HP EliteBook 6930p Notebook PC
Maintenance and Service Guide
MSG revision history
Revision
Publication date
Description
A
November 2009
The part number has been updated to 593138-001 for the 90-W HP Smart AC
adapter for use in all countries and regions except India. The information was
B
September 2010
Updated spare part number 482959-001 (Audio/ExpressCard assembly) to indicate
the spare kit does not include the cable. The information was updated in the following
Updated spare part number 487432-001 (Cable Kit) to indicate the kit includes the
Audio/ExpressCard cable. The information was updated in the following locations:
Removed spare part number 593138-001 (90-W HP Smart AC adapter for use in all
countries and regions except India). The information was removed from the following
Updated the spare part numbers for the memory. The information was updated in the
Added spare part numbers for new display panels. The information was added in the
Added spare part numbers for new LED display bezels. The information was added in
Added spare part numbers for new system boards for Russia and the People's
Republic of China. The information was added in the following locations: Computer
Added spare part numbers for new WLAN modules. The information was added in
Added spare part numbers for new keyboards. The information was added in the
Added spare part numbers for new AC adapters. The information was added in the
Added a spare part number for a new capacitative board with cable. The information
iii
B (continued) September 2010
Added a spare part number for a new docking station. The information was added in
Updated the spare part number for the upgrade bay cradle from 502322-001 to
613682-001. The information was updated in the following locations: Computer
Updated the spare part numbers for various processors. The information was updated
Added a spare part number for a new top cover without fingerprint reader. The
information was added in the following locations: Computer major components
Updated and added spare part numbers for various new hard drives. The information
was updated and added in the following locations: Computer major components
Added spare part numbers for new batteries. The information was added in the
Updated the hard drive specifications in the following location: Hard drive
iv
MSG revision history
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to
contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer
and the AC adapter comply with the user-accessible surface temperature limits defined by the
International Standard for Safety of Information Technology Equipment (IEC 60950).
v
vi
Safety warning notice
Table of contents
1 Product description ........................................................................................................... 1
2 External component identification ..................................................................................... 9
3 Illustrated parts catalog .................................................................................................. 21
4 Removal and replacement procedures ............................................................................ 42
vii
6 Specifications ............................................................................................................... 109
14.1-inch, WXGA display specifications .................................................................................110
DVD-ROM Drive ...................................................................................................................114
System I/O address specifications ..........................................................................................117
System memory map specifications .........................................................................................119
7 Screw listing ................................................................................................................. 120
Phillips 2.5×9.0 captive screw ...............................................................................................124
8 Backup and recovery in Windows Vista ........................................................................ 137
Backing up your information ..................................................................................................139
Recovering individual files ......................................................................................142
ix
Recovering information using a Windows Vista operating system DVD (purchased
9 Backup and recovery in Windows XP ........................................................................... 147
10 Connector pin assignments ......................................................................................... 152
11 Power cord set requirements ...................................................................................... 157
12 Recycling .................................................................................................................... 159
x
1 Product description
Category
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
Product Name
Processors
HP EliteBook 6930p Notebook PC
Intel® Core™ 2 Duo processors
√
√
√
T9900 3.06-GHz processor, 6-MB
L2 cache, 1066-MHz front side
bus (FSB)
●
√
T9800 2.93-GHz processor, 6-MB
L2 cache, 1066-MHz FSB
●
●
√
√
√
√
T9600 2.80-GHz processor, 6-MB
L2 cache, 1066-MHz FSB
T9550 2.66-GHz processor, 6-MB
L2 cache, 1066-MHz FSB, 35W
●
●
√
√
√
√
T9400 2.53-GHz processor, 6-MB
L2 cache, 1066-MHz FSB, 35W
P9600 2.66-GHz processor, 6-MB
L2 cache, 1066-MHz FSB, 25W
●
●
●
●
●
√
√
√
√
√
√
√
√
√
√
P9500 2.53-GHz processor, 6-MB
L2 cache, 1066-MHz FSB, 25W
P8800 2.66-GHz processor, 3-MB
L2 cache, 1066-MHz FSB
P8700 2.53-GHz processor, 3-MB
L2 cache, 1066-MHz FSB
P8600 2.40-GHz processor, 3-MB
L2 cache, 1066-MHz FSB
●
P8400 2.26-GHz processor, 3-MB
L2 cache, 1066-MHz FSB
√
√
√
Chipset
Northbridge: Intel GM45 with up to
1067 FSB with iAMT support
Northbridge: Intel PM45 with up to
1067 FSB with iAMT support
√
√
Southbridge: Intel ICH9M enhanced
√
1
Category
Graphics
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
ATI M82-SCE Mobility Radeon HD
3450 discrete graphics subsystem
memory with 128 MB GDDR3
√
(operating at 700 MHz) or 256 MB
GDDR3 (operating at 700 MHz)
Mobile Intel GMA X4500 HD Universal
Memory Architecture (UMA) graphics
subsystem integrated with shared video
memory (dynamically allocated), up
to 384 MB
√
√
Panels
All display assemblies include 3
wireless local area network (WLAN)
antennae
√
Supports HP Panel Protection System
Supports HP privacy filter
√
√
√
√
Supports the following display assemblies:
●
●
●
14.1-inch WXGA LED
14.1-inch WXGA+
14.1-inch WXGA
√
√
√
√
√
√
√
√
Memory
2 customer-accessible/upgradable
memory module slots
Supports dual-channel memory
Supports up to 8 GB of system RAM
PC2-6400, 800-MHz, DDR2
√
√
√
√
√
√
2
Chapter 1 Product description
Category
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
Supports the following configurations in
all countries and regions except Brazil:
√
√
●
●
●
●
●
●
●
●
8192-MB total system memory
(4096 × 2, dual-channel)
4096-MB total system memory
(2048 × 2, dual-channel)
4096-MB total system memory
(4096 × 1)
3072-MB total system memory
(2048 + 1024, dual-channel)
2048-MB total system memory
(1024 × 2)
2048-MB total system memory
(2048 × 1)
1024-MB total system memory
(512 × 2, dual-channel)
1024-MB total system memory
(1024 × 1)
Supports the following configurations
only in Brazil:
√
√
●
●
●
●
●
4096-MB total system memory
(2048 × 2, dual-channel)
2048-MB total system memory
(1024 × 2, dual-channel)
2048-MB total system memory
(2048 × 1)
1024-MB total system memory
(512 × 2, dual-channel)
1024-MB total system memory
(1024 × 1)
Hard drives
Supports 9.5-mm (2.5-inch) hard drives
Customer-accessible
√
√
√
√
√
√
√
√
√
√
√
√
Serial ATA
Supports Disk Sanitizer
Supports full disk encryption
Supports HP 3D DriveGuard
3
Category
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
Supports RAID 0 (striping) and
RAID 1 (mirror)
√
√
√
√
Supports the following drives:
●
●
●
●
●
●
320-GB, 7200-rpm hard drive
250-GB, 7200-rpm hard drive
160-GB, 7200-rpm hard drive
120-GB, 7200-rpm hard drive
128-GB, solid-state drive
80-GB solid-state drive
Upgrade bay
Fixed (removal of 1 screw required)
Customer-accessible
√
√
√
√
√
√
√
√
√
√
√
√
Serial ATA
12.7-mm tray load
Supports weight saver option
Supports the following optical drives:
●
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive
with LightScribe
●
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive
●
●
DVD/CD-RW Combo Drive
DVD-ROM Drive
Supports the following hard drives
(requires the upgrade bay cradle):
√
√
●
●
250-GB, 5400-rpm
160-GB, 7200-rpm
Audio/video
HD audio
√
√
√
√
√
√
√
√
√
√
√
√
Integrated dual array microphones (2)
Stereo speakers (2)
Integrated 2-megapixel webcamera
56K V.92 1.5-inch data/fax modem
Support for no-modem option
Modem
4
Chapter 1 Product description
Category
Ethernet
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
Intel 82567LM 10/100/1000 Ethernet,
with iAMT Intel 82567LM Gigabit
network connection
√
√
S4/S5 wake on LAN: DC - no
S4/S5 wake on LAN: AC - yes
√
√
√
√
Wireless
Integrated WLAN options by way of wireless module:
3 WLAN antennae built into
display assembly
√
√
Support for no-WLAN option
√
√
√
√
Support for the following WLAN
formats:
●
●
●
●
Broadcom 4322 802.11a/b/g/n
Broadcom 4311AG 802.11a/b/g
Broadcom BCM4312 802.11b/g
Intel Wi-Fi Link 5300 802.11a/b/
g/n
●
Intel Wi-Fi Link 5100 802.11a/b/
g/n
●
Intel Wi-Fi Link 5100 802.11b/g
Integrated WWAN options by way of wireless module:
2 WWAN antennae built into
display assembly
√
√
√
Subscriber identity module (SIM) security
√
Integrated personal area network (PAN) options by way of Bluetooth® module:
Support for no-WPAN option
Broadcom Bluetooth 2.0+EDR
√
√
√
√
√
√
External media One ExpressCard/54 slot
cards
SD card reader supporting Secure
Digital (SD) Memory Card and
MultiMediaCard (MMC)
√
√
Ports
Audio-in (mono microphone)
Audio-out (stereo headphone)
Docking
√
√
√
√
√
√
5
Category
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
Battery (system)
Battery (travel)
RJ-11 (modem)
√
√
√
√
√
√
√
√
RJ-45 (Ethernet, includes link and
activity lights)
USB (3)
√
√
√
√
VGA (Dsub 15-pin) supporting 1600 ×
1200 external resolution at 75-GHz (hot
plug/unplug with auto-detect)
1394a
√
√
√
√
√
√
3-pin HP Smart AC Adapter
Keyboard/
pointing
devices
11.97-inch keyboard with embedded
numeric keypad
Spill-resistant keyboard
Dura-Keys
√
√
√
√
√
√
Vertical scrolling, taps enabled as
default
Dualpoint (pointing stick and TouchPad)
with 2 pointing stick buttons and 2
TouchPad buttons
√
√
√
√
Power
requirements
90-W HP Smart AC Adapter with
localized cable plug support (2-wire
plug with ground pin, supports 2-
pin DC connector)
120-W HP Smart AC Adapter with
localized cable plug support (2-wire
plug with ground pin, supports 2-
pin DC connector)
√
√
8-cell, 58-Wh Li-ion battery
6-cell, 55-Wh Li-ion battery
4-cell, 37-Wh Li-ion battery
√
√
√
√
√
√
√
√
Support for 12-cell Ultra
Capacity Battery
Support for 8-cell Li-ion Extended
Life Battery
√
√
√
√
HP Fast Charge Technology
6
Chapter 1 Product description
Category
Security
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
Supports Kensington security sock
√
√
√
√
Infineon Trusted Platform Module
(TPM) v. 1.2
TPM Enhanced Drive Lock
Fingerprint reader
√
√
√
√
√
√
Integrated smart card reader
Preinstalled:
Operating
system
Windows® Vista® Basic 32 with and
without Office Ready
√
√
√
√
√
√
Windows Vista Business 32 with and
without Office Ready
Windows Vista Ultimate with Office
Ready (in Canada and
the United States)
Windows Vista Business with
Windows® XP Pro with and without
Office Ready
√
√
Windows Vista Basic 32 with Office
Personal and Powerpoint (Japan)
√
√
√
√
√
√
√
√
√
√
√
√
Windows Vista Basic 32 with Office Pro
2007 (Japan)
Windows Vista Business 32 with Office
Personal and Powerpoint (Japan)
Windows Vista Business 32 with Office
Pro 2007 (Japan)
Windows Vista Business 32 with Office
Personal (Japan)
Windows Vista Business with Windows
XP Pro and Office Personal with
Powerpoint (Japan)
Windows Vista Business with Windows
XP Pro and Office Pro 2007 (Japan)
√
√
√
√
√
√
Windows Vista Business with Windows
XP Pro with Office Personal (Japan)
FreeDOS
Restore media:
7
Category
Description
Computer models
equipped with discrete
graphics subsystem
memory
Computer models
equipped with Unified
Memory Architecture
(UMA) graphics
subsystem memory
DRDVD Windows Vista
DRDVD Windows XP
Windows Vista Basic 32
Windows Vista Business 32
Windows Vista Business 64
Windows Vista Ultimate
Windows XP Pro
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Certified:
Microsoft® WHQL
Novell
√
√
√
√
√
√
SuSE Linux
Web support:
Windows Vista Enterprise 32
Windows Vista Enterprise 64
Windows XP Pro
√
√
√
√
√
√
Serviceability
Customer service replaceable (CSR) parts:
AC adapter
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Battery (system)
Expansion memory module
Hard drive
Keyboard
Optical drive
Primary memory module
SIM
WLAN module
WWAN module
8
Chapter 1 Product description
2 External component identification
Top components
Display
Item
(1)
Component
Function
Ambient light sensor
Automatically adjusts the display brightness based on the
lighting conditions in your environment.
(2)
(3)
(4)
(5)
Internal microphones (2)
HP Webcam
Record sound.
Records video and captures still video.
On: The integrated camera is in use.
HP Webcam light
Keyboard light
Illuminates the keyboard in low-light conditions when the
keyboard light button is pressed.
(6)
Keyboard light button
Opens and turns on the keyboard light.
Top components
9
Antennae
Item
(1)
Component
Description
WWAN antennae (2)*
Send and receive wireless signals to communicate with
wireless wide-area networks (WWAN).
(2)
WLAN antennae (3)*
Send and receive wireless signals to communicate with
wireless local area networks (WLAN).
*The antennae are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennae free from obstructions.
10
Chapter 2 External component identification
Button, switches, and fingerprint reader
Item
(1)
Component
Function
●
●
●
●
Power button
When the computer is off, press the button to turn on the
computer.
When the computer is on, press the button to shut down
the computer.
When the computer is in the Sleep state, press the button
briefly to exit Sleep.
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the computer.
To learn more about your power settings, select Start >
Control Panel > System and Maintenance >
Power Options.
(2)
(3)
(4)
Internal display switch
Info button
Turns off the display if the display is closed while the power
is on.
Launches Info center, which enables you to open various
software solutions.
Wireless button
Turns the wireless feature on or off but does not establish a
wireless connection.
NOTE: A wireless network must be set up in order to
establish a wireless connection.
(5)
(6)
Presentation button
Volume mute button
Starts the presentation feature.
