LG CINEBEAM PF610P CB User Manual

OWNER'S MANUAL

DLP Projector

Please read the safety information carefully before using this product.

PF610P (PF610P-SA)

PF610P (PF610P-CB)

www.lg.com

P/NO : SAC38518907 (2109-REV00)

PREPARATION

The pictures may differ slightly from the actual product.

Accessories

Accessories included with the projector are show below.

Accessories are subject to change without prior notice.

New accessories may be added or old ones removed.

Remote Control

Two AAA Batteries

Owner's Manual

Power cord

AC-DC Adaptor

AAA: Due to the environment government regulations about import and

batteries destruction in Colombia, projectors will not bring the batteries of

remote control included.

• When connecting an HDMI or USB cable, or

connecting a USB flash drive to the HDMI

or USB port, use a product that has a width

of 18 mm or less and a height of 10 mm or

less. If the USB cable or USB flash drive does

not fit the USB ports of the projector, use an

A ≤ 10 mm

B ≤ 18 mm

extension cable that supports USB 2.0.

• When connecting two USB devices at the same time, each one should have

bezels less than 8.5 mm thick.

• Use a certified cable with the HDMI logo attached.

• If you do not use a certified HDMI cable, the screen may not display or a

connection error may occur. (Recommended HDMI cable types)

— Ultra High Speed HDMI^®/™ Cable (3 m or less)

Optional Extras

To purchase optional accessories, visit an electronics store or online shopping site or

contact the retail store where you purchased the product. Optional accessories are

subject to change without prior notice.

Projection Screen

Tripod

LG Audio Device

HDMI Cable

Optical Cable

Parts and Components

Joystick Button

Focus Knob

Inlet Vent

Lens¹⁾

1) Do not touch the lens when using the projector. The lens may be damaged. (Keep

lens away from sharp objects.)

Outlet Vent¹⁾

Speaker

Bottom of the Projector

Adjustable leg²⁾

1) Due to the high temperature of vent area, do not get close to the vent area.

2) Turn the adjustable leg left or right to adjust the angle.

(DC IN Port)

Port

(Headphone Port)

IR Receiver

Using the Joystick Button

You can operate the projector by pressing the button or moving the joystick left, right,

up, or down.

Basic functions

When the projector is turned off, place your

Power On

ﬁnger on the joystick button, press it once, and

release it.

Power Off

(Press and

Hold)

Press and hold the joystick button for more than

3 seconds while the projector is on.

Place your ﬁnger over the joystick button and

move it left or right, you can adjust the volume

level.

Volume

Control

If you move the joystick up, down, left, or right,

you can move the cursor to select the menu

items.

Up/Down/

Left/Right

NOTE

• When moving the joystick button up, down, left or right, be careful not to move

the button while it is being pressed. The volume may not be adjusted and the

cursor may not move when the joystick button is pressed and moved.

Adjusting the menu

When the projector is turned on, press the joystick button one time.

You can adjust the menu items moving the joystick button left, right, up, or down. Move

to the desired menu item, and then press the joystick button once to select it.

Turns the power off.

Changes the input source.

Clears on-screen displays and returns to projector viewing.

Displays the Settings menu.

Projector Status Indicators

LED Power Indicator

Power standby state

The projector is operating with the power on.

Red

Off

INSTALLATION

Ceiling-Type Installation

WARNING

When installing the product on the ceiling, observe the following precautions

to prevent the projector from falling:

— It is recommended to install the product through a professional installation

services provider. (If installing on the ceiling, modify the projector’s PJT Mode

settings)

— Do not use adhesive, lubricant, oil, etc. when using the mounting equipment.

— Do not tighten the screws with an excessive force since the projector may fall

due to breakage of the screw connection part.

— Standard screw: M4 x 8 mm, M6 x 10 mm, 1/4-20 UNC x 5 mm

(Applicable screw types may vary depending on the model.)

— Recommended torque: 5-8 kgf.cm (4.34-6.94 lbf-in)

• A failure to follow the precautions may result in injury or death and product

damage due to the fall of the product.

How to Install the Projector On a Tripod

• You can install the projector using a camera tripod.

• As shown below, you can mount the projector instead of a camera on the tripod.

• When stabilizing the tripod, we recommend using a locking bolt of standard size

4.5 mm or less. The maximum size allowed for the locking bolt is 5.5 mm. (If it is

longer than the maximum allowed size, it may damage the projector.)

Bolt used to attach the

projector to the tripod

Bottom of the

Projector

The projector is

connected to this part.

Tripod

CAUTION

• If you are using a tripod, be careful not to apply external force to the tripod.

Doing so may damage the projector.

• Do not place the tripod on an unstable surface.

• Be sure to use a tripod with a maximum load capacity of 3 kg or more.

• To use the projector safely, position the tripod legs so that they are as wide and

stable as possible and be sure to securely attach the projector to the tripod.

Projection Distance per Screen Size

1 Place the projector on a sturdy, level surface, together with the PC or audio/

video source.

2 Place the projector an appropriate distance away from the screen. The distance

between the projector and the screen determines the actual size of the image.

3 Position the projector so that the lens is at a right angle to the screen. If the

projector is not at a right angle, the projected image will look distorted. To

correct the distortion, use the Edge Adjustment function.

4 Connect the power cord of the projector and the connected device to the wall

outlet.

Ratio of upward projection: 100 %

Screen

Projection Distance (D)

16:9 Aspect Ratio

Projection

Distance (D)

Screen Size

inches mm

Screen Width (Y) Screen Height (X)

1524

1651

1778

1905

2032

2159

2286

2413

2540

2667

2794

2921

3048

1328

1439

1550

1660

1771

1882

1992

2103

2214

2324

2435

2546

2657

747

809

1588

1720

1853

1985

2117

2249

2382

2514

2647

2779

2911

3043

3176

872

934

996

1058

1121

1183

1245

1308

1370

1432

1494

100

105

110

115

120

The projection distance may vary depending on the installation conditions.

NOTE

• If the projected image looks distorted or bent, check to see if the screen is

installed properly.

Adjusting the Focus of the Projection Screen

When an image appears on the screen, check if it is in focus and ﬁts the screen

properly.

To adjust the focus of the image, slowly adjust the focus knob to the left or right while

looking at the top center of the screen. You can adjust the focus most effectively when

the left and right screen are balanced. When adjusting the focus on the screen, do not

let the product shake.

Focus Knob

NOTE

• After using the product at room temperature, turning on the power may blur the

focus if the inside temperature is low, but it will recover over time.

• This defocusing is a temporary phenomenon that occurs in low-temperature

environments, and this will not affect the product’s performance or lifespan.

Kensington Security System

• This projector has a Kensington Security Standard connector as an anti-theft

mechanism. Connect a Kensington Security System cable as shown below.

• For more information on installation and use of the Kensington Security System,

refer to the user’s guide provided with the Kensington Security System.

• The Kensington Security System is an optional accessory.

• What is Kensington?

Kensington is a company that provides safety systems for laptops and other

electronic devices. Website: http://www.kensington.com

USING REMOTE CONTROL

Inserting Batteries in the Remote Control

Use 1.5 V, AAA-type alkaline batteries. Replace the two batteries with new ones and

insert them according to the direction indicator inside the remote control.

1 Remove the battery cover on the back

of the remote control by sliding it

downwards.

2 Insert the batteries to match the +, -

polarity symbols.

3 Close the battery cover.

CAUTION

• Do not mix new batteries with old ones.

Viewing the Remote Control Features

* : To use the button, press and hold for more than 3 seconds.

(POWER)

Turns the Projector on or off.

(INPUT)

Changes the input source.

(Picture Mode)

Changes the [Picture Mode].

(Sound Mode)

Changes the [Sound Mode].

(Aspect Ratio)

Changes the [Aspect Ratio].

(Energy Saving)

Reduces power consumption by adjusting peak

screen brightness.

Number buttons

Enters numbers.

— Pressing and holding the

the [Quick Help] menu.

button displays

Edits QUICK ACCESS.

(QUICK ACCESS is a feature that allows you to enter

a speciﬁed app directly by pressing and holding the

number buttons.)

Change the input source to [HDMI 1].

Change the input source to [HDMI 2].

Adjusts the volume level.

Shows information on the current screen.

(SEARCH)

Shows the search mode.

(MUTE)

Mutes all sounds.

(MUTE) *

Accesses the [Accessibility] menu.

Moves to the previous/next page.

Streaming Service buttons

Connects to the Video Streaming Service.

Accesses the Home menu.

Displays the list used previously.

(MORE ACTIONS)

Displays more remote control functions.

(OK)

Selects menus or options and conﬁrms your input.

(Q. Settings)

Accesses the Quick Settings.

(Back)

Returns to the previous screen.

(EXIT)

Exits the menu.

(Control buttons)

Controls media contents.

These access special functions in some menus.

NOTE

• When using the remote control, the optimal operation range is 6 meters or less

(left/right) and within a 30 degree arc of the remote control IR receiver.

• If a cable is connected to the back port, the optimal operating range is 3 meters

or less (left/right) and within a 30 degree arc of the remote control IR receiver.

• For seamless operation, do not block the IR receiver.

• When you carry the remote control in the portable bag, make sure that

the buttons on the remote control are not pressed by the projector, cables,

documents, or any other accessories in the bag. Otherwise, it may significantly

reduce the battery life.

CONNECTING DEVICES

You can connect various external devices to the projector.

Connecting with a HDMI Cable

Connect an HD receiver, DVD, PC, Notebook, or external devices to the projector and

select an appropriate input mode.

With an HDMI cable, you can enjoy high quality picture and sound.

Using a HDMI cable, connect the

port of the projector to the HDMI output port

of the device to connect. Both video and audio are output at the same time.

•

(INPUT) [Home Dashboard] [Inputs] [HDMI 1]/[HDMI 2]

Optional Extras

NOTE

ARC (Audio Return Channel)

• External audio devices that support SIMPLINK and ARC must be connected

using

port. (

)

• When connected with a Ultra High Speed HDMI^®/™ Cable, external audio

devices that support ARC output or SPDIF work with the SIMPLINK function

without the need for an additional optical audio cable.

When connecting PC/laptop

• The projector supports Plug and Play. Your PC will automatically detect the

projector and requires no driver installation.

Connecting a Digital Amp

Using an optical cable, connect the digital audio input port of a digital amp to the

port of the projector. The output of an amp with a

digital converter must be set to the desired audio format. When using a HDMI cable

to connect a home theater or when connecting an optical output to an external audio

device, set [Sound Out] to [Optical]. If a projector, home theater, or the speaker of an

external audio device is operating at the same time, there will be an echo.

Optional Extras

NOTE

• Refer to the user manual of the audio device to connect.

• When connecting this product to other devices, make sure to turn off and

unplug all the devices.

• The audio output of this product has wide-ranging audio bandwidth, so the

receiver volume must be adjusted properly. Speakers can be damaged by

unexpected high frequencies.

• Connecting the

port of the projector to the

digital audio input port of a digital amp and the audio input port of the projector

to the analog audio output port of the digital amp can cause sound oscillation

due to the closed loop. Remove one of the two connections to prevent this. (This

also applies to home theater devices.)

Connecting Headphones

You can listen to the audio through a headphone.

Optional Extras

Connecting a smart device (smartphone, tablet,

etc.)

•

(INPUT) [Home Dashboard] [Inputs] [HDMI 1]/[HDMI 2]

• The picture may look different from the actual product.

Connect a smart device to the projector using a cable¹⁾and set the external input of

the projector to HDMI. The smart device screen will then be displayed through the

projector. You can connect with any HDMI input port.

For model-speciﬁc instructions regarding use of the wired connection, please check

with the smart device manufacturer.

Supported smart devices may change depending on the circumstances of each

manufacturer.

1) Examples of how to connect a cable to different smart devices (cable purchased

separately).

Slimport supported devices

Charging port of a

smart device

HDMI cable

Slimport adapter

Charging

cable of

a smart

device

Projector HDMI port

Projector USB port

Charger

Apple Lightning Digital AV adapter supported devices

HDMI cable

Lightning Digital AV

adapter

Projector HDMI port

Charging port of a smart device

Apple 30-pin Digital AV adapter supported devices

HDMI cable

Apple 30-pin Digital

AV adapter

Projector HDMI port

Charging port of a smart device

SAFETY PRECAUTIONS

Please take note of the safety instructions to prevent any potential accident or misuse

of the projector.

Child injuries can be prevented by following these simple safety precautions.

The precautions should be followed in the same manner when you store or move your

existing projector.

• Safety precautions are given in two forms, i.e., WARNING and CAUTION as

detailed below.

WARNING: Failure to follow the instructions may cause serious injury and

even death.

CAUTION: Failure to follow the instructions may cause personal injury or

product damage.

• Read the owner’s manual carefully and keep it on hand.

WARNING/CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning ﬂash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated dangerous

voltage within the product’s enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the device.

WARNING/CAUTION

— TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

Read these instructions. Keep these instructions.

Heed all warnings. Follow all instructions.

