Zenoah Trimmer eHT600D User Manual

T4521-93110(205)

OWNER’S MANUAL

HEDGE-TRIMMERS

eHT750S

eHT600D

• Before using our products,

please read this manual

carefully to understand the

proper use of your unit.

• Keep this manual handy.

CAUTION

Download from Www.Somanuals.com. All Manuals Search And Download.

English

1. PARTS LOCATION

1. Plate receive

2. Right handle

3. Starter

4. Fuel cap

5. Left handle

6. Engine Stop switch

7. Throttle lever

8. Fuel tank

9. Muffler

10. Blade

11. Air cleaner

12. Spark plug

13. Gear case

14. Throttle cable

15. Choke lever

16. Front handle

17. Engine switch

18. Safty lock lever

19. Rear handle

20. Lock lever

21. Grease nipple

Download from Www.Somanuals.com. All Manuals Search And Download.

English

2. SYMBOLS ON THE MACHINE

For safe operation and maintenance,

symbols are carved in relief on the

machine. According to these

indications, please be careful not to

take a mistake.

(a).The port to refuel the "MIX

GASOLINE"

POSITION: FUEL TANK CAP

(b).The direction to close the choke

POSITION: AIR CLEANER COVER

(c).The direction to open the choke

POSITION: AIR CLEANER COVER

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

■ BEFORE USING THE MACHINE

a. Read this owner's manual

carefully to understand how to

operate this unit properly.

b. This product has been designed

for use in trimming leaves and

branches from trees and hedges,

and it should never be used for

any other purpose since doing so

could result in unforeseen

accidents and injuries occurring.

c. You should never use this hedge-

trimmer when under the influence

of alcohol, when suffering from

exhaustion or lack of sleep, when

suffering from drowsiness as a

result of having taken cold

medicine, or at any other time

when a possibility exists that your

judgment might be impaired or

that you might not be able to

operate the hedge-trimmer

properly and in a safe manner.

d. Avoid running the engine indoors.

The exhaust gases contain

harmful carbon monoxide.

e. Never use your hedge-trimmer

under circumstances like those

described below:

1. When the ground is slippery or

when other conditions exist

which might make it not

possible to maintain a steady

posture while using the hedge-

trimmer.

2. At night, at times of heavy fog,

or at any other times when your

field of vision might be limited

and it would be difficult to gain a

clear view of the area.

3. During rain storms, during

lightning storms, at times of

strong or gale-force winds, or at

any other times when weather

conditions might make it unsafe

to use this product.

f. When using this product for the

first time, before beginning actual

work, learn to handling the hedge-

trimmer from skilled worker.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

g. Lack of sleep, tiredness, or

physical exhaustion results in

lower attention spans, and this in

turn leads to accidents and injury.

Limit the amount of time over

which the hedge-trimmer is to be

used continuously to somewhere

around 30~40 minutes per

session, and take 10~20 minutes

of rest between work sessions.

Also try to keep the total amount

of work performed in a single day

under 2 hours or less.

h. Be sure to keep this manual

handy so that you may refer to it

later whenever any questions

arise.

i. Always be sure to include this

manual when selling, lending, or

otherwise transferring the

ownership of this product.

j. Never allow children or anyone

unable to fully understand the

directions given in this manual to

use this hedge-trimmer.

■

WORKING GEAR AND CLOTHING

a. When using your hedge-trimmer,

you should wear proper clothing

and protective equipment as

follows.

(1) Helmet

(2) Protection goggles or face

protector

(3) Thick work gloves

(4) Non-slip-sole work boots

(5) Ear protectors

b. And you should carry with you

things as follows.

1. Attached tools and files

2. Properly reserved fuel

3. Spare blade

4. Things to notify your working

area (Rope, warning signs)

5. Whistle (for collaboration or

emergency)

6. Hatchet or saw (for removal of

obstacles)

c. Never use your hedge-trimmer

when wearing pants with loose

cuffs, when wearing sandals, or

when barefoot.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

■ WARNING

CONSIDERING

HANDLING OF FUEL

a. The engine of this product is

designed to run on a mixed fuel

which contains highly flammable

gasoline. You should never store

cans of fuel or refill the fuel tank in

any place where there is a boiler,

stove, wood fire, electrical sparks,

welding sparks, or any other

source of heat or fire which might

ignite the fuel.

b. Smoking while operating the

hedge-trimmer or refilling its fuel

tank is extremely dangerous.