Mutes and restores speaker sound.
Top components
11
Item
(7)
Component
Function
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to
decrease volume and to the right to increase volume. You can
also press the left side of the volume slider to decrease
volume, or press the right side of the volume slider to increase
volume.
(8)
Fingerprint reader (select models only)
Allows a fingerprint logon to Windows, instead of a
password logon.
Keys
Item
(1)
Component
Function
esc key
Displays system information when pressed in combination with
the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key or the esc key.
(3)
(4)
(5)
(6)
Windows logo key
Displays the Windows Start menu.
Windows applications key
Embedded numeric keypad keys
Function keys
Displays a shortcut menu for items beneath the pointer.
Can be used like the keys on an external numeric keypad.
Execute frequently used system functions when pressed in
combination with the fn key.
12
Chapter 2 External component identification
Lights
Item
(1)
Component
Function
●
Wireless lights (2)*
On: An integrated wireless device, such as a wireless
local area network (WLAN) device, the HP Broadband
Wireless Module, and/or a Bluetooth® device, is on.
●
●
●
●
Amber: All wireless devices are off.
On: The computer is on.
(2)
(3)
Power lights (2)†
Blinking: The computer is in the Sleep state.
Blinking rapidly: An AC adapter with a higher power
rating should be connected.
●
●
●
●
Off: The computer is off or in Hibernation.
Amber: A battery is charging.
Battery light
Green: A battery is close to full charge capacity.
Blinking amber: A battery that is the only available
power source has reached a low battery level. When the
battery reaches a critical battery level, the battery light
begins blinking rapidly.
●
Off: If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays off
until the battery reaches a low battery level.
●
●
(4)
Drive light
Blinking green: The hard drive or optical drive is
being accessed.
Amber: HP 3D DriveGuard has temporarily parked the
internal hard drive, and if present, the hard drive in the
upgrade bay.
Top components
13
Item
(5)
Component
Caps lock light
Num lock light
Function
On: Caps lock is on.
(6)
On: Num lock is on or the embedded numeric keypad
is enabled.
●
●
(7)
Volume mute light
On: Computer sound is on.
Amber: Computer sound is off.
(8)
(9)
Volume down light
Volume up light
Blinking: The volume scroll zone is being used to decrease
speaker volume.
Blinking: The volume scroll zone is being used to increase
speaker volume.
*The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open.
The wireless light on the front of the computer is visible whether the computer is open or closed.
†The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
Pointing devices
Item
Component
Function
(1)
(2)
(3)
(4)
(5)
(6)
Pointing stick
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Functions like the right button on an external mouse.
Scrolls up or down.
Left pointing stick button*
TouchPad*
Left TouchPad button*
Right pointing stick button*
TouchPad scroll zone
14
Chapter 2 External component identification
Front components
Item
(1)
Component
Function
Wireless light
On: An integrated wireless device, such as a wireless local
area network (WLAN) device, the HP Broadband Wireless
Module, and/ or a Bluetooth device, is on. Amber: All
wireless devices are off.
●
●
●
(2)
(3)
Power light
On: The computer is on.
Blinking: The computer is in the Sleep state.
Blinking rapidly: An AC adapter with a higher power
rating should be connected.
●
●
●
●
Off: The computer is off or in Hibernation.
Amber: A battery is charging.
Battery light
Green: A battery is close to full charge capacity.
Blinking amber: A battery that is the only available
power source has reached a low battery level. When the
battery reaches a critical battery level, the battery light
begins blinking rapidly.
●
Off: If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays off
until the battery reaches a low battery level.
(4)
(5)
Drive light
Blinking green: The hard drive or optical drive is being
accessed. Amber: HP 3D DriveGuard has temporarily parked
the hard drive.
SD card reader
Supports the Secure Digital (SD) Memory Card and
MultiMediaCard (MMC) optional digital card formats.
(6)
(7)
(8)
Speakers (2)
Produce sound.
Display release button
Bluetooth compartment
Opens the computer.
Contains a Bluetooth device.
16
Chapter 2 External component identification
Rear components
Item
(1)
Component
Description
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a deterrent,
but it may not prevent the computer from being mishandled
or stolen.
(2)
(3)
Power connector
Connects an AC adapter.
External monitor port
Connects an external VGA monitor or projector.
Right-side components
Item
(1)
Component
Function
Smart card reader
Upgrade bay
Supports optional smart cards and Java™ cards.
Supports an optical drive or hard drive.
Connects an optional USB device.
Connects a network cable.
(2)
(3)
USB port
(4)
RJ-45 (network) jack
RJ-11 (modem) jack
(5)
Connects a modem cable.
Rear components
17
Left-side components
Item
(1)
Component
Function
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for
the internal fan to cycle on and off during routine operation.
(2)
(3)
USB ports (2)
1394 port
Connect optional USB devices.
Connects an optional IEEE 1394 or 1394a device, such as
a camcorder.
(4)
(5)
Audio-in (microphone) jack
Audio-out (headphone) jack
Connects an optional computer headset microphone, stereo
array microphone, or monaural microphone.
Produces sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television
audio.
(6)
ExpressCard slot
Supports optional ExpressCards.
18
Chapter 2 External component identification
Bottom components
Item
(1)
Component
Battery bay
Function
Holds the battery.
(2)
Docking connector
Vents (5)
Connects an optional docking device.
Enable airflow to cool internal components.
(3)
CAUTION: To prevent overheating, do not obstruct vents.
Use the computer only on a hard, flat surface. Do not allow
another hard surface, such as an adjoining optional printer, or
a soft surface, such as pillows or thick rugs or clothing, to
block airflow.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for
the internal fan to cycle on and off during routine operation.
(4)
(5)
(6)
(7)
Accessory battery connector
Memory module compartment
Hard drive bay
Connects an optional accessory battery.
Contains the expansion memory module slot.
Holds the hard drive.
WWAN module compartment
Contains a WWAN module (select models only).
CAUTION: To prevent an unresponsive system and the
display of a warning message, replace the device with only a
WLAN module authorized for use in the computer by the
governmental agency that regulates wireless devices in your
country. If you replace the device and then receive a warning
message, remove the device to restore computer functionality,
and then contact technical support through Help and Support.
Bottom components
19
3 Illustrated parts catalog
Serial number location
The service tag, affixed to the bottom of the computer, provides information that may be needed when
troubleshooting system problems. The service tag provides the following information:
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
(3) Part number/Product number (p/n): This number provides specific information about the product's
hardware components. The part number helps a service technician to determine what components and
parts are needed.
(4) Model description: This is the number used to locate documents, drivers, and support for the
computer.
(5) Warranty period: Describes the duration of the warranty period for the computer.
When ordering parts or requesting information, provide the computer serial number and model
description provided on the service tag.
Serial number location
21
Item
(1)
Description
Spare part number
14.1-inch, AntiGlare display assemblies (include three WLAN antenna cables, two WWAN antenna
cables, and two microphones):
WXGA LED display assembly with webcam (includes webcam cable)
WXGA LED display assembly without webcam
487433-001
483202-001
487435-001
483201-001
487434-001
483200-001
WXGA+ display assembly with webcam (includes webcam cable)
WXGA+ display assembly without webcam
WXGA display assembly with webcam (includes webcam cable)
WXGA display assembly without webcam
Display assembly internal components:
Display bezels
For use only with computer models equipped with non-LED displays and a webcam
488189-001
For use only with computer models equipped with non-LED displays without a webcam 488190-001
For use only with computer models equipped with LED displays and a webcam
For use only with computer models equipped with LED displays without a webcam
518420-001
518421-001
486302-001
Webcam
Display panels
WXGA display panel
WXGA LED display panel
WXGA+ display panel
623154-001
623155-001
623156-001
487431-001
482967-001
482966-001
500325-001
482969-001
Display inverter
Display Hinge Kit (includes left and right hinges)
Display Cable Kit (includes display panel cable)
Logo Kit
Wireless Antenna Kit (includes 3 WLAN antenna transceivers and cables and 2
WWAN antenna transceivers and cables)
(2)
Switch cover (includes capacitative board and cable)
486307-001
Capacitative board (includes cable; not illustrated)
487428-001
(3)
Power button board (includes cable)
482964-001
(4a)
Keyboards (include keyboard cable, keyboard shield, pointing stick, and pointing stick cable)
For use in Belgium
483010-A41
For use in Brazil
483010-201
483010-221
483010-081
For use in the Czech Republic
For use in Denmark
Computer major components
23
Item
Description
Spare part number
For use in Europe, the Middle East, and Africa
483010-021
For use in France
483010-051
483010-121
483010-041
483010-DJ1
483010-211
483010-DD1
483010-BB1
483010-061
483010-291
483010-161
483010-B31
483010-091
483010-131
483010-251
483010-171
483010-B71
483010-231
483010-BA1
For use in French Canada
For use in Germany
For use in Greece
For use in Hungary
For use in Iceland
For use in Israel
For use in Italy
For use in Japan
For use in Latin America
For use in the Netherlands
For use in Norway
For use in Portugal
For use in Russia
For use in Saudi Arabia
For use in Sweden and Finland
For use in Slovakia
For use in Slovenia
For use in South Korea
483010-AD1
483010-071
483010-BG1
483010-AB1
483010-141
483010-031
483010-001
For use in Spain
For use in Switzerland
For use in Taiwan
For use in Turkey
For use in the United Kingdom
For use in the United States
(4b)
Keyboard shield (included with keyboard spare part kit)
Pointing stick rubber caps (not illustrated)
Fan
486565-001
487436-001
(5)
(6)
Heat sinks (include replacement thermal material)
For use only with computer models with discrete graphics subsystem memory
For use only with computer models with UMA graphics subsystem memory
483011-001
483012-001
24
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
487429-001
part information):
(7a)
(7b)
(7c)
(7d)
(7e)
ExpressCard slot bezel
Hard drive bay cover
Memory module compartment cover
Bluetooth module compartment cover
WWAN module compartment cover
Cable Kit:
487432-001
(8a)
(8b)
Bluetooth module cable
Modem module cable (includes RJ-11 connector)
Audio board cable (not illustrated)
(9)
Intel Core 2 Duo processors (include replacement thermal material)
T9900, 3.06-GHz (1066-MHz FSB, 6-MB L2 cache)
570434-001
507951-001
507955-002
507953-001
507956-002
507957-001
507958-001
570036-001
507960-001
507963-002
507964-002
T9800, 2.93-GHz (1066-MHz FSB, 6-MB L2 cache)
T9600, 2.80-GHz (1066-MHz FSB, 6-MB L2 cache)
T9550, 2.66-GHz (1066-MHz FSB, 6-MB L2 cache, 35W)
T9400, 2.53-GHz (1066-MHz FSB, 6-MB L2 cache, 35W)
P9600, 2.66-GHz (1066-MHz FSB, 3-MB L2 cache, 25W)
P9500, 2.53-GHz (1066-MHz FSB, 6-MB L2 cache, 25W)
P8800, 2.66-GHz (1066-MHz FSB, 3-MB L2 cache)
P8700, 2.53-GHz (1066-MHz FSB, 3-MB L2 cache)
P8600, 2.40-GHz (1066-MHz FSB, 3-MB L2 cache)
P8400, 2.26-GHz (1066-MHz FSB, 3-MB L2 cache)
(10)
(11)
Primary memory modules (PC2-6400, 800-MHz, DDR2)
598855-001
4096-MB
2048-MB
598858-001
598861-001
1024-MB
Modem modules
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is
included in the Cable Kit, spare part number 487432-001. See Cable Kit on page 31 for more Cable Kit spare
part information.
For use in all countries and regions except Australia and New Zealand
For use only in Australia and New Zealand
WLAN modules
461750-001
461750-011
(12)
Computer major components
25
Item
Description
Spare part number
Intel Wi-Fi Link 5300 802.11a/b/g/n WLAN module for use in all
countries and regions
480986-001
Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all
countries and regions
480985-001
482957-001
Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use in all
countries and regions
Broadcom 4322 802.11a/b/g/n WLAN modules:
●
●
For use in Antigua and Barbuda, Barbados, Belize, Canada,
the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago,
the U.S. Virgin Islands, and the United States
487330-001
487330-002
For use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria,
Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Broadcom BCM4312 802.11b/g WLAN modules:
●
For use in Antigua and Barbuda, Barbados, Belize, Canada,
the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago,
the U.S. Virgin Islands, and the United States
459263-001
26
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola,
459263-002
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria,
Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Intel Wi-Fi Link 5100 802.11a/b/g/n 1x2 WLAN module with iAMT 4.0 support for
use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong,
India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan,
Uruguay, the United States, Venezuela, and Vietnam
506678-001
506679-001
Intel Wi-Fi Link 5300 802.11a/b/g/n 3x3 WLAN module with iAMT 4.0 support for
use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong,
India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan,
Uruguay, the United States, Venezuela, and Vietnam
Intel 802.11a/b/g WLAN module for use in Russia, Ukraine, and Pakistan
506680-001
(13)
(14)
RTC battery
482963-001
Top cover (includes smart card reader and TouchPad buttons)
With fingerprint reader
486303-001
Without fingerprint reader
611810-001
(15)
(16)
TouchPad (includes cable and TouchPad button board and cable)
486306-001
486309-001
Fingerprint reader board (includes cable)
Computer major components
27
Item
(17)
Description
Spare part number
Audio/ExpressCard assembly (includes ExpressCard slot, cable, headphone and 482959-001
microphone connectors, and SD card reader slot)
NOTE: The Audio/ExpressCard assembly spare part kit does not include an audio
cable. The Audio/ExpressCard assembly cable is included in the Cable Kit, spare part
information.
