Operating Instructions
5.8 GHz Digital Cordless
Answering System
Model No. KX-TG5671
5.8 GHz Expandable Digital Cordless
Answering System with Two Handsets
Model No. KX-TG5672
5.8 GHz Digital Cordless
Answering System with Three Handsets
Model No. KX-TG5673
Model shown is KX-TG5671.
This unit is compatible with Caller ID. To use this feature, you must subscribe to
the appropriate service offered by your service provider.
Charge the handset battery for 7 hours before initial use.
Please read these Operating Instructions before using the unit and save for
future reference.
For assistance, visit our website:
http://www.panasonic.com/phonehelp for customers in the U.S.A. or Puerto
Rico.
Introduction
Introduction
Thank you for purchasing a Panasonic cordless telephone.
We recommend keeping a record of the following information for future reference.
Serial No.
Date of purchase
(found on the bottom of the base unit)
Name and address of dealer
Attach your purchase receipt here.
ENERGY STAR
®
As an ENERGY STAR Participant, Panasonic has determined
that this product meets the ENERGY STAR guidelines for energy
efficiency. ENERGY STAR is a U.S. registered mark.
3
Introduction
About these operating instructions
These operating instructions can be used for KX-TG5671/KX-TG5672/KX-TG5673.
Descriptions of the multiple handsets and chargers
The following models include 2 or more handsets and a charger(s). Descriptions of the
multiple handsets and chargers in these operating instructions are for the following
models only:
KX-TG5672
KX-TG5673
Special feature
®
N Slow Talk
You can slow down the voice of the person you are talking to, making it easier to hear
and understand.
4
Introduction
Symbols used in these operating instructions
Symbol
Meaning
Example: “Ringer ID”
Press {^} or {V} to select the words in quotations
shown on the display.
i
Proceed to the next operation.
Example: {MENU},
{Phonebook}
The words in the brackets indicate button names
including soft key names (page 17) on the handset
and base unit.
Example:
Press {MENU}, then press {0}, {5}, {1}. Press {^}
or {V} to select the desired setting. Press {Save},
then press {OFF}.
{MENU} i {0}{5}{1} i
Select the desired setting. i
{Save} i {OFF}
Expanding your phone system
KX-TG5672 users can expand the system by adding an accessory handset sold
separately (max. 3 handsets).
Accessory handset (up to 1)
KX-TGA560
+
5
Introduction
Accessory information
Included accessories
1
2
3
4
5
6
Quantity
No. Accessory item
Order number
KX-TG KX-TG KX-TG
5671S 5672B 5673B
*1
1
AC adaptor for base unit
PQLV1W or
PQLV256Z
1
1
1
2
3
Telephone line cord
PQJA10075Z
1
1
–
1
1
–
–
–
1
–
1
2
–
2
1
1
1
–
1
3
–
3
2
2
Wall mounting adaptor
PQKL10068Z1
PQKL10068Z2
HHR-P104
4
5
Battery
*2
Handset cover
PQYNTG5631SR
PQYNTG5633BR
PQLV30042ZB
6
Charger
*1
AC adaptor for charger
KX-TCA1-2 or
PQLV256Z
*1 Both of the AC adaptors function well.
*2 The handset cover comes attached to the handset.
6
Introduction
Additional/replacement accessories
Accessory item
Order number
Rechargeable nickel metal
hydride (Ni-MH) battery
HHR-P104
Accessory handset with charger
Headset
KX-TGA560
KX-TCA60, KX-TCA86, KX-TCA88HA, KX-TCA91,
KX-TCA92, or KX-TCA98
T-adaptor
KX-J66
Battery back-up power supply
KX-TCA200
Accessory item
KX-TG5671S
KX-TG5672B
KX-TG5673B
Belt clip
PQKE10396Z1 PQKE10396Z3 PQKE10396Z3
Sales and support information
L To order additional/replacement accessories, call 1-800-332-5368.
L TTY users (hearing or speech impaired users) can call 1-866-605-1277.
7
Introduction
risk of fire or electric shock. Never spill
any liquid on the product.
Important safety
instructions
11. To reduce the risk of electric shock, do
not disassemble the product. Take the
product to an authorized service center
when service is required. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause
electric shock when the product is
subsequently used.
12. Unplug the product from power outlets
and take to an authorized service
center when the following conditions
occur:
When using the product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, or
personal injury.
1. Read all instructions carefully.
2. Follow all warnings and instructions
marked on the product.
3. Unplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners. Use a moist cloth for
cleaning.
4. Do not use the product near water, for
example near a bathtub, wash bowl,
kitchen sink, etc.
5. Place the product securely on a stable
surface. Serious damage and/or injury
may result if the product falls.
6. Do not cover slots and openings on the
product. They are provided for
ventilation and protection against
overheating. Never place the product
near radiators, or in a place where
proper ventilation is not provided.
7. Use only the power source marked on
the product. If you are not sure of the
type of power supplied to your home,
consult your dealer or local power
company.
A. When the power cord is damaged
or frayed.
B. If liquid has been spilled into the
product.
C. If the product has been exposed to
rain or water.
D. If the product does not work
normally by following the operating
instructions. Adjust only controls
covered by the operating
instructions. Improper adjustment
may require extensive work by an
authorized service center.
E. If the product has been dropped or
physically damaged.
F. If the product exhibits a distinct
change in performance.
13. During thunderstorms, avoid using
telephones except cordless types.
There may be a remote risk of an
electric shock from lightning.
14. Do not use the product to report a gas
leak, when in the vicinity of the leak.
8. Do not place objects on the power
cord. Install the product where no one
can step or trip on the cord.
9. Do not overload power outlets and
extension cords. This can result in the
risk of fire or electric shock.
10. Never push any objects through slots
in the product. This may result in the
SAVE THESE
INSTRUCTIONS
8
Introduction
L Charge the battery(ies) provided, or
CAUTION:
identified for use with the product only, in
accordance with the instructions and
limitations specified in this manual.
Installation
L Never install telephone wiring during a
lightning storm.
L Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
WARNING:
L To prevent the risk of fire or electrical
shock, do not expose the product to rain
or any type of moisture.
L Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
L Unplug the product from power outlets if
it emits smoke, an abnormal smell, or
makes an unusual noise. These
conditions can cause fire or electric
shock. Confirm that smoke has stopped
emitting and contact the Panasonic Call
Center at 1-800-211-PANA (1-800-211-
7262).
L Use caution when installing or modifying
telephone lines.
L Do not touch the plug with wet hands.
L The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
Medical
L Consult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
Battery
To reduce the risk of fire or injury to
persons, read and follow these
instructions.
determine if they are adequately
shielded from external RF (radio
frequency) energy. (The product
L Use only the battery(ies) specified.
L Do not dispose of the battery(ies) in a
fire. They may explode. Check with local
waste management codes for special
disposal instructions.
operates in the frequency range of 5.76
GHz to 5.84 GHz, and the power output
is 200 mW (max.).) Do not use the
product in health care facilities if any
regulations posted in the area instruct
you not to do so. Hospitals or health care
facilities may be using equipment that
could be sensitive to external RF energy.
L Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and
may cause burns or injury to the eyes or
skin. The electrolyte may be toxic if
swallowed.
L Exercise care when handling the
battery(ies). Do not allow conductive
materials such as rings, bracelets or
keys to touch the battery(ies), otherwise
a short circuit may cause the battery(ies)
and/or the conductive material to
overheat and cause burns.
9
Introduction
L The product should be kept away from
heat sources such as heaters, kitchen
stoves, etc. It should not be placed in
rooms where the temperature is less
than 5 °C (41 °F) or greater than 40 °C
(104 °F). Damp basements should also
be avoided.
For best performance
Base unit location/avoiding noise
The base unit and other compatible
Panasonic units use radio waves to
communicate with each other.
For maximum distance and noise-free
operation, we recommend the following:
L The maximum calling distance may be
shortened when the product is used in
the following places: Near obstacles
such as hills, tunnels, underground, near
metal objects such as wire fences, etc.
L Placing the product away from electrical
appliances.
L Placing the base unit in a HIGH and
CENTRAL location with no obstructions
such as walls.
L Operating near 5.8 GHz electrical
appliances may cause interference.
Move away from the electrical
appliances.
L Raising the antennas vertically.
L If you use the handset near a microwave
oven which is being used, noise may be
heard. Move away from the microwave
oven and closer to the base unit.
Routine care
L Wipe the outer surface of the product
with a soft moist cloth. Do not use
benzine, thinner, or any abrasive
powder.
L If you use the handset near another
cordless phone’s base unit, noise may
be heard. Move away from the other
cordless phone’s base unit and closer to
your base unit.
Environment
L Keep the product away from electrical
noise generating devices, such as
fluorescent lamps and motors.
L The product should be kept free from
excessive smoke, dust, high
temperature, and vibration.
L The product should not be exposed to
direct sunlight.
L Do not place heavy objects on top of the
product.
L When you leave the product unused for
a long period of time, unplug the product
from the power outlet.
10
Preparation
standard telephone to the same
telephone line or to the same telephone
jack using a Panasonic T-adaptor (page
7). Emergency power can be supplied to
the unit by connecting a Panasonic
battery back-up power supply noted on
page 7.
Setting up the base unit
Connecting the AC adaptor and
telephone line cord
Connect the telephone line cord until it
clicks into the base unit (A) and telephone
line jack (B). Connect the AC adaptor cord
by pressing the plug firmly (C).
If you subscribe to a DSL service
Please attach a noise filter (contact your
DSL provider) to the telephone line
between the base unit and the telephone
line jack in the event of the following:
L Use only the included Panasonic AC
adaptor PQLV1 or PQLV256.
– Noise is heard during conversations.
C
– Caller ID features (page 28) do not
function properly.
