Dell Vostro 3360
Owner's Manual
Regulatory Model: P32G
Regulatory Type: P32G001
Contents
Notes, Cautions, and Warnings...................................................................................................2
Before Working Inside Your Computer.....................................................................................................................5
Turning Off Your Computer.......................................................................................................................................6
After Working Inside Your Computer........................................................................................................................6
Recommended Tools................................................................................................................................................9
Removing the Subscriber Identity Module (SIM) Card.............................................................................................9
Installing the SIM Card...........................................................................................................................................10
Removing the Security Digital (SD) Card................................................................................................................10
Installing the Secure Digital Card...........................................................................................................................10
Removing the Access Panel...................................................................................................................................10
Installing the Access Panel....................................................................................................................................11
Removing the Wireless Local Area Network (WLAN) Card...................................................................................11
Installing the WLAN Card.......................................................................................................................................11
Removing the Coin-Cell Battery..............................................................................................................................11
Installing the Coin-Cell Battery...............................................................................................................................12
Removing the Memory............................................................................................................................................12
Installing the Memory.............................................................................................................................................12
Removing the Keyboard..........................................................................................................................................12
Installing the Keyboard...........................................................................................................................................14
Removing the Palmrest...........................................................................................................................................14
Installing the Palmrest............................................................................................................................................17
Removing the Battery.............................................................................................................................................18
Installing the Battery..............................................................................................................................................19
Removing the Hard Drive........................................................................................................................................19
Installing the Hard Drive.........................................................................................................................................20
Removing the Display-Hinge Cover........................................................................................................................21
Installing the Display Hinge Cover..........................................................................................................................21
Removing the Display Assembly.............................................................................................................................22
Installing the Display Assembly..............................................................................................................................22
Removing the Display Bezel...................................................................................................................................23
Installing the Display Bezel.....................................................................................................................................24
Removing the Camera Module...............................................................................................................................27
Installing the Camera Module.................................................................................................................................28
Removing the Fan...................................................................................................................................................28
Installing the Fan.....................................................................................................................................................29
Removing the System Board...................................................................................................................................29
Installing the System Board....................................................................................................................................31
Removing the Heat Sink..........................................................................................................................................31
Installing the Heat Sink...........................................................................................................................................32
Removing the Speakers..........................................................................................................................................32
Installing the Speakers...........................................................................................................................................33
Removing the Power Connector.............................................................................................................................34
Installing the Power Connector..............................................................................................................................34
Removing the Input/Output (I/O) board...................................................................................................................34
Installing the I/O Board...........................................................................................................................................35
Boot Sequence.......................................................................................................................................................37
Navigation Keys......................................................................................................................................................37
System Setup Options.............................................................................................................................................38
Updating the BIOS .................................................................................................................................................42
System and Setup Password..................................................................................................................................42
Assigning a System Password and Setup Password......................................................................................42
Deleting or Changing an Existing System and/or Setup Password..................................................................43
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics...............................................................................45
Device Status Lights...............................................................................................................................................45
Battery Status Lights..............................................................................................................................................46
1
Working on Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your
personal safety. Unless otherwise noted, each procedure included in this document assumes that the following
conditions exist:
•
•
•
You have performed the steps in Working on Your Computer.
You have read the safety information that shipped with your computer.
A component can be replaced or--if purchased separately--installed by performing the removal procedure in
reverse order.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For
regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a
card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its
pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some
cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs
before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any
connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
3. If the computer is connected to a docking device (docked) such as the optional Media Base or Battery Slice,
undock it.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable
from the network device.
4. Disconnect all network cables from the computer.
5. Disconnect your computer and all attached devices from their electrical outlets.
5
6. Close the display and turn the computer upside-down on a flat work surface.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.
7. Remove the main battery.
8. Turn the computer top-side up.
9. Open the display.
10. Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before
opening the display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal
surface to dissipate static electricity, which could harm internal components.
11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your
computer.
1. Shut down the operating system:
–
In Windows 7:
Click Start
, then click Shut Down.
–
In Windows Vista :
Click Start
, then click the arrow in the lower-right corner of the Start menu as shown below, and then
click Shut Down.
–
In Windows XP:
Click Start → Turn Off Computer → Turn Off . The computer turns off after the operating system shutdown
process is complete.
2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not
automatically turn off when you shut down your operating system, press and hold the power button for about 4
seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before
turning on your computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not
use batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such
as an ExpressCard.
