Sharp Mx B201d User Manual

MODEL: MX-B201D  
2. LOADING PAPER  
Raise the handle of the paper tray and  
pull the paper tray out until it stops.  
Rotate the pressure plate lock in the direction  
of the arrow to remove it while pressing down  
the pressure plate of the paper tray.  
Store the pressure plate lock which has been  
removed in step 2. To store the pressure plate  
lock, rotate the lock to fix it on the relevant  
location.  
1
2
3
DIGITAL MULTIFUNCTIONAL SYSTEM  
START GUIDE  
This guide explains how to install the machine, and indicates important points to note for installation and usage. Read and understand this guide to  
ensure that you install the machine correctly. The Operation Guide for the machine is on the accompanying CD-ROM. The procedure for viewing the  
guide is explained in "4. HOW TO USE THE OPERATION GUIDE". After installation, read the Operation Guide to make full use of all the machine  
has to offer.  
1. TONER CARTRIDGE REPLACEMENT  
When toner is low, the error indicator will light up and "TONER CARTRIDGE IS NEAR EMPTY." will appear in the display to alert you to purchase a  
new toner cartridge. on purchasing a new toner cartridge. If copying is continued while the indicator is lit, copies will gradually become lighter until  
the toner runs out. When the toner runs out, the machine will stop operating, the error indicator will blink, and "REPLACE THE TONER  
CARTRIDGE" will appear in the display. Follow the procedure below to replace the toner cartridge.  
Squeeze the lever of paper guide (A) and slide  
the guide to match with the width of the paper.  
Move paper guide (B) to the appropriate slot  
as marked on the tray.  
Fan the paper and insert it into the tray.  
Make sure the edges go under the  
corner hooks.  
Gently push the paper tray back into the unit.  
4
5
6
• Be sure that paper is free of rips, dust,  
wrinkles, and curled or bent edges.  
• Make sure all the paper in the stack is  
the same size and type.  
• When loading paper, ensure there is no  
space between the paper and the  
guide, and check if the guide is not set  
too narrow causing the paper to bend.  
Loading paper in these ways will result  
in document skew or a paper jam.  
• After the machine stops, it may be possible to make a few more copies by taking the toner cartridge out of the machine, shaking it horizontally,  
then reinstalling it. If copying is not possible after this operation, replace the toner cartridge.  
• During a long copy run of a dark original, "TONER REPLENISHMENT IN PROGRESS" appears in the display, and the machine may stop even  
though toner is left. The machine will feed toner up to 2 minutes and then the ready indicator will light up. Press the [START] key (  
resume copying.  
) to  
Open the bypass tray, and then  
open the side cover while pressing  
the side cover open button.  
Push gently on both sides of the  
front cover to open the cover.  
Gently pull the toner cartridge out while pressing the lock  
release lever.  
1
2
3
(B)  
(A)  
Toner cartridge lock release lever  
• After removing the toner cartridge, do not shake it or  
tap on it. Doing so may cause toner to leak from the  
cartridge. Put the old cartridge immediately in the bag  
contained in the box of the new cartridge.  
• Dispose of the old toner cartridge in accordance with  
local regulations.  
3. POWER ON AND OFF  
Remove the toner cartridge from the bag.  
Grasp the cartridge on both sides and shake  
it horizontally four or five times. After  
shaking the cartridge, remove the toner  
seal.  
Gently insert the toner cartridge along the  
guides until it locks in place while pushing  
the lock release lever.  
Remove the tape from the shutter. Pull the  
shutter out of the toner cartridge as shown  
in the illustration. Discard the shutter.  
Close the front cover and then the side  
cover by pressing the round projections  
near the side cover open button. The error  
indicator will go out and the ready indicator  
will light up.  
4
5
6
If you use the unit in a country other than the country where the unit was purchased, you will need to make sure that your local power supply is  
compatible with your model. If you plug the unit into an incompatible power supply, irreparable damage to the unit will result.  
Turn the power switch on the left side of the unit to the "ON" position.  
Ensure that the power switch of the unit is in the OFF position.  
4 or 5 times  
Shutter  
1
2
ON  
OFF  
The ready indicator will light up and other indicators which show the  
initial settings of the display will also light up to indicate the ready  
condition. For the initial settings, see "Initial settings" on the Operation  
Guide.  
If the power switch is turned off while the machine is in operation, a  
misfeed may occur and the job that was in progress will be canceled. In  
cases where the machine will not be used for a long time, turn off the  
power switch and remove the power cord from the outlet.  
Toner seal  
About the scan head  
The scan head lamp remains on constantly when the unit is in the ready condition (when the start (  
) indicator is illuminated).  
Grasp the toner cartridge as shown in  
the illustration. Do not hold the  
cartridge by the shutter. Be sure to  
only shake the cartridge before the  
toner seal is removed.  
When closing the covers, be sure to  
close the front cover securely and then  
close the side cover. If the covers are  
closed in the wrong order, the covers  
may be damaged.  
The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not  
indicate unit trouble.  
4. HOW TO USE THE OPERATION GUIDE  
Detailed explanations of the functions that can be used on the machine are provided in the Operation Guide in PDF format.  
Even after a new toner cartridge is  
installed, the start (  
) indicator may  
Insert the supplied CD-ROM into your  
computer's CD-ROM drive.  
Display the contents of the CD-ROM, and open  
the Operation Guide file.  
1
2
not light up, indicating copying cannot  
be restarted (toner is not sufficiently  
fed). In this case, open and close the  
side cover. The copier will feed toner  
again approximately 2 minutes and  
then copying can be restarted.  
* To view the Operation Guide in PDF format,  
Adobe® Reader® or Acrobat® Reader® of  
Adobe Systems Incorporated is required.  
Adobe® Reader® can be downloaded from the  
following URL:  
Operation Guide file (PDF)  
Manual  
English  
Operation Guide CD-ROM  
PRINTED IN CHINA 2010L KS1 TINSE2155QSZZ  

One For All Automobile Parts Hfc 302 User Manual
Ryobi P110 User Manual
Samsung Digital Laser Mfp Scx 4216f User Manual
Samsung Sh18zp0 User Manual
Samsung Sh24tp6 User Manual
Soleus Air Gm Pac 12e1 User Manual
Toshiba Air Conditioner Rav Sm1404bt E User Manual
Trane Air Conditioner 4ttx5030a1 User Manual
Whirlpool Acq082 User Manual
Xerox Workcentre C2424 User Manual