Always be sure to keep lit

cigarettes away from the hedge-

trimmer at all times.

c. When refilling the tank always turn

off the engine first and take a

careful look around to make sure

that there are no sparks or open

flames anywhere nearby before

refueling.

d. If any fuel spillage occurs during

refueling, use a dry rag to wipe up

spills before turning the engine

back on again.

e. After refueling, screw the fuel cap

back tightly onto the fuel tank and

then carry the hedge-trimmer to a

spot 3m or more away from where

it was refueled before turning on

the engine.

■ THINGS TO CHECK BEFORE

USING YOUR HEDGE-TRIMMER

a. Before beginning work, look

around carefully to get a feel for

the shape of the land, or grass to

be trimmed, and whether or not

there are any obstacles which

might get in the way while

working, and remove any

obstacles which can be cleared

away.

b. The area within a perimeter of

15m of the person using the

hedge-trimmer

should

considered a hazardous area into

which no one should enter while

the hedge-trimmer is in use, and

when necessary yellow warning

rope, warning signs should be

placed around the work area.

When work is to be performed

simultaneously by two or more

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

persons, always check the

presence and locations of others

so as to maintain a distance each

person sufficient to ensure safety.

c. Make sure that there are no loose

screws or bolts, fuel leaks,

ruptures, dents, or any other

problems which might interfere

with safe operation. Be especially

careful to check that there is

nothing wrong with the blades or

with the joints by which the blades

are attached to the hedge-

trimmer.

d. Never use blades that are bent,

warped, cracked, broken or

damaged in any way.

e. Keep the blade always sharp.

f. Filing the cutting edges, keep the

end corner sharp and round the

root of the edge.

g. Check the bolt to fasten the blade

and be sure the blade turns

smoothly without abnormal noise.

■ NOTES ON STARTING THE

ENGINE

1. Take a careful look around to

make sure that no obstacles exist

within a perimeter of 15m or less

around hedge-trimmer.

2. Place the body of the hedge-

trimmer onto the ground in a flat

clear area and hold it firmly in

place so as to ensure that neither

the blades nor the throttle come

into contact with any obstacles

when the engine starts up.

3. Place the throttle into the idling

position when starting the engine.

4. After starting up the engine, if the

blades continue to rotate even

after the throttle has been moved

fully back, turn off the engine and

check the throttle wire and other

parts.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

■

KICKBACK SAFETY PRECAUTIONS

A dangerous reaction may occur

when the spinning blade contacts

a solid object in the critical area.

It is called Kick back. As a result,

the operator can lose control of

the unit which can cause serious

or fatal injury.

•

Avoid kickback, observe the

safety precautions below strictly.

1. Keep the cutting blades clear of

fances, posts, wires, and rocks to

prevent kickback and damage to

the blades.

2. When using your hedge-trimmer,

do not grip other parts except the

handles.

3. When using your hedge-trimmer,

never take your eyes off. If you

need to, place the throttle into the

idling position.

4. When using your hedge-trimmer,

do not let the unit get closer to

your feet nor raise the unit above

your waist.

■ NOTES ON TRANSPORTATION

a. Make sure the appropriate blade

cover is in place.

b. When transporting by car, fix the

unit firmly using a rope. Do not

transport by bicycle or motorbike

because it is dangerous.

c. Never transport the hedge-

trimmer over rough roads over

long distances without first

removing all fuel from the fuel

tank, as doing so might cause fuel

to leak from the tank.

■

OPERATION SAFETY PRECAUTIONS

a. Grip the handles of the hedge-

trimmer firmly with both hands. If

you suspend the work, place the

throttle into the idling position.

b. Always be sure to maintain a

steady, even posture while

working.

c. Maintain the speed of the engine

at the level required to perform

cutting work, and never raise the

speed of the engine above the

level necessary.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

d. If the grass gets caught in the

blade during operation, or if you

need to check the unit or refuel

the tank, always be sure to turn off

the engine.

e. If the blade touches a hard object

like a stone, immediately stop the

engine and check if something is

wrong with the blade. If so,

replace the blade by new one.

f. If someone calls out while working

,always be sure to turn off the

engine before turning around.

g. Never touch the spark plug or plug

cord while the engine is in

operation. Doing so may result in

being subjected to an electrical

shock.

h. Never touch the muffler, spark

plug, or other metallic parts of the

engine while the engine is in

operation or immediately after

shutting down the engine. Doing

so may result in serious burns.

i. When you finish cutting in one

location and wish to continue work

in another spot, turn off the engine

and turn the unit as the blade

faces away from your body.