2. Connect any telephone or network cables to your computer.
6
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the
computer.
3. Replace the battery.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
7
8
2
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your computer.
Recommended Tools
The procedures in this document may require the following tools:
•
•
•
Small flat-blade screwdriver
Phillips screwdriver
Small plastic scribe
Removing the Subscriber Identity Module (SIM) Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Insert a paper clip into the small hole on the SIM-card holder to release it from the computer.
3. Remove the SIM-card holder from the computer.
9
4. Remove the SIM card from the SIM-card holder.
Installing the SIM Card
1. Place the SIM card into the SIM-card holder.
2. Slide the SIM card holder together with the SIM card into its slot.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Security Digital (SD) Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Press in on the SD card to release it from the computer. Slide the SD card out of the computer.
Installing the Secure Digital Card
1. Push the SD card into the slot until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
Removing the Access Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the screw that secures the access panel to the computer.
3. Remove the access panel from the computer.
10
Installing the Access Panel
1. Place the access panel to its original position on the computer.
2. Tighten the screw to secure the access panel to the computer.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Wireless Local Area Network (WLAN) Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the access panel.
3. Disconnect the antenna cables from the WLAN card and remove the screw that secures the WLAN card to the
computer. Remove the WLAN card from the computer.
Installing the WLAN Card
1. Slide the WLAN card into its slot.
2. Connect the antenna cables according to the color code on the WLAN card.
3. Install the access panel.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Coin-Cell Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the access panel.
3. Use a plastic scribe to pry the battery from the socket and lift the coin-cell battery out of the computer.
11
Installing the Coin-Cell Battery
1. Push the coin-call battery into its slot on the system board.
2. Install the access panel.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Memory
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the access panel.
3. Use your fingertips to spread apart the securing clips on each end of the memory module connector until the
memory module pops up and remove the memory module from its connector on the system board by drawing the
module from the system board at 45-degree angle.
Installing the Memory
1. Insert and secure the memory module to the system board.
2. Install the access panel.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Keyboard
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the screw that secures the keyboard to the chassis.
12
3. Starting on the right side of the system, use a plastic scribe to pry up the keyboard from the computer.
4. Flip the keyboard over and lay it on the palmrest.
5. Lift the clip to release the keyboard cable and disconnect it from the computer.
13
Installing the Keyboard
1. Connect the keyboard cable to the system board.
2. Place the keyboard back to its original position.
3. Tighten the screw to secure the keyboard to the computer.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Palmrest
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) display hinge cover
3. Using a plastic scribe pry out the rubber pads that cover the front screws on the base cover.
4. Remove the screws that secure the palmrest to the computer.
14
5. Disconnect the quick launch board cable, the finger print reader cable, and the palmrest cable from the system
board.
6. Disconnect the power LED cable and the LED board cable from the system board.
15
7. Remove the screws that secure the palmrest to the front of the computer.
8. Pry along the edges of the palmrest to release the palmrest.
16
9. Lift the palmrest up and away from the computer.
Installing the Palmrest
1. Starting from the edges of the palmrest, press downwards on the palmrest to engage the tabs on the computer.
2. Tighten the screws to secure the palmrest to the front of the computer.
3. Connect the power LED cable and the LED board cable to the system board.
4. Connect the quick launch board cable, the finger print reader cable, and the palmrest cable to the system board.
5. Tighten the screws to secure the palmrest to the back of the computer.
6. Push the rubber pads to cover the screws on the computer.
7. Install the keyboard.
8. Install the access panel.
9. Follow the procedures in After Working Inside Your Computer.
17
Removing the Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the:
a) access panel
b) keyboard
c) palmrest
3. Disconnect the battery cable from the system board.
4. Remove the screws that secure the battery to the system board.
5. Remove the battery from the computer.
18
Installing the Battery
1. Place the battery into the battery bay.
2. Replace and tighten the screws that secure the battery to the computer.
3. Connect the battery cable to the system board.
4. Install:
a) palmrest
b) keyboard
c) access panel
5. Follow the procedures in After Working Inside Your Computer.
Removing the Hard Drive
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the:
a) access panel
b) keyboard
c) palmrest
d) battery
3. Remove the screws that secure the hard drive to the computer.
19
4. Lift the hard drive to disconnect the hard-drive cable.
5. Disconnect the hard-drive cable from the hard drive and remove the hard drive from the computer.
6. Remove the screws that secure the hard-drive bracket to the hard drive and remove the hard drive bracket from it.
Installing the Hard Drive
1. Tighten the screws to secure the hard drive bracket to the hard drive.
2. Connect the hard drive cable to the hard drive and place the hard drive back to its original position on the
computer.
