Omega Lift 13200 User Manual

Operating Instructions  
& Parts Manual  
Hydraulic Toe Jacks  
Model Number  
13120  
Capacity  
6 Ton  
13200  
10 Ton  
Shinn Fu Co. of America, Inc. ©2002  
10939 N. Pomona Avenue  
Kansas City, MO 64153  
OIPM # 13120-TJ2  
Printed in Taiwan  
!
WARNING  
WARNING  
!
Study, understand, and follow all instructions before  
operating this device. Do not exceed rated capacity.  
Use only on hard, level surfaces. Lifting device only.  
Immediately after lifting, support the vehicle with  
appropriate means. Failure to heed these markings  
may result in personal injury and/or property  
damage.  
OPERATION  
Lifting  
1. Assemble 3 pc. handle, ensure that spring clips  
align with slots.  
2. Secure the load to prevent inadvertent shifting and  
movement.  
3. Position the jack near desired lift point.  
4. Close the release valve by turning it clockwise until  
it is firmly closed.  
To avoid crushing and related injuries:  
NEVER work on, under or around a load supported  
only by a jack. ALWAYS use adequately rated jack  
stands.  
OPERATION (continued)  
Lowering  
1. Raise load enough to carefully remove jack stands.  
2. Insert handle onto release valve and slowly turn  
handle counterclockwise, but no more than 1/2  
turn.  
Note: Use the handle provided with this product or an  
authorized replacement handle to ensure proper  
release valve operation. When using to lift vehicle, lift  
only on the manufacturer’s recommended lift points  
and in accordance with the published guidelines in  
your vehicle owners manual. Always use jack stands  
to support the load immediately after lifting.  
3. If load fails to lower:  
a. Carefully transfer the load to another lifting  
device and jack stands.  
b. Carefully remove affected jack, and then the  
jack stands. Lower the load, again by slowly  
turning the release valve no more than 1/2 turn.  
5. Insert and secure handle into handle sleeve. Pump  
handle until saddle contacts load.  
6. Raise load to desired height, then immediately  
transfer the load to appropriately rated support  
devices such as jack stands.  
! SAFETY MESSAGE !  
Be sure all tools and personnel are clear before  
lowering load. No alterations shall be made to this  
device. Only attachments and/or adapters supplied  
by the manufacturer shall be used.  
4. After removing jack from under the load, push ram  
and handle sleeve down to reduce exposure to rust  
and contamination.  
OIPM#13120-TJ2  
3
MAINTENANCE  
MAINTENANCE (continued)  
Note: Dispose of hydraulic fluid in accordance with  
local regulations.  
Important: Use only a good grade hydraulic jack oil.  
Avoid mixing different types of fluid and NEVER use  
brake fluid, turbine oil, transmission fluid, motor oil or  
glycerin. Improper fluid can cause premature failure  
of the jack and the potential for sudden and immediate  
loss of load. We recommend Mobil DTE 13M.  
3. Fill with good quality jack oil. Reinstall oil filler plug/  
screw.  
Lubrication  
Adding oil  
1. A coating of light lubricating oil to pivot points, axles  
and hinges will help to prevent rust and assure that  
assemblies move freely.  
2. Periodically check the pump piston and ram for  
signs of rust or corrosion. Clean as needed and  
wipe with a clean, oil soaked rag.  
1. With saddle fully lowered and pump piston fully  
depressed, set jack in its upright, level position.  
Remove oil filler plug/screw.  
2. Fill until oil is level with the filler plug/screw hole,  
reinstall oil filler plug/screw.  
Changing oil  
Never use sandpaper or abrasive material on  
these surfaces !  
For best performance and longest life, replace the  
complete fluid supply at least once per year.  
1. With saddle fully lowered and pump piston fully  
depressed, remove the oil filler plug/screw.  
2. Lay the jack on its side and drain the fluid into a  
suitable container.  
Storage  
When not in use, store the jack with pump piston and  
ram fully retracted.  
TROUBLESHOOTING  
Symptom  
Possible Causes  
Corrective Action  
• Ensure release valve tightly closed  
• Remedy overload condition  
• Release valve not tightly closed  
• Overload condition  
Jack will not lift load  
• Release valve not tightly closed  
• Overload condition  
• Ensure release valve tightly closed  
• Remedy overload condition  
Jack bleeds off after lift  
• Hydraulic unit malfunction  
• Contact Omega Tech. Service  
• Reservoir overfilled  
• Linkages binding  
• Drain fluid to proper level  
• Clean and lubricate moving parts  
Jack will not lower after unloading  
Poor lift performance  
• Fluid level low  
• Air trapped in system  
• Ensure proper fluid level  
• With ram fully retracted, remove oil filler  
plug to let pressurized air escape, then  
reinstall oil filler plug  
• Fluid level low  
Will not lift to full extension  
• Ensure proper fluid level  
OIPM#13120-TJ2  
4
ONE YEAR LIMITED WARRANTY  
For a period of one (1) year from date of purchase, Shinn Fu Co. of America, Inc. will repair or replace,  
at its option, without charge, any of its products which fails due to a defect in material or workmanship, or which  
fails to conform to any implied warranty not excluded hereby.  
Performance of any obligation under this warranty may be obtained by returning the warranted product,  
freight prepaid, to Shinn Fu Co. of America, Inc. Warranty Service Department, 10939 N. Pomona Ave., Kansas  
City, MO 64153.  
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) the  
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE  
PRODUCTS AS DESCRIBED ABOVE, and (2) Shinn Fu Co. of America, Inc. SHALL NOT BE LIABLE FOR ANY  
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE DURATION OF ANY AND  
ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE (1)  
YEAR FROM DATE OF PURCHASE.  
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not  
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the  
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also  
have other rights which vary from state to state.  
OIPM#13120-TJ2  
5
REPLACEMENT PARTS  
Available Parts: Please refer to the Parts drawing when ordering parts. Not all components of the jack are  
replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence.  
When ordering parts, give Model number, serial number and description below. Call or write for current pricing:  
Shinn Fu Company of America, Inc. 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A. Tel:(888)332-6419  
Model # 13120 & 13200  
Parts No.  
Description  
Quantity  
1
2
3
4
--  
--  
oil filler plug / screw*  
handle assembly  
return spring  
saddle bracket  
label(s) (not shown)  
manual (OIPM # 13120-TJ2)  
1
1
2
1
1
1
* oil filler screw for 13200  
2
1
4
3
Figure 2 - Model 13120 & 13200 Replacement Parts Illustration  
6
OIPM#13120-TJ2  
Notes  
Shinn Fu Company of America, Inc.  
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.  
Tel:(888)332-6419 Fax:(816)891-6599 E-Mail:[email protected] Omega Website: http://www.omegalift.com  
Notes  
Shinn Fu Company of America, Inc.  
10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.  
Tel:(888)332-6419 Fax:(816)891-6599 E-Mail:[email protected] Omega Website: http://www.omegalift.com  

Samsung Uq30c1 2 Bc User Manual
Sanyo Kr Ch 20 User Manual
Sharp Mx De11 User Manual
Soleus Air Pe3 12r 03 User Manual
Sterling Power Products Ab24100 User Manual
Trion Air Boss Imp 38 User Manual
Tripp Lite Srcool12k User Manual
Xerox Et 6124 User Manual
Xerox Nuvera 100 Ea User Manual
Xerox Pro 575 User Manual