■ MAINTENANCE

SAFETY

PRECAUTION

a. Perform the maintenance and

checking operations described in

this manual at regular intervals. If

any parts must be replaced or any

maintenance or repair work not

described in this manual must be

performed, please contact a

representative from the store

nearest KOMATSU ZENOAH

authorized servicing dealer for

assistance.

b. Under no circumstances should

you ever take apart the hedge-

trimmer or alter it in any way.

Doing so might result in the

hedge-trimmer

becoming

damaged during operation or the

hedge-trimmer becoming unable

to operate properly.

c. Always be sure to turn off the

engine before performing any

maintenance

procedures.

checking

Download from Www.Somanuals.com. All Manuals Search And Download.

English

3. SAFETY PRECAUTIONS

d. When sharpening, removing, or

reattaching the blade, be sure to

wear thick, sturdy gloves and use

only proper tools and equipment

to prevent injury.

e. When replacing blade or any other

parts or when replacing the oil or

any lubricants, always be sure to

use only KOMATSU ZENOAH

products or products which have

been certified by KOMATSU

ZENOAH for use with the hedge-

trimmer.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

4. FUEL

WARNING

• Gasoline is very flammable.

Avoid smoking or bringing any

flame or sparks near fuel.

• Wipe up all spills before

starting the engine.

• Make sure to stop the engine

and allow it cool before

refueling the unit.

• Keep open flames away from

the area where fuel is handled

or stored.

IMPORTANT

• Never use oil for 4 cycle engine

use or water cooled 2-cycle

engine. It can cause spark plug

fouling, exhaust port blocking, or

piston ring sticking.

• Mixed fuels which have been left

unused for a period of one month

or more may clog the carburetor

or result in the engine failing to

operate properly. Put remained

fuel into an air-tight container and

keep it in the dark and cool room.

Mix a regular grade gasoline (leaded

or unleaded, alcohol-free) and a

quality-proven motor oil for air cooled

2 cycle engines.

RECOMMENDED MIXING RATIO

Gasoline 25 : Oil 1

Download from Www.Somanuals.com. All Manuals Search And Download.

English

5. OPERATION

■ STARTING THE ENGINE

WARNING

Keep the blades clear of

everything around It as they will

start moving upon the engine

starts.

1. [eHT750S] Make sure that the

throttle lever is at idling position.

[eHT600D] Release the throttle

lever and make sure it is fully

back. (F1)

2. [eHT600D] Set the engine switch

to the “I (RUN)” position. (F1)

3. Push the primer pump until

overflown fuel flows out in the

clear tube. (F2)

4. Move the choke lever to the

closed position. (F3)

(1) Throttle lever

(2) Full throttle

(7) Stop

(8) Primer pump

(3) Idling (start position) (9) Clear tube

(4) Stop switch

(5) Engine switch

(6) Run

(10) Choke lever

(11) Open

(12) Close

5. Place the unit on a flat, firm place.

Keep the cutting head clear of

everything around it.

6. While holding the unit firmly, pull

out the starter rope quickly. (F4)

7. After the engine has started, allow

the engine to warm up. Pull the

throttle lever.

■ STOPPING THE ENGINE (F1)

[eHT750S]

1. Please return the throttle lever

completely.

2. Press the stop switch until the

engine comes to a complete stop.

[eHT600D]

1. Release the throttle lever.

2. Move the engine switch to the

“O(STOP)”position.

NOTE

If the engine doesn’t stop after

stopping the switch, close the choke

so that engine will stop after a little.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

5. OPERATION

■ CUTTING WORK

WARNING

• Weather conditions and altitude

may effect carburation.

• Do not allow anyone to stay

close to the hedge-trimmer

while working or while

adjusting the carburetor.

■ HOW TO USE

HANDLE [eHT600D only] (F5)

To reduce fatigue when trimming

hedges, the handle can be swivelled

through 90° to the left or right.

F5 [eHT600D]

Do not press the throttle during

this operation!

Proceed as follows:

1. Free the handle by pressing the

locking lever.

2. Turn the handle until the locking

lever clicks into place.

