GT4245
GT4550
G
H
I
3
(Original instructions)
ENGLISH
3. Personal safety
Intended use
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Your Black & Decker hedgetrimmer has been designed for
trimming hedges, shrubs and brambles. This tool is intended
for consumer use only.
Safety instructions
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
@
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains
operated (corded) power tool or battery operated (cordless)
power tool.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
4
(Original instructions)
ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
u
u
u
Never touch the blades while the tool is running.
Never attempt to force the blades to come to a standstill.
Do not put the tool down until the blades have come to a
complete standstill.
Regularly check the blades for damage and wear. Do not
use the tool when the blades are damaged.
Take care to avoid hard objects (e.g. metal wire, railings)
when trimming. Should you accidentally hit any such
object, immediately switch the tool off and check for any
damage.
Should the tool start to vibrate abnormally, immediately
switch it off and disconnect it from the mains suply then
check for any damage.
If the tool stalls, immediately switch it off. Disconnect it
from the mains supply before attempting to remove any
obstructions.
After use, place the blade sheath supplied over the
blades. Store the tool, making sure that the blade is not
exposed.
Always ensure that all guards are fitted when using the
tool. Never attempt to use an incomplete tool or a tool with
unauthorised modifications.
Never allow children to use the tool.
Be aware of falling debris when cutting the higher sides of
a hedge.
u
u
u
u
u
u
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for hedge
u
u
trimmers
@
u Keep all parts of the body away from the cutter blade.
Do not remove cut material or hold material to be cut
when blades are moving. Make sure the switch is off
when clearing jammed material. A moment of inattention
while operating the tool can result in serious personal
injury.
u
Always hold the tool with both hands and by the handles
provided.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Carry the hedge trimmer by the handle with the cutter
blade stopped. When transporting or storing the
hedge trimmer always fit the cutting device cover.
Proper handling of the hedge trimmer will reduce possible
personal injury from the cutter blades.
u Hold the power tool by insulated gripping surfaces
only, because the cutter blade may contact hidden
wiring or its own cord. Cutter blades contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
u Keep cable away from cutting area. During operation
the cable can be hidden in shrubs and can be accidentally
cut the blades.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual can present a risk of
personal injury and/or damage to property.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u
If you have not used a hedge trimmer before, preferably
seek practical instruction by an experienced user in addi-
tion to studying this manual.
u Impairment of hearing.
5
(Original instructions)
ENGLISH
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
#
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
u When using the tool outdoors, only use extension cables
intended for outdoor use. A suitable rated Black & Decker
extension cable of up to 30 m can be used without loss of
power.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
u Electric safety can be further improved by using a high-
sensitivity 30 mA residual current device (RCD).
Features
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
This tool includes some or all of the following features.
1. Trigger switch
2. Front handle switch
3. Front handle
4. Guard
5. Blade
6. Cable restraint
Labels on tool
The following pictograms are shown on the tool:
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged and that the blade sheath is fitted
over the blades.
Warning! To reduce the risk of injury, the user
:
must read the instruction manual.
Fitting the guard (fig. A & B)
u Remove the two partially inserted screws from the body of
the tool.
Wear safety glasses or goggles when operating
u Locate the guard (4) into the grooves.
u Secure the guard using the two screws (7) supplied.
Warning! Never use the tool without the guard.
O
this tool.
Connecting the tool to the mains (fig. C)
Unless the tool is fitted with a mains cable, you will need to
connect an extension cable to the power inlet.
u Connect the female socket of a suitable extension cable to
the power inlet of the tool.
u Loop the cable through the cable restraint (6) as shown
to prevent the extension cable from becoming detached
during use.
Wear ear protection when operating this tool.
N
Immediately disconnect the cable from the
mains if it is damaged or cut.
E
u Insert the mains plug into a mains outlet.
Warning! The extension cable must be suitable for outdoor
use. When using a cable reel, always unwind the cable
completely.
Do not expose the tool to rain or high humidity.
R
Directive 2000/14/EC guaranteed sound power.
