OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
CHAPTER 1 Using the Robot Safely
1 Safety Information ..................................................................1-1
2 Essential Caution Items ..........................................................1-2
3 Special Training for Industrial Robot Operation ......................1-9
4 Robot Safety Functions ........................................................1-10
5 Safety Measures for the System .......................................... 1-11
6 Trial Run ...............................................................................1-12
7 Work Within the Safeguard Enclosure..................................1-13
8 Automatic Operation .............................................................1-14
9 Adjustment and Inspection ...................................................1-14
10 Repair and Modification ........................................................1-14
11 Warranty ...............................................................................1-15
12 CE Marking ...........................................................................1-16
CHAPTER 2 Product Outline
1 Robot ......................................................................................2-1
2 Names of each part ................................................................2-2
3 Robot Controller .....................................................................2-7
CHAPTER 3 Preparing the Robot
1 Robot Installation Environment...............................................3-1
2 Unpacking the Robot ..............................................................3-2
3 Checking the Product .............................................................3-3
4 Transporting the Robot ...........................................................3-5
5 Installation ..............................................................................3-7
5-1 Installation base ............................................................................... 3-7
5-2 Installing the Robot .......................................................................... 3-8
6 Protective connections ...........................................................3-9
7 Connecting the Robot Cables...............................................3-10
7-1 Connecting with the DRCX controller ............................................ 3-12
7-2 Connecting with the TRCX controller ............................................. 3-14
7-2-1 3-axis model ..................................................................................3-14
7-2-2 4-axis model ..................................................................................3-16
7-3 Connecting to the QRCX or RCX40 controller............................... 3-18
8 Installing the Tool ..................................................................3-20
9 User Wiring and User Piping ................................................3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Setting the Robot ..................................................................3-22
10-1 Setting the payload ........................................................................ 3-22
10-2 Setting the maximum speed .......................................................... 3-23
10-3 Setting the acceleration ................................................................. 3-24
11 Absolute Reset .....................................................................3-25
CHAPTER 4 Periodic Inspections
1 Outline ....................................................................................4-1
2 Precautions.............................................................................4-1
3 Daily inspection ......................................................................4-2
4 Three-month inspection ..........................................................4-2
5 Six-month inspection ..............................................................4-3
6 Three-year inspection .............................................................4-4
7 Replenishing the grease .........................................................4-5
8 Maintenance and inspection of harmonic drives ....................4-6
8-1 Harmonic grease replacement period.............................................. 4-7
CHAPTER 5 Specifications
1 Specifications .........................................................................5-1
1-1 Robot cable...................................................................................... 5-1
1-2 User I/O cable .................................................................................. 5-5
CHAPTER 6 PXYX
1 Installation ..............................................................................6-1
1-1 Installation bolt types ....................................................................... 6-1
1-2 Installation bolt nominal length......................................................... 6-1
1-3 Tightening torque ............................................................................. 6-1
1-4 Installation methods ......................................................................... 6-2
2 Protective Connections...........................................................6-3
2-1 Ground terminal ............................................................................... 6-3
2-2 Ground wire ..................................................................................... 6-4
2-3 Wiring method.................................................................................. 6-4
3 Installing the Tool ....................................................................6-5
4 User Wiring and User Piping ..................................................6-6
5 Periodic Inspections ...............................................................6-8
5-1 Replenishing grease to the linear guide........................................... 6-8
5-2 Replenishing grease to the ball screw ............................................. 6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 7 FXYX
1 Installation ..............................................................................7-1
1-1 Installation bolt types ....................................................................... 7-1
1-2 Installation bolt nominal length......................................................... 7-1
1-3 Tightening torque ............................................................................. 7-1
1-4 Installation methods ......................................................................... 7-2
2 Protective Connections...........................................................7-3
2-1 Ground terminal ............................................................................... 7-3
2-2 Ground wire ..................................................................................... 7-4
2-3 Wiring method.................................................................................. 7-4
3 Installing the Tool ....................................................................7-5
3-1 Arm type 2-axis model ..................................................................... 7-5
3-2 ZS (3rd-axis option) ......................................................................... 7-7
4 User Wiring and User Piping ..................................................7-8
4-1 Cable carrier type............................................................................. 7-8
4-1-1 Example of wiring and piping methods using cable carrier .............7-8
4-1-2 Cable carrier specifications ........................................................... 7-11
4-1-3 User I/O cable specifications .........................................................7-12
5 Periodic Inspections .............................................................7-13
5-1 Replenishing grease to the linear guide......................................... 7-13
5-2 Replenishing grease to the ball screw ........................................... 7-14
CHAPTER 8 SXYX
1 Installation ..............................................................................8-1
1-1 Installation bolt types ....................................................................... 8-1
1-2 Installation bolt nominal length......................................................... 8-1
1-3 Tightening torque ............................................................................. 8-2
1-4 Installation methods ......................................................................... 8-2
2 Protective Connections...........................................................8-5
2-1 Ground terminal ............................................................................... 8-5
2-2 Ground wire ..................................................................................... 8-6
2-3 Wiring methods ................................................................................ 8-6
2-3-1 Arm type with cable carrier ..............................................................8-7
2-3-2 Arm type with whipover cable, moving arm type, pole type ............8-9
2-3-3 XZ type ..........................................................................................8-10
3 Installing the Tool .................................................................. 8-11
3-1 Arm type, pole type 2-axis model....................................................8-11
3-2 Moving arm type 2-axis model ....................................................... 8-13
3-3 ZF
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ......... 8-14
3-4 RF
(Arm type, moving arm type, 4th-axis option/XZ type 3rd-axis option) ..... 8-15
3-5 ZS/ZRS (Arm type 3/4-axis option, XZ type 2/3-axis model) ......... 8-16
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6 ZFH (Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option ......................................................................... 8-17
3-7 ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 8-18
4 User Wiring and User Piping ................................................8-19
4-1 Cable carrier type........................................................................... 8-19
4-1-1 Example of wiring and piping methods using cable carrier ...........8-19
4-1-2 Cable carrier specifications ...........................................................8-22
4-1-3 User I/O cable specifications .........................................................8-23
4-2 Whipover cable type ...................................................................... 8-24
4-2-1 Examples of wiring and piping with whipover cable ......................8-24
5 Periodic inspections..............................................................8-26
5-1 Replenishing grease to the linear guide......................................... 8-26
5-2 Replenishing grease to the ball screw ........................................... 8-27
5-3 Periodic inspection of the ZS/ZRS unit .......................................... 8-29
5-3-1 Replenishing grease to the Z-axis ball screw and ball spline ........8-29
5-3-2 Adjusting the R-axis belt tension (ZRS) ........................................8-30
5-3-3 Replacing the R-axis harmonic drive (ZRS) ..................................8-31
CHAPTER 9 MXYX
1 Installation ..............................................................................9-1
1-1 Installation bolt types ....................................................................... 9-1
1-2 Installation bolt nominal length......................................................... 9-1
1-3 Tightening torque ............................................................................. 9-1
1-4 Installation methods
(Arm type, moving arm type, pole type, gantry type X-axis) ............ 9-2
1-5 Installation methods (Gantry type support axis)............................... 9-4
2 Protective Connections...........................................................9-5
2-1 Ground terminal ............................................................................... 9-5
2-2 Ground wire ..................................................................................... 9-5
2-3 Wiring methods ................................................................................ 9-6
3 Installing the Tool ....................................................................9-7
3-1 Arm type, pole type 2-axis model..................................................... 9-7
3-2 Moving arm type 2-axis model ......................................................... 9-9
3-3 ZF
(Arm type, moving arm type, gantry type 3rd-axis option) ............. 9-10
3-4 RF
(Arm type, moving arm type, 4th-axis option/XZ type 3rd-axis option) ... 9-11
3-5 ZFH (Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option ......................................................................... 9-12
3-6 ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 9-13
Download from Www.Somanuals.com. All Manuals Search And Download.
