KDC-X704
KDC-BT378U
KDC-BT360U
KDC-BT34
KDC-BT278U
KDC-MP378BT
KMR-D378BT
KDC-X304
KDC-BT778HD
CIND-SRETCERIVUERCTION MANUAL
AUTORADIO CD
MODE D’EMPLOI
RECEPTOR CD
MANUAL DE INSTRUCCIONES
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial
numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X704/KDC-X304/KDC-BT778HD/KDC-BT378U/KDC-BT360U/KDC-BT34/KDC-BT278U/KDC-MP378BT/KMR-D378BT
Serial number
US Residents Only
Register Online
Register your Kenwood product at http://www.kenwood.com/usa/
© 2019 JVC KENWOOD Corporation
B5A-3139-00 (KN)
IC (Industry Canada) Caution
CAUTION
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at
least 20 cm or more away from person’s body.
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices
d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit
être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.
Attention de ‘IC (Industrie Canada)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage.
Para cumplimiento de la IFT:
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada”
Contains Bluetooth Module
FCC ID: ZWY88112
IC ID: 12033A-88112
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
ii
Article 4
Right pertaining to the Licensed Software
SOFTWARE LICENSE AGREEMENT
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is
copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions
which Users shall follow in order to use the Licensed Software.
Any and all copyrights and other rights pertaining to the Licensed Software and related documents
shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or
sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be
entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any
related documents.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the
Product in which the "Licensed Software" is embedded.
Article 5
Indemnification of Licensor
The Licensed Software may include the software which has been licensed to the Licensor directly or
indirectly from any third party. In such case, some third parties require the Users to follow their conditions
for use separately from this Software License Agreement. Such software shall not be subject to this
Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided
separately below.
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User
or any third party due to the exercise of the license granted to the User under this Agreement, unless
otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with
certain objective of the Licensed Software.
Article 1
General Provision
Article 6
Liability to Third Party
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case
referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.
(the country where the User bought the Product (hereinafter the "Country")
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any
other intellectual property right that was caused by the User's use of the Licensed Software, the User shall
settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any
inconvenience it may cause.
Article 2
License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the
Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed
Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall
not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation
manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright
Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 7
Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof
or any other information to be granted under this Agreement, as well as the conditions of this Agreement
as has not yet entered the public domain, and shall not disclose or divulge the same to any third party
without approval of the Licensor.
Article 8
Termination
In case the User falls under any of the events described in the following items, the Licensor may
immediately terminate this Agreement or claim that the User compensates for the damage incurred by the
Licensor due to such event:
Article 3
Conditions for Grant of License
(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment, provisional attachment,
provisional disposition or any other compulsory execution.
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software
embedded in the Product (including any related materials, updates and upgrades) on condition that
no original, copies or related materials continue in the possession of the User, and that the User shall
cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code
analysis works in connection with the Licensed Software.
iii
Article 9
Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed
Software, any related documents and copies thereof within two (2) weeks from such date of termination.
Article 10
Protection of Copyright
1. The copyright and all the other intellectual property rights relating to the Licensed Software
shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the
ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the
copyright and other intellectual property rights.
Article 11
Export Restriction
1. It is prohibited to export the Licensed Software and any related documents outside the country
of the User (including transmission thereof outside the country of the User via Internet of other
communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions
adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and
domestic laws (including the export control regulation of the country of User and any other countries,
and any restrictions concerning the end-users, the use by end-users and importing countries to be
provided by the country of User and any other countries, and any other governmental authorities).
Article 12
Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions
shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of
this Agreement shall be provided or settled upon good-faith consultation between the Licensor and
the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and
any dispute arising from, and relating to the rights and obligations under, this Agreement shall be
submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.
iv
-CMP
Important Notice concerning the Software
-jansson
The MIT License (MIT)
Copyright (c) 2014 Charles Gunyon
Copyright (c) 2009-2012 Petri Lehtinen <petri@digip.org>
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/ or sell copies of
the Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Copyright (c) 2011 Petteri Aimonen <jpa at nanopb.mail.kapsi.fi>
-cJSON
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be
held liable for any damages arising from the use of this software.
Copyright (c) 2009 Dave Gamble
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/ or sell copies of
the Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
Permission is granted to anyone to use this software for any purpose, including commercial applications,
and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote
the original software. If you use this software in a product, an acknowledgment in the product
documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the
original software.
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
3. This notice may not be removed or altered from any source distribution.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
v
vi
Before Use................................................................................................. 3
Getting Started ........................................................................................ 5
Audio Settings........................................................................................ 29
Display Settings..................................................................................... 33
1
2
3
Select the display language and cancel the demonstration
Set the clock and date
Maintenance
HD RadioTM Tuner .................................................................................... 8
Radio........................................................................................................ 10
More information
Troubleshooting.................................................................................... 44
Specifications......................................................................................... 47
• The displays and faceplates shown in this manual are examples used to
provide clear explanations of the operations. For this reason, they may
be different from the actual displays or faceplates.
.
KENWOOD Remote application
• English indications are used for the purpose of explanation. You can
select the display language from the [FUNCTION] menu. (Page 7)
•
[XX] indicates the selected items.
• (Page XX) indicates references are available on the stated page.
Bluetooth – Connection
Bluetooth – Mobile phone
Bluetooth – Audio
This symbol on the product means there are important
operating and maintenance instructions in this manual.
Be sure to carefully read instructions in this manual.
AMAZON ALEXA .................................................................................... 28
2
ENGLISH
Before Use
IMPORTANT
• To ensure proper use, please read through this manual before using this
product. It is especially important that you read and observe Warnings and
Cautions in this manual.
• If a disc error occurs due to condensation on the laser lens, eject the disc
and wait for the moisture to evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate.
(Page 4)
• Depending on the types of cars, the antenna will automatically extend
when you turn on the unit with the antenna control wire connected
(page 38). Turn off the unit or change the source to STANDBY when
parking at a low ceiling area.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe
driving.
Remote control (RC-406):
• Do not ingest the battery, Chemical Burn Hazard.
The remote control supplied with this product contains a coin/button cell
battery.
If the coin/button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the
product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part
of the body, seek immediate medical attention.
• Do not leave the remote control in hot places such as on the dashboard.
• Risk of fire or explosion if the battery is replaced by an incorrect type.
Ensure to replace only with the same type.
• Risk of fire, explosion or the leakage of flammable liquid or gas if the
battery is left in an extremely high temperature surrounding environment
and/or subjected extremely low air pressure. The battery pack or batteries
shall not be exposed to excessive heat such as sunshine, fire or the like.
• Risk of fire, explosion or the leakage of flammable liquid or gas if the
battery is disposed into fire or a hot oven, recharged, shorted, mechanically
crushed or cut of the battery.
• If spilled fluid comes in contact with your eyes or on clothing, immediately
rinse with water and consult a physician.
CAUTION
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent
accidents.
• Lower the volume before playing digital sources to avoid damaging the
speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no
responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside
the unit to prevent a short circuit.
3
ENGLISH
Basics
Faceplate
Attach
Volume knob
Loading slot
Lights up when Bluetooth
connection is established.
(Page 22)
Detach
How to reset
Reset the unit within 5 seconds after
detaching the faceplate.
Detach button
Display window*1
To
On the faceplate
Turn on the power
Press BSRC.
• Press and hold to turn off the power.*2
Adjust the volume
Select a source
Turn the volume knob.
• Press BSRC repeatedly.
• Press BSRC, then turn the volume knob within 2 seconds.
Change the display information*3
Press DISP repeatedly. (Page 42, 43)
*1 Only for illustration purpose.
*2 For
*3 For
: The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off).
: You can also turn off the display information by pressing DISP repeatedly. (Page 43)
4
ENGLISH
Basics
Getting Started
Remote control (RC-406) (supplied for
)
Remote sensor (Do not expose to bright sunlight.)
Pull out the insulation sheet when
using for the first time.
1
Select the display language and cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to
[YES], see page 7), the display shows: “SEL LANGUAGE” “PRESS”
“VOLUME KNOB”
/
/
/
/
: Can be
remotely controlled with an optionally purchased remote control.
: Remote control functions are
not available.
/
/
1
Turn the volume knob to select [ENG] (English) / [SPA] (Spanish) /
[FRE] (French), then press the knob.
[ENG] is selected for the initial setup.
How to replace the battery
Then, (except for
) the display shows: “CANCEL DEMO”
“PRESS” “VOLUME KNOB”.
Press the volume knob again.
[YES] is selected for the initial setup.
Press the volume knob again.
“DEMO OFF” appears.
2
3
To
On the remote control
2
Set the clock and date
Adjust the volume
Press VOL or VOL
.
• Press and hold VOL to continuously increase
the volume to 15.
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select [CLOCK], then press the knob.
Press ATT during playback to attenuate the sound.
• Press again to cancel.
To adjust the clock
3
4
Turn the volume knob to select [CLOCK ADJUST], then press the knob.
Turn the volume knob to make the settings, then press the knob.
Set the time in the order of “Hour” “Minute”.
Select a source
Press SRC repeatedly.
Turn off the power
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
5
6
Turn the volume knob to select [CLOCK FORMAT], then press the knob.
Turn the volume knob to select [12H] or [24H], then press the knob.
5
ENGLISH
Getting Started
To set the date
[DISPLAY]
7
Turn the volume knob to select [DATE FORMAT], then press the knob.
Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press
the knob.
[EASY MENU]
(For
/
/
/
8
/
/
)
When entering [FUNCTION]...
[ON]: [ZONE 1] illumination changes to white color. ;
[OFF]: [ZONE 1] illumination remains as [COLOR SELECT] color.
(Page 33)
• [ZONE 2] illumination changes to light blue color when you enter
9
Turn the volume knob to select [DATE SET], then press the knob.
10 Turn the volume knob to make the settings, then press the knob.
Set the date in the order of “Day” “Month” “Year” or “Month” “Day”
“Year”.
11 Press and hold
to exit.
[FUNCTION], irregardless of the [EASY MENU] setting.
Refer to the illustration on page 33 for zone identification.
•
To return to the previous setting item, press
.
[TUNER SETTING]
[PRESET TYPE]
3
[NORMAL]: Memorizes one station for each preset button in each band
(FM1/FM2/FM3/AM). ; [MIX]: Memorizes one station or SiriusXM
channel for each preset button, regardless of the selected band or
SiriusXM channel.
Set the other optional settings
You can only set the following items while the unit is in STANDBY source.
1
2
3
Press BSRC repeatedly to enter STANDBY.
Press the volume knob to enter [FUNCTION]
Turn the volume knob to select an item (see the following table), then
press the knob.
Repeat step 3 until the desired item is selected or activated.
Press and hold
[SYSTEM]
.
[KEY BEEP]
[ON]: Activates the keypress tone. ; [OFF]: Deactivates.
[SOURCE SELECT]
[PANDORA SRC]
4
5
to exit.
[ON]: Enables PANDORA/PANDORA BT in source selection. ;
[OFF]: Disables. (Page 14)
To return to the previous setting item, press
.
[SPOTIFY SRC]
[BT AUDIO SRC]
[BUILT-IN AUX]
[ON]: Enables SPOTIFY/SPOTIFY BT in source selection. ;
[OFF]: Disables. (Page 15)
Default: [XX]
[AUDIO CONTROL]
[ON]: Enables BT AUDIO in source selection. ;
[OFF]: Disables. (Page 27)
[SWITCH PREOUT]
(For
/
/
)
[ON]: Enables AUX in source selection. ; [OFF]: Disables. (Page 20)
[REAR]/[SUB-W]: Selects whether rear speakers or a subwoofer are
connected to the line out terminals on the rear (through an external
amplifier). (Page 39)
6
ENGLISH
Getting Started
1
2
Turn the volume knob to select an item, then press the knob.
[SYSTEM] [REM SETTING] [REMOTE ID SET]
Remote control ID list is displayed.
[CD READ]
[1]: Automatically distinguishes between audio file disc and music CD. ;
[2]: Forces to play as a music CD. No sound can be heard if an audio file
disc is played.
•
•
[YES] indicates that this ID is already registered.
[NO] indicates that this ID is available.
[USER S.REMO]
[F/W UPDATE]
(For
)
See page 35 for details.
Turn the volume knob to select an available ID [REM ID1]
/[REM ID2]/
[REM ID3], then press the knob.
“REGISTERING” appears on the display window.
[UPDATE SYSTEM]/[UPDATE HD] (for
/
)
To register, on the KENWOOD Marine Remote Control unit:
• Press ENTER to register as [REM ID1]
• Press SRC to register as [REM ID2]
• Press DISP to register as [REM ID3]
Once the ID is registered, “COMPLETED” appears.
[F/W UP xxxx] [YES]: Starts upgrading the firmware. ; [NO]: Cancels (upgrading is not
activated).
.
.
For details on how to update the firmware, visit
<www.kenwood.com/cs/ce/>.
.
[FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ;
[NO]: Cancels.
To delete the registered ID
1
2
3
Turn the volume knob to select an item, then press the knob.
[SYSTEM] [REM SETTING] [REMOTE ID DEL]
Turn the volume knob to select the ID to delete [ID1 DELETE]/[ID2 DELETE]/
[ID3 DELETE], then press the knob.
Turn the volume knob to select [YES] to delete the selected ID, and
select [NO] to cancel.
[ENGLISH]
Select the display language for [FUNCTION] menu and music information
if applicable.
By default, [ENGLISH] is selected.
[ESPANOL]
[FRANCAIS]
Register the marine remote ID (for
)
• To exit, press and hold
• To return to the previous setting item, press
.
.
Applicable only when you connect KENWOOD Marine Remote Control unit
(KCA-RC55MR, optional accessory) to this unit.
• For connection, see “Connect external components” on page 39.
• Refer also to the supplied instruction manual of the KENWOOD Marine
Remote Control unit for more information.
Preparation:
Press BSRC repeatedly to enter STANDBY, then press the volume knob to
enter [FUNCTION]
.
7
ENGLISH
HD Radio™ Tuner(for
/
)
You can tune in to both conventional and HD Radio broadcasts.
Select an HD Radio multicast channel
• To find HD Radio stations in your area, visit <http://www.hdradio.com>.
Many HD Radio stations offer more than one channel programming. This
service is called multicasting.
While receiving HD Radio multicast channels....
Press S / T to select your desired channel (HD1 to HD8).
“LINKING” appears while linking to a multicast channel.
Receive an Emergency Alert message
Search for a station
You can receive an emergency alert message while listening to another
source or while in STANDBY, via HD Radio Broadcast.