3. Tighten the screws to secure the hard drive to the computer.
4. Install:
a) battery
b) palmrest
c) keyboard
d) access panel
5. Follow the procedures in After Working Inside Your Computer.
20
Removing the Display-Hinge Cover
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the access panel.
3. Remove the screws that secure the display-hinge cover to the computer.
4. Remove the display-hinge cover from the computer.
Installing the Display Hinge Cover
1. Align the display hinge cover to its original position on the computer.
2. Tighten the screws to secure the display hinge cover to the computer.
3. Install the access panel.
4. Follow the procedures in After Working Inside Your Computer.
21
Removing the Display Assembly
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the:
a) access panel
b) keyboard
c) palmrest
d) battery
e) display hinge cover
3. Release the antenna cables from their routing.
4. Disconnect the display cable from the system board and remove the screws that secure the display assembly to
the computer.
Installing the Display Assembly
1. Connect the display cable to the system board and tighten the screws to secure the display assembly to the
computer.
2. Thread the hard drive cable through its routing tabs.
3. Thread the antenna cables through their routing tabs.
4. Install :
a) display hinge cover
b) battery
c) palmrest
d) keyboard
22
e) access panel
5. Follow the procedures in After Working Inside Your Computer.
Removing the Display Bezel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
e) display assembly
3. Using a plastic scribe, pry under the display bezel to release it from the display assembly.
4. Lift the display bezel and remove it from the display assembly.
23
Installing the Display Bezel
1. Align the display bezel with the display assembly and gently snap it into place.
2. Install :
a) display hinge cover
b) battery
c) palmrest
d) keyboard
e) access panel
3. Follow the procedures in After Working Inside Your Computer.
Removing the Display Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
e) display hinge cover
f) display assembly
g) display bezel
3. Disconnect the camera cable from its connector on the camera module.
4. Remove the screws that secure the display panel to the display back cover.
24
5. Flip the display panel from the display assembly.
6. Place the display panel with its front facing down to access the display and camera cables attached to it.
25
7. Pull out the plastic tab to disconnect the display cable from the display panel.
8. Remove the camera cable from the display panel.
26
Installing the Display Panel
1. Place the camera cable on the back of the display panel.
2. Connect the display cable to its connector on the display panel.
3. Place the display panel to its original position on the display assembly.
4. Tighten the screws to secure the display panel to the display assembly.
5. Connect the camera cable to camera module.
6. Install :
a) display bezel
b) display assembly
c) display hinge cover
d) battery
e) palmrest
f) keyboard
g) access panel
7. Follow the procedures in After Working Inside Your Computer.
Removing the Camera Module
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
e) display hinge cover
f) display assembly
g) display bezel
3. Disconnect the camera cable from the camera module and remove the camera module from the display assembly.
27
Installing the Camera Module
1. Connect the camera cable to the camera module and place the camera module to its original position on the
display assembly.
2. Install :
a) display bezel
b) display assembly
c) display hinge cover
d) battery
e) palmrest
f) keyboard
g) access panel
3. Follow the procedures in After Working Inside Your Computer.
Removing the Fan
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
e) display hinge cover
f) display assembly
3. Remove the screw that secures the fan to the computer. Then, lift the fan and disconnect the fan cable from the
system board.
28
Installing the Fan
1. Connect the fan cable to the system board.
2. Tighten the screws to secure the fan to the computer.
3. Install :
a) display assembly
b) display hinge cover
c) battery
d) palmrest
e) keyboard
f) access panel
4. Follow the procedures in After Working Inside Your Computer.
Removing the System Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) display hinge cover
