York Csa Dh 036 User Manual

254597-YTG-B-0507

DESCRIPTION

YORK Sunline Ultra units are convertible single package air

conditioners with a common cabinet and a common roof curb

for the 3, 4 and 5 ton sizes. The units were designed for light

commercial and commercial applications. They can easily be

installed on a roof curb, slab, roof jack or frame.

TECHNICAL GUIDE

All units include:

SINGLE PACKAGE GAS/ELECTRIC UNITS

AND SINGLE PACKAGE

•

Powder Paint finish that meets ASTM-B-117 1000 hour

salt spray standards

•

Permanently lubricated motors

AIR CONDITIONERS

Bottom or side air discharge configuration capability

(field convertible)

DH 036, 048 & 060

3, 4 & 5 NOMINAL TONS

•

Manufactured under the quality standards of ISO9001

12.2 THROUGH 13.2 SEER

•

S implicity Control Board

Copper tube/aluminum fin coils

Easy access to all components

Rigging holes in base rails for lifting

Fork lift slots on three sides

Single point power connection

Complete factory package - tested, charged and wired

CSA agency listing on all units

WARRANTY

•

Factory Limited Parts Warranty

One-year parts warranty

A Five-year parts warranty on the compressor and

electric heat elements.

•

Ten-year parts warranty on the gas-fired heat

exchangers.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

254597-YTG-B-0507

PRODUCT NOMENCLATURE

3-5 Ton Sunline Ultra Model Number Nomenclature

D H 048 N04 A 2 A AA 1 0 1 2 4 A

Product Category

Product Style

D = A/C, Single Pkg., R-22

A = Style A

Product Identifier

Configuration Options (not required for all units)

These four digits will not be assigned until a quote is requested, or an order placed.

H = 12.0 SEER A/C

SS Drain Pan

CPC Controller, DFS, APS

Johnson Controller, DFS, APS

Nominal Cooling Capacity

Honeywell Controller, DFS, APS

036 = 3.0 Ton

048 = 4.0 Ton

060 = 5.0 Ton

Novar Controller, DFS, APS

Simplicity IntelliComfort Controller

Simplicity IntelliComfort Controller w/ModLinc

2" Pleated filters

Heat Type and Nominal Heat Capacity

BAS Ready Economizer (2-10 V.D.C. Actuator without a Controller)

Any Combination of Additional Options that Don’t Have an Option Code Pre-assigned

C00 = Cooling Only. Suitable for Field

Installed Electric Heat

Product Generation

Gas Heat Options

1 = First Generation

N04 = 40 MBH Output Aluminized Steel, 1 Stage (036)

N06 = 60 MBH Output Aluminized Steel, 1 Stage (048)

N08 = 80 MBH Output Aluminized Steel, 1 Stage

(036, 060, 072)

2 = Second Generation

Additional Options

Hinged Filter Door & Toolless Access Cabinet

N10 = 100 MBH Output Aluminized Steel, 1 Stage

(048, 060, 072)

Standard Cabinet

D06 = 60 MBH Output Aluminized Steel, 2 Stage

(036, 048, 060, 072)

D10 = 100 MBH Output Aluminized Steel, 2 Stage

(036*, 048, 060, 072)

AA = None

BA = Hinged Filter Door & Toolless Access Panels

BB = Phase Monitor, Hinged Filter Door & Toolless

Access Panels

BC = Coil Guard, Hinged Filter Door & Toolless

Access Panels

BD = Dirty Filter Switch, Hinged Filter Door &

Toolless Access Panels

BE = Phase Monitor & Coil Guard, Hinged Filter

Door & Toolless Access Panels

BF = Phase Monitor & Dirty Filter Switch, Hinged

Filter Door & Toolless Access Panels

BG = Coil Guard & Dirty Filter Switch, Hinged Filter

Door & Toolless Access Panels

AB = Phase Monitor

AC = Coil Guard

S04 = 40 MBH Output Stainless Steel, 1 Stage (036)

S06 = 60 MBH Output Stainless Steel, 1 Stage (048)

S08 = 80 MBH Output Stainless Steel, 1 Stage

(036, 060, 072)

AD = Dirty Filter Switch

AE = Phase Monitor & Coil Guard

AF = Phase Monitor & Dirty Filter Switch

AG = Coil Guard & Dirty Filter Switch

AH = Phase Monitor, Coil Guard & Dirty Filter Switch

AS = Bottom Drain Connection

RC = Coil Guard & American Flag

TA = Technicoat Condenser Coil

TJ = Technicoat Evaporator Coil

TS = Technicoat Evaporator and Condenser Coil

S10 = 100 MBH Output Stainless Steel, 1 Stage

(048, 060, 072)

T06 = 60 MBH Output Stainless Steel, 2 Stage

(036, 048, 060, 072)

T10 = 100 MBH Output Stainless Steel, 2 Stage

(036*, 048, 060, 072)

BH = Phase Monitor, Coil Guard & Dirty Filter Switch,

Hinged Filter Door & Toolless Access Panels

Electric Heat Options

E05 = 5 KW

E07 = 7 KW

E10 = 10 KW

E15 = 15 KW

E20 = 20 KW

E30 = 30 KW

ZZ = If desired option combination is not listed above, ZZ will be assigned and configuration options will be

located in digits 15-18.

Installation Options

*(D, T) 10 = 92 MBH Output on 036 Models

Airflow

A = No Options Installed

B = Option 1

C = Option 2

D = Options 1 & 2

E = Option 3

A = Direct Drive

B = Direct Drive/Single Input Economizer

D = Direct Drive/Motorized Damper

N = Belt Drive

F = Option 4

G = Options 1 & 3

H = Options 1 & 4

J = Options 1, 2 & 3

K = Options 1, 2, & 4

L = Options 1,3 & 4

M = Options 1, 2, 3, & 4

N = Options 2 & 3

P = Options 2 & 4

Q = Options 2, 3, & 4

R = Options 3 & 4

S = Option 5

P = Belt Drive/Single Input Economizer

R = Belt Drive/Motorized Damper

Voltage

2 = 208/230-3-60

4 = 460-3-60

5 = 575-3-60

T = Options 1 & 5

U = Options 1, 3, & 5

V = Options 1, 4, & 5

W = Options 1, 3, 4, & 5

X = Options 3 & 5

Y = Options 4 & 5

Z = Options 3, 4 & 5

Options

1 = Disconnect

2 = Non-Pwr'd Conv. Outlet

3 = Smoke Detector S.A.

4 = Smoke Detector R.A.

5 = Pwr'd Conv. Outlet

Unitary Products Group

254597-YTG-B-0507

gas valve, if applicable, and the temperature limit

switch on gas heat units. The unit control board will

alarm on ignition failures, compressor lockouts and

repeated limit switch trips.

FEATURES

All models are available with a wide variety of factory-

mounted options such as stainless steel heat exchangers,

electric heaters, phase monitor, convenience outlet, dirty filter

switch, disconnect switch, smoke detectors, and coil guard to

make them suitable for almost every application.

•

Nuisance Trip Protection- To prevent nuisance

trouble calls, the control board uses a “three strikes,

you’re out” philosophy. The high and low-pressure

switches and the freezestats must trip three times

within two hours before the unit control board will

lock out the compressor.

All units are self-contained and assembled on full perimeter

base rails with forklift holes on three sides and holes for over-

head rigging. Every unit is completely piped, wired, charged

and tested at the factory to simplify the field installation and to

provide years of dependable operation.

On Board Diagnostics - Each alarm will energize a

trouble light on the thermostat, if so equipped, and

flash an alarm code on the control board LED. Each

high and low-pressure switch alarm as well as each

freezestat alarm has its own flash code. The control

board saves the five most recent alarms in memory,

and these alarms can be reviewed at any time.

Alarms and programmed values are retained

through the loss of power.

All models (including those with an economizer) are suitable for

either bottom or horizontal duct connections. For bottom duct,

remove the sheet metal panels from the supply and return air

openings through the base of the unit. For horizontal duct,

remove the supply and return air panels on the rear of the unit.

All models are available with these “factory mounted” outdoor

air damper options:

All units have long lasting powder paint cabinets with 1000

hour salt spray test approval under ASTM-B117 procedures.

•

Single enthalpy economizer

Motorized outdoor air damper

All models are CSA listed.

•

Warranty - All models include a one-year limited parts

warranty on the complete unit. Compressors and electric

heater elements carry a five-year warranty. Gas heat

exchangers carry a 10-year parts warranty.

Supply air blowers are equipped with either direct drive or

belt drive that can be adjusted to meet the exact require-

ments of the job.

All compressors are equipped with internal pressure relief.

Every refrigerant circuit includes a liquid line filter-drier, a high

pressure switch and a suction line with a freezestat and low

pressure/loss of charge switch to protect all system compo-

nents.

•

Gas Heat Operation - All single phase models with gas

heat have minimum annual fuel utilization efficiency

(AFUE) of 80%. All three phase models with gas heat

have minimum steady state efficiency of 80%. Each sec-

tion includes a durable heat exchanger with aluminized

steel or optional stainless steel tubes, a redundant gas

valve, spark ignition, power venting, an ignition module

for 100% shut-off and all of the safety controls required

to meet the latest ANSI standards.

•

S implicity Controls - S implicity control boards have

standardized a number of features previously available

only as options or by utilizing additional controls.

•

Low Ambient - An integrated low-ambient control

allows all units to operate in the cooling mode down

to 0ºF outdoor ambient without additional assis-

tance. Optionally, the control board can be pro-

grammed to lockout the compressors when the

outdoor air temperature is low or when free cooling

is available.

The gas supply piping can be routed into the heating

compartment through a hole in the base pan of the unit

or through a knockout in the piping panel on the front of

the unit.

•

Electric Heat Operation - All electric heat models are

wired for a single power source and include a bank of

nickel chromium elements mounted at the discharge of

the supply air blower to provide a high velocity and uni-

form distribution of air across the heating elements.

Every element is fully protected against excessive tem-

perature by thermal limit switches.

•

Anti-Short Cycle Protection - To aid compressor

life, an anti-short cycle delay is incorporated into the

standard controls. Compressor reliability is further

ensured by programmable minimum run times. For

testing, the anti short cycle delay can be temporarily

overridden with the push of a button.