1
2
Press BSRC repeatedly to select HD RADIO.
Press BAND repeatedly (or press #FM+/*AM– on the remote control)
to select FM1/FM2/FM3/AM.
Activate emergency alert message reception
3
Press S / T (or press S / T (+) on the remote control) to
1
2
3
4
5
Press the volume knob to enter [FUNCTION].
search for a station or channel.
Turn the volume knob to select [TUNER SETTING], then press the knob.
Turn the volume knob to select [EA], then press the knob.
Turn the volume knob to select [ON], then press the knob.
You can store up to 18 stations/channels for FM and 6 stations/channels for
AM.
• To store a station or channel: Press and hold one of the number buttons
Press and hold
to exit.
• To deactivate emergency alert message reception, select [OFF] in step 4.
• To return to the previous setting item, press
(1 to 6).
.
• To select a stored station or channel: Press one of the number buttons
(1 to 6) (or press one of the number buttons (1 to 6) on the remote
control).
Receive an emergency alert message
When an emergency alert message is received, it appears and remains on
the display until the user performs the “Ignore” function.
Direct Access Tuning (using the remote control)
Press BSRC (or press SRC on the remote control) to ignore the alert
message.
The same emergency alert message will not interrupt again for 12 hours.
1
2
Press DIRECT to enter Direct Access Tuning.
Press the number buttons to enter a station frequency or channel
number.
3
Press ENT IW to search for station or channel.
• To cancel, press or DIRECT.
• If no operation is done for 10 seconds after step 2, Direct Access Tuning is
automatically canceled.
8
ENGLISH
HD Radio™ Tuner (for
/
)
Default: [XX]
Display received emergency alert messages
[TUNER SETTING]
[SEEK MODE]
The received emergency alert messages are stored in the Alert Message List,
and you can check them later.
While listening to the HD RADIO source...
Selects the searching method for
S
/
T
buttons when pressed.
[AUTO1]: Automatically search for a station or channel. ;
[AUTO2]: Search for a preset station or channel. ;
[MANUAL]: Manually search for a station or channel.
1
2
3
Press
to display the Alert Message List.
Turn the volume knob to select a message.
Press the volume knob to display the information related to the
message.
[IF BAND]
[AUTO]: Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.) ;
[WIDE]: Subjects to interference noises from adjacent FM stations, but
4
Press
again to exit.
sound quality will not be degraded and the stereo effect will remain.
• “NO LIST” appears when the list is empty.
• This feature can store up to four messages in the list.
• To clear the message list, set [FACTORY RESET] to [YES]. (Page 7)
[AUTO MEMORY] [YES]: Automatically starts memorizing 6 stations with good reception. ;
[NO]: Cancels.
•
Selectable only if [NORMAL] is selected for [PRESET TYPE]. (Page 6)
[RECEIVE MODE] Sets the receive mode of the HD Radio receiver.
[AUTO]: Automatically tunes to analog broadcast when there is no digital
Other settings
broadcast. ;
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
[DIGITAL]: Tunes in to digital broadcast only. ;
[ANALOG]: Tunes in to analog broadcast only.
[CLOCK]
3
4
[TIME SYNC]
[ON]: Synchronizes the unit’s time to the Radio Broadcast Data System
station time. ; [OFF]: Cancels.
Press and hold
to exit.
To return to the previous setting item, press
.
9
ENGLISH
Radio(for
/
/
/
/
/
/
)
Other settings
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
3
4
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
Press and hold
to exit.
• “ST” indicator lights up when receiving an FM stereo broadcast with
sufficient signal strength.
• The unit switches to FM alarm automatically when receiving an alarm
signal from FM broadcast.
To return to the previous setting item, press
.
Default: [XX]
[TUNER SETTING]
Search for a station
[SEEK MODE]
Selects the searching method for
[AUTO1]: Automatically search for a station. ; [AUTO2]: Search for a preset
station. ; [MANUAL]: Manually search for a station.
S
/
T buttons when pressed.
1
2
Press BSRC repeatedly to select RADIO.
Press BAND repeatedly (or press #FM+/ AM– on the remote control)
to select FM1/FM2/FM3/AM.
Press S / T (or press S / T (+) on the remote control) to
search for a station.
*
[AUTO MEMORY] [YES]: Automatically starts memorizing 6 stations with good reception. ;
3
[NO]: Cancels.
•
Selectable only if [NORMAL] is selected for [PRESET TYPE]. (Page 6)
[MONO SET]
[NEWS SET]
[ON]: Improves the FM reception, but the stereo effect will be lost. ;
[OFF]: Cancels.
You can store up to 18 stations for FM and 6 stations for AM.
• To store a station: Press and hold one of the number buttons (1 to 6).
• To select a stored station: Press one of the number buttons (1 to 6) (or
press one of the number buttons (1 to 6) on the remote control).
(For
)
[ON]: The unit will temporarily switch to News Programme if available. ;
[OFF]: Cancels.
Direct Access Tuning (using the remote control)
[REGIONAL]
[AF SET]
(For
)
[ON]: Switches to another station only in the specific region using the “AF”
control. ; [OFF]: Cancels.
1
2
3
Press DIRECT to enter Direct Access Tuning.
Press the number buttons to enter a station frequency.
Press ENT IW to search for a station.
(For
)
[ON]: Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor. ; [OFF]: Cancels.
• To cancel, press or DIRECT.
• If no operation is done for 10 seconds after step 2, Direct Access Tuning is
automatically canceled.
10
ENGLISH
(for
/
/
/
/
Radio
/
/
)
CD/USB/iPod
[TI]
[ON]: Allows the unit to temporarily switch to Traffic Information if
available (“TI” indicator lights up). ; [OFF]: Cancels.
Insert a disc
Eject disc
Label side
[PTY SEARCH]
(For
/
/
/
/
/
)
Select the available Program Type (for Radio Broadcast Data System, see
page 41), then press
(For
S
/
T
to start.
)
The source changes to CD automatically and playback starts.
1
2
3
Turn the volume knob to select the available Program Type (for Radio
Data System, see page 41), then press the knob.
Turn the volume knob to select the PTY language ([ENGLISH]/
[FRENCH]/[GERMAN]), then press the knob.
Connect a USB device
USB input terminal
CA-U1EX (max.: 500 mA)
Press
S
/
T
to start searching.
(optional accessory)*1
[CLOCK]
USB device
[TIME SYNC]
[ON]: Synchronizes the unit’s time to the Radio Broadcast Data System/
Radio Data System station time. ; [OFF]: Cancels.
•
[MONO SET]
when the band is FM1/FM2/FM3.
/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH] is selectable only
The source changes to USB automatically and playback starts.
• If the volume is adjusted during reception of traffic information or news
bulletin, the adjusted volume is memorized automatically. It will be applied
the next time traffic information or news bulletin is turned on.
Connect an iPod/iPhone
iPod/iPhone
USB input terminal
KCA-iP103 (optional accessory)*2
or accessory of the iPod/iPhone*1
The source changes to iPod USB automatically and playback starts.
• You can also connect iPod/iPhone via Bluetooth. (Page 22)
*1 Do not leave the cable inside the car when not in use.
*2 KCA-iP103: Lightning type
11
ENGLISH
CD/USB/iPod
Select music drive
While in USB source, press 5 repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drive device.
To
On the faceplate
On the remote control
You can also select the music drive from the [FUNCTION] menu.
Play back/pause
Press 6 IW.
Press ENT IW.
1
2
3
4
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select [USB], then press the knob.
Turn the volume knob to select [MUSIC DRIVE], then press the knob.
Turn the volume knob to select [DRIVE CHANGE], then press the knob.
The next drive ([DRIVE 1] to [DRIVE 4]) is selected automatically and
playback starts.
Reverse/Fast-forward Press and hold
Press and hold
S / T (+).
S / T.
Select a track/file
Select a folder*1
Repeat play*2
Press S / T.
Press 2 / 1
Press 4 repeatedly.
[TRACK REPEAT] [ALL REPEAT]: Audio CD
[FILE REPEAT] [FOLDER REPEAT] [ALL REPEAT]: MP3/
WMA/AAC/WAV/FLAC file
[REPEAT ONE] [REPEAT ALL] [REPEAT OFF]: iPod
Press 3 repeatedly.
[DISC RANDOM] [RANDOM OFF]: Audio CD
Press S / T (+).
.
Press #FM+/ AM–.
5
6
Repeat step 1 to step 4 to select the following drives.
Press and hold
to exit.
/
To return to the previous setting item, press
.
/
/
/
/
Select control mode
Random play*2
While in iPod USB source (or iPod BT source), press 5 repeatedly.
[MODE ON]
/
:
Control iPod/iPhone using the iPod/iPhone itself. However, you
can still perform play/pause, file skip, fast-forward or fast-reverse
from this unit.
[FOLDER RANDOM]/[RANDOM OFF]: MP3/WMA/AAC/
WAV/FLAC file
[SHUFFLE ON]/[SHUFFLE OFF]: iPod
[MODE OFF]: Control iPod/iPhone from this unit.
Press and hold 3 to select [ALL RANDOM].*1
Direct Music Search (using the remote control)
*1 For CD: Only for MP3/WMA/AAC files. This does not work for iPod.
*2 For iPod: Applicable only when [MODE OFF] is selected.
1
2
3
Press DIRECT.
Press the number buttons to enter a track/file number.
Press ENT IW to search for music.
12
ENGLISH
CD/USB/iPod
• To cancel, press or DIRECT.
[SKIP SEARCH] setting
• Not available if Random Play is selected.
• Not applicable for iPod USB source.
1
2
3
4
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select [USB], then press the knob.
Turn the volume knob to select [SKIP SEARCH], then press the knob.
Turn the volume knob to select the skip search ratio, then press the
knob.
Select a file to play
From a folder or list
[0.5%] (default)/[1%]
The skip search ratio is shown as a percentage of the total files.
Press and hold to exit.
/[5%]/[10%]
• For iPod, applicable only when [MODE OFF] is selected. (Page 12)
5
1
2
3
Press
.
Turn the volume knob to select a folder/list, then press the knob.
Turn the volume knob to select a file, then press the knob.
Selected file starts playing.
Alphabet search (applicable only for iPod USB source and iPod BT source)
You can search for a file according to the first character.
• For iPod, applicable only when [MODE OFF] is selected. (Page 12)
Quick search (applicable only for CD source and USB source)
1
2
3
4
Press
.
Turn the volume knob to select a list, then press the knob.
Turn the volume knob quickly to enter character search.
Turn the volume knob to select the character.
• Select “ ” to search for a character other than A to Z, 0 to 9.
Press S / T to move to the entry position.
• You can enter up to 3 characters.
Press the volume knob to start searching.
Turn the volume knob to select a file, then press the knob.
Selected file starts playing.
If you have many files, you can search through them quickly.
1
2
3
4
Press
.
Turn the volume knob to select a folder/list, then press the knob.
Turn the volume knob quickly to browse through the list quickly.
Turn the volume knob to select a file, then press the knob.
Selected file starts playing.
*
5
6
7
Skip search (applicable only for iPod USB source and iPod BT source)
If you have many files in the selected list, you can perform the following to
search for a file by skipping through the list at a rate selected in [SKIP SEARCH]
• For iPod, applicable only when [MODE OFF] is selected. (Page 12)
• To return to the root folder/first file/top menu, press 5. (Not applicable for
BT AUDIO source.)
.
• To return to the previous setting item, press
• To cancel, press and hold
.
1
2
3
Press
.
.
Turn the volume knob to select a list, then press the knob.
Press S / T to search at a preset skip search ratio.
• Pressing and holding S / T searches at a 10% ratio irregardless of
the [SKIP SEARCH] settings.
4
Turn the volume knob to select a file, then press the knob.
Selected file starts playing.
13
ENGLISH
Pandora®(for
/
/
/
/
/
/
/
)
You can listen to Pandora on iPhone/iPod touch (via Bluetooth or via USB
input terminal) or Android device (via Bluetooth).
To
On the faceplate
Press 6 IW.
Press T.
On the remote control
Play back/pause
Skip a track
Press ENT IW.
Press T (+).
Preparation:
• Install the latest version of the Pandora application on your device (iPhone/
iPod touch or Android device), then create an account and log in to
Pandora.
Select thumbs up or
thumbs down*3
Press 2 / 1
.
Press #FM+/ AM–.
• Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 6)
*1 KCA-iP103: Lightning type
*2 Do not leave the cable inside the car when not in use.
*3 If thumbs down is selected, the current track is skipped.
Start listening
1
2
Start up the Pandora application on your device.
Connect your device to the USB input terminal.
Create and store a new station
USB input terminal
iPhone/
iPod touch
KCA-iP103 (optional accessory)*1 or
1
2
3
Press
.
accessory of the iPhone/iPod touch*2
Turn the volume knob to select [NEW STATION], then press the knob.
Turn the volume knob to select [FROM ARTIST] or [FROM TRACK], then
press the knob.
A new station is created based on the current artist or current song.
4
Press and hold one of the number buttons (3, 4 or 5) to store.
To select a stored station: Press one of the number buttons (3, 4 or 5).
You can also connect the iPhone/iPod touch or Android device via
Bluetooth. (Page 22)
• Make sure the USB input terminal is not connected to any device when
you connect via Bluetooth.
Press BSRC repeatedly to select PANDORA (for iPhone/iPod touch) or
PANDORA BT (for Android device).
Search for a registered station
1
2
Press
.
3
Turn the volume knob to select an item, then press the knob.
[SORT BY DATE]: According to the registered date
Broadcast starts automatically.
[SORT BY A-Z]
:
By alphabetical order
3
4
Turn the volume knob (or press J / K on the remote control) to select
the desired station.
Press the volume knob (or press ENT IW on the remote control) to
confirm.
To cancel, press and hold
.
14
ENGLISH
(for
/
/
/
/
Pandora®
/
/
/
)
Spotify
You can listen to Spotify on iPhone/iPod touch (via Bluetooth or via USB
input terminal) or Android device (via Bluetooth).
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
Preparation:
• Install the latest version of the Spotify application on your device (iPhone/
iPod touch or Android device), then create an account and log in to
Spotify.
• The bookmark is available on your Pandora account but not on this unit.
Delete a station
• Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. (Page 6)
While listening to PANDORA...
Start listening
1
2
3
Press
.
Turn the volume knob to select [STATION DEL], then press the knob.
Turn the volume knob to select [SORT BY DATE] or [SORT BY A-Z], then
press the knob.
Turn the volume knob to select the desired station to delete, then
press the knob.
Turn the volume knob to select [YES], then press the knob.