(18)
(19)
Speaker
486308-001
System boards (include replacement thermal material)
For use in all countries and regions except for Russia and the People's Republic of
China
●
●
●
For use only with computer models with discrete graphics subsystem memory
(includes 256 MB of graphics subsystem memory
486300-001
486299-001
486301-001
For use only with computer models with discrete graphics subsystem memory
(includes 128 MB of graphics subsystem memory
For use only with computer models with UMA graphics subsystem memory
For use in only in Russia and the People's Republic of China
For use only with computer models with discrete graphics subsystem memory
(includes 256 MB of graphics subsystem memory
510352-001
510351-001
510353-001
●
●
●
For use only with computer models with discrete graphics subsystem memory
(includes 128 MB of graphics subsystem memory
For use only with computer models with UMA graphics subsystem memory
(20)
Batteries
8-cell, 58-Wh Li-ion battery for use only in Japan
6-cell, 62-Wh Li-ion battery for use only in Japan
534063-291
534218-291
482962-001
482961-001
482960-001
482968-001
6-cell, 55-Wh Li-ion battery
4-cell, 37-Wh Li-ion battery
Base enclosure
(21)
(22)
Rubber Kit (not illustrated, includes base enclosure rubber feet and rubber
screw covers)
Optical drives (include bezel and bracket)
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
515874-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
DVD/CD-RW Combo Drive
483190-001
483189-001
483191-001
613682-001
DVD-ROM Drive
Upgrade bay device cradle
Hard drives (include bracket)
320-GB, 7200-rpm
(23)
531969-001
28
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
250-GB, 7200-rpm
495059-001
160-GB, 7200-rpm
483186-001
483184-001
575554-001
120-GB, 7200-rpm
128-GB solid-state drive (not illustrated)
80-GB solid-state drive (not illustrated)
486304-001
(24)
External memory modules (PC2-6400, 800-MHz, DDR2)
598855-001
598858-001
598861-001
483113-001
4096-MB
2048-MB
1024-MB
(25)
(26)
Bluetooth module
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module
cable. The Bluetooth module cable is included in the Cable Kit, spare part number
HP un2400 Mobile Broadband WWAN module
483377-001
Computer major components
29
Plastics Kit
Item
Description
Spare part number
Plastics Kit:
487429-001
(1)
(2)
(3)
(4)
(5)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
Memory module compartment cover (includes one captive screw, secured by a C-clip)
ExpressCard slot bezel
WWAN module compartment cover (includes one captive screw, secured by a C-clip)
Bluetooth module compartment cover (includes one captive screw, secured by a C-clip)
30
Chapter 3 Illustrated parts catalog
Mass storage devices
Item
Description
Spare part number
(1)
Hard drives (include bracket)
320-GB, 7200-rpm
531969-001
495059-001
483186-001
483184-001
250-GB, 7200-rpm
160-GB, 7200-rpm
120-GB, 7200-rpm
(2)
Optical drives (include bezel and bracket)
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
515874-001
483190-001
483189-001
483191-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
DVD/CD-RW Combo Drive
DVD-ROM Drive
(3)
Solid-state drives
128-GB
575554-001
80-GB
486304-001
613682-001
Upgrade bay device cradle (not illustrated)
32
Chapter 3 Illustrated parts catalog
Miscellaneous parts
Description
Docking station
AC adapters
Spare part number
483203-001
Smart Adapter, 90-W PFC AC adapter for use only in India
535593-001
620656-001
613160-001
613153-001
463956-001
613154-001
463953-001
Smart Adapter, 90-W PFC, RC/V 3W
Smart Adapter, 90-W PFC, RC/V EM 3W for use only in India
Smart Adapter, 90-W PFC, RC/V 3W
Smart Adapter, 90-W, for use only in India
Smart Adapter, 120-W PFC, RC/V 3W
Smart Adapter, 120-W PFC, 3P/RC
Power cords:
For use in Argentina
490371-D01
490371-011
490371-201
490371-021
490371-BB1
490371-D61
490371-061
490371-291
490371-AA1
490371-AR1
490371-AD1
490371-111
490371-AB1
490371-031
490371-001
For use in Australia
For use in Brazil
For use in Europe, the Middle East, and Africa
For use in Iceland
For use in India
For use in Italy
For use in Japan
For use in the People's Republic of China
For use in South Africa
For use in South Korea
For use in Switzerland
For use in Taiwan
For use in the United Kingdom
For use in the United States
Miscellaneous parts
33
Description
Screw Kit
Spare part number
486305-001
●
●
●
●
●
●
●
●
●
●
●
Phillips PM3.0×4.0 screw
Phillips PM2.5×11.0 captive screw
Phillips PM2.5×10.0 captive screw
Phillips PM2.5×9.0 captive screw
Phillips PM2.5×7.0 screw
Phillips PM2.5×4.0 screw
Phillips PM2.0×5.0 captive screw
Phillips PM2.0×5.0 screw
Phillips PM2.0×3.0 broad-head screw
Phillips PM2.0×3.0 screw
Torx T8M2.5×7.0 screw
Travel battery
456946-001
34
Chapter 3 Illustrated parts catalog
Sequential part number listing
Spare part
number
Description
456946-001
459263-001
Travel battery
Broadcom BCM4312 802.11b/g WLAN module for use in Antigua and Barbuda, Barbados, Belize,
Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands,
and the United States
459263-002
Broadcom BCM4312 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas,
Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
461750-001
461750-011
Modem module for use in all countries and regions except Australia and New Zealand
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
Cable Kit spare part information.
Modem module for use only in Australia and New Zealand
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
Cable Kit spare part information.
463953-001
463956-001
480985-001
480986-001
482957-001
482959-001
Smart Adapter, 120-W PFC, 3P/RC
Smart Adapter, 90-W, for use only in India
Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions
Intel Wi-Fi Link 5300 802.11a/b/g/n WLAN module for use in all countries and regions
Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use in all countries and regions
Audio/ExpressCard assembly (includes ExpressCard slot, cable, headphone and microphone connectors,
and SD card reader slot)The Audio/ExpressCard assembly spare part kit does not include an audio
cable. The Audio/ExpressCard assembly cable is included in the Cable Kit, spare part number
Sequential part number listing
35
Spare part
number
Description
482960-001
482961-001
482962-001
482963-001
482964-001
482966-001
482967-001
482968-001
Base enclosure
4-cell, 37-Wh Li-ion battery
6-cell, 55-Wh Li-ion battery
RTC battery
Power button board (includes cable)
Display Cable Kit (includes display panel cable)
Display Hinge Kit (includes left and right hinges)
Rubber Kit (includes base enclosure rubber feet, rubber screw covers, and display bezel rubber
screw covers)
482969-001
Wireless Antenna Kit (includes 3 WLAN antenna transceivers and cables and 2 WWAN antenna
transceivers and cables)
483010-001
483010-021
483010-031
Keyboard for use in the United States (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
Keyboard for use in Europe, the Middle East, and Africa (includes keyboard cable, keyboard shield,
pointing stick, and pointing stick cable)
Keyboard for use in the United Kingdom (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
483010-041
483010-051
483010-061
483010-071
483010-081
483010-091
483010-121
483010-131
483010-141
483010-161
483010-171
Keyboard for use in Germany (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in France (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Italy (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Spain (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Denmark (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in Norway (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in French Canada (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
Keyboard for use in Portugal (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Turkey (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Latin America (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
Keyboard for use in Saudi Arabia (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
36
Chapter 3 Illustrated parts catalog
Spare part
number
Description
483010-201
483010-211
483010-221
483010-231
483010-251
483010-281
483010-291
483010-A41
483010-AB1
Keyboard for use in Brazil (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Hungary (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in the Czech Republic (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
Keyboard for use in Slovakia (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in Russia (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Thailand (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in Japan (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Belgium (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Taiwan (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
483010-AD1
483010-BA1
483010-B31
Keyboard for use in South Korea (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in the Slovenia (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in the Netherlands (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
483010-B71
483010-BB1
483010-BG1
483010-DD1
483010-DJ1
483011-001
483012-001
Keyboard for use in Sweden and Finland (includes keyboard cable, keyboard shield, pointing stick, and
pointing stick cable)
Keyboard for use in Israel (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Switzerland (includes keyboard cable, keyboard shield, pointing stick, and pointing
stick cable)
Keyboard for use in Iceland (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Keyboard for use in Greece (includes keyboard cable, keyboard shield, pointing stick, and pointing stick
cable)
Heat sink for use only with computer models with discrete graphics subsystem memory (includes
replacement thermal material)
Heat sink for use only with computer models with UMA graphics subsystem memory (includes
replacement thermal material)
Sequential part number listing
37
Spare part
number
Description
483113-001
Bluetooth module
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 487432-001. See Cable Kit on page 31
for more Cable Kit spare part information.
483184-001
483186-001
483189-001
483190-001
483191-001
483200-001
120-GB, 7200-rpm hard drive (includes bracket)
160-GB, 7200-rpm hard drive (includes bracket)
DVD/CD-RW Combo Drive
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
DVD-ROM Drive
14.1-inch, WXGA AntiGlare display assembly for use on computer models not equipped with a webcam
(includes three WLAN antenna cables, two WWAN antenna cables, and two microphones)
483201-001
483202-001
14.1-inch, WXGA+ AntiGlare display assembly for use on computer models not equipped with a
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two microphones)
14.1-inch, WXGA AntiGlare LED display assembly for use on computer models not equipped with a
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two microphones)
483203-001
483377-001
486299-001
Docking station
HP un2400 Mobile Broadband WWAN module
System board with 128 MB of discrete graphics subsystem memory for use in all countries and regions
except for Russia and the People's Republic of China (includes replacement thermal material)
486300-001
486301-001
System board with 256 MB of discrete graphics subsystem memory for use in all countries and regions
except for Russia and the People's Republic of China (includes replacement thermal material)
System board for use only with computer models with UMA graphics subsystem memory for use in all
countries and regions except for Russia and the People's Republic of China (includes replacement
thermal material)
486302-001
486303-001
486304-001
486305-001
486306-001
486307-001
486308-001
486309-001
486565-001
487330-001
Webcam
Top cover with fingerprint reader (includes TouchPad buttons)
80-GB solid-state drive
Screw Kit
TouchPad (includes cable and TouchPad button board and cable)
Switch cover (includes capacitative board and cable)
Speaker
Fingerprint reader board (includes cable)
Pointing stick rubber caps
Broadcom 4322 802.11a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize,
Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands,
and the United States
38
Chapter 3 Illustrated parts catalog
Spare part
number
Description
487330-002
Broadcom 4322 802.11a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas,
Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
487428-001
487429-001
487431-001
487432-001
487433-001
Capacitative board (includes cable)
Display inverter
14.1-inch, WXGA AntiGlare LED display assembly for use on computer models equipped with a webcam
(includes three WLAN antenna cables, two WWAN antenna cables, and two microphones)
487434-001
487435-001
14.1-inch, WXGA AntiGlare display assembly for use on computer models equipped with a webcam
(includes three WLAN antenna cables, two WWAN antenna cables, and two microphones)
14.1-inch, WXGA+ AntiGlare display assembly for use on computer models equipped with a webcam
(includes three WLAN antenna cables, two WWAN antenna cables, and two microphones)
487436-001
488189-001
488190-001
490371-001
490371-011
490371-021
490371-031
490371-061
490371-111
490371-201
Fan
Display bezel for use only with computer models equipped with non-LED displays and a webcam
Display bezel for use only with computer models equipped with non-LED displays without a webcam
Power cord for use in the United States
Power cord for use in Australia
Power cord for use in Europe, the Middle East, and Africa
Power cord for use in the United Kingdom
Power cord for use in Italy
Power cord for use in Switzerland
Power cord for use in Brazil
Sequential part number listing
39
Spare part
number
Description
490371-291
490371-AA1
490371-AB1
490371-AD1
490371-AR1
490371-BB1
490371-D01
490371-D61
495059-001
500325-001
502322-0001
506678-001
Power cord for use in Japan
Power cord for use in the People's Republic of China
Power cord for use in Taiwan
Power cord for use in South Korea
Power cord for use in South Africa
Power cord for use in Iceland
Power cord for use in Argentina
Power cord for use in India
250-GB, 7200-rpm hard drive (includes bracket)
Logo Kit
Upgrade bay device cradle
Intel Wi-Fi Link 5100 802.11a/b/g/n 1x2 WLAN module with iAMT 4.0 support for use in Antigua and
Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the Cayman Islands,
Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti,
Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia,
Taiwan, Uruguay, the United States, Venezuela, and Vietnam
506679-001
Intel Wi-Fi Link 5300 802.11a/b/g/n 3x3 WLAN module with iAMT 4.0 support for use in Antigua and
Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the Cayman Islands,
Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti,
Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia,
Taiwan, Uruguay, the United States, Venezuela, and Vietnam
506680-001
507951-001
Intel 802.11a/b/g WLAN module for use in Russia, Ukraine, and Pakistan
Intel Core 2 Duo T9800, 2.93-GHz processor (1066-MHz FSB, 6-MB L2 cache, includes replacement
thermal material)
507953-001
507955-002
Intel Core 2 Duo T9550, 2.66-GHz processor (1066-MHz FSB, 6-MB L2 cache, 35W, includes
replacement thermal material)
Intel Core 2 Duo T9600, 2.80-GHz processor (1066-MHz FSB, 6-MB L2 cache, includes replacement
thermal material)
507956-002
Intel Core 2 Duo T9400, 2.53-GHz processor (1066-MHz FSB, 6-MB L2 cache, 35W, includes
replacement thermal material)
507957-001
507958-001
507960-001
507963-002
Intel Core 2 Duo P9600, 2.66-GHz processor (1066-MHz FSB, 3-MB L2 cache, 25W, includes
replacement thermal material)
Intel Core 2 Duo P9500, 2.53-GHz processor (1066-MHz FSB, 6-MB L2 cache, 25W, includes
replacement thermal material)
Intel Core 2 Duo P8700, 2.53-GHz processor (1066-MHz FSB, 3-MB L2 cache, includes replacement
thermal material)
Intel Core 2 Duo P8600, 2.40-GHz processor (1066-MHz FSB, 3-MB L2 cache, includes replacement
thermal material)
507964-002
Intel Core 2 Duo P8400, 2.26-GHz processor (1066-MHz FSB, 3-MB L2 cache, includes replacement
thermal material)
40
Chapter 3 Illustrated parts catalog
Spare part
number
Description
510351-001
510352-001
510353-001
System board with 128 MB of discrete graphics subsystem memory for use only in Russia and the
People's Republic of China (includes replacement thermal material)
System board with 256 MB of discrete graphics subsystem memory for use only in Russia and the
People's Republic of China (includes replacement thermal material)
System board for use only in computer models with UMA graphics subsystem memory for use only in
Russia and the People's Republic of China (includes replacement thermal material)
515874-001
518420-001
518421-001
531969-001
534063-291
534218-291
535593-001
570036-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
Display bezel for use only with computer models equipped with LED displays that include a webcam
Display bezel for use only with computer models equipped with LED displays without a webcam
320-GB, 7200-rpm hard drive (includes bracket)
8-cell, 58-Wh Li-ion battery for use only in Japan
6-cell, 62-Wh Li-ion battery for use only in Japan
Smart Adapter, 90-W PFC, for use only in India
Intel Core 2 Duo P8800, 2.66-GHz processor (1066-MHz FSB, 3-MB L2 cache, includes replacement
thermal material)
570434-001
Intel Core 2 Duo T9900, 3.06-GHz processor (1066-MHz FSB, 6-MB L2 cache, includes replacement
thermal material)
575554-001
598855-001
598858-001
598861-001
611810-001
128-GB solid-state drive
4096-MB memory module (PC2-6400, 800-MHz, DDR2)
2048-MB memory module (PC2-6400, 800-MHz, DDR2)
1024-MB memory module (PC2-6400, 800-MHz, DDR2)
Top cover without fingerprint reader (includes TouchPad buttons)
Smart Adapter, 90-W PFC, RC/V 3W
Smart Adapter, 120-W PFC, RC/V 3W
Smart Adapter, 90-W PFC, RC/V EM 3W for use only in India
Upgrade bay device cradle
613153-001
613154-001
613160-001
613682-001
620656-001
623154-001
623155-001
623156-001
Smart Adapter, 90-W PFC, RC/V 3W
WXGA display panel
WXGA LED display panel
WXGA+ display panel
Sequential part number listing
41
4 Removal and replacement
procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
●
●
●
Flat-bladed screwdriver
Magnetic screwdriver
Phillips P0 and P1 screwdrivers
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
42
Chapter 4 Removal and replacement procedures
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with
extreme care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
Preliminary replacement requirements
43
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some
protection, but in many cases, ESD contains enough power to alter device parameters or melt
silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
15,000 V
5,000 V
800 V
55%
Walking across carpet
35,000 V
12,000 V
6,000 V
7,500 V
3,000 V
400 V
Walking across vinyl floor
Motions of bench worker
Removing DIPS from plastic tube
Removing DIPS from vinyl tray
Removing DIPS from Styrofoam
Removing bubble pack from PCB
Packing PCBs in foam-lined box
2,000 V
700 V
400 V
11,500 V
14,500 V
26,500 V
21,000 V
4,000 V
5,000 V
20,000 V
11,000 V
2,000 V
3,500 V
7,000 V
5,000 V
44
Chapter 4 Removal and replacement procedures
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
●
●
●
●
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
Place items on a grounded surface before removing items from their containers.