The power supply wiring can be routed into the control

box through a threaded pipe connection (field supplied)

in the base pan of the unit or through a knockout in the

wiring panel on the side of the unit.

•

Fan Delays - Fan on and fan off delays are fully pro-

grammable and are independent of one another. All

units are programmed with default values based

upon their configuration of cooling and heat.

Safety Monitoring - The control board monitors the

high and low-pressure switches, the freezestats, the

Unitary Products Group

254597-YTG-B-0507

FIGURE 1 - UNIT CUTAWAY

•

BAS Controls - York’s Sunline™ series units offer factory

mounted BAS controls such as S implicity INTELLI-Com-

fort™, Novar, Honeywell, Johnson, and CPC.

•

PHENOLIC COATED EVAPORATOR AND CON-

DENSER COILS - Special coating process that utilizes

Technicoat 10-1 processes. Coating is applied by total

immersion of the complete coil for maximum protection.

FACTORY-INSTALLED OPTIONS

•

ELECTRIC HEATERS - Wired for single point power

supply. These nickel chromium heater elements are pro-

vided with limit and automatic reset capability to prevent

operation at excessive temperatures.

SINGLE INPUT ELECTRONIC ENTHALPY ECONO-

MIZERS - Includes a slide-in / plug-in damper assembly

with fully modulating spring-return motor actuator capa-

ble of introducing up to 100% outdoor air with nominal

1% leakage type dampers.

•

FILTER OPTIONS - Standard units are shipped with 1”

throw-away filters installed. 2” pleated filters are offered

as a factory installed option.

The enthalpy system contains one sensor that monitors

the outdoor air and determines when the air is cool

enough and dry enough to provide free cooling.

CONVENIENCE OUTLET - This 110 volt outlet can be

“powered” by the unit with a stepdown transformer or the

unit may be ordered with a “non-powered” convenience

outlet that can be wired in the field.

The rainhood is painted to match the basic unit and must

be field-assembled before installing.

•

DISCONNECT SWITCH - For gas heat units and cooling

units with electric heat, a HACR breaker sized to the unit

is provided. For cooling only units, a switch sized to the

largest electric heat available for the particular unit is

provided. Factory installed option only.

•

MOTORIZED OUTDOOR AIR INTAKE DAMPER -

Includes a slide-in / plug-in damper assembly with a 2-

position, spring return motor actuator which opens to a

pre-set position whenever the supply air blower is oper-

ating and will drive fully closed when the blower unit

shuts down.

BAS - Building Automation System Controls

S implicity INTELLI-Comfort™ CONTROL - The York®

The rain hood is painted to match the basic unit and

must be field assembled before installing.

S implicity INTELLI-Comfort™ control is factory installed.

It includes a supply air sensor, a return air sensor, and an

outside air sensor. There are provisions for a field

Unitary Products Group

254597-YTG-B-0507

installed dirty filter indicator switch, an air-proving switch,

an Outside Air Humidity sensor, a Return Air Humidity

sensor, an Inside IAQ sensor, and an Outside Air IAQ

sensor. Construction mode operation, 365-day real time

clock with 7 day programming plus holiday scheduling is

built-in. Two different modes of demand ventilation are

•

SMOKE DETECTORS - (supply air & return air) The

smoke detectors stop operation of the unit by interrupting

power to the control board if smoke is detected within the

air compartment.

achieved through the INTELLI-Comfort™ using CO sen-

sors. It uses an inside CO sensor to perform Demand

Ventilation. It can also use an Outside CO sensor to per-

Factory installed Smoke Detectors in the return air,

may be subjected to freezing temperatures during

“off” times due to outside air infiltration. These

smoke detectors have an operational limit of 32°F

to 131°F. Smoke detectors installed in areas that

could be outside those limitations will have to be

moved to prevent having false alarms.

form Differential Demand Ventilation. It uses a Patented

Comfort Ventilation algorithm to provide comfortable ven-

tilation air temperature. The patented economizer-loading

algorithm will protect the equipment when harsh operating

conditions exist. Humidity in the occupied space or return

duct can be monitored and controlled via humidity sen-

sors and the on-board connection for hot gas re-heat sys-

tem. It uses the INTELLI-Start™ algorithm to maximize

energy savings by recovering the building from the Unoc-

cupied Setpoints to the Occupied Setpoints just in time for

•

COIL GUARD - Customers can purchase a coil guard kit

to protect the condenser coil from damage. This is not a

hail guard kit.

the Occupied Time Period to begin. The S implicity

INTELLI-Comfort™ balances space temperature, ventila-

STAINLESS STEEL HEAT EXCHANGER - For applica-

tions in corrosive environments, this option provides a

full stainless steel heat exchanger assembly.

tion air temperature, CO and humidity for ultimate com-

fort.

•

S implicity INTELLI-Comfort™ with MOD LINK CON-

STAINLESS STEEL DRAIN PAN - An optional rust-

proof stainless steel drain pan is available to provide

years of trouble-free operation in corrosive environ-

ments.

TROL - The York® S implicity INTELLI-Comfort™ with

Mod Link control is factory installed. It includes all the

features of the INTELLI-Comfort™ control with an addi-

tional control to translate communications from MOD-

BUS to the BACnet MSTP protocol.

•

BOTTOM DRAIN CONNECTION - An optional bottom

drain connection is available for inside the curb connec-

tions for applications in cold environments to reduce

freezing drain lines.

•

Novar® BAS CONTROL - The Novar® ETC-3 building

automation system controller is factory installed.

Includes supply air sensor, return air sensor, dirty filter

indicator switch, and air proving switch.

•

PHASE MONITORS - Designed to prevent unit damage.

The phase monitor will shut the unit down in an out-of-

phase condition.

JOHNSON CONTROLS BAS CONTROL - The Johnson

Control YK-UNT-1126 building automation system con-

troller is factory installed. Includes supply air sensor,

return air sensor, dirty filter indicator switch, and air prov-

ing switch.

DIRTY FILTER SWITCH - This kit includes a differential

pressure switch that energizes the fault light on the unit

thermostat, indicating that there is an abnormally high

pressure drop across the filters. Factory installed option

or field installed accessory.

•

CPC BAS CONTROL - The Computer Process Controls

Model 810-3060 ARTC Advanced Rooftop building auto-

mation system controller is factory installed. Includes

supply air sensor, return air sensor, dirty filter indicator

switch and air proving switch.

•

HINGED FILTER DOOR/“TOOLLESS” BLOWER AND

ACCESS PANELS (not hinged) - This option allows for

easy access and maintenance.

NOTE:Knobs are shipped inside the unit to prevent ship-

ping damage. These must be field installed for

tool-less operation.

HONEYWELL BAS CONTROL - The Honeywell

W7750C building automation system controller is factory

installed. Includes air supply sensor, return air sensor,

dirty filter indicator switch, and air proving switch.

Unitary Products Group

254597-YTG-B-0507

tudes up to 6,000 feet. This accessory supplements the

basic propane conversion kit.

FIELD-INSTALLED ACCESSORIES

•

SINGLE INPUT ELECTRONIC ENTHALPY ECONO-

MIZERS - Includes a slide-in / plug-in damper assembly

with fully modulating spring-return motor actuator capa-

ble of introducing up to 100% outdoor air with nominal

1% leakage type dampers.

•

LOW NOX KIT - Required to reduce the emission of

nitrogen oxides below 40 nano grams per joule.

POWER EXHAUST - Our single input economizer

options are available with power exhaust. Whenever the

outdoor air intake dampers are opened for free cooling,

the exhaust fan will be energized to prevent the condi-

tioned space from being over-pressurized during econo-

mizer operation.

The enthalpy system contains one sensor that monitors

the outdoor air and determines when the air is cool

enough and dry enough to provide free cooling.

The rainhood is painted to match the basic unit and must

be field-assembled before installing.

The power exhaust option can only be used on bot-

tom duct configurations.

•

MOTORIZED OUTDOOR AIR INTAKE DAMPER -

Includes a slide-in / plug-in damper assembly with a 2-

position, spring return motor actuator which opens to

some pre-set position whenever the supply air blower is

operating and will drive fully closed when the blower unit

shuts down.

•

BAROMETRIC RELIEF DAMPER - This damper acces-

sory can be used to relieve internal building air pressure

on units with an economizer without power exhaust. This

accessory includes a rain hood, a bird screen and a fully

assembled damper. With bottom duct connections, the

damper should be mounted over the opening in the

return air panel. With horizontal ductwork, the accessory

should be mounted on the return air duct.

The rain hood is painted to match the basic unit and

must be field assembled before installing.

•

ELECTRIC HEATERS wired for single point power sup-

ply. These nickel chromium heater elements are pro-

vided with limit and automatic reset capability to prevent

operation at excessive temperatures.

•

ENTHALPY ACCESSORY CONTROL KIT - This kit

contains the required components to convert a single

enthalpy economizer to dual enthalpy.

•

BURGLAR BARS - Mount in the supply and return

openings to prevent entry into the duct work.

ROOF CURBS - Eight and fourteen-inch high roof curbs

provide a water-tight seal between the unit and the fin-

ished roof. These full perimeter curbs meet the require-

ments of the National Roofing Contractors Association

(NRCA) and are shipped knocked-down for field assem-

bly.

FLUE EXHAUST EXTENSION KIT - In locations with

wind or weather conditions which may interfere with

proper exhausting of furnace combustion products, this

kit can be installed to prevent the flue exhaust from

entering nearby fresh air intakes.

Roof curbs are designed to fit inside the base rails of the

unit and include both a wood nailing strip and duct

hanger supports.

•

CO SENSOR - Senses CO levels and automatically

overrides the economizer when levels rise above the

present limits.

•

HIGH ALTITUDE NATURAL GAS - Burner orifices and

pilot orifices are provided for proper furnace operation at

altitudes up to 6,000 feet.

COIL GUARD - Customers can purchase a coil guard kit

to protect the condenser coil from damage. This is not a

hail guard kit.

•

PROPANE - Burner orifices, pilot orifices and gas valve

parts are provided to convert a natural gas furnace to

propane.