Indoor Installation

WARNING

Do not install products including projectors and remote controls in the

following places:

— Any place exposed to direct sunlight;

— Any humid place such as bathroom;

— Any place near hot objects such as ﬂammables and stoves;

— Any place where oil, oil mist, and steam can reach such as a worktop or places

near a humidiﬁer;

— Any place where water can splash like a vase or the aquarium;

— Any place that is dusty or exposed to wind and rain;

— Any place that is under the air conditioner or is directly exposed to the wind

from the air conditioner;

— Any place near ﬂammable materials such as ﬂammable sprays, etc.; or

— Any cupboard, bookcase shelf or cabinet without a ﬁxture installed and any

place where a pet can access.

• It may cause an electric shock, fire, malfunction, deformation or falling.

Be careful not to drop the projector when connecting an external device.

• It may cause injury or damage to the product.

Keep the following precautions in mind to prevent the temperature rise inside

the projector:

— Install the air vents at least 30 cm away from the wall.

— Do not install the product in a place where it cannot be ventilated, such as on a

bookcase or in a closet.

— Do not install the product on carpet or cushion.

— Make sure that the air vents are not blocked with tablecloths, curtains, etc.

• It may cause a fire.

For places where oil or oil mist can reach, do not install the product on a wall

or ceiling.

• The product may be damaged and fall.

Do not allow a child to hang or climb on the installed projector.

• The projector may fall and cause injury or death.

CAUTION

When moving the projector, be sure to turn off the power switch and

disconnect the power plug, antenna cable and the connection cord between

the devices.

• A failure to do so may cause damage to the projector or the cord, resulting in a

fire or electric shock.

Do not install the projector on a shaky shelf, a slanted place, a place subject

to vibrations, a place where the projector is not fully supported or on a fabric

such as tablecloths.

• It may cause injury as the projector falls or tips over, or it may cause a

malfunction of the projector.

To prevent damage to the power cord or plug, do not install the projector

where the cord can be walked on.

• It may cause a fire or electric shock.

When installing the projector, do not install it too close to the wall.

• The cable connection may be deteriorated or the projector and its cables may be

damaged.

When installing the projector on a cabinet or a shelf, make sure that the front

end of the bottom of the projector does not come out.

• The projector may fall due to the unbalance of the center of gravity and cause

injury to people or a malfunction.

When in Use

WARNING

When thunder or lightning strikes, unplug the power cord and do not touch

the antenna wire.

• It may cause an electric shock.

If there is a gas leak from the gas lines, do not touch the outlet and be sure to

vent by opening the window.

• Sparks may be caused and lead to a fire or burns.

When using the product with an external device connected such as a games

console, make sure the connection cable is long enough.

• The product may fall over and cause injury or product damage.

Do not scratch or give an impact on the projector with metallic materials or

objects.

• It may cause injury to people or damage to the product.

Do not insert metallic objects including coins, hairpins or a piece of iron or

ﬂammable objects such as paper or matches into the projector.

• It may cause a fire or electric shock.

When replacing the batteries used for the remote control, be careful not to let

children eat them and keep the batteries out of reach of children.

• If a child swallows the battery, consult a doctor immediately.

Keep the plastic wrapping of the product out of the reach of children.

• If a child misuses it, it may suffocate the child.

Do not touch near the vents during the operation or immediately after the

power is turned off as they generate intense heat.

• The heat does not indicate a defect or a problem of the projector when it is

operating so use it with confidence.

Do not look into the front of the lens when the projector is operating. Strong

light is projected from the product which can cause injury to your eyes.

Never try to disassemble or modify the projector yourself. Always seek a

qualiﬁed service technician or consult your dealer or local Service Center for

inspection, adjustment or repairs.

• It may cause a fire or electric shock.

CAUTION

Do not use any product that uses high voltage electricity near the projector.

(e.g. An electric ﬂy swatter)

• It may cause a malfunction.

Do not place any liquid containers such as a vase, pot, cup, cosmetics or

medicine, decorations such as candles or any heavy objects on top of the

projector.

• Doing so may cause a fire, electric shock and injury due to failing.

The surface of the AC adapter is hot, so be careful not to put the surface

against your skin or let the children touch the surface during use. (Except for

the models that do not use an adapter)

Do not hold or move the projector upside down by grabbing only the power

cord, signal cable, or projection mirror.

• Doing so may damage the product or cause an electric shock or fire.

Even if the projector is turned off with the remote control or the button, the

power is not completely cut off if the power cord is plugged in.

If you use headphones or earphones, do not use them at high volume or for a

long period of time. (It applies only to the models that support headphones

(earphones).)

• Doing so may damage your hearing.

Do not start the projector when the volume is high.

• A loud volume can cause hearing loss.

Do not use or store the projector outdoors for an extended period of time.

Do not touch the projector’s lens or give an impact on it.

• It may cause damage to the product.

Do not block the light from the projector lens with a person, book or other

objects.

• If the light from the projector shines on an object for a long time, it can cause

fire due to the heat of such light. Also, the reflected light can heat the lens and

cause damage to the projector.

Do not mix old and new batteries together.

• It may cause battery rupture or fire due to liquid leakage or may cause electrical

shock.

When replacing the batteries, make sure that they are properly installed

according to the polarities (+, -).

• Battery rupture or leakage may lead to fire, explosion, injury or contamination

(damage) of the surrounding area.

Do not expose the batteries to direct sunlight, ﬁreplace, electric heater, high

temperature above 60 °C, excessively humid places or excessive heat.

• It can cause an explosion or fire.

Do not throw or disassemble the battery.

• It can cause a fire and explosion due to battery damage.

Do not carelessly throw away old batteries.

• It can cause an explosion or fire. The disposal method may vary by country and

region. Dispose of it in an appropriate manner.

Risk of ﬁre or explosion if the battery is replaced by an incorrect type.

Supervise children and to never allow them to stare into the projector beam at

any distance from the projector.

Use caution when using the remote control for staring the projector while in

front of the projection lens.

The user to avoid the use of optical aids such as binoculars or telescopes inside

the beam.

Power

WARNING

Make sure the power plug is securely plugged in to prevent it from shaking.

• If the connection is unstable, it may cause a fire.

Do not plug too many devices into one multi-power outlet.

• This may result in fire due to the power outlet overheating.

Do not insert a metal object such as chopsticks into the other end of the

power plug while it is plugged into a wall outlet. Also, do not touch the power

plug immediately after unplugging it from the outlet.

• It can cause an electric shock.

Connect the power plug to a grounded outlet or multi-tap. (Except for any

device without ground connection)

• A failure to do so may cause an electric shock due to a malfunction or electrical

short.

Never touch the power plug with wet hands.

• It may cause an electric shock.

Disconnect the power plug from the outlet when you are not using the

projector for a long time or absent.

• Dust collects and may cause an electric shock and fire caused by a short circuit

due to heat, ignition and insulation/degradation.

The Power Plug is the disconnecting device. In case of an emergency, the

Power Plug must remain readily accessible.

If any of the following occurs, it could be a malfunction of the product, so

you must immediately turn the projector off, unplug the power cord from the

outlet, and contact the service center:

— When the product is damaged;

— When the product fails;

— When there is a foreign substance inside the product; or

— When the product smokes or smells.

• It may cause a fire or electric shock.

CAUTION

Do not unplug or plug the power plug from/in the outlet while the power

switch is on. (Do not use the power plug as a switch.)

• It may cause a fire or malfunction.

When removing the AC adapter or power cord, be sure to hold the plug part.

• A failure to do so may cause a fire or damage to the product.

Do not damage the AC adapter, power cord or power plug, place heavy objects

on them or give an impact on them.

• It may cause a fire, electric shock or damage to the product.

Attach the power cord and AC adapter connected to the projector in a way

that they are fully seated.

• Poor contact can cause a malfunction of the product and fire.

If there is dust on the pin part of the power plug or the outlet, clean it

thoroughly.

• It may cause a fire.

Keep the power cord away from heat sources.

• The coating of the cord may melt and cause a fire or electric shock.

Use only the authorized power cord or AC adapter supplied by LG Electronics.

Do not use any other products.

• It may cause a malfunction of the product, fire or electric shock.

Cleaning

WARNING

Do not spray water directly onto the projector when cleaning it.

• It may cause a fire or electric shock.

CAUTION

How to clean the projector

— Disconnect the plug from the outlet before cleaning.

— Do not wipe the optical system (the lens and mirror) immediately after the

power is turned off.

— Do not spray the water with a sprayer on the product or wipe the product with

a damp cloth.

— Wipe the product gently with a soft cloth.

— Do not use any detergents, automotive or industrial polishes, abrasives, waxes,

benzenes or alcohols.

• It may cause a fire, electric shock or damage to the projector (deformation,

corrosion, and breakage).

How to clean the lens

— Clean the lens if any dust or smudge appears on the surface of the lens.

— Clean the surface of the lens with an air sprayer or a soft, dry cloth.

— To remove dust or stains on the lens, use a compressed air duster, cotton swab,

or soft cloth to gently wipe the lens.

— Never clean the lens when the projector is operating or immediately after the

projector is turned off.

— Do not use any detergents, automotive or industrial polishes, abrasives, waxes,

benzenes, alcohols, water, etc. on the lens, as they will damage the projector.

Consult your dealer or the service center for cleaning the interior of the

product once a year.

• If you do not clean the interior of the projector for a long time while dust

collects, it may cause a fire or malfunction.

CHECKING BEFORE REPORTING

MALFUNCTION

Please check the list below when you experience the following symptoms during use of

the product. It may not be a failure.

Projector Safety Check

Symptoms

• The projector does not display anything on the screen or output sound when

it is turned on.

• The product emits smoke or a burning smell.

• Water or foreign substances are present inside the product.

• Part of the projected image is cut out.

• A strange noise (crackling or sparking sound) regularly occurs from inside the

projector.

• The projector still displays the screen or outputs sound when it is turned off.

• There are other errors or failures.

Causes and Solutions

• For safety, turn off the power switch and remove the plug from the socket.

• Contact the place of purchase or authorized service center for product

inspection.

• Do not attempt to repair the product yourself.

Troubleshooting

Symptoms

Causes and Solutions

I cannot turn on

the Projector.

• Please make sure your projector power plug is correctly

connected to the outlet.

• There may be a problem with the outlet, so try plugging

the power cord of another product into the outlet

where the projector was plugged in.

Cannot control

the Projector

with the remote

control.

• The remote control may not work properly where a

lamp with electronic stabilizer or a three-wavelength

lamp is installed.

— In this case, replace the lamp with electronic

stabilizer or the three-wavelength lamp with

international standard products to ensure the

remote control works properly.

• Check if there is any obstacle between the product and

the remote control.

• When replacing the batteries, make sure that they are

properly installed according to the polarities (+, -).

• Replace both used batteries with new ones.

The power turns

off suddenly.

• Check whether the [Sleep Timer], [Auto Off], or [Auto

Power Off] is set.

• See if the external devices are operating together.

• The auto-off function may have been activated. This

product is equipped with an auto-off function that

automatically turns the product off when no signal

is present or when the remote control has not been

pressed, depending on the settings for the auto-off

function.

Symptoms

Causes and Solutions

I see dots on the

screen.

• There is a colored dot (bright dots, dark dots, stationary

dots, and/or flickering dots) on the screen.

— This projector was produced with high precision

technology. However, a tiny dark or bright dot may

appear on the screen. This is a common occurrence

due to the production process, and it does not

indicate a functional failure.

※ Bright spot: brightly lit dots, Dark spot: invisible or blurred

point of text or objects, Blinking: ﬂashing dots, Bright dot:

glowing dots that are brighter than regular images

I hear a noise.

•

Electrical noise: this is a small sound generated from

the operation of the high-speed switching circuit that

supplies current to the projector, and the noise may

vary depending on the product. This noise is normal and

does not affect the projector’s functions. LG Electronics

manages the manufacturing of projectors according to

strict standards. A fixed level of noise does not indicate

a problem. Please understand that this does not allow

you to get an exchange or refund.

•

Fan sound: to maintain the temperature inside the

projector at an appropriate level, the fan sound may

increase or decrease depending on the ambient

temperature.

CHECKING INFORMATION

Speciﬁcations

PF610P (PF610P-SA)

MODEL

PF610P (PF610P-CB)

1920 (Horizontal) × 1080 (Vertical)¹⁾

16:9 (Horizontal:Vertical)

Resolution (Pixel)

Aspect ratio

Working range of

the remote control

6 m (Max.)

Projection distance 1588 mm to 3176 mm

— Screen size

— 1524 mm to 3048 mm (60 inches to 120 inches)

Ratio of upward

projection

100 %

Power consumption 98 W

Manufacturer: Honor

Model: ADS-110CL-19-3 190110G

Input: 100-240 V~ 50/60 Hz 1.5 A

AC-DC Adaptor

Output: 19.0 V

5.79 A

Audio Output

Height

3 W + 3 W

69 mm (without foot), 73.5 mm (with foot)

Width

225.0 mm

Depth

192.0 mm

Weight

1.65 kg

USB Device

5 V, 0.5 A (Max.)

Temperature

Operation

Storage

0 °C to 40 °C

-20 °C to 60 °C

Environment

Condition

Relative Humidity

Operation

Storage

0 % to 80 %

0 % to 85 %

• Use only power supplies listed in the user instructions.