Press and hold
1
2
Start up the Spotify application on your device.
Connect your device to the USB input terminal.
USB input terminal
iPhone/
iPod touch
4
KCA-iP103 (optional accessory)*1 or
accessory of the iPhone/iPod touch*2
5
6
to exit.
To return to the previous setting item, press
.
You can also connect the iPhone/iPod touch or Android device via
Bluetooth. (Page 22)
• Make sure the USB input terminal is not connected to any device when
you connect via Bluetooth.
3
Press BSRC repeatedly to select SPOTIFY (for iPhone/iPod touch) or
SPOTIFY BT (for Android device).
Broadcast starts automatically.
15
ENGLISH
Spotify
To
On the faceplate
Press 6 IW.
On the remote control
Press ENT IW.
Search for a song or station
Press
Turn the volume knob to select a list type, then press the knob.
The list types displayed differ depending on the information sent from
Spotify.
Play back/pause
Skip a track
1
2
.
Press S*3 / T.
Press S*3 / T (+).
Press #FM+/ AM–.
Select thumbs up or
thumbs down*4
Press 2 / 1
.
3
4
Turn the volume knob (or press J / K on the remote control) to select
Start radio
Press and hold 5.
( Not available )
( Not available )
the desired song or station.
Press the volume knob (or press ENT IW on the remote control) to
confirm.
Repeat play*5
Press 4 repeatedly.
[REPEAT ALL]
,
[REPEAT ONE]*3,
You can browse through the list quickly by turning the volume knob
quickly.
[REPEAT OFF]
Random play*5
Press 3 repeatedly*3.
[SHUFFLE ON] [SHUFFLE OFF]
( Not available )
To cancel, press and hold
.
,
*1 KCA-iP103: Lightning type
*2 Do not leave the cable inside the car when not in use.
*3 Available for premium account users only.
*4 This feature is available for tracks in Radio only. If thumbs down is selected, the current track is
skipped.
*5 Available for tracks in Playlists only.
Save favorite song information
While listening to the Radio on Spotify...
Press and hold the volume knob.
“SAVED” appears and the information is stored to “Your Music” or “Your
Library” on your Spotify account.
To unsave, repeat the same procedure.
“REMOVED” appears and the information is removed from “Your Music” or
“Your Library” on your Spotify account.
16
ENGLISH
SiriusXM® Radio(for
/
/
/
/
/
)
Only SiriusXM® brings you more of what you love to listen to, all in one place.
Get over 140 channels, including commercial-free music plus the best sports,
news, talk, comedy and entertainment. Welcome to the world of satellite
radio. A SiriusXM Vehicle Tuner and Subscription are required. For more
information, visit <www.siriusxm.com>.
Start listening
1
2
3
Press BSRC repeatedly to select SIRIUS XM.
Press BAND repeatedly to select a band.
Press
.
“
” indicator lights up.
Preparation:
4
5
Turn the volume knob to select a category, then press the knob.
If “ALL CHANNELS” is selected, all the available channels will be shown.
Turn the volume knob to select a channel, then press the knob.
(or)
1
Connect the optional SiriusXM Vehicle Tuner (commercially available).
Antenna
Press S / T to search for a channel manually.
• Pressing and holding S / T changes the channel rapidly.
SiriusXM Vehicle Tuner
Expansion port on
the rear panel
If a locked channel or a mature channel is selected, a pass code input
screen appears. Enter the pass code to receive the channel. (Page 19)
2
3
Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and can be found by
tuning to Channel 0 as well as on the label found on the SiriusXM Vehicle
Tuner and its packaging.
The Radio ID does not include the letters I, O, S or F.
Activate the subscription.
Direct Access Tuning (using the remote control)
1
Press DIRECT to enter Direct Access Tuning.
Press the number buttons to enter a channel number.
Press ENT IW to search for the channel.
2
3
For users in the U.S.A.:
Online: Go to <www.siriusxm.com>
Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to <www.siriusxm.ca/subscribe-now>
Phone: Call 1-877-438-9677
• To cancel, press or DIRECT.
• If no operation is done for 10 seconds after step 2, Direct Access Tuning is
automatically canceled.
4
Press BSRC repeatedly to select SIRIUS XM to start updating.
17
ENGLISH
SiriusXM® Radio (for
/
/
/
/
/
)
SiriusXM Keymode
SmartFavorites and TuneStart™
User stored channels are recognized as SmartFavorite channels*. The
SiriusXM Vehicle Tuner automatically buffers the broadcast content in the
background.
• SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle
Tuner.
* SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites.
The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as
SmartFavorites.
Press and hold the volume knob to change the keymode (channel or
replay). (Default: Channel keymode)
“
” indicator lights up when replay keymode is selected.
When channel keymode is selected...
To
On the faceplate
On the remote control
Select a channel
Press S / T.
Press S / T (+).
Change a channel
rapidly
Press and hold S /
Press and hold S /
When you select a SmartFavorite channel, you can rewind and replay up to
30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if [TUNE START] is set to [ON]
(page 19) for most music channels stored as a SmartFavorite.
T.
T (+).
Store a channel of
the current band
Press and hold one of the
number buttons (1 to 6).
( Not available )
Select a stored
channel of the
current band
Press one of the number Press one of the number
Press one of the number buttons (1 to 6) to select a stored channel.
buttons (1 to 6).
buttons (1 to 6).
TuneScan™
When replay keymode is selected...
You can get a short preview of the songs that you have missed on each of
your SmartFavorites music channels or a music channel currently tuned into.
To
On the faceplate
On the remote control
Press ENT IW.
Play back/pause
Press 6 IW.
Press and hold BAND to start scanning the first 6 seconds of the recorded
music contents.
Skip backward/
forward
Press S / T.
Press S / T (+).
• To listen to the current song, press the volume knob to stop scanning. The
unit continues playing the current song.
• To select the previous/next song, press S / T.
• To cancel scanning, press and hold the volume knob. Playback returns to
the channel before you entered TuneScan.
Rewind/Fast-forward
Press and hold S /
T.
Press and hold S /
T (+).
Go to Live
Press 1.
Press 1.
18
ENGLISH
SiriusXM® Radio (for
/
/
/
/
/
)
[LOCK SETTING]
[MATURE CH]: Selects the SiriusXM-defined lock setting. ;
[USER DEFINED]: Selects the individual channels the user wants to
lock. ; [OFF]: Cancels.
SiriusXM settings
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
[CHANNEL EDIT]*1
1
2
Turn the volume knob to select a category, then press the knob.
Turn the volume knob to select a channel you want to lock, then
press the knob.
3
4
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
Press and hold
“L” appears in front of the channel number.
to exit.
3
Press and hold
to exit.
To return to the previous setting item, press
.
[CHANNEL CLEAR]*1 [YES]: Clears all the locked channels. ; [NO]: Cancels.
Default: [XX]
[TUNE START]*2
[ON]: All qualified music channels in the SmartFavorites will start
playback from the beginning of the song. ; [OFF]: Cancels.
[SIRIUS XM]
[SIGNAL LEVEL]
Shows the strength ([NO SIGNAL]/[WEAK]/[GOOD]/[STRONG]) of
the current received signal.
[SEEK MODE]
Selects the tuning method for
[CHANNEL]: Manually search for a channel. ; [PRESET]: Search for a preset
S
/
T buttons when pressed.
channel of the selected band.
[BUFFER USAGE]
[SXM RESET]
Shows the memory usage ([0%] to [100%]) for Replay buffer.
[CHANNEL LOCK] To unlock settings:
[YES]: Resets all SiriusXM settings to default. ; [NO]: Cancels.
1
2
3
Turn the volume knob to select a number.
Press to move to the entry position.
Repeat step 1 and step 2 to enter the current pass code.
(Initial pass code is 0000.)
S
/
T
*1 Displayed only when [LOCK SETTING] is set to [USER DEFINED].
*2 Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later which supports
SmartFavorites.
4
Press the volume knob to confirm.
[CODE SET]
1
2
3
4
5
•
Turn the volume knob to select a number.
Press
S
/
T
to move to the entry position.
Repeat step 1 and step 2 to enter a new 4-digit pass code.
Press the volume knob to confirm.
Repeat step 1 to step 4 to reconfirm the pass code.
Make a note of the new pass code to enter channel lock settings for next
time.
19
ENGLISH
AUX
Using Other Applications
KENWOOD Remote application
You can listen to music from a portable audio player via the auxiliary input
jack.
You can control the KENWOOD car receiver from iPhone/iPod touch (via
Bluetooth or via USB input terminal) or Android device (via Bluetooth) using
KENWOOD Remote application.
Preparation:
Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 6)
• For more information, visit <http://www.kenwood.com/cs/ce/>.
Preparation:
Start listening
Install the latest version of KENWOOD Remote application on your device
before connecting.
1
Connect a portable audio player (commercially available).
Auxiliary input jack
Portable audio player
Start using KENWOOD Remote application
1
2
Start up the KENWOOD Remote application on your device.
Connect your device.
• For Android device:
Pair the Android device with this unit via Bluetooth. (Page 22)
• For iPhone/iPod touch:
Connect iPhone/iPod touch to the USB input terminal. (Page 11)
(or)
Pair the iPhone/iPod touch with this unit via Bluetooth. (Page 22)
(Make sure the USB input terminal is not connected to any device.)
Select the device to use from the [FUNCTION] menu.
See “Settings to use KENWOOD Remote application” on page 21.
By default, [ANDROID] is selected. To use iPhone/iPod touch, select [YES] for
3.5 mm (1/8") stereo mini plug with “L”
shaped connector (commercially available)
2
3
Press BSRC repeatedly to select AUX.
Turn on the portable audio player and start playback.
3
Set the name of the external device
While listening to a portable audio player connected to the unit...
[IOS]
.
1
2
3
4
Press the volume knob to enter [FUNCTION].
• For
/
/
/
/
/
Turn the volume knob to select [SYSTEM], then press the knob.
Turn the volume knob to select [AUX NAME SET], then press the knob.
Turn the volume knob to select an item, then press the knob.
, “R.APP” indicator lights up when KENWOOD Remote
application is connected.
[AUX] (default)/[DVD]
/
[PORTABLE]/[GAME]
/
[VIDEO]/[TV]
5
Press and hold
to exit.
To return to the previous setting item, press
.
20
ENGLISH
Using Other Applications
[STATUS]
Shows the status of the selected device.
Settings to use KENWOOD Remote application
[IOS CONNECTED]: You are able to use the application using the iPhone/
iPod touch connected via Bluetooth or USB input terminal.
[IOS NOT CONNECTED]: No iOS device is connected to use the application.
[ANDROID CONNECTED]: You are able to use the application using the
Android device connected via Bluetooth.
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
3
4
Repeat step 2 until the desired item is selected/activated.
Press and hold
to exit.
[ANDROID NOT CONNECTED]: No Android device is connected to use the
application.
To return to the previous setting item, press
.
Default: [XX]
Tuneln Radio/Tuneln Radio Pro
[REMOTE APP]
While listening to TuneIn Radio or TuneIn Radio Pro, connect the iPhone/
iPod touch to the USB input terminal of the unit so that the unit will output
the sound from these applications.
[SELECT]
[IOS]
Selects the device ([IOS] or [ANDROID]) to use the application.
[YES]: Selects iPhone/iPod touch to use the application via Bluetooth or
connected via USB input terminal. ; [NO]: Cancels.
If [IOS] is selected, select iPod BT source (or iPod USB source if your iPhone/
iPod touch is connected via USB input terminal) to activate the application.
•
The connectivity of the application will be interrupted or disconnected if:
– You change from iPod BT source to any playback source connected via
the USB input terminal.
– You change from iPod USB source to iPod BT source.
[ANDROID]
[YES]: Selects Android device to use the application via Bluetooth. ;
[NO]: Cancels.
[ANDROID LIST] Selects the Android device to use from the list.
Displayed only when [ANDROID] of [SELECT] is set to [YES].
•
21
ENGLISH
Bluetooth®
• Depending on the Bluetooth version, operating system and the firmware
version of your mobile phone, Bluetooth features may not work with this
unit.
• Be sure to turn on the Bluetooth function of the device to make the
following operations.
Pair and connect a Bluetooth device for the first time
1
2
Press BSRC to turn on the unit.
Search and select the name of your receiver (“KDC-X704”/
“KDC-X304”/“KDC-BT778HD”/“KDC-BT378U”/“KDC-BT360U”/
“KDC-BT34”/“KDC-BT278U”/“KDC-MP378BT”/“KMR-D378BT”) on the
Bluetooth device.
• Signal conditions vary depending on the surroundings.
“PAIRING” “PASS XXXXXX” “Device name” “PRESS” “VOLUME
KNOB” appears on the display.
• For some Bluetooth devices, you may need to enter the Personal
Identification Number (PIN) code immediately after searching.
Press the volume knob to start pairing.
Bluetooth — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
3
“PAIRING OK” appears when pairing is completed.
– Phonebook Access Profile (PBAP)
Once pairing is completed, Bluetooth connection is established
automatically.
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
•
/
/
/
/
/
: “BT1” and/or “BT2” indicator on the faceplate lights up.
” indicator lights up to show the strength of the battery and signal of
“
the connected device.
/
Connect the microphone
•
/
: “BT1” and/or “BT2” indicator
on the display window lights up.
Rear panel
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered
in the unit even if you reset the unit. To delete the paired device, see
[DEVICE DELETE] on page 26.
Microphone
(supplied)
Secure using cord
clamps (not supplied)
if necessary.
Microphone
input jack
• A maximum of two Bluetooth phones and one Bluetooth audio device can
be connected at any time. To connect or disconnect the registered device,
see [PHONE SELECT] or [AUDIO SELECT] in [BT MODE]. (Page 26)
Adjust the
microphone angle
However, while in BT AUDIO source, you can connect to five Bluetooth
audio devices and switch between these five devices. (Page 27)
• Some Bluetooth devices may not automatically connect to the unit after
pairing. Connect the device to the unit manually.
22
ENGLISH
Bluetooth®
• Refer to the instruction manual of the Bluetooth device for more
information.
The following operations may differ or be unavailable depending on the
connected phone.
To
On the faceplate
On the remote control
Auto Pairing
First incoming call...
Answer a call
When you connect iPhone/iPod touch to the USB input terminal, pairing
request (via Bluetooth) is automatically activated if [AUTO PAIRING] is set to
[ON]. (Page 26)
Press or the
Press
.
volume knob or
one of the number
buttons (1 to 6).
Press the volume knob to pair once you have confirmed the device name.
Reject a call
End a call
Press
Press
.
.
Press
Press
.