HAIL GUARD - Hail Guard kit is available to prevent unit

from hail damage. This is a sloped hood that fits above

the coil.

HIGH ALTITUDE PROPANE - Burner orifices and pilot

orifices are provided for proper furnace operation at alti-

GAS PIPING KIT - This kit supplies all necessary fittings

and shut off valve.

Unitary Products Group

254597-YTG-B-0507

TABLE 1: SOUND POWER RATING

-12

SOUND POWER (db 10

Watts)

Octave Band Centerline Frequency (Hz)

ESP

BLOWER

UNIT

SIZE

dB(A)

10Ft.²

CFM

SWL

dB(A)

IWG SPEED

125

250

500

1,000

2,000

4,000

8,000

036

048

060

1,200

1,600

2,000

0.6

LOW

HIGH

0.60

0.80

1.00

0.55

0.45

1. These values have been accessed using a model of sound propagation from a point source into the hemispheric\free field. The

dBA values provided are to be used for reference only. Calculation of dBA values cover matters of system design and the fan

manufacture has no way of knowing the details of each system. This constitutes and expectation to any specification or guaran-

tee requiring a dBA value or sound data in any other form than sound power level ratings.

2. At a distance of 10 feet from the blower.

TABLE 3: GAS HEAT RATINGS

TABLE 2: CAPACITY RATINGS - (ARI 210/240)

EER²

SEER³

12.25

13.20

12.20

MBH

INPUT

MBH

OUTPUT

AFUE

(%)

TEMP

RISE ºF

MODEL

DH036

DH048

DH060

MBH

MODEL

42.5

46.5

57.0

11.1

DH036N04

DH036N08

100

80.9

80.5

15 - 45

40 - 70

11.4

10.6

DH048N06

DH048N10

125

100

80.9

80.3

25 - 55

45 - 75

1. 80/67°F Indoor and 95°F outdoor.

2. EER = Energy Efficiency Ratio at full load - the cooling

capacity in Btu’s per hour (Btuh) divided by the power

input in watts, expressed in Btuh per watt (Btuh/watt).

3. SEER = Seasonal Energy Efficiency Ratio.

DH060N08

DH060N10

100

125

100

80.5

80.3

25 - 55

35 - 65

1. All units are single-stage heating.

TABLE 4: 2 STAGE GAS HEAT RATINGS

MBH INPUT

MBH OUTPUT

STEADY STATE EFFICIENCY

RISE

MINIMUM HEATING

AIRFLOW (CFM)

MODEL¹

^STSTAGE 2^NDSTAGE 1^STSTAGE 2^NDSTAGE 1^STSTAGE

2^NDSTAGE

MIN. MAX.

115

35.8

55.2

35.7

60.4

35.8

60.4

60.8

79.4

80.0

79.4

80.5

79.4

80.5

81.1

790

950

DH036D06

DH036D10

DH048D06

DH048D10

DH060D06

DH060D10

80.2

60.8

100.6

60.8

100.6

81.1

790

125

80.5

1230

1010

1230

81.1

125

80.5

1. Models are 3Ø only.

Unitary Products Group

254597-YTG-B-0507

TABLE 5: DH036 COOLING CAPACITIES (3 TON)

TEMPERATURE OF AIR ON CONDENSER COIL

AIR ON

85°F

SENSIBLE CAPACITY¹

ENTERING DRY BULB, °F

95°F

SENSIBLE CAPACITY¹

ENTERING DRY BULB, °F

EVAPORATOR

TOTAL

COIL

POWER

CAP.¹

MBH

CAP.¹

MBH

INPUT²kW

CFM

WB °F

55.2

49.1

44.7

42.4

55.2

49.1

44.7

42.4

51.9

46.1

42.0

39.8

49.4

43.9

40.0

37.9

46.9

41.7

38.0

36.0

3.18

3.13

3.05

3.18

3.13

3.05

3.15

3.10

3.02

3.03

3.12

3.07

2.99

3.00

3.09

3.04

2.96

2.97

35.2 30.7 26.2 21.8 17.3

51.5

45.8

41.2

39.9

50.0

44.5

40.0

38.8

48.6

43.2

38.9

37.6

46.4

41.2

37.1

35.9

44.2

39.3

35.4

34.2

3.44

3.35

3.30

3.35

3.41

3.32

3.27

3.32

3.38

3.29

3.23

3.29

3.36

3.27

3.21

3.27

3.34

3.25

3.20

3.25

34.1 29.7 25.2 20.7 16.2

41.7 37.2 32.8 28.3 23.8 19.4 14.9

44.7 43.6 39.1 34.6 30.1 25.7 21.2

42.4 42.4 42.4 37.9 33.4 29.0 24.5

40.2 35.7 31.3 26.8 22.3 17.8 13.4

41.2 41.2 38.8 34.3 29.8 25.3 20.9

39.9 39.9 39.9 35.4 31.0 26.5 22.0

1500

35.2 30.7 26.2 21.8 17.3

31.5 27.5 23.6 19.6 15.6

41.7 37.2 32.8 28.3 23.8 19.4 14.9

44.7 43.6 39.1 34.6 30.1 25.7 21.2

42.4 42.4 42.4 37.9 33.4 29.0 24.5

37.2 33.2 29.2 25.3 21.3 17.3 13.3

40.0 39.2 36.3 32.3 28.3 24.3 20.3

38.8 38.8 37.5 33.5 29.6 25.6 21.6

1350

1200

1050

900

30.0 26.5 23.0 19.5

16.0

28.9 25.4 21.9 18.4 14.9

35.7 32.2 28.7 25.2 21.7 18.2 14.7

41.2 37.7 34.2 30.7 27.2 23.7 20.2

39.8 39.8 37.3 33.8 30.3 26.8 23-3

34.2 30.7 27.2 23.7 20.2 16.7 13.2

38.9 37.2 33.7 30.2 26.7 23.2 19.8

37.6 37.6 35.1 31.6 28.1 24.6 21.1

27.3 24.3 21.2 18.2

15.2

26.2 23.2 20.2 17.2 14.1

32.6 29.6 26.5 23.5 20.5 17.4 14.4

37.7 34.7 31.6 28.6 25.6 22.5 19.5

37.9 37.0 34.5 31.4 28.4 25.4 22.3

31.1 28.1 25.0 22.0 19.0 16.0 12.9

36.2 34.1 31.1 28.0 25.0 22.0 18.9

35.9 34.9 32.3 29.3 26.3 23.2 20.2

24.6 22.1 19.5 16.9 14.4

23.6 21.0 18.4 15.9 13.3

29.5 26.9 24.4 21.8 19.2 16.7 14.1

34.2 31.6 29.1 26.5 23.9 21.4 18.8

36.0 34.2 31.7 29.1 26.5 24.0 21.4

28.0 25.4 22.9 20.3 17.7 15.2 12.6

33.5 30.9 28.4 25.8 23.2 20.7 18.1

34.2 32.1 29.5 27.0 24.4 21.8 19.3

TEMPERATURE OF AIR ON CONDENSER COIL

AIR ON

EVAPORATOR

COIL

105°F

115°F

SENSIBLE CAPACITY¹

TOTAL

POWER

CAP.¹

MBH

CAP.¹

MBH

ENTERING DRY BULB, °F

INPUT²kW

CFM

WB °F

47.6

42.5

38.0

37.4

46.5

41.6

37.1

36.5

45.4

40.6

36.2

35.7

43.2

38.7

34.5

34.0

41.1

36.7

32.8

32.3

3.65

3.56

3.49

3.54

3.62

3.53

3.46

3.52

3.60

3.51

3.44

3.49

3.57

3.48

3.41

3.47

3.54

3.45

3.39

3.44

32.3 27.8 23.3 18.9 14.4

43.6

39.3

34.8

34.9

42.9

38.6

34.2

34.3

42.2

37.9

33.6

33.7

40.1

36.1

32.0

32.1

38.0

34.2

30.3

30.4

3.85

3.76

3.67

3.73

3.83

3.74

3.66

3.72

3.82

3.73

3.64

3.70

3.78

3.69

3.61

3.67

3.75

3.66

3.58

3.64

30.4 26.0 21.5 17.0 12.5

39.0 34.5 30.0 25.6 21.1 16.6 12.1

38.0 38.0 36.6 32.1 27.6 23.1 18.7

37.4 37.4 37.4 32.9 28.5 24.0 19.5

37.8 33.3 28.8 24.3 19.9 15.4 10.9

34.8 34.8 34.4 29.9 25.4 20.9 16.5

34.9 34.9 34.9 30.5 26.0 21.5 17.0

1500

29.7 25.8 21.8 17.8 13.8

28.0 24.0 20.0 16.0 12.0

36.0 32.0 28.0 24.0 20.1 16.1 12.1

37.1 36.6 34.1 30.1 26.1 22.2 18.2

36.5 36.5 35.2 31.2 27.2 23.3 19.3

34.8 30.8 26.8 22.8 18.8 14.9 10.9

34.2 34.0 32.0 28.0 24.0 20.0 16.0

34.3 34.3 32.9 28.9 24.9 21.0 17.0

1350

1200

1050

900

27.2 23.7 20.2 16.7 12.2

25.5 22.0 18.5 15.0 11.5

33.0 29.5 26.0 22.5 19.0 15.5 12.0

36.2 35.2 31.7 28.2 24.7 21.2 17.7

35.7 35.7 33.0 29.5 26.0 22.5 19.0

31.8 28.3 24.8 21.3 17.8 14.3 10.8

33.6 33.1 29.6 26.1 22.6 19.1 15.6

33.7 33.7 30.9 27.4 23.9 20.4 16.9

24.6 21.6 18.5

12.5

22.9 19.9 16.9 13.8 10.8

29.9 26.9 23.8 20.8 17.8 14.7 11.7

33.9 32.1 29.0 26.0 23.0 19.9 16.9

34.0 32.9 30.3 27.2 24.2 21.2 18.1

28.7 25.7 22.6 19.6 16.6 13.5 10.5

31.6 30.0 27.0 23.9 20.9 17.9 14.9

32.1 30.9 28.2 25.1 22.1 19.1 16.0

22.0 19.4 16.8 14.3 11.7

20.4 17.8 15.2 12.7 10.1

26.8 24.2 21.7 19.1 16.5 14.0 11.4

31.5 28.9 26.4 23.8 21.2 18.7 16.1

32.3 30.1 27.5 24.9 22.4 19.8 17.2

25.6 23.0 20.4 17.9 15.3 12.7 10.2

29.5 26.9 24.4 21.8 19.2 16.7 14.1

30.4 28.0 25.4 22.9 20.3 17.7 15.2

1. These capacities are gross ratings. For net capacity, determine the kW of the supply air blower from the SUPPLY AIR BLOWER PERFORMANCE

Tables, multiply this value by 3.415 MBH/kW to determine the motor heat, and deduct this heat from the gross capacity of the unit.