4 User Wiring and User Piping ................................................9-14
4-1 Cable carrier type........................................................................... 9-14
4-1-1 Example of wiring and piping methods using cable carrier ...........9-14
4-1-2 Cable carrier specifications ...........................................................9-17
4-1-3 User I/O cable specifications .........................................................9-18
4-2 Whipover cable type ...................................................................... 9-19
4-2-1 Examples of wiring and piping with Whipover cable .....................9-19
5 Periodic Inspections .............................................................9-21
5-1 Replenishing grease to the linear guide......................................... 9-21
5-2 Replenishing grease to the ball screw ........................................... 9-22
CHAPTER 10 HXYX
1 Installation ............................................................................10-1
1-1 Installation method 1
(Arm type, moving arm type, pole type, gantry type X-axis) .......... 10-1
1-1-1 Installation bolt types .....................................................................10-1
1-1-2 Installation bolt nominal length ......................................................10-1
1-1-3 Tightening torque...........................................................................10-2
1-1-4 Installation methods ......................................................................10-2
1-2 Installation method 2 (XZ type) ...................................................... 10-4
1-2-1 Installation bolt ..............................................................................10-4
1-2-2 Installation bolt nominal length ......................................................10-4
1-2-3 Tightening torque...........................................................................10-5
1-2-4 Installation methods ......................................................................10-5
1-3 Installation method 3 (Gantry type support axis) ........................... 10-6
2 Protective Connections.........................................................10-7
2-1 Ground terminal ............................................................................. 10-7
2-2 Ground wire ................................................................................... 10-8
2-3 Wiring methods .............................................................................. 10-8
3 Installing the Tool ................................................................10-10
3-1 Arm type, gantry type 2-axis model ..............................................10-11
3-2 Moving arm type 2-axis model ..................................................... 10-12
3-3 Pole type 2-axis model................................................................. 10-13
3-4 ZH
(Arm type, gantry type, moving arm type 3rd-axis option/XZ type 2-axis model) .... 10-14
3-5 ZL
(Arm type, gantry type, moving arm type 3rd-axis option/XZ type 2-axis model) .... 10-15
3-6 ZPH (Pole type 3rd-axis option)................................................... 10-16
3-7 RH
(Arm type, moving arm type, gantry type 4th-axis option/XZ type 3rd-axis option) ..... 10-17
4 User Wiring and User Piping ..............................................10-18
4-1 Cable carrier type......................................................................... 10-18
4-1-1 Example of wiring and piping methods using cable carrier .........10-18
4-1-2 Cable carrier specifications .........................................................10-20
4-1-3 User I/O cable specifications .......................................................10-21
4-2 Whipover cable type .................................................................... 10-22
4-2-1 Examples of wiring and piping with Whipover cable ...................10-22
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Periodic Inspections ...........................................................10-24
5-1 Replenishing grease to the linear guide....................................... 10-24
5-2 Replenishing grease to the ball screw ......................................... 10-25
CHAPTER 11 FXYBX/SXYBX
1 Installation ............................................................................ 11-1
1-1 Installation bolt types ......................................................................11-1
1-2 Installation bolt nominal length........................................................11-1
1-3 Tightening torque ............................................................................11-2
1-4 Installation methods ........................................................................11-2
2 Protective connections ......................................................... 11-3
2-1 Ground terminal ..............................................................................11-3
2-2 Ground wire ....................................................................................11-4
2-3 Wiring methods (Cable carrier type) ...............................................11-4
2-4 Wiring methods (Whipover cable type) ...........................................11-6
3 Installing the Tool .................................................................. 11-7
3-1 FXYBX arm type 2-axis model........................................................11-7
3-2 SXYBX arm type 2-axis model........................................................11-8
3-3 SXYBX-ZF (XZ type 2-axis, arm type 3rd-axis option) ...................11-9
3-4 ZS/ZRS (FXYBX, SXYBX 3/4-axis option)....................................11-10
3-5 ZFH (Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option ........................................................................ 11-11
3-6 ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 11-12
4 User Wiring and User Piping .............................................. 11-13
4-1 Cable carrier type..........................................................................11-13
4-1-1 Example of wiring and piping methods using cable carrier ......... 11-13
4-1-2 Cable carrier specifications ......................................................... 11-15
4-1-3 User I/O cable specifications ....................................................... 11-16
4-2 Whipover cable type .....................................................................11-16
4-2-1 Examples of wiring and piping with Whipover cable ................... 11-17
5 Changing the Motor Installation Position ............................ 11-19
5-1 Changing the motor installation position .......................................11-19
6 Installing the Cover .............................................................11-21
7 Adjusting the Timing Belt Tension....................................... 11-22
7-1 Adjusting the drive belt tension .....................................................11-23
7-2 Adjusting the speed reduction belt tension ...................................11-25
8 Periodic inspections............................................................ 11-27
8-1 Replacing the motor......................................................................11-27
8-2 Replacing the drive belt ................................................................11-28
8-3 Replacing the speed reduction belt...............................................11-31
8-4 Replacing the slider ......................................................................11-32
8-5 Replenishing the grease ...............................................................11-33
8-5-1 Replenishing grease to the linear guide ...................................... 11-33
8-5-2 Replenishing grease to the ball screw (ZF) ................................. 11-35
Download from Www.Somanuals.com. All Manuals Search And Download.
8-6 Periodic inspection of the ZS/ZRS unit .........................................11-36
8-6-1 Replenishing grease to the Z-axis ball screw and ball spline ...... 11-36
8-6-2 Adjusting the R-axis belt tension (ZRS) ...................................... 11-37
8-6-3 Replacing the R-axis harmonic drive (ZRS) ................................ 11-38
CHAPTER 12 HXYLX
1 Installation ............................................................................12-1
1-1 Installation method 1
(Arm type, moving arm type, pole type, gantry type X-axis) .......... 12-1
1-1-1 Installation bolt types .....................................................................12-1
1-1-2 Installation bolt nominal length ......................................................12-1
1-1-3 Tightening torque...........................................................................12-2
1-1-4 Installation methods ......................................................................12-2
1-2 Installation method 3 (Gantry type support axis) ........................... 12-5
2 Protective Connections.........................................................12-6
2-1 Ground terminal ............................................................................. 12-6
2-2 Ground wire ................................................................................... 12-7
2-3 Wiring methods .............................................................................. 12-7
3 Installing the Tool ..................................................................12-8
3-1 Arm type, gantry type 2-axis model ............................................... 12-8
3-2 Moving arm type 2-axis model ....................................................... 12-9
3-3 Pole type 2-axis model................................................................. 12-10
3-4 ZH
(Arm type, gantry type, moving arm type 3rd-axis option) ............12-11
3-5 ZL (Arm type, gantry type) ........................................................... 12-12
3-6 ZPH (Pole type 3rd-axis option)................................................... 12-13
3-7 RH (Arm type, gantry type 4th-axis option).................................. 12-14
4 User Wiring and User Piping ..............................................12-15
4-1 Cable carrier type......................................................................... 12-15
4-1-1 Example of wiring and piping methods using cable carrier .........12-15
4-1-2 Cable carrier specifications .........................................................12-17
4-1-3 User I/O cable specifications .......................................................12-18
4-2 Whipover cable type (moving arm type/pole type 3-axis) ............ 12-19
4-2-1 Examples of wiring and piping with Whipover cable ...................12-19
5 Periodic Inspections ...........................................................12-21
5-1 Replenishing grease to the linear guide....................................... 12-21
5-2 Replenishing grease to the ball screw ......................................... 12-22
5-3 Adjusting the timing belt tension (X-axis)..................................... 12-24
5-4 Replacing the motor (X-axis) ....................................................... 12-25
5-5 Installing and removing the cover ................................................ 12-27
5-5-1 Stroke cover ................................................................................12-27
5-5-2 Belt cover ....................................................................................12-28
5-5-3 Motor cover .................................................................................12-29
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Using the Robot Safely
1 Safety Information ..................................................................1-1
2 Essential Caution Items ..........................................................1-2
3 Special Training for Industrial Robot Operation ......................1-9
4 Robot Safety Functions ........................................................1-10
5 Safety Measures for the System .......................................... 1-11
6 Trial Run ...............................................................................1-12
7 Work Within the Safeguard Enclosure..................................1-13
8 Automatic Operation .............................................................1-14
9 Adjustment and Inspection ...................................................1-14
10 Repair and Modification ........................................................1-14
11 Warranty ...............................................................................1-15
12 CE Marking ...........................................................................1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
1
Safety Information
Industrial robots are highly programmable machines that provide a large degree
of freedom in movement. To ensure correct and safe use of YAMAHA robots,
carefully read this manual to make yourself well acquainted with the contents.
FOLLOW THE WARNINGS, CAUTIONSAND INSTRUCTIONS INCLUDED
IN THIS MANUAL. Failure to take necessary safety measures or mishandling
due to not observing the instructions in this manual may result in trouble or dam-
age to the robot and injury to personnel (robot installer, operator or service per-
sonnel) including fatal accidents.
Warning information in this manual is classified into the following items.
DANGER
Failure to follow DANGER instructions will result in severe injury or death
to the robot operator, bystanders or persons servicing the robot.
WARNING
Failure to follow WARNING instructions could result in severe injury or
death to the robot operator, bystanders or persons servicing the robot.
!
CAUTION
Failure to follow CAUTION instructions may result in injury to the robot opera-
tor, bystanders or persons servicing the robot, or damage to the robot and/or
robot controller.
NOTE
Explains the keypoint in the operation in a simple and clear manner.
Refer to the instruction manual by any of the following methods to operate or
adjust the robot safely and correctly.
1. Operate or adjust the robot while referring to the printed version of the in-
struction manual (available for an additional fee).
2. Operate or adjust the robot while viewing the CD-ROM version of the in-
struction manual on your computer screen.
3. Operate or adjust the robot while referring to a printout of the necessary
pages from the CD-ROM version of the instruction manual.
It is not possible to list all safety items in detail within the limited space of this
manual. Thus, it is essential that the user have full knowledge of basic safety
rules and that the operator makes correct judgments on safety procedures during
operation.
When exporting this robot, the warning labels and instruction manuals must be
changed to export specifications.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
2
Essential Caution Items
Particularly important cautions for handling or operating the robot are described
below. In addition, safety information about installation, operation, inspection
and maintenance is provided in each chapter. Be sure to comply with these in-
structions to ensure safe use of the robot.
(1) Observe the following cautions during automatic operation
DANGER
Serious injury will result from impact with moving robot.