.
Bluetooth — Mobile phone
While talking on the first incoming call...
Answer another
incoming call and hold
the current call
Press
.
Press
Press
.
Reject another incoming
call
.
.
Press
.
.
While having two active calls...
Receive a call
End current call and
activate held call
Press
Press
Press
Press
When there is an incoming call:
•
/
/
/
/
/
Swap between the
current call and held call
.
.
:
[ZONE 2] illuminates in green color and flashes.
• The unit answers the call automatically if [AUTO ANSWER] is set to a selected
time. (Page 24)
Adjust the phone
volume*1
[00] to [35] (Default: [15]
Turn the volume
knob during a call.
Press VOL *2 or
VOL during a call.
)
During a call:
Switch between hands-
free and private talk
modes*3
( Not available )
Press 6 IW during
a call.
•
/
/
/
/
/
:
[ZONE 1] illuminates according to the settings made for [DISPLAY]
(page 33) and [ZONE 2] illuminates in green color.
• If you turn off the unit or detach the faceplate, Bluetooth is disconnected.
*1, *2, *3: See page 24.
23
ENGLISH
Bluetooth®
*1 This adjustment will not affect the volume of the other sources.
*2 Press and hold VOL to continuously increase the volume to 15.
*3 Operations may vary according to the connected Bluetooth device.
Make a call
You can make a call from the call history, phonebook, or dialing the number.
Call by voice is also possible if your mobile phone has the feature.
Improve the voice quality
1
Press to enter Bluetooth mode.
“(First device name)” appears.
While talking on the phone...
• If two Bluetooth phones are connected, press again to switch to the
other phone.
“(Second device name)” appears.
Turn the volume knob to select an item (see the following table), then
press the knob.
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
2
3
4
3
4
Repeat step 2 until the desired item is selected or activated.
Press and hold
to exit.
To return to the previous setting item, press
.
Press and hold
to exit.
Default: [XX]
To return to the previous setting item, press
.
[MIC GAIN]
[LEVEL –10] to [LEVEL +10] ([LEVEL –4]): The sensitivity of the
microphone increases as the number increases.
[CALL HISTORY] (Applicable only if the phone supports PBAP.)
[NR LEVEL]
[LEVEL –5] to [LEVEL +5] ([LEVEL 0]): Adjust the noise reduction level
until the least noise is being heard during a phone conversation.
1
2
Press the volume knob to select a name or a phone number.
•
“I” indicates call received, “O“ indicates call made, “M” indicates call
missed.
[ECHO CANCEL]
[LEVEL –5] to [LEVEL +5] ([LEVEL 0]): Adjust the echo cancellation
delay time until the least echo is being heard during a phone conversation.
•
•
Press DISP to change the display category (NUMBER or NAME).
“NO DATA” appears if there is no recorded call history or call number.
Press the volume knob to call.
Make the setting for answering a call
1
2
3
4
Press to enter Bluetooth mode.
Turn the volume knob to select [SETTINGS], then press the knob.
Turn the volume knob to select [AUTO ANSWER], then press the knob.
Turn the volume knob to select the time (in seconds) for the unit to
answer the call automatically, then press the knob.
[01] to [30], or select [OFF] to cancels. (Default: [OFF]
)
5
Press and hold to exit.
To return to the previous setting item, press
.
24
ENGLISH
Bluetooth®
Make a call using voice recognition
[PHONE BOOK] (Applicable only if the phone supports PBAP.)
1
Turn the volume knob quickly to enter alphabet search mode (if the
phonebook contains many contacts).
The first menu (ABCDEFGHIJK) appears.
1
2
Press and hold to activate the voice recognition of the connected
phone.
Speak the name of the contact you want to call or the voice command
to control the phone functions.
•
To go to the other menu (LMNOPQRSTUV or WXYZ1 ), press 2
/
1
.
•
To select the desired first letter, turn the volume knob or press
, then press the knob.
Select “1” to search with numbers and select “ ” to search with symbols.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
S
/
T
2
3
Turn the volume knob to select a name, then press the knob.
Turn the volume knob to select a phone number, then press the knob to
call.
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
•
For using phonebook with this unit, make sure to allow access to or transfer
from your smartphone. Depending on the connected phone, the process
may be different.
Contacts are categorized as: HM (home), OF (office), MO (mobile),
OT (other), GE (general)
1
2
Press to enter Bluetooth mode.
Turn the volume knob to select [CALL HISTORY]
[NUMBER DIAL], then press the knob.
Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
Press and hold one of the number buttons (1 to 6).
“STORED” appears when the contact is stored.
,
[PHONE BOOK] or
•
•
3
This unit can display only non-accent letters. (Accent letters such as “Ú” are
shown as “U”.)
4
[NUMBER DIAL]
1
2
Turn the volume knob to select a number (0 to 9) or character ( , #, +).
Press
S
/
T
to move the entry position.
To erase a contact from the preset memory, select [NUMBER DIAL] in step 2,
store a blank number in step 3 and proceed to step 4.
Repeat step 1 and step 2 until you finish entering the phone number.
Press the volume knob to call.
3
(or using the remote control)
Make a call to a registered number
1
2
Press the number buttons (0 to 9) to enter the phone number.
Press to call.
1
2
3
Press to enter Bluetooth mode.
Press one of the number buttons (1 to 6).
Press the volume knob to call.
[VOICE]
Speak the name of the contact you want to call or the voice command to
control the phone functions. (See also the following “Make a call using voice
recognition”.)
“NO MEMORY” appears if there is no contact stored.
[LOW]/[MID]/[FULL]: Shows the strength of the battery.*
[NO SIGNAL]/[LOW]/[MID]/[MAX]: Shows the strength of the current received signal.*
* Functionality depends on the type of the phone used.
25
ENGLISH
Bluetooth®
[INITIALIZE]
[YES]: Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.). ; [NO]: Cancels.
Bluetooth mode settings
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
Bluetooth test mode
3
4
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
Press and hold
to exit.
To return to the previous setting item, press
.
1
2
Press and hold
.
“PLEASE PAIR YOUR PHONE PIN 0000” appears on the display.
Search and select the name of your receiver (“KDC-X704”/
“KDC-X304”/“KDC-BT778HD”/“KDC-BT378U”/“KDC-BT360U”/
“KDC-BT34”/“KDC-BT278U”/“KDC-MP378BT”/“KMR-D378BT”) on the
Bluetooth device.
Default: [XX]
[BT MODE]
[PHONE SELECT]
Selects the phone or audio device to connect or disconnect.
“
“
•
” appears in front of the device name when connected.
” appears in front of the current playback audio device.
You can connect a maximum of two Bluetooth phones and one
Bluetooth audio device at a time.
3
Operate the Bluetooth device to confirm pairing.
“TESTING” flashes on the display.
[AUDIO SELECT]
The connectivity result (OK or NG) appears after the test.
PAIRING: Pairing status
HF CNT: Hands-Free Profile (HFP) compatibility
AUD CNT: Advanced Audio Distribution Profile (A2DP) compatibility
[DEVICE DELETE]
1
2
Turn the volume knob to select a device to delete, then press the
knob.
Turn the volume knob to select [YES] or [NO], then press the knob.
[PIN CODE EDIT]
(0000)
Changes the PIN code (up to 6 digits).
1
2
PB DL:
Phonebook Access profile (PBAP) compatibility
Turn the volume knob to select a number.
Press to move the entry position.
S
/
T
To cancel test mode, press and hold BSRC to turn off the unit.
Repeat step 1 and step 2 until you finish entering the PIN code.
Press the volume knob to confirm.
3
[RECONNECT]
[ON]: The unit is automatically reconnect when the last connected
Bluetooth device is within the connectable range. ; [OFF]: Cancels.
[AUTO PAIRING]
[ON]: The unit is automatically paired with the supported Bluetooth
device (iPhone/iPod touch) when it is connected through USB input
terminal. Depending on the operating system of the connected device,
this function may not work. ; [OFF]: Cancels.
26
ENGLISH
Bluetooth®
Bluetooth — Audio
To
On the faceplate
Repeat play
Press 4 repeatedly.
[ALL REPEAT]
,
[FILE REPEAT], [GROUP REPEAT]*,
[REPEAT OFF]
Random play
Press and hold 3 to select [ALL RANDOM]
or [GROUP RANDOM]*.
While in BT AUDIO source, you can connect to five Bluetooth audio devices
and switch between these five devices.
•
Press 3 to select [RANDOM OFF].
Select a file from a folder/list
Refer to “Select a file to play” on page 13.
Switch between connected
Bluetooth audio devices
Press 5.
Listen to the audio player via Bluetooth
(Pressing the “Play” key on the connected
device itself also causes switching of sound
output from the device.)
1
Press BSRC repeatedly (or press SRC on the remote control) to select
BT AUDIO.
• For
directly.
Operate the audio player via Bluetooth to start playback.
/
: Pressing enters BT AUDIO
* Depending on the connected device, some devices may not support this feature.
2
Operations and display indications may differ according to their availability
on the connected device.
To
On the faceplate
Press 6 IW.
On the remote control
Listen to iPod/iPhone via Bluetooth
Play back/pause
Press ENT IW.
You can listen to the songs on the iPod/iPhone via Bluetooth on this unit.
Press BSRC repeatedly to select iPod BT.
Select group or folder
Press 2 / 1
.
Press #FM+/ AM–.
Press S / T (+).
Reverse skip/
Forward skip
Press S / T.
• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB
input terminal. (Page 11)
• If you plug in an iPod/iPhone to the USB input terminal while listening to
iPod BT source, the source automatically changes to iPod USB source.
Press BSRC to select iPod BT source if the device is still connected via
Bluetooth.
Reverse/Fast-forward
Press and hold S /
T.
Press and hold S /
T (+).
27
ENGLISH
AMAZON ALEXA(for
Alexa is the cloud-based voice service developed by Amazon. You can ask
Alexa to play music, get weather reports, traffic information, control smart
home devices, shop on Amazon, search the internet, set reminders and
more.
/
/
/
/
/
/
)
• The Alexa connection can be disconnected if:
– A2DP profile is disconnected
– Bluetooth is disconnected
– This unit is turned off
– Any other conditions depending on the connected device.
To establish Alexa connection again, reconnect the A2DP profile.
• Alexa connection cannot be established again if you:
Preparation:
application.
– Reinstall Alexa mobile application
• After installing the latest version of the Alexa mobile application on your
device, log in using those credentials.
• Be sure to enable the internet connection on your smartphone.
– Delete the paired device and perform pairing again (for Android device)
To establish Alexa connection again, perform the setup process again.
• You can check the Alexa connection from the Alexa mobile application.
If the name of this unit appears on the screen of “ALL DEVICES”, you do not
need to perform setup process again.
Setup for the first time
For Android device
1
2
3
Pair your device with this unit via Bluetooth. (Page 22)
Start up the Alexa mobile application on your device.
Search and select the name of your receiver (“KDC-X704”/“KDC-X304”/
“KDC-BT778HD”/“KDC-BT378U”/“KDC-BT34”/“KDC-BT360U”/
“KMR-D378BT”) on SETUP section of the Alexa mobile application to
complete a one-time setup process.
For iPhone/iPod touch
Basic operations
1
2
3
Pair your device with this unit via Bluetooth. (Page 22)
Start up the Alexa mobile application on your device.
Press on the unit to enter ALEXA source.
• You may also press B SRC repeatedly to select iPod BT source.
Search and select the name of your receiver (“KDC-X704”/“KDC-X304”/
“KDC-BT778HD”/“KDC-BT378U”/“KDC-BT34”/“KDC-BT360U”/
“KMR-D378BT”) on SETUP section of the Alexa mobile application to
complete a one-time setup process.
Once Alexa connection is established...
1
2
Press on the unit to speak with Alexa.
The display shows: “ALEXA” “LISTENING...”.
4
Communicate with Alexa via the connected microphone. (Page 22)
“THINKING...” appears when Alexa is processing your voice input.
“SPEAKING...” appears while Alexa is responding to your voice input.
“ALEXA” or display information such as playing time, song title, etc.
appears while Alexa is in idle state.
Once the setup process is completed, the Alexa mobile application will
establish a connection with this unit.
28
ENGLISH
AMAZON (for
ALEXA
/
/
/
/
/
/
)
Audio Settings
• To return to the previous source before ALEXA, press BSRC (or press SRC
on the remote control).
• To activate Alexa, press
• To cancel current listening state, press
• To cancel current thinking/speaking states and go to listening state,
press
.
.
.
• Only one Alexa connection can be connected at one time.
• “DISCONNECTED” appears if the unit is disconnected from Alexa mobile
application or the Bluetooth connection is disconnected.
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
Start listening
3
4
Repeat step 2 until the desired item is selected or activated.
Press and hold
to exit.
While in Alexa idle state...
1
Press on the unit to activate Alexa.
The display shows: “LISTENING...”.
Communicate with Alexa via the connected microphone. (Page 22)
During music playback in ALEXA source, you can perform the
following operations:
(or using the remote control)
1
2
Press AUD to enter [AUDIO CONTROL]
Press J/K to select an item, then press ENT IW.
.
2
3
To return to the previous setting item, press
.
To
On the faceplate
Press 6 IW.
On the remote control
Press ENT IW.
Default: [XX]
Play back/pause
[AUDIO CONTROL]
Reverse skip/Forward skip
Press S / T.
Press S / T (+).
[SUB-W LEVEL] [LEVEL –50] to [LEVEL +10] ([LEVEL 0]): Adjusts the subwoofer output
level.
During music playback, press to pause the music and activate Alexa. You
can now start to communicate with Alexa.
[EASY EQ]
Adjusts your own sound settings.
•
•
The settings are stored to [USER] in [PRESET EQ].
The settings made may affect the current settings of [MANUAL EQ].
[SW]: [LEVEL –50] to [LEVEL +10]
[BASS]: [LEVEL –9] to [LEVEL +9]
[MID]: [LEVEL –9] to [LEVEL +9]
[TRE]: [LEVEL –9] to [LEVEL +9]
(Default: [LEVEL 0]
[LEVEL 0]
[LEVEL 0]
[LEVEL 0])
29
ENGLISH
Audio Settings
[MANUAL EQ]
Adjusts your own sound settings for each source.
[SOUND EFFECT]
•
•
The settings are stored to [USER] in [PRESET EQ].
The settings made may affect the current settings of [EASY EQ].
[SOUND RECNSTR] (Not applicable for RADIO source, AUX source and SIRIUS XM source.)
(Sound
reconstruction)
[ON]: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression. ; [OFF]: Cancels.
