
GRAPHIC��������������� Recommended for graphics�
sRGB ��������������������� Standard color values
DICOM SIM� ���������� Recommended for DICOM simulation format�
NOTE:
• The [DICOM SIM.] option is for training/reference only and should not be used for actual diagnosis.
• DICOM stands for Digital Imaging and Communications in Medicine. It is a standard developed by the American College of Radiol-
ogy (ACR) and the National Electrical Manufacturers Association (NEMA).
The standard specifies how digital image data can be moved from system to system.
[DETAIL SETTINGS]
76
5. Using On-Screen Menu
[GENERAL]
Storing Your Customized Settings [REFERENCE]
This function allows you to store your customized settings in [PRESET 1] to [PRESET 7].
First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERA-
TURE].
HIGH-BRIGHT�������� Recommended for use in a brightly lit room�
PRESENTATION����� Recommended for making a presentation using a PowerPoint file�
VIDEO�������������������� Recommended for typical TV program viewing�
MOVIE ������������������� Recommended for movies�
GRAPHIC��������������� Recommended for graphics�
sRGB ��������������������� Standard color values�
DICOM SIM� ���������� Recommended for DICOM simulation format�
Selecting Gamma Correction Mode [GAMMA CORRECTION]
Each mode is recommended for:
DYNAMIC �������������� Creates a high-contrast picture�
NATURAL��������������� Natural reproduction of the picture�
BLACK DETAIL������� Emphasizes detail in dark areas of the picture�
NOTE: This function is not available when [DICOM SIM.] is selected for [DETAIL SETTINGS].
Selecting Screen Size for DICOM SIM [SCREEN SIZE]
This function will perform gamma correction appropriate for the screen size.
LARGE������������������� For screen size of 150"
MEDIUM���������������� For screen size of 100"
SMALL������������������� For screen size of 50"
NOTE: This function is available only when [DICOM SIM.] is selected for [DETAIL SETTINGS].
Adjusting Color Temperature [COLOR TEMPERATURE]
This option allows you to select the color temperature of your choice.
NOTE: When [PRESENTATION] or [HIGH-BRIGHT] is selected in [REFERENCE], this function is not available.
Adjusting Brightness and Contrast [DYNAMIC CONTRAST]
This function allows you to adjust the contrast ratio optically using the built-in iris.
To increase the contrast ratio, select [ON].
Selecting Still Image Mode or Movie Mode [IMAGE MODE]
This function allows you to select the still image mode or the movie mode.
STILL��������������������� This mode is for a still image�
MOVIE ������������������� This mode is for a movie�
NOTE: This function is available only when [HIGH-BRIGHT] is selected for [REFERENCE].
77
5. Using On-Screen Menu
Enhancing the Color [COLOR ENHANCEMENT]
This function allows you to enhance the color of image.
OFF ������������������������ Does not enhance the color
ON ������������������������� Enhances the color�
NOTE: This function is available only when [PRESENTATION] is selected [REFERENCE].
Adjusting White Balance [WHITE BALANCE]
This allows you to adjust the white balance. Contrast for each color (RGB) to adjust the white level of the screen;
Brightness for each color (RGB) is used to adjust the black level of the screen.
[CONTRAST]
Adjusts the intensity of the image according to the incoming signal.
[BRIGHTNESS]
Adjusts the brightness level or the back raster intensity.
[SHARPNESS]
Controls the detail of the image.
[COLOR]
Increases or decreases the color saturation level.
[HUE]
Varies the color level from +/− green to +/− blue. The red level is used as reference.
Input signal
CONTRAST
BRIGHTNESS SHARPNESS
COLOR
No
HUE
No
COMPUTER/HDMI (RGB)
COMPUTER/HDMI (COMPONENT)
VIDEO/S-VIDEO/COMPONENT
VIEWER/NETWORK/USB DISPLAY
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes = Adjustable, No = Not adjustable
[RESET]
The settings and adjustments for [PICTURE] will be returned to the factory settings with the exception of the following;
Preset numbers and [REFERENCE] within the [PRESET] screen.
The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently selected
will not be reset.
78
5. Using On-Screen Menu
[IMAGE OPTIONS]
Adjusting Clock and Phase [CLOCK/PHASE]
This allows you to manually adjust CLOCK and PHASE.
CLOCK������������������� Use this item to fine tune the computer image or to remove any vertical banding that might appear� This
function adjusts the clock frequencies that eliminate the horizontal banding in the image�
This adjustment may be necessary when you connect your computer for the first time�
PHASE������������������� Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk� (This is
evident when part of your image appears to be shimmering�)
Use [PHASE] only after the [CLOCK] is complete�
NOTE: The [CLOCK] and [PHASE] items are available for RGB signals only.
79
5. Using On-Screen Menu
Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL]
Adjusts the image location horizontally and vertically.
NOTE: The [HORIZONTAL] and [VERTICAL] items are not available for VIDEO, S-VIDEO, HDMI, VIEWER, NETWORK, and USB
DISPLAY.
-
-
An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction.
The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the
current signal. The next time you project the signal with the same resolution, horizontal and vertical frequency,
its adjustments will be called up and applied.
To delete adjustments stored in memory, from the menu, you select [RESET] → [CURRENT SIGNAL] or [ALL
DATA] and reset the adjustments.
Selecting Overscan Percentage [OVERSCAN]
Select overscan percentage (0%, 5% and 10%) for signal.
Projected image
Overscaned by 10%
NOTE:
• The [0[%]] cannot be selected when VIDEO and S-VIDEO signals are used.
• The [OVERSCAN] item is not available:
• when [NATIVE] is selected for [ASPECT RATIO].
• when [VIEWER], [NETWORK], or [USB DISPLAY] is selected for [SOURCE]
80
5. Using On-Screen Menu
Selecting Aspect Ratio [ASPECT RATIO]
The term “aspect ratio” refers to the ratio of width to height of a projected image.
The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio.
• This table shows typical resolutions and aspect ratios that most computers support.
Resolution
640 × 480
Aspect Ratio
4:3
VGA
SVGA
XGA
WXGA
WXGA
WXGA+
SXGA
SXGA+
UXGA
WUXGA
800 × 600
1024 × 768
1280 × 768
1280 × 800
1440 × 900
1280 × 1024
1400 × 1050
1600 × 1200
1920 × 1200
4:3
4:3
15:9
16:10
16:10
5:4
4:3
4:3
16:10
Options
Function
AUTO
The projector will automatically determine the incoming signal and display it in its aspect
The projector may erroneously determine the aspect ratio depending on its signal. If this
occurs, select the appropriate aspect ratio from the following.
4:3
The image is displayed in 4:3 aspect ratio.
The image is displayed in 16:9 aspect ratio.
The image is displayed in 15:9 aspect ratio.
The image is displayed in 16:10 aspect ratio.
The image is stretched left and right.
16:9
15:9
16:10
WIDE ZOOM
(M361X/M311X/M271X) Parts of the displayed image are cropped at the left and right edges and therefore not
visible.
LETTERBOX
(M311W/M271W)
The image of a letterbox signal is stretched equally in the horizontal and vertical direc-
tions to fit the screen. Parts of the displayed image are cropped at the top and bottom
edges and therefore not visible.
NATIVE
The projector displays the current image in its true resolution when the incoming computer
signal has a lower resolution than the projector’s native resolution.
[Example 1] When the incoming
signal with the resolution of 800
× 600 is displayed on the M361X/
M311X/M271X:
[Example 2] When the incoming
signal with the resolution of 800 ×
600 is displayed on the M311W/
M271W:
NOTE:
• When a non-computer signal is displayed, the [NATIVE] is not available.
• When a signal with a higher resolution than the projector’s native resolution is displayed, [NA-
TIVE] is not available.
81
5. Using On-Screen Menu
Sample image when the appropriate aspect ratio is automatically determined
M361X/M311X/M271X
[Computer signal]
Aspect ratio of incoming signal
4:3
5:4
16:9
15:9
16:10
Sample image when the appro-
priate aspect ratio is automati-
cally determined
[Video signal]
Aspect ratio of incoming signal
4:3
Letterbox
Squeeze
Sample image when the as-
pect ratio is automatically de-
termined
NOTE: To display a squeezed signal prop-
erly, select [16:9] or [WIDE ZOOM].
M311W/M271W
[Computer signal]
Aspect ratio of incoming signal
4:3
4:3
5:4
16:9
15:9
16:10
Sample image when the appro-
priate aspect ratio is automati-
cally determined
[Video signal]
Aspect ratio of incoming signal
Letterbox
Squeeze
Sample image when the as-
pect ratio is automatically de-
termined
NOTE: To display a letterbox signal prop- NOTE: To display a squeezed signal prop-
erly, select [LETTERBOX]. erly, select [16:9].
TIP:
• Image position can be adjusted vertically using [POSITION] when the [16:9], [15:9], or [16:10] aspect ratios are selected.
• The term “letterbox” refers to a more landscape-oriented image when compared to a 4:3 image, which is the standard aspect
ratio for a video source.
The letterbox signal has aspect ratios with the vista size “1.85:1” or cinema scope size “2.35:1” for movie film.
• The term “squeeze” refers to the compressed image of which aspect ratio is converted from 16:9 to 4:3.
Adjusting the Vertical Position of Image [POSITION] (not available on M311W/M271W)
(only when [16:9], [15:9], or [16:10] is selected for [ASPECT RATIO])
When [16:9], [15:9], or [16:10] is selected in [ASPECT RATIO], the image is displayed with black borders on the top
and bottom.
You can adjust the vertical position from the top to the bottom of the black area.
82
5. Using On-Screen Menu
Menu Descriptions & Functions [SETUP]
[GENERAL]
Enabling Auto Keystone [AUTO KEYSTONE]
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
To turn on the AUTO KEYSTONE feature, select [ON]. To adjust the KEYSTONE feature manually, select [OFF].
NOTE: The [AUTO KEYSTONE] function is not available when an orientation type such as [CEILING REAR], [DESKTOP REAR],
[CEILING FRONT] other than [DESKTOP/FRONT] is selected for [ORIENTATION].
Correcting Vertical Keystone Distortion Manually [KEYSTONE]
TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.
Saving Vertical Keystone Correction [KEYSTONE SAVE]
This option enables you to save your current keystone settings.