• Keep outside safeguard enclosure during automatic operation.
• Press the emergency stop button before entering the safeguard enclo-
sure.
The warning label 1 (Fig. 1-1) is attached to the robot.
• Install a safeguard enclosure to keep all personnel from entering within the
movable range of the robot and suffering injury due to being struck by
moving parts.
• Install a safety interlock that triggers emergency stop when the door or
panel is opened.
• Install safeguards so that no one can enter inside except from doors or
panels equipped with safety interlocks.
• The warning label 1 (Fig. 1-1) are supplied with the robot and should be
affixed to conspicuous places on doors or panels equipped with safety in-
terlocks.
(2) Use caution to prevent hands or fingers from being pinched or
crushed.
WARNING
Moving parts can pinch or crush.
Keep hands always from robot arms.
Warning label 2 (Fig. 1-2) is affixed to the robot.
Use caution to prevent hands or fingers from being pinched or crushed in the
robot’s moving parts during transporting the robot or teaching, etc.
DANGER
WARNING
Serious injury or death
will result from impact
Moving parts can
pinch or crush.
with moving robot.
• Keep outside of guard
during operation.
• Lock out power before
approaching robot.
Keep hands away
from robot arms.
Fig. 1-1 Warning label 1
Fig. 1-2 Warning label 2
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
(3) Follow the instructions listed on warning labels and in this
manual.
WARNING
Improper installation or operation can result in serious injury. Read the
Instruction Manual and all warning labels before operation.
The warning label 3 (Fig. 1-3) is attached to the robot.
• Be sure to read the warning labels and this manual carefully and make sure
to thoroughly understand the contents before attempting installation and
operation of the robot.
• Before starting robot operation, be sure to reread the procedures and cau-
tions related to the work as well as the descriptions in this chapter (Chapter
1. “Using the Robot Safely”).
• Never install, adjust, inspect, service or operate the robot in any manner
that does not comply with the instructions in this manual.
WARNING
Improper Installation or operation
can result in serious injury or
death.
Read owner's manual and all
warning labels before operation.
Fig. 1-3 Warning label 3
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
(4) Do not use the robot in environments containing inflammable
gas, etc.
WARNING
• This robot is not designed for operation in environments where inflam-
mable of explosive substances are present.
•
Do not use the robot in environments containing inflammable gas,
dust or liquids.
Explosions or fire might otherwise result.
(5) Do not use the robot in locations possible subject to electro-
magnetic interference, etc.
WARNING
Avoid using the robot in locations subject to electromagnetic interfer-
ence, electrostatic discharge or radio frequency interference.
Malfunctions might otherwise occur.
(6) Use caution when releasing the brake for the Z-axis (vertical axis).
WARNING
The Z-axis will drop when the brake is released, creating a hazardous
situation.
• Press the emergency stop button and prop up the Z-axis with a support
stand, etc., before releasing the brake.
• Be careful not to let your body get caught between the Z-axis and in-
stallation base, etc., when releasing the brake to perform direct teach-
ing.
(7) Provide safety measures for end effector (gripper, etc.)
WARNING
• End effectors must be designed and manufactured so that they create
no hazards (for example, a workpiece that comes loose) even if power
(electricity, air pressure, etc.) is shut off or a power fluctuation occurs.
• If there is a possible danger that the object gripped by the end effector
may fly off or drop, then provide appropriate safety protection taking
into account the object size, weight, temperature and chemical proper-
ties.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
(8) Movement of Z-axis at controller power shut off and emergency
stop (for ZAS)
WARNING
The Z-axis will start to rise when the controller power is shut off, the PLC
power is shut off, the program is reset, emergency stop is applied, and
when the supply of air to the Z-axis air cylinder’s solenoid valve is started.
• Take care not to pinch or crush hands, etc., in the Z-axis moving sec-
tions.
• If there are any interferences in the Z-axis' upward travel path, reevaluate
the robot position, except for emergencies.
(9) Pay attention to interference of Z-axis with peripheral devices
(for ZAS)
WARNING
If the Z-axis interferes with a peripheral device and stops, there is a risk of
pinching hands, etc., when the interfering object is removed as the Z-axis
will suddenly move.
• Turn the controller power OFF and stop the air supply before removing
the interfering object.
• The Z-axis will naturally drop, so prop it up with a support stand, etc.,
before stopping the air supply.
(10)Z-axis movement when air supply is stopped
WARNING
The Z-axis will drop when the air supply is stopped, creating a hazardous
situation.
Prop up the Z-axis with a support stand, etc., before turning the controller
power OFF and stopping the air supply.
(11) Use caution when disassembling and replacing the pneumatic
devices
WARNING
If the pneumatic devices are disassembled or replaced while the air is
supplied, the parts or air could scatter.
• Turn the controller power OFF, stop the air supply and release all re-
sidual pressure from the pneumatic devices before starting work.
• The Z-axis will naturally drop, so prop it up with a support stand, etc.,
before stopping the air supply.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
(12)Use caution when disassembling and replacing the motor
WARNING
When disassembling or assembling the motor for a ball-screw drive type
robot, a strong magnetic attraction force will be present between the motor
stator (fixed coil) and rotor (rotating magnet), causing a risk of pinching
hands, etc.
A YAMAHA-trained operator must carry out this work using the YAMAHA-
recommended jigs.
(13)Use caution when removing the Z-axis brake
WARNING
The Z-axis will naturally drop when the brake is removed, causing a haz-
ardous situation.
• Prop up the Z-axis with a support stand, etc., before turning the control
power OFF and removing the brake.
• Be careful not to let your body get caught between the Z-axis drive
section and Z-axis installation base, etc.
(14)Take the following safety precautions during inspection of the
controller
WARNING
• If the terminals or connectors on the outside of the controller must be
touched during inspection, etc., always first turn the controller power
OFF and the power source to prevent possible electrical shock.
• Refer to the "YAMAHA Robot Controller Instruction Manual" for pre-
cautions on handling the controller. Never touch any internal parts of
the controller.
(15)Consult YAMAHA for corrective action when the robot is dam-
aged or malfunctions occur.
WARNING
If any part of the robot is damaged or any malfunction occurs, continuing
the operation may be very dangerous. Please consult your YAMAHA sales
office or dealer for corrective action.
Damage or Trouble
Damage to machine harness or robot cable
Damage to exterior of robot
Possible Danger
Electrical shock, malfunction of robot
Flying outward of damaged parts during
robot operation
Abnormal operation of robot (positioning error,
excessive vibration, etc.)
Malfunction of robot
Dropping of load
Z-axis brake trouble
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
(16)Use caution not to touch the controller rear panel cooling fan
WARNING
• Injury may occur from coming into contact with the cooling fan while it
is rotating.
• When removing the fan cover for inspection, first turn OFF the control-
ler and make sure that the fan has stopped.
(17)Be careful not to touch the motor or speed reduction gear cas-
ing when hot.
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched.
• Before handling these parts during inspection or servicing, turn the
controller power OFF, wait for a while and check that the part has cooled.
(18)Do not remove, alter or stain the warning labels
WARNING
If the warning labels are removed or difficult to see, then essential pre-
cautions might not be taken resulting in accidents.
• Do not remove, alter or stain the warning labels on the robot.
• Do not allow the warning labels to be hidden by devices installed onto
the robot by the user.
• Provide proper lighting so that the symbols and instructions on the
warning labels can be clearly seen even from outside the safeguard
enclosure.
(19)Protective connections
WARNING
Be sure to ground the robot and controller to prevent electrical shock.
(20)Be sure to make correct parameter settings - Part 1
!
CAUTION
Always input the correct parameters matching the payload and stroke (working
envelope) before operating the robot.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
(21)Be sure to make correct parameter settings - Part 2
!
CAUTION
When using a rotary axis (RF, RH, etc.) the robot must be operated with the
tolerable moment of inertia and correct acceleration coefficients according to
the tip mass and moment of inertia. If these are not correct, the drive unit serv-
ice life may end prematurely, and damage to robot parts or residual vibration
during positioning may result.
(22) Do not use the robot for tasks requiring motor thrust.
!
CAUTION
Avoid using the belt-driven type robots for tasks that utilize motor thrust (press
fitting, burr removal, etc.).
These tasks may cause malfunctions in the robot.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
3
Special Training for Industrial Robot Operation
Companies or factories using industrial robots must make sure that every person,
who handles the robot such as for teaching, programming, movement check, in-
spection, adjustment and repair, has received appropriate training and also has
the skills needed to perform the job correctly and safely.
SinceYAMAHA Cartesian Robot XY Series falls under the industrial robot cat-
egory, the user must observe local regulations and safety standards for industrial
robots, and provide special training for every person involved in robot-related
tasks (teaching, programming, movement check, inspection, adjustment, repair,
etc.).
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
4
Robot Safety Functions
(1) Overload detection
This function detects an overload applied to the motor and shuts off the servo
power.
(2) Overheat detection
This detects an abnormal rise in the controller driver temperature and shuts
off the servo power.
If an overload or overheat error occurs, take the following measuring.
1. Insert a timer in the program.
2. Reduce the acceleration coefficient.
(3) Soft limits
Soft limits can be set on each axis to limit the working envelope in manual
operation after return-to-origin and during automatic operation. Note that
the working envelope is the area limited by soft limits.