2. These ratings include the compressor and the condenser fan motors but not the supply air blower motor. The total condenser fan motor

power input is 0.36kW. Refer to SUPPLY AIR BLOWER PERFORMANCE Tables for the kW of the supply air blower motor.

NOMINAL RATING

Unitary Products Group

254597-YTG-B-0507

TABLE 6: DH048 COOLING CAPACITIES (4 TON)

TEMPERATURE OF AIR ON CONDENSER COIL

AIR ON

EVAPORATOR

COIL

85°F

SENSIBLE CAPACITY¹

ENTERING DRY BULB, °F

95°F

SENSIBLE CAPACITY¹

ENTERING DRY BULB, °F

TOTAL

POWER

CAP.¹

MBH

CAP.¹

MBH

INPUT²kW

CFM

WB °F

3.3

3.2

3.1

3.3

3.2

3.1

3.3

3.2

3.1

3.2

3.1

3.2

3.1

3.0

3.5

3.4

3.3

3.5

3.4

3.3

3.5

3.4

3.3

3.5

3.4

3.3

3.5

3.4

2000

1800

1600

1400

1200

TEMPERATURE OF AIR ON CONDENSER COIL

AIR ON

EVAPORATOR

COIL

105°F

115°F

SENSIBLE CAPACITY¹

TOTAL

POWER

CAP.¹

MBH

CAP.¹

MBH

ENTERING DRY BULB, °F

INPUT²kW

CFM

WB °F

3.8

3.7

3.6

3.8

3.7

3.6

3.8

3.7

3.6

3.8

3.7

3.6

3.5

3.7

3.6

3.5

4.0

3.8

4.0

3.9

3.8

4.1

3.9

3.8

4.0

3.8

3.7

3.9

3.8

3.7

2000

1800

1600

1400

1200

1. These capacities are gross ratings. For net capacity, determine the kW of the supply air blower from the SUPPLY AIR BLOWER PERFORMANCE

Tables, multiply this value by 3.415 MBH/kW to determine the motor heat, and deduct this heat from the gross capacity of the unit.

2. These ratings include the compressor and the condenser fan motors but not the supply air blower motor. The total condenser fan motor

power input is 0.36kW. Refer to SUPPLY AIR BLOWER PERFORMANCE Tables for the kW of the supply air blower motor.

NOMINAL RATING

Unitary Products Group

254597-YTG-B-0507

TABLE 7: DH060 COOLING CAPACITIES (5 TON)

TEMPERATURE OF AIR ON CONDENSER COIL

AIR ON

EVAPORATOR

COIL

85°F

SENSIBLE CAPACITY¹

ENTERING DRY BULB, °F

95°F

SENSIBLE CAPACITY¹

ENTERING DRY BULB, °F

TOTAL

POWER

CAP.¹

MBH

CAP.¹

MBH

INPUT²kW

CFM

WB °F

4.3

4.2

4.0

4.3

4.2

4.0

4.3

4.2

4.0

4.3

4.2

4.0

4.2

4.1

4.0

4.6

4.5

4.4

4.6

4.5

4.4

4.6

4.5

4.4

4.6

4.5

4.4

4.6

4.5

4.4

2500

2250

2000

1750

1500

TEMPERATURE OF AIR ON CONDENSER COIL

AIR ON

EVAPORATOR

COIL

105°F

115°F

SENSIBLE CAPACITY¹

TOTAL

POWER

CAP.¹

MBH

CAP.¹

MBH

ENTERING DRY BULB, °F

INPUT²kW

CFM

WB °F

5.0

4.8

4.7

4.9

4.8

4.7

4.9

4.8

4.7

4.9

4.8

4.7

4.6

4.9

4.7

4.6

5.3

5.1

5.0

5.3

5.1

5.0

5.2

5.1

5.0

5.2

5.0

4.9

5.2

5.0

4.9

2500

2250

2000

1750

1500

1. These capacities are gross ratings. For net capacity, determine the kW of the supply air blower from the SUPPLY AIR BLOWER PERFORMANCE

Tables, multiply this value by 3.415 MBH/kW to determine the motor heat, and deduct this heat from the gross capacity of the unit.

2. These ratings include the compressor and the condenser fan motors but not the supply air blower motor. The total condenser fan motor

power input is 0.36kW. Refer to SUPPLY AIR BLOWER PERFORMANCE Tables for the kW of the supply air blower motor.

NOMINAL RATING

Unitary Products Group

254597-YTG-B-0507

TABLE 8: SUPPLY AIR BLOWER PERFORMANCE (3 TON BELT DRIVE) - SIDE DUCT APPLICATION

AVAILABLE EXTERNAL STATIC PRESSURE-IWG²

0.40 0.50 0.60

WATTS RPM WATTS RPM WATTS RPM

AIR

FLOW

CFM

UNIT

TONNAGE

0.20

WATTS RPM

0.30

WATTS RPM

0.70

WATTS RPM

0.80

WATTS

RPM

2000

1900

1800

1700

1600

1500

1400

1300

1200

843

817

790

860

775

700

880

854

828

802

925

850

760

670

919

893

867

840

818

1005

920

840

745

956

930

906

881

858

842

833

1065

993

970

944

920

898

882

867

858

847

1145

1030

1008

985

961

940

922

904

893

880

1195

1067

1046

1025

1001

980

962

942

932

1235

1170

1100

1030

950

895

820

785

995

905

815

740

695

650

1065

980

900

820

755

705

665

640

1125

1040

970

890

835

765

725

680

665

916

730

AVAILABLE EXTERNAL STATIC PRESSURE-IWG²

1.10 1.20 1.30

WATTS RPM WATTS RPM WATTS RPM

AIR

FLOW

CFM

UNIT

0.90

WATTS RPM

1.00

WATTS RPM

1.40

WATTS RPM

1.50

TONNAGE

RPM

1103

1085

1064

1040

1020

1003

982

WATTS

2000

1900

1800

1700

1600

1500

1400

1300

1200

1270

1210

1145

1075

1005

945

1102

1081

1060

1044

1024

1010

992

1180

1115

1050

995

920

870

815

1121

1100

1086

1067

1053

1034

1140

1085

1035

965

880

1107

1099

1080

1000

960

970

835

920

953

780

855

905

1. For 208 Volts multiply values by 0.95.

2. Includes allowances for a wet evaporator coil, 1” filters, and the heat exchangers. Refer to STATIC RESISTANCE Table

for resistance values on applications other than gas / electric units with side duct airflows.

TABLE 9: SUPPLY AIR BLOWER PERFORMANCE (4 TON BELT DRIVE) - SIDE DUCT APPLICATION

AVAILABLE EXTERNAL STATIC PRESSURE-IWG²

AIR

UNIT

TONNAGE

FLOW

CFM

0.20

0.30

0.40

0.50

0.60

0.70

WATTS RPM

0.80

RPM

WATTS RPM

WATTS

1235

1170

1100

1030

950

895

820

785

2000

1900

1800

1700

1600

1500

1400

1300

1200

843

817

790

860

775

700

880

854

828

802

925

850

760

670

919

893

867

840

818

1005

920

840

745

956

930

906

881

858

842

833

1065

993

970

944

920

898

882

867

858

847

1145

1030

1008

985

961

940

922

904

893

880

1195

1125

1040

970

890

835

1067

1046

1025

1001

980

962

942

932

995

905

815

740

695

650

1065

980

900

820

755

705

665

640

665

765

725

680

916

730

AVAILABLE EXTERNAL STATIC PRESSURE-IWG²

1.10 1.20 1.30

WATTS RPM WATTS RPM WATTS RPM

AIR

FLOW

CFM

UNIT

0.90

WATTS RPM

1.00

WATTS RPM

1.40

WATTS RPM

1.50

TONNAGE

RPM

1103

1085

1064

1040

1020

1003

982

WATTS

2000

1900

1800

1700

1600

1500

1400

1300

1200

1270

1210

1145

1075

1005

945

1102

1081

1060

1044

1024

1010

992

1180

1115

1050

995

920

870

815

1121

1100

1086

1067

1053

1034

1140

1085

1035

965

880

1107

1099

1080

1000

960

970

835

920

953

780

855

905

1. Models shown at 230/460 Volts with side duct connections.

2. Includes allowances for a wet evaporator coil, 1” filters, and the heat exchangers. Refer to STATIC RESISTANCE Table

for resistance values on applications other than gas / electric units with side duct airflows.