Always be properly grounded when touching a component or assembly.
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials
are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●
●
Cover the workstation with approved static-shielding material.
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
●
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting or removing connectors or test equipment.
Preliminary replacement requirements
45
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips must
be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
●
●
●
●
●
●
●
●
●
●
●
Antistatic tape
Antistatic smocks, aprons, and sleeve protectors
Conductive bins and other assembly or soldering aids
Nonconductive foam
Conductive tabletop workstations with ground cords of one megohm resistance
Static-dissipative tables or floor mats with hard ties to the ground
Field service kits
Static awareness labels
Material-handling packages
Nonconductive plastic bags, tubes, or boxes
Metal tote boxes
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
1,500 V
Antistatic plastic
Carbon-loaded plastic
Metallized laminate
Bags
Floor mats
Floor mats
7,500 V
5,000 V
46
Chapter 4 Removal and replacement procedures
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the
password:
NOTE: These steps also clear CMOS.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
6. Wait approximately 5 minutes.
7. Replace the RTC battery and reassemble the computer.
8. Connect AC power to the computer. Do not reinsert any batteries at this time.
9. Turn on the computer.
All passwords and all CMOS settings have been cleared.
Preliminary replacement requirements
47
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 72 screws, in 12 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Service tag
The service tag, affixed to the bottom of the computer, provides information that may be needed when
troubleshooting system problems. The service tag provides the following information:
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
(3) Part number/Product number (p/n): This number provides specific information about the product's
hardware components. The part number helps a service technician to determine what components and
parts are needed.
(4) Model description: This is the number used to locate documents, drivers, and support for the
computer.
(5) Warranty period: Describes the duration of the warranty period for the computer.
48
Chapter 4 Removal and replacement procedures
Battery
Description
Spare part number
534063-291
8-cell, 58-Wh Li-ion battery for use only in Japan
6-cell, 62-Wh Li-ion battery for use only in Japan
6-cell, 55-Wh Li-ion battery
534218-291
482962-001
4-cell, 37-Wh Li-ion battery
482961-001
Before disassembling the computer, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch (1) to release the battery.
3. Remove the battery (2) from the computer.
Install the battery by inserting it into the battery bay until you hear a click.
50
Chapter 4 Removal and replacement procedures
SIM
NOTE: This section applies only to computer models with WWAN capability. If there is a SIM
inserted in the SIM slot, it should be removed before disassembling the computer. Be sure the SIM is
reinserted in the SIM slot after reassembling the computer.
Before removing the SIM, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the SIM:
1. Press in on the SIM (1). (The module is partially ejected from the SIM slot.)
2. Remove the SIM (2) from the SIM slot.
Reverse this procedure to install the SIM.
Component replacement procedures
51
Display inverter
Description
Spare part number
Display inverter
487431-001
Before removing the display inverter, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the display inverter:
1. Turn the computer right-side up, with the front toward you.
2. Open the computer as far as it will open.
3. Remove the two rubber screw covers (1) on the bottom edge of the display bezel. The rubber
screw covers are available in the Display Rubber Kit, spare part number 482966-001.
4. Remove the two Phillips PM2.5×6.0 screws (2) that secure the bottom edge of the display bezel to
the display enclosure.
5. Flex the hinge cover areas (1) and the bottom edge (2) of the display bezel until the bezel
disengages from the display enclosure.
52
Chapter 4 Removal and replacement procedures
6. Release the bottom edge of the display bezel (3) from the display assembly.
7. Release the zero insertion force (ZIF) connector (1) to which the keyboard light cable is attached,
and disconnect the keyboard light cable from the display inverter.
8. Remove the two Phillips PM2.5×4.0 screws (2) that secure the display inverter to the display
enclosure.
9. Release the display inverter (3) from the display enclosure as far as the display panel cable and
backlight cable allow.
10. Disconnect the display panel cable (4) and the backlight cable (5) from the display inverter.
11. Remove the display inverter.
Reverse this procedure to install the display inverter.
Component replacement procedures
53
Bluetooth module
NOTE: The Bluetooth® module spare part kit does not include a Bluetooth module cable. The
Bluetooth module cable is included in the Cable Kit, spare part number 487432-001. See Bluetooth
module cable on page 95 for removal procedures for the Bluetooth module cable.
Description
Spare part number
Bluetooth module
483113-001
Before removing the Bluetooth module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the Bluetooth module:
1. Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the Bluetooth module compartment
cover to the computer.
2. Remove the Bluetooth module compartment cover (2) by lifting it straight up.
NOTE: The Bluetooth module compartment cover is included in the Plastics Kit, spare part
number 487429-001.
3. Release the Bluetooth module (1) from the computer as far as the Bluetooth module cable allows.
54
Chapter 4 Removal and replacement procedures
4. Disconnect the Bluetooth module cable (2) from the Bluetooth module.
5. Remove the Bluetooth module.
Reverse this procedure to install the Bluetooth module.
Component replacement procedures
55
Hard drive
NOTE: All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
531969-001
320-GB, 7200-rpm
250-GB, 7200-rpm
160-GB, 7200-rpm
495059-001
483186-001
120-GB, 7200-rpm
483184-001
575554-001
486304-001
128-GB solid-state drive
80-GB solid-state drive
Before removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the hard drive:
1. Position the computer with the front toward you.
2. Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the hard drive bay cover to the
computer.
56
Chapter 4 Removal and replacement procedures
3. Lift the left side of the hard drive bay cover (2), swing it up and to the right, and remove the
cover. The hard drive bay cover is included in the Plastics Kit, spare part number 487429-001.
4. Loosen the Phillips PM2.5×10.0 captive screw (1) that secures the hard drive to the computer.
5. Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) to the right to disconnect it
from the system board.
6. Remove the hard drive (4) from the hard drive bay.
7. If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive
bracket screws (1) from each side of the hard drive.
Component replacement procedures
57
Optical drive
NOTE: All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
515874-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
DVD/CD-RW Combo Drive
483190-001
483189-001
DVD-ROM Drive
483191-001
Before removing the optical drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the optical drive:
1. Position the computer with the front toward you.
2. Loosen the Phillips PM2.5×9.0 captive screw (1) that secures the optical drive to the computer.
3. Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (2) and press the
tab to the left to release the optical drive from the computer.
4. Remove the optical drive (3) from the upgrade bay.
5. If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward
you.
Component replacement procedures
59
6. Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
7. Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install an optical drive.
Upgrade bay device
Description
Spare part number
Upgrade bay device cradle
502322-001
Before removing the upgrade bay device, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the upgrade bay device:
1. Position the computer with the front toward you.
2. Loosen the Phillips PM2.5×9.0 captive screw (1) that secures the upgrade bay device to the
computer.
3. Remove the four Phillips PM2.5×4.0 screws (2) that secure the upgrade bay device to the
computer.
4. Insert a flat-bladed screwdriver or similar tool into the upgrade bay device tab access (3) and
press the tab to the left to release the upgrade bay device from the computer.
60
Chapter 4 Removal and replacement procedures
5. Remove the upgrade bay device (4) from the computer.
6. If it is necessary to remove the hard drive from the upgrade bay cradle, position the upgrade bay
cradle with the front bezel toward you.
7. Loosen the Phillips PM2.5×10.0 captive screw (1) that secures the hard drive to the upgrade bay
cradle.
8. Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) forward to disconnect it
from the upgrade bay cradle.
9. Remove the hard drive (4) from the upgrade bay cradle.
Reverse this procedure to install the upgrade bay device.
Component replacement procedures
61
Expansion memory module
Description
Spare part number
598855-001
4096-MB memory module (PC2-6400, 800-MHz, DDR2)
2048-MB memory module (PC2-6400, 800-MHz, DDR2)
1024-MB memory module (PC2-6400, 800-MHz, DDR2)
598858-001
598861-001
Before removing the expansion memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the memory module:
1. Position the computer with the front toward you.
2. Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the memory module compartment
cover to the computer.
3. Lift the left side of the cover (2), swing it up and to the right, and remove the cover. The memory
module compartment cover is included in the Plastics Kit, spare part number 487429-001.
4. Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
62
Chapter 4 Removal and replacement procedures
5. Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install the expansion memory module.
WWAN module
Description
Spare part number
HP un2400 Mobile Broadband WWAN module
483377-001
Before removing the WWAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the WWAN module:
1. Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the WWAN module compartment
cover to the computer.
Component replacement procedures
63
2. Lift the left side of the cover (2), swing it up and to the right, and remove the cover. The WWAN
module compartment cover is included in the Plastics Kit, spare part 487429-001.
3. Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module.
NOTE: The red WWAN antenna cable is connected to the WWAN module “Main” terminal.
The blue WWAN antenna cable is connected to the WWAN module “Aux” terminal.
4. Remove the two Phillips PM2.5×4.0 screws (2) that secure the WWAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
5. Remove the WWAN module (3) by pulling the module away from the slot at an angle.
NOTE: WWAN modules are designed with a notch (4) to prevent incorrect insertion into the
WWAN module slot.
Reverse this procedure to install the WWAN module.
64
Chapter 4 Removal and replacement procedures
Keyboard
NOTE: All keyboard spare part kits include a keyboard cable, keyboard shield, pointing stick, and
pointing stick cable.
Country or region
Belgium
Spare part number
Country or region
Norway
Spare part number
483010-091
483010-A41
483010-201
483010-221
483010-081
483010-021
Brazil
Portugal
483010-131
The Czech Republic
Denmark
Russia
483010-251
Saudi Arabia
Sweden and Finland
483010-171
Europe, the Middle East, and
Africa
483010-B71
France
483010-051
483010-121
483010-041
483010-DJ1
483010-211
483010-DD1
483010-BB1
483010-061
483010-291
483010-161
483010-B31
Slovakia
483010-231
Slovenia
483010-BA1
French Canada
Germany
South Korea
Spain
483010-AD1
483010-071
483010-BG1
483010-AB1
483010-281
483010-141
483010-031
483010-001
Greece
Hungary
Switzerland
Taiwan
Iceland
Israel
Thailand
Italy
Turkey
Japan
The United Kingdom
The United States
Latin America
The Netherlands
Pointing stick rubber caps
486565-001
Before removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the keyboard:
1. Position the computer with front toward you.
Component replacement procedures
65
2. Loosen the three Phillips PM2.5×9.0 captive screws that secure the keyboard to the computer.
3. Turn the computer display-side up, with the front toward you.
4. Open the computer as far as possible.
5. Slide the four keyboard retention tabs (1) toward you. The tabs are located between the esc and
f1 keys, between the f4 and f5 keys, between the f8 and f9 keys, and between the f12 and scroll
keys.
6. Lift the rear edge of the keyboard (2), and swing it up and forward until it rests upside down on
the palm rest.
7. Release the ZIF connector (1) to which the pointing stick cable is attached, and disconnect the
pointing stick cable (2) from the system board.
66
Chapter 4 Removal and replacement procedures
8. Release the ZIF connector (3) to which the keyboard cable is attached, and disconnect the
keyboard cable (4) from the system board.
9. Remove the keyboard.
Reverse this procedure to install the keyboard.
Primary memory module
Description
Spare part number
598855-001
4096-MB memory module (PC2-6400, 800-MHz, DDR2)
2048-MB memory module (PC2-6400, 800-MHz, DDR2)
1024-MB memory module (PC2-6400, 800-MHz, DDR2)
598858-001
598861-001
Before removing the primary memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the primary memory module:
1. Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
Component replacement procedures
67
2. Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install the primary memory module.
68
Chapter 4 Removal and replacement procedures
Modem module
NOTE: The modem module spare part kits do not include a modem module cable. The modem
module cable is included in the Cable Kit, spare part number 487432-001.
Description
Spare part number
461750-001
For use in all countries and regions except Australia and New Zealand
Modem module for use only in Australia and New Zealand
461750-011
Before removing the modem module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the modem module:
1. Remove the two Phillips PM2.5×4.0 screws (1) that secure the modem module to the system
board.