OFF ������������������������ Does not save current keystone correction settings� It will return your keystone correction settings to
“zero”�
ON ������������������������� Saves current keystone correction settings
Saving your change once affects all sources. The changes are saved when the projector is turned off.
NOTE: When [AUTO KEYSTONE] is set to [ON], [KEYSTONE SAVE] is not available. Next time you turn on the power, the AUTO
KEYSTONE function will work and the data stored with [KEYSTONE SAVE] will be invalid.
83
5. Using On-Screen Menu
Using the Wall Color Correction [WALL COLOR]
This function allows for quick adaptive color correction in applications where the screen material is not white.
NOTE: Selecting [WHITEBOARD] reduces lamp brightness.
Setting Eco Mode [ECO MODE]
The ECO MODE increases lamp life, while lowering power consumption and cutting down on CO2 emissions.
Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL] and [ECO] modes.
84
5. Using On-Screen Menu
Setting Closed Caption [CLOSED CAPTION]
This option sets several closed caption modes that allow text to be superimposed on the projected image of Video
or S-Video.
OFF ������������������������ This exits the closed caption mode�
CAPTION 1-4 ��������� Text is superimposed�
TEXT 1-4���������������� Text is displayed�
NOTE:
• The closed caption is not available under the following conditions:
- when messages or menus are displayed.
- when an image is magnified, frozen, or muted.
• Portions of superimposed text or closed caption may be truncated. If that happens, try to place the superimposed text or
closed caption within the screen.
Using Off Timer [OFF TIMER]
1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
• To cancel the preset time, set [OFF] for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off, the [THE PROJECTOR WILL TURN OFF WITHIN 3
MINUTES] message will be displayed on the bottom of the screen.
Selecting Menu Language [LANGUAGE]
You can choose one of 29 languages for on-screen instructions.
NOTE: Your setting will not be affected even when [RESET] is done from the menu.
[MENU]
Selecting Menu Color [COLOR SELECT]
You can choose between two options for menu color: COLOR and MONOCHROME.
Turning On / Off Source Display [SOURCE DISPLAY]
This option turns on or off input name display such as COMPUTER 1, COMPUTER2, HDMI, VIDEO, S-VIDEO,
VIEWER, NETWORK, USB DISPLAY, to be displayed on the top right of the screen.
When no input signal is present, the no-signal guidance prompting you to check for an available input will be displayed
at the center of the screen. When the [VIEWER] or [NETWORK] item is selected for [SOURCE], the no-signal guid-
ance will not be displayed.
85
5. Using On-Screen Menu
Turning ON/OFF Control ID [ID DISPLAY]
ID DISPLAY ����������� This option turns on or off the ID number which is displayed when the ID SET button on the remote control
is pressed�
Turning On / Off Eco Message [ECO MESSAGE]
This option turns on or off the following messages when the projector is turned on.
The Eco Message prompts the user to save energy. When [OFF] is selected for [ECO MODE], you will get a message
to prompt you to select [AUTO ECO], [NORMAL], or [ECO] for [ECO MODE].
When [AUTO ECO], [NORMAL], or [ECO] is selected for [ECO MODE]
To close the message, press any one of the buttons. The message will disappear if no button operation is done for
30 seconds.
When [OFF] is selected for [ECO MODE]
To close the message, press the EXIT button.
Selecting Menu Display Time [DISPLAY TIME]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The
preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the fac-
tory preset.
Selecting a Color or Logo for Background [BACKGROUND]
Use this feature to display a blue/black screen or logo when no signal is available. The default background is
[BLUE].
NOTE:
• If the [LOGO] item is selected for [BACKGROUND] with the [NETWORK] or [USB DISPLAY] source selected, the [BLUE] item will
be selected regardless of its selection.
• When [SOURCE DISPLAY] is turned on, the no-signal guidance prompting you to check for an available input will be displayed
at the center of the screen regardless of its selection.
• Your setting will not be affected even when [RESET] is done from the menu.
Selecting Interval Time for Filter Message [FILTER MESSAGE]
This option allows you to select the time preference between displaying the message for cleaning the filters. Clean
Six options are available:
M311X/M271X/M271W: OFF, 100[H], 500[H], 1000[H], 2000[H], 6000[H]
M361X/M311W: OFF, 100[H], 500[H], 1000[H], 2000[H], 5000[H]
NOTE: Your setting will not be affected even when [RESET] is done from the menu.
86
5. Using On-Screen Menu
[INSTALLATION]
Selecting Projector Orientation [ORIENTATION]
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
DESKTOP FRONT
CEILING REAR
DESKTOP REAR
CEILING FRONT
Disabling the Cabinet Buttons [CONTROL PANEL LOCK]
This option turns on or off the CONTROL PANEL LOCK function.
NOTE:
• This CONTROL PANEL LOCK does not affect the remote control functions.
• When the control panel is locked, pressing and holding the EXIT button on the projector cabinet for about 10 seconds will change
the setting to [OFF].
TIP: When the [CONTROL PANEL LOCK] is turned on, a key lock icon [
] will be displayed at the bottom right of the menu.
Enabling Security [SECURITY]
This feature turns on or off the SECURITY function.
NOTE: Your setting will not be affected even when [RESET] is done from the menu.
87
5. Using On-Screen Menu
Selecting Communication Speed [COMMUNICATION SPEED]
This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps.The
default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equip-
ment, a lower baud rate may be recommended for long cable runs).
NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.
Setting ID to the Projector [CONTROL ID]
You can operate multiple projectors separately and independently with the single remote control that has the CONTROL
ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together
using the single remote control. To do so, you have to assign an ID number to each projector.
CONTROL ID NUMBER�������Select a number from 1 to 254 you wish to assign to your projector�
CONTROL ID�����������������������Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set-
ting�
NOTE:
• When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support
the CONTROL ID function. (In this case the buttons on the projector cabinet can be used.)
• Your setting will not be affected even when [RESET] is done from the menu.
• Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Control
ID.
Assigning or Changing the Control ID
1. Turn on the projector.
2. Press the ID SET button on the remote control.
The CONTROL ID screen will be displayed.
If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed. If the projector
cannot be operated with the current remote control ID, the [INACTIVE] will be displayed. To operate the inactive
projector, assign the control ID used for the projector by using the following procedure (Step 3).
3. Press one of numeric keypad buttons while pressing and holding the ID SET
button on the remote control.
Example:
To assign “3”, press the “3” button on the remote control.
No ID means that all the projectors can be operated together with a single remote
control. To set “No ID”, enter “000” or press the CLEAR button.
TIP: The range of IDs is from 1 to 254.
4. Release the ID SET button.
The updated CONTROL ID screen will be displayed.
NOTE:
• The IDs can be cleared in a few days after the batteries are run down or removed.
• Accidentally pressing any one of the buttons of the remote control will clear currently specified
ID with batteries removed.
88
5. Using On-Screen Menu
Using Test Pattern [TEST PATTERN]
Displays the test pattern to check for image distortion at the time of the projector setup. Press the ENTER button to
display the test pattern; press the EXIT button to close the test pattern and return to the menu. Menu operation and
keystone correction are not possible when the test pattern is displayed.
[OPTIONS(1)]
Setting Auto Adjust [AUTO ADJUST]
This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for
noise and stability.You can automatically make adjustment in two ways: [NORMAL] and [FINE].
OFF ������������������������ The computer signal will not be automatically adjusted� You can manually optimize the computer signal�
NORMAL���������������� Default setting� The computer signal will be automatically adjusted� Normally select this option�
FINE����������������������� Select this option if fine adjustment is needed� It takes more time to switch to the source than when [NOR-
MAL]is selected�
Selecting Fan Mode [FAN MODE]
This option allows you to select three modes for fan speed: Auto mode, High speed mode, and High Altitude mode.
AUTO��������������������� The built-in fans automatically run at a variable speed according to the internal temperature�
HIGH���������������������� The built-in fans run at high speed�
HIGH ALTITUDE����� The built-in fans run at a high speed� Select this option when using the projector at altitudes approximately
5500 feet/1600 meters or higher�
When you wish to cool down the temperature inside the projector quickly, select [HIGH].
NOTE:
• It is recommended that you select High speed mode if you use the projector non-stop for consecutive days.
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters or higher.
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause
the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and turn on the projector.
• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the
lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical components such
as the lamp.
• Your setting will not be affected even when [RESET] is done from the menu.
89
5. Using On-Screen Menu
Selecting Signal Format [SIGNAL SELECT]
[COMPUTER1], [COMPUTER2]
Allows you to choose [COMPUTER1], or [COMPUTER2] for an RGB source such as a computer, or [COMPONENT]
for a component video source such as a DVD player. Normally select [RGB/COMPONENT] and the projector auto-
matically detects a component signal. However there may be some component signals that the projector is unable to
detect. If this is the case, select [COMPONENT].
[VIDEO & S-VIDEO System Select]
This feature enables you to select composite video standards automatically or manually.
Normally select [AUTO] and the projector will automatically detect the video standard.
In the case where the projector has difficulty detecting the video standard, select the appropriate video standard from
the menu.
This must be done for VIDEO and S-VIDEO respectively.
Enabling or Disabling WXGA Mode [WXGA MODE]
Selecting [ON] will give priority to WXGA (1280 × 768)/WUXGA (1920 × 1080) signals in recognizing an input sig-
nal.
When [WXGA MODE] is set to [ON], XGA (1024 × 768)/UXGA (1600 × 1200) signals may not be recognized on
M361X/M311X/M271X. In this case, select [OFF].
NOTE:
• The [OFF] is selected at the time of shipment of M361X/M311X/M271X.
• The [ON] is selected at the time of shipment of M311W/M271W.
Enabling the deinterlace [DEINTERLACE]
Turns on or off the deinterlace function for a telecine signal.
OFF ������������������������ Select this option if there is any jitter or artifacts in video�
ON ������������������������� Default standard setting�
NOTE: This feature is not available for HDTV (progressive) and computer signals.
Setting HDMI [HDMI SETTINGS]
Make the settings for video level and audio level when connecting HDMI equipment such as a DVD player.