3. When the handle is locked in its

new position, you can apply the

throttle again.

(1) Handle

(2) Locking lever

• Use only as much throttle as is

needed to do the job. Excessive

engine speed is unnecessary.

• Avoid cutting thick branches, for

which will damage the blades and

shorten the life of drive systems.

• Tilting the trimmer 5 to 10° to the

cutting object will make the job

easy and bring a good result.

• Always keep your body to the

carburetor side of your trimmer,

never on the muffler side.

• When a new machine is first

operated, in the first few minutes

grease may come out of the gear

case. But, since this is excess

grease, there is no cause for

alarm. Just wipe it off with the

engine stopped for next use.

Download from Www.Somanuals.com. All Manuals Search And Download.

F5 (eHT600D)

Download from Www.Somanuals.com. All Manuals Search And Download.

English

6. MAINTENANCE

WARNING

Before cleaning, inspecting, or

repairing the unit, make sure that

the engine has stopped and is

cool.

■ BLADE (F8)

• Check the blade and the fasteners

for looseness, cracking, or

bending.

• Check the cutting edges and

reform with a flat file.

Point:

1. Keep the end corner sharp.

2. Round the root of the edge.

3. Do not use water when using a

grinder.

■ You need not to adjust the gap

between upper blade and lower

blade as this product is

designed to have optimal gap

when it is properly set up. (F9)

(1) Bolt

(2) Washer

(3) Spacer

IMPORTANT

When mounting the blade, make sure

to fasten the spacer, washer and

bolt.

■ SAFETY LOCK (F10)

WARNING

F10

Stop operation when the safety

lock is defective.

Safety lock is the device not to

accelerate the throttle lever without

intention. While pushing the safety

lock, you can accelerate the throttle

lever.

(1) Safety lock

1. Check if the throttle lever does not

move when you do not push the

safety lock.

2. Check if the throttle lever moves

when you grasp or release it while

pushing the safety lock.

Download from Www.Somanuals.com. All Manuals Search And Download.

F10

Download from Www.Somanuals.com. All Manuals Search And Download.

English

6. MAINTENANCE

3. Check if the safety lock returns to

its original position when you

release your hand from safety

lock.

If you find any defects at the checks

above, contact your nearest servicing

dealer for repair.

F11

■ ANTI-VIBRATION SYSTEM (F11)

WARNING

The deformed or damaged anti-

vibration system may cause of the

breakages like getting rickety or

falling off of engine and/or blade.

• [eHT750S] Check periodically if

the rubber cushions are not

deformed or damaged.

• [eHT600D] Check periodically if

the springs are not deformed or

damaged.

F12

■ AIR CLEANER (F12)

Release the air cleaner cover and

remove dusts. In case the element is

dirty, carefully wash it with warm

water containing neutral detergent.

Completely dry before refitting the

element. If the element is deformed

or damaged, replace it with new one.

IMPORTANT

Clogged air cleaner spoils engine

performance. Also, operation with no

element or with deformed or

damaged element causes irregular

wear outs of the engine mechanism.

Download from Www.Somanuals.com. All Manuals Search And Download.

F11

F12

Download from Www.Somanuals.com. All Manuals Search And Download.

English

6. MAINTENANCE

■ FUEL FILTER (F13)

F13

When the engine runs short of fuel

supply, check the fuel strainer for

blockage.

■ WAY OF THE COOLING AIR

(F14)

F14

This engine is air-cooled. Dust

clogging between the inlet port of the

cooling air and cylinder fins will

cause overheating of the engine.

Periodically check and clean the

cylinder fins after removing the air

cleaner and the cylinder cover.

■ SPARK PLUG (F15)

Starting failure and mis-firing are

often caused by a fouled spark plug.

Periodically clean the spark plug, and

replace with a new one as required.

F15

IMPORTANT

When dismounting the plug cap, be

careful not to take off the seal from

the plug cap. Operating the engine

without seal may cause overheating

of the engine.

IMPORTANT

When setting up the spark plug,

screw it by your fingers at first, then

tighten by using special plug wrench.

Over tightening will damage the

cylinder and piston.

Tightening Torque:

15.3 ~ 22.4 N.m (150 ~ 220kgf-cm)

Type of Plug

Spark Gap

Champion CJ6Y

0.6 ~ 0.7 mm

Download from Www.Somanuals.com. All Manuals Search And Download.