e) display assembly
f) fan
3. Disconnect the I/O cable from the I/O daughter board.
29
4. Remove the screws that secure the system board to the computer.
5. Remove the hard-drive cable from its routing and flip the system board to access the power connector cable.
6. Disconnect the power-connector cable from the system board.
30
Installing the System Board
1. Connect the power connector cable to the system board.
2. Thread the hard drive cable through its routing tabs.
3. Tighten the screws to secure the system board to the computer.
4. Connect the I/O board cable to the I/O board.
5. Install :
a) fan
b) display assembly
c) display hinge cover
d) battery
e) palmrest
f) keyboard
g) access panel
6. Follow the procedures in After Working Inside Your Computer.
Removing the Heat Sink
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) display hinge cover
e) display assembly
f) fan
g) system board
3. Remove the screws that secure the heat sink to the system board.
31
4. Remove the heat sink from the system board,
Installing the Heat Sink
1. Tighten the screws to secure the heat sink to the system board.
2. Install :
a) system board
b) fan
c) display assembly
d) display hinge cover
e) battery
f) palmrest
g) keyboard
h) access panel
3. Follow the procedures in After Working Inside Your Computer.
Removing the Speakers
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
e) hard drive
3. Disconnect the speaker cable from the I/O board.
32
4. Release the speaker cables from their routing and remove the speakers from the computer.
Installing the Speakers
1. Place the speakers on the computer and thread the speakers cable through the routing tabs.
2. Connect the speaker cable to the I/O board
3. Install :
a) hard drive
b) battery
c) palmrest
d) keyboard
e) access panel
4. Follow the procedures in After Working Inside Your Computer.
33
Removing the Power Connector
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
e) display hinge cover
f) display assembly
g) fan
h) system board
3. Remove the screw that secures the power connector to the computer and remove the power connector from the
computer.
Installing the Power Connector
1. Tighten the screw to secure the power connector to the computer.
2. Install :
a) system board
b) fan
c) display assembly
d) display hinge cover
e) battery
f) palmrest
g) keyboard
h) access panel
3. Follow the procedures in After Working Inside Your Computer.
Removing the Input/Output (I/O) board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) access panel
b) keyboard
c) palmrest
d) battery
3. Disconnect the speaker cable and the I/O-board cable from the I/O board.
34
4. Remove the screws that secure the I/O board to the computer and remove it from the computer.
Installing the I/O Board
1. Connect the speaker cable and the I/O-board cable to the I/O board.
2. Tighten the screws to secure the I/O board to the computer.
3. Install :
a) battery
b) palmrest
c) keyboard
d) access panel
4. Follow the procedures in After Working Inside Your Computer.
35
36
3
System Setup
System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup,
you can:
•
•
•
•
•
Change the NVRAM settings after you add or remove hardware
View the system hardware configuration
Enable or disable integrated devices
Set performance and power management thresholds
Manage your computer security
Boot Sequence
Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a specific device
(for example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
•
•
Access System Setup by pressing <F2> key
Bring up the one-time boot menu by pressing <F12> key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot-menu
options are:
•
•
Removable Drive (if available)
STXXXX Drive
NOTE: XXX denotes the SATA drive number.
•
•
Optical Drive
Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup screen.
Navigation Keys
The following table displays the system setup navigation keys.
NOTE: For most of the system setup options, changes that you make are recorded but do not take effect until you
restart the system.
Table 1. Navigation Keys
Keys
Navigation
Up arrow
Down arrow
Moves to the previous field.
Moves to the next field.
37
Keys
Navigation
<Enter>
Spacebar
<Tab>
Allows you to select a value in the selected field (if applicable) or follow the link in the field.
Expands or collapses a drop‐down list, if applicable.
Moves to the next focus area.
NOTE: For the standard graphics browser only.
<Esc>
<F1>
Moves to the previous page till you view the main screen. Pressing <Esc> in the main screen
displays a message that prompts you to save any unsaved changes and restarts the system.
Displays the System Setup help file.
System Setup Options
NOTE: The system setup options may vary depending on the computer model.
The Main tab lists out the primary hardware features of the computer. The table below defines the function of each
option.
Table 2. Main Options
Main
System Information
System Time
Displays the computer
model number.
Allows you to reset the time
on the computer's internal
clock.
System Date
Allows you to reset the date
on the computer's internal
calendar.
BIOS Version
Product Name
Displays the BIOS revision.
Displays the product name
and the model number.
Service Tag
Asset Tag
CPU Type
Displays the service tag of
your computer.
Displays the asset tag of
your computer (if available).
Displays the type of
processor.
CPU Speed
Displays the speed of the
processor.
CPU ID
Displays the processor ID.
CPU Cache
L1 Cache
Displays the processor L1
cache size.
38
Main
L2 Cache
L3 Cache
Displays the processor L2
cache size.
Displays the processor L3
cache size.
Fixed HDD
Displays the model number
and capacity of the hard
drive.