VIDEO LEVEL��������� Select [AUTO] to automatically detect video level� If automatic detection may not work well, select [NOR-
MAL] to disable the [ENHANCED] feature of your HDMI equipment or select [ENHANCED] to improve image
contrast and increase detail in the dark areas�
AUDIO SELECT������ Select [HDMI] to switch the HDMI IN digital audio signal and select [COMPUTER 2] to switch the COMPUTER
2 input audio signal�
Enabling Key Sound and Error Sound [BEEP]
This feature turns on or off the button sound or alarm when an error occurs or the following operations are per-
formed.
- Displaying the main menu
- Switching sources
- Resetting data by using [RESET]
- Pressing POWER ON or POWER OFF button
90
5. Using On-Screen Menu
[OPTIONS(2)]
Selecting Power-saving in [STANDBY MODE]
The projector has two standby modes: [NORMAL] and [POWER-SAVING].
The POWER-SAVING mode is the mode that allows you to put the projector in the power-saving condition which
consumes less power than the NORMAL mode. The projector is preset for NORMAL mode at the factory.
NORMAL���������������� Power indicator: Orange light/STATUS indicator: Green light
POWER-SAVING���� Power indicator: Red light/STATUS indicator: Off
The following connectors, buttons or functions will not work during this mode�
- MONITOR OUT (COMP� 1) connector, and AUDIO OUT connector
- LAN and Mail Alert functions
- Buttons other than POWER button on the cabinet
- Buttons other than POWER ON button on the remote control
- Virtual Remote Tool, USB Display fucntion
NOTE:
• When [CONTROL PANEL LOCK], [CONTROL ID], or [AUTO POWER ON(COMP1)] is turned on, the [STANDBY MODE] setting is
not available.
• Even when [POWER-SAVING] is selected for [STANDBY MODE], power on or off can be done by using the PC CONTROL port.
• The power consumption in the standby mode will not be included in calculating CO2 emission reduction.
• Your setting will not be affected even when [RESET] is done from the menu.
Enabling Direct Power On [DIRECT POWER ON]
Turns the projector on automatically when the power cord is inserted into an active power outlet. This eliminates the
need to always use the POWER button on the remote control or projector cabinet.
91
5. Using On-Screen Menu
Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP1)]
When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER1
IN input will power on the projector and simultaneously project the computer’s image.
This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet
to power on the projector.
To use this function, first connect a computer to the projector and the projector to an active AC input.
NOTE:
• Disconnecting a computer signal from the computer will not power off the projector. We recommend using this function in com-
bination of the AUTO POWER OFF function.
• This function will not be available under the following conditions:
- when a component signal is applied to the COMPUTER1 IN connector
- when a Sync on Green RGB signal or composite sync signal is applied
• To enable the AUTO POWER ON (COMP1) after turning off the projector, wait 3 seconds and input a computer signal.
If a computer signal is still present when the projector is turned off, the AUTO POWER ON (COMP1) will not work and the projector
remains in standby mode.
Enabling Power Management [AUTO POWER OFF]
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5min., 10min.,
20min., 30min., 60min.) if there is no signal received by any input or if no operation is performed.
Selecting Default Source [DEFAULT SOURCE SELECT]
You can set the projector to default to any one of its inputs each time the projector is turned on.
LAST���������������������� Sets the projector to default to the previous or last active input each time the projector is turned on�
AUTO��������������������� Searches for an active source in order of COMPUTER1 → COMPUTER2 → HDMI → VIDEO → S-VIDEO →
VIEWER → USB DISPLAY → COMPUTER1 and displays the first found source�
COMPUTER1 ��������� Displays the computer signal from the COMPUTER 1 IN connector every time the projector is turned on�
COMPUTER2 ��������� Displays the computer signal from the COMPUTER 2 IN connector every time the projector is turned on�
HDMI��������������������� Displays the digital source from the HDMI IN connector every time the projector is turned on�
VIDEO�������������������� Displays the Video source from the VIDEO IN connector every time the projector is turned on�
S-VIDEO ���������������� Displays the Video source from the S-VIDEO IN connector every time the projector is turned on�
VIEWER����������������� Displays slides or plays back movie files from the USB memory device every time the projector is turned
on�
NETWORK ������������� Displays a signal from LAN port (RJ-45) or the USB Wireless LAN Unit�
USB DISPLAY�������� Displays the computer signal from the USB (PC) port every time the projector is turned on�
92
5. Using On-Screen Menu
Setting up the Projector for a Wired LAN Connection [WIRED LAN]
Important
• Consult with your network administrator about these settings.
• When using a wired LAN connection, connect a LAN cable (Ethernet cable) to the LAN port (RJ-45) of the projec-
TIP: The network settings you make will not be affected even when [RESET] is done from the menu.
[WIRED LAN]
[SETTINGS]
[DISABLE]
[ENABLE]
[DHCP]
Wired LAN connection will be turned off.
Wired LAN connection will be turned on.
ON��������������������������IP address, subnet mask, and gateway will
be automatically assigned to the projector
from your DHCP server�
OFF�������������������������Specify IP address, subnet mask, and gate-
way assigned by your network administra-
tor�
[IP ADDRESS]
[SUBNET MASK]
[GATEWAY]
Set your IP address of the network connected to the
projector.
Set your subnet mask number of the network connected
to the projector.
Set the default gateway of the network connected to the
projector.
[AUTO DNS]
ON��������������������������DHCP server will automatically assign IP
address of DNS server connected to the
projector�
OFF�������������������������Set your IP address of DNS server connected
to the projector�
93
5. Using On-Screen Menu
Setting up the Projector for a Wireless LAN Connection (with the optional USB Wireless
LAN Unit equipped) [WIRLESS LAN]
Important
• Consult with your network administrator about these settings.
• When using a wireless LAN connection, attach the optional USB Wireless LAN to the projector. (→ page 111)
[PROFILE]
[DISABLE]
Wireless LAN connection will be turned off
[EASY CONNECTION]
Select [EASY CONNECTION] to execute a wireless LAN
easily using Image Express Utility Lite on the supplied
NEC Projector CD-ROM.
[PROFILE 1]
[PROFILE 2]
Up to two settings for the USB wireless LAN unit can be
To recall the settings from memory, select [PROFILE 1] or
[PROFILE 2] from [PROFILE].
[RECONNECT]
Retry to connect the projector to a network. Try this if you have changed [PROFILE].
NOTE: After selecting [EASY CONNECTION] from [PROFILE], you cannot make settings to [DHCP], [IP ADDRESS], [SUBNET MASK],
[GATEWAY], and [AUTO DNS] except [CHANNEL].
94
5. Using On-Screen Menu
Hints on How to Set Up LAN Connection
To set up the projector for a LAN connection:
Access the HTTP server function to display the web browser (→ page 41) and select [NETWORK SETTINGS] →
[SETTINGS] → [WIRELESS LAN] → [PROFILE 1] or [PROFILE 2].
Two settings can be set for the USB Wireless LAN Unit.
Next select [SETTINGS] for your selected profile, and set [ENABLE] or [DISABLE] for [DHCP], [IP ADDRESS],
[SUBNET MASK], and [GATEWAY]. Last click [SAVE]. To reflect changes, click the [SETTING] tab and then click
To recall LAN settings stored in the profile number:
Use [PROFILE 1] or [PROFILE 2] set on the HTTP server, from the projector’ menu, select [SETUP] → [WIRELESS
LAN] → [PROFILE] → [PROFILE 1] or [PROFILE 2]. Last select [OK] and press the ENTER button. (→ page 94)
To connect a DHCP server:
From the projector menu, select [SETUP] → [WIRED LAN] → [SETTINGS] → [DHCP] → [ON] and press the ENTER
button. To specify IP address without using the DHCP server, use the HTTP server function. (→ page 41)
To set only for wireless LAN (NETWORK TYPE and WEP/WPA):
Access the HTTP server function to display the web browser (→ page 41) and select [NETWORK SETTINGS] →
[SETTINGS] → [WIRELESS LAN] → [PROFILE 1] or [PROFILE 2].
Make necessary settings for [SETTINGS] and click [SAVE].
From the projector menu, select [SETUP] → [WIRELESS LAN] → [PROFILE] → [PROFILE 1] or [PROFILE 2].
To select an SSID:
Access the HTTP server function to display the web browser (→ page 41) and select [NETWORK SETTINGS] →
[SETTINGS] → [WIRELESS LAN] → [CONNECTION] → [SITE SURVEY] and select the ID.
If you do not use [SITE SURVEY], type the SSID in [CONNECTION] and select [INFRASTRUCTURE] or [AD HOC].
To receive lamp replacement time or error messages via e-mail:
Access the HTTP server function to display the web browser (→ page 41) and select [NETWORK SETTINGS] →
[ALERT MAIL], and set [SENDER’S ADDRESS], [SMTP SERVER NAME], and [RECIPIENT’S ADDRESS]. Last,
To execute [EASY CONNECTION] using Image Express Utility Lite:
The [EASY CONNECTION] is a mode that can abbreviate the troublesome LAN settings when using the Image
Express Utility Lite and connecting the PC and projector via a wireless LAN.
The Image Express Utility Lite is contained on the supplied NEC Projector CD-ROM.
To use [EASY CONNECTION], access the HTTP server function to display the web browser (→ page 41) and select
[NETWORK SETTINGS] → [SETTINGS] → [WIRELESS LAN] → [EASY CONNECTION]. Next select [SETTINGS]
→ [CHANNEL]. Last click [SAVE].
From the projector menu, select [SETUP] → [WIRELESS LAN] → [PROFILE] → [EASY CONNECTION].
95
5. Using On-Screen Menu
Menu Descriptions & Functions [INFO.]
Displays the status of the current signal and lamp usage. This item has six pages. The information included is as
follows:
TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items.
[USAGE TIME]
[LAMP LIFE REMAINING] (%)*
[LAMP HOURS USED] (H)
[FILTER HOURS USED] (H)
[TOTAL CARBON SAVINGS] (kg-CO2)
*
The progress indicator shows the percentage of remaining bulb life.
The value informs you of the amount of lamp usage. When the remaining lamp time reaches 0, the LAMP LIFE
REMAINING bar indicator changes from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not turn on.
•
The message to the effect that the lamp or the filters should be replaced will be displayed for one minute when
the projector is turned on and when the POWER button on the projector or the remote control is pressed.
To dismiss this message, press any button on the projector or the remote control.