96
6
(Original instructions)
ENGLISH
u Trim conifers and other fast growing shrubs every six
weeks from May until October.
Use
Warning! Let the tool work at its own pace. Do not overload.
Guidelines for trimming (Australia & New Zealand)
u Trim hedges and shrubs with seasonal leaves (new leaves
every year) in December and March.
Rotating the front handle (fig. D) (GT4550 Only)
For you comfort and convienience during use, the front handle
can be rotated into 5 diferent positions.
u Trim evergreens in September and February.
u Trim conifers and other fast growing shrubs every six
weeks from October until March.
u Press in the front handle rotate button (8).
u Rotate the front handle (3) to the required position.
u Release the front handle rotate button (8).
Note: It is not possible to rotate the front handle of the hedge
trimmer whilst the hedge trimmer is running.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the perform-
ance of your tool. By using these accessories you will get the
very best from your tool.
Switching on and off
Note: For your safety, this tool is equipped with a double
switching system. This system prevents starting the tool
inadvertently and will only allow operation while holding the
tool with both hands.
Lubrication oil is available from your Black & Decker dealer
(cat. no. A6102-XJ).
Switching on (Fig. E)
u Take hold of the front handle (3) with one hand so that the
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
front handle switch (2) is pushed into the body of the front
handle.
u With the other hand, squeeze the trigger switch (1) to start
the tool.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switching off
u Release the handle switch (2) or the trigger switch (1).
Warning! Never attempt to lock a switch in the on position.
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u After use, carefully clean the blades. After cleaning, apply
a film of light machine oil to prevent the blades from rust-
ing.
Hints for optimum use
u Start by trimming the top of the hedge. Slightly tilt the tool
(up to 15° relative to the line of cut) so that the blade tips
point slightly towards the hedge (fig. F). This will cause the
blades to cut more effectively. Hold the tool at the desired
angle and move it steadily along the line of cut. The
double-sided blade allows you to cut in either direction.
u In order to obtain a very straight cut, stretch a piece of
string along the length of the hedge at the desired height.
Use the string as a guideline, cutting just above it (fig. G).
u In order to obtain flat sides, cut upwards with the growth.
Younger stems move outwards when the blade cuts
downwards, causing shallow patches in the hedge (fig. H).
u Take care to avoid any foreign objects. Especially avoid
hard objects such as metal wire and railings, as these
could damage the blades (fig. I).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Regularly oil the blades.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Guidelines for trimming
u Trim hedges and shrubs with seasonal leaves (new leaves
every year) in June and October.
u Trim evergreens in April and August.
7
(Original instructions)
ENGLISH
Protecting the environment
Technical data
Separate collection. This product must not be
disposed of with normal household waste.
GT4245 (Type 1)
GT4550 (Type 1)
Z
Voltage
VAC
W
230
420
230
450
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
Power input
Blade strokes
(no load)
min-1
cm
1960
1815
Blade length
Blade gap
45
16
50
18
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
mm
s
z
Blade brake time
Weight
<1
2.1
<1
2.4
kg
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 73 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 93 dB(A), uncertainty (K) 3 dB(A)
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah, D) 2.3 m/s2, uncertainty (K) 1.5 m/s2
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
8
(Original instructions)
ENGLISH
EC declaration of conformity
MACHINERY DIRECTIVE
Guarantee
OUTDOOR NOISE DIRECTIVE
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
%
GT4245 / GT4550
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-15
2000/14/EC, Hedge trimmer 1960 min-1, Annex V
The product has been used for trade, professional or hire
purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign
objects, substances or accidents;
Measured sound power (LpA) 93 dB(A)
Uncertainty (K) 3 dB(A)
Guaranteed sound power (LpA) 96 dB(A)
Uncertainty (K) 3 dB(A)
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
These products also comply with directive
2004/108/EC and 2011/65/EU.
For more information, please contact Black & Decker at the
To claim on the guarantee, you will need to submit proof of
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
indicated in this manual. Alternatively, a list of authorised
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
_
United Kingdom
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
06/12/2012
9
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Slough, Berkshire SL1 3YD
90579346 REV-1
12/2012
|