Hook
A
(120 V AC,
60 Hz)
To single-line
telephone
jack (RJ11C)
To single-line
telephone jack
(RJ11C)
B
Noise filter
Note:
L The AC adaptor must remain connected
at all times. (It is normal for the adaptor
to feel warm during use.)
L The AC adaptor should be connected to
a vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to
a ceiling-mounted AC outlet, as the
weight of the adaptor may cause it to
become disconnected.
L The unit will not work during a power
failure. We recommend connecting a
11
Preparation
Battery installation/replacement
Setting up the handset
1 Press the notch of the handset cover
firmly, and slide it in the direction of the
arrow.
Connecting the charger
Available model:
KX-TG5672/KX-TG5673
L If necessary, remove the old battery.
L Use only the included Panasonic AC
adaptor KX-TCA1 or PQLV256.
(120 V AC, 60 Hz)
2 Insert the battery (A), and press it
down until it snaps into position (B).
Then close the handset cover.
B
A
Bottom of the charger
Hooks
Fasten the AC adaptor cord to prevent
it from being disconnected.
Important:
L Use only the rechargeable Panasonic
battery noted on page 7.
12
Preparation
Attention:
Charger:
Available model:
KX-TG5672/KX-TG5673
A nickel metal hydride battery that is
recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY (1-800-
822-8837) for information on how to
recycle this battery.
Charge
contacts
Battery charge
Note:
Place the handset on the base unit or
charger for 7 hours before initial use.
While charging, “Charging” is displayed
and the CHARGE indicator on the base
unit lights. When the battery is fully
charged, “Charge completed” is
displayed.
L If you want to use the unit immediately,
charge the battery for at least 15
minutes.
L To ensure that the battery charges
properly, clean the charge contacts of
the handset, base unit, and charger with
a soft, dry cloth once a month. Clean
more often if the unit is subject to the
exposure of grease, dust, or high
humidity.
Base unit:
OR
13
Preparation
Battery level
Panasonic battery performance
Battery icon
5
Battery level
Fully charged
Medium
Operation
Operating time
While in use
(talking)
Up to 5 hours
Up to 11 days
Up to 3 hours
6
While not in use
(standby)
7
Low
Flashing: needs to be
recharged.
While using the
clarity booster
feature (page 22)
8
Empty
Note:
Note:
L When the battery needs to be charged,
the handset beeps intermittently while it
is in use.
L Battery operating time may be
shortened over time depending on
usage conditions and surrounding
temperature.
L Battery power is consumed whenever
the handset is off the base unit or
charger, even when the handset is not in
use. Hence the longer you leave the
handset off the base unit or charger, the
less time you may actually talk using the
handset.
L After the handset is fully charged,
displaying “Charge completed”, it
may be left on the base unit (or charger)
without any ill effect on the battery.
L The battery level may not be displayed
correctly after you replace the battery. In
this case, place the handset on the base
unit (or charger) and let charge for 7
hours.
14
Preparation
Controls
Base unit
A
B C
D
E
K
L
K
F G H I J
M
N O P Q R S T U V W
X
Y Z
A Display
N {PROGRAM} {AUTO}
O {MUTE}
B {ERASE}
C {ANSWER ON}
P {CALL WAIT} {FLASH}
Q {REDIAL} {PAUSE}
R CHARGE indicator
S IN USE indicator
ANSWER ON indicator
D Navigator key ({^} {V} {<} {>})
E {MEMO}
F MESSAGE indicator
G {MESSAGE}
H {STOP}
T {*} (TONE)
U MIC (Microphone)
V {1} {2} {3} (extension number)
I {GREETING REC} (Recording)
J {GREETING CHECK}
K Antenna
W {SP-PHONE} (Speakerphone)
SP-PHONE indicator
X {HOLD}
L Speaker
Y {CONF} (Conference)
M Charge contacts
Z {INTERCOM} {TRANSFER}
INTERCOM indicator
15
Preparation
N {MENU}
O {OFF}
Handset
P {PAUSE} {REDIAL}
Q {HOLD} {INTERCOM}
K
L
Note:
L Some operations not mentioned above
are displayed as soft key selections
during operation (page 17).
A
B
Example: {Mute}
M
N
Using the navigator key
C
D
The handset navigator key can be used to
navigate through menus and to select
items shown on the display, by pressing
{^}, {V}, {<}, or {>}.
B
O
P
E
F
Adjusting audio volume
Press {^} or {V} repeatedly while talking.
G
Q
{^}
H
I
{<}
{>}
J
{V}
A Speaker
B Soft keys
C Headset jack
D {C} (TALK)
E Navigator key ({^} {V} {<} {>})
F {s} (SP-PHONE)
G {*} (TONE)
H {FLASH} {CALL WAIT}
I Microphone
J Charge contacts
K Ringer indicator
Message indicator
L Receiver
M Display
16
Preparation
Handset soft keys
Displays
The handset features 2 soft keys. By
pressing a soft key, you can select the
feature shown directly above it on the
display.
Base unit display items
{Select}, {Save}, {OK} and additional
other functions are assigned to soft keys,
pay attention to soft keys to find functions
you need during handset operation.
Displayed Meaning
item
E
Flashes when message
memory is full.
E
Flashes when the date and
time need to be set.
5
Rcvd
calls
Phone
book
Base unit ringer is off.
K
L
O
E
Greeting or memo
message recording error
9@
Answering system is in
greeting only mode (caller
messages are not
recorded).
Note:
L In these operating instructions, soft key
names are written inside brackets, the
same way as other unit keys.
Example:
Unit keys: {C}, {OFF}, etc.
Soft keys: {Rcvd calls}, {Phonebook},
etc.
H1
P
Handsetnumber;displayed
when paging, being paged,
or registering .
*1
Base unit is in
programming mode.
*1 KX-TG5672/KX-TG5673
Handset display items
Displayed Meaning
item
J
5
Voice enhancer is on.
Battery level
17
Preparation
3 Enter the current hour and minute (12-
hour clock format) by selecting 2 digits
for each.
Setting the unit before
use
Example: 9:30
{0}{9} {3}{0}
Display language
The default setting is “English”.
4 Press {AM/PM} to select “AM” or “PM”.
i {Save} i {OFF}
1 {MENU} i {0}{8}
Note:
L If you make a mistake when entering the
date and time, press {<}, {>}, {^}, or
{V} to move the cursor, then make the
correction.
2 Select the desired setting.
3 Press the right soft key to save. i
{OFF}
Dialing mode
If you cannot make calls, change this
setting depending on your telephone line
service. The default setting is “Tone”.
“Tone”: For tone dial service.
“Pulse”: For rotary pulse dial service.
1 {MENU} i {0}{5}{1}
2 Select the desired setting. i {Save}
i {OFF}
Date and time
Set the correct date and time. When you
play back a message from the answering
system (page 37), the unit announces the
day and time it was recorded.
1 {MENU} i {4}
2 Enter the current month, day, and year
by selecting 2 digits for each.
Example: August 15, 2006
{0}{8} {1}{5} {0}{6}
18
Making/Answering Calls
Making a call using the redial list
The last 5 phone numbers dialed are
stored in the redial list.
Making calls
Using the handset
1 {REDIAL}
1 Lift the handset and dial the phone
2 Press {^} or {V} to select the desired
number.
number.
L To correct a digit, press {Clear}.
3 {C}
2 Press {C} or {Call}.
Erasing a number in the redial list
3 When you finish talking, press {OFF} or
place the handset on the base unit or
charger.
1 {REDIAL}
2 Press {^} or {V} to select the desired
number. i {Erase} i {Yes} i
{OFF}
Note:
L “Line in use” is displayed when
someone is talking on another handset
(KX-TG5672/KX-TG5673) or another
phone.
PAUSE button (for PBX/long distance
service users)
A pause is sometimes required when
making calls using a PBX or long distance
service.
For example, if you need to dial the line
access number “9” when making outside
calls with a PBX:
Using the speakerphone
1 Lift the handset, dial the phone number,
and press {s}.
L Speak alternately with the other party.
2 When you finish talking, press {OFF}.
Note:
1 {9} i {PAUSE} i Dial the phone
number.
L Use the speakerphone in a quiet
environment.
2 {C}
Note:
L To switch to the receiver, press {C}.
L A 3.5 second pause is inserted each
time {PAUSE} is pressed. Press
repeatedly to insert longer pauses.
Adjusting the receiver/speaker volume
Press {^} or {V} repeatedly while talking.
19
Making/Answering Calls
Using the base unit
Answering calls
1 {SP-PHONE}
When a call is being received, the ringer
indicator on the handset and IN USE
indicator on the base unit flash rapidly.
2 Dial the phone number.
3 When the other party answers, speak
into the MIC.
Using the handset
L Speak alternately with the other party.
1 Lift the handset and press {C} or {s}.
4 When you finish talking, press {SP-
L You can also answer the call by
pressing any button except {^}, {V},
{<}, {>}, or {OFF}. (Any key talk
feature)
PHONE}.
Note:
L Use the speakerphone in a quiet
environment.
2 When you finish talking, press {OFF}.
L While on a call, you can switch from the
base unit to the handset:
Note:
– Press {C} on the handset, then
press {SP-PHONE} on the base unit.
– If the handset is on the base unit,
simply lift it.
L You can change the ringer indicator light
color and the ringer tone. You can also
adjust the handset ringer volume (page
34).
Adjusting the speaker volume
Auto talk
Press {^} or {V} repeatedly while talking.
This feature allows you to answer a call by
simply lifting the handset off the base unit
or charger. You do not need to press {C}.
To activate this feature, see page 34.
Redialing the last number dialed
{SP-PHONE} i {REDIAL}
Temporary ringer off
While the handset is ringing for an outside
call, you can turn the ringer off temporarily
by pressing {OFF}.