Lamp life(H)
ECO MODE
NORMAL
Replacement lamp
Model
OFF/AUTO ECO
ECO
4000
5000
5000
6000
8000
10000
NP16LP
NP15LP
M361X/M311W
M311X/M271X/M271W
•
[TOTAL CARBON SAVINGS]
This displays the estimated carbon saving information in kg. The carbon footprint factor in the carbon saving cal-
96
5. Using On-Screen Menu
[SOURCE]
[SOURCE NAME]
[HORIZONTAL FREQUENCY]
[SIGNAL TYPE]
[SOURCE INDEX]
[VERTICAL FREQUENCY]
[VIDEO TYPE]
[SYNC TYPE]
[SYNC POLARITY]
[SCAN TYPE]
[WIRED LAN]
[IP ADDRESS] [SUBNET MASK]
[GATEWAY]
[MAC ADDRESS]
[WIRELESS LAN]
[IP ADDRESS] [SUBNET MASK]
[GATEWAY]
[SSID]
[WEP/WPA]
[SIGNAL LEVEL]
[MAC ADDRESS]
[NETWORK TYPE]
[CHANNEL]
97
5. Using On-Screen Menu
Menu Descriptions & Functions [RESET]
Returning to Factory Default [RESET]
The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except
the following:
[CURRENT SIGNAL]
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS],
[ASPECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].
[ALL DATA]
Reset all the adjustments and settings for all the signals to the factory preset.
All items can be reset EXCEPT [LANGUAGE], [BACKGROUND], [FILTER MESSAGE], [SECURITY], [COMMUNI-
CATION SPEED], [CONTROL ID], [STANDBY MODE], [FAN MODE], [LAMP LIFE REMAINING], [LAMP HOURS
USED], [FILTER HOURS USED], [TOTAL CARBON SAVINGS], [WIRED LAN], and [WIRELESS LAN].
To reset the lamp usage time, see “Clearing Lamp Hour Meter [CLEAR LAMP HOURS]” below.
Clearing Lamp Hour Meter [CLEAR LAMP HOURS]
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press
the ENTER button.
NOTE: Elapsed time of the lamp use will not be affected even when [RESET] is done from the menu.
NOTE: The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the
lamp has reached the end of its life. In this condition you cannot clear the lamp hour meter on the menu. If this happens, press the
HELP button on the remote control for 10 seconds to reset the lamp clock back to zero. Do this only after replacing the lamp.
Clearing the Filter Usage Hours [CLEAR FILTER HOURS]
Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press
the ENTER button.
NOTE: Elapsed time of the filter use will not be affected even when [RESET] is done from the menu.
99
6. Installation and Connections
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
z
x
Set up a screen and the projector.
1
Connect your computer or video equip-
ment to the projector.
111)
c
Connect the supplied power cord.
NOTE: Ensure that the power cord and any other
cables are disconnected before moving the pro-
jector. When moving the projector or when it is
not in use, cover the lens with the sliding lens
cover.
3
2
To the wall outlet.
1 Setting Up the Screen and the Projector
Selecting a Location
[M361X/M311X/M271X]
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 25" (0.64 m) measured diagonally when the projector is roughly 35 inches (0.9 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 435 inches (11.0 m) from the wall
or screen.
Screen Size (Unit: cm/inch)
609.6(W)�457.2(H) / 240(W)�180(H)
300"
Screen Size
487.7(W)�365.8(H) / 192(W)�144(H)
240"
406.4(W)�304.8(H) / 160(W)�120(H)
200"
365.8(W)�274.3(H) / 144(W)�108(H)
180"
304.8(W)�228.6(H) / 120(W)�90(H)
150"
243.8(W)�182.9(H) / 96(W)�72(H)
120"
203.2(W)�152.4(H) / 80(W)�60(H)
100"
162.6(W)�121.9(H) / 64(W)�48(H)
80"
121.9(W)�91.4(H) / 48(W)�36(H)
60"
81.3(W)�61.0(H) / 32(W)�24(H)
40"
61.0(W)�45.7(H) / 24(W)�18(H)
30"
50.8(W)�38.1(H) / 20(W)�15(H)
"
"
25"
"
"
"
Lens center
8.8/348
"
7.3/289
11.0/435
6.6/260
"
"
"
0.9/
35
"
5.5/216
"
"
1.1/
42
4.4/173
2.2/86
3.6/144
2.9/115
1.4/57
m/inch)
:
(Unit
Distance
TIP:
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
100
6. Installation and Connections
[M311W/M271W]
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 25" (0.64 m) measured diagonally when the projector is roughly 37 inches (0.9 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 459 inches (11.7 m) from the wall
or screen.
Screen Size (Unit: cm/inch)
646.2(W)�403.9(H) / 254(W)�159(H)
300"
Screen Size
516.9(W)�323.1(H) / 204(W)�127(H)
240"
430.8(W)�269.2(H) / 170(W)�106(H)
200"
387.7(W)�242.3(H) / 153(W)�95(H)
180"
323.1(W)�201.9(H) / 127(W)�79(H)
150"
258.5(W)�161.5(H) / 102(W)�64(H)
120"
215.4(W)�134.6(H) / 85(W)�53(H)
100"
172.3(W)�107.7(H) / 68(W)�42(H)
80"
129.2(W)�80.8(H) / 51(W)�32(H)
60"
86.2(W)�53.8(H) / 34(W)�21(H)
40"
64.6(W)�40.4(H) / 25(W)�16(H)
30"
53.8(W)�33.7(H) / 21(W)�13(H)
"
"
25"
"
"
"
Lens center
9.3/367
"
7.8/306
11.7/459
7.0/275
"
"
"
0.9/
37
"
5.8/229
"
"
1.1/
45
4.6/183
2.3/90
3.9/152
3.1/121
1.5/60
m/inch)
:
(Unit
Distance
TIP:
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
101
6. Installation and Connections
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.
Distance Chart
C
B = Vertical distance between lens center and
screen center
C = Throw distance
D = Vertical distance between lens center and
Screen center
screen bottom (top of screen for ceiling ap-
plication)
α = Throw angle
B
Lens center
α
D
NOTE: The values in the tables are design values and
may vary.
Screen bottom
[M361X/M311X/M271X]
α
Screen Size
Width
C
B
D
Diagonal
Height
wide
tele
wide
degree
11�4
11�3
11�1
11�0
10�9
10�9
10�9
10�9
10�8
10�8
10�8
10�8
10�8
10�8
10�7
10�7
10�7
tele
degree
6�7
6�7
6�6
6�6
6�6
6�6
6�6
6�6
6�5
6�5
6�5
6�5
6�5
6�5
6�5
6�5
6�5
inch
25
30
mm
635
762
inch
20
24
mm
508
610
inch
15
18
mm
381
457
inch
5
6
mm
131
157
210
314
377
419
440
471
524
629
786
943
1048
1100
1257
1414
1572
inch
26
31
42
64
77
86
90
97
108
130
162
195
217
228
261
294
327
mm
649
788
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
inch
44
53
mm
1107
1337
1798
2720
3273
3642
3827
4103
4564
5486
6869
8252
9174
9635
inch
-2
-3
-4
-6
-7
-8
-8
-8
mm
-60
-71
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240
813
24
36
610
914
8
1066
1622
1956
2178
2289
2456
2734
3290
4124
4958
5514
5792
6626
7460
8294
71
-95
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
12
15
17
17
19
21
25
31
37
41
43
50
56
62
107
129
143
151
162
180
216
270
325
361
379
-143
-171
-191
-200
-214
-238
-286
-357
-429
-476
-500
-572
-643
-714
43
48
50
54
60
72
90
108
120
126
144
162
180
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572
-9
-11
-14
-17
-19
-20
-23
-25
-28
434 11018
488 12401
543 13784
[M311W/M271W]
α
Screen Size
Width
C
B
D
Diagonal
Height
wide
tele
wide
degree
11�4
11�3
11�2
11�0
11�0
10�9
10�9
10�9
10�9
10�9
10�8
10�8
10�8
10�8
10�8
10�8
10�8
tele
degree
6�8
6�7
6�7
6�6
6�6
6�6
6�6
6�6
6�6
6�6
6�5
6�5
6�5
6�5
6�5
6�5
6�5
inch
25
30
mm
635
762
inch
21
25
mm
538
646
inch
13
16
mm
337
404
inch
5
7
mm
139
167
222
333
400
444
466
500
555
666
833
1000
1111
1166
1333
1499
1666
inch
27
33
44
67
81
90
95
102
114
137
171
206
229
240
275
310
344
mm
687
833
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
inch
46
56
mm
1172
1415
1902
2876
3461
3850
4045
4337
4824
5798
7259
8720
9694
inch
-1
-1
-2
-3
-3
-4
-4
-4
-5
-6
-7
-8
mm
-29
-35
-47
-71
-85
-94
-99
-106
-118
-141
-177
-212
-236
-247
-283
-318
-353
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
34
51
61
68
71
76
85
102
127
153
170
178
204
229
254
862
21
32
538
808
9
1126
1712
2064
2298
2415
2591
2884
3470
4349
5228
5814
6107
6986
7865
8744
75
1292
1551
1723
1809
1939
2154
2585
3231
3877
4308
4523
5169
5816
6462
13
16
17
18
20
22
26
33
39
44
46
52
59
66
113
136
152
159
171
190
228
286
343
382
38
42
45
48
53
64
79
95
106
111
127
143
159
969
1077
1131
1212
1346
1615
2019
2423
2692
2827
3231
3635
4039
-9
401 10181
458 11642
516 13103
573 14564
-10
-11
-13
-14
102
6. Installation and Connections
Reflecting the Image
WARNING
* Installing your projector on the ceiling must be done
by a qualified technician. Contact your NEC dealer for
more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
Using a mirror to reflect your projector’s image enables
you to enjoy a much larger image when a smaller space
is required. Contact your NEC dealer if you need a mirror
system. If you’re using a mirror system and your image
is inverted, use the MENU and buttons on your
projector cabinet or your remote control to correct the
• Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41°F (5°C) and 104°F (40°C) (Eco mode
selected automatically at 95°F to 104°F/35°C to
40°C).
• Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
• Ensure that you have adequate ventilation around
your projector so heat can dissipate. Do not cover the
vents on the side or the front of the projector.
