1M23N17481
T-FHSS Air-2.4GHz Bidirectional Communication System
S.BUS2 / S.BUS Port and 8 Channels for Conventional System Receiver
R3008SB
Thank you for purchasing a Futaba R3008SB T-FHSS Air-2.4GHz compatible receiver. The R3008SB receiver features bi-directional communication
with a T-FHSS Air-2.4GHz Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized.
It also includes both standard PWM output ports and S.BUS output ports.
Applicable systems: Futaba T-FHSS Air-2.4GHz system transmitter
Be sure that the two antennas are placed at 90 degrees to each other.
Usage precaution
• The R3008SB has two antennas. In order to maximize signal reception
and promote safe modeling Futaba has adopted a diversity antenna
system. This allows the receiver to obtain RF signals on both antennas
and fly problem-free.
• Futaba T-FHSS Air system does not work with current Futaba T-
FHSS / S-FHSS / FHSS / FASST / FASSTest system.
• The R3008SB receiver can only be used with T-FHSS Air capable
transmitters.
• Don't connect Extra Voltage before turning on a receiver.
Antenna installation for carbon fuselage
WARNING
WARNING
Changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
You must leave 30mm at the tip of the antenna fully exposed. The ex-
posed antenna should be secured so that it cannot move around or back
inside of your aircraft.
DANGER
The R3008SB receiver should be protected from vibration by foam
rubber, Velcro or similar mounting methods. Protect from moisture.
S.BUS2 precaution
DANGER
5HFHLYHU
Keep away from conductive materials to avoid short circuits.
Don't connect a connector, as shown right.
Antenna installation precaution
Don't cut or bundle the receiver antenna wire.
• It will be a short-circuit, if it connected in
Do not insert either a switch
or battery in this manner.
this way. A short circuit across the battery
terminals may cause abnormal heat, fire
and burning.
Don't bend the coaxial cable. It causes damage.
Don't connect servo for conventional system to S.BUS/S.BUS2 port.
The antennas must be mounted in such a way to assure they are
strain relieved.
→
• Digital servo for conventional system It does not operate.
→
• Analog servo It may cause abnormal heat, fire and burning.
Keep the antenna as far away from the motor, ESC and other noise
sources as you possibly can.
WARNING
Only S.BUS2 capable devices may be connected the S.BUS2 port.
Standard S.BUS servos and gyros should not be connected the S.BUS2
port.
(Antenna installation)
90˚
(Typical installation)
CH Mode B
([WUDꢂ9ROWDJH
3RUW
It connects the battery
6ꢀ%86ꢂ6HUYR
for power, etc.
6HUYRꢂIRU FRQYHQWLRQDO
6ꢀ%86ꢂ*\UR
＋
External voltage input
V\VWHP
cable of an option is
used. The voltage of
－
the battery can be
displayed with a
transmitter.
%DWWHU\ꢂWRꢂꢇꢈ%
&KDQQHOꢅꢂRXWSXW
&KDQQHOꢆꢂRXWSXW
6ꢀ%86ꢂ+8%
/('
Please refer the table below
for LED status vs receiver's
0RGHꢂVZLWFK
ꢃ,WꢂLVꢂQRWꢂXVHGꢂIRUꢂDꢂOLQNꢀꢄ
condition.
6ꢀ%86ꢂSRUW ꢀꢁꢂ6%
ك 7HOHPHWU\ꢂ6HQVRU
7HOHPHWU\ꢂ6HQVRU
7HOHPHWU\ꢂ6HQVRU
LED Indication
6ꢀ%86ꢁ
SRUW
Green
Off
Red
Status
5ꢀꢁꢁꢂ6%
Battery(7/B)
$QWHQQD
ꢀ6ꢃ%86ꢄ
ك Solid No signal reception
Off Receiving signals
6ꢀ%86ꢂ+8%
Solid
Alternate blink Unrecoverable error (EEPROM, etc.)
S.BUS2
6ꢀ%86ꢂ+8%
Compliance Information Statement
(for U.S.A.)
6ꢀ%86ꢂ+8%
This device, trade name Futaba Corporation, model number R3008SB, complies with
part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
*Default setting S.BUS,
don't connect servo for
conventional system.
S.BUS(8/SB)
6ꢀ%86ꢂꢁꢂꢃ69ꢄꢂ6HUYR
6ꢀ%86ꢂꢁꢂ*\UR
(2) This device must accept any interference received, including interference that may
cause undesired operation.
(3) This module meets the requirements for a mobile device that may be used at separation
distances of more than 20cm from human body.
To meet the RF exposure requirements of the FCC this device shall not be co-located with
another transmitting device.
The responsible party of this device compliance is:
Futaba Service Center
5ꢀꢁꢁꢂ6%ꢃ6SHFLÀFDWLRQV
T-FHSS Air-2.4GHz system/S.BUS2 and S.BUS port and 8 channels for
conventional system receiver
• Dual antenna diversity
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.36 oz. (10.1g)
• Power requirement: 4.8V to 7.4V
本產品符合低功率電波輻射性電機管理辦法 第十二條、第十四條等條文規定
• Battery F/S Voltage: It sets up with a transmitter
1. 經型式認證合格之低功率射頻電機，非經許可，公司、商
號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
• Extra Voltage port: 0 70V DC
～
2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
* Be sure that when using ESCs regulated output the capacity of the ESC must
並改善
至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率
射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
meet your usage condition.
|