Unitary Products Group

254597-YTG-B-0507

TABLE 10: SUPPLY AIR BLOWER PERFORMANCE (5 TON BELT DRIVE) - SIDE DUCT APPLICATION

AVAILABLE EXTERNAL STATIC PRESSURE-IWG²

AIR

UNIT

FLOW

CFM

0.20

0.30

0.40

0.50

0.60

0.70

WATTS RPM

0.80

WATTS

TONNAGE

RPM

1059

1032

1005

980

930

877

WATTS RPM

1660

2500

2400

2300

2200

2100

2000

1900

1800

1700

1600

1500

1560

1077

1590

1095

1074

1049

1022

983

941

894

855

1630

1114

1094

1069

1044

1010

976

940

903

884

864

1650

1134

1116

1090

1066

1039

1009

980

1158

1140

1116

1090

1064

1040

1014

988

1685

1181

1167

1142

1117

1092

1070

1047

1022

1001

987

1720

1640

1535

1440

1340

1225

1095

970

1405

1054

1470

1525

1370

1190

1080

1000

885

815

1560

1440

1250

1100

1020

940

860

815

770

1595

1475

1350

1160

1050

980

1620

1505

1410

1260

1100

1020

940

1260

1024

1275

1160

1002

1170

1060

957

1070

950

908

975

950

905

925

850

964

948

880

835

910

870

908

805

882

740

926

780

965

830

AVAILABLE EXTERNAL STATIC PRESSURE-IWG²

1.10 1.20 1.30

WATTS RPM WATTS RPM WATTS RPM

AIR

FLOW

CFM

UNIT

0.90

WATTS RPM

1.00

WATTS RPM

1.40

WATTS RPM

1.50

TONNAGE

RPM

WATTS

2500

2400

2300

2200

2100

2000

1900

1800

1700

1600

1500

1193

1170

1148

1121

1100

1079

1058

1035

1020

1004

1665

1580

1480

1385

1285

1180

1060

960

1202

1180

1155

1133

1110

1090

1071

1056

1038

1620

1530

1425

1340

1240

1135

1030

965

1190

1169

1143

1122

1103

1088

1070

1475

1385

1280

1190

1100

1035

925

1205

1178

1158

1134

1118

1101

1445

1330

1240

1140

1065

980

1222

1196

1164

1145

1130

1375

1295

1175

1105

1045

1197

1170

1158

1205

1130

1075

900

1198

1184

1150

1110

860

880

1. Models shown at 230/460 Volts with side duct connections.

2. Includes allowances for a wet evaporator coil, 1” filters, and the heat exchangers. Refer to STATIC RESISTANCE Table

for resistance values on applications other than gas / electric units with side duct airflows.

TABLE 11: SUPPLY AIR BLOWER PERFORMANCE (3-5 TON) SIDE DUCT APPLICATION

AVAILABLE EXTERNAL STATIC PRESSURE - IWG

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

UNIT

MOTOR

TONNAGE SPEED

1535 320 1493 335 1452 349 1416 363 1377 376 1340 390 1299 403 1260 417 1219 430

MED/HI 1444 263 1398 276 1355 290 1315 303 1271 316 1227 329

1179

343

1125

358 1053 374

MED

1300 208 1254 221

1211

1102

908

234

195 1050 207

145 838 158

1166

246

1119

996

258 1070 272 1006 288

939

303

897

313

MED/LOW 1197

171

1049 130

1149

968

183

134

220

930

235

869

248

LOW

2056 636 2017 696 1978 714 1942 734 1906 749 1864 764 1815 769 1728 743 1582 685

MED/HI 1866 539 1832 557 1795 571 1754 585 1722 602 1679 619 1636 638 1582 653 1508 639

MED 1680 408 1641 426 1594 438 1558 455 1517 472 1469 490 1415 505 1370 521 1337 536

MED/LOW 1582 362 1541 380 1495 391 1465 406 1426 423 1377 440 1326 455 1292 469 1247 485

LOW

1300 223 1258 237 1202 247

2256 883 2258 931 2247 950 2223 964 2182 979 2125 971 2044 940 1958 898 1864 854

2119 808 2089 826 2051 844 2014 859 1965 861 1896 843 1801 806

2020 637 1999 656 1985 675 1947 696 1910 715 1876 730 1832 740 1793 756 1725 748

MED/HI 2145 771 2127 784

MED

MED/LOW 1757 413 1713 432 1677 451 1639 468 1597 479 1559 497 1521 513 1472 523

LOW 1570 327 1536 339 1499 356

1. Includes allowances for a wet evaporator coil, 1” filters, and the heat exchangers. Refer to STATIC RESISTANCES Table for resistance values.

2. Side Duct application (230 Volts)

Unitary Products Group

254597-YTG-B-0507

TABLE 12: BELT DRIVE BLOWER MOTOR AND DRIVE DATA

BELT

(NOTCHED)

ADJUSTABLE MOTOR PULLEY

FIXED BLOWER PULLEY

OUTSIDE PITCH

MOTOR

BLOWER

RANGE

(RPM)

MODEL

SIZE

OUTSIDE

DIA.

PITCH

DIA.

PITCH

LENGTH QTY.

(IN.)

DESIG-

NATION

BORE DESIG-

(IN.)

BORE DESIG-

HP FRAME

DIA.

(IN.)

DIA.

(IN.)

NATION

(IN.)

NATION

(IN.)

3 TON

4 TON

5 TON

790/1120 1 1/2

850/1220 1 1/2

1VL40

2.7-3.7

2.4-3.4

5/8

AK61

AK56

5.9

5.4

5.7

5.2

A36

37.3

1. All motors have solid bases and are inherently protected. these motors can be selected to operate into their service factor because they are located

in the moving air, upstream of any heating device.

TABLE 13: STATIC RESISTANCES

RESISTANCE, IWG

DESCRIPTION

CFM

1000

0.07

0.04

0.06

0.08

1200

0.08

0.05

0.07

0.10

1400

0.09

0.06

0.08

0.12

1600

0.11

0.07

0.09

0.14

1800

0.13

0.08

0.11

0.10

0.16

2000

0.15

0.10

0.13

0.11

0.18

2200

0.17

0.12

0.15

0.12

0.20

2400

0.20

0.14

0.17

0.14

0.23

2600

0.23

0.16

0.20

0.16

0.26

2800

0.26

0.19

0.23

0.19

0.29

3000

ECONOMIZER^{1 3}

0.30

0.22

0.26

0.22

0.32

ELECTRIC

7-15KW

20-30KW

HEATERS¹

BOTTOM DUCT CONNECTIONS¹

COOLING ONLY²

1. Deduct these resistance values from the available external static pressure shown in SUPPLY AIR BLOWER PERFORMANCE Tables.

2. Add these resistance values to the available static resistance values on SUPPLY AIR BLOWER PERFORMANCE Tables.

3. The pressure through the economizer is greater for 100% outdoor air than for 100% return air. If the resistance of the return air

duct system is less than 0.25 IWG, the unit will deliver less CFM during full economizer operation.

TABLE 14: ELECTRIC HEATER CFM LIMITATIONS

MINIMUM SUPPLY AIR CFM

UNITMODELSIZE NOMINAL

VOLTAGE

HEATER SIZE NOMINAL KW

TONS

208/230-3-60

460-3-60

1100

1200

1300

1600

1200

1300

1600

1300

1400

1600

575-3-60

208/230-3-60

460-3-60

1300

575-3-60

208/230-3-60

460-3-60

1600

1800

575-3-60

Unitary Products Group

254597-YTG-B-0507

TABLE 15: ELECTRICAL DATA - DH036, 048 & 060 DIRECT DRIVE W/O POWERED CONVENIENCE OUTLET

COMPRESSORS

MIN.

MAX. FUSE/

BRKR

SIZE

(AMPS)

OD FAN

MOTOR

FLA

CONV

OUTLET

FLA

MODEL

TONNAGE

BLOWER

MOTOR

FLA

ELECTRIC HEATER HEATER HEATER CIRCUIT

VOLTAGE

RLA

LRA

MODEL NO.

AMPS

AMPACITY

(AMPS)

26.7

29.4

37.8

51.3

65.2

26.7

32.6

41.9

57.8

73.7

29.3

32.7

41.0

54.5

68.4

29.3

35.8

45.1

61.1

77.0

32.9

41.0

54.5

68.4

90.3

32.9

35.8

45.1

61.1

77.0

102.3

EACH

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

2CE04513025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

2CE04513025

4.0

5.6

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

4.0

5.6

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

11.1

15.5

22.2

33.0

44.1

61.6

12.7

18.0

25.5

38.2

51.0

71.2

100

208-3-60

13.1

110.0

2.3

8.0

0.0

DH036

230-3-60

208-3-60

230-3-60

10.6

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

4.0

5.6

DH048

208-3-60

230-3-60

16.0

137.0

2.3

10.6

0.0

8.0

11.9

15.9

22.2

5.3

7.5

10.6

15.9

21.2

29.6

DH060

110

1. HACR Type per NEC.

2. These electric heaters do not include a fuse box. If a fuse box is required to meet a local code (i.e. Chicago), the fuse block

accessories 2FB04700825 and 2FB04700846 are available for field installation.

Unitary Products Group

254597-YTG-B-0507

TABLE 16: ELECTRICAL DATA - DH036-060 BELT DRIVE W/O POWERED CONVENIENCE OUTLET

COMPRESSORS

MIN.

MAX. FUSE/

BRKR

OD FAN

MOTOR

FLA

CONV

OUTLET

FLA

MODEL

TONNAGE

BLOWER

MOTOR

FLA

ELECTRIC HEATER HEATER HEATER CIRCUIT

VOLTAGE

RLA

LRA

MODEL NO.

AMPS

AMPACITY

(AMPS)

23.9

25.9

34.3

47.8

61.7

23.9

29.1

38.4

54.3

70.2

12.3

13.5

18.4

23.7

32.6

23.9

25.9

34.3

47.8

61.7

23.9

29.1

38.4

54.3

70.2

12.3

13.5

18.4

23.7

32.6

9.4

SIZE

(AMPS)

100

EACH

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510746

2CE04511046

2CE04511546

2CE04512046

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510746

2CE04511046

2CE04511546

2CE04512046

None

2CE04511058

2CE04511558

2CE04512058

None

4.0

5.6

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

208-3-60

13.1

110.0

2.3

5.2

0.0

DH036

(3.0)

230-3-60

460-3-60

208-3-60

13.1

6.7

110.0

54.0

2.3

1.3

2.3

5.2

2.6

5.2

0.0

6.8

8.2

10.1

13.6

19.5

4.0

5.6

12.1

16.4

23.5

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

13.1

110.0

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

230-3-60

13.1

110.0

2.3

5.2

0.0

DH048

(4.0)

6.8

8.2

460-3-60

575-3-60

6.7

5.1

54.0

44.0

1.3

2.6

2.0

0.0

10.1

13.6

19.5

10.6

15.9

21.2

4.0

5.6

8.0

11.9

15.9

22.2

5.3

7.5

12.1

16.4

23.5

10.2

15.3

20.4

11.1

15.5

22.2

33.0

44.1

61.6

12.7

18.0

25.5

38.2

51.0

71.2

15.2

21.6

28.0

27.5

34.3

47.8

61.7

83.5

27.5

29.1

38.4

54.3

70.2

95.5

14.3

18.4

23.7

32.6

46.6

11.0

15.2

21.6

28.0

39.1

2CE04510525

2CE04510725

208-3-60

230-3-60

16.0

137.0

2.3

5.2

0.0

2CE04511025

2CE04511525

2CE04512025

2CE04513025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

2CE04513025

None

2CE04510746

2CE04511046

2CE04511546

2CE04512046

2CE04513046

None

10.6

15.9

21.2

29.6

DH060

(5.0)

6.8

8.2

10.1

13.6

19.5

28.8

10.6

15.9

21.2

30.4

12.1

16.4

23.5

34.6

10.2

15.3

20.4

29.3

460-3-60

575-3-60

8.3

6.4

69.0

58.0

1.3

2.6

2.0

0.0

2CE04511058

2CE04511558

2CE04512058

2CE04513058

1. HACR Type per NEC.

2. These electric heaters do not include a fuse box. If a fuse box is required to meet a local code (i.e. Chicago), the fuse block

accessories 2FB04700825 and 2FB04700846 are available for field installation.