103
6. Installation and Connections
Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power manage-
ment software.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
Connecting Your Computer
NOTE: Signals supported by Plug & Play (DDC2)
INPUT
COMPUTER 1 IN
analog
COMPUTER 2 IN
analog
HDMI
digital
Yes
Yes
Yes
USB(PC)
AUDIO IN
COMPUTER 1 IN
HDMI IN
Computer cable (VGA) (supplied)
To mini D-Sub 15-pin connector on the
projector. It is recommended that you use a
commercially available distribution amplifier
if connecting a signal cable longer than the
cable supplied.
A commercially available
USB cable
(compatible with USB 2.0
specifications)
Stereo mini-plug
audio cable (not
supplied)
NOTE: For Mac, use a commercially available
pin adapter (not supplied) to connect to your
Mac’s video port.
HDMI cable (not supplied)
Use High Speed HDMI®
Cable.
104
6. Installation and Connections
• Select the source name for its appropriate input connector after turning on the projector.
SOURCE button on the projector
Input connector
Button on the remote control
cabinet
COMPUTER 1 IN
COMPUTER 2 IN
HDMI IN
COMPUTER 1
COMPUTER 2
HDMI
(COMPUTER 1)
(COMPUTER 2)
HDMI
USB (PC)
USB DISPLAY
(USB DISPLAY)
NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ. button on the remote control or the projector cabinet.
105
6. Installation and Connections
Connecting an External Monitor
AUDIO OUT
MONITOR OUT (COMP. 1)
Stereo mini-plug audio cable
(not supplied)
Computer cable (VGA)
(not supplied)
Com-
puter cable
(VGA)
(supplied)
AUDIO
IN
PHONE
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer
analog image you’re projecting.
NOTE:
• Daisy chain connection is not possible.
• When audio equipment is connected, the projector speaker is disabled.
106
6. Installation and Connections
Connecting Your DVD Player or Other AV Equipment
Connecting Video/S-Video Input
VIDEO IN
S-VIDEO IN
AUDIO IN
S-Video cable (not supplied)
Video cable (not supplied)
Audio cable (not supplied)
Audio equipment
S-VIDEO VIDEO
VIDEO OUT
L
R
AUDIO IN
AUDIO OUT
L
R
Audio cable (not supplied)
• Select the source name for its appropriate input connector after turning on the projector.
SOURCE button on the projector
Input connector
Button on the remote control
cabinet
VIDEO IN
VIDEO
(VIDEO)
S-VIDEO IN
(S-VIDEO)
S-VIDEO
NOTE: The AUDIO IN L and R jacks (RCA) are shared between the Video and S-Video inputs.
NOTE: Refer to your VCR owner’s manual for more information about your equipment’s video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.
107
6. Installation and Connections
Connecting Component Input
COMPUTER 1 IN
AUDIO IN
15-pin - to - RCA (fe-
male) × 3 cable adapter
(ADP-CV1E)
Stereo mini plug - to - RCA audio
cable (not supplied)
Audio Equipment
Component video RCA × 3
cable (not supplied)
AUDIO IN
L
R
DVD player
L
R
Y
Cb Cr
Audio cable (not supplied)
AUDIO OUT
Component
A component signal will be automatically displayed. If not, from the menu, select [SETUP] → [OPTIONS(1)] →
[SIGNAL SELECT] → [COMPUTER1] or [COMPUTER2], and then place a check mark in the Component radio
button.
• Select the source name for its appropriate input connector after turning on the projector.
SOURCE button on the projector
Input connector
Button on the remote control
cabinet
COMPUTER 1 IN
COMPUTER 2 IN
COMPUTER 1
COMPUTER 2
(COMPUTER 1)
(COMPUTER 2)
NOTE: Refer to your DVD player’s owner’s manual for more information about your DVD player’s video output requirements.
108
6. Installation and Connections
Connecting HDMI Input
You can connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the
HDMI IN connector of your projector.
NOTE: The HDMI IN connector supports Plug & Play (DDC2B).
HDMI IN
HDMI
HDMI cable (not supplied)
Use High Speed HDMI®
Cable.
I
M D H
S-VIDEO VIDEO
L
R
AUDIO IN
VIDEO OUT AUDIO OUT
HDMI OUT
L
R
HDMI Output
Audio cable (not supplied)
SOURCE button on the projector
cabinet
Input connector
HDMI IN
Button on the remote control
HDMI
HDMI
TIP: For users of audio video equipment with an HDMI connector:
Select “Enhanced” rather than “Normal” if HDMI output is switchable between “Enhanced” and “Normal”.
This will provide improved image contrast and more detailed dark areas.
For more information on settings, refer to the instruction manual of the audio video equipment to be connected.
•
•
When connecting the HDMI IN connector of the projector to the DVD player, the projector’s video level can be
made settings in accordance with the DVD player’s video level. In the menu select [HDMI SETTINGS] → [VIDEO
LEVEL] and make necessary settings.
If the HDMI input sound cannot be heard, in the menu select [HDMI SETTINGS] → [AUDIO SELECT] →
[HDMI].
109
6. Installation and Connections
Connecting to a Wired LAN
The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable.
To use a LAN connection, you are required to set the LAN on the projector menu. Select [SETUP] → [WIRED LAN].
Example of LAN connection
Example of wired LAN connection
Server
Hub
LAN cable (not supplied)
NOTE: Use a Category 5 or higher LAN
cable.
LAN
110
6. Installation and Connections
Connecting to a Wireless LAN (Optional: NP02LM series)
The USB Wireless LAN Unit also provides a wireless LAN connection. To use a wireless LAN connection, you are
required to assign an IP address to the projector.
Important:
•
If you use the projector with the USB Wireless LAN Unit in the area where the use of wireless LAN equipment is
prohibited, remove the USB Wireless LAN Unit from the projector.
•
Buy the appropriate USB Wireless LAN Unit for your country or area.
NOTE:
• The green LED on the USB Wireless LAN Unit flashes to show that the USB Wireless LAN Unit is working.
• Your computer’s wireless LAN adapter (or unit) must be complied with Wi-Fi (IEEE802.11b/g/n) standard.
Flow of Setting Wireless LAN
Step 1: Attach the USB Wireless LAN Unit to the projector.
Access the HTTP server function to set [NETWORK SETTINGS] → [SETTINGS] → [WIRELESS] →
[EASY CONNECTION] , [PROFILE1] or [PROFILE2].
NOTE:
• To use the HTTP server function, the projector must be connected to a network.
First use the wired LAN to connect the projector to a network and then use the HTTP server to set the wireless LAN.
• After setting the wireless LAN by using the HTTP server, set [NETWORK SETTINGS] → [SETTINGS] → [WIRED] → [DISABLE]
When switching to set on the projector after connecting to the wireless LAN:
Use the menu to set the wireless LAN connection for the projector.
Select [DISABLE], [EASY CONNECTION] , [PROFILE1] or [PROFILE2] you set from the HTTP server.
Attaching the USB Wireless LAN Unit
NOTE:
• The USB Wireless LAN Unit must be inserted into the USB Wireless LAN Unit port in the correct direction. It cannot be inserted
in the reverse direction. If the USB Wireless LAN Unit is inserted in the reverse direction with excessive force applied, the USB
port may break.
• Before touching the USB Wireless LAN Unit, touch a metallic object (such as a door knob or aluminum window frame) to discharge
the static electricity from your body.
• Always insert or remove the USB Wireless LAN unit when the main power is turned off. Failure to do so may cause projector
malfunction or damage to the USB wireless LAN unit. If the projector will not work correctly, turn off the projector, disconnect
the power cord, and then connect it again.
• Do not insert other USB devices into the USB Wireless LAN unit port. Do not insert the USB Wireless LAN unit into the USB (PC)
port (Type B).
111
6. Installation and Connections
Prepare a Phillips screw driver beforehand.
1. Press the POWER button to turn off the projector and set it
into standby condition, and disconnect the power cord.
2. Remove the USB (LAN) port cover.
Loosen the screw securing the port cover.
• The screw is not removable.
3. Slowly insert the USB Wireless LAN Unit into the USB (LAN)
port.
Remove the cap from the USB Wireless LAN Unit, and then insert
it with the surface (side of indicator) facing outward. Keep the cap
for later use.
NOTE: Do not force to insert the USB Wireless LAN Unit.
4. Put the USB (LAN) port cover back into place.
Insert the catch of the USB (LAN) port cover into the groove of the
projector cabinet, and then tighten the screw to secure the port
cover.
WIREL
To remove the USB Wireless LAN Unit, disconnect the power cord
and use the above procedure.
NOTE:
• The green LED on the USB Wireless LAN Unit flashes to show that Wireless
LAN Unit is working. If the USB Wireless LAN Unit is incorrectly attached,
the blue LED will not flash.
• Do not press the button on the USB Wireless LAN Unit. The button will not
work with this model.
112
6. Installation and Connections
Example of wireless LAN connection
(Network Type → Infrastructure)
PC with wireless
LAN card inserted
PC with built-in wireless
LAN function
USB Wireless LAN Unit
Wireless access point
Wired LAN
Example of wireless LAN connection (Network Type → Ad Hoc)
USB Wireless LAN Unit
PC with wireless
LAN card inserted
PC with built-in wireless
LAN function
To enable direct communication (i.e., peer-to-peer) between personal computers and projectors, you need to
select the Ad Hoc mode.
113
7. Maintenance
This section describes the simple maintenance procedures you should follow to clean the filters, the lens, the cabinet,
and to replace the lamp and the filters.
1 Cleaning the Filters
The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter
is dirty or clogged, your projector may overheat.
NOTE: The message for filter cleaning will be displayed for one minute after the projector is turned on or off. When the message is
displayed, clean the filters. The time to clean the filters is set to [6000 H] at time of shipment on M311X/M271X/M271W; the time
to clean the filters is set to [5000 H] at time of shipment on M361X/M311W.
To cancel the message, press any button on the projector cabinet or the remote control.
The two-layer filter on the projector improves cooling and dust-proof capabilities compared with the conventional
models.
The outsides (intake side) of the first and second layer filters remove dust.
To clean the filter, detach the filter unit and the filter cover.
CAUTION
•
Before cleaning the filters, turn off the projector, disconnect the power cord and then allow the cabinet to cool.