SATA ODD
mSata Device
Displays the model number
and capacity of the optical
drive.
Displays the model number
and capacity of the mini-
Sata device.
AC Adapter Type
Extended Memory
System Memory
Displays the type of the AC
adapter.
Displays the memory
installed on the computer.
Displays the memory in-built
on the computer.
Memory Speed
Keyboard Type
Displays the memory speed.
Displays the type of
keyboard.
The Advanced tab allows you to set various functions that affect the performance of the computer. The table below
defines the function of each option and its default value.
Table 3. Advanced Options
Advanced
Intel SpeedStep
Virtualization
Enable or disable the Intel
SpeedStep feature.
Default: Enabled
Default: Enabled
Enable or disable the Intel
Virtualization feature.
Integrated NIC
Enable or disable the power Default: Enabled
supply to the on–board
network card.
USB Emulation
Enable or disable the USB
emulation feature.
Default: Enabled
Default: Disabled
USB Wake Support
Allows USB devices to
wake-up the computer from
standby. This feature is
enabled only when the AC
adapter is connected.
39
Advanced
SATA Operation
Change the SATA controller Default: AHCI
mode to either ATA or AHCI.
Adapter Warnings
Function Key Behavior
Charger Behavior
Enables or disables adapter Default: Enabled
warnings.
Specifies the behavior of
the function key <Fn> .
Default: Function key first
Specifies if the computer
battery will be charged
when connected to an AC
power source.
Default: Enabled
Battery Health
Specifies the health of the
battery.
Intel Rapid Start Technology
Miscellaneous Devices
Allows you to configure the
Intel rapid start technology
These fields let you enable
or disable various on-board
devices.
External USB Ports
Microphone
Enables or disables external Default: Enabled
USB ports.
Enables or disables
microphone.
Default: Enabled
Camera
Enables or disables camera. Default: Enabled
Media Card Reader
Enables or disables media
card reader.
Default: Enabled
Optical Drive
Enables or disables optical Default: Enabled
drive.
Fingerprint Reader
Enables or disables
fingerprint reader.
Default: Enabled
Boot Disable
USB debug
Enables or disables boot.
Default: Disabled
Default: Disabled
Enables or disables USB
debug.
Internal Bluetooth
Enables or disables internal Default: Enabled
bluetooth.
Internal WLAN
Internal WWAN
Enables or disables WLAN. Default: Enabled
Enables or disables WWAN. Default: Enabled
The Security tab displays the security status and allows you to manage the security features of the computer.
40
Table 4. Security Options
Security
Set Service Tag
This field displays your system's service tag. If the service
tag is not already set, this field can be used to enter it.
Admin Password
This field displays if a admin password is set for this
computer or not (Default: Cleared/Not installed)
System Password
Hdd Password State
Set Supervisor Password
Set HDD Password
Password Change
Password Bypass
This field displays if a system password is set for this
computer or not (Default: Cleared/Not installed)
This field displays if a HDD password is set for this
computer or not (Default: Cleared)
Allows you to change or delete the administrator
password.
Allows you to set a password on the computer's internal
hard drive (HDD).
Allows you to add/remove permission for changing
passwords.
Allows you to bypass the system password and the
internal HDD password prompts during a system restart/
resume from hibernate state. (Default: Disabled)
Computrace
Enable or disable the Computrace feature on your
computer.
The Boot tab allows you to change the boot sequence.
Table 5. Boot Options
Boot
Boot Priority Order
Specifies the order of different devices in which the
computer will boot through at start up.
Removable Drive
Hard Disk Drives
USB Storage Device
Specifies the removable drive the computer can boot
through.
Specifies which hard drive the computer can boot
through.
Specifies which USB storage device the computer can
boot through.
CD/DVD/CD-RW Drive
Network
Specifies which CD/DVD the computer can boot through.
Specifies which network device the computer can boot
through.
Exit — This section allows you to save, discard, and load default settings before exiting from System Setup.
41
Updating the BIOS
It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For
notebooks, ensure that your computer battery is fully charged and connected to a power outlet
1. Restart the computer.
2. Go to support.dell.com/support/downloads.
3. If you have your computer's Service Tag or Express Service Code:
NOTE: For desktops, the service tag label is available on the front of your computer.
NOTE: For notebooks, the service tag label is available on the bottom of your computer.
a) Enter the Service Tag or Express Service Code and click Submit.
b) Click Submit and proceed to step 5.