F13

F14

F15

Download from Www.Somanuals.com. All Manuals Search And Download.

English

6. MAINTENANCE

■ GEARCASE (F16)

Supply multi-purpose grease at every

20 hours of use.

F16

1. Use a grease pump.

2. Feed grease until it comes out of

the base of blades.(F16-a)

■ ADJUSTING CARBURETOR

(F17)

F17

The carburetor has been adjusted at

the factory. Should your unit need

readjustment due to the changes in

altitude or operating conditions,

please let your skillful dealer make

the adjustment. A wrong adjustment

may cause damage to your unit.

(1) Idle adjusting screw

(2) Up

(3) Down

(4) Fuel adjusting screw

(Opening 1 1/4)

(5) Decrease

(6) Increase

■ THROTTLE WIRE PLAY (F18)

Throttle wire play should be 1~2 mm.

After completely returning the throttle

lever, take the throttle wire at the

carburetor end in your fingers and

give a light tug. If the play is too great

or too small, readjust the position of

the wire retaining nut. Loosen the

lock nut and turn the wire retaining

nut clockwise (screw in) to increase

the play and counter-clockwise

(unscrew) to reduce it. After

adjusting, please fasten the wire

retaining nut by tightening the lock

nut.

F18

a. Lock nut

b. Wire retaining nut

c. Wire sleeve

Download from Www.Somanuals.com. All Manuals Search And Download.

F16

F17

F18

Download from Www.Somanuals.com. All Manuals Search And Download.

English

6. MAINTENANCE

■ MUFFLER

AFTER 100 HOURS OF USE

1. Remove the muffler, insert a

screwdriver into the vent, and

wipe away any carbon buildup.

Wipe away any carbon buildup on

the muffler exhaust vent at the

same time. (F19)

F19

(1) screw driver

(2) muffler

2. Tighten all screws, bolts, and

fittings.

3. Check to see if any oil or grease

has worked its way in between the

clutch lining and drum, and if it

has wipe it away using oil-free,

lead-free gasoline.

■ MAINTENANCE

BEFORE

STORAGE

F20

IMPORTANT

Use a dry rag to wipe any fuel which

has been spilled onto the unit.

(F20)

1. Extract fuel from the tank and run

the engine until it stops naturally.

2. Remove the spark plug and put in

1~2 cc of 2-cycle oil in the engine.

Pull the starter rope 2~3 times, set

the plug back, and stop it at the

contraction position.

3. Apply anti-rust oil to the metal

parts such as the throttle wire etc.,

put the cover on the blade, and

keep it indoor avoiding dampness.

Download from Www.Somanuals.com. All Manuals Search And Download.

F19

F20

Download from Www.Somanuals.com. All Manuals Search And Download.

English

7. SPECIFICATIONS

Model name

.................. eHT750S [eHT600D]

Type

.......Single blade [Double-blade],

double-action type

Blade length

.............................. 750 [600]mm

Engine model

........................... Zenoah G20LH

Displacement

......................................... 21.7cc

Carburetor

.......................... Diaphragm type

Ignition system

........................................... C.D.I

Spark plug

......................... Champion CJ6Y

Fuel

........................................ Mixture

(Gasoline 25 : 2-cycle oil 1)

Fuel tank capacity

...................................... 0.4 litres

Starter

.............................. Recoil starter

Clutch

.......................... Centrifugal type

Reduction ratio

............................................ 4.78

Dry weight

.................................. 4.5 [4.4] kg

Specifications are subject to change

without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Working for a better tomorrow

Head Office:

1-9, Minamidai, Kawagoe-city, Saitama, 350-1192 Japan

Telephone: (+81)492-43-1117 Telecopier: (+81)492-43-7197

PRINTED IN JAPAN

Download from Www.Somanuals.com. All Manuals Search And Download.

Weslo Treadmill WETL149051 User Manual
Westinghouse Cell Phone LD 268 SERIES User Manual
Whirlpool Cooktop CEX200V User Manual
Whistler GPS Receiver GLF 125 User Manual
White Outdoor Snow Blower 772C0715 User Manual
Yamaha Jet Ski F1W F8199 10 User Manual
Zanussi Freezer 110 W User Manual
Zanussi Freezer ZRD 185W1 User Manual
Zanussi Range ZKG5020 User Manual
Zenoah Brush Cutter BC3400FW User Manual