Failure to do so can result in electric shock or burn injuries.
1. Push the button to release the filter unit and pull it out.
TIP:
The following explanation uses filters (fine-texture sponge and
coarse-texture sponge) attached to the projector at the time of
purchase as an example.
Button
After replacing with filters included in the optional lamp, replace the
words “fine-texture sponge and coarse-texture sponge” with “ac-
cordion soft and honeycomb hard” respectively.
I
2. Remove the filter cover.
Notch
The filter cover is fixed at six separate mounting points.
Bow the filter cover by pushing the notch slightly until it re-
leases.
Filter unit
Filter cover
Fine-texture
sponge
3. Remove the four filters and use a vacuum cleaner to
vacuum all the dust inside.
Get rid of dust in the sponge filter
NOTE:
• Whenever you vacuum the filter, use the soft brush attachment to
vacuum. This is to avoid damage to the filter.
• Do not wash the filter with water. Doing so can result in filter clog-
ging.
Coarse-texture sponge
114
7. Maintenance
4. Remove dust from the filter unit and the filter cover.
Clean both outside and inside.
Coarse-texture
sponge
5. Attach the four filters to the filter unit and the filter cover.
Filter unit: Attach two coarse-texture sponge filters (large and
small) to the filter unit.
Filter cover: Attach two fine-texture sponge filters (large and
small) to the filter cover.
The fine-texture sponge filter has slits on it. Align these slits
with the protrusions of the filter cover.
Fine-texture sponge
6. Attach the filter cover back to the filter unit
Align the filter unit with the filter cover and push the six protru-
sions into place.
•
Make sure all six mounting points are aligned properly.
7. Put the filter unit back to the projector cabinet.
Insert two catches of the tip of the filter unit into the groove of
the cabinet, and push the button to close the filter unit.
•
Push the filter unit until it clicks into place.
8. Clear the filter usage hours.
I
Plug the power cord into the wall outlet, and then turn on the
projector.
From the menu, select [RESET] → [CLEAR FILTER HOURS].
Groove
Button
The interval time to clean the filters is set to [OFF] at time of
shipment. When using the projector as it is, you do not clear
the filter usage
115
7. Maintenance
Cleaning the Lens
•
•
•
•
Turn off the projector before cleaning.
The projector has a plastic lens. Use a commercially available plastic lens cleaner.
Do not scratch or mar the lens surface as a plastic lens is easily scratched.
Never use alcohol or glass lens cleaner as doing so will cause damage to the plastic lens surface.
Cleaning the Cabinet
Turn off the projector, and unplug the projector before cleaning.
•
Use a dry soft cloth to wipe dust off the cabinet.
If heavily soiled, use a mild detergent.
•
•
Never use strong detergents or solvents such as alcohol or thinner.
When cleaning the vents or the speaker using a vacuum cleaner, do not force the brush of the vacuum cleaner
into the slits of the cabinet.
Vacuum the dust off the vents.
•
•
•
Clogged vents may cause a rise in the internal temperature of the projector, resulting in malfunction.
Do not scratch or hit the cabinet with your fingers or any hard objects
Contact your dealer for cleaning the inside of the projector.
NOTE: Do not apply volatile agent such as insecticide on the cabinet, the lens, or the screen. Do not leave a rubber or vinyl product
in prolonged contact with it. Otherwise the surface finish will be deteriorated or the coating may be stripped off.
116
7. Maintenance
Replacing the Lamp and the Filters
When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red and the message “THE
LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.” will appear
(*). Even though the lamp may still be working, replace the lamp to maintain the optimal projector performance. After
CAUTION
•
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector
off and then disconnect the power cord. Allow at least one hour for the lamp to cool before handling.
•
Use the specified lamp for safety and performance.
To order the replacement lamp, specify your lamp type.
Replacement lamp:
NP15LP: M311X/M271X/M271W
NP16LP: M361X/M311W
The replacement lamp comes with filters. While the filters attached to the projector at the time of purchase are
made of dark sponge material, the filters included with the optional lamp are made of non-woven white material.
There is no difference in performance between these two types.
•
•
DO NOT REMOVE ANY SCREWS except one lamp cover screw and two lamp housing screws.You could receive
an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might cause
an unwanted shadow and poor picture quality.
•
The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours
after the lamp has reached the end of its life. If this happens, be sure to replace the lamp. If you continue to use
the lamp after the lamp reaches the end of its life, the lamp bulb may shatter, and pieces of glass may be scattered
in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
*NOTE: This message will be displayed under the following conditions:
• for one minute after the projector has been powered on
• when the
(POWER) button on the projector cabinet or the POWER OFF button on the remote control is pressed
To turn off the message, press any button on the projector cabinet or the remote control.
Optional lamp and tools needed for replacement:
•
•
Phillips screwdriver (plus-head)
Replacement lamp
Flow of Replacing the Lamp and the Filters
Step 1. Replace the lamp
117
7. Maintenance
To replace the lamp:
1. Remove the lamp cover.
(1)Loosen the lamp cover screw
• The lamp cover screw is not removable.
(2)Push and slide the lamp cover off.
2. Remove the lamp housing.
(1)Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condi-
tion.
• The two screws are not removable.
• There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this
interlock.
(2)Remove the lamp housing by holding it.
CAUTION:
Make sure that the lamp housing is cool
enough to before removing it.
Interlock
118
7. Maintenance
3. Install a new lamp housing.
(1)Insert a new lamp housing until the lamp housing is plugged into the socket.
(2)Push the top center of the lamp housing to secure it.
(3)Secure it in place with the two screws.
• Be sure to tighten the screws.
4. Reattach the lamp cover.
(1)Slide the lamp cover back until it snaps into place.
(2)Tighten the screw to secure the lamp cover.
• Be sure to tighten the screw.
This completes the lamp replacement.
Go on to the filter replacement.
NOTE: When you continue to use the projector for another 100 hours after the lamp has reached the end of its life, the projector
cannot turn on and the menu is not displayed.
If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
119
7. Maintenance
To replace the filters:
Four filters are made of non-woven white material, packaged with the replacement lamp.
Honeycomb hard filter: Large and small sizes (attached to the filter unit)
Accordion soft filter: Large and small sizes (attached to the filter cover)
NOTE:
• Replace all four filters at the same time.
• Before replacing the filters, wipe off dust and dirt from the projector cabinet.
• The projector is precision equipment. Keep out dust and dirt during filter replacement.
• Do not wash the filters with soap and water. Soap and water will damage the filter membrane.
• Put filters into place. Incorrect attachment of a filter may cause dust and dirt to get into the inside of the projector.
TIP:
While the material of filters attached to the projector at the time of purchase is different from the material of filters included with the
optional lamp, there is no difference in performance between these two types.
1. Push the catch to release the filter unit and pull it out.
I
2. Detach the filter cover from the filter unit.
The filter cover is fixed at six separate mounting points.
Bow the filter cover by pushing it slightly until it releases.
Notch
Filter cover
Filter unit
120
7. Maintenance
3. Replace the four (4) filters
1. Remove the dark sponge filter, and then clean the filter unit and the filter cover.
2. Attach new, non-woven white material filters.
Filter unit: Attach two honeycomb hard filters to the filter unit.
Filter cover: Attach two accordion soft filters to the filter cover.
The accordion filter has slits on it. Align these slits with the protrusions of the filter cover.
4. Attach the filter cover back to the filter unit
Align the filter unit with the filter cover and push the protrusions into place.
• Make sure all six mounting points are aligned properly.
5. Put the filter unit back to the projector cabinet.
Insert two catches of the tip of the filter unit into the groove of the cabinet.
Push the filter unit until it clicks into place.
I
This completes the filter replacement.
Go on to the clearing lamp and filter hour meters.
To clear the lamp usage hours and the filter usage hours:
1. Place the projector where you use it.
2. Plug the power cord into the wall outlet, and then turn on the projector.
3. Clear the lamp usage hours and the filter usage hours.
1. From the menu, select [RESET] → [CLEAR LAMP HOURS] and reset the lamp usage hours.
121
8. Appendix
1 Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
Projector Condition
The main power is off
The projector is getting ready to turn on�
Note
Off
–
Blinking light
Blue
0�5 sec On,
Wait for a moment�
0�5 sec Off
2�5 sec On,
0�5 sec Off
Off Timer is enabled�
–
Steady light
Blue
Orange
Red
The projector is turned on�
[NORMAL] is selected for [STANDBY MODE]
[POWER-SAVING] is selected for [STANDBY –
MODE]
–
–
Status Indicator
Indicator Condition
Off
Projector Condition
Normal or Standby ([POWER-SAVING] for –
[STANDBY MODE])
Note
Blinking light
Red
1 cycle (0�5 sec Lamp cover error or lamp housing error
On, 2�5 sec Off)
Replace the lamp cover or lamp housing correctly�
2 cycle (0�5 sec Temperature error
On, 0�5 sec Off)
3 cycle (0�5 sec Power error
On, 0�5 sec Off)
4 cycle (0�5 sec Fan error
On, 0�5 sec Off)
The projector is overheated� Move the projector to
a cooler location�
Power unit is not working properly� Contact your
dealer�
Fans will not work correctly�
6 cycle (0�5 sec Lamp error
On, 0�5 sec Off)
Orange 1 cycle (0�5 sec Network conflict
On, 2�5 sec Off)
Lamp fails to light� Wait a full minute and then turn
on again�
Both the built-in wired LAN and the wireless LAN cannot
be connected to the same network at the same time�
To use both built-in wired LAN and wireless LAN at the
same time, connect them to different networks�
Green
Re-firing the lamp (The projector is cooling The projector is re-firing�
down�)
Wait for a moment�
Steady light
Green
Orange
Standby ([NORMAL] for [STANDBY MODE])
CONTROL PANEL LOCK is on�
–
You have pressed cabinet button when Control
Panel Lock is on�
Remote control ID and projector ID are not
matched�
CONTROL ID error
Lamp Indicator
Indicator Condition
Off
Red
Projector Condition
Note
Normal
–
Blinking light
Steady light
Lamp has reached its end of life� Lamp replace- Replace the lamp�
ment message will be displayed�
Lamp has been used beyond its limit� The projector Replace the lamp�
will not turn on until the lamp is replaced�
[ECO MODE] is set to [NORMAL] or [ECO]
Red
Green
–
Over-Temperature Protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp
with the STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
• Unplug the power cord after the cooling fans stop.