4. If you do not have your computer's service tag or express service code, select one of the following:
a) Automatically detect my Service Tag for me
b) Choose from My Products and Services List
c) Choose from a list of all Dell products
5. On the application and drivers screen, under the Operating System drop-down list, select BIOS.
6. Identify the latest BIOS file and click Download File.
7. Select your preferred download method in the Please select your download method below window; click Download
Now.
The File Download window appears.
8. Click Save to save the file on your computer.
9. Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
System and Setup Password
You can create a system password and a setup password to secure your computer.
Password Type
Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to the BIOS settings of your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if is not locked and left unattended.
NOTE: Your computer is shipped with the system and setup password feature disabled.
Assigning a System Password and Setup Password
You can assign a new System Password and/or Setup Password or change an existing System Password and/or Setup
Password only when Password Status is Unlocked. If the Password Status is Locked, you cannot change the System
Password.
42
NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you
need not provide the system password to log on to the computer.
To enter a system setup, press <F2> immediately after a power-on or reboot.
1. In the System BIOS or System Setup screen, select System Security and press <Enter>.
The System Security screen appears.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password , enter your system password, and press <Enter> or <Tab>.
Use the following guidelines to assign the system password:
–
–
–
–
A password can have up to 32 characters.
The password can contain the numbers 0 through 9.
Only lower case letters are valid, upper case letters are not allowed.
Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
Re-enter the system password when prompted.
4. Type the system password that you entered earlier and click OK.
5. Select Setup Password, type your system password and press <Enter> or <Tab>.
A message prompts you to re-type the setup password.
6. Type the setup password that you entered earlier and click OK.
7. Press <Esc> and a message prompts you to save the changes.
8. Press <Y> to save the changes.
The computer reboots.
Deleting or Changing an Existing System and/or Setup Password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing
System and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password
Status is Locked.
To enter the System Setup, press <F2> immediately after a power-on or reboot.
1. In the System BIOS or System Setup screen, select System Security and press <Enter>.
The System Security screen is displayed.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.
4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.
NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete
the System and/or Setup password, confirm the deletion when promoted.
5. Press <Esc> and a message prompts you to save the changes.
6. Press <Y> to save the changes and exit from the System Setup.
The computer reboots.
43
44
4
Diagnostics
If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical
assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional
equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use the
diagnostics results to help you solve the problem.
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is
embedded with the BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of
options for particular devices or device groups allowing you to:
•
•
•
•
•
•
Run tests automatically or in an interactive mode
Repeat tests
Display or save test results
Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
View status messages that inform you if tests are completed successfully
View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may
cause invalid results or error messages.
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the
computer terminal when the diagnostic tests are performed.
1. Power-on the computer.
2. As the computer boots, press the <F12> key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the computer. The
diagnostics starts running the tests on all the detected devices.
4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the diagnostic test.
5. Select the device from the left pane and click Run Tests.
6. If there are any issues, error codes are displayed.
Note the error code and contact Dell.
Device Status Lights
Table 6. Device Status Lights
Turns on when you turn on the computer and blinks when the computer is in a power management mode.
Turns on when the computer reads or writes data.
45
Turns on steadily or blinks to indicate battery charge status.
Turns on when wireless networking is enabled.
Battery Status Lights
If the computer is connected to an electrical outlet, the battery light operates as follows:
Alternately blinking amber light and white An unauthenticated or unsupported non-Dell AC adapter is attached to
light
your laptop.
Alternately blinking amber light with steady Temporary battery failure with AC adapter present.
white light
Constantly blinking amber light
Light off
Fatal battery failure with AC adapter present.
Battery in full charge mode with AC adapter present.
Battery in charge mode with AC adapter present.
White light on
Diagnostic Beep Codes
The following table shows the possible beep codes that may be emitted by the computer when your computer is unable
to complete a power on self test.
Table 7. Diagnostic Beep Codes
Beep
1
Description
Possible Cause/Troubleshooting
Steps
BIOS ROM checksum in progress of
failure.