20
Making/Answering Calls
Using the base unit
Useful features during a
call
1 {SP-PHONE}
2 Speak into the MIC.
HOLD button
3 When you finish talking, press {SP-
This feature allows you to put an outside
call on hold.
PHONE}.
Handset
Adjusting the ringer volume
Press {^} or {V} repeatedly to select the
desired volume when in standby mode.
1 Press {HOLD} during an outside call.
L To transfer the call to another
extension, continue from step 2 on
page 44, “Transferring calls,
conference calls”.
L To turn the ringer off, press and hold {V}
until the unit beeps 2 times.
Setting the ringer tone
There are 3 tones.
2 Press {HOLD} again.
L To release the hold, press {C}.
1 Press {^} or {V}.
L The base unit user can take the call
by pressing {SP-PHONE}.
L Another handset user can take the
2 Within 10 seconds, press {<} or {>}
repeatedly to select the desired tone.
call by pressing {C}.
Base unit
Press {HOLD} during an outside call.
L To release the hold, press {SP-
PHONE}.
L Handset users can take the call by
pressing {C}.
Note for handset and base unit:
L If another phone is connected on the
same line (page 11), you can also take
the call by lifting its handset.
L If a call is kept on hold for more than 6
minutes, an alarm tone starts to sound.
After 4 additional minutes on hold, the
call is disconnected.
21
Making/Answering Calls
Press {CALL WAIT} to answer the 2nd
call.
Mute
While mute is turned on, you can hear the
other party, but the other party cannot hear
you.
L To switch between calls, press {CALL
WAIT}.
Temporary tone dialing (for rotary/
pulse service users)
You can temporarily switch the dialing
mode to tone when you need to access
touch tone services (for example,
answering services, telephone banking
services, etc.).
Handset
To mute your voice, press {Mute}.
L To return to the conversation, press
{Mute} or {C}.
Note:
L {Mute} is a soft key visible on the
handset display during a call.
Press {*} (TONE) before entering access
numbers which require tone dialing.
Base unit
Handset clarity booster
To mute your voice, press {MUTE}.
L To return to the conversation, press
{MUTE} or {SP-PHONE}.
This feature can improve sound clarity
when the handset is used in an area where
there may be interference. During an
outside call, this feature is turned on
automatically when necessary. You can
also turn this feature on or off manually.
FLASH button
Pressing {FLASH} allows you to use
special features of your host PBX such as
transferring an extension call, or accessing
optional telephone services such as Call
Waiting.
1 Press {MENU} during an outside call.
2 Press {2} to select “Booster on” or
“Booster off”.
Note:
Note:
L To change the flash time, see page 35.
L When this feature is turned off manually
during a call, it does not turn on
For Call Waiting service users
To use Call Waiting, you must subscribe to
your telephone company’s Call Waiting
service.
automatically during the same call.
L While this feature is turned on;
– the battery operating time is
shortened (page 14).
This feature allows you to receive calls
while you are already talking on the phone.
If you receive a call while on the phone,
you will hear a Call Waiting tone. Please
contact your telephone company for
details and availability of this service in
your area.
– the maximum number of extensions
that can be used at a time may
decrease when you have 3 handsets.
22
Making/Answering Calls
Note:
Handset voice enhancer
L This feature turns off if another handset
starts to have an intercom call with the
base unit (KX-TG5672/KX-TG5673), or
another unit starts to use the answering
system.
This feature clarifies the voice of the
person you are talking to, reproducing a
more natural-sounding voice that is easier
to hear and understand (page 35).
1 Press {MENU} during an outside call.
L This feature turns off after you hang up
the call.
2 Press {3} to select “V.E. on” or “V.E.
L The speed may become close to normal
when the handset receives constant
incoming audio for a period of time.
off”.
L When this feature is turned on, J
is displayed.
Call share
Note:
This feature allows the handset and base
unit to join an existing outside call.
L Depending on the condition and quality
of your telephone line, this feature may
emphasize existing line noise. If it
becomes difficult to hear, turn this
feature off.
Handset
To join the conversation, press {C} when
the other extension is on an outside call.
Handset Slow Talk
Base unit
This feature works to help slow down the
incoming audio when two parties are
having a two way conversation.
To join the conversation, press {SP-
PHONE} when the handset is on an
outside call.
Important:
Note for handset and base unit:
L You cannot use this feature when;
– you are on a conference call,
– you are listening to messages in the
answering system,
– another unit is using the answering
system, or
L A maximum of 4 parties (including 1
outside party) can join a conversation
using 3 extensions (KX-TG5672/KX-
TG5673).
– another handset is having an intercom
call with the base unit (KX-TG5672/
KX-TG5673).
Press {Slow} during an outside call.
L “Slow” starts blinking.
L To turn this feature off, press {Slow}
again. “Slow” stops blinking.
23
Phonebook
Key
{0}
Character
Handset phonebook
0
Space
{*}
{#}
;
#
You can add up to 50 items to the handset
phonebook and search for phonebook
items by name.
L To enter another character that is
located on the same dial key, first press
{>} to move the cursor to the next
space.
Adding items to the phonebook
1 {Phonebook}
2 {Add}
Editing/correcting a mistake
Press {<} or {>} to move the cursor to the
character or number you want to erase,
then press {Clear}. Enter the appropriate
character or number.
3 Enter the name (max. 16 characters).
i {Next}
4 Enter the phone number (max. 32
L Press and hold {Clear} to erase all
characters or numbers.
digits). i {Next}i {Save}
L To add other items, repeat from step
2.
Finding and calling a
phonebook item
5 {OFF}
Note:
Phonebook items can be searched for
alphabetically by scrolling through the
phonebook items or by entering the first
initial.
L Caller ID subscribers can use ringer ID
and light-up ID features (page 29).
Character table
Searching for a name alphabetically by
scrolling through all items
Key
{1}
{2}
{3}
{4}
{5}
{6}
{7}
{8}
{9}
Character
& ’
(
)
,
–
.
/
1
1 {Phonebook} i {Search}
a
d
g
j
b
c
f
A B C 2
D E F 3
2 Press {^} or {V} to select the desired
e
h
k
item.
i
G H I
K L
4
5
3 Press {C} to dial the phone number.
l
J
m n
o
r
M N O 6
P Q R S 7
T U V 8
W X Y Z 9
p
t
q
u
s
v
y
w x
z
24
Phonebook
Searching for a name by initial
Chain dial
This feature allows you to dial phone
numbers in the handset phonebook while
you are on a call. This feature can be used,
for example, to dial a calling card access
number or bank account PIN that you have
stored in the handset phonebook, without
having to dial manually.
1 {Phonebook} i {Search}
2 Press the dialing button ({0} to {9},
{#}, or {*}) that corresponds to the
first letter you are searching for (see the
character table, page 24).
Example: “LISA”
Press {5} repeatedly to display the first
phonebook entry starting with the initial
“L” and go to step 3.
1 During an outside call, press {MENU}.
2 “Phonebook” i {Select}
L If there is no item corresponding to
the letter you selected, the next item
is displayed.
3 Find the desired item (page 24, 25). i
{Call}
Note:
3 Press {V} to select the desired item.
L When storing a calling card access
number and your PIN in the phonebook
as one phonebook item, press {PAUSE}
to add pauses after the number and PIN
as necessary (page 19).
4 Press {C} to dial the phone number.
Editing items in the phonebook
1 Find the desired item (page 24, 25). i
L If you have rotary or pulse service, you
need to press {*} before pressing
{MENU} in step 1 to change the dialing
mode temporarily to tone.
{Option} i “Edit” i {Select}
2 Edit the name if necessary (see the
character table, page 24). i {Next}
3 Edit the phone number if necessary.
i {Next} i {Save} i {OFF}
Erasing items in the phonebook
1 Find the desired item (page 24, 25).
2 {Erase} i {Yes} i {OFF}
25
Phonebook
Copying handset
phonebook items
Available model:
KX-TG5672/KX-TG5673
You can copy one or all of the phonebook
items from one handset to another.
Important:
L Ringer ID and light-up ID settings for
phonebook items are not copied.
Copying an item
1 {MENU} i {#}{1}
2 Select the destination unit by pressing
{^} or {V}. i {Next}
3 Find the desired item (page 24, 25). i
{Send}
4 Press {OFF} after the long beep.
Copying all items
1 {MENU} i {#}{2}
2 Select the destination unit by pressing
{^} or {V}. i {Send}
3 Press {OFF} after the long beep.
26
Base Unit Speed Dialer
For example, if you need to dial the line
access number “9” when making outside
calls with a PBX:
Base unit speed dialer
In step 2, press {9}, {PAUSE}, then enter
the phone number.
You can assign one phone number to each
of the 10 dial keys ({0} – {9}) on the base
unit.
Note:
L A 3.5 second pause is inserted each
time {PAUSE} is pressed. Press
repeatedly to insert longer pauses. “P”
Adding phone numbers to the
speed dialer
is displayed when {PAUSE} is pressed.
L When {*} is pressed, “$” is displayed.
When {#} is pressed, “#” is displayed.
Important:
L Before storing phone numbers, make
sure the base unit is not being used.
To erase a stored phone number
1 Press {PROGRAM} 2 times.
1 {PROGRAM}
2 Enter the phone number (max. 32
digits).
2 Press the desired dial key ({0} – {9}).
L If a pause is required for dialing,
press {PAUSE} where needed.
L If you misdial, press {STOP} and
repeat from step 1.
Calling someone with the speed
dialer
1 {SP-PHONE} i {AUTO}
2 Press the desired dial key ({0} – {9}).
Note:
3 {PROGRAM}
4 Press a dial key ({0} – {9}).
Note:
L Speed dial numbers stored in the base
unit can only be dialed from the base
unit.
L If a phone number is stored in a dial key
which already contains a phone number,
the old number will be erased.