• Contents in this manual may be changed without prior notice due to upgrade of

product functions.

1) Full HD resolution with 2.1 million discrete pixels projected by XPR (Expanded Pixel

Resolution) video processing.

HDMI Supported mode

HDMI (DTV)

Resolution

Horizontal Frequency (kHz) Vertical Frequency (Hz)

640 x 480

31.46

31.5

59.94

720 x 480

31.47

31.5

59.94

720 x 480

720 x 576

31.25

44.96

1280 x 720

1920 x 1080

59.94

37.5

28.12

33.72

33.75

26.97

59.94

23.97

33.71

33.75

56.25

67.43

67.5

29.97

59.94

HDMI (PC)

Resolution

Horizontal Frequency (kHz) Vertical Frequency (Hz)

640 x 350

720 x 400

31.46

37.87

48.36

47.71

54.34

63.98

67.5

70.09

70.08

59.94

60.31

640 x 480

800 x 600

1024 x 768

1360 x 768

1152 x 864

1280 x 1024

1920 x 1080

60.01

60.05

60.02

• If an invalid signal is input into the projector, it will not be displayed properly on

the screen or a message such as [No Signal] or [Invalid Format] will be displayed.

• The projector supports the DDC1/2B type as the Plug and Play function (Auto-

recognition of PC monitor).

• 1920 x 1080 is recommended as the best picture quality in the PC mode.

Licenses

Supported licenses may differ by model. For more information about licenses, visit

www.lg.com.

The terms HDMI, HDMI High-Deﬁnition

Multimedia Interface, and the HDMI Logo

are trademarks or registered trademarks of

HDMI Licensing Administrator, Inc.

Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio,

Dolby Atmos, and the double-D symbol are trademarks of Dolby Laboratories.

Open Source Software Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that

is contained in this product, please visit https://opensource.lge.com.

In addition to the source code, all referred license terms, warranty disclaimers and

LG Electronics will also provide open source code to you on CD-ROM for a charge

covering the cost of performing such distribution (such as the cost of media, shipping,

and handling) upon email request to [email protected].

This offer is valid for a period of three years after our last shipment of this product. This

offer is valid to anyone in receipt of this information.

Other speciﬁcations

As with any bright light source, do not stare into the beam, RG2 IEC 62471-

5:2015.

Risk Group 2

CAUTION Possibly hazardous optical radiation

emitted from this product. Do not stare at

operating lamp. May be harmful to the eye.

This label is attached to the bottom of the product and language may differ.

Symbols

Refers to alternating current (AC).

Refers to direct current (DC).

Refers to class II equipment.

Refers to stand-by.

Refers to “ON” (power).

Refers to dangerous voltage.

ABOUT LG PROJECTOR

Image shown may differ from your projector.

Your projector’s OSD (On Screen Display) may differ slightly from that shown in this

manual.

[ ] : the buttons and the text to be displayed on the projector screen.

P/NO : SAC38518908 (2109-REV00)

CONTENTS

ABOUT LG PROJECTOR

HOW TO OPERATE THE PROJECTOR

HOW TO USE VARIETY OF CONTENTS

CONNECT OTHER DEVICES

ENJOYING INTERNET

TOUR LIST OF SETTINGS

TROUBLESHOOTING

ABOUT LG PROJECTOR

Home Tutorial

Using the Home feature of the LG Projector

You can open the Home screen by pressing the

You can combine frequently used apps on a single screen and use whichever you want

at any time.

button on your remote control.

Launch [Search].

Move to the [Home Dashboard].

You can select or control a device (mobile, external device, etc.) connected

to the projector.

Move to the recently used app.

Long-press the

button on the remote control or focus the [Recents].

You can run or close a recently used app in the list provided in the preview

area at the top.

You can run, move, and delete the apps installed on your projector.

Focus on each App area. It provides the preview at the top.

You can check or run useful features of each app and recommended

content on the preview without entering into the app.

• Some apps may not provide the preview.

• The availability of and access to contents and services in LGE device are subject

to change at any time without prior notice.

Manage LG Projector Home

You can view a list of all apps installed on your projector, or change their positions.

1 Select the app you want to edit, and press and hold the

Wheel (OK) or

(OK) button on the Remote Control. This will activate the app edit mode.

Or you can select the edit button at the far right corner of the Home list to

enter the app edit mode.

2 To move the app to your desired position, go to the position and press the

Wheel (OK) or

(OK) button.

• You can move as many apps as you wish before exiting the edit mode.

• You can also move apps with the buttons on your remote control.

3 After the editing is done, press the at the top right to exit the app edit

mode.

• The default projector app cannot be deleted.

You can automatically arrange the app list in the order of most frequently

used based on your accumulated app usage pattern.

You can add your favorite video service channel to the list.

• This feature is available only when the network is connected.

• Some models may not be supported.

Network Setting

If you conﬁgure settings for the network, you can use various services such as online

contents and applications.

Setting a Wired Network

1 Connect the LAN port of the projector and the router using a LAN cable.

The router should be connected to the Internet beforehand.

2 Press the

(Q. Settings) button on the remote control and select

[Connection] [Network Connection Settings] [Wired Connection

(Ethernet)].

• If the router supports DHCP, the projector is automatically connected to the

network when you connect the projector to the network with a LAN cable.

Setting a Wireless Network

1 Turn on the power of the router connected to the Internet.

2 Press the

(Q. Settings) button on the remote control and select

[Connection] [Network Connection Settings] [Wi-Fi Connection].

3 When the network search is complete, the list of networks available for

connection is shown.

4 Select a network to connect.

If your Wireless Router is password protected, enter the password conﬁgured

for the router.

Cautions for Network Setup

• Use standard LAN cable (connect to Cat7 or higher with RJ45 connector, 10

Base-T, or 100 Base TX LAN port).

• Resetting the modem may fix some network connection problems. Turn the

power OFF, disconnect and reconnect it, and then turn the power on to solve the

problem.

• LG Electronics is not responsible for any network connection problems or any

faults, malfunctions, or errors caused by network connection.

• The network connection may not work properly because of network settings or

the Internet service provider.

• DSL service must use a DSL modem; and cable service must use a cable modem.

Since only a limited number of network connections may be available, projector

network setting may not be used depending on the contract with Internet

service provider. (If the contract does not allow more than one device per line,

only the already-connected PC may be used.)

• A wireless network can experience interference from other devices that use

the 2.4 GHz frequency (wireless phone, Bluetooth device, or microwave oven).

Although interference can also happen when using the 5 GHz frequency, it is less

likely to occur.

• The wireless environment can make wireless network service run slowly.

• Failure to turn off all local home networks may cause excessive traffic on some

devices.

• The access point device must support wireless connections and wireless

connection feature must be enabled on the device to have AP (access point)

connection. Contact the service provider for availability of wireless connections

on the access point.

• Check SSID and security settings of the AP. Refer to the appropriate

documentation for SSID and security settings of the AP.

• Invalid settings of network devices (wired/wireless line sharer, hub) can cause the

projector to operate slowly or not operate properly. Install the devices correctly

according to the appropriate manual and network.

• The connection method may differ depending on the AP manufacturer.

HOW TO OPERATE THE PROJECTOR

To View More Features of the Remote Control

You can control more features or external devices connected to your projector by using

the buttons displayed on your projector screen.

1 Press the button on the remote control.

2 Using the remote control, select your desired button on [More Actions]

displayed on your projector screen.

You can set up the universal remote control.

• You need Magic Lighting Remote to use universal remote control

function. (The provided remote control differ depending upon model.)

External input information is displayed on the screen.

When the projector malfunctions, you can get help to solve the problem.

• The types of buttons appearing on the [More Actions] vary, depending on the

region and the type of connected device.

• The configurable items differ depending upon model.

Universal Remote Control

Automatically Setting the Universal Remote Control

When you set up the universal remote control, you can control the peripherals (Blu-ray

/ DVD player, home theater, set-top box, etc.) with the Magic Lighting Remote rather

than using their dedicated remote controls.

Connect the devices to be set to the projector’s HDMI input, and turn the power of the

device on.

The projector will scan the connected device to automatically set the universal remote

control without manual setting.

• After setting the universal remote control, you may need to do some additional

user settings.

• It may take several seconds to complete the settings for the universal remote

control.

• In some models, you can set the universal remote control only after converting

to an input of a connected device.

• Depending on the connected device, the automatic setting feature for universal

remote control (automatic device connection) may not be supported.

Manually Setting the Universal Remote Control

If the universal remote control is not automatically set or it is connected to the AV

input/Component input, you can manually set it.

1 Select the

(Q. Settings)

Settings] [Universal Control Settings].

[Connection] [Device Connection

2 Select the type of the device you want to set.

3 Complete the settings for the universal remote control according to the

guidance on the screen.

You can change or cancel the universal remote control settings.

• This feature can only be used with the Magic Lighting Remote. (The provided

remote control differ depending upon model.)

• Some models may not be supported.

• AV input/Component input ports are available in certain models only.

• When changing the settings, check that the device to be changed is turned on.

• You can set up the universal remote control with the latest updated information.

• The manual setting feature for universal remote control is not supported for a

game console.

• Some buttons may not work depending upon the model of the external device.

• Point the Magic Lighting Remote at the device you want to control. Make sure

that there are no objects in front of the device to ensure that the remote control

signal is well received.

Launching Apps through [Quick Access]

Using apps quickly and easily with [Quick Access]

Press and hold a number button on the remote control to open an app or to activate an

external input registered to the button.

Setting the [Quick Access]

1 Launch the app or input you wish to assign.

2 Press and hold the number button (1~8) you want to register.

No. 9 is ﬁxed to [Quick Help].

3 When the registration pop-up window appears, select [Yes].

• If you press and hold a number button that has already been registered, the

registered function will be performed.

• To see the items that can be registered, select a number that has not been

registered in the [Edit Quick Access] mode.

• If you are in a mode where [Quick Access] cannot run, no action will be

performed.

• If you delete a registered app, [Quick Access] will be deregistered as well.

Checking and editing [Quick Access]

Press and hold the number 0 button on the remote control.

The [Quick Access] edit screen appears.

Selecting a number that has already been registered allows deregistering

it.

When you select a number that has not been registered, items that can

be registered will be shown.

An item that has been registered to a different number is indicated with

a check mark.

You can view a brief instruction for this function.

Using SIMPLINK

You can conveniently control and use various multimedia devices connected through

HDMI with the projector’s remote control.

1 Connect the SIMPLINK HDMI Output port to the projector’s HDMI IN port with

an HDMI^®cable.

2 Press the

(Q. Settings) button on the remote control and select

[Connection] [Device Connection Settings].

3 Set [SIMPLINK (HDMI-CEC)] to [On].

4 Conﬁgure the [Auto Power Sync] settings to [On] or [Off]. (If [Auto Power

Sync] is set to [On], turning on a SIMPLINK-linked device will turn the

projector on. When you turn off the projector, the device will also be turned

off.)

5 Turn on the connected device. When the projector automatically connects to

the device, the input will switch. If the device is not automatically connected to

the projector, click the

button.

• This feature works only with devices with the

logo. Check for the

SIMPLINK logo on the external device. There may be a problem using the device

if the device does not meet the required specifications.

• A high-speed HDMI^®cable with CEC (Consumer Electronics Control) function is

required to use SIMPLINK. Pin 13 of the high-speed HDMI^®cable is used for data

transfer between devices.

• If you want to output sound to the external audio equipment connected through

the HDMI^®cable, set [SIMPLINK (HDMI-CEC)] to [On].

Supported SIMPLINK Functions

•

Instant Play

When you start a multimedia device, you can immediately watch content from

the device on the projector without having to control anything.

Controlling devices with the projector remote control

Enables the user to control multimedia devices with the projector remote control

to watch content.

– The pointer function of the Magic Lighting Remote can be limited.

•

Main Power Off

If [Auto Power Sync] is set to [On] in the [Device Connection Settings] settings

and the projector is turned off, the devices connected to your projector via

SIMPLINK will also be turned off.

– This feature is only available in certain devices.

Main Power On

If [Auto Power Sync] is set to [On] in the [Device Connection Settings] settings,

turning on a SIMPLINK-linked device will turn the projector on.

– If [SIMPLINK (HDMI-CEC)] is set to [Off], [Auto Power Sync] cannot be set

to [On].

– Some models may not be supported.

Connecting an Input Device to USB

Using a USB Wired/Wireless Mouse

Connect your mouse to the USB port. Use the mouse to move the pointer on the

projector screen and select the menu you want.

• The right button and the special buttons on the mouse do not work.

• When using a wireless USB mouse/keyboard, the experience may be affected by

the distance and wireless condition.

Using a USB Wired/Wireless Keyboard

Connect your keyboard to the USB port. You can enter text with the connected

keyboard device.