System board failure, covers BIOS
corruption or ROM error
2
3
4
No RAM detected
If no memory is detected, you can
perform the following steps
•
•
•
reseat the memory if an
additional memory is available
install that memory if the
issue persists
issue with the memory
connector
System board failure
•
Chipset Error (North and
South Bridge Chipset,
DMA/IMR/Timer Error)
•
•
•
•
Time-Of-Day Clock test failure
Gate A20 failure
Super I/O chip failure
Keyboard controller test
failure
RAM Read/Write failure
If no memory is detected, you can
perform the following steps
46
Beep
Description
Possible Cause/Troubleshooting
Steps
•
•
•
reseat the memory if an
additional memory is available
install that memory if the
issue persists
issue with the memory
connector
5
Real-time clock power fail
CMOS battery failure. Reseat the
battery. If issue persists, there can be
an issue with the coin-cell battery or
the connector (that will involve
replacing the system board)
6
7
8
Video BIOS Test Failure
Processor Failure
Display
Video card failure
Processor failure
Display failure
47
48
5
Specifications
NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start
(Start icon) → Help and Support, and then select the option to view information about your computer.
Table 8. System Information
Feature
Description
Chipset
Intel HM77 Express Chipset
64-bit
DRAM bus width
Flash EPROM:
Vostro 3360 / Vostro 3460
Vostro 3560
SPI 8 MB
SPI 6 MB
Table 9. Processor
Feature
Types
Description
•
•
•
Intel Core i3 series
Intel Core i5 series
Intel Core i7 series
L3 cache
up to 6 MB
Table 10. Memory
Feature
Description
Memory connector
Memory capacity
Memory type
two SODIMM slots
2 GB, 4 GB, 6 GB, or 8 GB
DDR3 SDRAM (1333 MHz and 1600 MHz)
Minimum memory
Maximum memory
2 GB
8 GB
Table 11. Audio
Feature
Description
Type
2 channel high definition audio
Controller:
Vostro 3360
Cirrus Logic CS4213D
49
Feature
Vostro 3460 / Vostro 3560
Description
Conexant CX20672-21Z
Stereo conversion
Interface:
24-bit (analog-to-digital and digital-to-analog)
Internal
high definition audio
External
microphone-in/stereo headphones/external speakers connector
Speakers
2 W
Volume controls
keyboard function keys and program menus
Table 12. Video
Feature
Description
Video type
•
•
integrated on system board
discrete
Data bus:
UMA
integrated video
Discrete:
Vostro 3460
•
•
PCI-E x16 Gen1
PCI-E x16 Gen2
Vostro 3560
Video controller:
UMA
PCI-E x8 Gen 2
•
•
Intel HD Graphics 3000
Intel HD Graphics 4000
Discrete:
Vostro 3460
Vostro 3560
nVidia GeForce GT 630M
AMD Radeon HD7670M
Table 13. Camera
Feature
Description
Camera Resolution
Video Resolution (maximum)
HD 720P
1280 x 720 pixels at 30 FPS
Table 14. Communication
Feature
Description
Network adapter
Wireless
10/100/1000 Mbps Ethernet LAN
•
internal WLAN
50
Feature
Description
•
•
Bluetooth
WWAN (optional)
Table 15. Ports and Connectors
Feature
Description
Audio:
Vostro 3360
Vostro 3460 / 3560
Video
one stereo headphone/headset/audio-out connector
one microphone connector, one headphone connector
•
•
one 15-pin VGA connector
one 19-pin HDMI connector
Network adapter
USB 3.0:
one RJ-45 connector
Vostro 3360
three
four
Vostro 3460 / Vostro 3560
NOTE: The powered USB 3.0 connector also supports Microsoft Kernel Debugging. The ports are identified in the
documentation shipped with your computer.