[62.5HZ]
[LEVEL]
[LEVEL –9] to [LEVEL +9] ([LEVEL 0]): Adjusts
the level to memorize for each source.
(Before making an adjustment, select the source
you want to adjust.)
[SPACE ENHANCE] (Not applicable for RADIO source.)
[SML]/[MED]/[LRG]: Virtually enhances the sound space. ;
[BASS EXTEND] [ON]: Turns on the extended bass. ; [OFF]: Cancels.
[OFF]: Cancels.
[100HZ]/[160HZ]/ [LEVEL –9] to [LEVEL +9] ([LEVEL 0]): Adjusts the level to memorize
[250HZ]/[400HZ]/ for each source.
[SND REALIZER]
[STAGE EQ]
[LV1]/[LV2]/[LV3]: Virtually makes the sound more realistic. ;
[OFF]: Cancels.
[630HZ]/[1KHZ]/
[1.6KHZ]/[2.5KHZ]/
[4KHZ]/[6.3KHZ]/
[10KHZ]/[16KHZ]
(Before making an adjustment, select the source you want to adjust.)
[LOW]/[MID]/[HI]: Virtually adjusts the sound position heard from the
speakers. ; [OFF]: Cancels.
[DRIVE EQ]
[ON]: Boosts the frequency to reduce the noise heard from outside the
car or running noise of the tyres. ; [OFF]: Cancels.
[Q FACTOR]
[PRESET EQ]
[1.35]/[1.50]/[2.00]: Adjusts the quality factor.
[SPEAKER SIZE]
[FRONT]
The frequency and slope settings are automatically set for the crossover
of the selected speaker.
[NATURAL]/[ROCK]/[POPS]/[EASY]/[TOP40]/[JAZZ]/[POWERFUL]/
[USER]: Selects a preset equalizer suitable to the music genre.
(Select [USER] to use the settings made in [EASY EQ] or
[MANUAL EQ].)
[SIZE]
[3.5”]/[4”]/[4.75”]/[5”]/[6.5”]/[6.75”]/[7”]/[4×6]/
[5×7]/[6×8]/[6×9]/[7×10]: Selects according to the
connected speaker size for optimum performance.
[BASS BOOST]
[LOUDNESS]
[LV1] to [LV5]: Selects your preferred bass boost level. ; [OFF]: Cancels.
[TWEETER] [SMALL]/[MIDDLE]/[LARGE]: Selects according to
the size range of the connected tweeter for optimum
performance. ; [NONE]: Not connected.
[LV1]/[LV2]: Selects your preferred low or high frequencies boost to
produce a well-balanced sound at low volume. ; [OFF]: Cancels.
[SUBWOOFER SET]
[FADER]
[ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
[REAR]
[3.5”]/[4”]/[4.75”]/[5”]/[6.5”]/[6.75”]/[7”]/[4×6]/[5×7]/[6×8]/
[6×9]/[7×10]: Selects according to the connected speaker size for
optimum performance. ; [NONE]: Not connected.
[R15] to [F15] ([0]): Adjusts the front and rear speaker output balance.
[L15] to [R15] ([0]): Adjusts the left and right speaker output balance.
[BALANCE]
[SUBWOOFER]
[6.5”]/[8”]/[10”]/[12”]/[15” OVER]: Selects according to the
connected speaker size for optimum performance. ; [NONE]: Not
connected.
[VOLUME OFFSET]
[–15] to [+6] ([0]): Presets the initial volume level of each source by
comparing to the FM volume level.
(Before adjustment, select the source you want to adjust.)
30
ENGLISH
Audio Settings
[X ‘ OVER]
[SW LPF SLOPE] [–6DB]/[–12DB]/[–18DB]/[–24DB]: Adjusts the
crossover slope.
[TWEETER]
[FRQ]
[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/
[6.3KHZ]/[8KHZ]/[10KHZ]/[12.5KHZ]: Adjusts the
crossover frequency for the tweeter speaker.
(Selectable only if a setting other than [THROUGH] is
selected for [SW LPF FRQ].)
[SW LPF
PHASE]
[REVERSE] (180°)/[NORMAL] (0°): Selects the
phase of the subwoofer output to be in line with the
speaker output for optimum performance.
[GAIN LEFT]
[–8] to [0]: Adjusts the output volume of the left
tweeter.
[GAIN RIGHT] [–8] to [0]: Adjusts the output volume of the right
[SW LPF GAIN] [–8] to [0]: Adjusts the output volume of the
tweeter.
subwoofer.
[FRONT HPF]
[F-HPF FRQ]
[30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/
[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/
[220HZ]/[250HZ]: Adjusts the crossover frequency
for the selected speakers (high pass filter). ;
[THROUGH]: All signals are sent to the selected
speakers.
[DTA SETTINGS]
[CAR SETTINGS]
For settings, see “Digital Time Alignment settings” on page 32.
• (For
/
/
)
The following item is selectable only if [SWITCH PREOUT] is set to [SUB-W]
(page 6):
[F-HPF SLOPE] [–6DB]/[–12DB]/[–18DB]/[–24DB]: Adjusts the
crossover slope.
–
–
–
–
–
–
[SUB-W LEVEL]
[SUBWOOFER SET]
(Selectable only if a setting other than [THROUGH] is
selected for [F - HPF FRQ].)
[SW LEVEL] of [EASY EQ]
[SUBWOOFER] of [SPEAKER SIZE]
[SUBWOOFER LPF] of [X ‘ OVER]
[SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]
[F-HPF GAIN] [–8] to [0]: Adjusts the output volume of the
selected speaker.
• The following item is selectable only if [SUBWOOFER SET] is set to [ON]
[REAR HPF]
[R-HPF FRQ]
(page 30):
Configure the settings for the rear speakers similarly
to the front speakers.
–
–
–
–
–
[SUB-W LEVEL]
[R-HPF SLOPE]
[SW LEVEL] of [EASY EQ]
[R-HPF GAIN]
[SUBWOOFER] of [SPEAKER SIZE]
[SUBWOOFER LPF] of [X ‘ OVER]
[SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]
[SUBWOOFER LPF] [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/
[90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/
• The following item is selectable only if a setting other than [NONE] is
[220HZ]/[250HZ]: Adjusts the crossover frequency
for the subwoofer (low pass filter). ; [THROUGH]: All
signals are sent to the subwoofer.
selected for [TWEETER]
[TWEETER] [REAR HPF]
,
,
[REAR] and [SUBWOOFER] of [SPEAKER SIZE]:
[SUBWOOFER LPF] of [X ‘ OVER]
–
,
31
ENGLISH
Audio Settings
• Before making an adjustment for [DISTANCE] and [GAIN] of [DTA SETTINGS]
select the speaker you want to adjust:
,
Digital Time Alignment settings
[FRONT LEFT]
– You can only select [REAR LEFT]
other than [NONE] is selected for [REAR] and [SUBWOOFER] of [SPEAKER SIZE]
[R-SP LOCATION] of [CAR SETTING] is selectable only if a setting other than
/
[FRONT RIGHT]
/
[REAR LEFT]
/[REAR RIGHT]/[SUBWOOFER]
Digital Time Alignment sets the delay time of the speaker output to create a
more suitable environment for your vehicle.
• For more information, see the following “Determining the delay time
automatically”.
,
[REAR RIGHT] and [SUBWOOFER] if a setting
.
•
[NONE] is selected for [REAR] of [SPEAKER SIZE]
.
[DTA SETTINGS]
[POSITION]
Selects your listening position (reference point).
[ALL]: Not compensating ; [FRONT RIGHT]: Front right seat ;
Determining the delay time automatically
If you specify the distance from the currently set
listening position to every speaker, the delay time
will be automatically calculated.
[FRONT LEFT]: Front left seat ; [FRONT ALL]: Front seats
[DISTANCE]
[GAIN]
[0FT] to [20.01FT]: Fine adjust the distance to compensate.
(Before making an adjustment, select the speaker you want to adjust.)
1
Set [POSITION] and determine the listening
position as the reference point (the reference
point for [FRONT ALL] will be the center
between the right and left in the front seats).
[–8DB] to [0DB]: Fine adjust the output volume of the selected
speaker.
(Before making an adjustment, select the speaker you want to adjust.)
2
3
Measure the distances from the reference point to
the speakers.
Calculate the distance between the furthest
speaker (subwoofer on the illustration) and other
speakers.
[DTA RESET]
[CAR SETTINGS]
[CAR TYPE]
[YES]: Resets the settings ([DISTANCE] and [GAIN]) of the selected
[POSITION] to default. ; [NO]: Cancels.
Identify your car type and rear speaker location in order to make the
adjustment for [DTA SETTINGS].
4
5
Sets the [DISTANCE] calculated in step 3 for
individual speakers.
Adjusts [GAIN] for individual speakers.
[COMPACT]/[FULL SIZE CAR]/[WAGON]/[MINIVAN]/[SUV]/
[MINIVAN(LONG)]: Selects the type of vehicle. ; [OFF]: Not
compensating.
Example: When [FRONT ALL] is selected as the
listening position.
[R-SP LOCATION]
Selects the location of the rear speakers in your vehicle to calculate the
furthest distance from the listening position selected (reference point).
• [DOOR]/[REAR DECK]: Selectable only when [CAR TYPE] is
selected as [OFF], [COMPACT], [FULL SIZE CAR], [WAGON] or
[SUV].
• [2ND ROW]/[3RD ROW]: Selectable only when [CAR TYPE] is
selected as [MINIVAN] or [MINIVAN(LONG)].
32
ENGLISH
Display Settings
Zone identification for color settings and brightness settings
Change the display settings
1
2
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item (see the following table), then
press the knob.
3
4
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
Press and hold
to exit.
To return to the previous setting item, press
.
Zone identification for brightness setting
Default: [XX]
[DISPLAY]
[COLOR SELECT]
(For
/
/
)
/
/
/
Selects illumination colors for [ALL ZONE], [ZONE 1] and [ZONE 2]
separately.
1
2
Select a zone. (See the illustration on left column.)
Select a preset color for the selected zone. (Page 34)
Default:
/
/
/
/
Set the dimmer
: [VARIABLE SCAN]
: [INITIAL COLOR]
Press and hold DISP (DIM) to turn on or off the dimmer.
• Once you press and hold this button, [DIMMER] setting (page 34) will be
overwritten.
To make your own color, select [CUSTOM R/G/B]. The color you have made
will be stored in [CUSTOM R/G/B].
1
2
3
Press the volume knob to enter the detailed color adjustment.
Press to select the color ([R]/[G]/[B]) to adjust.
Turn the volume knob to adjust the level ([0] to [9]), then press the knob.
S
/T
33
ENGLISH
Display Settings
[DIMMER]
Dims the illumination.
[ON]: Dimmer is turned on.
[OFF]: Dimmer is turned off.
[CLOCK]
[CLOCK DISPLAY]
(Except for
)
[ON]: The clock time is shown on the display even when the unit is turned
off. ; [OFF]: Cancels.
[DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer.
1
2
Turn the volume knob to adjust the [ON] time, then press the knob.
Turn the volume knob to adjust the [OFF] time, then press the knob.
Default: [ON]: [6:00PM] ; [OFF]: [6:00AM]
[DEMO MODE]
(Except for
)
[ON]: Activates the display demonstration automatically if no operation is
done for about 15 seconds. ; [OFF]: Deactivates.
[BRIGHTNESS]
Sets the brightness for day and night separately.
1
2
3
[DAY]/[NIGHT]: Select day or night.
Select a zone. (See the illustration on page 33.)
[LVL00] to [LVL31]: Set the brightness level.
Preset color:
[INITIAL COLOR]
/
[VARIABLE SCAN]
[PURPLE3] [PURPLE4]
[LIGHTBLUE] [AQUA1] [AQUA2] [GREEN1]
[YELLOWGREEN2] [YELLOW] [ORANGE1] [ORANGE2]/
/
/
[CUSTOM R/G/B]
[BLUE1] [BLUE2]
[GREEN2]
/
/
[RED1]
[BLUE3]
[GREEN3]
[ORANGERED]
/
[RED2]
[SKYBLUE1]
[YELLOWGREEN1]/
/
[RED3]
/[PURPLE1]/
[TEXT SCROLL] [ONCE]: Scrolls the display information once. ; [AUTO]: Repeats scrolling at
[PURPLE2]
/
/
/
/
/
/
/
[SKYBLUE2]/
5-second intervals. ; [OFF]: Cancels.
/
/
/
/
/
/
/
[LEVEL METER]
(For
/
/
)
/
/
/
[ON]: Shows the level meter on the display window (as shown below). ;
[OFF]: Cancels.
Level meter
34
ENGLISH
Learning Steering Remote Control(for
You can control the unit with the steering remote control keys on your
vehicle. After connection, you can configure the control keys according to
your preference.
• You can only make this configuration if your vehicle is equipped with the
electrical steering remote control.
• If the steering remote control in your car is not compatible, configuration
may not be completed and an error message may appear. (Page 44)
)
7
8
Press and hold any control keys on your steering remote control
which you want to assign.
A list of key functions will appear on the display.
[NONE] (default)/[ATT]
[ON HOOK] [OFF HOOK]
Turn the volume knob to select a function to assign, then press the
knob.
/
[SEEK UP]
/[SEEK DOWN]/[VOL UP]/[VOL DOWN]/[MODE]/
/
/[VOICE] [ENTER]
/
The selected key function is assigned to the steering remote control key
you have selected in step 7.
The display returns to the key list as on step 5.
Make the connection
Bright green/red
•
[K## (Function)]: When certain function has been assigned to a key.
Repeat step 6 to step 8 to assign other control keys.
to exit.
Steering remote cable (supplied)
9
Purple/red
10 Press and hold
Gray/red
Learning steering
remote input terminal
Reassign the control keys
1
2
3
4
5
6
Press BSRC repeatedly to enter STANDBY.
Connect to your vehicle’s steering remote harness.
Contact your KENWOOD dealer for details.
Press the volume knob to enter [FUNCTION]
.
Rear panel
Turn the volume knob to select [SYSTEM], then press the knob.
Turn the volume knob to select [USER S.REMO], then press the knob.
Turn the volume knob to select [RESET KEY], then press the knob.
Turn the volume knob to select [YES], then press the knob.
All the control keys will be reset.
Configure the control keys
Press BSRC repeatedly to enter STANDBY.
1
2
3
4
5
Press the volume knob to enter [FUNCTION]
.
Selecting [NO] will cancel the operation.
Turn the volume knob to select [SYSTEM], then press the knob.
Turn the volume knob to select [USER S.REMO], then press the knob.