• Move the projector to a cooler location if the room where you are presenting is particularly too warm.
• Clean the vents if they are clogged with dust.
• Wait about 60 minutes until the inside of the projector becomes cool enough.
122
8. Appendix
Common Problems & Solutions
Problem
Check These Items
Does not turn on
or shut down
•
Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control
•
•
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room
where you are presenting is particularly warm, move the projector to a cooler location�
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters
or higher� Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a couple
•
•
•
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for
some time and then the projector will display the image� Wait for a moment�
Will turn off
No picture
•
•
Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select your
source (Computer, Video or S-Video)� (→ page 17) If there is still no picture, press the button again�
Ensure your cables are connected properly.
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (→ page 99)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC�
•
•
•
•
•
•
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up�
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software�
•
•
Picture suddenly be-
comes dark
Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,
Color tone or hue is un-
usual
•
•
Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (→ page 84)
Image isn’t square to the
screen
•
•
Picture is blurred
•
•
•
Ensure that the distance between the projector and screen is within the adjustment range of the lens.
•
•
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens�
Flicker appears on
screen
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600
meters or lower� Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTI-
TUDE] can cause the lamp to overcool, causing the image to flicker� Switch [FAN MODE] to [AUTO]� (→ page 89)
Image is scrolling ver-
tically, horizontally or
both
•
•
Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is supported
Remote control does
not work
•
•
•
Make sure there are no obstacles between you and the projector.
Indicator is lit or blink-
ing
•
Cross color in RGB
mode
•
•
For more information contact your dealer.
123
8. Appendix
If there is no picture, or the picture is not displayed correctly.
•
Power on process for the projector and the PC.
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”,
•
Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usu-
ally, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
•
•
Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each
notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step.
Refer to your computer’s documentation for detailed information.
Image displayed is incorrect when using a Mac
When using a Mac with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector) ac-
cording to your resolution. After setting, restart your Mac for the changes to take affect.
For setting display modes other than those supported by your Mac and the projector, changing the DIP switch on
a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch to
the 13" fixed mode and then restart your Mac. After that, restore the DIP switches to a displayable mode and then
restart the Mac again.
NOTE: A Video Adapter cable manufactured by Apple Inc. is needed for a MacBook which does not have a mini D-Sub 15-pin
connector.
•
•
Mirroring on a MacBook
*
When using the projector with a MacBook, output may not be set to 1024 × 768 unless “mirroring” is off on your
MacBook. Refer to owner’s manual supplied with your Mac computer for mirroring.
Folders or icons are hidden on the Mac screen
Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple
menu and arrange icons.
124
8. Appendix
Specifications
This section provides technical information about projector’s performance.
Optical
Model Number
NP-M361X
0.63 inch LCD with Micro Lens Array
(Aspect Ratio 4:3)
1024 × 768 pixels (XGA)
Manual zoom and focus
Zoom Ratio = 1.7
NP-M311X
NP-M271X
NP-M311W
NP-M271W
LCD Panel
0.63 inch LCD (As- 0.59 inch LCD with Micro Lens Array
pect Ratio 4:3)
(Aspect Ratio 16:10)
1280 × 800 pixels (WXGA)
Resolution*1
Lens
F1.7–2.1 f = 17.5–29.0 mm
Lamp
230 W AC
180 W AC
230 W AC
180 W AC
(170 W in NOR-
MAL)
(145 W in NORMAL)
(110 W in ECO)
(170 W in NOR-
MAL)
(145 W in NOR-
MAL)
(140 W in ECO)
3600 lumens
NORMAL: 75%
ECO: 60%*4
3000:1
(140 W in ECO)
3100 lumens
NORMAL: 75%
(110 W in ECO)
2700 lumens
NORMAL: 80%
Light Output*2*3
3100 lumens
NORMAL: 80%
2700 lumens
Contrast Ratio*3
(full white: full black)
Image Size (Diagonal) 25–300 inches/0.64 m–7.6 m
Projection Distance
(Min.–Max.)
26–543 inches/0.65–13.8 m
27–573 inches/0.69–14.6 m
Projection Angle
10.7°–11.4° (wide)/
6.5°–6.8° (tele)
10.8°–11.4° (wide)/
6.5°–6.8° (tele)
*1 Effective pixels are more than 99.99%.
*2 This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any other mode is selected as the
[PRESET] mode, the light output value may drop slightly.
*3 Compliance with ISO21118-2005
*4 The maximum power becomes equivalent to power in NORMAL (ECO MODE).
Electrical
Model Number
NP-M361X
NP-M311X
NP-M271X
NP-M311W
NP-M271W
Inputs
2 × RGB/Component (D-Sub 15 P), 1 × HDMI Type A (19P, HDMI® Connector) HDCP supported*5,
1 × S-Video (DIN 4 P), 1 × Video (RCA), 1 × (L/R) RCA Audio, 2 × Stereo Mini Audio
1 × RGB (D-Sub 15P), 1 × Stereo Mini Audio
Outputs
PC Control
1 × PC Control Port (D-Sub 9P)
1 × RJ-45 (10BASE-T/100BASE-TX)
IEE 802.11 b/g/n (optional USB Wireless LAN Unit required)
Wired LAN Port
Wireless LAN Port
(Optional)
USB Port
Color Reproduction
1 × Type A, 1 × Type B
10-bit signal processing (1.07 billion colors) (HDMI, VIEWER, NETWORK: Colors, 16.7 million colors)
Compatible Signals*6 Analog: VGA/SVGA/XGA/WXGA/WXGA+/SXGA/SXGA+/UXGA/WUXGA
480i/480p/576i/576p/720p/1080i/1080p
HDMI: VGA/SVGA/XGA/WXGA/SXGA/480p/576p/720p/1080i/1080p
RGB: 80 MHz (Max.)
Video Bandwidth
Horizontal Resolution 540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60
300 TV lines: SECAM
Scan Rate
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 120 Hz (HDMI: 50 Hz to 85 Hz)
Separate Sync
Sync Compatibility
*5 HDMI® (Deep Color, Lip Sync) with HDCP
What is HDCP/HDCP technology?
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a system
for preventing illegal copying of video data sent over a High-Definition Multimedia Interface (HDMI).
If you are unable to view material via the HDMI input, this does not necessarily mean the projector is not functioning properly.With
the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed
due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
Video: Deep Color; 8/10/12-bit, LipSync
Audio: LPCM; up to 2 ch, sample rate 32/44.1/48 KHz, sample bit; 16/20/24-bit
*6 An image with higher or lower resolution than the projector’s native resolution (M361X/M311X/M271X: 1024 × 768 / M311W/
M271W: 1280 × 800) will be displayed with Advanced AccuBlend.
125
8. Appendix
Model Number
Built-in Speaker
Power Requirement
Input Current
NP-M361X
NP-M311X
NP-M271X
NP-M311W
NP-M271W
10W (monaural)
100–240V AC, 50/60Hz
3.4 A/1.5 A
311 W
(100-130 V)/
302 W
2.8 A/1.2 A
248 W (100-130 V)
239 W (200-240 V)
3.4 A/1.5 A
311 W
(100-130 V)/
302 W
2.8 A/1.2 A
248 W
(100-130 V)/
239 W
Power
Consump- MODE
tion OFF
ECO
(200-240 V)
NORMAL 239 W
(100-130 V)/
(200-240 V)
239 W
(100-130 V)/
236 W
(200-240 V)
198 W
(100-130 V)/
193 W
198 W (100-130 V)
193 W (200-240 V)
236 W
(200-240 V)
213 W (100-130 V) 176 W (100-130 V)
211 W (200-240 V) 172 W (200-240 V)
(200-240 V)
213 W (100-130 V) 176 W (100-130 V)
211 W (200-240 V) 172 W (200-240 V)
(200-240 V)
ECO
STANDBY 8 W (100-130 V/200-240 V)
(NORMAL)
STANDBY 0.2 W (100-130 V)/0.4 W (200-240 V)
(POWER-
SAVING)
Mechanical
Model Number
Installation
NP-M361X
NP-M311X
NP-M271X
NP-M311W
NP-M271W
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Orientation
Dimensions
13.4" (W) × 3.9" (H) × 10.1" (D) /339 mm (W) × 99 mm (H) × 257 mm (D)
(not including protrusions)
Weight
Environmental
Considerations
6.59 lbs/2.99 kg
Operational Temperatures : 41° to 104°F (5° to 40°C),
(ECO mode selected automatically at 95°F to 104°F/35°C to 40°C)
20% to 80% humidity (non-condensing)
6.39 lbs/2.9 kg
6.59 lbs/2.99 kg
6.39 lbs/2.9 kg
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
UL/C-UL Approved (UL 60950-1, CSA 60950-1)
Meets DOC Canada Class B requirements
Regulations
Meets FCC Class B requirements
Meets AS/NZS CISPR.22 Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)
For additional information visit:
For information on our optional accessories, visit our website or see our brochure.
The specifications are subject to change without notice.
126
8. Appendix
Pin Assignments of D-Sub COMPUTER Input Connector
Mini D-Sub 15 Pin Connector
Pin No.
RGB Signal (Analog)
YCbCr Signal
11 12 13 14 15
1
2
Red
Cr
Y
6
7
8
9
10
Green or Sync on Green
Blue
Ground
Ground
Red Ground
Green Ground
Blue Ground
No Connection
Sync Signal Ground
No Connection
Bi-directional DATA (SDA)
Horizontal Sync or Composite
Sync
1
2
3
4
5
3
Cb
4
5
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
6
Cr Ground
Y Ground
Cb Ground
7
8
9
10
11
12
13
14
15
Vertical Sync
Data Clock
COMPUTER 1 IN
NOTE: Pin Nos. 12 and 15 are required for DDC/CI.