2. Release the modem module (2) from the computer as far as the modem module cable allows.
3. Disconnect the modem module cable (3) from the modem module.
4. Remove the modem module.
Reverse this procedure to install the modem module.
Component replacement procedures
69
WLAN module
Description
Spare part number
480986-001
Intel Wi-Fi Link 5300 802.11a/b/g/n WLAN module for use in all countries and regions
Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions
Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use in all countries and regions
Broadcom 4322 802.11a/b/g/n WLAN modules:
480985-001
482957-001
●
For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
487330-001
487330-002
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji,
Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan,
Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Broadcom BCM4312 802.11b/g WLAN modules:
●
For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
459263-001
70
Chapter 4 Removal and replacement procedures
Description
Spare part number
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji,
Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
459263-002
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan,
Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Intel Wi-Fi Link 5100 802.11a/b/g/n 1x2 WLAN module with iAMT 4.0 support for use in
Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada,
the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El
Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States, Venezuela, and
Vietnam
506678-001
506679-001
506680-001
Intel Wi-Fi Link 5300 802.11a/b/g/n 3x3 WLAN module with iAMT 4.0 support for use in
Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada,
the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El
Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States, Venezuela, and
Vietnam
Intel 802.11a/b/g WLAN module for use in Russia, Ukraine, and Pakistan
Before removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Component replacement procedures
71
Remove the WLAN module:
1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal. If the computer is
equipped with an 802.11a/b/g/n WLAN module, the yellow WLAN antenna cable (2) is
connected to the middle terminal on the WLAN module.
2. Remove the two Phillips PM2.5×4.0 screws (3) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
3. Remove the WLAN module (4) by pulling the module away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (5) to prevent incorrect insertion into the
WLAN module slot.
Reverse this procedure to install the WLAN module.
72
Chapter 4 Removal and replacement procedures
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all
passwords and CMOS settings to be cleared.
Description
Spare part number
RTC battery
482963-001
Before removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the RTC battery:
1. Disconnect the RTC battery cable (1) from the system board.
2. Remove the RTC battery (2) from the clip built into the top cover.
Reverse this procedure to install the RTC battery.
Component replacement procedures
73
Switch cover
Description
Spare part number
Switch cover (includes capacitative board and cable)
486307-001
Capacitative board (includes cable)
487428-001
Before removing the switch cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the switch cover:
1. Close the computer and turn it upside down, with the rear panel toward you.
2. Remove the following:
(1) Two rubber screw covers. Screw covers are available in the Rubber Kit, spare part number
482966-001.
(2) Three Torx T8M2.5×7.0 screws.
(3) Two Phillips PM2.0×4.0 broad-head screws.
3. Turn the computer display-side up, with the front toward you.
4. Open the computer as far as possible.
74
Chapter 4 Removal and replacement procedures
5. Lift the right side of the keyboard shield (1) until it rests at an angle, and then remove the shield
(2) by lifting it straight up.
NOTE: The keyboard shield is included with the keyboard spare part kit.
6. Release the ZIF connector (1) to which the power button board cable is attached, and disconnect
the power button board cable from the system board.
7. Release the ZIF connector (2) to which the LED board cable is attached, and disconnect the LED
board cable from the system board.
8. Remove the switch cover by lifting it straight up (3).
Reverse this procedure to install the switch cover.
Component replacement procedures
75
Power button board
Description
Spare part number
Power button board (includes cable)
482964-001
Before removing the power button board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
Remove the power button board:
1. Turn the switch cover upside down, with the front toward you.
2. Remove the Phillips PM2.0×4.0 screw (1) that secures the power button board to the switch cover.
3. Lift the right side of the power button board (2) until it rests at an angle.
4. Remove the power button board (3) by sliding the board to the right at an angle.
Reverse this procedure to install the power button board.
76
Chapter 4 Removal and replacement procedures
Fan
Description
Spare part number
Fan
487436-001
Before removing the fan, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the fan:
1. Disconnect the fan cable (1) from the system board.
2. Remove the Phillips PM2.5×7.0 screw (2) that secures the fan to the base enclosure.
3. Lift the front edge of the fan (3) until it rests at an angle.
4. Remove the fan (4) by sliding it forward at an angle.
Reverse this procedure to install the fan.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side
of the computer.
Component replacement procedures
77
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is
designed to turn on automatically when high temperature conditions exist. These conditions are affected
by high external temperatures, system power consumption, power management/battery conservation
configurations, battery fast charging, and software requirements. Exhaust air is displaced through the
ventilation grill located on the left side of the computer.
Heat sink
NOTE: The heat sink spare part kits include replacement thermal material.
Description
Spare part number
483011-001
For use only with computer models with discrete graphics subsystem memory
For use only with computer models with UMA graphics subsystem memory
483012-001
Before removing the heat sink, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
5. Remove the following.
Remove the heat sink:
NOTE: Steps 1 through 5 apply only to computer models equipped with discrete graphics subsystem
memory. See steps 6 through 8 for removing the heat sink on computer models with UMA graphics
subsystem memory.
1. Following the 1, 2, 3, 4 sequence stamped into the heat sink, loosen the four Phillips PM2.5×11.0
captive screws (1) that secure the heat sink to the system board.
78
Chapter 4 Removal and replacement procedures
2. Remove the Phillips PM2.5×4.0 screw (2) that secures the heat sink to the system board.
3. Lift the right side of the heat sink (1) until it rests at angle.
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to detach
it.
4. Release the heat sink (2) by sliding it to the right until it clears the left side of the top cover.
Component replacement procedures
79
5. Remove the heat sink (3) by sliding it up and forward.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and
the system board each time the heat sink is removed. Thermal paste is used on the processor (1)
and the section of the heat sink (1) that services it. Thermal pads are used on the Northbridge
chip (2) and the section of the heat sink (2) that services it, and on the graphics subsystem chip
(3) and the section of the heat sink (3) that services it. Replacement thermal material is included
with all heat sink, system board, and processor spare part kits.
NOTE: Steps 6 through 8 apply only to computer models equipped with UMA graphics
subsystem memory. See steps 1 through 5 for removing the heat sink on computer models with
discrete graphics subsystem memory.
80
Chapter 4 Removal and replacement procedures
6. Following the 1, 2, 3, 4, sequence stamped into the heat sink, loosen the four Phillips
PM2.5×11.0 screws (1) that secure the heat sink to the system board.
7. Lift the right side of the heat sink (1) until it rests at an angle.
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to detach
it.
8. Release the heat sink (2) by sliding it to the right until it clears the left side of the top cover.
Component replacement procedures
81
9. Remove the heat sink (3) by sliding it up and forward.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and
the system board each time the heat sink is removed. Thermal paste is used on the processor (1)
and the section of the heat sink (1) that services it. Thermal pads are used on the Northbridge
chip (2) and the section of the heat sink (2) that services it. Replacement thermal material is
included with all heat sink, system board, and processor spare part kits.
Reverse this procedure to install the heat sink.
82
Chapter 4 Removal and replacement procedures
Processor
NOTE: All processor spare part kits include replacement thermal material.
Description
Spare part number
570434-001
Intel Core 2 Duo T9900, 3.06-GHz processor (1066-MHz FSB, 6-MB L2 cache)
Intel Core 2 Duo T9800, 2.93-GHz processor (1066-MHz FSB, 6-MB L2 cache)
Intel Core 2 Duo T9600, 2.80-GHz processor (1066-MHz FSB, 6-MB L2 cache)
Intel Core 2 Duo T9550, 2.66-GHz processor (1066-MHz FSB, 6-MB L2 cache, 35W)
Intel Core 2 Duo T9400, 2.53-GHz processor (1066-MHz FSB, 6-MB L2 cache, 35W)
Intel Core 2 Duo P9600, 2.66-GHz processor (1066-MHz FSB, 3-MB L2 cache, 25W)
Intel Core 2 Duo P9500, 2.53-GHz processor (1066-MHz FSB, 6-MB L2 cache, 25W)
Intel Core 2 Duo P8800, 2.66-GHz processor (1066-MHz FSB, 3-MB L2 cache)
Intel Core 2 Duo P8700, 2.53-GHz processor (1066-MHz FSB, 3-MB L2 cache)
Intel Core 2 Duo P8600, 2.40-GHz processor (1066-MHz FSB, 3-MB L2 cache)
507951-001
507955-002
507953-001
507956-002
507957-001
507958-001
570036-001
507960-001
507963-002
507964-002
Intel Core 2 Duo P8400, 2.26-GHz processor (1066-MHz FSB, 3-MB L2 cache)
Before removing the processor, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
5. Remove the following:
Remove the processor:
1. Use a flat-bladed screwdriver to turn the processor locking screw (1) one-half turn
counterclockwise until you hear a click.
Component replacement procedures
83
2. Lift the processor (2) straight up and remove it.
NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned
with the triangle (4) embossed on the processor slot.
Reverse this procedure to install the processor.
84
Chapter 4 Removal and replacement procedures
Display assembly
Description
Spare part number
14.1-inch, WXGA AntiGlare LED display assembly for use on computer models equipped with a
487433-001
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two
microphones)
14.1-inch, WXGA AntiGlare LED display assembly for use on computer models not equipped
with a webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two
microphones)
483202-001
487435-001
14.1-inch, WXGA+ AntiGlare display assembly for use on computer models equipped with a
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two
microphones)
14.1-inch, WXGA+ AntiGlare display assembly for use on computer models not equipped with a 483201-001
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two
microphones)
14.1-inch, WXGA AntiGlare display assembly for use on computer models equipped with a
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two
microphones)
487434-001
14.1-inch, WXGA AntiGlare display assembly for use on computer models not equipped with a
webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two
microphones)
483200-001
Before removing the display assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the display assembly:
1. Close the computer and turn it upside down, with the rear panel toward you.
Component replacement procedures
85
2. Remove the following:
(1) Two round rubber screw covers. Screw covers are available in the Rubber Kit, spare part
number 482966-001.
(2) Two wedge-shaped rubber screw covers. Screw covers are available in the Rubber Kit, spare
part number 482966-001.
(3) Four Torx T8M2.5×7.0 screws that secure the display assembly to the computer.
3. Turn the computer right-side up, with the front toward you.
4. Open the computer as far as possible.
5. Disconnect the display panel cable (1) from the system board.
6. Disconnect the microphone cable (2) from the system board.
7. Remove the wireless antenna cables (3) from the clips and routing channels built into the top
cover.
8. Disconnect the webcam cable (1) from the system board.
86
Chapter 4 Removal and replacement procedures
9. Remove the wireless antenna cables (2) from the clips and routing channels built into the top
cover.
CAUTION: The display assembly will be unsupported when the following screws are removed.
To prevent damage to the display assembly, support it before removing the screws.
10. Remove the two T8M2.5×7.0 screws (1) that secure the display assembly to the computer.
11. Remove the display assembly (2) by lifting it straight up.
Component replacement procedures
87
12. If it is necessary to replace the display bezel or display hinges, remove the four rubber screw
covers (1) and the four Phillips PM2.5×7.0 screws (2) that secure the display bezel to the display
assembly. The rubber screw covers are available in the Rubber Kit, spare part number
482966-001.
13. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display
bezel until the bezel disengages from the display enclosure.
14. Remove the display bezel (3). The display bezel is available using spare part numbers:
●
●
488189-001 (for use in computer models equipped with non-LED displays and a webcam)
488190-001 (for use in computer models equipped with non-LED displays without a
webcam)
●
●
518420-001 (for use in computer models equipped with LED displays and a webcam)
518421-001 (for use in computer models equipped with LED displays without a webcam)
88
Chapter 4 Removal and replacement procedures
15. If it is necessary to replace the display hinges, remove the two Phillips PM2.5×7.0 screws (1) that
secure the display hinges to the display enclosure.
16. Remove the display hinges (2). The left and right display hinges are included in the Display Hinge
Kit, spare part number 482967-001.
The display panel is available using the following spare part numbers:
●
●
●
623154-001 (for use in computer models equipped with WXGA displays)
623155-001 (for use in computer models equipped with WXGA LED displays)
623156-001 (for use in computer models equipped with WXGA+ displays)
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures
89
Top cover
Description
Spare part number
Top cover with fingerprint reader (includes TouchPad buttons)
486303-001
Top cover without fingerprint reader (includes TouchPad buttons)
611810-001
Before removing the top cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
5. Remove the following:
Remove the top cover:
1. Turn the computer upside down, with the front toward you.
90
Chapter 4 Removal and replacement procedures
2. Remove the following:
(1) Two round rubber screw covers on the front edge of the base enclosure. Rubber screw covers
are available in the Rubber Kit, spare part number 482968-001.
(2) Two cup-shaped rubber screw covers on the right edge of the base enclosure. Rubber screw
covers are available in the Rubber Kit, spare part number 482968-001.
(3) Seven Torx8 T8M2.5×7.0 screws.
(4) One Phillips PM2.0×5.0 screw.
3. Turn the computer right-side up, with the front toward you.
4. Release the ZIF connector (1) to which the TouchPad cable is attached, and disconnect the
TouchPad cable from the system board.
5. Release the ZIF connector (2) to which the audio/ExpressCard assembly cable is attached, and
disconnect the audio/ExpressCard assembly cable from the system board.
6. Release the ZIF connector (3) to which the fingerprint reader board cable is attached, and
disconnect the fingerprint reader board cable from the system board.
7. Lift the rear edge of the top cover (1) until it detaches from the base enclosure.
Component replacement procedures
91
8. Remove the top cover (2) by lifting it straight up.
Reverse this procedure to install the top cover.
TouchPad
Description
Spare part number
TouchPad (includes cable and TouchPad button board and cable)
486306-001
Before removing the TouchPad, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
5. Remove the following:
Remove the TouchPad:
1. Turn the top cover upside down, with the front toward you.
2. Remove the four Phillips PM2.0×3.0 screws (1) that secure the TouchPad bracket to the top cover.
92
Chapter 4 Removal and replacement procedures
3. Release the TouchPad bracket (2) by sliding it toward the back of the top cover.
4. Remove the TouchPad bracket (3) by lifting it straight up.
5. Release the ZIF connector (1) to which the TouchPad button board cable is attached, and
disconnect the TouchPad button board cable from the TouchPad board.
6. Remove the TouchPad board (2) by lifting it straight up.
Reverse this procedure to install the TouchPad.