L We recommend you make a note of
which phone numbers are stored in
which dial keys.
PAUSE button (for PBX/long distance
service users)
A pause is sometimes required when
making calls using a PBX or long distance
service.
27
Caller ID Service
Call Waiting Caller ID display
Using Caller ID service
If you subscribe to both Caller ID and Call
Waiting with Caller ID services, the 2nd
caller’s information is displayed after you
hear a Call Waiting tone (page 22). Please
contact your telephone company for
details and availability of this service in
your area.
This unit is Caller ID compatible. To use
Caller ID features, you must subscribe to
your telephone company’s Caller ID
service.
Caller ID features
When an outside call is being received, the
calling party’s name and telephone
number are displayed.
Caller information for the last 50 different
callers is logged in the caller list by the
most recent call to the oldest.
Talking Caller ID
This feature lets you know who is calling
without looking at the display. When a call
comes in, the handset and base unit
announces the caller’s name displayed on
the handset following every ring.
To use this feature, you must subscribe to
your telephone company’s Caller ID
service.
L Generally caller information is displayed
from the 2nd ring.
L If the unit cannot receive caller
information, the following is displayed:
– “Out of area”: The caller dialed
from an area which does not provide
Caller ID service.
L Name pronunciation may vary. This
feature may not pronounce all names
correctly.
L Caller ID supports names of up to 15
letters. If the caller’s name has more
than 15 letters, the name is not
– “Private caller”: The caller
requested not to send caller
information.
– “Long distance”: The caller called
you long distance.
displayed or announced correctly.
L Usually the unit announces the caller’s
name after the 2nd ring. If you turn on
the answering system and set the ring
count to “2” (page 41), the unit does not
announce the caller’s name. If “Toll
saver” is selected and there is a new
message, the unit does not announce
the caller’s name.
L If the unit is connected to a PBX system,
caller information may not be received
properly. Consult your PBX supplier.
Missed calls
If a call is not answered, the unit treats the
call as a missed call. The number of
missed calls is shown on the handset
display. This lets you know if you should
view the caller list to see who called while
you were out.
L When you receive a call while on the
phone, the 2nd caller’s name is not
announced even if you subscribe to both
Caller ID and Call Waiting with Caller ID
services.
L The number of missed calls can also be
shown on the multiple handsets (KX-
TG5672/KX-TG5673, page 30).
L This feature can be turned on or off
(page 35).
28
Caller ID Service
Ringer ID
Light-up ID
This feature can help you identify who is
calling by using different ringers for
different callers stored in the phonebook.
You can assign a different ringer to each
phonebook item. When a call is received
from a caller stored in the phonebook, the
ringer is used after Caller ID information is
displayed.
If you select “No Ringer ID”, the
handset uses the ringer tone you selected
on page 34 when a call is received from
that caller. The default setting is “No
Ringer ID”.
This feature can help you identify who is
calling by using different ringer indicator
colors for different callers stored in the
handset phonebook. You can assign a
different indicator color to each handset
phonebook item. When a call is received
from a caller stored in the handset
phonebook, the indicator color is used
after Caller ID information is displayed.
If you select “No Light-up ID”, the
handset uses the ringer indicator color you
selected on page 34 when a call is
received from that caller.
The default setting is “No Light-up ID”.
1 Find the desired item (page 24, 25). i
{Option}
1 Find the desired item (page 24, 25). i
{Option}
2 “Ringer ID” i {Select}
3 Select the desired ringer tone.
4 {Save} i {OFF}
2 “Light-up ID” i {Select}
3 Select the desired ringer indicator color.
4 {Save} i {OFF}
29
Caller ID Service
3 Press {Edit} repeatedly until the phone
number is shown in the desired format.
1 Local phone number
Caller list
Example:
321-5555
Viewing the caller list and calling back
2 Area code – Local phone number
1 Press {^} or {V} to enter the caller list.
Example:
555-321-5555
2 Press {V} to search from the most
recent call, or {^} to search from the
oldest call.
3 1 – Area code – Local phone
number
Example:
1-555-321-5555
3 {C}
4 {C}
Note:
L KX-TG5672/KX-TG5673:
Caller ID number auto edit feature
Once you call back an edited number, the
unit can automatically edit other incoming
phone numbers each time you receive a
call.
Each handset has its own caller list. If
you viewed the caller list or answered a
call on one handset, the same
information in the other handsets is
displayed as “missed calls”.
For example, you can use this feature to
set the unit to ignore the area code of
callers in your area code, so that you can
call these local numbers using caller
information without dialing the area code.
To activate this feature, you must edit an
item in the caller list, then call that number.
After that, phone numbers from that
caller’s area code are edited automatically.
This feature can be turned on or off (page
34).
L You can also press {Rcvd calls} to
enter the caller list.
L If the same caller calls more than once, it
is displayed with the number of times the
caller called (“×2” to “×9”). Only the date
and time of the most recent call is
stored.
L A Q is displayed next to items which
have already been viewed or answered.
Editing a caller’s phone number before
calling back
Note:
L Phone numbers from the 4 most recently
edited area codes are automatically
edited.
You can edit a phone number in the caller
list by removing its area code and/or the
long distance code “1”.
L If you move to another area, you can
turn this feature off to erase previously
edited area codes. To use this feature
again, turn it on and reprogram the area
codes you want to edit once again.
1 Press {^} or {V} to enter the caller list.
2 Select the desired item. i {Select}
30
Caller ID Service
Storing caller information into the
phonebook
1 Press {^} or {V} to enter the caller list.
2 Select the desired item. i {Select}
L To edit the number, press {Edit}
repeatedly until the phone number is
shown in the desired format.
3 {Save}
L If there is the name information for
the caller, skip to step 5.
4 Enter the name (see the character
table, page 24). i {Next} i {Save}
5 {OFF}
Erasing selected caller information
1 Press {^} or {V} to enter the caller list.
2 Select the desired item.
3 {Erase} i {Yes} i {OFF}
Erasing all caller information
1 Press {^} or {V} to enter the caller list.
2 {All erase} i {Yes}
31
Programming
Programmable settings
You can customize the unit by programming the following features using the handset. To
access the features, there are 2 methods: scrolling through the display menus (page 32)
or using the direct commands (page 33).
L Mainly the direct command method is used in these operating instructions.
Programming by scrolling through the display menus
1 {MENU}
2 Press {^} or {V} to select the desired menu. i {Select}
L If there are sub-menu(s), press {^} or {V} to select the desired item. i {Select}
Example: To access the handset ringer tone setting
Press {^} or {V} to select “Ringer setting”. i {Select}
Then press {^} or {V} to select “Ringer tone”. i {Select}
3 Press {^} or {V} to select the desired setting.
L This step may vary depending on the feature being programmed.
4 {Save} i {OFF}
Main menu
Sub-menu 1
Sub-menu 2
Page
Message play
Ringer setting
–
–
–
–
–
–
–
–
–
–
–
page 38
Ringer volume
–
Ringer tone
–
–
Ring color
*1
Date and time
–
page 18
–
Voice enhancer
–
*2
Copy phonebook
Copy 1 item
page 26
page 26
–
Copy all items
Talking CallerID
Customer support
–
–
page 35
32
Programming
Main menu
Sub-menu 1
Sub-menu 2
Page
*1
Initial setting
Set answering
Ring count
page 41
*1
Recording time
page 42
*1
Remote code
page 41
Message alert
LCD contrast
Key tone
–
–
–
–
–
–
page 42
–
–
Auto talk
page 20
Caller ID edit
Time adjustment
Set tel line
–
*1
–
*1
Set dial mode
page 18
*1
Set flash time
–
–
*1
Set line mode
*1
Set base unit
Registration
Talking CallerID
–
–
–
page 46
page 18
Change language
*1 If you program these settings using one of the handsets, you do not need to program
the same item using another handset (KX-TG5672/KX-TG5673).
*2 KX-TG5672/KX-TG5673
Programming using the direct commands
1 {MENU}
Note:
L In the following table:
2 Enter the desired feature code.
– < > shows the default setting.
– If “System setting” column is checked,
you do not need to program the same
item using another handset (KX-
TG5672/KX-TG5673).
3 Enter the desired setting code.
L This step may vary depending on the
feature being programmed.
4 {Save} i {OFF}
L If you make a mistake or enter the wrong
code, press {OFF}, then start again by
pressing {MENU}.
33
Programming
Feature
Feature
code
Setting code
System
setting
*1
Auto talk
{0}{3}
{1}: On{0}: <Off>
–
–
Caller ID edit
{0}{4}
{1}: <On> {0}: Off
(Caller ID number auto edit)
(page 30)
Change language
{0}{8}
{1}: <English>
–
(Display language)
{2}: Español(page 18)
*2
Copy phonebook(1 item)
Copy phonebook(all items)
Date and time
{#}{1}
{#}{2}
{4}
(page 26)
–
–
*2
(page 26)
(page 18)
r
–
*3
Key tone
{0}{2}
{0}{1}
{1}: <On> {0}: Off
{1}–{6}: Level 1–6 <3>
LCD contrast
–
(Display contrast)
Message alert
Message play
Recording time
{0}{#}
{2}
{1}: On{0}: <Off>
–
–
–
{0}{6}{2}
{1}: 1min{2}: 2min
{3}: <3min>
r
{0}: Greeting only
Registration
Remote code
{0}{0}
(page 46)
(page 41)
–
r
–
{0}{6}{3}
{1}{4}
Ring color
(Ringer indicator color)
{1}: <Color1>=Amber
{2}: Color2=Green
{3}: Color3=Red
{4}: Multicolor
Ring count
{0}{6}{1}
{1}{2}
{2}–{7}: 2–7rings <4>
{0}: Toll saver
r
–
*4
Ringer tone(Handset)
{1}–{3}: Tone<1>–3
{4}–{7}: Melody 1–4
Ringer volume(Handset)
{1}{1}
{1}: Low {2}: Medium
–
{3}: <High> {0}: off
Set dial mode
{0}{5}{1}
{1}: Pulse
r
{2}: <Tone> (page 18)
34
Programming
Feature
Feature
code
Setting code
System
setting
*5
Set flash time
{0}{5}{2}
{1}: <700ms> {2}: 600ms
{3}: 400ms{4}: 300ms
{5}: 250ms{6}: 110ms
{7}: 100ms{8}: 90ms
r
*6
Set line mode
{0}{5}{3}
{1}: A{2}: <B>
r
Talking CallerID
{9}
{1}: <On> {0}: Off
–
(Handset)
(page 28)
Talking CallerID
(Base unit)
{0}{*}{4} {1}: <On> {0}: Off
–
r
–
(page 28)
*7
Time adjustment
{0}{9}
{1}: <Caller ID[auto]>
{0}: Manual
(Caller ID subscribers only)
Voice enhancer
{5}
{1}: On{0}: <Off>
*1 If you subscribe to Caller ID service and want to view the caller’s information after lifting
up the handset to answer a call, turn off this feature.