Media card reader
Table 16. Display
one 8-in-1
Feature
Description
Type
HD WLED AG
Size:
Vostro 3360
Vostro 3460
Vostro 3530
Dimensions:
Height
13.0 inches
14.0 inches
15.0 inches
Vostro 3360
Vostro 3460
Vostro 3560
240 mm (9.44 inches) 245 mm (9.64 inches) 259 mm (10.19 inches)
330 mm (12.99 inches) 340 mm (13.38 inches) 375 mm (14.76 inches)
Width
Diagonal
330 mm (13 inches)
330 mm x 240 mm
355.60 mm (14 inches) 381 mm (15 inches)
340 mm x 245 mm 375 mm x 259 mm
Active area (X/Y)
Maximum resolution:
Vostro 3360/3460
Vostro 3560
1366 x 768 pixels at 262K colors
1920 x 1080 FHD
51
Feature
Description
200 nits
Maximum Brightness
Operating angle
Refresh rate
0° (closed) to 140°
60 Hz
Minimum Viewing angles:
Horizontal
40°/40°
Vertical
15°/30° (H/L)
0.23 mm x 0.23 mm
Pixel pitch
Table 17. Keyboard
Feature
Description
Number of keys:
Vostro 3360
United States and Canada: 80 keys, Europe and Brazil: 81 keys, Japan:
84 keys
Vostro 3460/3560
United States and Canada: 86 keys, Europe and Brazil: 87 keys, Japan:
90 keys
Table 18. Touchpad
Feature
Active Area:
X-axis
Description
Vostro 3360
Vostro 3460/3560
82.00 mm (3.22 inches)
45.00 mm (1.77 inches)
90.00 mm (3.54 inches)
49.00 mm (1.93 inches)
Y-axis
Table 19. Battery
Feature
Description
Type:
Vostro 3360
Vostro 3460/3560
Dimensions:
Height
4-cell lithium ion (3.4 Ahr/cell or 49 Whr)
6-cell lithium ion (2.2 Ahr/cell or 48 Whr)
Vostro 3360
Vostro 3460
Vostro 3560
20.20 mm (0.80 inch)
208.36 mm (8.20 inches)
20 mm (0.79 inch)
20 mm (0.79 inch)
Width
208 mm (8.19
inches)
208 mm (8.19
inches)
Depth
Weight
56.52 mm (2.22 inches)
0.33 kg (0.73 lb)
51 mm (2.00 inches) 51 mm (2.00 inches)
0.33 kg (0.73 lb) 0.33 kg (0.73 lb)
Charge time
Voltage:
approximately 4 hours (when the computer is turned off)
52
Feature
Vostro 3360
Description
14.8 VDC
Vostro 3460 / Vostro 3560
Temperature range:
Operating
11.1 VDC
0 °C to 35 °C (32 °F to 95 °F)
–40 °C to 65 °C (–40 °F to 149 °F)
3 V CR2032 lithium coin cell
Non-Operating
Coin-cell battery
Table 20. AC Adapter
Feature
Type:
Description
65 W
Vostro 3360 / Vostro 3460 / Vostro 3560
with integrated video card
Vostro 3460 with discrete video card
Vostro 3560 with quad core
Input voltage
90 W
90 W
100 VAC to 240 VAC
1.50 A/1.60 A/1.70 A
50 Hz to 60 Hz
65 W and 90 W
Input current (maximum)
Input frequency
Output power
Output current:
65 W
3.34 A (continuous)
4.62 A
90 W
Rated output voltage
Dimensions:
19.50 VDC (+/– 1.0 VDC)
Height
28.20 mm (1.11 inches)
57.90 mm (2.28 inches)
137.16 mm (5.40 inches)
Width
Depth
Temperature range:
Operating
0 °C to 35 °C (32 °F to 95 °F)
Non-Operating
–40 °C to 70 °C (–40 °F to 158 °F)
53
Table 21. Physical
Feature
Description
Vostro 3360
Vostro 3460
Vostro 3560
Height
Width
Depth
19.20 mm (0.75 inch)
30.10 mm (1.18
inches)
32.50 mm (1.27 inches)
332.00 mm (13.07
inches)
345.50 mm (13.60
inches)
375.00 mm (14.76
inches)
232.50 mm (9.15
inches)
244.00 mm (9.60
inches)
259.00 mm (10.19
inches)
Weight (with battery pack)
1.66 kg (3.65 lb)
2.23 kg (4.91 lb)
2.57 kg (5.66 lb)
Table 22. Environmental
Feature
Description
Temperature:
Operating
0 °C to 35 °C (32 °F to 95 °F)
Storage
–40 °C to 65 °C (–40 °F to 149 °F)
Relative humidity (maximum):
Operating
10 % to 90 % (noncondensing)
5 % to 95 % (noncondensing)
Storage
Altitude (maximum):
Operating
–15.2 m to 3048 m (–50 ft to 10,000 ft)
–15.2 m to 10,668 m (–50 ft to 35,000 ft)
G1 as defined by ISA-71.04–1985
Non-Operating
Airborne contaminant level
54
6
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice,
packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and
product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer
service issues:
1. Visit support.dell.com.
2. Select your support category.
3. If you are not a U.S. customer, select your country code at the bottom of the support.dell.com page, or select All to
see more choices.
4. Select the appropriate service or support link based on your need.
55
|