Unitary Products Group

254597-YTG-B-0507

TABLE 17: ELECTRICAL DATA - DH036, 048 & 060 DIRECT DRIVE W/POWERED CONVENIENCE OUTLET

COMPRESSORS

MIN.

MAX. FUSE/

BRKR

SIZE

(AMPS)

OD FAN

MOTOR

FLA

CONV

OUTLET

FLA

MODEL

TONNAGE

BLOWER

MOTOR

FLA

ELECTRIC HEATER HEATER HEATER CIRCUIT

VOLTAGE

RLA

LRA

MODEL NO.

AMPS

AMPACITY

(AMPS)

36.7

41.9

50.3

63.8

77.7

36.7

38.4

45.1

54.4

70.3

86.2

39.3

39.6

45.2

53.5

67.0

80.9

39.3

41.7

48.3

57.6

73.6

89.5

42.9

45.2

53.5

67.0

80.9

102.8

42.9

48.3

57.6

73.6

89.5

114.8

EACH

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

2CE04513025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

2CE04513025

4.0

5.6

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

4.0

5.6

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

11.1

15.5

22.2

33.0

44.1

61.6

12.7

18.0

25.5

38.2

51.0

71.2

110

208-3-60

13.1

110.0

2.3

8.0

10.0

DH036

230-3-60

208-3-60

230-3-60

10.6

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

4.0

5.6

DH048

208-3-60

230-3-60

16.0

137.0

2.3

10.6

10.0

8.0

11.9

15.9

22.2

5.3

7.5

10.6

15.9

21.2

29.6

DH060

125

1. HACR Type per NEC.

2. These electric heaters do not include a fuse box. If a fuse box is required to meet a local code (i.e. Chicago), the fuse block

accessories 2FB04700825 and 2FB04700846 are available for field installation.

Unitary Products Group

254597-YTG-B-0507

TABLE 18: ELECTRICAL DATA - DH036-060 BELT DRIVE W/POWERED CONVENIENCE OUTLET

COMPRESSORS

MIN.

MAX. FUSE/

BRKR

OD FAN

MOTOR

FLA

CONV

OUTLET

FLA

MODEL

TONNAGE

BLOWER

MOTOR

FLA

ELECTRIC HEATER HEATER HEATER CIRCUIT

VOLTAGE

RLA

LRA

MODEL NO.

AMPS

AMPACITY

(AMPS)

33.9

38.4

46.8

60.3

74.2

33.9

34.9

41.6

50.9

66.8

82.7

17.3

19.7

24.7

29.9

38.8

33.9

38.4

46.8

60.3

74.2

33.9

34.9

41.6

50.9

66.8

82.7

17.3

19.7

24.7

29.9

38.8

13.4

20.2

26.6

33.0

37.5

38.4

46.8

60.3

74.2

96.0

37.5

41.6

50.9

66.8

82.7

108.0

19.3

19.7

24.7

29.9

38.8

52.8

15.0

20.2

26.6

33.0

44.1

SIZE

(AMPS)

100

110

EACH

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510746

2CE04511046

2CE04511546

2CE04512046

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

None

2CE04510746

2CE04511046

2CE04511546

2CE04512046

None

2CE04511058

2CE04511558

2CE04512058

None

4.0

5.6

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

208-3-60

13.1

110.0

2.3

5.2

10.0

DH036

(3.0)

230-3-60

460-3-60

208-3-60

13.1

6.7

110.0

54.0

2.3

1.3

2.3

5.2

2.6

5.2

10.0

5.0

6.8

8.2

10.1

13.6

19.5

4.0

5.6

12.1

16.4

23.5

11.1

15.5

22.2

33.0

44.1

12.7

18.0

25.5

38.2

51.0

13.1

110.0

10.0

8.0

11.9

15.9

5.3

7.5

10.6

15.9

21.2

230-3-60

13.1

110.0

2.3

5.2

10.0

DH048

(4.0)

6.8

8.2

460-3-60

575-3-60

6.7

5.1

54.0

44.0

1.3

2.6

2.0

5.0

4.0

10.1

13.6

19.5

10.6

15.9

21.2

4.0

5.6

8.0

11.9

15.9

22.2

5.3

7.5

12.1

16.4

23.5

10.2

15.3

20.4

11.1

15.5

22.2

33.0

44.1

61.6

12.7

18.0

25.5

38.2

51.0

71.2

2CE04510525

2CE04510725

208-3-60

230-3-60

16.0

137.0

2.3

5.2

10.0

2CE04511025

2CE04511525

2CE04512025

2CE04513025

None

2CE04510525

2CE04510725

2CE04511025

2CE04511525

2CE04512025

2CE04513025

None

2CE04510746

2CE04511046

2CE04511546

2CE04512046

2CE04513046

None

10.6

15.9

21.2

29.6

DH060

(5.0)

6.8

8.2

10.1

13.6

19.5

28.8

10.6

15.9

21.2

30.4

12.1

16.4

23.5

34.6

10.2

15.3

20.4

29.3

460-3-60

575-3-60

8.3

6.4

69.0

58.0

1.3

2.6

2.0

5.0

4.0

2CE04511058

2CE04511558

2CE04512058

2CE04513058

1. HACR Type per NEC.

2. These electric heaters do not include a fuse box. If a fuse box is required to meet a local code (i.e. Chicago), the fuse block

accessories 2FB04700825 and 2FB04700846 are available for field installation.

Unitary Products Group

254597-YTG-B-0507

TABLE 19: PHYSICAL DATA

048

12 X 10

MODELS

Centrifugal Blower (Dia. x Wd. in.)

036

12 X 10

3/4

060

12 X 10

EVAPORATOR

BLOWER

Fan Motor HP (Direct Drive)

Fan Motor HP (Belt Drive)

Rows Deep

1 1/2

EVAPORATOR

COIL

Fins Per Inch

Face Area (Sq. Ft.)

Propeller Dia. (in.)

Fan Motor Hp

4.3

5.1

CONDENSER

FANS

1/2

Nom. CFM

4500

4200

Rows Deep

CONDENSER

COILS

Fins Per Inch

Face Area (Sq. Ft.)

17.1

COMPRESSOR

(Qty. Per Unit)

Recip. Type

Quantity Per Unit (15” X 20” X 1” or 2“)

Quantity Per Unit (14” X 25” X 1” or 2“)

Total Face Area (sq. ft.)

AIR

FILTERS

6.3

Refrigerant 22

(lbs./oz.)

CHARGE

10/8

10/4

10/14

TABLE 20: ELECTRIC HEAT CORRECTION FACTORS

kW CAP.

TABLE 21: VOLTAGE LIMITATIONS

VOLTAGE

NOMINAL VOLTAGE

VOLTAGE

POWER SUPPLY

MULTIPLIER

MIN.

MAX.

208

230

460

575

0.75

0.92

208

240

480

600

208/230-3-60

187

253

460-3-60

575-3-60

414

540

506

630

1. Utilization Range “A” in accordance with ARI Standard

110.

Unitary Products Group

254597-YTG-B-0507

TYPICAL POWER WIRING

TYPICAL CONTROL WIRING

COOLING ONLY (24 VOLT THERMOSTAT)

COOLING / HEATING (24 VOLT THERMOSTAT)

THERMOSTAT¹UNIT TERMINAL

THERMOSTAT¹

TERMINALS

STRIP TB1

UNIT TERMINAL

STRIP TB1

ADD

JUMPER

24 VOLT

TRANSFORMER

24 VOLT

TRANSFORMER

¹24 VOLT THERMOSTAT 2TH07701024. TO CONTROL THE ECONOMIZER

ON SECOND STAGE COOLING, USE THE THERMOSTAT 2TH0401224.

COOLING / HEATING (ELECTRONIC THERMOSTAT)

MULTI STAGE

24 VOLT THERMOSTAT 2ET07701024. TO CONTROL THE ECONOMIZER ON THE SECOND

STAGE COOLING OR TO HAVE AN ELECTRIC HEAT ACCESSORY WITH TWO STAGES OF

HEAT, USE THERMOSTAT 2TH0471024.

THERMOSTAT

TERMINALS

UNIT TERMINAL

STRIP TB1

24 VOLT

TRANSFORMER

ADD

JUMPER

COOLING / HEATING (ELECTRONIC THERMOSTAT)

SINGLE STAGE

THERMOSTAT¹

UNIT TERMINAL

STRIP TB1

TERMINALS

LED 1

ADD

JUMPER

NOT

USED

LED 2

COM

OCC

ADD

JUMPER

24 VOLT

TRANSFORMER

TO REMOTE SENSOR

2TH040702224 IF USED

¹ELECTRONIC PROGRAMMABLE THERMOSTAT 2ET04700224 (INCLUDES SUBBASE).

²SECOND STAGE COOLING IS NOT REQUIRED ON UNITS LESS ECONOMIZER.