*2 KX-TG5672/KX-TG5673
*3 You can select whether or not key tones are heard when keys are pressed. Includes
confirmation tones and error tones.
*4 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone
(tone 1 to 3). If you select a melody, you cannot distinguish lines by their ringers.
*5 The flash time depends on your telephone exchange or host PBX. Consult your PBX
supplier if necessary. The setting should stay at “700ms” unless pressing {FLASH}
fails to pick up the call waiting call.
*6 Generally, the line mode setting should not be adjusted. If “Line in use” is not
displayed when another phone connected to the same line is in use, you need to
change the line mode to “A”.
*7 This feature allows the unit to automatically adjust the date and time setting when caller
information is received. To use this feature, set the date and time first.
Customer support
The handset can display the Internet address where you can download operating
instructions or get further information for this product using your computer.
{MENU} i “Customer support” i {Select} i {OFF}
35
Answering System
Screening calls
Answering system
While a caller is leaving a message, you
can listen to the call through the base unit’s
speaker. To adjust the speaker volume,
press {^} or {V} repeatedly.
You can answer the call by pressing {SP-
PHONE} on the base unit, or by pressing
{C} on the handset.
Important:
L Only 1 person can access the answering
system at a time.
L When callers leave messages, the unit
records the day and time of each
message. Make sure the date and time
have been set (page 18).
Turning off the call screening feature
When the base unit is not in use, press
{GREETING CHECK}, then press {V}
repeatedly until “0” is displayed.
OR
Memory capacity
The total recording capacity (including
your greeting message, caller messages,
and voice memo) is about 21 minutes.
A maximum of 64 messages (including a
greeting message) can be recorded.
While screening, press {V} repeatedly until
“0” is displayed.
Note:
L If the message memory becomes full,
the ANSWER ON indicator flashes
rapidly (if the answering system is
turned on). Erase unnecessary
messages (page 37).
L If you adjust the speaker volume while
listening to messages or talking on the
intercom, the speaker volume for call
screening is turned on again.
L If less than 3 minutes of recording time is
available, the unit announces the
remaining recording time when
operating the answering system. Erase
unnecessary messages (page 37).
Recording your greeting
message
You can record your own greeting
message (max. 2 minutes) that is played
when the answering system answers a
call. If you do not record a greeting
message, a prerecorded greeting
message is used.
Turning the answering system
on/off
Press {ANSWER ON} to turn on/off the
answering system.
1 {GREETING REC}
L When the answering system is turned
on, the ANSWER ON indicator lights.
2 Within 10 seconds, press {GREETING
REC} again.
L When the answering system is turned
off, the ANSWER ON indicator turns off.
3 After the base unit beeps, speak clearly
about 20 cm (8 inches) away from the
MIC.
36
Answering System
4 To stop recording, press {STOP}.
Listening to messages
using the base unit
Playing back the greeting message
Press {GREETING CHECK}.
When new messages have been
recorded, the MESSAGE indicator on the
base unit flashes.
Press {MESSAGE}.
L The unit plays new messages.
Erasing your greeting message
Press {GREETING CHECK}, and then
press {ERASE} while your greeting
message is playing.
L When you have no new messages, the
unit plays back all messages.
Prerecorded greeting message
If you erase or do not record your own
greeting message, the unit plays a
prerecorded greeting message for callers
and ask them to leave messages. If the
message recording time (page 42) is set to
“Greeting only”, caller messages are
not recorded and the unit plays a different
prerecorded greeting message asking
callers to call again.
Adjusting the speaker volume
Press {^} or {V} repeatedly while listening
to a message.
Repeating a message
Press {<} during playback.
L If pressed within the first 5 seconds of a
message, the previous message is
played.
Skipping a message
Press {>} during playback.
Pausing a message
Press {STOP} during playback.
L To resume playback, press
{MESSAGE}.
L To stop playback completely, press
{STOP} again.
Erasing a message
Press {ERASE} during playback.
Erasing all messages
Press {ERASE} 2 times while the unit is
not being used.
37
Answering System
Calling back (Caller ID subscribers
only)
If Caller ID information was received for
the call, you can call the caller back while
listening to the message.
Listening to messages
using the handset
When new messages have been
recorded:
1 Press {Select} during playback.
– “New message” is displayed.
L To edit the number before calling
back, press {Edit} repeatedly to
select the desired format (page 30).
– The message indicator on the handset
flashes slowly if the message alert
feature is turned on (page 42).
2 {Call}
1 {MENU}
Answering system commands
You can also operate the answering
system by pressing dial keys on the
handset during playback.
2 “Message play” i {Select}
L The handset plays new messages
including memo messages.
L When you have no new messages,
the handset plays back all messages.
Key
Command
{1} or {<} Repeat message (during
3 Press {OFF} when finished.
*1
playback)
Note:
{2} or {>} Skip message (during
L You can also listen to the messages by
pressing {MENU}, then pressing {2}.
L To switch to the receiver, press {C}.
playback)
{4}
{5}
{8}
{9}
{0}
Play new messages
Play all messages
Adjusting the receiver/speaker volume
Press {^} or {V} repeatedly while listening
to a message.
Turn answering system on
*2
Stop playback
Turn answering system off
Voice guidance
{*}{4} or Erase currently playing
{Erase}
message
If you do not press any buttons after the
last message is played back, the unit’s
voice guidance starts. Operate the
answering system by following the
guidance as necessary.
{*}{5}
Erase all messages
*1 If pressed within the first 5 seconds of a
message, the previous message is
played.
*2 To resume operation, press a command
key within 15 seconds, or the voice
guidance will start.
38
Answering System
Voice memo
Remote operation
Using a touch tone phone, you can call
your phone number from outside and
access the unit to listen to messages. The
unit’s voice guidance prompts you to press
certain dial keys to perform different
operations.
Recording a voice memo
You can use the base unit to leave a voice
memo (voice message) for yourself or
someone else (max. 3 minutes). Voice
memos can be played back later with the
same operation used to play back
answering system messages.
Important:
L In order to operate the answering
system remotely, you must first set a
remote code (page 41). This code must
be entered each time you operate the
answering system remotely.
Base unit
1 {MEMO}
2 After the unit beeps, speak clearly
about 20 cm (8 inches) away from the
MIC.
Using the answering system
remotely
3 To stop recording, press {STOP}.
1 Dial your phone number from a touch
tone phone.
2 After the greeting message starts, enter
your remote code (page 41).
L The unit plays back new messages.
L After playing back new messages,
the voice guidance starts.
3 Follow the voice guidance as
necessary.
4 When finished, hang up.
Note:
L You can ignore the voice guidance and
control the unit using remote commands
(page 40).
39
Answering System
Key
Remote command
Voice guidance
During remote operation, the unit’s voice
guidance prompts you to press {1} to
perform a specific operation, or press {2}
to listen to more available operations.
Operations are presented by voice
guidance in the following order:
{*}{4}
Erase currently playing
message
{*}{5}
Erase all messages
*1 If pressed within the first 5 seconds of a
message, the previous message is
played.
*2 To resume operation, enter a remote
command within 15 seconds, or the
voice guidance starts.
– Play back all messages
– Play back new messages
– Record a message
– Erase all messages
Turning on the answering system
remotely
If the answering system is off, you can turn
it on remotely.
Note:
L If you do not press any dial keys within
10 seconds after a voice guidance
prompt, the unit disconnects your call.
L If less than 3 minutes of recording time is
available, the unit announces the
remaining recording time after the last
message is played back.
1 Dial your phone number.
2 Let the phone ring 15 times.
L The unit answers your call with the
greeting message.
Remote commands
L You can hang up, or if you call from a
touch tone phone, you can enter your
remote code and begin remote
operation (page 39).
You can press dial keys to access certain
answering system functions without
waiting for the voice guidance to prompt
you.
Skipping the greeting message to leave
a message
Key
Remote command
{1}
Repeat message (during
You can leave a message just as any
outside caller can. Call your phone
number. When the answering system
picks up, press {*} to skip the greeting
message and record your message after
the beep.
*1
playback)
{2}
Skip message (during
playback)
{4}
{5}
{9}
{0}
Play new messages
Play all messages
*2
Stop playback
Turn answering system
off
40
Answering System
For Voice Mail service subscribers
If you subscribe to a flat-rate service
package that includes Caller ID, Call
Waiting, Voice Mail, and unlimited local/
regional/long distance calls, please note
the following:
Answering system
settings
Remote code
A remote code must be entered when
operating the answering system remotely.
This code prevents unauthorized parties
from listening to your messages remotely.
The default setting is “11”.