• It is not possible to enter text on some screens.

• It is recommended that you use a product that has been tested for compatibility

with LG projectors.

LOGITECH K360, LOGITECH K400, LOGITECH K570, LG Electronics MKS-1200

• You can change the input language by pressing the language switch key or the

right Alt key. It can also be changed by pressing the Ctrl key and the Space key

at same time.

• Wireless USB keyboard use may be affected by the usage range and the wireless

environment.

• To enter text in the text field, use the on-screen keyboard on your projector

screen or a USB keyboard.

Using a Gamepad

Connect your gamepad to the USB port on the projector if the game requires a

gamepad.

• It is recommended that you use a gamepad that has been tested for

compatibility with LG projectors. LOGITECH F310, LOGITECH F510, LOGITECH

F710, LOGITECH Rumblepad 2, LOGITECH Cordless Rumblepad 2, LOGITECH

Dual Action Gamepad, MICROSOFT Xbox 360 Controller (cable), SONY

Playstation(R)3 Controller

HOW TO USE VARIETY OF CONTENTS

Using [LG Content Store]

You can quickly and conveniently browse for TV Shows, Movies, and more to watch

immediately. You can also download and use apps from various categories such as

education, entertainment, lifestyle, news, and games.

1 Press the

button on the remote control.

2 Launch the [LG Content Store] application.

• Depending on the model, the provided contents may differ or some features may

be limited.

• Exercise caution when in used by children. Children may have access to

inappropriate online content through this product. You can block inappropriate

online content by restricting access to some apps.

– Conﬁgure the settings in

(Q. Settings)

[General] [Safety]

[Application Locks].

Recommended Content on the Main Screen

You can view recommendations for the most popular content and apps in each

category on the [LG Content Store] main screen. Choose a piece of content to watch it,

or choose an app to download it.

• Some models may not be supported.

• This feature is available only when the network is connected.

Installing Apps

You can install various apps on your projector from the [LG Content Store].

1 Press the

button on the remote control.

2 Launch the [LG Content Store] application.

3 Select the [All Apps] category shown at the top of the screen. The list of

available apps in the selected category will be shown.

4 Select an app to set up from the list.

5 Read the details of the app and then press [Install].

6 When the installation is complete, you can run the app immediately.

• Available categories may vary depending on the country or service status.

• If the storage on your projector is insufficient, you can install the apps by

connecting an external memory device.

• Some USB storage devices may not be supported or may not work properly.

• USB drivers containing apps from other LG TVs or LG Projectors may not be

used.

• You can delete apps you have downloaded in the [My Apps].

Managing your LG Account

In [Account Management], you can use your email address to create a new LG account.

Content Recommendation

If you are watching the projector using a set-top box, you must complete the setup of

the universal remote control to use the recommendation feature normally.

1 Press the

button on the remote control.

2 Launch

• Some models may not be supported.

• You must connect to the network to use the recommendation feature.

• The supported services vary depending on countries, so the recommendations

may be provided differently.

• The list of the recommendations may be less relevant or irrelevant, depending on

the information of the program you are watching.

Search Content

You can receive recommendations for content based on viewing patterns or search by

yourself for the content you want.

1 Press the

2 Launch

button on the remote control.

3 Search for a variety of content and information by typing in your desired

search terms.

Returns to the previous screen.

Provides a list of content for the selected genre.

Enter your desired search term.

Exit the search.

• You must connect to the network to use the search feature.

• Search results may vary depending on the region, network settings, and whether

you have agreed to the terms and conditions.

CONNECT OTHER DEVICES

Using [Home Dashboard]

You can select or control a device (mobile, external device, etc.) connected to the

projector.

• Press the

button on the remote control and select [Home Dashboard].

5 6 7

You can play sound from a smart device connected via Bluetooth.

You can check and select the external device connected through the

external input port or network.

The currently selected output speaker is displayed, and you can navigate to

the output speaker settings screen.

You can view and select the connected storage device.

[Edit]: You can edit the name of the device connected to [Inputs] or

conﬁgure the related settings.

It refreshes the device list.

Exit the [Home Dashboard].

• The configurable items differ depending upon model.

Share Smartphone Screen

To see the Mobile Device's screen on the projector

1 Enable Screen Share mode on the mobile device.

2 Your projector will be displayed in the list of available devices.

3 Select your projector and request connection.

4 Select accept in the connection request popup window.

5 After the connection is established, the projector will display the screen of the

connected device.

• For a reliable connection always keep the connected device to your projector

updated to the latest OS version.

• A non-LGE device might not connect even when it is detected.

• Connect the device to a 5 GHz router because the performance may be affected

by your wireless environment.

• The response rate may vary, depending upon the user’s environment.

• It differs among devices. For more information on the device you want to

connect to, refer to its user guide.

• If connection fails repeatedly, turn off the projector and the device you want to

connect to, then turn them back on and try again.

Playing Sound from a Smart Device through the

projector’s Speakers

Connect a smart device to the projector via Bluetooth to play sound from the smart

device through the projector’s speakers.

1 Turn the smart device’s Bluetooth on, then select the projector from the list

of devices.

2 The projector will be connected to the smart device.

• If the output speaker is set to [Bluetooth] or has a setup history, the projector

may not be detected in the list of smart devices.

• If the output speaker is set to [Bluetooth], press the

button on the remote

control to open [Home Dashboard], and then select [Sound Share] in the mobile

area to connect.

Connecting USB

Connect a USB storage device (USB HDD, USB Flash Drive) to the USB port on the

projector to enjoy the content ﬁles stored on the USB storage device on your projector.

USB Flash Drive

Tips for Using a USB storage device

• A USB storage device that has a built-in automatic recognition program or uses

its own driver might not be recognizable.

• Some USB storage devices may not be supported or may not work properly.

• If you use a USB extension cable, the USB storage device may not be recognized

or may not work properly.

• Please use only USB storage devices formatted with the FAT32 or NTFS file

system provided by Windows OS.

• It is recommended that you use an external USB HDD with a rated voltage of

5 V or less and a rated current of 500 mA or less. If you use a device requiring

a higher voltage/current than the rated voltage/current, it may not operate

properly due to lack of current.

• For USB hubs and USB storage devices, it is recommended to use a type that

supplies power by connecting the AC adapter to a power outlet.

• It is recommended that you use a USB stick of 32 GB or less or a USB HDD of 2

TB or less.

• If a USB HDD with power-saving function does not work, turn the hard drive off

and on again to make it work properly. See the owner’s manual for the USB HDD

for more information.

• Data on a USB storage device may be damaged, so it is recommended that you

back up any important files. Users are responsible for data management. The

manufacturer bears no responsibility.

• Press the

button on the remote control. To remove the USB storage device,

press the [Eject] button, which appears at the top when you focus on the USB

storage device you want to remove.

If you disconnect the USB storage device without selecting [Eject], an error may

occur in your projector or storage device.

• When you connect a USB storage device of a file system not supported by

the projector to the USB input port, the format message appears. To use the

connected USB storage device, you should format the device first. After format,

all the data of USB storage device will be deleted and formatted as NTFS or

FAT32 file system.

• Press the

button on your remote control. Select the connected USB from

[Home Dashboard] [Storage] and select the [Format] button to format the

USB storage device.

• When connecting a USB storage device, a random file/folder can be created to

provide Smart projector services such as the saving and retrieving of thumbnail

images.

[Photo & Video]

Viewing Photos and Videos

You can view photos and videos using the [Photo & Video] app.

1 Press the

button on the remote control.

2 Launch the [Photo & Video] application.

3 Select your desired storage device.

4 Select and view your desired photo or video.

1 2 3 4

Select your desired type of content and viewing method.

Select and delete your desired content.

(You cannot delete ﬁles that are shared from other devices.)

Select the content you want to play. You can only select the same type of

content as you ﬁrst selected.

Launch [Search].

• Certain content may not be displayed on the list if the number of all content

exceeds 40,000.

Photo Player

Selecting a photo in the [Photo & Video] app runs the photo player. You can view your

saved photos.

Returns to the entire content list.

You can play background music by running the music player.

You can zoom the photos in/out.

Starts the slide show.

Rotates photos.

You can set the size of a photo or change the speed and effect of a slide

show.

Supported Photo Files

File type

Format

Resolution

Minimum: 64 x 64

Maximum

Normal Type: 15360 (W) x 8640 (H)

Progressive Type: 1920 (W) x 1440 (H)

jpeg, jpg, jpe

JPEG

Minimum: 64 x 64

Maximum: 5760 (W) x 5760 (H)

png

PNG

BMP

Minimum: 64 x 64

Maximum: 1920 (W) x 1080 (H)

bmp

Video Player

Selecting a video in the [Photo & Video] app runs the video player. You can view your

saved videos.

Returns to the entire content list.

You can select other content by displaying the playlist while watching a

video.

You can control basic video playback functions.

You can do the settings related to play on repeat of the video.

You can set additional options.

Setting Additional Options

You can change subtitle settings.

You can set audio tracks.

You can set continue watching to resume playing from the last viewed

scene.

Returns to the basic operation screen.

Supported Video Files

Maximum data transfer rate

• Full HD video

H.264 1920 x 1080@60P BP/MP/[email protected] Maximum 40 Mbps

HEVC 1920 x 1080@60P Main/[email protected] Maximum 40 Mbps

Supported external subtitles

*smi, *srt, *sub (MicroDVD, SubViewer 1.0/2.0), *ass, *ssa, *txt (TMPlayer), *psb

(PowerDivX), *dcs (DLP Cinema)

Supported embedded subtitles format

• Matroska (mkv): Sub Station Alpha (SSA), Advanced Sub Station Alpha (ASS),

SRT

• MP4 (mp4): Timed Text

Supported video codecs

Extension

Codec

Video

VC-1 Advanced Proﬁle (except for WMVA), VC-1

Simple and Main Proﬁles

asf

wmv

WMA Standard (except for WMA v1/ WMA

Speech)

Audio

Video

Xvid (except for 3 warp-point GMC), H.264/AVC,

Motion Jpeg, MPEG-4

avi

MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby

Digital, LPCM, ADPCM

Audio

Video

Audio

H.264/AVC, MPEG-4, HEVC, AV1

mp4

m4v

mov

Dolby Digital, Dolby Digital Plus, AAC, MPEG-1

Layer III (MP3), Dolby AC-4, MPEG-H 3D Audio

Video

Audio

H.264/AVC, MPEG-4

3gp

3g2

AAC, AMR-NB, AMR-WB

MPEG-2, MPEG-4, H.264/AVC, VP8, VP9, HEVC,

AV1

Video

mkv

Dolby Digital, Dolby Digital Plus, AAC, PCM, MPEG-1

Layer I, II, MPEG-1 Layer III (MP3)

Audio

Video

H.264/AVC, MPEG-2, HEVC

trp

mts

MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby

Digital, Dolby Digital Plus, AAC, PCM, Dolby AC-4

Audio

Video

Audio

MPEG-1, MPEG-2

mpg

mpeg

dat

MPEG-1 Layer I, II, MPEG-1 Layer III (MP3)

Video

Audio

MPEG-1, MPEG-2

vob

Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM

• Dolby AC-4, MPEG-H 3D Audio: Some models may not be supported.

Cautions for Video Playback

• Some user-created subtitles may not work properly.

• A video file and its subtitle file must be located in the same folder. For subtitles

to be displayed properly, make sure that the video file and the subtitle file have

the same name.

• Subtitles on a Network Attached Storage (NAS) device may not be supported

depending on the manufacturer and model.

• Streams that include Global Motion Compensation (GMC) and Quarterpel

Motion Estimation (Qpel) are not supported.

• Only Window Media Audio V7 and later are supported.

• The AAC main profile is not supported.

• Video files created by some encoders may not be played.

• Video files in a different format than specified may not be played properly.

• Video files stored on a USB storage device that does not support High Speed

may not be played properly.

[Music]

Playing Music

You can listen to music by using the [Music] app.

1 Press the

button on the remote control.

2 Launch the [Music] application.

3 Select your desired storage device.

You can select your desired songs from all of your storage devices and add

them to [My Playlist].

4 Select your desired music content and enjoy it.

1 2 3 4 5

Select the desired type of content list.

Select and delete your desired content.

(You cannot delete ﬁles that are shared from other devices.)

Select the content to add to My Playlist.

Open the music player.

Launch [Search].

Using the Music Player

You can conveniently play music by selecting a saved music ﬁle in the [Music] app or

selecting the music player icon while playing content in an app such as [Photo & Video].

1 2 3 4 5 6

You can play music from the selected storage device.

You can set repeat playback and random playback.

The conﬁgurable items differ depending upon model.

: You can turn the screen off while listening to music or display the

music player in full-screen mode.

: You can listen to music with the screen turned off.

You can change the position of the music player.

You can minimize the music player.

This feature closes the music player.

Lyrics are available for music ﬁles that provide them.

In some music ﬁles, you can choose a lyric section and move the playback

position.

• The lyrics feature is only supported on some devices.

• The lyrics may not be displayed in sync depending on the lyrics data

in the music file.