(4) Mechanical stoppers
If the servo power is suddenly shut off during high-speed operation by emer-
gency stop or safety functions, these mechanical stoppers prevent the axis
from exceeding the movable range.
No mechanical stopper is provided on the R-axis.
Note that the movable range is the area limited by the mechanical stoppers.
(5) Z-axis (vertical axis) brake
An electromagnetic brake is installed on the Z-axis to prevent the Z-axis
from dropping when the servo power is shut off. This brake is working when
the controller power is OFF or if the Z-axis servo is OFF even when the
controller power is ON.
The Z-axis brake can be released by means of the programming unit or by a
command in the program when the controller power is ON.
WARNING
The Z-axis will drop when the brakes are released, creating a hazardous
situation.
• Press the emergency stop button and prop up the Z-axis with a support
stand, etc., before releasing the brake.
• Be careful not to let your body get caught between the Z-axis and in-
stallation base, etc., when releasing the brake to perform direct teach-
ing.
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
5
Safety Measures for the System
When the robot is commonly used in conjunction with an automated system,
dangerous situations are more likely to occur from the automated system than
from the robot itself. Appropriate safety measures must be taken on the part of
the system manufacturer according to the individual system.
The system manufacture should provide a proper instruction manual for safe,
correct operation and servicing of the system.
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
6
Trial Run
After making installations, adjustments, inspections, maintenance or repairs to
the robot, carry out trial run using the following procedures.
(1) If a safeguard enclosure has not yet been provided right after installa-
tion of the robot, rope off or chain off the movable range in place of
the safeguard enclosure, and observe the following points.
1. Use sturdy, stable posts that will not fall over easily.
2. The rope or chain should be easily visible by everyone around the robot.
3. Place a sign to keep the operator or other personnel from entering the
movable range.
(2) Check the following points before turning the controller ON.
1. Is the robot securely and correctly installed?
2. Are the electrical connections to the robot correct?
3. Are items such as air pressure correctly supplied?
4. Is the robot correctly connected to peripheral devices?
5. Have safety measures (safeguard enclosure, etc.) been taken?
6. Does the installation environment meet the specified standards?
(3) After the controller power is turned ON, check the following points
from outside the safeguard enclosure.
1. Does the robot start and stop as intended? Can the operation mode be
selected correctly?
2. Does each axis move as intended within the soft limits?
3. Does the end effector move as intended?
4. Are the signal transmissions to the end effector and peripheral devices
correct?
5. Does emergency stop work?
6. Are the teaching and playback functions normal?
7. Are the safeguard enclosure and interlock working as intended?
8. Does the robot move correctly during automatic operation?
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
7
Work Within the Safeguard Enclosure
(1) When work is required in the safeguard enclosure, always turn the
controller power OFF and place a sign indicating that the robot is
being adjusted or serviced in order to keep any other personnel from
touching the controller power switch or operation panel, except for
the following cases.
1) Soft limit settings
2) Teaching
For item 1), follow the precautions and procedure for each section.
To perform item 2), refer to the description in (2) below.
(2) Teaching
When performing teaching within the safeguard enclosure, comply with the
instructions listed below.
1) Check or perform the following points from outside the safeguard enclo-
sure.
1. Make sure that no hazards are present within the safeguard enclosure
by a visual check.
2. Check that the programming unit MPB or TPB operates correctly.
3. Check that no failures are found in the robot.
4. Check that emergency stop works correctly.
5. Select teaching mode and prohibit automatic operation.
2) Never enter the movable range of the robot while within the safeguard
enclosure.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
8
Automatic Operation
(1) Check the following before starting automatic operation.
1. No one is within the safeguard enclosure.
2. The programming unit or tools, etc., are in their specified location.
3. The alarm or error lamps, etc., on the robot and peripheral devices do not
flash.
4. The safeguard enclosure is securely installed with safety interlocks, etc.,
actuated.
(2) Observe the following during automatic operation or in cases where
an error occurs.
1) After automatic operation has started, check the operation status and warn-
ing lamps to ensure that the robot is in automatic operation.
2) Never enter the safeguard enclosure during automatic operation.
3) If an error occurs in the robot or peripheral devices, observe the following
procedures before entering the safeguard enclosure.
1. Press the emergency stop button to set the robot to emergency stop.
2. Place a sign on the start switch indicating that the robot is being in-
spected in order to keep any other person from touching the start switch
and restarting the robot.
9
Adjustment and Inspection
WARNING
Do not attempt any installation, adjustment, inspection or maintenance
unless described in this manual. Unexpected accidents or troubles may
otherwise result.
10
Repair and Modification
WARNING
Do not attempt any repair, part replacement or modification unless de-
scribed in this manual. These matters require technical knowledge and
skills, and may also involve work hazards.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
11
Warranty
The YAMAHA robot and/or related product you have purchased are warranted
against the defects or malfunctions as described below.
Warranty description
: If a failure or breakdown occurs due to defects
in materials or workmanship in the genuine parts
constituting thisYAMAHA robot and/or related
product within the warranty period, then
YAMAHA will repair or replace those parts free
of charge (hereafter called "warranty repair").
Warranty Period
:The warranty period ends when any of the fol-
lowing applies:
1) After 18 months (one and a half year) have
elapsed from the date of shipment
2) After one year has elapsed from the date of
installation
3) After 2,400 hours of operation
Exceptions to the Warranty : This warranty will not apply in the following
cases
1) Fatigue arising due to the passage of time,
natural wear and tear occurring during op-
eration (natural fading of painted or plated
surfaces, deterioration of parts subject to
wear, etc.)
2) Minor natural phenomena that do not affect
the capabilities of the robot and/or related
product (noise from computers, motors, etc.).
3) Programs, point data and other internal data
that were changed or created by the user.
Failures resulting from the following causes are not covered by warranty repair.
1) Damage due to earthquakes, storms, floods, thunderbolt, fire or any other
natural or man-made disasters.
2) Troubles caused by procedures prohibited in this manual.
3) Modifications to the robot and/or related product not approved by
YAMAHA or YAMAHA sales representatives.
4) Use of any other than genuine parts and specified grease and lubricants.
5) Incorrect or inadequate maintenance and inspection.
6) Repairs by other than authorized dealers.
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Using the Robot Safely
YAMAHA MOTOR CO., LTD. MAKES NO OTHER EXPRESS OR IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
THE WARRANTY SET FORTH ABOVE IS EXCLUSIVE AND IS IN LIEU
OFALL EXPRESSED OR IMPLIED WARRANTIES, INCLUDINGWARRAN-
TIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
OR WARRANTIES ARISING FROM A COURSE OF DEALING OR USAGE
OF TRADE.
YAMAHA MOTOR CO., LTD. SOLE LIABILITY SHALL BE FOR THE DE-
LIVERY OF THE EQUIPMENT ANDYAMAHA MOTOR CO., LTD. SHALL
NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES (WHETHER
ARISING FROM CONTRACT, WARRANTY, NEGLIGENCE OR STRICT
LIABILITY).YAMAHA MOTOR CO., LTD. MAKES NOWARRANTYWHAT-
SOEVER WITH REGARD TO ACCESSORIES OR PARTS NOT SUPPLIED
BY YAMAHA MOTOR CO., LTD.
12
CE Marking
Refer to the following YAMAHA Robot Controller Instruction Manuals for de-
tails on the related CE Marking for export to or use in EU regions.
• QRCX-E Instruction Manual
• ERCX/SRCX/DRCX compatible with CE marking supplement manual
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Product Outline
1 Robot ......................................................................................2-1
2 Names of each part ................................................................2-2
3 Robot Controller .....................................................................2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
1
Robot
The robot is configured of the standard function X/Y axes (horizontal cartesian
slide) and optional function Z-axis (vertical slide) and R-axis (rotation).
These configuration axes can move in the following manner. High-accuracy and
high-speed work can be carried out over a wide range by installing work tools.