Component replacement procedures
93
Fingerprint reader board
Description
Spare part number
Fingerprint reader board (includes cable)
486309-001
Before removing the fingerprint reader board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
5. Remove the following:
Remove the fingerprint reader board:
1. Remove the fingerprint reader board cable (1) from the opening in the top cover.
2. Remove the fingerprint reader board (2) by lifting it straight up. The fingerprint reader board is
attached to the top cover using double-sided tape.
94
Chapter 4 Removal and replacement procedures
Reverse this procedure to install the fingerprint reader board.
Bluetooth module cable
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 487432-001.
Before removing the Bluetooth module cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
5. Remove the following:
Remove the Bluetooth module cable:
1. Disconnect the Bluetooth module cable (1) from the system board.
2. Detach the Bluetooth module cable (2) from the speaker. The Bluetooth module cable is attached
to the speaker using double-sided tape.
Reverse this procedure to install the Bluetooth module cable.
Component replacement procedures
95
Speaker
Description
Spare part number
Speaker
486308-001
Before removing the speaker, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
5. Remove the following:
Remove the speaker:
1. Disconnect the speaker cable (1) from the system board.
2. Remove the Torx8 T8M2.5×7.0 screw (2) that secures the speaker to the base enclosure.
96
Chapter 4 Removal and replacement procedures
3. Remove the speaker (3) by lifting it straight up.
Reverse this procedure to install the speaker.
Audio/ExpressCard assembly
NOTE: The Audio/ExpressCard assembly spare part kit does not include an audio cable. The Audio/
ExpressCard assembly cable is included in the Cable Kit, spare part number 487432-001. See Cable
Kit on page 31 for more Cable Kit spare part information.
Description
Spare part number
Audio/ExpressCard assembly (includes ExpressCard slot, cable, headphone and microphone
connectors, and SD card reader slot)
482959-001
Before removing the audio/ExpressCard assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
5. Remove the following:
Component replacement procedures
97
Remove the audio/ExpressCard assembly:
1. Release the ZIF connector (1) to which the audio/ExpressCard assembly cable is attached, and
disconnect the audio/ExpressCard assembly cable from the system board.
2. Lift the right side of the audio/ExpressCard assembly (2) to disconnect it from the system board.
3. Remove the audio/ExpressCard assembly (3) by sliding it up and to the right.
Reverse this procedure to install the audio/ExpressCard assembly.
Modem module cable
NOTE: The modem module spare part kits do not include a modem module cable. The modem
module cable is included in the Cable Kit, spare part number 487432-001. The modem module cable
includes an RJ-11 connector.
Before removing the modem module cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC Adapter from the computer.
98
Chapter 4 Removal and replacement procedures
5. Remove the following:
Remove the modem module cable:
1. Disconnect the modem module cable (1) from the system board.
2. Remove the RJ-11 connector (2) from the clip built into the base enclosure.
Reverse this procedure to install the modem module cable.
Component replacement procedures
99
System board
NOTE: All system board spare part kits include replacement thermal material.
Description
Spare part number
System board for use in all countries and regions except for Russia and the People's Republic of China
For use only with computer models with discrete graphics subsystem memory (includes 256 MB of
graphics subsystem memory
486300-001
486299-001
486301-001
For use only with computer models with discrete graphics subsystem memory (includes 128 MB of
graphics subsystem memory
For use only with computer models with UMA graphics subsystem memory
System board for use in only in Russia and the People's Republic of China
For use only with computer models with discrete graphics subsystem memory (includes 256 MB of
graphics subsystem memory
510352-001
510351-001
510353-001
For use only with computer models with discrete graphics subsystem memory (includes 128 MB of
graphics subsystem memory
For use only with computer models with UMA graphics subsystem memory
Before removing the system board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
5. Remove the following components:
100
Chapter 4 Removal and replacement procedures
i.
j.
When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●
●
●
●
●
●
●
●
Remove the system board:
1. Disconnect the modem module cable (1) from the system board.
2. Remove the three Phillips PM2.5×4.0 screws (2) that secure the system board to the base
enclosure.
NOTE: Computer models equipped with UMA graphics subsystem memory will have a fourth
Phillips PM2.5×4.0 screw (3) securing the system board to the base enclosure.
3. Use the optical drive connector (1) to lift the right edge of the system board (2) until it rests at an
angle.
Component replacement procedures
101
4. Remove the system board (3) from the base enclosure by sliding it up and to the right at an angle.
Reverse the preceding procedure to install the system board.
102
Chapter 4 Removal and replacement procedures
5 Computer Setup
This user guide describes features that are common to most models. Some features may not be
available on your computer.
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system
is not working or will not load.
NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your
computer.
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup
only if USB legacy support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and
System Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
Starting Computer Setup
103
NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the
keyboard to navigate and make selections in Computer Setup.
●
●
●
To select a menu or a menu item, use the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
To scroll up and down, click the plus sign (+) or the minus sign (-) in the upper-right corner of
the screen.
To close open dialog boxes and return to the main Computer Setup screen, press esc, and
then follow the on-screen instructions.
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup menus, choose one of the following methods:
●
To exit Computer Setup menus without saving your changes, click Exit in the lower-left corner of
the screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Ignore changes and exit, and then press enter.
– or –
●
To save your changes and exit Computer Setup menus, click Save in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click Save in the lower-left corner of the screen, and then follow
the on-screen instructions.
– or –
Use the arrow keys to select File > Save changes and exit, and then press enter.
104
Chapter 5 Computer Setup
Your changes go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory
settings.
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your
computer.
File menu
Select
To do this
●
●
System Information
View identification information for the computer and the batteries in the system.
View specification information for the processor, cache and memory size, system
ROM, video revision, and keyboard controller version.
Restore defaults
Replace the configuration settings in Computer Setup with the original factory settings.
(Password settings and security settings are not changed when you restore the factory
settings.)
Ignore changes and exit
Save changes and exit
Cancel any changes entered during the current session. Then exit and restart the computer.
Save changes and exit Save any changes entered during the current session. Then exit and
restart the computer. Your changes go into effect when the computer restarts.
Security menu
NOTE: Some of the menu items listed in this section may not be supported by your computer.
Select
To do this
Setup BIOS Administrator
Password
Set up a BIOS administrator password.
●
●
User Management (requires a
BIOS administrator password)
Create a new BIOS user account.
View a list of ProtectTools users.
Password Policy (requires a BIOS Revise password policy criteria.
administrator password)
HP SpareKey
Enable/disable HP SpareKey (enabled by default).
Always Prompt for HP SpareKey
Enrollment
Enable/disable HP SpareKey enrollment (enabled by default).
Enable/disable the fingerprint reader (select models only; disabled by default).
Enable/disable reset of HP ProtectTools security keys.
Fingerprint Reset on Reboot (if
Present)
Allow reset of HP ProtectTools
security keys
Computer Setup menus
105
Select
To do this
Change Password
HP SpareKey Enrollment
Enter, change, or delete a BIOS administrator password.
Enroll or reset HP SpareKey, which is a set of security questions and answers used if you
forget your password.
●
●
DriveLock Passwords
Enable/disable DriveLock on any computer hard drive (enabled by default).
Change a DriveLock user password or master password.
NOTE: DriveLock settings are accessible only when you enter Computer Setup by turning
on (not restarting) the computer.
Automatic DriveLock
Disk Sanitizer
Enable/disable Automatic DriveLock support.
Run Disk Sanitizer to destroy all existing data on the primary hard drive.
CAUTION: If you run Disk Sanitizer, the data on the primary hard drive is destroyed
permanently.
System IDs
Enter a user-defined computer asset tracking number and ownership tag.
Enable/disable a prompt for HP SpareKey enrollment.
Always Prompt for HP SpareKey
Enrollment
Diagnostics menu
Select
To do this
●
System Diagnostics menu
F1 System Information—Displays the following information:
◦
◦
Identification information for the computer and the batteries in the system.
Specification information for the processor, cache and memory size, system
ROM, video revision, and keyboard controller version.
●
●
●
F2 Start-up Test—Verifies the system components needed for starting the computer.
F3 Run-In Test—Runs a comprehensive check on system memory.
F4 Hard Disk Test—Runs a comprehensive self-test on any hard drive in the system.
106
Chapter 5 Computer Setup
System Configuration menu
NOTE: Some of the menu items listed in this section may not be supported by your computer.
Select
To do this
Language
Boot Options
Change the Computer Setup language.
●
●
●
●
●
●
●
Set a Startup Menu delay (in seconds).
Enable/disable Custom Logo (disabled by default).
Enable/disable Display Diagnostic URL (disabled by default).
Enable/disable CD-ROM boot (enabled by default).
Enable/disable SD Card boot (enabled by default).
Enable/disable diskette boot (enabled by default).
Enable/disable boot from Extensible Firmware Interface (EFI) File (select models only;
enabled by default).
●
Enable/disable internal network adapter boot and set the Preboot eXecution
Environment (PXE) (enabled by default).
●
●
●
Set the Express Boot Popup delay in seconds.
Set the boot order.
Device Configurations
Enable/disable USB legacy support (enabled by default). When enabled, USB legacy
support allows the following:
◦
Use of a USB keyboard in Computer Setup even when a Windows® operating
system is not running.
◦
Startup from bootable USB devices, including a hard drive, diskette drive, or
optical drive connected by a USB port to the computer.
●
Select a parallel port mode: ECP (Enhanced Capabilities Port), standard, bidirectional,
or EPP (Enhanced Parallel Port).
●
●
●
Enable/disable BIOS DMA data transfers (select models only; enabled by default).
Enable/disable fan always on while connected to an AC outlet (disabled by default).
Enable/disable LAN Power Save. When enabled, saves power by turning off the LAN
when not in use (enabled by default).
●
●
Enable/disable Data Execution Prevention. When enabled, the processor can disable
some virus code execution, which helps to improve computer security.
SATA (Serial Advanced Technology Attachment) device mode. The following options
are available:
◦
◦
◦
AHCI (Advanced Host Controller Interface)
IDE (Integrated Drive Electronics)
RAID (Redundant Array of Independent Disks)
Computer Setup menus
107
Select
To do this
NOTE: Availability of the options above varies by computer model.
●
●
●
●
Enable/disable secondary battery fast charge (enabled by default).
Enable/disable HP QuickLook (enabled by default).
Enable/disable Virtualization Technology (select models only; enabled by default).
Enable/disable TXT (Intel® Trusted Execution Technology) (select models only;
enabled by default).
●
●
●
Enable/disable Dual Core CPU (select models only; enabled by default).
Enable/disable the wireless button state (enabled by default).
Built-In Device Options
Enable/disable embedded WWAN device radio (select models only; enabled by
default).
●
●
●
Enable/disable embedded Bluetooth® device radio (enabled by default).
Enable/disable the Network Interface Controller (LAN) (enabled by default).
Set the wake on LAN state. Options include the following:
◦
◦
◦
Disabled
Boot to Network (set by default)
Follow Boot Order
●
●
Enable/disable the fingerprint device (enabled by default).
Enable/disable a modem device (enabled by default).
Port Options (all are enabled by
default)
NOTE: All port options are enabled by default.
●
●
●
●
Enable/disable the serial port.
Enable/disable the parallel port.
Enable/disable the flash media reader.
Enable/disable the USB port.
CAUTION: Disabling the USB port also disables MultiBay devices and ExpressCard
devices on the advanced port replicator.
●
Enable/disable the 1394 port.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Restore Security Defaults
108
Chapter 5 Computer Setup
6 Specifications
Computer specifications
Metric
U.S.
Dimensions
Depth
24.30 cm
9.57 in
Width
33.10 cm
13.03 in
Height (front to rear)
3.13 to 3.41 cm
2.40 kg
1.23 to 1.34 in
5.29 lbs
Weight (computer equipped with an optical drive, WXGA display
assembly, 1 memory module, WLAN module, and 6-cell battery)
Weight (computer equipped with the optical drive weight saver,
WXGA display assembly, 1 memory module, WLAN module, and 4-
cell battery)
2.10 kg
4.63 lbs
Input power
Operating voltage
Operating current
Temperature
19.0 V dc @ 4.74 A – 90 W
4.74 A
Operating (not writing to optical disc)
Operating (writing to optical disc)
Nonoperating
0°C to 35°C
5°C to 35°C
-20°C to 60°C
32°F to 95°F
41°F to 95°F
-4°F to 140°F
Relative humidity
Operating
10% to 90%
5% to 95%
Nonoperating
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-15 m to 12,192 m
-50 ft to 10,000 ft
-50 ft to 40,000 ft
Nonoperating
Shock
Operating
125 g, 2 ms, half-sine
200 g, 2 ms, half-sine
Nonoperating
Computer specifications
109
Metric
U.S.
Random vibration
Operating
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min
sweep rate
Nonoperating
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min
sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
14.1-inch, WXGA display specifications
Metric
U.S.