• Reopen your music player by pressing the volume buttons on your remote

control.

• You may not be able to use the music player for some features.

Audio Format

File type

Item

Bit rate

Info

32 kbps ~ 320 kbps

Sample freq.

Support

16 kHz ~ 48 kHz

MPEG-1, MPEG-2

mono, stereo

mp3

wav

Channels

Bit rate

Sample freq.

Support

8 kHz ~ 96 kHz

PCM

Channels

Bit rate

mono, stereo

64 kbps ~ 320 kbps

8 kHz ~ 48 kHz

Vorbis

Sample freq.

Support

ogg

wma

flac

Channels

Bit rate

mono, stereo

128 kbps ~ 320 kbps

8 kHz ~ 48 kHz

WMA

Sample freq.

Support

Channels

Bit rate

up to 6 ch

Sample freq.

Support

8 kHz ~ 96 kHz

FLAC

Channels

mono, stereo

• The number of supported channels may vary depending upon the sample

frequency.

View Computer Files

Connect to a PC Through the Content Sharing Function

Content Share allows you to enjoy videos, music and photos saved on your PC.

Play the content with sharing software on the PC

If you have Windows 7 or later installed on your PC, you can play music, video, photos,

etc. on your projector without needing to install a separate program.

1 Connect you projector and PC to the same network. PCs installed with

Windows 7 or later also need to be connected to a network.

2 Right-click the desired music/video/photo ﬁle you wish to play, then select

your model using the “Play To” feature built into Windows 7 or later to play

the ﬁle.

To play on other devices like your mobile phone, refer to the relevant user

guide.

• Even when multiple projectors or devices are connected, the selected file is

played through only one device. The playback rate may vary depending on the

network connection.

Use the SmartShare PC Software to play the content saved on the PC

You can use SmartShare PC Software to connect the music/videos/photos saved on

the PC to your home network and play them on your projector.

1 Conﬁgure the projector and PC installed with SmartShare on the same

network.

• The SmartShare service is only available when the projector and server PC

are connected to a single router.

2 Download and install SmartShare PC Software from the LG website (www.

lg.com). Before installation, exit all programs running on the PC, such as a

ﬁrewall or an anti-virus software.

3 Run SmartShare PC Software and conﬁgure the share settings.

4 Shared videos and photos are played from the [Photo & Video] app on the

projector. Shared music ﬁles are played from the [Music] app on the projector.

• The server should be running in order to watch the shared file on your projector.

• For information on how to use the SmartShare PC Software, refer to the

software’s help section.

Matters that require special attention during Content Share

• Check your network settings if the Content Share option does not work properly.

• May not work properly on a wireless network. It is recommended that you

connect to a wired network.

• If multiple display devices are connected to one device, the content may not be

played properly depending on server performance.

• May not work properly depending on the network environment.

• To watch the 1080p video through Content Share function, a router that uses

5 GHz frequency is required. If a 2.4 GHz router is used, the video may not play

properly.

• The Content Share function may not be supported for a router that does not

support multi-cast. For more information, refer to the user guide that came with

your router or contact the manufacturer.

• Captions are only supported on some connected devices.

• SmartShare PC Software is recommended for reading captions.

• When a subtitle file is added later, disable the shared folder and then enable it

again.

• The DRM files in the connected device will not play.

• Even for the file format supported by the projector, the supported file format

may differ depending on the connected device environment.

• If there are too many folders or files in a folder, it may not work properly.

• The information on the file imported from the connected device may not be

displayed correctly.

• Depending upon the encoding, some streams may not play in Content Sharing

mode.

Share Computer Screen

To see the PC screen on the projector

Connect wireless

1 Enable Screen Share mode on the PC. Your projector will be displayed in the

list of available devices.

2 Select your projector and request connection.

3 After the connection is established, the projector will display the screen of the

connected device.

• For a reliable connection always keep the connected device to your projector

updated to the latest OS version.

• It is recommended that you use this function at close range.

• Though it can be connected without a wireless router, connecting your device to

a 5 GHz router is recommended because the performance can be affected by

the surrounding wireless environment.

• The response rate may vary, depending upon the user’s environment.

• It’s different from Windows version. For more information on the device you

want to connect to, refer to its user guide.

• If connection fails repeatedly, turn off the projector and the device you want to

connect to, then turn them back on and try again.

Connect wired

Connect the PC with projector by HDMI^®cable.

ENJOYING INTERNET

Using the [Web Browser]

You can enter the website when you input the web address on the URL bar.

If you input the search word, it will ﬁnd the information about search word base on the

search engine.

1 Press the

button on the remote control.

2 Launch the [Web Browser] application.

1 2

4 5 6 7

You can refresh the web page you are viewing.

You can type in a web address to navigate to a speciﬁc website or enter a

search term directly.

You can view the tabs that are currently open.

You can block ads within the web page you are viewing.

However, this button is displayed only when

Block Ads] is set to [On].

[Settings] [Use

Split the screen to display the projector screen. You can browse web pages

while watching projector.

You can zoom in or out on the screen while browsing the website.

[Add to bookmarks]: You can add the website you are currently viewing to

your Favorites.

[History]: You can view and delete the website visit history.

[Bookmarks]: You can view and delete the list of websites you have added

to your Favorites.

[Settings]: You can change the web browser settings.

Exit the [Web Browser].

The new tab screen shows a list of [Recommended Sites] and [Most Visited

Sites].

If you do not want to display [Recommended Sites], set the

[Settings] [Show Recommended Sites] function to [Off].

[Recommended Sites] may vary by country and is only available in certain

countries.

• The [Web Browser] app on your projector is a browser for projector, so it may

work differently than the browser for your PC.

– Some of the content may not play properly.

– Flash Plug-in is not supported, and only HTML5 media is supported.

– Plug-in installation is not supported.

– Media in formats other than JPEG / PNG / GIF may not be played.

– Apps may be forced to shut down if the projector runs out of memory.

– The fonts provided on the projector are used. Depending on the content,

characters may look different from PC or mobile browsers.

– File and font downloads are not supported.

– Caution is required because malicious or phishing sites are not automatically

blocked.

– Some features may not be supported temporarily due to external factors of

the web browser.

• The website can be accessed through the projector's [Web Browser] app, so care

needs to be taken about children's access to harmful online contents.

You can lock the [Web Browser] app to prevent access to harmful online

contents.

Configure the settings in

[Application Locks].

(Q. Settings)

[General] [Safety]

Changing [Web Browser] Settings

Press at the top of the screen and select the [Settings].

• [On Startup]

You can set the startup page of the browser to [Open the New Tab page]/

[Continue where I left off]/[Home page:]/[Start from bookmark page].

• [Search Engines]

You can select the default search engine.

– Search engine settings may be subject to change without notice based on the

supplier’s circumstances.

• [Show Recommended Sites]

You can set whether or not to display a list of [Recommended Sites] on the new

tab screen.

• [Always Show Address Bar]

When set to [On], the address bar and menu bar area at the top will always be

displayed.

• [Private Browsing]

If set to [On], a history of website visits will not be stored.

• [Site Filtering]

You can register websites to block or allow.

[Approved Sites]: You can configure the settings to open the previously

registered web pages only.

[Blocked Sites]: You can configure the settings to block specific websites.

– To use the [Site Filtering] function, you should enter the projector password.

The initial password is set as “0000”.

• [Pop-up Blocker]

You can block pop-ups using the settings.

• [Do Not Track]

You can request to not leave a history of your visit on the website. The operation

may vary depending on the policy of the website.

• [Adaptive Streaming using JavaScript]

The media streaming technology using JavaScript allows you to view video with

optimized resolution.

If this is set to [Off], the resolution of the videos played in [Web Browser] is

limited to 720p.

• [Cookies Settings]

Enables the website to store and use cookie data.

• [Use Block Ads]

When set to [On], a button will appear in the menu bar area at the top of [Web

Browser] to turn the [Use Block Ads] feature on and off. Turning on the [Use

Block Ads] feature speeds up page loading by blocking ads included in the

website.

• [Automatic Web Browser Issue Report]

When set to [On], if a failure occurs due to insufficient memory (operation delay

or malfunction, media playback failure, page loading failure, abnormal shutdown,

etc.), the information is automatically sent to the LG Electronics (Korea) Web

Browser development team. The submitted information will only be used to

improve the Web Browser performance.

• [Clear Browsing Data]

[Clear Cookies]: Deletes cookie data. When deleted, you are logged out of most

sites.

[Clear All Browsing Data]: Deletes all browsing history, including cookies.

TOUR LIST OF SETTINGS

The conﬁgurable items differ depending upon model.

Quick Settings

Displays a set of light-weight controls quickly and simply such as [Picture Mode],

[Sound Out], [Sleep Timer] and so on.

Press the

(Q. Settings) button on the remote control.

You can set the [Picture Mode].

You can choose the [Sound Out].

You can set the [Sleep Timer].

Move to the [Network Connection Settings] screen.

You can set the [PJT Mode].

You can set more options.

You can add/delete the quick setting items or change their order.

• Press and hold the

Wheel (OK) or

(OK) on the remote control during

configuration to move to the corresponding menu.

[Picture]

[Picture Mode]

(Q. Settings)

[Picture] [Picture Mode Settings] [Picture Mode]

Select the picture mode that is best suited to your viewing environment, preferences

or video type.

Select a picture mode. You can ﬁne-tune the settings for each mode.

The conﬁgurable items differ depending upon model.

Depending upon the input signal, the available picture modes may be different.

When watching online service content, the Picture Mode may be changed to match the

content being shown.

When You Use Normal Signals

• [Vivid]

Sharpens the image by increasing the contrast, brightness and sharpness.

• [Standard]

Displays the picture with normal contrast, brightness, and sharpness levels.

• [Cinema]

Optimizes the screen for movies.

• [Sports]

Optimizes the screen for sports games. Sharpens the image of rapid movements

such as kicking or throwing a ball.

• [Game]

Optimizes the screen for gameplay.

• [HDR Effect]

This feature lets you enjoy a more dynamic, clearer image by correcting the light

and dark areas of the display. This feature provides a realistic image, even when

the source image’s gradation level is high.

– If you set [Picture Mode] to [HDR Effect], you will not be able to use some of

[Picture Mode Settings].

• [Brightest]

It displays the maximum screen brightness under appropriate image conditions.

• [Expert (Bright Room)]/[Expert (Dark Room)]

This mode is suitable for movies, etc. viewed in a dark environment.

[Expert (Dark Room)]] has lower color temperature than [Expert (Bright Room)].

Select a mode that is suitable for the movie you are watching.

When You Use the HDR

• [Vivid]

Sharpens the image by increasing the contrast, brightness and sharpness.

• [Standard]

In a normal viewing environment, it opens a screen that can properly show the

expressiveness and brightness of HDR.

• [Cinema Home]

The screen appears brighter and clearer than that of the [Cinema] screen.

• [Cinema]

Suitable picture for HDR video signal.

• [Game]

Optimizes the screen for gameplay.

• [Brightest]

It displays the maximum screen brightness under appropriate image conditions.

• If an HDR video signal is input to the models that do not support the HDR

technology, normal signal picture mode options will be made available.

• Depending upon the input signal, the available picture modes may be different.

• When watching online service content, the Picture Mode may be changed to

match the content being shown.

• [Picture Mode] changes may modify [Energy Saving] settings and it can affect

energy consumption. You can change the setting value in the [Energy Saving]

mode and the [Picture Mode Settings] [Picture Options] menu.

[Picture Mode Settings]

(Q. Settings)

[Picture] [Picture Mode Settings]

This feature allows you to adjust the selected picture mode in detail.

Depending upon the input signal or the selected picture mode, the available options

may differ.

The conﬁgurable items differ depending upon model.

• [Contrast]

Adjusts the contrast of the bright and dark areas of the picture. The closer to

100, the higher the contrast.

• [Brightness]

Adjusts the overall screen brightness. The closer to 100, the brighter the screen.

• [Sharpness]

Adjusts the sharpness of the image. The closer to 50, the sharper and clearer

the image.

• [Color]

Tones down or up the Colors displayed on the screen. The closer to 100, the

deeper the Color.

• [Tint]

Adjusts the Color balance between red and green displayed on the screen. The

closer to Red 50, the more red the Color will be. The closer to Green 50, the

more green the Color will be.

• [Color Temperature]

Adjusts the Color temperature cool/medium/warm.

• [Apply to All Inputs]

The settings you specify only applies to the currently selected input mode.

To apply your current picture settings to all input modes, select [Apply to All

Inputs].

• [Reset]

This option will reset the picture settings.

– You can reset the picture modes separately. Select the picture mode you wish

to reset and enable it.

[Advanced Controls]

(Q. Settings)

[Picture] [Picture Mode Settings] [Advanced

Controls]

Depending upon the input signal or the selected picture mode, the available options

may differ.

The conﬁgurable items differ depending upon model.

• [Dynamic Contrast]

Corrects the difference between the bright and dark areas of the screen for

optimal results depending on the brightness of the picture.