(+) and (-) indicate the jog key movement directions. (Default settings)
Y-axis arm movement
(-)
(+)
(-)
(-)
(+)
X-axis arm movement
Z-axis (vertical)
(+)
(-)
(+)
R-axis (rotation)
Robot movements (with ZR axes)
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
2
Names of each part
■ Arm type with cable carrier
Y-axis
Y-axis stroke cover
Frame bracket
Y-axis motor
X-axis stroke cover
X-axis
X-axis motor
Robot cable
Y-axis slider (tool installation section)
Cable carrier between XY
(The machine harness between XY
is wired inside)
Y-axis wiring box
X-axis slider
X-axis wiring box
■ Arm type with whipover cable
Y-axis
Y-axis stroke cover
Frame bracket
X-axis motor
Y-axis motor
X-axis stroke cover
X-axis
Robot cable
whipover cable between XY
Y-axis slider
(tool installation section)
Y-axis wiring box
X-axis wiring box
X-axis slider
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
■ Gantry type
Support axis
Support axis
installation bracket
Y-axis
Y-axis stroke cover
Y-axis motor
X-axis stroke cover
X-axis
X-axis motor
Robot cable
Cable carrier between XY
(The machine harness between XY
is wired inside)
Y-axis slider (tool installation section)
Y-axis wiring box
Frame bracket
X-axis slider
X-axis wiring box
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
■ Moving arm type (with cable carrier)
Y-axis whipover cable
Y-axis bracket
Y-axis wiring box
Cable carrier between XY
(The machine harness between XY is wired inside)
Y-axis wiring box
(tool installation section)
X-axis stroke cover
X-axis
Y-axis
Y-axis stroke cover
X-axis slider
Y-axis motor
X-axis wiring box
X-axis motor
■ Moving arm type (with whipover cable)
whipover cable
between XY
Y-axis wiring box
Y-axis bracket
(tool installation section)
X-axis stroke cover
X-axis
X-axis slider
X-axis wiring box
Y-axis
Y-axis stroke cover
X-axis motor
Y-axis motor
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
■
Pole-type with cable carrier
Y-axis motor
Y-axis relay harness
Y-axis
Y-axis wiring box
Y-axis slider
(tool installation section)
Cable carrier between XY
(The machine harness between XY is wired inside)
Y-axis stroke cover
X-axis stroke cover
X-axis
Robot cable
X-axis slider
X-axis wiring box
X-axis motor
■
Pole-type with whipover cable
Independent cable
between XY
Y-axis motor
Y-axis
Y-axis slider
(tool installation section)
X-axis stroke cover
Robot cable
X-axis
X-axis slider
X-axis wiring box
X-axis motor
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
■ XZ-type with cable carrier
Z-axis
Z-axis wiring box
Z-axis motor
Cable carrier between XY
(The machine harness between XZ
is wired inside)
X-axis wiring box
Robot cable
Z-axis slider
Z-axis cover stroke
X-axis motor
X-axis
X-axis stroke cover
■ XZ-type with whipover cable
whipover cable between XY
Z-axis
Z-axis motor
X-axis wiring box
Robot cable
Z-axis slider
X-axis
X-axis motor
X-axis stroke cover
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Product Outline
3
Robot Controller
A RCX40, QRCX, TRCX or DRCX Series robot controller is enclosed with the
XY-X Series according to the user’s order.
Refer to the separate “YAMAHA Robot Controller Instruction Manual” for de-
tails on the robot controller.
DRCX
TRCX
MOTOR
OP.1
OP.3
RCX40
PWR
SRV
ERR
MPB
XM
YM
ROB
I/O
XY
BATT
COM
X
Y
Z
R
ROB
I/O
ZR
OP.2
OP.4
RGEN
ZM
RM
STD.DIO
P
N
SAFETY
P
O
W
E
R
C
P
U
O
K
S
A
E
R
V
O
L
A
ACIN
R
M
L
N
QRCX
RCX40
Robot Controller
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
Preparing the Robot
1 Robot Installation Environment...............................................3-1
2 Unpacking the Robot ..............................................................3-2
3 Checking the Product .............................................................3-3
4 Transporting the Robot ...........................................................3-5
5 Installation ..............................................................................3-7
5-1 Installation base ............................................................................... 3-7
5-2 Installing the Robot .......................................................................... 3-8
6 Protective connections ...........................................................3-9
7 Connecting the Robot Cables...............................................3-10
7-1 Connecting with the DRCX controller ............................................ 3-12
7-2 Connecting with the TRCX controller ............................................. 3-14
7-2-1 3-axis model ..................................................................................3-14
7-2-2 4-axis model ..................................................................................3-16
7-3 Connecting to the QRCX or RCX40 controller............................... 3-18
8 Installing the Tool ..................................................................3-20
9 User Wiring and User Piping ................................................3-21
10 Setting the Robot ..................................................................3-22
10-1 Setting the payload ........................................................................ 3-22
10-2 Setting the maximum speed .......................................................... 3-23
10-3 Setting the acceleration ................................................................. 3-24
11 Absolute Reset .....................................................................3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
1
Robot Installation Environment
WARNING
Avoid installing the robot in locations where the ambient conditions may
exceed the allowable ambient temperature or relative humidity, or in envi-
ronments where excessive moisture, corrosive gas, metallic powder or
dust is generated.
Malfunctions, failures or short circuits may otherwise result.
WARNING
• This robot is not designed for operation in environments where inflam-
mable of explosive substances are present.
• Do not use the robot in environments containing inflammable gas, dust
or liquids.
Explosions or fire might otherwise result.
WARNING
Do not use the robot in locations subject to excessive vibration. Robot
installation bolts may otherwise become loose causing the robot to fall
over.
!
CAUTION
Avoid using the robot in locations subject to electromagnetic interference, elec-
trostatic discharge or radio frequency interference.
Malfunctions might otherwise occur.
Always install the robot in the following type of environment.
Item
Specifications
Allowable ambient temperature
0 to 40°C
Allowable ambient relative humidity 35 to 80%RH (with no dew condensation)
Altitude
0 to 1000m above mean sea level
Ambient environment
Avoid installing near water, cutting water, oil, dust,
metallic chips or organic solvent.
Avoid installing near corrosive gas or corrosive materials.
Avoid installing in atmosphere containing inflammable gas,
dust or fluid.
Avoid installing near objects causing electromagnetic
interference, electrostatic discharge or radio frequency
interference.
Vibration
Do not subject robot to impact or vibration.
Air supply pressure, etc.
Supply clean dry air, that does not contain deteriorated
compressor oil, etc., at a pressure within 0.58MPa
(6.0kgf/cm2).
The air filter filtering degree must be 40µm or less.
Working space
Allow sufficient space so that work (teaching, inspection,
repairs, etc.) can be carried out safely.
Refer to the “YAMAHA Robot Controller Instruction Manual” for details on the
controller installation conditions.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
2
Unpacking the Robot
WARNING
The robot and robot controller are heavy. Take care not to drop these
parts or damage the devices while unpacking the packages.
The packages are divided into the robot (XY-X Series), robot controller (RCX40,
QRCX, TRCX or DRCX Series) and accessories according to the items ordered
by the user.
Carefully unpack the packages while taking care not to damage the devices.
Robot (XY-X Series)
Accessories
Robot controller
(RCX40, QRCX, TRCX or DRCX Series)
Example of packaging state
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
3
Checking the Product
!
CAUTION
Contact your YAMAHA dealer immediately if any parts are missing or have
been damaged during transportation.
After unpacking, check the state of the components and the product.
An example of the common combination of components is shown below. Check
the products according to the actual order.
Example of combination with RCX40 controller
ZR-axis unit (option)
I/O connector set for user
Robot (XY-X Series)
Robot cable
OWNER'S MANUAL
Controller power connector
Terminator
STD I/O connector
RCX40 controller
OP DI, OP DO connector
(option)
MPB programming unit (option)
Warning labels
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
Example of combination with TRCX controller
Z-axis unit (option)
Robot (XY-X Series)
I/O connector set for user
OWNER'S MANUAL
Robot cable
Controller power
connector
STD I/O connector
TRCX controller
Terminator
OP DI, OP DO connector
(option)
Y
A
M
A
H
A
Y
A
M
A
H
A
M
O
T
TPB programming unit
(option)
O
R
C
O
.
,
L
T
D
Warning labels
Example of combination with DRCX controller
Robot (XY-X Series)
I/O connector set for user
OWNER'S MANUAL
Robot cable
Controller power
connector
I/O connector
DRCX connector
Y
A
M
A
H
A
TPB programming unit
(option)
Y
A
M
A
H
A
M
O
T
O
R
C
O
.,
L
T
D
Warning labels
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
4
Transporting the Robot
WARNING
Serious injury may occur if the robot being transported falls and pins
someone under it.
• Use a hoist and rope with transporting capacity strong enough to sup-
port the robot weight.
• Make sure the rope stays securely on the hoist hook.
• Remove all loads attached to the robot end. If any load is still attached,
the robot balance may shift while being transported, and the robot may
topple over causing accidents.
• Always wear a safety helmet, safety shoes and gloves during this work.
• When transporting the robot by equipment such as a forklift, which
requires a license, only properly qualified personnel may operate such
equipment. The equipment and tools used for transporting the robot
should be serviced daily.
WARNING
Hands and fingers could get caught and serious injury could result if the
slider moves while transporting the robot.
Accidents could also result if the weight balance shifts and the robot drops,
etc.
• Fix the slider with a rope, etc., to prevent movement during transporta-
tion.
• Do not place fingers between frame and cover during transportation.
• Do not tilt the robot during transportation.
WARNING
Observe the following precautions when temporarily installing the robot.
Failure to observe these could cause injuries to hands or fingers if the
robot tilts over.
• Always fix the robots with bolts even when only temporarily installing
the robot.
• When temporarily installing the arm type without using bolts, set a
spacer under the arm, etc., to prevent the robot from tilting over. Make
sure that the spacer has sufficient strength and stability.
• The pole-type robot’s stability is especially poor, so take special care
to prevent tilting during temporary installation.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
Use of a hoist, dolly or forklift is recommended for transporting the robot or
controller. Use sufficient caution when transporting robots with a long stroke or
large payload as they are heavy.
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
5
Installation
5-1
Installation base
WARNING
If the installation base is not sufficiently rigid and stable, vibration (reso-
nance) may occur during operation and adversely affect the robot work.
In worst cases the robot might even fall over causing a serious accident.
!