L To use the Voice Mail service provided
by your telephone company rather than
the unit’s answering system, turn off the
answering system (page 36).
This unit does not have an indicator to
indicate if there are new messages in
your mailbox service.
1 {MENU} i {0}{6}{3}
L To use this unit’s answering system
rather than the Voice Mail service
provided by your telephone company,
please contact your telephone company
to deactivate your Voice Mail service.
If your telephone company cannot do
this:
– Set this unit’s “Ring count” setting
so that this unit’s answering system
answers calls before your telephone
company’s Voice Mail service tries to
answer your calls. It is necessary to
check the ring count required to
activate the Voice Mail service
provided by your telephone company
before changing this setting.
– Change the ring count of the Voice
Mail service so that the answering
system can answer the call first. To do
so, consult your telephone company.
2 Enter the desired 2-digit remote code.
i {Save} i {OFF}
Ring count
You can change the number of times the
phone rings before the unit answers calls.
The default setting is “4”.
“Toll saver”: The unit answers on the
2nd ring when new messages have been
recorded, and on the 4th ring when there
are no new messages. If you call your
phone from outside to listen to new
messages (page 39), you will know that
there are no new messages when the
phone rings for the 3rd time. You can then
hang up without being charged for the call.
1 {MENU} i {0}{6}{1}
2 Select the desired setting. i {Save}
i {OFF}
41
Answering System
Caller’s recording time
You can change the maximum message
recording time allotted to each caller.
The default setting is “3min”.
“Greeting only”: The unit plays the
greeting message but does not record
caller messages.
1 {MENU} i {0}{6}{2}
2 Select the desired setting. i {Save}
i {OFF}
Note:
L If the message memory becomes full,
the unit automatically switches to the
“Greeting only” mode and no new
messages are recorded. If you have
recorded your own greeting message,
that same greeting message is
announced to callers even though their
messages are not recorded. If you have
not recorded your own greeting
message, the prerecorded message
used for “Greeting only” mode is
announced to callers (page 37).
Message alert
You can select whether or not the
message indicator on the handset flashes
when new messages are recorded (page
38). The default setting is “Off”.
1 {MENU} i {0}{#}
2 Select the desired setting. i {Save}
i {OFF}
Note:
L While message alert is on, battery
operating time is shortened (page 14).
42
Multi-unit Operation
Answering an intercom call
Intercom
Handset
Intercom calls can be made:
1 Press {C} to answer the page.
2 To end the intercom call, press {OFF}.
Base unit
– between the handset and base unit
– between handsets (KX-TG5672/5673)
Note:
L If you receive a phone call while talking
on the intercom, you hear 2 tones. To
answer the call with the handset, press
{OFF}, then press {C}. To answer the
call with the base unit, press {SP-
PHONE} 2 times.
1 Press {SP-PHONE} or {INTERCOM}
to answer the page.
2 To end the intercom call, press {SP-
PHONE}.
L You can locate a misplaced handset by
Note:
paging it (handset locator).
L When the ringer volume is set to off, the
handset or the base unit rings at the low
level for intercom calls.
KX-TG5671
Making an intercom call
Handset
KX-TG5672/KX-TG5673
Making an intercom call
Handset
1 {INTERCOM}
L The base unit beeps for 1 minute.
L To stop paging, press {OFF}.
1 {INTERCOM}
2 To page the base unit, press {0}.
To page another handset, enter its
extension number ({1} – {3}).
2 To end the intercom call, press {OFF}.
Base unit
L The destination unit beeps for 1
minute.
1 {INTERCOM}
L The handset beeps for 1 minute.
L To stop paging, press {OFF}.
L To stop paging, press {SP-PHONE}
or {INTERCOM}.
3 To end the intercom call, press {OFF}.
2 To end the intercom call, press {SP-
PHONE}.
43
Multi-unit Operation
Base unit
Transferring calls,
conference calls
1 {INTERCOM}
2 Press {1}, {2}, or {3}.
Outside calls can be transferred between
the handset and base unit, and between 2
handsets. The handset and base unit, or 2
handsets can have a conference call with
an outside party.
L The destination unit beeps for 1
minute.
L To stop paging, press {SP-PHONE}
or {INTERCOM}.
3 To end the intercom call, press {SP-
Handset
PHONE}.
1 During an outside call, press
{INTERCOM} to put the call on hold.
Answering an intercom call
Handset
2 KX-TG5671
Press {base}.
1 Press {C} to answer the page.
2 To end the intercom call, press {OFF}.
Base unit
KX-TG5672/KX-TG5673
To page the base unit, press {0}.
To page another handset, enter its
extension number ({1} – {3}).
3 Wait for the paged party to answer.
1 Press {SP-PHONE} or {INTERCOM}
L If the paged party does not answer,
press {C} to return to the outside
call.
to answer the page.
2 To end the intercom call, press {SP-
PHONE}.
4 To complete the transfer, press {OFF}.
Note for handset and base unit:
L The outside call is being routed to the
L When the ringer volume is set to off, the
handset or the base unit rings at the low
level for intercom calls.
unit.
To establish a conference call, press
{Conf}.
L To leave the conference, press
{OFF}. The other parties can
continue the conversation.
L To put the outside call on hold, press
{HOLD}. To resume the conference,
press {Conf}.
44
Multi-unit Operation
4 To complete the transfer, press {SP-
Base unit
PHONE}.
L The outside call is being routed to the
handset.
To establish a conference call, press
{CONF}.
KX-TG5671
1 During an outside call, press
{INTERCOM} to put the call on hold.
L To leave the conference, press {SP-
PHONE}. The other parties can
continue the conversation.
2 Wait for the paged party to answer.
L If the paged party does not answer,
press {INTERCOM} to return to the
outside call.
L To put the outside call on hold, press
{HOLD}. To resume the conference,
press {CONF}.
3 To complete the transfer, press {SP-
PHONE}.
Answering transferred calls
L The outside call is being routed to the
handset.
To establish a conference call, press
{CONF}.
L To leave the conference, press {SP-
PHONE}. The other parties can
continue the conversation.
Handset
Press {C} to answer the page.
Base unit
Press {SP-PHONE} to answer the page.
L To put the outside call on hold, press
{HOLD}. To resume the conference,
press {CONF}.
Note for handset and base unit:
L After the paging party disconnects, you
can talk to the outside caller.
KX-TG5672/KX-TG5673
1 During an outside call, press
{INTERCOM} to put the call on hold.
2 Press {1}, {2}, or {3}.
3 Wait for the paged party to answer.
L If the paged party does not answer,
press {INTERCOM} to return to the
outside call.
45
Multi-unit Operation
KX-TG5672/KX-TG5673
Registering a handset
Important:
The included handset and base unit are
preregistered. If for some reason the
handset is not registered to the base unit,
register the handset. Lift the handset from
the base unit or charger before registering.
L If you accidentally assign another
handset’s extension number to the base
unit, the originally assigned handset
stops functioning. Confirm the extension
number of the handset by placing it on
the base unit or charger. Lift the handset
from the charger before registering.
KX-TG5671
1 Handset:
1 Handset:
{MENU} i {0}{0}
{MENU} i {0}{0}
2 Base unit:
2 Base unit:
Press and hold {INTERCOM} until the
CHARGE indicator flashes.
Press and hold {INTERCOM} until the
CHARGE indicator flashes, then press
{1}, {2}, or {3}.
L After the CHARGE indicator starts
flashing, the rest of the procedure
must be completed within 1 minute.
L After the CHARGE indicator starts
flashing, the rest of the procedure
must be completed within 1 minute.
3 Handset:
Press {OK}, then wait until the handset
3 Handset:
beeps.
Press {OK}, then wait until the handset
beeps.
Registering an additional handset
See page 5 for information on the available
models and extension numbers.
Start from step 2.
46
Useful Information
3 Adjust the adaptor to hold the base unit,
then push it in the direction of the arrow
until it clicks into place.
Wall mounting
Base unit
1 Tuck the telephone line cord inside the
wall mounting adaptor (A).
Connect the telephone line cord (B).
A
B
2 Insert the hooks on the wall mounting
adaptor into the holes (1) and (2) on
the base unit.
2
1
2
1
47
Useful Information
4 Connect the telephone line cord. Mount
the unit by inserting the mounting pins
into the round openings on the adaptor
(for pin 2, use round cut out at the
bottom of the adaptor if you are using
the 4 inches phone plate), then sliding
the unit down to secure it.
To remove the wall mounting adaptor
While pushing down the release levers
(A), remove the adaptor (B).
A
A
Connect the AC adaptor to power outlet
(page 11).
L There are two common types of wall
phone plates. The distance between
1 and 2 may vary depending on the
size of the wall phone plate installed.
B
1
83 mm
31/4 inches
)
(
or
102 mm
(4 inches)
2
(120 V AC,
60 Hz)
83 mm
102 mm
(4 inches)
31/4 inches
( )
1
2
48
Useful Information
Charger
Headset (optional)
Available model:
KX-TG5672/KX-TG5673
Connecting a headset to the handset
allows hands-free phone conversations.
Please use only a Panasonic headset
(page 7).
1 Drive the screws (not included) into the
wall using the wall template as a guide.
25.4 mm
(1 inch)
Screws
(120 V AC, 60 Hz)
2 Mount the charger (A), then slide it
down (B) and to the right (C) until it is
secure.
L Headset shown is KX-TCA86.
Switching a call between the headset
and handset speakerphone
To switch to the handset speakerphone,
press {s}.
A
B
To return to the headset, press {C}.
C
25.4 mm
(1 inch)
49
Useful Information
Error messages
If the unit detects a problem, one of the following messages is shown on the display.
Display message
Cause/solution
Busy
L The called base unit is in use.
L Another handset or the called handset is in use.
*1
L The handset you tried to copy phonebook items to is in
*1
use.