• [Dynamic Color]

Adjusts the Color and saturation of the picture to make the image more Colorful

and lively.

• [Color Gamut]

Selects the range of Colors to display.

• [Super Resolution]

Adjusts the resolution to make dim and blurred images clearer.

• [Gamma]

Adjusts the medium brightness of the picture.

Select [Low] for a bright picture, select [High1] or [High2] for a dark picture or

select [Medium] for medium brightness. [Expert (Bright Room)]/[Expert (Dark

Room)] can be selected from [1.9]/[2.2]/[2.4]/[BT.1886].

– [High2]/[BT.1886] expresses the gradation in ITU-R BT.1886, which is an

international standard.

• [White Balance]

Adjusts the overall color temperature of the screen as desired.

– [Method]: This method is used for ﬁne-tuning the color temperature setting.

You can control the color temperature at two points of the bright part and

dark part of the video if you select [2 Points], at each point of 10 levels if you

select [10 Points IRE], and at each point of 22 levels of the video if you select

[22 Points IRE].

– [Point]: Select screen brightness for color temperature adjustment.

If [Method] is set to [2 Points]; use Low to select shadows and High to select

highlights.

– [IRE]: Select screen brightness for color temperature adjustment.

When the [Method] is set to [10 Points IRE], you can select the brightness

with the 10 levels of brightness.

When the [Method] is set to [22 Points IRE], you can select the brightness

with the 22 levels of brightness.

– [Target Luminance]/[Adjusting Luminance]: You can adjust the selected

brightness by points.

• You can do these settings only when the [Picture Mode] is the [Expert

(Bright Room)] or the [Expert (Dark Room)] and when the [Method] is set

to [10 Points IRE] or [22 Points IRE].

– [Red]/[Green]/[Blue]: Adjust the color temperature of the selected point.

Adjust the intensity of [Red]/[Green]/[Blue] in the range of -50 to 50.

You can adjust respective values for the brightness selected in [Point].

• [Color Management System]

This is used when experts control it by using a test pattern. You can control it by

selecting areas of six colors ([Red]/[Green]/[Blue]/[Cyan]/[Magenta]/[Yellow]).

For normal images, adjustments may not result in noticeable Color changes.

– [Color]: From [Red]/[Green]/[Blue]/[Cyan]/[Magenta]/[Yellow], select a tone

to adjust.

– [Saturation]/[Tint]/[Luminance]: Adjust the chroma/tint/luminance of the

tone in the range of -30 to +30.

[Picture Options]

(Q. Settings)

[Picture] [Picture Mode Settings] [Picture Options]

Depending upon the input signal or the selected picture mode, the available options

may differ.

The conﬁgurable items differ depending upon model.

• [Noise Reduction]

Removes small dots that stand out so as to make the image clean.

• [MPEG Noise Reduction]

Reduces the noise produced during the creation of digital video signals.

• [Smooth Gradation]

It reduces jaggies in the picture for a smooth picture.

• [Black Level]

Adjusts the brightness of the dark parts of images.

– This feature can be used while watching content through an external input.

[Aspect Ratio]

(Q. Settings)

[Picture] [Aspect Ratio Settings] [Aspect Ratio]

Depending upon the input signal, the available screen sizes may be different.

The conﬁgurable items differ depending upon model.

The picture may get distorted while zooming in or out.

Selecting a different screen size from the original size may cause the image to look

different.

Depending on the combination of picture format and screen size, the edges may be

hidden or shown in black, or both sides of the picture may ﬂicker.

• [16:9]

Displays an aspect ratio of 16:9.

• [Original]

Changes the aspect ratio to 4:3 or 16:9 depending upon the input video signal.

• [4:3]

Displays an aspect ratio of 4:3.

• [Vertical Zoom]

You can adjust the vertical dimension of the screen and align the screen

vertically by using [Adjust Zoom Ratio] and [Adjust Screen Position].

When used in an image with a 21:9 ratio, the black bars on the top and bottom

of the screen disappear.

• [4-Way Zoom]

You can adjust the horizontal/vertical/diagonal dimensions of the screen and

align the screen horizontally/vertically by using [Adjust Zoom Ratio] and [Adjust

Screen Position].

[Just Scan]

(Q. Settings)

[Picture] [Aspect Ratio Settings] [Just Scan]

If you turn this feature [On], you can view the content in the aspect ratio that is in

content source. If the edge of the screen is not clean, please turn it [Off].

If set to [Auto], the feature switches between [On] or [Off] status depending on the

information contained in the video signal.

• The items that can be selected may vary depending on the current input.

[Energy Saving]

(Q. Settings)

[Picture] [Energy Saving]

Reduces power consumption by adjusting peak screen brightness.

If you use [Energy Saving] function, brightness of your projector will be affected.

• [Minimum]/[Medium]/[Maximum]

Applies the pre-set [Energy Saving] mode.

[Sound]

[Sound Mode]

(Q. Settings)

[Sound] [Sound Mode Settings] [Sound Mode]

You can select the most suitable sound mode for each genre.

• [AI Sound]

Automatically optimize sound based on content type.

• [Standard]

Optimizes the sound for all types of content.

• [Cinema]

Optimizes the sound for cinemas.

• [Clear Voice III]

Boosts voice clarity.

• [Sports]

Optimizes the sound for sports.

• [Music]

Optimizes the sound for music.

• [Game]

Optimizes the sound for gameplay.

[Sound Mode Settings]

(Q. Settings)

[Sound] [Sound Mode Settings]

The conﬁgurable items differ depending upon model.

• [Sound Mode]

You can select the most suitable sound mode for each genre.

• [Balance]

You can adjust the volume of the left and right speakers.

• [Virtual Surround Plus]

Enjoy an immersive soundscape with the virtual multi-channel surround sound

effect.

– The option can be enabled if [Sound Mode] is set to [Standard].

• [Equalizer]

You can set the desired sound by adjusting the equalizer directly.

(100 Hz/300 Hz/1 kHz/3 kHz/10 kHz)

– The option can be enabled if [Sound Mode] is set to [Standard].

• [Reset]

You can reset the sound effect settings.

– The option can be enabled if [Sound Mode] is set to [Standard].

[Sound Out]

The conﬁgurable items differ depending upon model.

Playing audio through the projector's internal speakers

(Q. Settings)

[Sound] [Sound Out] [Internal Projector Speaker]

Audio is played through the projector’s internal speakers.

Connecting and Using an Audio Device Wirelessly

(Q. Settings)

[Sound] [Sound Out] [Bluetooth]

You can connect wirelessly a Bluetooth audio device or a Bluetooth headset to enjoy

your projector’s sound in richer quality and greater convenience.

Refer to the user manual of the Bluetooth audio device for details on how to connect

and use the device.

• Press

to view the connected devices or any devices that can be connected

and connect to any one of them.

• [LG Sound Sync] devices will automatically try to connect to the recently used

devices when you turn the projector on.

• We recommend that you connect an LG audio device that supports LG Sound

Sync, using LG TV mode or LG Sound Sync mode on device.

• Some models may not be supported.

• If the device fails to connect, check the power of the device to connect to and

check if the audio device is working properly.

• Depending on the type of the Bluetooth device, the device may not connect

correctly or an abnormal behavior may occur such as unsynchronized video and

audio. (The mobile-only headsets may not work.)

• Sound may stutter or sound quality may be reduced if:

– the Bluetooth device is too far from the projector;

– there are obstacles between the Bluetooth device and the projector; or

– used together with radio equipment such as a microwave oven or wireless

LAN.

• If the [Picture Mode] is set to [Game] and [Sound Out] is set to [Bluetooth],

[Picture Mode] changes to [Standard].

• If you continue to experience problems, we recommend using a wired connection.

(Optical digital, HDMI (ARC) port)

• Using Bluetooth speakers that support Dual mode/Double mode/2-Channel

mode together with the Magic Lighting Remote may limit the speakers’ usability.

Connect and Use an Audio Device that Supports Optical Digital

(Q. Settings)

[Sound] [Sound Out] [Optical]

You can connect an audio device that supports [Optical] to the optical digital audio

output port to enjoy your projector’s sound in richer quality and greater convenience.

• Only available for models with an optical digital port.

• You can use the projector remote control to adjust the volume of the connected

device.

Hearing Sound through an External Audio Device Connected via a HDMI (ARC)

Port

(Q. Settings)

[Sound] [Sound Out] [HDMI ARC]

Sound from the projector can be output through an external audio device connected via

a HDMI (ARC) port.

• Select [HDMI ARC] to automatically turn on SIMPLINK. Once SIMPLINK is turned

off, the output speaker settings automatically revert to the default settings for

uninterrupted audio output.

Using Wired Headphones

(Q. Settings)

[Sound] [Sound Out] [Wired Headphones]

Select [Wired Headphones] to optimize audio output according to the device

connected.

• Only available for models with a Wired Headphones port.

• Some models may not be supported.

• If you connect the wired headphones while the projector is powered on, it

automatically detects the wired headphones and redirects audio through them.

Playing audio through the projector’s internal speakers and external audio

device simultaneously

Audio can be played through multiple devices simultaneously.

• Using [Optical + Internal Projector Speaker]

(Q. Settings)

[Sound] [Sound Out] [Optical + Internal

Projector Speaker]

Audio is played through the projector’s built-in speakers and the audio device

connected to the digital optical audio output port simultaneously.

– Only available for models with an optical digital port.

• Using [Wired Headphones + Internal Projector Speaker]

(Q. Settings)

[Sound] [Sound Out] [Wired Headphones +

Internal Projector Speaker]

Audio is played through the projector’s internal speakers and the wired

headphones simultaneously.

– If you connect the wired headphones while the projector is powered on, it

automatically detects the wired headphones and redirects audio through

them.

– Only available for models with a Wired Headphones port.

– Some models may not be supported.

[Auto Volume]

(Q. Settings)

[Sound] [Additional Settings] [Auto Volume]

When you set to [On], the volume is automatically adjusted.

[AV Sync Adjustment]

(Q. Settings)

[Sound] [Additional Settings] [AV Sync Adjustment]

Adjusts the synchronization of the sound from the speaker that is working.

The closer to (>), the slower the audio output.

If you select the [Bypass], Outputs the sound from external devices without any audio

delay. The audio may be output before the video because of the time the projector

takes to process the video input.

• The adjustable items vary depending on [Sound Out].

[HDMI Input Audio Format]

(Q. Settings)

Format]

[Sound] [Additional Settings] [HDMI Input Audio

You can set the audio format for each HDMI input. When the voice delivered through

the HDMI port is not synchronized, set it to [PCM].

[LG Sound Sync]

(Q. Settings)

[Sound] [Additional Settings] [LG Sound Sync]

Connect the [LG Sound Sync] device to the optical digital input port and set [Sound

Out] to [Optical]. By setting this feature to [On], you can adjust the volume of the

connected [LG Sound Sync] device using a projector remote control.

• If the auto-power feature of the sound bar that supports [LG Sound Sync] is

set to On, the sound bar will be turned on or off together when the projector is

turned on or off.

[Digital Sound Out]

(Q. Settings)

[Sound] [Additional Settings] [Digital Sound Out]

You can conﬁgure the [Digital Sound Out] settings.

• These settings are available only when an [Optical]/[HDMI ARC] is selected.

• When [Pass Through] is enabled, sound effects may not be output.

• The codec output with a device may differ from input signals.

Sound Input

Digital Sound Output

[PCM]

All

PCM

MPEG

Dolby Digital

[Auto]

/ [Pass

Through]

(Optical) Dolby Digital

(HDMI ARC) Dolby Digital Plus

Dolby Digital Plus

(Optical) Dolby Digital

(HDMI ARC) Dolby Digital Plus

Dolby TrueHD (HDMI

only)

HE-AAC

Dolby Digital

[Connection]

[Projector Name]

(Q. Settings)

[Connection] [Projector Name]

You can use the screen keyboard to set the name for the smart projector to be used on

the network.

• Up to 25 characters can be entered using the English alphabet.

[Network Connection Settings]

(Q. Settings)

[Connection] [Network Connection Settings]

If you conﬁgure settings for the network, you can use various services such as online

contents and applications.

[Wired Connection (Ethernet)]

Select [Wired Connection (Ethernet)].

If the router connected to the network supports the DHCP feature, connecting the

projector and router by wire will automatically connects to the network.

If the automatic setup is not supported, you can select [Edit] to manually set up the

network connection.

• The IPv6 setup does not support [Edit].

[Wi-Fi Connection]

Select [Wi-Fi Connection].

If you have set up the projector for a wireless network, you can check and connect to

the available wireless Internet networks.

• [Add a Hidden Wireless Network]

If you input the name of network directly, you can add a wireless network.

• [Connect via WPS PBC]

If the wireless router you want to connect to has a Wi-Fi Protected Setup-Push

Button Configuration (WPS-PBC) feature, you can easily connect to the wireless

router by pressing the WPS-PBC button on the router. Press the wireless

router’s WPS-PBC button and then press the projector’s [Connect] button.