Turn the volume knob to select [SET KEY], then press the knob.
A key list of 16 assignable keys appears.
When [FACTORY RESET] is set to [YES] (page 7), it will also reset the learning
steering remote control.
To return to the previous setting item, press
.
•
[K## NONE]: No function has been assigned.
6
Turn the volume knob to select any key from the key list to assign the
function, then press the knob.
“PRESS KEY TO ASSIGN K##” appears.
35
ENGLISH
Installation/Connection
Part list for installation
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
(A) Faceplate (×1)
(B) Trim plate (×1)
WARNING
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• To prevent short circuit:
(C) Mounting sleeve (×1)
(D) Wiring harness (×1)
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires
that comes into contact with metal parts to protect the wires.
(E) Extraction key (×2)
(F) Screws*
M5 × 7 mm (×4)
M5 × 6 mm (×4)
M4 × 8 mm (×1)
CAUTION
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
* Supplied for
/
/
/
/
.
• Do not connect the wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Mount the unit at an angle of less than 30°.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
Basic procedure
1
2
3
Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
Connect the wires properly.
See “Wiring connection” on page 38.
Install the unit to your car.
See “Installing the unit (in-dash mounting)” on page 37.
Connect the terminal of the car battery.
Press BSRC to turn on the power.
4
5
6
• If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
Detach the faceplate and reset the unit within 5 seconds. (Page 4)
36
ENGLISH
Installation/Connection
Installing the unit (in-dash mounting)
Installing the unit (without mounting sleeve)
1
2
Remove the mounting sleeve and trim plate from the unit.
Align the holes in the unit (on both sides) with the vehicle mounting
bracket and secure the unit with screws (supplied/commercially
available).
Use only the specified screws. Using wrong screws might damage the
unit.
Removing the unit
Do the required wiring.
(Page 38)
1
2
Detach the faceplate.
Fit the catch pin on the extraction keys into the holes on both sides
of the trim plate, then pull it out.
3
Insert the extraction keys deeply into the slots on each side, then
follow the arrows as shown on the illustration.
Hook on the top side
Orientate the trim
Dashboard of your car
plate as illustrated
before fitting.
Bend the appropriate tabs to hold the sleeve
firmly in place.
37
ENGLISH
Installation/Connection
Wiring connection
IMPORTANT
We recommend installing the unit with a commercially available custom wiring harness specific
for your car and leave this job to professionals for your safety. Consult your car audio dealer.
Fuse (10 A)
Antenna terminal
White
If no connections are made, do not let the wire come out from the tab.
To connect the KENWOOD navigation system, refer your
To front speaker (left)
White/Black
Gray
Brown
To front speaker (right) Gray/Black
navigation manual
(Mute control wire)
Green
To rear speaker (left) Green/Black
Purple
To the power control terminal when using the optional
power amplifier or to the antenna control terminal in the
vehicle
Blue/White
To rear speaker (right)
Purple/Black
(Power control wire/
Antenna control wire)
(12 V 350 mA)
Car fuse box
(For
/
/
/
/
/
Ignition switch
Red (Ignition wire)
Yellow (Battery wire)
/
/
)
Light blue/yellow
To the steering wheel remote control adapter
(For
To KENWOOD Marine Remote Control unit (optional
accessory)
For the latest information on marine accessories, visit
<http://www.kenwood.com/usa/car/marine/>
(Steering remote control wire)
)
Car fuse
box
Black (Ground wire)
To the metallic body or chassis of the car
Battery
38
ENGLISH
Installation/Connection
Connect external components
Connect external amplifiers via output terminals
When connecting to an external amplifier to the output terminals of this
unit, firmly connect the ground wire of the amplifier to the car’s chassis to
avoid damaging the unit.
Model
Output terminals
REAR:
/
/
Rear output
/
FRONT:
SW:
Front output
/
/
/
Subwoofer output
No Part
1
2
For
: Learning steering remote control (Page 35)
REAR/SW:
Rear/subwoofer output
For
: To KENWOOD Marine Remote Control unit, KCA-RC55MR
(optional accessory) (Page 7)
FRONT:
Front output
Output terminals (See the following “Connect external amplifiers via output terminals”.)
3
4
REAR/SW:
Rear/subwoofer output
For
/
/
/
/
/
: Expansion port (12 V 500 mA):
To the optional SiriusXM Vehicle Tuner (commercially available) (Page 17)
Microphone input jack (Page 22)
5
39
ENGLISH
References
Playable files
Maintenance
•
Playable audio file:
Cleaning the unit
For disc: MP3 (.mp3), WMA (.wma), AAC (.aac)
For USB mass storage class device:
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.flac)
Playable disc media: CD-R/CD-RW/CD-ROM
•
•
•
Cleaning the connector
Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name
Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or devices.
The AAC (.m4a) file in a CD encoded by iTunes cannot be played on this unit.
Detach the faceplate and clean the connector gently
with a cotton swab. Be careful not to damage the
connector.
Connector (on the reverse
side of the faceplate)
Handling discs
Unplayable discs
•
•
•
•
•
•
•
Do not touch the recording surface of the disc.
Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
Do not use any accessories for the disc.
•
•
•
•
Discs that are not round.
Discs with coloring on the recording surface or discs that are dirty.
Recordable/ReWritable discs that have not been finalized.
8 cm CD. Attempting to insert using an adapter may cause malfunction.
Clean from the center of the disc and move outward.
Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
When removing a disc from this unit, pull it out horizontally.
Remove burrs from the center hole and disc edge before inserting a disc.
About USB devices
•
•
•
You cannot connect a USB device via a USB hub.
Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1.5 A.
More information
For:
–
–
–
Latest firmware updates and latest compatible item list
KENWOOD original application
Any other latest information
About iPod/iPhone
•
Made for
– iPod touch (6th generation)
Visit <www.kenwood.com/cs/ce/>.
– iPhone 5S, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus, 8, 8 Plus, X, XS, XS MAX, XR (iOS 12.1 or later)
It is not possible to browse video files on the “Videos” menu in [MODE OFF].
The song order displayed on the selection menu of this unit may differ from that of the iPod/
iPhone.
•
•
General
•
This unit can only play the following CDs:
•
•
You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.
Depending on the version of the operating system of the iPod/iPhone, some functions may not
operate on this unit.
•
For detailed information and notes about the playable audio files, visit
<www.kenwood.com/cs/ce/audiofile/>.
40
ENGLISH
References
About Pandora
For Radio Data System:
[SPEECH]:
•
Pandora is only available in certain countries.
[NEWS], [AFFAIRS], [INFO] (information), [SPORT], [EDUCATE], [DRAMA], [CULTURE],
[SCIENCE], [VARIED], [WEATHER], [FINANCE], [CHILDREN], [SOCIAL], [RELIGION],
[PHONE IN], [TRAVEL], [LEISURE], [DOCUMENT]
For more information, visit <www.pandora.com/legal>.
•
Because Pandora is a third-party service, the specifications are subject to change without prior
notice. Accordingly, compatibility may be impaired, or some or all of the services may become
unavailable.
Some functions of Pandora cannot be operated from this unit.
For issues using the application, please contact Pandora at <pandora-support@pandora.com>.
[MUSIC]:
[POP M] (music), [ROCK M] (music), [EASY M] (music), [LIGHT M] (music), [CLASSICS],
[OTHER M] (music), [JAZZ], [COUNTRY], [NATION M] (music), [OLDIES], [FOLK M] (music)
•
•
The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.
About Spotify
•
Spotify application supports:
– iPhone 5S, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus, 8, 8 Plus, X, XS, XS MAX, XR (iOS 12.1 or later)
– iPod touch (6th generation)
About HD Radio™ Technology
•
Adjacent to traditional main stations are extra local FM channels. These
HD2/HD3 Channels provide new, original music as well as deep cuts
into traditional genre.
– Android OS 4.0.3 or above
•
Spotify is a third party service, therefore the specifications are subject to change without prior
notice. Accordingly, compatibility may be impaired or some or all of the services may become
unavailable.
Some functions of Spotify cannot be operated from this unit.
For issues using the application, please contact Spotify at <www.spotify.com>.
•
Digital, CD-quality sound. HD Radio Technology enables local radio
stations to broadcast a clean digital signal. AM sounds like today’s FM
and FM sounds like a CD.
•
•
•
•
Program Info provides song name, artist, station ID, and other relevant
data to enrich the listening experience.
About AMAZON ALEXA
•
Emergency Alert delivers critical and life-saving messages to the public
during emergency situations.
Alexa is a third party service, therefore the specifications are subject to change without prior
notice. Accordingly, compatibility may be impaired or some or all of the services may become
unavailable.
About Program Type
For Radio Broadcast Data System:
[SPEECH]:
[NEWS], [INFORM] (information), [SPORTS], [TALK], [LANGUAGE], [REL TALK] (religious
talk), [PERSNLTY] (personality), [PUBLIC], [COLLEGE], [HABL ESP] (spanish talk), [WEATHER]
[MUSIC]:
[ROCK], [CLS ROCK] (classic rock), [ADLT HIT] (adult hits), [SOFT RCK] (softrock), [TOP 40],
[COUNTRY], [OLDIES], [SOFT], [NOSTALGA] (nostalgia), [JAZZ], [CLASSICL] (classical),
[R & B] (rhythm and blues), [SOFT R&B] (soft rhythm and blues), [REL MUSC] (religious
music), [MUSC ESP] (spanish music), [HIP HOP]
41
ENGLISH
References
Source name Display information: Main display
Change the display information
CD or USB
For CD-DA:
(For
/
/
/
/
/
Disc title/Artist Track title/Artist Playing time Date back to the
beginning
)
Each time you press DISP, the display information changes.
•
If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information
(eg. station name) appears or display will be blank.
For MP3/WMA/AAC/WAV/FLAC files:
Song title/Artist Album title/Artist Folder name File name Playing
time Date back to the beginning
iPod USB/iPod BT When [MODE OFF] is selected (page 12):
Song title/Artist Album title/Artist Playing time Date back to the
Main display
beginning
Level meter (Page 34)
Source name Display information: Main display
Clock time
PANDORA/
PANDORA BT
Station name Shared/Radio Title Artist Album title Playing time
Date back to the beginning
SPOTIFY/
SPOTIFY BT
Context title Song title Artist Album title Playing time Date
back to the beginning
STANDBY
HD RADIO
Source name Date back to the beginning
(For
For digital stations only:
SIRIUS XM
Channel number Channel name Artist Song title Content
information Category name Date back to the beginning
/
)
BT AUDIO/
ALEXA
Song title/Artist Album title/Artist Playing time Date back to the
beginning
Station name Title/Artist Album/Artist Frequency Date back
to the beginning
AUX
Source name Date back to the beginning
For FM Radio Broadcast Data System stations only:
Radio text+ station name Radio text+ title/Radio text+ artist
Radio text+ album/Radio text+ artist Frequency Date back to the
beginning
RADIO
(For
/
/
/
)
Frequency Date back to the beginning
For FM Radio Broadcast Data System stations only:
Station name/Program type Radio text Radio text+ Radio text+
song title/Radio text+ artist Frequency Date back to the beginning
42
ENGLISH
References
(For
/
/
)
Source name Display information: Main display
Each time you press DISP, the display information changes.
PANDORA/
Source name/Clock Station name Shared/Radio Title Artist
•
If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information
(eg. station name) appears or display will be blank.
PANDORA BT
Album title Playing time Clock back to the beginning
SPOTIFY/
SPOTIFY BT
Source name/Clock Context title Song title Artist Album title
Playing time Clock Turns off the display* back to the beginning
Main display
BT AUDIO/
ALEXA
Source name/Clock Song title/Artist Album title/Artist Playing time
Clock Turns off the display* back to the beginning
AUX
Source name/Clock Clock Turns off the display* back to the
beginning
Source name Display information: Main display
* Only for
.
STANDBY
Source name/Clock Clock Turns off the display* back to the
beginning
RADIO
Source name/Clock Frequency Clock Turns off the display* back
to the beginning
For FM Radio Broadcast Data System/FM Radio Data System stations only:
Source name/Clock Station name/Program type Radio text
Radio text+ Radio text+ song title/Radio text+ artist Frequency
Clock Turns off the display* back to the beginning
CD or USB
For CD-DA:
Source name/Clock Disc title/Artist Track title/Artist Playing time
Clock Turns off the display* back to the beginning
For MP3/WMA/AAC/WAV/FLAC files:
Source name/Clock Song title/Artist Album title/Artist Folder name
File name Playing time Clock Turns off the display* back to
the beginning
iPod USB/iPod BT When [MODE OFF] is selected (page 12):
Source name/Clock Song title/Artist Album title/Artist Playing time
Clock Turns off the display* back to the beginning
43
ENGLISH
Troubleshooting
Symptom
Remedy
Symptom
Disc cannot be ejected.
Remedy
Sound cannot be heard.
•
•
Adjust the volume to the optimum level.
Check the cords and connections.
Press and hold to forcibly eject the disc. Be careful not
to drop the disc when it is ejected. If this does not solve
the problem, reset the unit (page 4).
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
Turn the power off, then check to be sure the terminals
of the speaker wires are insulated properly. Turn the
power on again.
Noise is generated.
Skip to another track or change the disc.
“PLEASE EJECT” appears.
Reset the unit (page 4). If this does not solve the
problem, consult your nearest service center.
“PROTECTING SEND SERVICE” Send the unit to the nearest service center.
appears.
Playback order is not as
intended.
The playback order is determined by the order in which
files were recorded (disc) or the file name (USB).
Source cannot be selected.
Check the [SOURCE SELECT] setting. (Page 6)
•
•
•
Sound cannot be heard.
The unit does not turn on.
Information shown on the
display is incorrect.
Clean the connectors. (Page 40)
Elapsed playing time is not
correct.
This depends on the recording process earlier (disc/USB).
“READING” keeps flashing.
•
•
Do not use too many hierarchical levels and folders.
Reload the disc or reattach the device (USB/iPod/
iPhone).
The unit does not work at all. Reset the unit. (Page 4)
Correct characters are not
displayed.
•
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
Depending on the display language you have selected
(page 7), some characters may not be displayed
correctly.
“UNSUPPORTED DEVICE”
appears.
•
•
Check whether the connected USB device is compatible
with this unit and ensure the file systems are in
supported formats. (Page 40)
•
Reattach the USB device.
“UNRESPONSIVE DEVICE”
appears.
Make sure the USB device is not malfunction and reattach
the USB device.
Setting/deleting the remote control ID is unsuccessful.