128
8. Appendix
Compatible Input Signal List
Analog RGB
HDMI
Resolution
( dots )
640 × 480
Refresh Rate
( Hz )
60/72/75/85/
iMac
56/60/72/75/85/
iMac
60/70/75/85/
Resolution
( dots )
640 × 480
800 × 600
Refresh Rate
Signal
VGA
Aspect Ratio
4:3
Signal
Aspect Ratio
( Hz )
60
60
60
60
60
60
60
60
60
60
60
VGA
SVGA
XGA
4:3
4:3
4:3
15:9
16:10
16:9
4:3
1024 × 768 *1
1280 × 768 *2
1280 × 800 *2
1366 × 768
1280 × 960
1280 × 1024
1400 × 1050
1440 × 900
1600 × 900
1680 × 1050
1920 × 1080
1920 × 1080
1280 × 720
720 × 480
SVGA
XGA
800 × 600
4:3
4:3
WXGA
1024 × 768 *1
iMac
60
60
60
60
60/75
60/75
60
60
60
60
60
60
60
60
67
75
75
WXGA
1280 × 768 *2
1280 × 800 *2
1360 × 768 *3
1366 × 768 *3
1280 × 960
1280 × 1024
1400 × 1050
1440 × 900
1600 × 900 *3
1600 × 1200
1680 × 1050
1280 × 720
1920 × 1080
1920 × 1200
640 × 480
15:9
16:10
16:9
16:9
4:3
Quad-VGA
SXGA
SXGA+
WXGA+
WXGA++
5:4
4:3
16:10
16:9
16:10
16:9
16:9
16:9
4:3/16:9
4:3/16:9
Quad-VGA
SXGA
SXGA+
WXGA+
WXGA++
UXGA
5:4
4:3
WSXGA+
60
HDTV (1080p)
HDTV (1080i)
HDTV (720p)
SDTV (480p)
SDTV (576p)
50/60
50/60
50/60
60
16:10
16:9
4:3
16:10
16:9
16:9
16:10
4:3
4:3
4:3
4:3
5:4
WSXGA+
HD
720 × 576
50
Full HD
WUXGA
MAC 13"
MAC 16"
MAC 19"
MAC 21"
MAC 23"
832 × 624
1024 × 768
1152 × 870
1280 × 1024
75
65
Component
Refresh Rate
( Hz )
Signal
Format
Aspect Ratio
HDTV (1080p)
HDTV (1080i)
HDTV (720p)
SDTV (480p)
SDTV (576p)
SDTV (480i)
SDTV (576i)
1920 × 1080
1920 × 1080
1280 × 720
720 × 480
720 × 576
720 × 480
720 × 576
16:9
16:9
16:9
4:3/16:9
4:3/16:9
4:3/16:9
4:3/16:9
50/60
50/60
50/60
60
50
60
50
Composite Video/S-Video
Refresh Rate
( Hz )
Signal
Aspect Ratio
*1 Native resolution on XGA model (M361X/M311X/M271X)
*2 Native resolution on WXGA model (M311W/M271W)
*3 The projector may fail to display these signals correctly when [AUTO]
is selected for [ASPECT RATIO] in the on-screen menu.
The factory default is [AUTO] for [ASPECT RATIO]. To display these
signals, select [16:9] for [ASPECT RATIO].
NTSC
PAL
PAL60
SECAM
4:3
4:3
4:3
4:3
60
50
60
50
NOTE:
• An image with higher or lower resolution than the projector’s native resolution (M361X/M311X/M271X: 1024 × 768 / M311W/
M271W: 1280 × 800) will be displayed with Advanced AccuBlend.
• Sync on Green and Composite sync signals are not supported.
• Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
129
8. Appendix
PC Control Codes and Cable Connection
PC Control Codes
Function
Code Data
POWER ON
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
02H
02H
02H
02H
02H
02H
02H
02H
00H
00H
00H
00H
02H
03H
01H
01H
01H
01H
01H
01H
01H
01H
12H
13H
14H
15H
POWER OFF
01H
03H
03H
03H
03H
03H
03H
03H
03H
10H
11H
12H
13H
INPUT SELECT COMPUTER 1
INPUT SELECT COMPUTER 2
INPUT SELECT HDMI
INPUT SELECT VIDEO
INPUT SELECT S-VIDEO
INPUT SELECT VIEWER
INPUT SELECT NETWORK
INPUT SELECT USB DISPLAY
PICTURE MUTE ON
PICTURE MUTE OFF
SOUND MUTE ON
01H
02H
1AH
06H
0BH
1FH
20H
22H
09H
0AH
22H
0EH
13H
27H
28H
2AH
SOUND MUTE OFF
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
Cable Connection
Communication Protocol
Baud rate �����������������������������������������38400 bps
Data length ��������������������������������������8 bits
Parity�����������������������������������������������No parity
Stop bit��������������������������������������������One bit
X on/off��������������������������������������������None
Communications procedure�������������Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
PC Control Connector (D-SUB 9P)
To TxD of PC
To RxD of PC
To GND of PC
1
2
3
4
5
6
7
8
9
To RTS of PC
To CTS of PC
NOTE 1: Pins 1, 4, 6 and 9 are no used.
NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.
130
8. Appendix
Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem
more efficiently.
* Print this page and the next page for your check.
Frequency of occurrence always sometimes (How often?_____________________) other (__________________)
Power
No power (POWER indicator does not light blue) See also “Status
Shut down during operation�
Indicator (STATUS)”�
Power cord’s plug is fully inserted into the wall outlet�
Power cord’s plug is fully inserted into the wall outlet�
Lamp cover is installed correctly �
Main power switch is pressed to the ON position�
[AUTO POWER OFF] is turned off (only models with the [AUTO
Lamp cover is installed correctly �
POWER OFF] function)�
Lamp Hours Used (lamp operation hours) was cleared after
[OFF TIMER] is turned off (only models with the [OFF TIMER]
lamp replacement�
function)�
No power even though you press and hold the POWER but-
ton�
Video and Audio
No image is displayed from your PC or video equipment to the
projector�
Parts of the image are lost�
Still unchanged even though you press the AUTO ADJUST
button�
Still unchanged even though you carry out [RESET] in the
projector’s menu�
Still no image even though you connect the projector to the PC
first, then start the PC�
Enabling your notebook PC’s signal output to the projector�
•
A combination of function keys will enable/disable the exter-
nal display. Usually, the combination of the “Fn” key along
with one of the 12 function keys turns the external display
on or off.
Image is shifted in the vertical or horizontal direction�
Horizontal and vertical positions are correctly adjusted on a
computer signal�
Input source’s resolution and frequency are supported by the
projector�
No image (blue or black background, no display)�
Still no image even though you press the AUTO ADJUST
button�
Still no image even though you carry out [RESET] in the
projector’s menu�
Signal cable’s plug is fully inserted into the input connector
A message appears on the screen�
( _____________________________________________ )
The source connected to the projector is active and available�
Still no image even though you adjust the brightness and/or
the contrast�
Some pixels are lost�
Image is flickering�
Still unchanged even though you press the AUTO ADJUST
button�
Still unchanged even though you carry out [RESET] in the
projector’s menu�
Image shows flickering or color drift on a computer signal�
Still unchanged even though you change [FAN MODE] from
[HIGH ALTITUDE] to [AUTO]�
Image appears blurry or out of focus�
Input source’s resolution and frequency are supported by the
projector�
Still unchanged even though you checked the signal’s resolution
on PC and changed it to projector’s native resolution�
Still unchanged even though you adjusted the focus�
No sound�
Image is too dark�
Remains unchanged even though you adjust the brightness
and/or the contrast�
Image is distorted�
Audio cable is correctly connected to the audio input of the
projector�
Still unchanged even though you adjusted the volume level�
Image appears to be trapezoidal (unchanged even though you
carry out the [KEYSTONE] adjustment)�
AUDIO OUT is connected to your audio equipment (only models
with the AUDIO OUT connector)�
Other
Remote control does not work�
Buttons on the projector cabinet do not work (only models with the
[CONTROL PANEL LOCK] function)
No obstacles between the sensor of the projector and the
remote control�
Projector is placed near a fluorescent light that can disturb the
infrared remote controls�
[CONTROL PANEL LOCK] is not turned on or is disabled in
the menu�
Still unchanged even though you press and hold the EXIT button
for a minimum of 10 seconds�
Batteries are new and are not reversed in installation�
131
8. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
Projector
Installation environment
Screen size:
Model number:
Serial No�:
inch
Screen type: White matte Beads Polarization
Date of purchase:
Lamp operating time (hours):
Eco Mode:
Wide angle High contrast
Throw distance:
feet/inch/m
OFF AUTO ECO
Orientation: Ceiling mount Desktop
Power outlet connection:
NORMAL ECO
Information on input signal:
Horizontal synch frequency
Vertical synch frequency
Synch polarity
Connected directly to wall outlet
[
[
] kHz
] Hz
Connected to power cord extender or other (the
number of connected equipment______________)
Connected to a power cord reel or other (the number
H (+) (−)
of connected equipment______________)
V (+) (−)
Synch type
Separate Composite
Sync on Green
Computer
Manufacturer:
STATUS Indicator:
Steady light
Model number:
Notebook PC / Desktop
Native resolution:
Refresh rate:
Orange Green
Flashing light
[
]] cycles
Remote control model number:
Video adapter:
Other:
PC
Projector
DVD player
Video equipment
VCR, DVD player, Video camera, Video game or other
Signal cable
Manufacturer:
Model number:
NEC standard or other manufacturer’s cable?
Model number:
Distribution amplifier
Model number:
Switcher
Length:
inch/m
Model number:
Adapter
Model number:
132
8. Appendix
TCO Certification
Some models in this product family are TCO certified. All TCO certified models have the TCO mark on the marking
plate (on the bottom of the product).To see a list of our TCO certified projectors and their TCO Certification (in English
The TCO certification, designed by TCO Development, is an international environmental and ergonomics standard
for IT equipment.
In some cases we may post a list of TCO certified models on our website before the TCO mark is placed on the prod-
uct.This difference in timing is related to the date certification is received compared with the projectors manufacturing
date.
133
8. Appendix
REGISTER YOUR PROJECTOR! (for residents in the United
States, Canada, and Mexico)
Please take time to register your new projector. This will activate your limited parts and labor warranty and InstaCare
service program.
Visit our web site at www.necdisplay.com, click on support center/register product and submit your completed form
online.
Upon receipt, we will send a confirmation letter with all the details you will need to take advantage of fast, reliable
warranty and service programs from the industry leader, NEC Display Solutions of America, Inc.
134
© NEC Display Solutions, Ltd. 2012
7N951851
|