¹ELECTRONIC PROGRAMMABLE THERMOSTAT 2ET07701024 (INCLUDES SUBBASE).

TO CONTROL THE ECONOMIZER ON SECOND STAGE COOLING, USE THERMOSTAT

2TH04700224.

³SECOND STAGE HEATING IS ONLY REQUIRED ON UNITS WITH A TWO STAGE

ELECTRIC HEATER OR 2 STAGE GAS HEAT.

REMOVE JUMPER J2 FROM TERMINALS 4 AND 9 ON JUMPER PLUG CONNECTOR

P6 ON UNITS WITH ECONOMIZER. TERMINALS A1 AND A2 PROVIDE A RELAY

OUT-PUT TO CLOSE THE OUTDOOR ECONOMIZER DAMPERS WHEN THE

THERMOSTAT SWITCHES TO THE SET-BACK POSITION.

FIGURE 2 - TYPICAL FIELD POWER & CONTROL WIRING

Unitary Products Group

254597-YTG-B-0507

FIGURE 3 - UNIT DIMENSIONS (3 - 5 TON COOLING ONLY/ELECTRIC HEAT) FRONT VIEW

FIGURE 4 - UNIT DIMENSIONS (3 - 5 TON COOLING/GAS HEAT) FRONT VIEW

Unitary Products Group

254597-YTG-B-0507

DETAIL “A”

FIGURE 5 - UNIT WITH ECONOMIZER RAINHOOD

DETAIL “B”

FIGURE 6 - UNIT WITH FIXED OUTDOOR AIR/MOTORIZED DAMPER RAINHOOD

Unitary Products Group

254597-YTG-B-0507

FIGURE 7 - UNIT DIMENSIONS (REAR VIEW)

TABLE 23: MINIMUM CLEARANCES

LOCATION

CLEARANCE

24” (Cooling/Electric Heat)

32” (Gas Heat)

Front

Rear

12” (Less Economizer)

36” (With Economizer or Fixed

Air/Motorized Damper)

FILTER

ACCESS

BLOWER MOTOR

ACCESS

24” (Less Economizer)

36” (With Economizer)

Left Side (Filter Access)

DOT PLUGS

Right Side (Cond. Coil)

Below Unit¹

24”

0”

FIELD-SUPPLIED

DISCONNECT SWITCH

LOCATION

72” (For

Condenser Air Discharge)

Above Unit²

MOUNTING BRACKET

FOR DICONNECT SWITCH

(Shipped attached to the

blower housing inside

A,B

the blower compartment)

1. Units may be installed on combustible floors made

from wood or class A, B, or C roof covering material.

2. Units must be installed outdoors. Overhanging struc-

tures or shrubs should not obstruct condenser air dis-

charge outlet.

WIRING ENTRY

(See Detail “B”)

CONTROL BOX

ACCESS

DISCONNECT SWITCH LOCATION

AND MOTOR ACCESS PANEL FOR

UNIT WITH “BELT-DRIVE” OPTION

FIGURE 8 - DISCONNECT/BLOWER ACCESS

LOCATION

TABLE 22: UTILITIES ENTRY

HOLE

OPENING SIZE (DIA.)

USED FOR

Side

Bottom

Side

7/8” KO

Control Wiring

Power Wiring

2” KO

Bottom

1-5/8” KO

1-1/2” KO

Gas Piping (Front)

Gas Piping (Bottom)

1. Opening in the bottom to the unit can be located by the

side in the insulation.

2. Do not remove the 2” knockout ring.

Unitary Products Group

254597-YTG-B-0507

FIGURE 9 - TYPICAL APPLICATIONS

Unitary Products Group

254597-YTG-B-0507

BACK OF UNIT

44 /₈

82 /₄

APPROXIMATE

CENTER OF GRAVITY

CONDENSER COIL

END OF UNIT

CONDENSER COIL

END OF UNIT

FRONT OF UNIT

FIGURE 10 - FOUR AND SIX POINT LOADING

TABLE 24: DH 4 AND 6 POINT LOADS WEIGHT DISTRIBUTION

4-Point Loading (lb)

6-Point Loading (lb)

UNIT

TOTAL

125

134

137

139

141

135

147

151

143

154

157

159

123

132

134

136

138

133

144

148

141

152

154

156

157

168

171

173

176

169

183

189

179

193

196

198

160

171

174

177

179

172

186

192

182

196

199

202

104

112

113

115

117

112

122

125

119

128

130

132

105

113

115

117

119

114

123

127

120

130

132

133

107

114

116

118

120

115

125

128

122

131

133

135

DH036 Cooling/ Electric

DH036N04

565

605

615

625

635

610

660

680

645

695

705

715

DH036D06

DH036N08

DH036D10

DH048 Cooling/ Electric

DH048(D,N)06

DH048(D,N)10

DH060 Cooling/ Electric

DH060D06

101

100

103

105

106

102

103

105

101

102

104

DH060N08

DH060(D,N)10

TABLE 25: CENTER OF GRAVITY

DIMENSION

3 - 5 TON

40-¾”

19-¾”

Unitary Products Group

254597-YTG-B-0507

TABLE 26: OPERATING WEIGHTS (LBS.)

MODEL SIZE

DH (Cooling Only)

3 TON

565

605

4 TON

5 TON

645

610

N04

N06

N08

N10

D06

D10

660

BASIC

UNIT

625

705

715

695

715

(Gas/Electric)

680

660

680

615

635

Economizer

Motorized Damper

OPTIONS

ACCY.

5 - 7 kW

10 - 15 kW

20 - 30 kW

Electric Heater

Roof Curb

Barometric Relief / Fixed Air Damper

Belt-Drive Blower

FIGURE 11 - ROOF CURB DIMENSIONS

Unitary Products Group

254597-YTG-B-0507

UNIT CABINET

GUIDE SPECIFICATIONS

Unit cabinet shall be constructed of G90 galvanized steel,

with exterior surfaces coated with a non-chalking, powdered

GENERAL

Units shall be manufactured by York International Unitary

Products Group in an ISO 9001 certified facility.

paint finish, certified at 1000 hours salt spray test per

ASTMB117 standards. Indoor blower section shall be insu-

lated with a minimum 1/2” thick insulation, coated on the air-

side. Aluminum foil faced insulation shall be used in the

furnace compartment and be fastened with ridged fasteners

to prevent insulation from entering the air stream. Cabinet

panels shall be “large” size, easily removable for servicing

and maintenance. Full perimeter base rails shall be provided

to assure reliable transit of equipment, overhead rigging and

proper sealing on roof curb applications. Disposable 1" filters

shall be furnished and be accessible through a removable

access door, sealed airtight. Units filter track shall be

designed to accommodate either 1" or 2" filters. Fan perfor-

mance measuring ports shall be provided on the outside of

the cabinet to allow accurate air measurements of evaporator

fan performance without removing panels or creating air by-

pass of the coils. Condensate pan shall be internally sloped

and conform to ASHRAE 62-89 self-draining standards. Con-

densate connection shall be a minimum of 3/4” I.D. female

and be a ridged mount connection.

York's Sunline Ultra units are convertible single package

units. Although the units are primarily designed for curb

mounting on a roof, they can also be slab-mounted at ground

level or set on steel beams above a finished roof. Cooling

only, cooling with gas heat and cooling with electric heat

models are available with a wide variety of factory-mounted

options and field-installed accessories to make them suitable

for almost every application. All units are self-contained and

assembled on full perimeter base rails with holes in the four

corners for overhead rigging. Every unit is completely piped,

wired, charged and tested at the factory to simplify the field

installation and to provide years of dependable operation. All

models (including those with an economizer) are suitable for

either bottom or horizontal duct connections. Models with

power exhaust are suitable for bottom duct connections only.

For bottom duct, remove the sheet metal panels from the

supply and return air openings through the base of the unit.

For horizontal duct, remove the supply and return air panels

on the rear of the unit.

INDOOR (EVAPORATOR) FAN ASSEMBLY

The indoor fan shall be a factory installed with either direct

drive or belt drive assembly that includes an adjustable pitch

motor pulley. Job site selected brake horsepower (B.H.P.)

shall not exceed the motors nameplate horsepower rating,

plus the service factor. Units shall be designed not to operate

above service factor. Fan wheel shall be double-inlet type

with forward-curved blades, dynamically balanced to operate

smoothly throughout the entire range of operation. Airflow

design shall be constant air volume. Bearings shall be sealed

and permanently lubricated for longer life and no mainte-

nance.

All non-Scroll compressors include crankcase heaters and all

compressors have internal pressure relief. Every refrigerant

circuit includes a liquid line filter-drier, a discharge line high

pressure switch and a suction line with a freezestat and low

pressure/loss of charge switch.The unit control circuit

includes a 75 VA transformer, a 24-volt circuit breaker and a

relay board with a compressor lockout circuit, a terminal strip

for thermostat wiring, plus an additional set of pin connectors

to simplify the interface of additional field controls. All units

have long lasting powder paint cabinets with 1000 hour salt

spray test approval under ASTMB117 procedures. All models

are CSA listed. All models include a 1-year limited warranty

on the complete unit. Compressors and electric heater ele-

ments carry a 5-year warranty. Aluminized steel and Stainless

steel tubular heat exchangers carry a 10-year warranty.

OUTDOOR (CONDENSER) FAN ASSEMBLY

The outdoor fan shall be of the direct-driven propeller type,

discharge air vertically, have aluminum blades riveted to a

corrosion resistant steel spider bracket and shall be dynami-

cally balanced for smooth operation. The outdoor fan motor

shall be totally enclosed with permanently lubricated bear-

ings, internally protected against overload conditions and

staged independently.

DESCRIPTION

Units shall be factory-assembled, single packaged, Electric

Cooling/Gas Heat, Electric Cooling/Optional Electric Heat

and designed for outdoor mounted installation.