Turn the power off, then turn on the power and perform
the operation again. (Page 7)
(For
)
“SET ERROR”/“DEL ERROR”
“USB HUB IS NOT
SUPPORTED” appears.
This unit cannot support a USB device connected via a
USB hub.
Your steering remote controller is not compatible,
learning may not be completed. Consult your car audio
dealer for details.
(For
)
•
The source does not
change to “USB” when
you connect a USB device
while listening to another
source.
The USB port is drawing more power than the design
limit. Turn the power off and unplug the USB device.
Then, turn on the power and reattach the USB device.
If this does not solve the problem, turn the power off and
on (or reset the unit) before replacing with another USB
device.
“ERROR”/”FAILED”
•
•
Radio reception is poor.
Static noise while listening
to the radio.
Connect the antenna firmly.
•
“USB ERROR” appears.
44
ENGLISH
Troubleshooting
Symptom
Remedy
Symptom
“CONNECT ERROR”
Remedy
The iPod/iPhone does not
turn on or does not work.
•
•
Check the connection between this unit and iPod/iPhone.
Disconnect and reset the iPod/iPhone using hard reset.
Communication is unstable.
“RATING ERROR”
Registration of thumbs up/thumbs down has failed due to
insufficient network connectivity.
“LOADING” appears when
you enter search mode by
pressing
This unit is still preparing the iPod/iPhone music list. It
may take some time to load, try again later.
“THUMBS N/A”
Registration of thumbs up/thumbs down is not allowed.
.
“LICENSE ERROR”
You try to access from a country which Pandora is not
deliverable.
“NO DISC”
“TOC ERROR”
“NA FILE”
Insert a playable disc into the loading slot.
Make sure the disc is clean and inserted properly.
“DISCONNECTED”
“CONNECTING”
USB is disconnected from the head unit. Please make sure
the device is connected properly through USB.
Make sure the media (disc/USB) contain supported audio
files. (Page 40)
•
•
Connected via USB input terminal: The device is
connecting to the head unit. Please wait.
Connected via Bluetooth: The Bluetooth is disconnected.
Please check Bluetooth connection and make sure both
the device and unit are paired and connected.
“COPY PRO”
“NO DEVICE”
A copy-protected file is played (disc/USB).
Connect a device (USB/iPod/iPhone), and change the
source to USB/iPod USB again.
“NO MUSIC”
Connect a device (USB/iPod/iPhone) that contains
playable audio files.
“CHECK APP”
The Spotify application is not connected properly or user
is not login. End the Spotify application and restart. Then,
log in to your Spotify account.
“iPod ERROR”
“MEMORY FULL”
•
•
Reconnect the iPod.
Reset the iPod.
“CH LOCKED LOCK CODE?”
“CHAN UNSUB”
The selected channel is locked. Enter the correct pass code
to unlock. (Page 19)
You have reached the maximum storage limit of your
iPod/iPhone.
The selected channel is unsubscribed.
“ADD ERROR”
“CHECK DEVICE”
“NO SKIPS”
New station creation is unsuccessful.
Check the Pandora application on your device.
The skip limit has been reached.
No stations are found.
Call 1-866-635-2349 in the U.S.A. or 1-877-438-9677 in
Canada to subscribe. (Page 17)
“CH UNAVAIL”
The selected channel is unavailable. For more
information about the SiriusXM channel lineup, visit
<www.siriusxm.com>.
“NO STATIONS”
“STATION LIMIT”
The number of registered stations has reached its limit.
Retry after deleting unnecessary stations from your
device.
“CHECK ANTENNA”
“CHECK TUNER”
Check that the antenna and its connection are in good
condition.
Make sure the SiriusXM Vehicle Tuner is connected to the
unit.
“UPGRADE APP”
Make sure you have installed the latest version of the
Pandora application on your device.
45
ENGLISH
Troubleshooting
Symptom
Remedy
Symptom
Sound is being interrupted
Remedy
“NO SIGNAL”
Make sure the antenna is mounted outside the vehicle.
•
Reduce the distance between the unit and the Bluetooth
audio player.
Turn off, then turn on the unit and try to connect again.
Other Bluetooth devices might be trying to connect to the
unit.
or skipped during playback
of a Bluetooth audio player.
“SUBSCRIPTION UPDATED
– PRESS ENTER TO
CONTINUE.”
Your subscription is updated. Press the volume knob to
continue.
•
•
“CODE ERROR”
Make sure you have entered the correct pass code.
(Page 19)
The connected Bluetooth
audio player cannot be
controlled.
•
•
Check whether the connected Bluetooth audio player
supports Audio/Video Remote Control Profile (AVRCP).
(Refer to the instructions of your audio player.)
“NO CONTENT”
“SCAN CANCEL”
There is insufficient content to start TuneScan.
TuneScan has been aborted.
Disconnect and connect the Bluetooth player again.
“NOT SUPPORT”
The connected phone does not support Voice Recognition
feature or phonebook transfer.
No Bluetooth device is
detected.
•
•
Search from the Bluetooth device again.
Reset the unit. (Page 4)
“NO ENTRY”/“NO PAIR”
“ERROR”
There is no registered device connected/found via
Bluetooth.
Bluetooth pairing cannot
be made.
•
Make sure you have entered the same PIN code to both
the unit and Bluetooth device.
Delete pairing information from both the unit and the
Bluetooth device, then perform pairing again. (Page 22)
•
Try the operation again. If “ERROR” appears again, check if
the device supports the function you have tried.
Echo or noise is
heard during a phone
conversation.
•
•
Adjust the microphone unit’s position. (Page 22)
Check the [ECHO CANCEL] setting. (Page 24)
“NO INFO”/“NO DATA”
Bluetooth device cannot get the contact information.
“HF ERROR XX”/
“BT ERROR”
Reset the unit and try the operation again. If this does not
solve the problem, consult your nearest service center.
Phone sound quality is
poor.
•
•
Reduce the distance between the unit and the Bluetooth
device.
Move the car to a place where you can get a better signal
reception.
“SWITCHING NG”
The connected phones might not support phone switching
feature.
The Bluetooth connection
between the Bluetooth
device and the unit is
unstable.
Delete the unused registered Bluetooth device from the
unit. (Page 26)
Voice calling method is not
successful.
•
•
Use voice calling method in a more quiet environment.
Reduce the distance from the microphone when you speak
the name.
•
Make sure the same voice as the registered voice tag is
used.
46
ENGLISH
Troubleshooting
Specifications
Symptom
Remedy
/
:
No response from Alexa
after the voice input.
Amazon cloud was unable to analyze the voice input.
FM
Frequency Range
87.9 MHz — 107.9 MHz (200 kHz step)
7.2 dBf (0.63 μV/75 Ω)
Usable Sensitivity
(S/N = 30 dB)
Wrong response from
Alexa.
Alexa misunderstood what was said or did not catch
the entire request or sentence spoken. Please try again.
(Page 28)
Quieting Sensitivity
(DIN S/N = 46 dB)
15.2 dBf (1.58 μV/75 Ω)
30 Hz — 15 kHz
“DISCONNECTED”
Be sure to connect your smartphone to the unit via
Bluetooth. (Page 22)
Frequency Response ( 3 dB)
Signal-to-Noise Ratio (MONO) 68 dB
Not able to connect or
reconnect to Alexa mobile
application.
•
•
Be sure the audio device is connected via Bluetooth. Select
the audio device from [AUDIO SELECT] in [BT MODE].
(Page 26)
Perform the one-time setup process again. See “Setup for
the first time” on page 28.
Stereo Separation (1 kHz)
40 dB
Digital Frequency Range
FM
87.9 MHz — 107.9 MHz (200 kHz step)
20 Hz — 20 kHz
Frequency Response ( 3 dB)
•
•
Turn off, then turn on the unit and try to connect again.
For iOS device, make sure Alexa source or iPod BT source is
selected.
Signal-to-Noise Ratio (STEREO) 75 dB
AM
Frequency Range
530 kHz — 1 700 kHz (10 kHz step)
Usable Sensitivity (S/N = 20 dB) 29 dBμ (28.2 μV)
Digital Frequency Range
AM
530 kHz — 1 700 kHz (10 kHz step)
40 Hz — 15 kHz
Frequency Response ( 3 dB)
Signal-to-Noise Ratio (STEREO) 70 dB
47
ENGLISH
Specifications
Laser Diode
GaAIAs
/
/
/
/
/
/
:
Digital Filter (D/A)
8 times over sampling
500 rpm — 200 rpm (CLV)
Below measurable limit
20 Hz — 20 kHz
FM
Frequency Range
/
/
/
Spindle Speed
/
/
Wow & Flutter
:
87.9 MHz — 107.9 MHz (200 kHz step)
Frequency Response ( 1 dB)
Total Harmonic Distortion (1 kHz)
:
/
:
:
:
87.5 MHz — 108.0 MHz (50 kHz step)
0.01 %
Usable Sensitivity
(S/N = 30 dB)
8.2 dBf (0.71 μV/75 Ω)
17.2 dBf (2.0 μV/75 Ω)
/
/
/
/
/
:
/
/
/
Quieting Sensitivity
(DIN S/N = 46 dB)
0.02 %
Frequency Response ( 3 dB)
Signal-to-Noise Ratio (MONO)
Stereo Separation (1 kHz)
Frequency Range
30 Hz — 15 kHz
Signal-to-Noise Ratio (1 kHz)
/
64 dB
97 dB
40 dB
/
/
/
AM
530 kHz — 1 700 kHz (10 kHz step)
/
/
:
Usable Sensitivity (S/N = 20 dB) 29 dBμ (28.2 μV)
99 dB
Dynamic Range
/
89 dB
/
/
/
/
/
:
92 dB
48
ENGLISH
Specifications
Channel Separation
Frequency Response ( 3 dB)
Input Maximum Voltage
Input Impedance
20 Hz — 20 kHz
1 000 mV
/
/
:
89 dB
90 dB
/
/
30 kΩ
/
/
:
/
Version
Bluetooth 4.2
Frequency Range
RF Output Power (E.I.R.P.)
Maximum Communication Range
Profile
2.402 GHz — 2.480 GHz
+4 dBm (MAX), Power Class 2
Line of sight approx. 10 m (32.8 ft)
MP3 Decode
WMA Decode
AAC Decode
Compliant with MPEG-1/2 Audio Layer-3
Compliant with Windows Media Audio
AAC-LC “.aac” files
HFP 1.7.1 (Hands-Free Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP 1.6.1 (Audio/Video Remote Control Profile)
PBAP (Phonebook Access Profile)
SPP (Serial Port Profile)
USB Standard
File System
USB 1.1, USB 2.0 (High speed)
FAT12/16/32
Maximum Supply Current
MP3 Decode
DC 5 V 1.5 A
Compliant with MPEG-1/2 Audio Layer-3
Compliant with Windows Media Audio
AAC-LC “.aac”, “.m4a” files
Linear-PCM
Maximum Output Power
50 W × 4
22 W × 4
WMA Decode
AAC Decode
Full Bandwidth Power
(at less than 1 % THD)
Speaker Impedance
4 Ω — 8 Ω
WAV Decode
FLAC Decode
FLAC file (Up to 96 kHz/24 bit)
49
ENGLISH
Specifications
Tone Action
Band 1: 62.5 Hz 9 dB
Band 2: 100 Hz 9 dB
Band 3: 160 Hz 9 dB
Band 4: 250 Hz 9 dB
Band 5: 400 Hz 9 dB
Band 6: 630 Hz 9 dB
Band 7: 1 kHz 9 dB
Band 8: 1.6 kHz 9 dB
Band 9: 2.5 kHz 9 dB
Band 10: 4 kHz 9 dB
Band 11: 6.3 kHz 9 dB
Band 12: 10 kHz 9 dB
Band 13: 16 kHz 9 dB
Preout Level/Load
/
:
5 000 mV/10 kΩ
/
:
4 000 mV/10 kΩ
/
/
/
/
:
2 500 mV/10 kΩ
Preout Impedance
Operating Voltage
≤ 600 Ω
12 V DC car battery
Installation Size (W × H × D)
182 mm × 53 mm × 155.5 mm
(7-3/16" × 2-1/16" × 6-1/8")
Net Weight (includes Trimplate,
Mounting Sleeve)
1.2 kg (2.7 lbs)
Subject to change without notice.
50
ENGLISH
•
•
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and Foreign
are registered trademarks or trademarks of iBiquity Digital Corporation in the United States and/or
other countries.
Use of the Made for Apple badge means that an accessory has been designed to connect specifically
to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance
with safety and regulatory standards. Please note that the use of this accessory with an Apple product
may affect wireless performance.
Apple, iPhone, iPod, iPod touch, iTunes, and Lightning are trademarks of Apple Inc., registered in the
U.S. and other countries.
libFLAC
Copyright (C) 2000-2009 Josh Coalson
Copyright (C) 2011-2013 Xiph.Org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
-
-
-
Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to
endorse or promote products derived from this software without specific prior written permission.
•
•
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
•
•
Android is a trademark of Google LLC.
©2019 Pandora Media, LLC. All rights reserved. PANDORA, the PANDORA logo, and the Pandora trade
dress are trademarks or registered trademarks of Pandora Media, LLC. Used with permission.
SPOTIFY and the Spotify logo are among the registered trademarks of Spotify AB.
Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and
any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade
names are those of their respective owners.
•
•
•
•
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
ENGLISH
FRANÇAIS
ESPAÑOL
KDC-BT278U
CD-RECEIVER
Quick Start Guide
AUTORADIO CD
Guide de démarrage rapide
RECEPTOR CD
Guía de inicio rápido
For detailed operations and information, refer to the
INSTRUCTION MANUAL on the following website:
Pour les opérations et les informations détaillées,
reportez-vous au MODE D’EMPLOI sur le site web suivant:
Para obtener más información y detalles sobre las
operaciones, consulte el MANUAL DE INSTRUCCIONES en el
siguiente sitio web:
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided
below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-BT278U
Serial number
US Residents Only
<www.kenwood.com/cs/ce/>
Register Online
Register your Kenwood product at http://www.kenwood.com/usa/
© 2019 JVCKENWOOD Corporation
B5K-0722-00 [KN]
CAUTION
FCC CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product
relating to laser product safety.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
JVCKENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR
SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
Location : Top Plate
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida
útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de
residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser
desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final
de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento
adecuado a estos productos y a sus subproductos residuales correspondientes.
Póngase en contacto con su administración local para obtener información sobre el
punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación
de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos
perjudiciales en la salud y el medio ambiente.
