MAYTAG MDB8979SE User Manual

Undercounter Dishwasher  
PRODUCT MODEL NUMBERS  
PRODUCT DIMENSIONS  
MDB8969SD MDB8959SF  
MDB8979SE MDB8979SF  
MDB4949SD MDB6949SD  
MDB5969SD MDB7949SD  
23  
(60.6 cm)  
"
"
Electrical Requirements:120-volt, 60 Hz, AC-only,  
15- or 20-amp. fused electrical supply. Copper wire only.  
A time delay fuse or circuit breaker and separate circuit  
is recommended.  
24  
(62.2 cm)  
B
If direct wiring dishwasher: Use flexible, armored  
or nonmetallic, sheathed copper  
wire with grounding wire that  
C
meets the wiring requirements for  
your home and local codes and ordinances.  
Use a UL Listed or CSA Approved conduit connector.  
If connecting dishwasher with a power supply cord:  
Use power supply cord kit (Part  
Number 4317824) marked for use  
"
(1.9 cm)  
A
30"  
(76.2 cm)  
with dishwashers. Follow the kit  
instructions for installing the power supply cord.  
Power supply cord must plug into a grounded  
3 prong outlet located in the cabinet next to the  
dishwasher opening. Outlet must meet all local  
codes and ordinances.  
"
33  
Water Supply Requirements: A hot water line with 20 to  
120 psi (138 to 862 kPa) water pressure. Water temperature  
must be 120°F (49°C) water at dishwasher. Use 3/8" O.D.  
copper tubing with compression fitting or flexible braided  
water supply line.  
(85,1wcimth)  
min.  
ed  
v
wheels  
remo  
Note: " minimum plastic tubing is not recommended.  
Use a 90° elbow with " hose connection with rubber  
washer (Part Number W10273460). Do not solder  
within 6" (15.2 cm) from water inlet valve.  
Drain Requirements:A new drain hose is supplied with  
your dishwasher. If this is not long enough, use a new  
drain hose with a maximum length of 12' (3.7 m) (Part  
Number 3385556) that meets all current AHAM/IAPMO  
test standards, is resistant to heat and detergent, and  
fits the 1" (2.5 cm) drain connector of the dishwasher.  
"
21  
(53.3 cm)  
3
" - 4  
"
"
(8.8 cm - 10.6 cm)  
For 4" (10 cm)  
toekick, height of  
cabinet opening is  
341/2" (86.3 cm).  
(9.4 cm)  
Make sure to connect the drain hose to waste tee or disposer  
inlet above drain trap in house plumbing and 20" (50.8 cm)  
minimum above the floor. It is recommended that the  
drain hose either be looped  
air gap  
A. Insulation may be compressed  
(not used on all models).  
up and securely fastened to  
the underside of the counter  
or be connected to an air gap.  
B. For panel-ready models, dishwasher  
depth is 24" (60 cm) not including the  
" (1.9 cm) custom door panel.  
Make sure to use an air  
gap if the drain hose is  
connected to house  
plumbing lower than  
20" (50.8 cm) above  
C. Door handles may protrude forward  
of the face of the dishwasher; varies  
by model.  
floor.  
subfloor or  
Use 1/2" (1.3 cm) minimum I.D. drain line fittings.  
If required, the air gap should be installed in accordance  
with the air gap installation instructions. When connecting  
the air gap, a rubber hose (not provided) will be needed  
toconnect to the waste tee or disposer inlet.  
Page 1 of 2  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
W10741197A-D-MT  
12/2016  

Trane Intellipak Rt Svx10c En User Manual
Ricoh Aficio 3035 User Manual
NEC MULTISYNC LCD1770NX User Manual
MAKITA UC3050A User Manual
KENWOOD M 720DAB User Manual
HITACHI 51F59A User Manual
DIGIUM TE121 User Manual
DBTECHNOLOGIES VIO L1610 User Manual
CRAFTSMAN 917.271832 User Manual
ACER ASPIRE T630 User Manual