*1
L The handset you are calling is too far from the base unit.
Error!!
L The handset’s registration has failed. Move the handset
and base unit away from all electrical appliances and try
again.
L Another handset user tried to send phonebook items to
you but there was an error. Have the other handset user
*1
re-send the items to you (page 26).
---Incomplete---
Phonebook full
L The destination unit’s phonebook memory is full. Erase
unnecessary items from the destination unit’s
phonebook (page 25).
*1
*1
Invalid
L There is no handset registered to the base unit
matching the extension number you entered.
No items stored
L Your phonebook or redial list is empty.
No link to base.
Move closer to
base, try again.
L The handset has lost communication with the base unit.
Move closer to the base unit, and try again.
L Confirm that the base unit’s AC adaptor is plugged in.
L Raise the base unit antennas.
L The handset’s registration may have been canceled.
Re-register the handset (page 46).
Phonebook full
L There is no space to store new items in the phonebook.
Erase unnecessary items (page 25).
Please lift up and
try again.
L A handset button was pressed while the handset was
on the base unit or charger. Lift the handset and press
the button again.
System is busy.
Please try again
later.
L Other units are in use and the system is busy. Try again
later.
L Another user is listening to messages. Try again later.
*1 KX-TG5672/KX-TG5673
50
Useful Information
Troubleshooting
General use
Problem
Cause/solution
The unit does not work.
L Make sure the battery is installed correctly and fully
charged (page 12, 13).
L Check the connections (page 11).
L Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
L The handset has not been registered to the base unit.
Register the handset (page 46).
I cannot hear a dial tone.
L Confirm the telephone line cord is properly connected
(page 11).
L Disconnect the unit from the telephone line and connect
a known working telephone. If the working telephone
operates properly, contact our service personnel to
have the unit repaired. If the working telephone does
not operate properly, contact your telephone company.
Programmable settings
Problem
Cause/solution
I cannot program items.
L While another user is listening to messages or the
answering system is answering a call, you cannot
program items. Try again later.
While programming, the
handset starts to ring.
L A call is being received. Answer the call and start again
after hanging up.
Battery recharge
Problem
Cause/solution
I charged the battery fully,
but 7 continues to
flash, or 8 is
L Clean the charge contacts and charge again (page 13).
L The battery may need to be replaced with a new one
(page 12).
displayed.
The handset display is
blank.
L Confirm that the battery is properly installed.
L Fully charge the battery (page 13).
51
Useful Information
Making/answering calls, intercom
Problem
Cause/solution
Static is heard, sound
cuts in and out.
L Move the handset and the base unit away from other
electrical appliances.
Interference from other
electrical units.
L Move closer to the base unit.
L Raise the base unit antennas.
L Turn on the clarity booster feature (page 22).
L If your unit is connected to a telephone line with DSL
service, we recommend connecting a noise filter
between the base unit and the telephone line jack.
Contact your DSL provider for details.
The handset and base
unit do not ring.
L The ringer volume is turned off. Adjust it (page 21, 34).
I cannot make a call.
L The dialing mode may be set incorrectly. Change the
setting (page 18).
L The base unit or another handset is in use. Try again
later.
I cannot redial by
pressing {REDIAL}.
L If the last number dialed was more than 48 digits long,
the number will not be redialed correctly. Dial the
number manually.
I cannot have a
conversation using the
headset.
L Make sure that an optional headset is connected
properly (page 49).
L If “SP-phone” is displayed on the handset, press {C}
to switch to the headset.
I cannot make long
distance calls.
L Make sure that you have long distance service.
I cannot page the
L The called handset is too far from the base unit.
handset or base unit.
L The called unit is in use. Try again later.
The Slow Talk feature
does not work.
L If you are on a conference call, you cannot use the Slow
Talk feature.
L If another handset is having an intercom call with the
*1
base unit, you cannot use the Slow Talk feature.
L If someone is operating the answering system, you
cannot use the Slow Talk feature.
*1 KX-TG5672/KX-TG5673
52
Useful Information
Phonebook
Problem
Cause/solution
Copying stopped with an
item displayed.
L The destination handset may have lost communication
with the base unit, or the destination unit user may have
pressed {C} or {s}.
*1
The displayed phonebook item was not copied to the
unit. Press {OFF}. Confirm that the destination unit is
not in use and try again.
*1 KX-TG5672/KX-TG5673
Caller ID
Problem
Cause/solution
The handset does not
display the caller’s name
and/or phone number.
L You have not subscribed to Caller ID service. Contact
your telephone company to subscribe.
L If your unit is connected to any additional telephone
equipment such as a Caller ID box or cordless
telephone jack, disconnect the unit from the equipment
and plug the unit directly into the wall jack.
L If your unit is connected to a telephone line with DSL
service, we recommend connecting a noise filter
between the base unit and the telephone line jack.
Contact your DSL provider for details.
L The name display service may not be available in some
areas. Contact your telephone company for details.
L Other telephone equipment may be interfering with this
unit. Disconnect the other equipment and try again.
L The caller requested not to send caller information
(page 28).
L If a call is being transferred to you, the caller information
is not displayed.
The handset or base unit
does not announce the
displayed caller names.
L The handset or base unit’s ringer volume is turned off.
Adjust it (page 21, 34).
L The Talking Caller ID feature is turned off. Turn it on
(page 35).
L The ring count for the answering system is set to “2” or
“Toll saver”. Select a different setting (page 41).
L If the base unit and another handset are having an
intercom call, your handset does not announce caller
*1
information.
53
Useful Information
Problem
Cause/solution
The caller list/incoming
phone numbers are not
edited automatically.
L The Caller ID number auto edit feature is turned off.
Turn it on and try again (page 34).
L You need to call back the edited number to activate
Caller ID number auto edit.
I cannot dial the phone
number edited in the
caller list.
L The phone number you dialed might have an incorrectly
edited pattern (for example, the long distance “1” or the
area code is missing). Edit the phone number with
another pattern (page 30).
The 2nd caller’s
information is not
displayed during an
outside call.
L In order to use Caller ID, Call Waiting, or Call Waiting
Caller ID (CWID), you must first contact your telephone
company and subscribe to the desired service.
After subscribing, you may need to contact your
telephone company again to activate this specific
service, even if you already subscribed to both Caller ID
and Call Waiting with Caller ID services (CWID).
*1 KX-TG5672/KX-TG5673
Answering system
Problem
Cause/solution
I cannot listen to
messages from a remote
location.
L A touch tone phone is required for remote operation.
L Enter the remote code correctly (page 39).
L The answering system is off. Turn it on (page 40).
The unit does not record
new messages.
L The answering system is off. Turn it on (page 40).
L The recording time is set to “Greeting only”. Select
a different setting (page 42).
L The message memory is full. Erase unnecessary
messages (page 37).
L If you subscribe to the Voice Mail service, messages
are recorded by the telephone company not your
telephone (page 41).
I cannot operate the
answering system.
L Someone is operating the answering system.
L If someone is talking on a conference call, you cannot
operate the answering system. Try again later.
*1
The message indicator
on the handset flashes.
L New messages have been recorded. Listen to the new
messages (page 37).
*1 KX-TG5672/KX-TG5673
54
Useful Information
FCC and other information
This equipment complies with Part 68 of
the FCC rules and the requirements
adopted by the ACTA. On the bottom of
this equipment is a label that contains,
among other information, a product
identifier in the format US:ACJ----------.
If requested, this number must be
provided to the telephone company.
L Registration No
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the
telephone network, the telephone
company will notify you in advance that
temporary discontinuance of service may
be required. But if advance notice isn’t
practical, the telephone company will
notify the customer as soon as possible.
Also, you will be advised of your right to
file a complaint with the FCC if you
believe it is necessary.
............(found on the bottom of the unit)
L Ringer Equivalence No.
(REN).......0.1B
A plug and jack used to connect this
equipment to the premises wiring and
telephone network must comply with the
applicable FCC Part 68 rules and
requirements adopted by the ACTA. A
compliant telephone cord and modular
plug is provided with the product. It is
designed to be connected to a
The telephone company may make
changes in its facilities, equipment,
operations or procedures that could
affect the operation of the equipment. If
this happens the telephone company will
provide advance notice in order for you
to make necessary modifications to
maintain uninterrupted service.
compatible modular jack that is also
compliant.
If trouble is experienced with this
equipment, for repair or warranty
information, please contact a Factory
Servicenter or other Authorized Servicer.
If the equipment is causing harm to the
telephone network, the telephone
company may request that you
disconnect the equipment until the
problem is resolved.
The REN is used to determine the
number of devices that may be
connected to a telephone line. Excessive
RENs on a telephone line may result in
the devices not ringing in response to an
incoming call. In most but not all areas,
the sum of RENs should not exceed five
(5.0). To be certain of the number of
devices that may be connected to a line,
as determined by the total RENs, contact
the local telephone company. For
products approved after July 23, 2001,
the REN for the product is part of the
product identifier that has the format
US:AAAEQ##TXXXX. The digits
Connection to party line service is
subject to state tariffs. Contact the state
public utility commission, public service
commission or corporation commission
for information.
If your home has specially wired alarm
equipment connected to the telephone
represented by ## are the REN without a
55
Useful Information
line, ensure the installation of this
equipment does not disable your alarm
equipment. If you have questions about
what will disable alarm equipment,
consult your telephone company or a
qualified installer.
Privacy of communications may not be
ensured when using this phone.
CAUTION:
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
device.
This equipment is hearing aid compatible
as defined by the FCC in 47 CFR Section
68.316.
NOTE:
When you hold the phone to your ear,
noise might be heard in your Hearing Aid.
Some Hearing Aids are not adequately
shielded from external RF (radio
frequency) energy. If noise occurs, use
an optional headset accessory or the
speakerphone option (if applicable) when
using this phone. Consult with your
audiologist or Hearing Aid manufacturer
about the availability of Hearing Aids
which provide adequate shielding to RF
energy commonly emitted by digital
devices.