Supplier's Declaration of Conformity
Trade Name: KENWOOD
Products: CD-RECEIVER
Model Name: KDC-BT278U
Responsible Party: JVCKENWOOD USA CORPORATION
2201 East Dominguez Street, Long Beach, CA 90810, U.S.A.
PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou
entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao
mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
i
SOFTWARE LICENSE AGREEMENT
IC (Industry Canada) Caution
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is
copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions
which Users shall follow in order to use the Licensed Software.
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the
Product in which the "Licensed Software" is embedded.
Attention de ‘IC (Industrie Canada)
The Licensed Software may include the software which has been licensed to the Licensor directly or
indirectly from any third party. In such case, some third parties require the Users to follow their conditions
for use separately from this Software License Agreement. Such software shall not be subject to this
Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided
separately below.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage.
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Article 1
General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case
referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.
(the country where the User bought the Product (hereinafter the "Country")
Contains Bluetooth Module:
FCC ID: ZWY88112
IC ID: 12033A-88112
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
Article 2
License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the
Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed
Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall
not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation
manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright
Law or any other laws and regulations by applying whole or a part of the Licensed Software.
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at
least 20 cm or more away from person’s body.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices
d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit
être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.
Article 3
Conditions for Grant of License
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software
embedded in the Product (including any related materials, updates and upgrades) on condition that
no original, copies or related materials continue in the possession of the User, and that the User shall
cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code
analysis works in connection with the Licensed Software.
Para cumplimiento de la IFT:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada”
ii
Article 4
Right pertaining to the Licensed Software
Article 9
Destruction of the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents
shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or
sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be
entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any
related documents.
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed
Software, any related documents and copies thereof within two (2) weeks from such date of termination.
Article 10
Protection of Copyright
1. The copyright and all the other intellectual property rights relating to the Licensed Software
shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the
ownership of the User.
Article 5
Indemnification of Licensor
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User
or any third party due to the exercise of the license granted to the User under this Agreement, unless
otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with
certain objective of the Licensed Software.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the
copyright and other intellectual property rights.
Article 11
Export Restriction
1. It is prohibited to export the Licensed Software and any related documents outside the country
of the User (including transmission thereof outside the country of the User via Internet of other
communication tools).
Article 6
Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any
other intellectual property right that was caused by the User's use of the Licensed Software, the User shall
settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any
inconvenience it may cause.
2. The User shall understand that the Licensed Software shall be subject to the export restrictions
adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and
domestic laws (including the export control regulation of the country of User and any other countries,
and any restrictions concerning the end-users, the use by end-users and importing countries to be
provided by the country of User and any other countries, and any other governmental authorities).
Article 7
Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof
or any other information to be granted under this Agreement, as well as the conditions of this Agreement
as has not yet entered the public domain, and shall not disclose or divulge the same to any third party
without approval of the Licensor.
Article 12
Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions
shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of
this Agreement shall be provided or settled upon good-faith consultation between the Licensor and
the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and
any dispute arising from, and relating to the rights and obligations under, this Agreement shall be
submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.
Article 8
Termination
In case the User falls under any of the events described in the following items, the Licensor may
immediately terminate this Agreement or claim that the User compensates for the damage incurred by the
Licensor due to such event:
(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment, provisional attachment,
provisional disposition or any other compulsory execution.
iii
-CMP
Important Notice concerning the Software
-jansson
The MIT License (MIT)
Copyright (c) 2014 Charles Gunyon
Copyright (c) 2009-2012 Petri Lehtinen <petri@digip.org>
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/ or sell copies of
the Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
-cJSON
Copyright (c) 2009 Dave Gamble
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/ or sell copies of
the Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
iv
Basic procedure
Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
Connect the wires properly. See “Wiring connection” on page 3.
Install the unit to your car. See the following “Installing the unit
(in-dash mounting)”.
Installation/Connection
1
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
2
3
4
5
6
Connect the terminal of the car battery.
Press BSRC to turn on the power.
WARNING
Detach the faceplate and reset the unit within 5 seconds. See “How to
reset” on page 4.
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• To prevent short circuit:
Installing the unit (in-dash mounting)
–
–
–
Insulate unconnected wires with vinyl tape.
Be sure to ground this unit to the car’s chassis again after installation.
Secure the wires with cable clamps and wrap vinyl tape around the
wires that comes into contact with metal parts to protect the wires.
CAUTION
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
Hook on the
top side
Dashboard of
your car
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
Bend the appropriate tabs to hold the
sleeve firmly in place.
• If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
2
Installing the unit (without mounting sleeve)
Wiring connection
1
2
Remove the mounting sleeve and trim plate from the unit.
Align the holes in the unit (on both sides) with the vehicle
mounting bracket and secure the unit with screws (commercially
available).
Antenna terminal
Fuse (10 A)
Use only the specified screws.
Using wrong screws might damage
the unit.
If no connections are made, do not
let the wire come out from the tab.
Car fuse box
Removing the unit
Ignition switch
Car fuse box
Battery
a Brown: To connect the
d Red: Ignition 12 V
e Yellow: Battery 12 V
f Black: Ground
KENWOOD navigation system,
refer your navigation manual
b Blue/white: To the power
control terminal when using
the optional power amplifier
or to the antenna control
terminal in the vehicle
c Light blue/yellow: To the
steering wheel remote control
adapter
g White ª, White/black ·:
Front speaker (left)
h Gray ª, Gray/black ·:
Front speaker (right)
Part list (supplied)
(A) Faceplate (×1)
(B) Trimplate (×1)
(C) Mounting sleeve (×1)
(D) Wiring harness (×1)
(E) Extraction key (×2)
i Green ª, Green/black ·:
Rear speaker (left)
j Purple ª, Purple/black ·:
Rear speaker (right)
3
Before Use
Basics
IMPORTANT
Faceplate
• To ensure proper use, please read through this Guide before using this
product. It is especially important that you read and observe Warnings and
Cautions in this Guide.
Volume knob
Loading slot
USB input
terminal
• Please keep the Guide in a safe and accessible place for future reference.
WARNING
Auxiliary
input jack
Do not operate any function that takes your attention away from safe
driving.
Detach button
Display window*
CAUTION
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent
accidents.
• Lower the volume before playing digital sources to avoid damaging the
speakers by the sudden increase of the output level.
* Only for illustration purpose.
Attach Detach
How to reset
Reset the unit
General:
within 5 seconds
after detaching the
faceplate.
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no
responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside
the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc
and wait for the moisture to evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate.
• Depending on the types of cars, the antenna will automatically extend
when you turn on the unit with the antenna control wire connected.
Turn off the unit or change the source to STANDBY when parking at a low
ceiling area.
To
On the faceplate
Turn on the power
Press BSRC.
• Press and hold to turn off the power.
Adjust the volume
Select a source
Turn the volume knob.
Press BSRC repeatedly.
Change the display information Press DISP repeatedly.
4
9
Turn the volume knob to select [DATE SET], then press the knob.
Getting Started
10 Turn the volume knob to make the settings, then press the knob.
Set the date in the order of “Day” “Month” “Year” or “Month” “Day”
“Year”.
1
Select the display language and cancel the
11 Press and hold
to exit.
demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to
To return to the previous setting item, press
.
[YES]), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB”
1
Turn the volume knob to select [ENG] (English) / [SPA] (Spanish) /
[FRE] (French), then press the knob.
[ENG] is selected for the initial setup.
3
Set the other optional settings
You can only set the following items while the unit is in STANDBY source.
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”.
Press the volume knob again.
[YES] is selected for the initial setup.
Press the volume knob again.
1
2
3
Press BSRC repeatedly to enter STANDBY.
Press the volume knob to enter [FUNCTION]
Turn the volume knob to select an item (see the following table), then
press the knob.
2
3
.
“DEMO OFF” appears.
4
5
Repeat step 3 until the desired item is selected or activated.
Press and hold
to exit.
To return to the previous setting item, press
.
2
Set the clock and date
1
2
Press the volume knob to enter [FUNCTION]
Turn the volume knob to select [CLOCK], then press the knob.
.
Default: [XX]
[SYSTEM]
To adjust the clock
3
4
[KEY BEEP]
[ON]: Activates the keypress tone. ; [OFF]: Deactivates.
Turn the volume knob to select [CLOCK ADJUST], then press the knob.
Turn the volume knob to make the settings, then press the knob.
Set the time in the order of “Hour” “Minute”.
Turn the volume knob to select [CLOCK FORMAT], then press the knob.
Turn the volume knob to select [12H] or [24H], then press the knob.
[FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ;
[NO]: Cancels.
5
6
[ENGLISH]
Select the display language for [FUNCTION] menu and music
To set the date
[ESPANOL]
[FRANCAIS]
information if applicable.
By default, [ENGLISH] is selected.
7
8
Turn the volume knob to select [DATE FORMAT], then press the knob.
Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press
the knob.
5
Radio
CD/USB/iPod
Search for a station
Start playback
1
2
3
Press BSRC repeatedly to select RADIO.
Press BAND repeatedly to select FM1/FM2/FM3/AM.
Press S / T to search for a station.
The source changes automatically and playback starts when you load a disc
or attach a device (USB device/ iPod/iPhone) to the USB input terminal.
To
On the faceplate
Press 6 IW.
Settings in memory
Play back/pause
Reverse/Fast-forward
Select a track/file
Select a folder
Repeat play
You can store up to 18 stations for FM and 6 stations for AM.
Press and hold
.
Store a station
While listening to a station....
Press and hold one of the number buttons (1 to 6).
Press
.
Press 2 / 1
.
Select a stored station
Press one of the number buttons (1 to 6).
Press 4
Press 3
repeatedly.
repeatedly.
Random play
6
Examples of some well-used settings
Functions Settings
Subwoofer Level Setting
1
2
3
4
Press the volume knob to enter [FUNCTION].
Turn the volume knob to select an item, then press the knob.
Repeat step 2 until the desired item is selected or activated.
1
2
Press the volume knob to enter [FUNCTION].
Press and hold
to exit.
Turn the volume knob to select [AUDIO CONTROL], then press the knob.
Turn the volume knob to select [SUBWOOFER SET], then press the knob.
Turn the volume knob to select [SW SET ON], then press the knob.
Turn the volume knob to select [SUB-W LEVEL], then press the knob.
To return to the previous setting item, press
.
• Refer to the INSTRUCTION MANUAL on the following website for the
detailed explanation of each item: <www.kenwood.com/cs/ce/>
• The availability of each item vary depending on the model.
3
4
5
6
[FUNCTION] menu items
[AUDIO CONTROL]
[DISPLAY]
[TUNER SETTING]
[USB]
[BT MODE]
[REMOTE APP]
[MIC GAIN]*
[NR LEVEL]*
[ECHO CANCEL]*
[SYSTEM]
[CLOCK]
[ENGLISH]
[ESPANOL]
[FRANCAIS]
[DEMO MODE]
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Sets your preferred audio settings.
Sets your preferred control for the display window.
Settings for radio source.
Settings for using a USB device.
Settings for using a Bluetooth device.
Settings for using smartphone to control this unit.
Sets the sensitivity of the microphone.
Adjusts the noise reduction level.
Adjusts the echo cancellation delay time.
Settings for this unit.
Turn the volume knob to adjust the subwoofer level, then press the
knob.
Adjusts the clock.
Selects language for the menu and music information.
Selects language for the menu and music information.
Selects language for the menu and music information.
Activates or deactivates the display demonstration.
7
Press and hold
to exit.
* Applicable only while talking on the phone.
Note:
You need to set [SWITCH PREOUT] to [SUB-W] in standby mode before you can
make the above settings.
7
Once pairing is completed, Bluetooth connection is established
automatically.
• “BT1” and/or “BT2” indicator on the display window lights up.
Bluetooth®
• Depending on the Bluetooth version, operating system and the
firmware version of your mobile phone, Bluetooth features may not
work with this unit.
• Be sure to turn on the Bluetooth function of the device to make the
following operations.
Answer a call
Press or the volume knob or one of the number buttons (1 to 6).
• To adjust the phone volume [00] to [35], turn the volume knob.
• To end a call, press
.
• Signal conditions vary depending on the surroundings.
Audio player via Bluetooth
Press BSRC repeatedly to select BT AUDIO.
• Pressing enters BT AUDIO directly.
Connect the microphone
Connect the supplied microphone to the microphone input jack on the rear
panel.
1
2
Operate the audio player via Bluetooth to start playback.
To
On the faceplate
Secure using cord
clamps (not supplied)
if necessary.
Adjust the
microphone
angle
Play back/pause
Press 6 IW.
Press 2 / 1
Press
Select group or folder
Reverse skip/Forward skip
Reverse/Fast-forward
Repeat play
.
.
Pair and connect a Bluetooth device for the first time
Press and hold
.
1
2
Press BSRC to turn on the unit.
Press 4 repeatedly.
Press and hold 3 to select [ALL RANDOM]
Search and select the name of your receiver (“KDC-BT278U”) on the
Bluetooth device.
“PAIRING” “PASS XXXXXX” “Device name” “PRESS” “VOLUME
Random play
or [GROUP RANDOM]
.
KNOB” appears on the display.
• For some Bluetooth devices, you may need to enter the Personal
Identification Number (PIN) code immediately after searching.
Press the volume knob to start pairing.
3
“PAIRING OK” appears when pairing is completed.
8
Other Information
For playback operations of AUX, Spotify, Pandora® sources, refer to the
INSTRUCTION MANUAL on the following website:
<www.kenwood.com/cs/ce/>
• The availability of each source vary depending on the model.
Note for specifications
Bluetooth Frequency Range:
2.402 GHz — 2.480 GHz
Bluetooth RF Output Power (E.I.R.P.):
+4 dBm (MAX), Power Class 2
Speaker Impedance:
4 Ω — 8 Ω
Operating Voltage:
12 V DC car battery
9
•
•
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect
wireless performance.
•
•
•
•
•
Apple, iPhone, iPod, iPod touch, and Lightning are trademarks of Apple Inc., registered in the U.S. and other countries.
Android is a trademark of Google LLC.
©2019 Pandora Media, LLC. All rights reserved. PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, LLC. Used with permission.
SPOTIFY and the Spotify logo are among the registered trademarks of Spotify AB.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those
of their respective owners.
|
Soleus Air Sg Wac 25hce User Manual
Ricoh Aficio Color 5560 User Manual
LG LWJ0514ACG User Manual
LG 65TR3PJ B User Manual
Heat Storm Heater User Manual
GE 18 User Manual
EPSON EB 84H User Manual
DELL S2317HJ User Manual
CRAFTSMAN 919.156730 User Manual
ACER ASPIRE R 13 User Manual