CAUTION
If the installation surface accuracy is insufficient, the robot positioning accuracy
and machine life may drop, and noise may be generated.
1) Select an installation base that has sufficient rigidity and stability to with-
stand the robot (including tool) and workpiece weight and the reaction gen-
erated during operation.
2) The installation base surface must be machined to a flatness within 0.05mm/
500mm.
3) If there is a clearance between the installation base and robot frame when the
robot is set on the base, insert suitably thick shims in the clearance to prevent
stress from being applied on the robot frame.
4) Avoid fixing the robot onto the installation base with less than the specified
number of bolts, or installing only one end of the robot. Failure to observe
this could lead to an increase in robot vibration and decrease in positioning
accuracy.
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
5-2
Installing the Robot
Always observe the safety precautions and the following procedures to ensure
that the robot is correctly and safety installed.
WARNING
• Take care not to pinch hands, etc., when removing the hoist belt from
the X-axis.
• The robot could tilt over if the hoist belt comes undone and if the bal-
ance is lost. Prevent tilting by suspending the tilting section with a
hoist or by using spacers, etc.
1) Tap or hole is machined into the installation base where the robot is to
be secured.
Refer to the XY-X Series catalog for the machining dimensions and posi-
tions.
2) Fix the installation base at the specified position.
Securely fix the installation base so that it will not sway during robot opera-
tion. (Depending on the installation place or installation base shape, this step
may be carried out after the robot is fixed onto the installation base.)
3) Using a hoist, carefully place the robot onto the installation base.
4) Remove the hoist belt from the Robot.
5) Install the robot referring the explanation for each robot in Chapter 6
and following.
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
6
Protective connections
WARNING
Be sure to ground the robot and controller to prevent electrical shock.
WARNING
Turn the controller power OFF before starting connecting the ground.
The ground terminal position differs for each robot. Refer to the explanation for
each robot in Chapter 6 and following for details.
1) Provide a terminal marked “PE” as the protective conductor for the entire
system, and connect to an external protective conductor. Also securely con-
nect the ground terminal on the robot base to the protective conductor.
(Symbol 417-IEC-5019)
2) When the end effector uses an electrical device which, if it malfunctions,
might make contact with the power supply, the user must provide proper
grounding on his own responsibility. The XY-X series robots do not have a
ground terminal for this purpose.
3) For details on protective bonding on the robot body to comply with CE mark-
ing, follow the instructions on protective bonding explained in the "YAMAHA
QRCX-E robot controller owner's manual".
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
7
Connecting the Robot Cables
WARNING
1. The robot cable is the most important cable for controlling the robot. If
the connector is insufficiently connected and there are pin contact
faults, the robot could malfunction. Confirm that each connector is
securely connected before turning the controller power ON.
2. Arrange the connected cables so that they will not get in the way of
robot movements or the operator’s operations. Make sure that exces-
sive load is not applied on the connector due to pulling of the cables.
WARNING
• Before connecting the cables, check that there are no bends or breaks
in the robot cable connector pins and that the cables are not damaged.
Bent or broken pins or cable damage may cause robot malfunctions.
• Turn the controller power OFF before connecting the controller and
robot cable.
WARNING
With the RCX40, QRCX and TRCX4 controllers, the motor connectors XM
and ZM, YM and RM and Robot I/O connectors XY and ZR have the same
shape. Take special care when connecting as incorrect connections could
cause malfunctions.
WARNING
With the TRCX3 controller, the motor connectors XM and ZM have the
same shape. Take special care when connecting as incorrect connections
could cause malfunctions.
WARNING
• If the connector is insufficiently connected and there are pin contact
faults, the robot could malfunction. Confirm that each connector is se-
curely connected before turning the controller power ON.
• Before turning on the controller, check that the robot I/O connector is
securely attached.
• Make sure that excessive load is not applied on the connector due to
pulling of the robot cables.
WARNING
Arrange the robot cable so that it will not get in the way of robot move-
ments. Do not set the area where the robot cable interferes with the load
on the robot tip as the working envelope. If the robot’s moving sections
interfere with the cable, the robot cable could be damaged and malfunc-
tions could occur.
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
WARNING
Arrange the connected robot cable so that it will not get in the way of
operator’s operations. The operator could trip on the robot cable and be
injured.
WARNING
When connecting the robot cable, insert the robot cable connector straight
into the mating connector on the controller. Inserting the connector while
tilted might cause the pins to make poor contact, causing robot malfunc-
tion and the connector itself might even break.
!
CAUTION
These connectors all work in only one direction. Take a good look at the con-
nector shape before trying to attach it. Connecting the wrong way may damage
the connectors.
The robot cable is connected beforehand to the XY Series robot side.
Correctly install the other end of the robot cable to the robot controller. For de-
tails on connections to the robot controller, refer to 7-1 to 7-4.
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
7-1
Connecting with the DRCX controller
WARNING
When connecting the robot cable, insert the robot cable connector straight
into the mating connector on the controller. Inserting the connector while
tilted might cause the pins to make poor contact, causing robot malfunc-
tion and the connector itself might even break.
!
CAUTION
These connectors all work in only one direction. Take a good look at the con-
nector shape before trying to attach it. Connecting the wrong way may damage
the connectors.
1) Prepare the required tools.
Precision phillips-head screwdriver.
2) While referring to Table 3-1 and Fig.3-1, securely insert the motor connector
into the correct position on the controller unitl a click is heard.
3) While referring to Table 3-1 and Fig.3-1, insert the robot I/O cable into the
correct position on the controller.
4) Use the precision phillips-head screwdriver to tighten the robot I/O connec-
tor screws.
Table 3-1
Robot cable
DRCX
MOTOR X
MOTOR Y
ROB I/O
XM
YM
XY
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
MOTOR connector
Robot cable
ROBOT
I/O connector
DRCX controller
To robot
Fig. 3-1 Connection to DRCX controller
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
7-2
Connecting with the TRCX controller
7-2-1
3-axis model
WARNING
When connecting the robot cable, insert the robot cable connector straight
into the mating connector on the controller. Inserting the connector while
tilted might cause the pins to make poor contact, causing robot malfunc-
tion and the connector itself might even break.
!
CAUTION
These connectors all work in only one direction. Take a good look at the con-
nector shape before trying to attach it. Connecting the wrong way may damage
the connectors.
!
CAUTION
With the TRCX3 controller, the MOTOR connectors XM and ZM have the same
shape. Take care not to reverse the robot cable XM and ZM when connecting.
1) Prepare the required tools.
Precision phillips-head screwdriver.
2) While referring to Table 3-2 and Fig.3-2, securely insert the motor connector
into the correct position on the controller unitl a click is heard.
3) While referring to Table 3-2 and Fig.3-2, insert the robot I/O cable into the
correct position on the controller.
4) Use the precision phillips-head screwdriver to tighten the robot I/O connec-
tor screws.
Table 3-2
Robot cable
TRCX
XM
YM
XY
ZM
Z
MOTOR X
MOTOR Y
ROB I/O
Main side unit
MOTOR Z
ROB I/O
Sub-side unit
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
MOTOR
connector
ROBOT
I/O connector
MOTOR
connector
ROBOT
I/O connector
Robot cable
To robot
Fig. 3-2 Connection to TRCX controller (3-axis model)
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
7-2-2
4-axis model
WARNING
When connecting the robot cable, insert the robot cable connector straight
into the mating connector on the controller. Inserting the connector while
tilted might cause the pins to make poor contact, causing robot malfunc-
tion and the connector itself might even break.
!
CAUTION
These connectors all work in only one direction. Take a good look at the con-
nector shape before trying to attach it. Connecting the wrong way may damage
the connectors.
!
CAUTION
With the TRCX4 controller, the MOTOR connector and PI connector shapes
are the same for the XY-axis and ZR-axis. Take care not to reverse the robot
cables XY and ZR when connecting.
1) Prepare the required tools.
Precision phillips-head screwdriver.
2) While referring to Table 3-3 and Fig.3-3, securely insert the motor connector
into the correct position on the controller unitl a click is heard.
3) While referring to Table 3-3 and Fig.3-3, insert the robot I/O cable into the
correct position on the controller.
4) Use the precision phillips-head screwdriver to tighten the robot I/O connec-
tor screws.
Table 3-3
Robot cable
TRCX
XM
YM
XY
ZM
RM
ZR
MOTOR X
MOTOR Y
ROB I/O
Main side unit
MOTOR X
MOTOR Y
ROB I/O
Sub-side unit
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
MOTOR
connector
MOTOR
connector
ROBOT
I/O connector
ROBOT
I/O connector
Robot cable
To robot
Fig. 3-3 Connection to TRCX controller (4-axis model)
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
7-3
Connecting to the QRCX or RCX40 controller
WARNING
When connecting the robot cable, insert the robot cable connector straight
into the mating connector on the controller. Inserting the connector while
tilted might cause the pins to make poor contact, causing robot malfunc-
tion and the connector itself might even break.
!
CAUTION
These connectors all work in only one direction. Take a good look at the con-
nector shape before trying to attach it. Connecting the wrong way may damage
the connectors.
!
CAUTION
With the RCX40, QRCX controller, the MOTOR connector and PI connector
shapes are the same for the XY-axis and ZR-axis. Take care not to reverse the
robot cables XY and ZR when connecting.