Dimensions
Height
27.94 cm
11.0 in
8.2 in
Width
20.83 cm
Diagonal
35.56 cm
14.1 in
Number of colors
Contrast ratio
Brightness
Up to 16.8 million
250:1 (typical)
180 nits (typical)
Pixel resolution
Pitch
0.279 × 0.279 mm
1280 × 800
RGB vertical stripe
Edge lit
Format
Configuration
Backlight
Character display
Total power consumption
Viewing angle
80 × 25
4.0 W
+/-40 horizontal, +20/–40° vertical (typical)
110
Chapter 6 Specifications
Hard drive specifications
250-GB*
160-GB*
120-GB*
Dimensions
9.5 mm
Height
9.5 mm
9.5 mm
9.5 mm
70 mm
Width
70 mm
70 mm
70 mm
101 g
Weight
101 g
101 g
101 g
SATA
Interface type
Transfer rate
Security
SATA
SATA
SATA
100 MB/sec
ATA security
100 MB/sec
ATA security
100 MB/sec
ATA security
100 MB/sec
ATA security
Seek times (typical read, including setting)
3 ms
Single track
3 ms
3 ms
3 ms
13 ms
Average
13 ms
13 ms
13 ms
24 ms
Maximum
24 ms
24 ms
24 ms
625,141,400
7200 rpm
Logical blocks
Disc rotational speed
Operating temperature
488,376,280
7200 rpm
312,560,640
7200 rpm
234,420,480
7200 rpm
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
Hard drive specifications
111
DVD±RW and CD-RW Double-Layer Combo Drive
specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT,
CD-ROM, CD-ROM XA, MIXED MODE
CD, CD-I, CD-I Bridge (Photo-CD, Video
CD), Multisession CD (Photo-CD, CD-
EXTRA, Portfolio, CD-R, CD-RW), CD-R,
CD-RW, DVD-ROM (DVD-5, DVD-9,
DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-RAM
Access time
Random
CD
DVD
< 175 ms
2 MB
< 230 ms
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD-ROM
24X CD-R
3,600 KB/sec
10,800 KB/sec
3,600 KB/sec
2,400 KB/sec
10,800 KB/sec
5,400 KB/sec
10,800 KB/sec
5,400 KB/sec
2,700 KB/sec
6,750 KB/sec
16X CD-RW
8X DVD+R
4X DVD+RW
8X DVD-R
4X DVD-RW
2.4X DVD+R(9)
5X DVD-RAM
112
Chapter 6 Specifications
DVD/CD-RW Combo Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT,
CD-ROM, CD-ROM XA, MIXED MODE
CD, CD-I, CD-I Bridge (Photo-CD, Video
CD), Multisession CD (Photo-CD, CD-
EXTRA, Portfolio, CD-R, CD-RW), CD-R,
CD-RW, DVD-ROM (DVD-5, DVD-9,
DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
Random
CD
DVD
< 110 ms
2 MB
< 130 ms
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD
3,600 KB/sec
3,600 KB/sec
3,600 KB/sec
3,600 KB/sec
24X CD-R
24X CD-RW
DVD/CD-RW Combo Drive specifications
113
DVD-ROM Drive
Applicable disc
DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1 and 2), CD Digital Audio,
CD-XA ready (Mode 2, Form 1 and Form 2), CD-I (Mode 2, Form 1 and Form 2), CD-R,
CD-RW, Photo CD (single and multisession), CD-Bridge
Access time
Random
CD
DVD
< 100 ms
512 KB
< 125 ms
Cache buffer
Data transfer rate
CD-R (24X)
3600 KB/s (150 KB/s at 1X CD rate)
1500 KB/s (150 KB/s at 1X CD rate)
3600 KB/s (150 KB/s at 1X CD rate)
10,800 KB/s (1,352 KB/s at 1X DVD rate)
16.6 MB/s
CD-RW (10X)
CD-ROM (24X)
DVD (8X)
Multiword DMA mode 2
114
Chapter 6 Specifications
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
DMA2*
DMA3
Not applicable
Not applicable
Not applicable
DMA4
Direct memory access controller
Available for ExpressCard
Not assigned
DMA5*
DMA6
DMA7
Not assigned
*ExpressCard controller can use DMA 1, 2, or 5.
System DMA specifications
115
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
COM1
IRQ4
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
IRQ8
Parallel port
System CMOS/real-time clock
Microsoft ACPI-compliant system
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
Synaptics PS/2 TouchPad
IRQ9*
IRQ10*
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Numeric data processor
Primary IDE channel
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial
port may assert IRQ3 or IRQ4.
116
Chapter 6 Specifications
System I/O address specifications
I/O address (hex)
000 - 00F
010 - 01F
020 - 021
022 - 024
025 - 03F
02E - 02F
040 - 05F
044 - 05F
060
System function (shipping configuration)
DMA controller no. 1
Unused
Interrupt controller no. 1
Opti chipset configuration registers
Unused
87334 “Super I/O” configuration for CPU
Counter/timer registers
Unused
Keyboard controller
061
Port B
062 - 063
064
Unused
Keyboard controller
065 - 06F
070 - 071
072 - 07F
080 - 08F
090 - 091
092
Unused
NMI enable/RTC
Unused
DMA page registers
Unused
Port A
093 - 09F
0A0 - 0A1
I/O Address (hex)
0A2 - 0BF
0C0 - 0DF
0E0 - 0EF
0F0 - 0F1
0F2 - 0FF
100 - 16F
170 - 177
178 - 1EF
1F0 - 1F7
1F8 - 200
Unused
Interrupt controller no. 2
System Function (shipping configuration)
Unused
DMA controller no. 2
Unused
Coprocessor busy clear/reset
Unused
Unused
Secondary fixed disk controller
Unused
Primary fixed disk controller
Unused
System I/O address specifications
117
I/O address (hex)
201
System function (shipping configuration)
JoyStick (decoded in ESS1688)
202 - 21F
220 - 22F
230 - 26D
26E - 26
Unused
Entertainment audio
Unused
Unused
278 - 27F
280 - 2AB
2A0 - 2A7
2A8 - 2E7
2E8 - 2EF
2F0 - 2F7
2F8 - 2FF
300 - 31F
320 - 36F
370 - 377
378 - 37F
380 - 387
388 - 38B
38C - 3AF
3B0 - 3BB
3BC - 3BF
3C0 - 3DF
3E0 - 3E1
3E2 - 3E3
3E8 - 3EF
3F0 - 3F7
3F8 - 3FF
CF8 - CFB
CFC - CFF
Unused
Unused
Unused
Unused
Reserved serial port
Unused
Infrared port
Unused
Unused
Secondary diskette drive controller
Parallel port (LPT1/default)
Unused
FM synthesizer—OPL3
Unused
VGA
Reserved (parallel port/no EPP support)
VGA
ExpressCard controller in CPU
Unused
Internal modem
“A” diskette controller
Serial port (COM1/default)
PCI configuration index register (PCIDIVO-1)
PCI configuration data register (PCIDIVO-1)
118
Chapter 6 Specifications
System memory map specifications
Size
Memory address
00000000-0009FFFF
000A0000-000BFFFF
000C0000-000CBFFF
000C8000-000E7FFF
000E8000-000FFFFF
00100000-00FFFFFF
04800000-07FFFFFF
04800000-07FFFFFF
08000000-080FFFFF
08200000-FFFEFFFF
FFFF0000-FFFFFFFF
System function
Base memory
640 KB
128 KB
48 KB
160 KB
64 KB
15 MB
58 MB
58 MB
2 MB
Video memory
Video BIOS
Unused
System BIOS
Extended memory
Super extended memory
Unused
Video memory (direct access)
Unused
4 GB
64 KB
System BIOS
System memory map specifications
119
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
5
5.0 mm
2.0 mm
5.0 mm
Where used:
(1) One captive screw that secures the Bluetooth module compartment cover to the computer (screw is
secured with a C-clip)
(2) Two captive screws that secure the hard drive bay cover to the computer (screws are secured with
C-clips)
(3) One captive screw that secures the memory module compartment cover to the computer (screw is
secured with a C-clip)
(4) One captive screw that secures the WLAN module compartment cover to the computer (screw is
secured with a C-clip)
Phillips PM2.0×5.0 captive screw
121
Phillips PM2.5×11.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
2
11.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the hard drive to the computer (screw is secured by a
C-clip)
Where used: One captive screw that secures the hard drive to the upgrade bay cradle (screw is
secured by a C-clip)
122
Chapter 7 Screw listing
Phillips 2.5×9.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
4
9.0 mm
2.5 mm
5.0 mm
Where used:
(1) One captive screw that secures the optical drive or upgrade bay device to the computer (screw is
secured by a C-clip)
(2) Three captive screws that secure the keyboard to the computer (screws are secured by C-clips)
124
Chapter 7 Screw listing
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
5
4.0 mm
2.5 mm
5.0 mm
Where used: 4 screws that secure the upgrade bay device to the computer
Where used: One screw that secures the heat sink to the system board on computer models equipped
with discrete graphics subsystem memory
126
Chapter 7 Screw listing
(2) Two screws that secure the WLAN module to the system board
Where used: One screw that secures the power button board to the switch cover
Where used: 2 screws that secure the display inverter to the display enclosure
Where used: 4 screws that secure the TouchPad bracket to the top cover
128
Chapter 7 Screw listing
Where used: 2 screws that secure the audio/ExpressCard assembly to the top cover
Where used:
(1) Three screws that secure the system board to the base enclosure on all computer models
(2) One screw that secures the system board to the base enclosure on computer models equipped with
UMA graphics subsystem memory
Phillips PM2.0×3.0 broad-head screw
Phillips PM2.0×3.0 broad-head screw
129
Color
Quantity
Length
Thread
Head diameter
Black
2
3.0 mm
2.0 mm
6.0 mm
Where used: 2 screws that secure the switch cover to the computer
130
Chapter 7 Screw listing
Where used: 2 screws that secure the display assembly to the computer
Where used: 7 screws that secure the top cover to the base enclosure
Where used: One screw that secures the speaker to the base enclosure
132
Chapter 7 Screw listing
Where used: 2 screws that secure the hinges to the display enclosure
134
Chapter 7 Screw listing
8 Backup and recovery in Windows
Vista
This chapter describes features that are common to most models. Some features may not be available
on your computer.
Overview
To protect your information, the computer provides tools to back up individual files and folders or your
entire hard drive. In case of system instability or failure, you can use the backup files to restore the
contents of your computer.
When creating backups, HP recommends the following sequence:
1. Create a set of recovery discs of the entire hard drive as soon as possible after you set up your
computer.
2. Schedule periodic backups to record changes made to your computer.
In addition to manual backup-and-recovery tools, you can use Windows® System Recovery to
automatically back up and restore your information. This feature automatically backs up changes made
to your computer daily and also at important milestones, such as when you add a program or driver.
Use this tool to restore the computer to a previous state without losing personal files or e-mails. You can
also manually set restore points and change restore settings.
Overview
137
Creating recovery discs
After setting up the computer, create a set of recovery discs for the initial backup of the entire hard
drive.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
The recovery discs are used to start up (boot) the computer and recover the operating system and
software to factory settings in case of system failure.
Note the following tips for creating recovery discs:
●
●
Connect the computer to AC power during the process.
Use any of the following types of discs (purchased separately): CD-R, CD-RW, DVD+R, DVD+R DL,
DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the type of optical drive
installed in your computer.
NOTE: DVDs and DVDs with double-layer (DL) support store more information than CDs and will
reduce the number of recovery discs required.
●
Number each disc before inserting it into the optical drive of the computer.
To create a set of recovery discs:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Back up computer.
3. Follow the on-screen instructions.
NOTE: Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running
utilities, or changing Windows settings. Refer to Help and Support for more information.
138
Chapter 8 Backup and recovery in Windows Vista
Backing up your information
After you create the recovery discs for the initial backup of the entire hard drive, you should schedule
automatic backups of your files. You should also back up your files before you modify the hardware or
software.
Several types of backup are available in the Backup and Restore Center:
●
●
●
Individual files or folders
Restore points
Entire hard drive
Backup tips
●
●
●
●
Connect the computer to AC power during the backup process.
Store personal files in the Documents folder and back them up regularly.
Back up templates that are stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot
of your settings. The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
1. Display the screen you want to save.
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4. Save the document.
Backing up your information
139
Backing up individual files or folders
When you perform a backup of the entire hard drive, you are saving the full factory image, including
the Windows operating system, software programs, all personal files and folders, and configuration
settings.
You can back up a copy of the entire hard drive to either of the following locations:
●
●
Optional external hard drive
Optical discs (CDs or DVDs)
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your hard drive:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Back up computer. You will be prompted to select a destination for the backup files.
3. Follow the on-screen instructions.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing
software, running utilities, or changing Windows settings. Refer to Help and Support for more
information.
Scheduling an automatic backup
You can schedule automatic backups for the entire system, for recovery points, or for specific files and
folders. Backups can be scheduled at specific intervals (daily, weekly, or monthly).
To schedule an automatic backup:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Change settings.
The Backup Status and Configuration Window opens.
3. Click Change backup settings. You will be prompted to select a destination for the backup
files.
4. Follow the on-screen instructions.
NOTE: Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running
utilities, or changing Windows settings. Refer to Help and Support for more information.
140
Chapter 8 Backup and recovery in Windows Vista
Creating system restore points
In addition to the manual backup-and-recovery tools, you can use Windows System Recovery to
automatically back up and restore your information. This feature automatically creates restore points
just before a significant change is made to your system, such as the installation of a program or driver.
You can also set manual restore points.
NOTE: The first system restore point is a snapshot of the entire image that is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that
time.
HP recommends that you create manual restore points at the following times:
●
●
Before you add or extensively modify software or hardware
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier restore point does not delete data files or e-mails created since that
restore point. To create a system restore point:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. On the left side of the screen, click Create a restore point or change settings.
3. Click Create. You will be prompted to name this restore point.
4. Follow the on-screen instructions.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing
software, running utilities, or changing Windows settings. Refer to Help and Support for more
information.
Backing up your information
141
Performing a recovery
In case of hard drive failure or system instability, the computer provides tools to recover your files.
You can recover your information using the following methods:
NOTE: Have your backup files available. Some of these methods will prompt you for your backup
files stored on recovery discs or on a drive.
●
●
●
Recovering individual files that you have previously backed up using Backup and Restore Center
Restoring the computer to a previous state by using system restore points
Recovering individual files that you have previously backed up or the entire hard drive using f8
recovery tools:
NOTE: You can use these methods only if the Windows recovery partition has not been deleted.
◦
◦
Windows Recovery Environment (WinRE)
Recovery Manager
●
●
Recovering the entire hard drive using f11
NOTE: You can use this method only if the Windows recovery partition has not been deleted.
Recovering information using an operating system DVD (purchased separately)
Recovering individual files
To recover individual files using the Backup and Restore Center, follow these steps:
1. If possible, back up all personal files.
2. Select Start > All Programs > Maintenance > Backup and Restore Center.
3. Click Restore files. You will be prompted to select the location of the backup files.
4. Follow the on-screen instructions.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing
software, running utilities, or changing Windows settings. Refer to Help and Support for more
information.
142
Chapter 8 Backup and recovery in Windows Vista
Restoring the computer to a previous state
Your computer automatically creates restore points daily (depending on your computer activity) and
when you make a major change to the computer, such as adding software or a new driver. If you
decide to reverse changes made to the computer, you can revert back to a previous restore point.
NOTE: If you don't like the state of your computer after you restore it, you can also undo the
restoration.
To access a restore point:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Click Restore my computer to an earlier time. A calendar is displayed to help you find
dates associated with your restore points.
3. Select the restore point to revert to.
NOTE: If you do not use your computer every day, some days may not have restore points.
Recovering information using f8 recovery tools
You can recover individual files or the entire hard drive using the recovery discs that you previously
created or an optional external hard drive where you have backed up your information.