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
WHEN PROGRAMMING EMERGENCY
NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain
to the dispatcher the reason for the
call.
2) Perform such activities in the off-peak
hours, such as early morning or late
evenings.
- Reorient or relocate the receiving
antenna.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
- Consult the dealer or an experienced
radio/TV technician for help.
56
Useful Information
Some cordless telephones operate at
frequencies that may cause interference
to nearby TVs and VCRs. To minimize or
prevent such interference, the base of
the cordless telephone should not be
placed near or on top of a TV or VCR. If
interference is experienced, move the
cordless telephone further away from the
TV or VCR. This will often reduce, or
eliminate, interference.
Notice
FCC RF Exposure Warning:
The product complies with FCC radiation
exposure limits set forth for an
uncontrolled environment. To comply
with FCC RF exposure requirements, the
base unit must be installed and operated
with its antenna located 20 cm (8 inches)
or more between antenna and all
person’s body (excluding extremities of
hands, wrist and feet). The handset may
be carried and operated with only the
optional specific belt-clip. Other non-
tested belt-clips or similar body-worn
accessories may not comply and must
be avoided. The product must not be
collocated or operated in conjunction
with any other antenna or transmitter.
57
Useful Information
Specifications
General
Operating environment
Frequency
5 °C – 40 °C (41 °F – 104 °F)
5.76 GHz – 5.84 GHz
Base unit
Dimensions
Approx. height 96 mm x width 210 mm x depth 157 mm
25
1
3
(3
/
inches x 8 / inches x 6 / inches)
32 16
4
Mass (Weight)
Approx. 405 g (0.89 lb.)
Power consumption
Standby: Approx. 2.2 W/1.5 W (PQLV1/PQLV256)
Maximum: Approx. 4.7 W/3.8 W (PQLV1/PQLV256)
Power output
Power supply
200 mW (max.)
AC adaptor (120 V AC, 60 Hz)
Handset
Dimensions
Approx. height 173 mm x width 48 mm x depth 33 mm
13
7
5
(6
/
inches x 1 / inches x 1 / inches)
16 16
8
Mass (Weight)
Power output
Power supply
Approx. 170 g (0.37 lb.)
200 mW (max.)
Ni-MH battery (3.6 V, 830 mAh)
*1
Charger
Dimensions
Approx. height 51 mm x width 88 mm x depth 100 mm
15
15
(2 inches x 3
/
inches x 3
/
inches)
32
16
Mass (Weight)
Approx. 94 g (0.21 lb.)
Power consumption
Standby: Approx. 0.8 W/0.3 W (KX-TCA1/PQLV256)
Maximum: Approx. 3.6 W/2.4 W (KX-TCA1/PQLV256)
Power supply
*1 KX-TG5672/KX-TG5673
Note:
AC adaptor (120 V AC, 60 Hz)
L Design and specifications are subject to change without notice.
L The illustrations in these instructions may vary slightly from the actual product.
58
Useful Information
Warranty
PANASONIC CONSUMER
ELECTRONICS COMPANY, DIVISION
OF PANASONIC CORPORATION OF
NORTH AMERICA
PANASONIC PUERTO RICO, INC.
San Gabriel Industrial Park,
Ave. 65 de Infantería, Km. 9.5,
Carolina, Puerto Rico 00985
One Panasonic Way,
Secaucus, New Jersey 07094
Panasonic Telephone Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto
Rico, Inc. (collectively referred to as “the warrantor”) will, for the length of the period
indicated on the chart below, which starts with the date of original purchase
(“Limited Warranty period”), at its option either (a) repair your product with new or
refurbished parts, or (b) replace it with a new or a refurbished product. The decision
to repair or replace will be made by the warrantor.
Parts
One (1) Year
Labor
One (1) Year
During the “Labor” Limited Warranty period there will be no charge for labor. During
the “Parts” Limited Warranty period, there will be no charge for parts. You must
mail-in your product prepaid during the Limited Warranty period. This Limited
Warranty excludes both parts and labor for batteries, antennas, and cosmetic parts
(cabinet). This Limited Warranty only applies to products purchased and serviced in
the United States or Puerto Rico. This Limited Warranty is extended only to the
original purchaser and only covers products purchased as new.
Mail-In Service
For assistance in the continental U.S.A. in obtaining repairs please ship the product
prepaid to:
Panasonic Services Company Customer Servicenter
4900 George McVay Drive Suite B Door #12 McAllen, TX 78503
For assistance in Puerto Rico call Panasonic Puerto Rico, Inc. (787)-750-4300 or
fax (787)-768-2910.
For Limited Warranty service for headsets if a headset is included with this product
please call Panasonic Call Center at 1-800-211-PANA (1-800-211-7262).
When shipping the unit carefully pack, include all accessories, and send it prepaid,
adequately insured and preferably in the original carton. Include a letter detailing
the complaint and provide a day time phone number where you can be reached.
59
Useful Information
IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF
OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND
PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR
OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And Exclusions
This Limited Warranty ONLY COVERS failures due to defects in materials or
workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage.
The Limited Warranty ALSO DOES NOT COVER damages which occurred in
shipment, or failures which are caused by products not supplied by the warrantor,
or failures which result from accidents, misuse, abuse, neglect, bug infestation,
mishandling, misapplication, alteration, faulty installation, set-up adjustments,
misadjustment of consumer controls, improper maintenance, power line surge,
lightning damage, modification, introduction of sand, humidity or liquids,
commercial use such as hotel, office, restaurant, or other business or rental use of
the product, or service by anyone other than a Factory Servicenter or other
Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE
OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS LIMITED
WARRANTY. (As examples, this excludes damages for lost time, lost calls or
messages, cost of having someone remove or re-install an installed unit if
applicable, travel to and from the servicer. The items listed are not exclusive, but
are for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so the exclusions
may not apply to you.
This Limited Warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If a problem with this product develops during or
after the Limited Warranty period, you may contact your dealer or Servicenter. If the
problem is not handled to your satisfaction, then write to the warrantor’s Consumer
Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY, ARE YOUR RESPONSIBILITY.
60
Useful Information
Customer services
Customer Services Directory
Obtain Product Information and Operating Assistance; locate your nearest Dealer or
Servicenter; purchase Parts and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
or, contact us via the web at:
You may also contact us directly at: 1-800-211-PANA (1-800-211-7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
TTY users (hearing or speech impaired users) can call 1-877-833-8855.
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic
Products by visiting our Web Site at:
or, send your request by E-mail to:
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday - Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal
Checks)
TTY users (hearing or speech impaired users) can call 1-866-605-1277.
Service in Puerto Rico
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5,
Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
61
Index
G Greeting message: 36
H Handset locator: 43
Headset, optional: 49
Hold: 21
Index
A Answering calls: 20
Answering system
I
Installation
Erasing messages: 37, 38, 40
Listening to messages: 37, 38, 39
Turning on/off: 36, 38, 40
Auto talk: 20
Base unit: 11
Handset: 12
Intercom: 43
K Key tone: 34
B Battery
L
Light-up ID: 29
Line mode: 35
Charge: 13
Installation: 12
Level: 14
Performance: 14
Replacement: 12
Booster (Clarity booster): 22
M Making calls: 19
MEMO: 39
Memory capacity (message
recording): 36
Message alert: 42
Missed calls: 28, 30
Mute: 22
C Call screening: 36
Call share: 23
Call Waiting: 22
Call Waiting Caller ID: 28
Caller ID edit: 30
Caller ID number auto edit: 30
Caller ID service: 28
Caller list
N Navigator key: 16
P
Pause: 19, 27
Phonebook: 24
Phonebook copy: 26
Pulse service: 22
R Recording time: 42
Redial list: 19
Calling back: 30
Editing: 30
Registration: 46
Remote code: 41
Remote operation: 39
Ring color: 34
Ring count: 41
Ringer ID: 29
Erasing: 31
Storing: 31
Viewing: 30
Chain dial: 25
Conference calls: 44
Connections: 11, 12
Customer support: 35
Ringer off
Base unit: 21
Handset: 20, 34
Ringer tone
Base unit: 21
Handset: 34
D Date and time: 18
Dialing mode: 18
Display
Contrast: 34
Language: 18
Rotary service: 22
E
F
Error messages: 50
S
Slow Talk: 23
Soft keys: 17
Flash: 22
Flash time: 35
62
Index
Speed dialer: 27
SP-phone: 19
T
V
Talking Caller ID: 28
Time adjustment: 35
Toll saver: 41
Tone: 22
Transferring calls: 44
Troubleshooting: 51
TTY: 7, 61
VE (Voice Enhancer): 23
Voice guidance: 38, 40
Volume
Base unit ringer: 21
Base unit speaker: 20
Handset receiver: 19
Handset ringer: 34
Handset speaker: 19
W Wall mounting
Base unit: 47
Charger: 49
Warranty: 59
63
If you need assistance with setup or operation
3 Call us at: 1-800-211-PANA (1-800-211-7262)
TTY users (hearing or speech impaired users) can call 1-877-833-8855.
When you ship the product
L Carefully pack your unit, preferably in the original carton.
L Attach a letter, detailing the symptom, to the outside of the carton.
L Send the unit to Panasonic Services Company Customer Servicenter, prepaid and
adequately insured.
L Do not send your unit to Panasonic Consumer Electronics Company listed below or to
executive or regional sales offices. These locations do not repair consumer products.
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5,
Carolina, Puerto Rico 00985
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. All other reproduction, in whole or in part, is prohibited
without the written consent of Panasonic Communications Co., Ltd.
© 2005 Panasonic Communications Co., Ltd. All Rights Reserved.
PQQX15043ZA DM1205SY1016
|