1) Prepare the required tools.
Precision phillips-head screwdriver.
2) While referring to Table 3-4 and Fig.3-4, Fig.3-5, securely insert the motor
connector into the correct position on the controller unitl a click is heard.
3) While referring to Table 3-4 and Fig.3-4, Fig.3-5, insert the robot I/O cable
into the correct position on the controller.
4) Use the precision phillips-head screwdriver to tighten the robot I/O connec-
tor screws.
Table 3-4
Robot cable
RCX40, QRCX
MOTOR1 (X side)
MOTOR1 (Y side)
MOTOR2 (Z side)
MOTOR2 (R side)
PI1
XM
YM
ZM
RM
XY
ZR
PI2
Note)This is for the main robot.
Refer to the controller instruction manual for details.
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
1
2
XY
ZR
Connect to YAMAHA robot
Robot cable
Fig. 3-4 Connection to QRCX controller
XM
YM
XY
ZR
ZM
RM
Connect to YAMAHA robot
Fig. 3-5 Connection to RCX40 controller
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
8
Installing the Tool
WARNING
The user must responsibly determine the bolt type and tightening torque
for the tool installation, and must accurately tighten these. Improper in-
stallation could cause the tool to dislocate during operation and lead to
serious accidents.
!
CAUTION
Install the tool at the designated section. Avoid installing heavy objects on the
other sections (Y-axis frame or X-axis slider, etc.).
Failure to observe this could lead to vibration during operation (especially dur-
ing positioning).
Install user's tools on the sections designated as tool installation sections, such as
the robot slider and bracket. (Refer to Chapter 2 2. Names of each part and expla-
nations for each robot in Chapter 6 and following for each robot for details on the
designated sections.)
Refer to the explanation for each robot in Chapter 6 and following for details on
the actual installation methods.
3-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
9
User Wiring and User Piping
!
CAUTION
Do not clamp the wires or pipes to the outside of the whipover cable. The
whipover cable could sag or break and ultimately be disconnected.
After completing all work up to step 8, wires and pipes are laid from the user’s
devices or robot controller to the tools and valves installed on the robot.
■ Cable carrier type
Carry out wiring and piping using the attached cable carrier.
Refer to the explanation for each robot in Chapter 6 and following for details
on the actual wiring and piping methods and precautions.
The cable carrier contains a user I/O cable (0.3sq×10) for user wiring, so there
is no need to add harnesses and route them through the cable carrier.
Refer to Chapter 3, “12. Specifications” for the specifications on the user I/O
wire, and the explanation of each robot in Chapter 6 for details on the wiring
methods.
■ whipover cable carrier type
The signal wires (0.3mm2×10 wires) and air tubes (4×2.5×2 tubes) are laid in
the whipover cable beforehand. Use these for wiring and piping to the tools.
Refer to the explanation for each robot in Chapter 6 and following for details
on the actual wiring and piping methods and precautions.
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
10
Setting the Robot
10-1
Setting the payload
!
CAUTION
Always input an accurate value as an incorrect value can lead to various trou-
ble including vibration and a drop in machine life.
!
CAUTION
When installing a weight other than the tool or workpiece on the robot’s moving
section, add that weight. (For example, if an air valve is fixed on the Y-axis
frame, include that weight in the payload.)
The optimum acceleration and servo gain, etc., are automatically set for the
cartesian robot XY-X Series by inputting the controller payload parameters.
Set the total value of the tool weight and workpiece weight as a kg unit in the
payload parameter.
■ List of payload parameters
Controller
DRCX
Payload parameter
PRM90
TRCX3
PRM130
TRCX4
PRM170
RCX40, QRCX
Robot parameter "1. Tip weight"
Refer to the following sections in the Robot Controller Instruction Manual, and
set the payload parameters.
For DRCX or TRCX controller
Chapter 5 Parameters
For RCX40 or QRCX controller
Chapter 4 Operation > 12. System Mode > 12-1-1. Robot parameters
3-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
10-2
Setting the maximum speed
When operating a ball screw driven robot, the ball screw's free length will in-
crease as the movement stroke increases, and the resonance frequency will drop.
Thus, the ball screw may resonate and generate vigorous vibration depending on
the motor rotation speed. (The speed at which resonance occurs is called the
whirling speed.) To prevent this resonance, the maximum speed setting must be
lowered if the movement stroke increases depending on the robot model.
!
CAUTION
Continuing use while the ball screw is resonating will cause the ball screw to
wear out prematurely.
!
CAUTION
There are cases when the whirling speed is not reached depending on the
movement point. (The ball screw’s nut acts as the support material, so when
operating the robot near the center of the stroke, the ball screw's free length will
be shortened and resonance will not occur as easily.) If resonance does not
occur when the robot is actually operated, the speed can be increased.
■ Models requiring lower maximum speed setting
FXYX
SXYX
MXYX
HXYX
X-axis stroke 750mm or more
X-axis stroke 750mm or more
X-axis stroke 850mm or more
X-axis stroke 850mm or more
Refer to the catalog for the maximum speed setting values.
The maximum speed can be reduced by lowering the speed setting for automatic
operation or by lowering the speed with a program command. The user should
select the suitable method.
Refer to the following sections in the Robot Controller Instruction Manual for
details on changing the speed setting during automatic operation.
For ERCX, SRCX, DRCX or TRCX controller
Chapter 9 Robot Operation > 9-3. Automatic Operation
For RCX40 or QRCX controller
Chapter 4 Operation > 9. "Auto" Mode > 9-6. Changing the automatic movement speed
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
10-3
Setting the acceleration
The acceleration is automatically set for the Cartesian robot XY-X Series when
the payload parameter is set, so large vibration will not occur during operation.
However, if the tool or workpiece is greatly offset from the robot, vibration may
occur especially during positioning.
In this case, lower the controller's acceleration setting.
Lowering the acceleration is also effective if tool or workpiece vibration occurs
due to a low tool rigidity.
■ List of acceleration parameters
Controller
DRCX
TRCX3
TRCX4
Acceleration parameter
X-axis PRM51 Y-axis PRM91
X-axis PRM51 Y-axis PRM91 Z-axis PRM131
X-axis PRM51 Y-axis PRM91 Z-axis PRM131
R-axis PRM171
RCX40, QRCX Axis parameter "1. Acceleration coefficient"
Refer to the following sections in the Robot Controller Instruction Manual, and
change the acceleration.
For DRCX or TRCX controller
Chapter 5 Parameters
For RCX40 or QRCX controller
Chapter 4 Operation > 12. "System" Mode > 12-1-2. Axis parameters
3-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
11
Absolute Reset
Refer to this section and set the origin position before using the robot.
The Cartesian robot XY-X Series uses an absolute method position detector, and
thus return-to-origin is not required when the controller power is turned ON again.
However, the origin position must be set the first time the controller power is
turned ON from any of the following states.
(1) When robot cable is connected for the first time after delivery
(2) When the cable connection between the robot cable and controller has
been disconnected
(3) When the absolute battery is not connected
(4) When the motor or cable is replaced
One of the following errors will appear when the power is turned ON in any of
the above cases, but this is not an error. The robot will operate normally when the
power is turned ON again.
For DRCX or TRCX controller
15: FEEDBACK ERROR 2
23: ABS. BAT. L-VOLTAGE
24: ABS. DATA. ERROR
For QRCX controller
17.80:D?.ABS.Encoder backup error
17.81:D?.ABS.Encoder battery alarm
17.85:D?.ABS.Encoder system error
17.92:D?.ABS.Cable disconnected
17.93:D?.ABS.Data overflow
17.94:D?.ABS.Battery degradation
For RCX40 controller
17.27 : D?.ABS. backup failed (CPU)
17.80 : D?.ABS. backup failed (DRIVER)
17.81 : D?.ABS.battery wire breakage
17.92 : D?.Resolver disconnected during power off
17.93 : D?.Position backup counter overflow
17.94 : D?.ABS.battery low voltage
etc
Note) Question marks (?) in the above error messages indicate the axis num-
bers.
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
■ Setting the origin position
[1] For robot configured of only linear movement axis
The above type of robot uses a stroke end detection method as origin return.
The motor side stroke end is set as the origin detection position before ship-
ment from the factory. (Excluding ZH and the Z-axis of ZS, ZRS.)
!
CAUTION
Avoid changing the origin position to the non-motor side as the position could
deviate, trouble could occur, and could be hazardous in some cases. Always
consult with YAMAHA when the origin position must be changed.
Refer to the following sections in the Robot Controller Instruction Manual
and set the origin.
For ERCX, SRCX, DRCX or TRCX controller
Chapter 9 > 9-1. Returning-to-the Origin > 9-1-1. Return-to-origin by the search method
For QRCX controller
Chapter 11 > 11-9. Absolute reset
For RCX40 controller
Chapter 11 > 11-8. Absolute reset
[2] When robot contains a rotary axis
Target rotary axis
RF
RL/RH
RS
(R-axis for SXYX/MXYX/SXYBX)
(R-axis for HXYX)
(R-axis for ZRS unit)
The above rotary axes uses mark method return-to-origin.