• [Connect via WPS PIN]

This is a method to connect to an access point using a Wi-Fi Protected Setup-

Personal Identification Number (WPS-PIN). Select the access point (AP) to

which you would like to connect. Enter the PIN displayed on the access point’s

Wi-Fi device.

• [Advanced Wi-Fi Settings]

Once you connect to a wireless network you can view connection information

such as detailed IP address information. In addition, you can change the IP

address and DNS server address you want to connect to by pressing the [Edit]

button.

– The IPv6 setup does not support [Edit].

[Device Connection Settings]

(Q. Settings)

[Connection] [Device Connection Settings]

You can link the information about the devices connected to the projector and

conﬁgure settings related to operations.

The conﬁgurable items differ depending upon model.

• [Auto Device Detection]

It automatically sets to enable you to control the devices connected via the

HDMI with the Magic Lighting Remote.

• [SIMPLINK (HDMI-CEC)]

You can conveniently control and use various multimedia devices connected

through HDMI with the projector’s remote control.

• [Auto Power Sync]

If [Auto Power Sync] is set to [On], turning on a SIMPLINK-linked device will turn

the projector on. When you turn off the projector, the device will also be turned

off.

• [LG Wireless Keyboard]

This feature enables you to connect a LG wireless keyboard to your device.

Turn on the device, set it to pairing mode, and then click [Connect] on your

projector screen.

If there is a LG wireless keyboard previously connected, it will be automatically

reconnected to your projector once your projector turns on. To disconnect the

existing connection, click [Disconnect].

– Supported keyboard: LG Rolly Keyboard

• [Universal Control Settings]

You can set up the universal remote control.

[Mobile Connection Management]

(Q. Settings) [Connection] [Mobile Connection Management]

You can set to use a smart device connected to the projector to control the projector

or manage the connection history.

• [Projector On With Mobile]

If [Turn on via Wi-Fi] or [Turn on via Bluetooth] is set to [On], you can turn on

your projector using an application that supports [Projector On With Mobile] or

see the screen of the application on your projector.

– The projector should be connected to a network.

– The projector and the device to be used should be connected to the same

network.

– The [Turn on via Wi-Fi] feature must be used in an app on a smart device that

supports the feature.

– The [Turn on via Bluetooth] feature can only be used with certain LG

Electronics smartphones.

– The projector must be plugged in.

– To connect for the ﬁrst time, make sure the device to be used is ready to

connect.

– Some models may not be supported.

• [Screen Share]

By tapping [Screen Share], you can delete the connection history of devices

which have been connected to the projector using the Screen Share function.

• [Sound Share]

You can delete the connection history of the smart device that was connected

to the projector via Bluetooth.

[General]

[AI Service]

(Q. Settings)

[General] [AI Service]

You can enable the recommended services based on the usage history.

The conﬁgurable items differ depending upon model.

• [AI Sound]

When set to [On], the image quality is automatically optimized for content

characteristics based on the algorithms learned with deep learning techniques.

– This setting is only available for Internal Projector Speaker.

– If you set this function to [On],

(Q. Settings)

[Sound] [Sound

Mode Settings] [Sound Mode] is changed to [AI Sound].

• [AI Recommendation]

You can get content recommendations messages according to your content

viewing history and app usage history.

– [Content Recommendations]: You can get content recommendations or

introductions to new features based on your pattern of viewing content and

using apps.

– [Network-Based Personalization Recommendations]: You can get

recommendations for viewing history base channels and content through the

network.

• [On]: Get more recommendations through the server.

• [Off]: We recommend basic contents based on your viewing history.

– [Delete Usage Data]: It resets the content view history and the app usage

history. If you reset them, it takes some time to receive recommendations for

contents again.

[Language]

(Q. Settings)

[General] [Language]

You can choose the menu language displayed on the screen.

• [Menu Language]

You can select one of the menu languages to be displayed on the screen.

• [Keyboard Languages]

Select the language to use the on-screen keyboard.

[Location]

(Q. Settings)

[General] [Location]

You can change the location setting of your projector.

The conﬁgurable items differ depending upon model.

• [Service Area Zip Code]

You can set the detailed location.

• [LG Services Country]

Select the country where you want to access LG’s services. Services may vary

depending on location.

– You must set the country manually when you are not connected to the

network.

[Time]

(Q. Settings)

[General] [Time]

You can check or change the time while watching content on the projector.

• [Set Automatically]

Automatically sets the time displayed on the projector screen.

• [Time]/[Date]/[Time Zone]

You can manually set the date and time, etc.

• [Custom Time Zone]

When select the [Custom] in [Time Zone], [Custom Time Zone] menu is

activated.

[Sleep Timer]

(Q. Settings)

[General] [Time] [Timers] [Sleep Timer]

Sets the projector to turn off at a speciﬁed time.

If you want to disable [Sleep Timer], select [Off].

[Power On Timer]

(Q. Settings)

[General] [Time] [Timers] [Power On Timer]

Set [Power On Timer] to [On].

The projector turns on at the set time.

To use [Power On Timer], set the time correctly.

• [Time]: Set the power-on time.

• [Timer Repeat]: Set the day of the week. Set the option to [None] to operate the

feature only once.

• [Input]: Set an external input to display when the power is turned on.

• [Volume]: Set audio volume to use when the power is turned on.

[Power Off Timer]

(Q. Settings)

[General] [Time] [Timers] [Power Off Timer]

Set [Power Off Timer] to [On].

The projector is turned off at the set time.

To use [Power Off Timer], set the time correctly.

• [Time]: Set the time at which to turn the projector off.

• [Timer Repeat]: Set the day of the week. Set the option to [None] to operate the

feature only once.

[Auto Off]

(Q. Settings)

[General] [Time] [Timers] [Auto Off]

If there is no input signal or button press, the projector automatically turns off after the

preset time has elapsed.

[Safety]

• Set [Safety] to [On].

• The initial password is set as “0000”.

Enabling [Application Locks]

(Q. Settings)

app you want

[General] [Safety] [Application Locks] Choose the

You can lock or unlock the application.

• The lock function is not immediately available for the currently running

application.

Enabling [Input Locks]

(Q. Settings)

[General] [Safety] [Input Locks] Select the

desired external input

You can lock or unlock the Input Locks.

Reset Password

(Q. Settings)

[General] [Safety] [Reset Password]

Set or change the password for the projector.

Resetting a Lost Password

If you lose the password you set, you can reset it as follows:

1 Press the

[General] [Safety].

2 Press

master password input window will appear.

(Q. Settings) button on the remote control and select

on the remote control. The

3 Enter the numbers “0313” in the master password input window, then press

[Enter]. The password will be reset.

[PJT Mode]

(Q. Settings)

[General] [PJT Mode]

This function turns the projected image upside down or ﬂips horizontal.

[Auto Keystone]

(Q. Settings)

[General] [Auto Keystone]

[Auto Keystone] provides a rectangular screen image by automatically adjusting the

keystone number when there is a trapezoidal screen image caused by tilting of the

projector.

• [On]

Automatically adjusts the keystone number.

• [Off]

Manually adjusts the keystone number.

• Some models may not be supported.

[Edge Adjustment]

(Q. Settings)

[General] [Edge Adjustment]

[Edge Adjustment] adjusts the horizontal and vertical sides of the projected image if

the projector is at an angle and not perpendicular to the screen. This feature ensures

the shape of the projected image is not distorted.

Use this feature only when the projector cannot be set up at the optimal angle. [Edge

Adjustment] may result in a loss of image quality.

• Some models may not be supported.

[Account Management]

Creating LG Account

(Q. Settings)

In]

[General] [Account Management] [LG Account Sign

In [Account Management], you can use your email address to create a new LG account.

Alternatively, you can create and log in to an LG account using the ID and password of

an external service account.

1 Select [Create Account]. Read and accept the Terms of Service.

2 Enter an ID and a password. Your ID must be your email address.

3 Select [OK]. Go to your email to verify your email address. Please verify your

email before the time expires.

4 If email veriﬁcation is successful, an LG account is created and you can log in

with this account information.

• Internet connection is required to create an account.

• You may be restricted from the service depending upon your age.

Managing your LG Account

(Q. Settings)

You can manage the information of your LG account.

• Select (Q. Settings) [General] [Account Management] to log in.

• [Personal Information]

[General] [Account Management]

You can view basic information about the logged in account.

You can change the password or press [Edit] to edit your personal information.

– Some models may not be supported.

[Home Auto Launch]

(Q. Settings)

[General] [Home Auto Launch]

You can set Home to launch automatically when turning on the projector.

• The configurable items differ depending upon model.

[Pointer Options]

(Q. Settings)

[General] [Additional Settings] [Pointer Options]

You can set the pointer speed and size you want while it is on the screen.

[Settings Help]

(Q. Settings)

[General] [Additional Settings] [Settings Help]

If you select the setting menus, you will see the hints of the settings. Turn on/off

description box in settings.

[Menu Transparency]

(Q. Settings)

[General] [Additional Settings] [Menu Transparency]

By setting this feature to [On], you can make some of the menus (e.g. Search, etc.)

transparent.

[Screen Saver]

(Q. Settings)

[General] [Additional Settings] [Screen Saver]

When the currently displayed app has not received any user input for an hour, it will be

replaced by a [Screen Saver].

• Setting the [Screen Saver] feature to [Off], maintains the same display for an

extended period, which may compromises quality. The compromised screen may

not be recoverable.

[Eco Mode]

(Q. Settings)

[General] [Additional Settings] [Eco Mode]

Set power options to reduce energy consumption.

The name of this functions may differ depending on region.

• [Auto Power Off]

Set the projector to turn off automatically when there has been no user input

for a specified amount of time.

• [HDD Eco Mode]

If you set the mode to [On], the USB HDD connected to the projector will go into

power-saving mode when it has been left unattended for an extended period of

time.

[Home/Store Mode]

(Q. Settings)

[General] [Additional Settings] [Home/Store Mode]

You can choose between [Home Mode] and [Store Mode].

To use the projector at home, select [Home Mode].

Select [Store Mode] only when the projector will be displayed in store. The [Store

Mode] provide settings optimized for store display.

[Auto Power]

(Q. Settings)

[General] [Additional Settings] [Auto Power]

Makes the projector turn on automatically when the power cord is connected to the

projector.

• [On]

When the power cord is connected to the projector, it turns on automatically.

• [Off]

When the power cord is connected to the projector, it goes into standby mode.

[High Altitude]

(Q. Settings)

[General] [Additional Settings] [High Altitude]

If the projector is used at an altitude higher than 1200 meters, turn this on.

Otherwise, the projector may overheat or its protection function may be activated. If

this happens, turn the projector off and then on again after waiting for several minutes.

• Some models may not be supported.

[Accessibility]

[High Contrast]

(Q. Settings)

[Accessibility] [High Contrast]

When this feature is set to [On], it adjusts the background of some of the menus on

the screen and font colors to highlight the contrast between the light and dark areas.

[Grayscale]

(Q. Settings)

[Accessibility] [Grayscale]

You can see the items more clearly by changing the color of the menu provided on the

image and screen to black and white. Set to [On].

[Invert Colors]

(Q. Settings)

[Accessibility] [Invert Colors]

To enhance the visibility of the menus on the screen, you can invert and calibrate

certain colors in some menus. Set to [On].

[Support]

[Software Update]

(Q. Settings)

[Support] [Software Update]

If the software needs to be updated, run Software Update to apply the latest software

version for use.

• [Allow Automatic Updates]

If set to [On], updates will be proceeded automatically without asking when

there is a new update after a version check.

• [Check for Updates]

When checking for the latest update version, you can perform updates only if an

update file of a later version is available. The projector automatically checks your

software version but, if necessary, you can perform a manual check.

• The configurable items differ depending upon model.

• The latest version can be obtained via internet connections.

• If software is not updated, certain functions may not work properly.

• In some countries, [Allow Automatic Updates] is not displayed if you are not

connected to the internet.

[Projector Information]

(Q. Settings)

[Support] [Projector Information]

You can check information such as [Model], [Serial Number] and [Device Name].

[Notifications]

(Q. Settings)

[Support] [Notiﬁcations]

You can view all notiﬁcations from projector apps and LG service at the same time. You

can view and delete each notiﬁcation message, and directly move to the app or website

using notiﬁcations that support shortcuts.

[Additional Settings]

(Q. Settings)

[Support] [Additional Settings]

The conﬁgurable items differ depending upon model.

• [Picture Test]

Start the [Picture Test] to check that the video signal output is normal, and then

select whether there is an error.

If you have found no problems in the test, then check the connected external

device.

• [Sound Test]

Start the [Sound Test] to check that the sound signal output is normal, and then

select whether there is an error.

If you have found no problems in the test, then check the connected external

device.

– Sound test is possible by Internal projector Speaker only.

• [User Agreements]

These are the terms and conditions for privacy for the use of Smart projector-

related services.

• [Legal Notice]

It's a legal notice for services provided via projector.

• [Open Source Software Notice]

You can view the instructions for each item.

[Reset to Initial Settings]

(Q. Settings)

[Support] [Reset to Initial Settings]

Return projector to its initial settings. This will revert all settings to their default values.