The following tools will help you recover your information:
●
●
Windows Recovery Environment (WinRE)
Recovery Manager
NOTE: You can use these recovery methods only if the Windows recovery partition has not
been deleted.
Performing a recovery
143
Recovering information using Windows Recovery Environment (WinRE)
Windows Recovery Environment (WinRE) can perform a recovery from either an optional external hard
drive where you have backed up your information or from recovery discs that you previously created.
CAUTION: Using Windows Recovery Environment (WinRE) will completely erase hard drive contents
and reformat the hard drive. All files you have created and any software installed on the computer will
be permanently removed. When reformatting is complete, the recovery process will restore the
operating system, as well as the drivers, software, and utilities from the backup used for recovery.
To initiate recovery using WinRE, follow these steps:
NOTE: This process will take several minutes.
1. If possible, back up all personal files.
2. Restart the computer, and then press f8 before the Windows operating system loads.
3. Select Repair your computer.
NOTE: The “Repair your computer” option is displayed only if the Windows recovery partition
has not been deleted. If the option is not displayed, refer to the “Recovering information using a
Windows Vista operating system DVD (purchased separately)” section.
4. Follow the on-screen instructions.
5. Click Next.
6. Select your user name, type your password (if applicable), and then click OK.
7. If you are using recovery discs, insert the last disc of the recovery disc backup set.
NOTE: Inserting the last disc of the backup set confirms the presence of a valid backup. If you
insert any other disc, the backup will not be recognized.
– or –
If you are using an optional external hard drive, connect it to the computer.
8. Click Windows Complete PC Restore.
9. Follow the on-screen instructions.
144
Chapter 8 Backup and recovery in Windows Vista
Recovering information using Recovery Manager
If other methods do not work, you can recover your hard drive (in its factory state) as a last resort:
CAUTION: Using Recovery Manager will completely erase hard drive contents and reformat the hard
drive. All files you have created and any software installed on the computer will be permanently
removed. Recovery Manager reinstalls the operating system and HP programs and drivers that were
installed at the factory. Software not installed at the factory must be reinstalled.
1. If possible, back up all personal files.
2. Restart the computer, and then press f8 before the Windows operating system loads.
3. Select Repair your computer.
NOTE: The “Repair your computer” option is displayed only if the Windows recovery partition
has not been deleted. If the option is not displayed, refer to the “Recovering information using a
Windows Vista operating system DVD (purchased separately)” section.
4. Follow the on-screen instructions.
5. Click Next.
6. Select your user name, type your password (if applicable), and then click OK.
7. Click HP Recovery Manager.
8. Follow the on-screen instructions.
Recovering the entire hard drive using f11
You can recover the entire hard drive (in its factory state) from the Windows recovery partition using
f11.
CAUTION: Using f11 will completely erase hard drive contents and reformat the hard drive. All files
you have created and any software installed on the computer will be permanently removed. The f11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the
factory. Software not installed at the factory must be reinstalled.
NOTE: You can use this recovery method only if the Windows recovery partition has not been
deleted. To recover the hard drive from the recovery partition, follow these steps:
1. If possible, back up all personal files.
2. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
3. Press f11 while the “Press for recovery” message is displayed on the screen.
4. Follow the on-screen instructions.
Performing a recovery
145
Recovering information using a Windows Vista operating system
DVD (purchased separately)
You can purchase a Windows Vista® operating system DVD to reboot the computer and repair the
operating system. During the restore process, you will be prompted for your entire drive backup files.
Make sure that your most recent backup of the hard drive (stored on recovery discs or on an external
drive) is easily accessible. To order a Windows Vista operating system DVD, go to
http://www.hp.com/ support, select your country or region, and follow the on-screen instructions. You
can also order the DVD by calling technical support. For contact information, refer to the Worldwide
Telephone Numbers booklet included with the computer.
CAUTION: Using a Windows Vista operating system DVD will completely erase hard drive contents
and reformat the hard drive. All files you have created and any software installed on the computer will
be permanently removed. When reformatting is complete, the recovery process will help you restore the
operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
NOTE: This process will take several minutes.
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows Vista operating system DVD into the optical
drive before the Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
8. Remove the Windows Vista operating system DVD.
9. If you are using recovery discs, insert the last disc of the recovery disc backup set.
NOTE: Inserting the last disc of the backup set confirms the presence of a valid backup. If you
insert any other disc, the backup will not be recognized.
– or –
If you are using an optional external hard drive, connect it to the computer.
10. Click Windows Complete PC Restore.
11. Follow the on-screen instructions.
146
Chapter 8 Backup and recovery in Windows Vista
9 Backup and recovery in Windows
XP
This chapter describes features that are common to most models. Some features may not be available
on your computer.
Backing up your information
NOTE: You can recover only the files that you have previously backed up. HP recommends that you
use the Windows backup utility to create a hard drive backup as soon as you set up your computer.
With the Windows backup utility, you can perform the following tasks:
●
●
Backing up your information regularly to protect your important system files
Creating system recovery points that allow you to reverse undesirable changes to your computer
by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
NOTE: The Windows backup utility backs up only data files. The operating system, drivers, and
programs are located on the operating system disc and System Recovery disc that are included with the
computer.
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
Before the computer is repaired or restored
Before you add or modify hardware or software
●
●
Backing up your information
147
Backup suggestions
●
●
●
●
●
Connect the computer to external power before performing backup and recovery procedures.
Create system recovery points.
Store personal files in the My Documents folder and back up these folders periodically.
Back up templates stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot
of your settings. The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
1. Display the screen you want to save.
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, click Edit > Paste.
The screen image is added to the document.
4. Save the document.
Backing up individual files or folders
You can back up individual files or folders to an optional external hard drive or to a network drive.
NOTE: This process will take several minutes, depending on the file size and the speed of the
computer.
To back up individual files or folders:
1. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard page opens.
2. Click Next.
3. Click Backup files and settings, and then click Next.
4. Follow the on-screen instructions.
148
Chapter 9 Backup and recovery in Windows XP
Backing up all files and folders
When you back up all files and folders, you are saving all personal files and folders, all system files,
and configuration settings at one time.
NOTE: When you back up all files and folders, this does not include the operating system or
programs.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
NOTE: A copy of the backup files can be stored on an optional external hard drive or on a network
drive.
To back up all files and folders:
1. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard page opens.
2. Click Next.
3. Click Backup files and settings, and then click Next.
4. Click All information on this computer, and then click Next.
5. Follow the on-screen instructions.
Creating recovery points
When you back up system modifications since your last backup, you are creating system recovery
points. This allows you to save a snapshot of your hard drive at a specific point in time. You can then
recover back to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that
time.
HP recommends that you create recovery points at the following times:
●
●
Before you add or extensively modify software or hardware
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since that
recovery point.
To create a system recovery point:
1. Select Start > All Programs > Accessories > System Tools > System Restore.
The System Restore window opens.
2. Click Create a new restore point, and then click Next.
3. Type a short description of the restore point. This will be used as the name of the restore point.
Backing up your information
149
4. Click Create.
5. Follow the on-screen instructions.
150
Chapter 9 Backup and recovery in Windows XP
Scheduling backups
You can schedule backups for the entire system, for recovery points, or for specific files and folders.
Backups can be scheduled at specific intervals (daily, weekly, or monthly) or at specific events, such as
at system restart or when you log on.
To schedule backups:
1. Select Start > All Programs > Accessories > System Tools > Schedule Tasks.
The Schedule Tasks window opens.
2. Double-click Add Scheduled Task, and then click Next.
3. Select Backup in the Application list, and then click Next.
4. Type a name for the backup, select when you want the backup to be performed, and then click
Next.
5. Enter your user name, password, and password again to confirm. Click Next, and then click
Finish.
Performing a recovery
The Windows backup utility helps you recover important files that you have previously backed up in
case of system failure.
NOTE: To recover the operating system and programs, use the operating system disc and System
Restore disc that are included with the computer.
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1. If possible, back up all personal files.
2. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard page opens.
3. Click Restore files and settings, and the click Next.
4. Follow the on-screen instructions.
Performing a recovery
151
11 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to
120 volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or
region where the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
●
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by the power system of each country or region.
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320
Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries and regions
157
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
OVE
1
1
1
2
1
1
1
1
1
3
1
1
5
4
1
1
4
1
2
Austria
Belgium
CEBC
CSA
Canada
Denmark
DEMKO
FIMKO
UTE
Finland
France
Germany
VDE
Italy
IMQ
Japan
METI
KEMA
NEMKO
CCC
EK
The Netherlands
Norway
The People's Republic of China
South Korea
Sweden
SEMKO
SEV
Switzerland
Taiwan
BSMI
BSI
The United Kingdom
The United States
UL
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole
grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
158
Chapter 11 Power cord set requirements
12 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general
household waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the
backlight. When you remove these components, handle them carefully.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display
assembly that might require special handling at end-of-life. Disposal of mercury may be regulated
because of environmental considerations. For disposal or recycling information, contact your local
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific
details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from
one computer model to another.
Battery
159
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of
the display bezel until the bezel disengages from the display assembly.
3. Remove the display bezel (3).
160
Chapter 12 Recycling
4. Disconnect all display panel cables (1) from the display inverter and remove the display inverter
(2).
5. Remove all screws (1) that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly (2) from the display enclosure.
7. Turn the display panel assembly upside down.
8. Remove all screws that secure the display panel frame to the display panel.
9. Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
Display
161
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
162
Chapter 12 Recycling
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
17. Remove the backlight frame from the display panel.
Display
163
18. Remove the backlight from the backlight frame.
19. Disconnect the display panel cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
164
Chapter 12 Recycling
Index
Symbols/Numerics
1394 port
base enclosure, spare part
number 28, 36
battery
power 11
presentation 11
wireless 11
location 18
removal 50
battery (travel), spare part
number 34, 35
buttons
A
AC adapter, spare part numbers
AHCI (Advanced Host Controller
Interface) 107
antenna
C
BIOS Administrator Password
Bluetooth module
Cable Kit
contents 31
capacitative board, spare part
number 39
components 10
disconnecting 64, 72
locations 10
removal 54
audio card cable, spare part
number 31
audio-in jack
location 18
audio-out jack
components
Bluetooth module cable
illustrated 31
removal 95
Bluetooth module compartment
cover
illustrated 30
removal 54
built-in device
antenna 10
bottom 19
buttons 11
display 9
front 16
keys 12
left-side 18
lights 13
rear 17
right-side 17
switches 11
top 9
location 18
audio/ExpressCard assembly
removal 97
modem 108
Network Interface Controller
(LAN) 108
B
backup
modifications made to the
system 149
button
computer feet
locations 49
scheduling 140, 151
info 11
Index
165
Computer Setup
drives
feet
locations 49
accessing 103
System Configuration menu
DVD-ROM Drive
fingerprint reader board
removal 94
precautions 43
removal 59
using 103
specifications 114
DVD/CD-RW Combo Drive
precautions 43
connectors
G
grounding equipment and
methods 46
docking 19
removal 59
specifications 113
DVD±RW and CD-RW Combo
Drive
H
hard drive
D
display assembly
precautions 43
removal 59
specifications 112
precautions 43
removal 56
removal 85
specifications 111
hard drive bay cover
illustrated 30
display bezel
E
ExpressCard slot bezel, illustrated
external media cards, product
description 5
external monitor port
location 17
removal 88
removal 57
headphone jack
location 18
heat sink
Display Cable Kit, spare part
display hinge
removal 89
removal 78
Display Hinge Kit, spare part
display inverter
F
f8 recovery tools
hinge
removal 89
removal 52
Windows Recovery Environment
(WinRE) 144
fan
I
IDE (Integrated Drive Electronics)
removal 77
166
Index
webcam 9
removal 59
J
jacks
audio-in 18
audio-out 18
headphone 18
microphone 18
modem 17
network 17
RJ-11 17
RJ-45 17
M
P
mass storage devices, spare part
numbers 32
memory module
passwords 105
removal 62, 67
pin assignments
K
RJ-11 155
keyboard
memory module compartment cover
illustrated 30
removal 65
removal 62
microphone 9
microphone jack
keyboard shield
removal 75
keys
location 18
modem jack
Universal Serial Bus (USB)
port 156
location 17
Plastics Kit
esc 12
fn 12
function 12
keypad 12
modem module
contents 30
removal 69
pointing devices, product
description 6
modem module cable
illustrated 31
removal 98
monitor port
pointing stick rubber caps, spare
port options
L
language, changing in Computer
Setup 107
location 17
lights
N
network jack
location 17
drive 13, 16
keyboard 9
ports
1394 18
monitor 17
USB 17, 18
O
operating system, product
description 7
optical drive
precautions 43
Index
167
power button board
removal 76
power cord
power requirements, product
description 6
processor
recovery methods
serviceability, product description
solid-state drive, spare part
number 29, 32, 38, 41, 56
speaker
removal 96
speakers 16
Backup and Restore Center
Windows Recovery Environment
(WinRE) 144
Windows Vista operating
removal/replacement
preliminaries 42
removal 83
procedures 48
RJ-11 jack
product description
audio 4
specifications
computer 109
chipset 1
Ethernet 5
graphics 2
location 17
RJ-45 jack
display 110
DVD/CD-RW Combo Drive
location 17
keyboard 6
RTC battery
DVD±RW and CD-RW Combo
Drive 112
panels 2
ports 5
removal 73
interrupts 116
Rubber Kit, spare part number
S
Screw Kit
processors 1
security 7
serviceability 8
video 4
switch cover
contents 120
Secondary Battery Fast Charge
removal 74
system board
wireless 5
removal 100
Security menu
R
DriveLock 106
RAID (Redundant Array of
168
Index
T
top cover
W
webcam
location 9
removal 90
TouchPad
Windows Recovery Environment
(WinRE) 144
location 14
TouchPad board
removal 92
Windows Vista operating system
DVD 146
wireless antenna
TouchPad button board
removal 92
travel battery, spare part number
components 10
disconnecting 64, 72
locations 10
Wireless Antenna Kit, spare part
number 23, 36
WLAN module
TXT (Intel Trusted Execution
Technology) 108
U
removal 70
upgrade bay device
removal 60
WWAN module
upgrade bay device cradle
upgrade bay, product
description 4
removal 63
WWAN module compartment
cover
illustrated 30
USB port
removal 63
location 17, 18
using automatic restore points
V
vents 18, 19
Index
169
|