The 3 ton, 4 ton and 5 ton units shall have minimum SEER

ratings of 12.2, 13.2 and 12.2 respectively. They shall have

built-in field convertible duct connections for down discharge

supply/return or horizontal discharge supply/return, and be

available with factory installed options or field installed acces-

sories. The units shall be factory wired, piped, charged with

R-22 refrigerant and factory tested prior to shipment. All unit

wiring shall be both numbered and color coded. All units the

cooling performance shall be rated in accordance with DOE

and ARI test procedures. Units shall be CSA listed, classified

to ANSI Z21.47, UL 1995/CSA No. 236 standards.

REFRIGERANT COMPONENTS

Compressor:

a. Shall be internally protected with internal high-pres-

sure relief and over temperature protection.

b. Shall have internal spring isolation and sound muf-

fling to minimize vibration and noise, and be exter-

nally isolated on a dedicated, independent

mounting.

Unitary Products Group

254597-YTG-B-0507

Coils:

a. Evaporator and condenser coils shall have alumi-

GAS HEATING SECTION (SINGLE OR 2 STAGE)

Shall be designed with induced draft combustion with post

purge logic, energy saving direct spark ignition, and redun-

dant main gas valve. Venter wheel shall be constructed of

stainless steel for corrosion resistance. The heat exchanger

shall be of the tubular type, constructed of T1-40 aluminized

steel for corrosion resistance and allowing minimum mixed

air entering temperature of 25°F. Burners shall be of the

inshot type, constructed of aluminum coated steel and con-

tain air mixture adjustments. All gas piping shall enter the unit

cabinet at a single location through either the side or curb

without any field modifications. Integrated control boards

shall provide timed control of evaporator fan functioning and

burner ignition. Heating section shall be provided with the fol-

lowing minimum protection:

num plate fins mechanically bonded to seamless

internally enhanced copper tubes with all joints

brazed. Special Phenolic coating shall be available

as a factory option.

b. Evaporator and Condenser coils shall be of the

direct expansion, draw-thru, design.

Refrigerant Circuit and Refrigerant Safety Components shall

include:

a. Thermal expansion devices (TXV’s).

b. Filter drier/strainer to eliminate any moisture or for-

eign matter.

a. Primary and auxiliary high-temperature limit

switches.

c. Accessible service gage connections on both suc-

tion and liquid lines to charge, evacuate, and mea-

sure refrigerant pressure during any necessary

servicing or troubleshooting, without losing charge.

b. Induced draft motor speed sensor.

c. Flame roll out switch.

d. The refrigeration system shall provide at least 15°F

of sub-cooling at design conditions.

d. Flame proving controls.

e. If any of the above safety devices trip, a LED (light-

emitting diode) indicator shall flash a diagnostic

code that indicates which safety switch has tripped.

UNIT CONTROLS

a. Unit shall be complete with self-contained low-volt-

age control circuit protected by a resetable circuit

breaker on the 24-volt transformer side.

ELECTRIC HEATING SECTION

An electric heating section, with nickel chromium elements,

shall be provided in a range of 5 thru 30 KW, offering two

stages of capacity - 16 KW and above on 208/230 volt heaters

and 20 KW and above on 460 and 575 volt heaters. The heat-

ing section shall have a primary limit control(s) and automatic

reset to prevent the heating element system from operating at

an excessive temperature. The heating section assembly

shall slide out of the unit for easy maintenance and service.

Units with Electric Heating shall be wired for a single point

power supply with branch circuit fusing (where required).

b. Unit shall incorporate a lockout circuit which pro-

vides reset capability at the space thermostat or

base unit, should any of the following standard

safety devices trip and shut off compressor.

c. Loss-of-charge/Low-pressure switch.

d. High-pressure switch.

e. Freeze-protection thermostat, evaporator coil.

f. If any of the above safety devices trip, a LED (light-

emitting diode) indicator shall flash a diagnostic

code that indicates which safety switch has tripped.

UNIT OPERATING CHARACTERISTICS

a. Unit shall be capable of starting and running at 125°F

outdoor temperature, exceeding maximum load crite-

ria of ARI Standard 210/240. The compressor, with

standard controls, shall be capable of operation

down to 0°F outdoor temperature. Unit shall be pro-

vided with fan time delay to prevent cold air delivery

before heat exchanger warms up (Gas heat only).

g. Unit shall incorporate “AUTO RESET” compressor

over temperature, over current protection.

h. Unit shall operate with conventional thermostat

designs and have a low voltage terminal strip for

easy hook-up.

Unit control board shall have on-board diagnostics

and fault code display.

ELECTRICAL REQUIREMENTS

All unit power wiring shall enter unit cabinet at a single factory

provided location and be capable of side or bottom entry, to

minimize roof penetrations and avoid unit field modifications.

Separate side and bottom openings shall be provided for the

control wiring.

Standard controls shall include anti-short cycle and

low voltage protection, and permit cooling operation

down to 0°F.

k. Control board shall monitor each refrigerant safety

switch independently.

Control board shall retain last 5 fault codes in non

volatile memory which will not be lost in the event of

a power loss.

Unitary Products Group

254597-YTG-B-0507

STANDARD LIMITED WARRANTIES

OTHER PRE-ENGINEERED ACCESSORIES AVAILABLE

•

Compressor 5 Years

•

ROOF CURB - 14"and 8” high, full perimeter curb with

wood nailer (shipped knocked-down).

Heat Exchanger 10 Years

Electric Heat Element 5 Years

Other Parts 1 Year

•

BAROMETRIC RELIEF DAMPER - Contains a rain

hood, air inlet screen, exhaust damper and mounting

hardware. Used to relieve internal air pressure through

the unit.

OPTIONAL OUTDOOR AIR (Shall be made available by

either/or):

•

PROPANE CONVERSION KIT - Contains new orifices

and gas valve parts to convert from natural to L.P. gas.

One per unit required.

•

ELECTRONIC ENTHALPY AUTOMATIC ECONO-

MIZER- Outdoor and return air dampers that are inter-

locked and positioned by a fully-modulating, spring

return damper actuator. The maximum leakage rate for

the outdoor air intake dampers shall not exceed 2%

when dampers are fully closed and operating against a

pressure differential of 0.5 IWG. A unit-mounted potenti-

ometer shall be provided to adjust the outdoor and return

air damper assembly to take in CFM of outdoor air to

meet the minimum ventilation requirement of the condi-

tioned space during normal operation. During econo-

mizer operation, a mixed-air temperature control shall

modulate the outdoor and return air damper assembly to

prevent the supply air temperature from dropping below

55°F. Changeover from compressor to economizer oper-

ation shall be provided by an integral electronic enthalpy

control that feeds input into the basic module. The out-

door intake opening shall be covered with a rain hood

that matches the exterior of the unit. Water eliminator/fil-

ters shall be provided. Simultaneous economizer/com-

pressor operation is also possible. Dampers shall fully

close on power loss.

HIGH ALTITUDE - NATURAL GAS - Contains orifices

required for applications between 2000 and 6000 feet

altitude.

HIGH ALTITUDE - PROPANE GAS - Contains orifices

required for applications between 2000 and 6000 feet

altitude. Must be used with propane conversion kit.

•

LOW NOX - Required to reduce the emission of nitrogen

oxides below 40 nanograms per joule.

GAS PIPING - Contains 1/2” pipe nipples, fittings and

gas cock (including panel assess gaskets) required for

bottom gas supply connection with external shut off.

•

POWER EXHAUST OPTION - To work in conjunction

with economizers.

•

ELECTRIC HEATERS

•

ECONOMIZER/MOTORIZED DAMPER RAIN HOOD -

Contains all hood panels and the hardware for assem-

bling.

•

MOTORIZED OUTDOOR AIR DAMPERS - Outdoor air

dampers are positioned by a 2-position, spring-return

damper actuator. The maximum leakage rate for the out-

door air intake dampers shall not exceed 2% when

dampers are fully closed and operating against a pres-

sure differential of 0.5 IWG. A unit-mounted potentiome-

ter shall be provided to adjust the outdoor damper

assembly to take in the design CFM of outdoor air to

meet the ventilation requirements of the conditioned

space during normal operation. Whenever the indoor fan

motor is energized, the dampers open up to one of two

pre-selected positions - regardless of the outdoor air

enthalpy. Dampers return to the fully closed position

when the indoor fan motor is de-energized. Dampers

shall fully close on power loss.

•

MANUAL OUTDOOR AIR DAMPER

COIL GUARD KIT - Guard for cooling coil.

HAIL GUARD

FLUE EXHAUST EXTENSION

OTHER FACTORY INSTALLED OPTIONS

•

POWER EXHAUST OPTION - To work in conjunction

with economizers.

•

STAINLESS STEEL HEAT EXCHANGER

STAINLESS STEEL DRAIN PAN

BOTTOM DRAIN CONNECTION

Unitary Products Group

254597-YTG-B-0507

•

TECHNICOAT PHENOLIC COATED CONDENSER

AND EVAPORATOR COIL

•

BAS CONTROLS (S implicity INTELLI-Comfort™,

CPC, JOHNSON, HONEYWELL, NOVAR)

•

ELECTRONIC SINGLE ENTHALPY ECONOMIZER

DIRTY FILTER SWITCH

BAS READY ECONOMIZER (2-10 V.D.C. ACTUATOR

WITHOUT A CONTROLLER)

HINGED FILTER DOOR ACCESS AND TOOLESS

ACCESS PANELS

PHASE MONITOR

COIL GUARD

•

2" PLEATED FILTERS

POWERED GFI CONVENIENCE OUTLET

NON-POWERED GFI CONVENIENCE OUTLET

DISCONNECT SWITCH

SUPPLY AIR SMOKE DETECTOR

RETURN AIR SMOKE DETECTOR

Unitary Products Group

254597-YTG-B-0507

Unitary Products Group

Subject to change without notice. Printed in U.S.A.

254597-YTG-B-0507

Supersedes: 254597-YTG-A-0306

Unitary

Products

Group

5005

York

Drive

Norman

73069

Philips Tea1104 User Manual
Ryobi P541 User Manual
Sears 47003 User Manual
Sharp Al 2030 User Manual
Silva Battery Charger Solar Panel User Manual
Silvercrest Sul 1000 A1 User Manual
Soleus Air Air Conditioner 21 User Manual
Soleus Air Kfh 18 User Manual
Whirlpool 3pach21dd0 User Manual
York D2eb030 User Manual