After reset, the projector will automatically turn off and on.

• If [Safety] is set to [On], you should type the password to [Reset to Initial

Settings].

• Do not turn off the power during initialization.

• We recommended that you reset the projector to [Reset to Initial Settings]

before you sell it or transfer it to a third party.

TROUBLESHOOTING

Please check the list below when you experience the following symptoms during use of

the product. It may not be a failure.

Information on customer service for product problems is available in

[Support] on the projector.

(Q. Settings)

Perform Check-up with the [Quick Help].

When the projector malfunctions, you can get help to solve the problem.

Push the

(Q. Settings) button of the remote control to select

[Support]

[Quick Help].

You can also long-press the number

[Quick Help].

button of the remote control to run the

• [Optimization Settings]

You can automatically check the overall status of your projector and view and

change the recommended setting values.

• [Check Items]

Select the problematic item, and you can get help to solve the problem.

– [Self-Diagnosis of Projector Settings]: Select the item that matches the

symptom to ﬁnd instructions that can help you solve the problem.

– [Check the status of Projector]: You can check your projector’s current status

for the selected item.

• [LG Remote Service]

You can get help in solving the problem via Remote Service.

– Some models may not be supported.

• When there is no related content in the [Quick Help], please refer to the

Troubleshooting.

• If you still fail to solve the problem, please contact our customer service center.

Abnormal behavior

Power/Remote Control Errors

I cannot turn on the Projector.

• Please make sure your projector power plug is correctly connected to the outlet.

• If you are using a multi-outlet, check if it is working properly. To check whether a

power strip is working properly, plug the projector’s power plug directly to a wall

outlet and observe its operation.

• Try to power on using the button on your projector set.

The screen does not appear for some time after power-on.

• This is because there is a noise-removal process to eliminate any possible noise

that may appear during power-on. This does not mean the product is defective.

I cannot turn the projector on with the remote control.

• Please make sure your projector power plug is correctly connected to the outlet.

• Replace the batteries in the remote control. (Use alkaline batteries.)

• Check whether there are any obstacles in front of the projector’s remote control

sensor. Sound bars or other obstacles placed in front of the projector’s lower

receiver may obstruct IR signal reception.

The pointer of Magic Lighting Remote does not appear on the screen.

• This feature can only be used with the Magic Lighting Remote. (The provided

remote control differ depending upon model.)

• Hold the remote control towards the projector and long-press

button until

the instruction appears. The previously registered remote control is deregistered

and then registered again.

• Replace the batteries when you are prompted to do so on your projector screen.

(Use alkaline batteries.)

The power turns off suddenly.

• Check whether the [Power Off Timer], [Auto Off], or [Auto Power Off] is set.

• There is also a chance that the internal protection circuitry has activated because

the internal temperature of the product has risen unusually or excessively.

Screen Problems

First of all, perform a

(Q. Settings)

[Support] [Additional Settings]

[Picture Test] to check for any abnormalities in the projector.

If you are using a set-top box, turn it off, and then turn it back on.

Make sure that the set-top box is correctly connected to your projector.

It says there is no signal on the screen.

• Check if the cable connected to the external device is properly connected to the

projector.

• Go to

to choose the connected input.

• Check if your external device, such as set-top box or Blu-ray player, is turned on.

The screen shakes after the momentary appearance of vertical/horizontal lines

and net pattern.

• Stop using items such as wireless telephones, hairdryers, electrical drills etc. The

problem is caused by high-frequency electronic devices such as another projector

or strong electromagnetic sources.

I see vertical lines in all four directions on the screen, or colors are blurred

when I try to connect to HDMI.

•

(Q. Settings)

[Picture] [Aspect Ratio Settings] [Just Scan]

Set [Just Scan] to [Off].

[Just Scan] shows you the original image as it is. You may see noise in all four

directions on the screen if the signal contains noise.

I don’t see anything, or the image keeps ﬂickering when i try to connect the

HDMI^®cable.

• Check whether your HDMI^®cable is compliant with the specifications. You may

experience flickering or a blank screen if the HDMI^®cable is faulty (bent, broken).

• Make sure that the cable is correctly connected to the port. Bad or loose contact

may cause display problems on the screen.

The screen looks too dim or dark.

•

(Q. Settings)

Mode]

[Picture] [Picture Mode Settings] [Picture

Switch [Picture Mode] to your desired picture mode. ([Standard] etc.) This

applies to the current input mode only.

•

(Q. Settings)

[Picture] [Energy Saving]

Switch [Energy Saving] to [Minimum].

The screen is in black and white or displaying strange colors.

• Check the input mode or cable connection.

• Go to

to choose the connected input.

• Check the [High Contrast], [Grayscale] and [Invert Colors] settings.

Sound Problems

First of all, perform a

(Q. Settings)

[Support] [Additional Settings]

[Sound Test] to check for any abnormalities in the projector.

If you are using a set-top box, turn it off, and then turn it back on.

Make sure that the set-top box is correctly connected to your projector.

The screen is ﬁne, but it does not play any sound.

• If you use a set-top box, there will be no sound if you have set the volume of

the set-top box or your projector to 0 or enabled Mute. Set the volume to an

appropriate level.

•

(Q. Settings)

[Sound] [Sound Out]

Set the [Sound Out] to [Internal Projector Speaker], and then check it once

again. If you can hear the sound just fine, you need to set the external speakers

connected such as a soundbar.

There is no sound coming from one of the speakers.

(Q. Settings) [Sound] [Sound Mode Settings] [Balance]

Adjust the balance as necessary with the Navigation button in [Balance].

•

PC Connection Problems

Press the

button on your remote control. Select

[Edit] located at the

top right of [Home Dashboard]. In the edit mode, set the icon of the HDMI terminal

connected to the PC to PC to apply the video and aspect ratio settings that are aligned

with the PC.

To connect a different device to the same input terminal, you need to set the icon again

because the settings of the edit icon will not be automatically restored.

The screen remains blank after it is connected to a PC.

• Check that the PC is properly connected to the projector.

• Turn the projector off and back on using the remote control.

• Restart the PC with the projector on.

• Make sure that the output resolution set on the PC is set to the HDMI-PC

supported resolution of the projector.

• To use dual monitors, check that the PC or notebook supports dual-monitor

mode.

• Reconnect the high speed HDMI^®cable.

• If you have connected the RGB output port of your PC to the HDMI input port or

your projector. You need an RGB to HDMI gender.

You will not see anything on the screen if you use an HDMI to RGB gender.

The screen is cut off or moved to one side after it is connected to a PC.

• Set the PC’s resolution to one supported by the projector.

• Set the connected HDMI device’s name to PC.

Press the

button on your remote control. Select

[Edit] located at the

top right of [Home Dashboard]. Change the icon of the HDMI port connected to

[Inputs] to PC and select [Save].

The sound does not play when the PC is connected with an HDMI^®cable.

• In PC settings, set Control Panel Sound Play LG projector as the default

device.

• Consult your manufacturer on whether your graphics card supports HDMI audio

output.

[Photo & Video] Movie Playback Problems

For more information about supported ﬁles, see “[Photo & Video]”.

I cannot ﬁnd a ﬁle in the [Photo & Video].

• Check that the files on the USB storage device can be read by a PC.

• Check that the file extension is supported.

I get a message saying “This ﬁle is not supported” or the sound is playing

normally but the video is not.

• Check that the file plays without any problems on a PC’s video player. Also check

for file damage.

• Check that the file extension is supported.

• Check that the resolution is supported.

• Check that the video codec is supported.

• Check that the frame rate is supported.

I get a message saying “This audio is not supported” or the video is playing

normally but the audio is not.

• Check that the file plays without any problems on a PC’s video player. Also check

for file damage.

• Check that the file extension is supported.

• Check that the audio codec is supported.

• Check that the bit rate is supported.

• Check that the sample rate is supported.

• Check that the audio channel separation is supported.

I cannot see the subtitles.

• Check that the file plays without any problems on a PC’s video player. Also check

for file damage.

• Check that the video and subtitle files have the same name.

• Also check that both the video file and the subtitle file are in the same folder.

• Check that the subtitle file format is supported.

• Check that the language is supported. (You can check the language of the

subtitle file by opening the file in the Notepad.)

If subtitles encoding is incorrectly set, subtitles may not be displayed properly.

Select

in the control panel at the bottom of the video playback

screen and change the [CODE PAGE] value.

• If you play a video file stored on another device by using the content sharing

feature, subtitles may not be available depending on the program you use.

• Subtitles are not supported if you are playing video through an NAS unit. Consult

your NAS manufacturer.

My USB storage device is not recognized when connected.

• Check whether it is a USB storage device supported by the projector.

For details, please refer to “Connecting USB ”.

Network Connection Problems

You can check the network connection status as shown below.

•

(Q. Settings)

[Connection] [Network Connection Settings]

[Wired Connection (Ethernet)]

•

(Q. Settings)

[Connection] [Network Connection Settings]

[Wi-Fi Connection] [Advanced Wi-Fi Settings]

When X appears next to projector

• Check the projector or the AP (Router).

• Check the connection status of the projector, AP (Router) and Cable Modem.

• Power off and power on in the following order;

1. The Cable Modem, wait for the Cable Modem to reset.

2. The AP (Router), wait for the AP (Router) to reset.

3. The projector.

• If you want to establish a wired LAN connection check whether an IP address

can be obtained from your router properly. If you are setting up your network

manually check whether all settings are correct.

• If you want to establish a wireless connection check the following points as well.

1. Set your router’s SSID (network name) or wireless channel.

2. Set your router’s security key.

If you do not know this setting, check the router's instruction manual and the

manual provided by the Internet provider. If you are still not sure, contact the

router company or the Internet company.

• If you are using a wireless connection, change the SSID (Network name) and

wireless channel of AP (Router).

• If you are using a static IP, enter the IP directly.

• Contact internet service provider or AP (Router) companies.

When X appears next to Gateway

• Check the AP (Router) or consult your Internet service provider.

• Unplug the power cord of the AP (Router), Cable Modem, wait 10 seconds.

Reapply power.

• Initialize (Reset) on the AP (Router) or Cable Modem.

• Contact internet service provider or AP (Router) companies.

• Check the AP (Router) manufacturer’s website to make sure your router has the

latest firmware version installed.

• If you do not know this setting, check the router's instruction manual and the

manual provided by the Internet provider. If you are still not sure, contact the

router company or the Internet company.

When X appears next to DNS

• Check the AP (Router) or consult your Internet service provider.

• Unplug the power cord of the AP (Router), Cable Modem, wait 10 seconds.

Reapply power.

• Initialize (Reset) on the AP (Router) or Cable Modem.

• Check that the MAC address of the projector/AP (Router) is registered with

your Internet service provider. (The MAC address displayed on the pane of the

network status window should be registered with your Internet service provider.)

• If you do not know this setting, check the router's instruction manual and the

manual provided by the Internet provider. If you are still not sure, contact the

router company or the Internet company.

LG Account Problems

In some countries, access to the website (www.lgappstv.com) may be restricted.

I have already signed up on the projector. Do I still have to sign up again at the

website (www.lgappstv.com)?

• You can use the website with the membership information that you used when

signing up on projector.

You can use the website by logging in to the website with the ID and password

you used when signing up on projector, entering additional information and

completing the email verification process.

I forgot my Password. What should I do?

• On the projector's login screen, select the [Forgot Password?] button to go to

the find password page. Enter your email address on the find password page,

and we'll send you a link to reset your password.

• You can also reset your password in LG Account Reset Password on the

website (www.lgappstv.com).

Internet Browser Problems

Some parts of a particular website are not visible when I am using the Internet.

• The [Web Browser] supports only HTML5 media and not Flash Plug-in.

• The [Web Browser] does not support plug-in installation.

• On the [Web Browser], it may not be possible to play media files in formats

other than JPEG/PNG/GIF.

• You cannot save attachments or images.

• If the [Use Block Ads] feature is turned on, the area on the website that appears

to show an ad will appear blank. If some of the content of the website is blocked

and is not displayed, try setting

[Web Browser].

[Settings] [Use Block Ads] to [Off] in

The Internet browser automatically shuts down when I visit a website.

• The Internet browser may be forced to shut down if the available memory size is

not sufficient to accommodate the image information for a website.

When watching a video in [Web Browser], the video is forced off.

• You may be able to fix this by setting

[Settings] [Adaptive Streaming

using JavaScript] to [Off] in [Web Browser]. The setting is not applied to tabs

that were open before the change, and is only applied to tabs opened after the

change.

York Dj 060 User Manual
Toshiba Gf632 User Manual
Sharp Plasmacluster Air Purifier Replacement Filter Set 74000661776 User Manual
Sharp Humidification Replacement Filter For Kc 850u Or Kc 860u Fz C100mfu User Manual
Ram Mounting Systems 5500 User Manual
Panasonic Kx Ft31bx User Manual
NEC NP510WS User Manual
LG CORDZERO A9 User Manual
ENDRESS HAUSER FMR255 User Manual
BLACK DECKER ST7700 User Manual