Thus, if the robot contains this type of axis, the origin position of the rotary axis
can be set freely by the user.
Refer to the following sections in the Robot Controller Instruction Manual, move
the robot to the preferred origin, and then set the origin.
For DRCX or TRCX controller
Chapter 9 > 9-1. Returning-to-the Origin > 9-1-2. Return-to-origin by the mark method
Return the rotary axis to the origin before returning the other linear movement
axes to the origin. (Refer to section [1] above for details on returning the linear
movement axis to the origin.)
For QRCX controller
Chapter 11 > 11-9. Absolute reset
For RCX40 controller
Chapter 11 > 11-8. Absolute reset
3-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
When MANUAL > RST.ABS > ALL is selected on the MPB screen (see “11-9-
3” in QRCX owner’s manual or “11-8-3” in RCX40 owner’s manual), first per-
form absolute reset for the rotating axis and then other linearmovement axes.
When performing absolute reset for each axis one by one (see “11-9-2” in QRCX
owner’s manual or “11-8-2” in RCX40 owner’s manual), you can begin in any
order.
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing the Robot
After setting the origin position, attach the label enclosed with the robot so that it
acts as a match mark on the tool side and Robot side. This match mark will be the
reference for subsequent origin settings.
Figure
Slit
Origin position label
(enclosed with product)
Example: ZRS
Origin position label
Example: RH
3-28
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
Periodic Inspections
1 Outline ....................................................................................4-1
2 Precautions.............................................................................4-1
3 Daily inspection ......................................................................4-2
4 Three-month inspection ..........................................................4-2
5 Six-month inspection ..............................................................4-3
6 Three-year inspection .............................................................4-4
7 Replenishing the grease .........................................................4-5
8 Maintenance and inspection of harmonic drives ....................4-6
8-1 Harmonic grease replacement period.............................................. 4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
1
Outline
Implementation of periodic inspections is essential to ensure safe and efficient
operation of the YAMAHA robot.
The periodic inspection items and procedures for the XY Series are described in
this chapter.
The periodic inspections include;
• Daily inspection
• Three-month inspection
• Six-month inspection
• Three-year inspection
Thoroughly understand the details of the inspection and observe the precautions
during this work.
2
Precautions
Always read the safety precautions in “Chapter 1 Using the Robot Safely” and
follow the instructions. Important precautions are listed below again for refer-
ence.
DANGER
• Never enter the robot’s movement area when operating the robot dur-
ing adjustments and inspections. Pay attention to the robot movements
and surrounding safety so that the emergency stop button can be
pressed immediately when any hazard is sensed.
WARNING
• Always turn the controller power switch and external power distribu-
tion board switch OFF before starting adjustments and inspections
that do not require robot operation.
• Press the emergency stop button when robot operation is not required
during the electrical system inspection.
• Use only lubricant designated by YAMAHA or your dealer.
• Use only parts designated by YAMAHA or your dealer when replacing
parts. Make sure that foreign matter does not enter the robot during
adjustment, part replacement or reassembly.
• Never modify the robot or controller, etc. Modifications may result in
improper specifications and may threaten operator safety.
• Always tighten the bolts and screws securely after completing adjust-
ments or inspections.
• During robot adjustment or inspection, place a sign indicating that the
robot is being adjusted or inspected, to prevent others from touching
the switches. Provide a switch key lock mechanism or assign a moni-
tor if necessary.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
3
Daily inspection
Check the following points before and after robot operation every day. Make
adjustments and replacements as necessary.
Check point
Safeguard enclosure
Check items
Check that the safeguard enclosure is securely
fixed at the designated position.
Cables
Check for damages, dents and excessive bending.
Check for the adherence of chemicals.
Check for abnormal vibration or noise, and for
abnormal temperature rise.
• Check that the air pressure is correct.
• Check that there are no air leaks.
Motor, speed
reduction gear
Pneumatic devices
• Check that the water has been drained.
• Check that the air filter is not contaminated.
4
Three-month inspection
Check the following points every three months, and replenishing grease if re-
quired. (To replace grease, see “7 Replenishing the grease”.)
Check point
Check items
• Clean off any dirt or contamination. Replenish
the grease after cleaning.
Replenishment of
• Replenish grease if the items on the left are dry
or do not have enough grease.
grease to X, Y and Z
axis ball screw, linear
guide and ball spline
Standard specifications: Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
Clean room specifications: LG-2 (NSK)
!
CAUTION
Use of grease not recommended by YAMAHA may lead to a drop in the ball
screw, linear guide, ball spline and linear bushing shaft life. When using the
clean room specifications, the degree of cleanliness may drop.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
5
Six-month inspection
Check the following points every six months, and make adjustments or replace-
ments as required.
Check point
Robot's main bolts
and screws
Check items
Check for looseness, and tighten if necessary.
X-axis, Y-axis and
Z-axis drive sections
(ball screw, linear
guide)
• Check for looseness in the X-axis, Y-axis and
Z-axis drive section (ball screw, linear guide).
Tighten if necessary.
• Check for vibration during operation. Tighten
the drive section, and X-axis, Y-axis and Z-axis
installation bolts if necessary.
• Check for looseness caused by wear. Contact
YAMAHA if any abnormality is found.
Check for looseness.
(Contact YAMAHA if any abnormality is found.)
• Check the timing belt tension.
Z-axis ball spline and
ball screw (for ZS, ZRS)
R-axis timing belt
(for ZRS)
• Check the timing belt for abnormalities (cracks
or cuts).
Wiring in robot
• Check the cables for damage.
• Check the relay connectors, etc., for looseness.
• Inspect the timing belt for abnormalities (cracks
or cuts).
Belt
(for FXYBX, SXYBX,
ZRS, HXYLX)
Controller
• Check the timing belt tension.
• Check the terminals for looseness.
• Check the connection connectors for looseness.
• Check that the fan is rotating.
• Check whether anything is obstructing the fan.
• Check the rotating fan for abnormal sounds.
Check visually if any abnormal sound is heard,
and remove any foreign matter. Contact
YAMAHA if no foreign matter is found.
• Check the fan cover for contamination. Remove
and clean the cover if contaminated.
Controller rear panel
cooling fan
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
6
Three-year inspection
Check the following points once every three years, and adjust or replenish grease
as necessary.
If the robot is used frequently, inspect the robot at an earlier stage.
Check point
R-axis speed
reduction gear
Check items
Disassemble and check the harmonic drive.
Replace the grease.*
X-axis, Y-axis and
Z-axis drive section
(Ball screw nut
section, motor section
and linear guide)
Check the ball screws, nuts and linear guide for
looseness caused by wear.
*To replace harmonic drive grease, see "8 Maintenance and inspection".
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
7
Replenishing the grease
WARNING
Precautions for handling grease
• Inflammation may occur if the grease gets into eyes.
Always wear protective goggles, etc., to protect eyes when handling
the grease.
• Inflammation may occur if the grease gets on skin. Wear protective
gloves, etc., to protect skin when handling the grease.
• Do not consume the grease. (Consumption of grease will cause diarrhea
and vomiting.)
• Wear protective gloves when opening the can to prevent injury to hands.
• Store the grease out of the reach of children.
• Do not heat the grease or place it near fire. There is a risk of igniting or
fires.
Remedial measures
• If the grease gets into eyes, flush eyes for 15 minutes with clean water,
and then see doctor.
• If the grease gets on skin, wash off completely with water and soap.
• If the grease is consumed, do not induce vomiting, and instead con-
sult with a doctor immediately.
!
CAUTION
Use of grease not recommended by YAMAHA may lead to a drop in the ball
screw, linear guide, ball spline and linear bushing shaft life. When using the
clean room specifications, the degree of cleanliness may drop.
!
CAUTION
When replenishing clean grease, manually apply a thin coat on the screws and
the entire length of the spline shaft.
Refer to the periodic inspections in the explanation for each robot in Chapter 6
and following, and replenish the grease. Observe the following points when re-
plenishing the grease.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
8
Maintenance and inspection of harmonic drives
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts during inspection or servicing, turn OFF the controller,
wait for a while and check that the part has cooled.
WARNING
Precautions for handling harmonic grease and washing oil
• Inflammation may occur if the grease gets into eyes.
Always wear protective goggles, etc., to protect eyes when handling
the grease.
• Inflammation may occur if the grease gets on skin. Wear protective
gloves, etc., to protect skin when handling the grease.
• Do not consume the grease. (Consumption of grease will cause diarrhea
and vomiting.)
• Wear protective gloves when opening the can to prevent injury to hands.
• Store the grease out of the reach of children.
• Do not heat the grease or place it near fire. There is a risk of igniting or
fires.
Remedial measures
• If the grease gets into eyes, flush eyes for 15 minutes with clean water,
and then see doctor.
• If the grease gets on skin, wash off completely with water and soap.
• If the grease is consumed, do not induce vomiting, and instead con-
sult with a doctor immediately.
WARNING
Disposal of harmonic grease, spent washing oil and waste containers
• Disposal methods are specified by law. Always follow local laws when
disposing of these items.
• Do not apply pressure on an empty container. The container could rup-
ture if pressurized.
• Do not weld, heat, open a hole or cut this container. Failure to observe
this could lead to an explosion and igniting of the residual matter.
!
CAUTION
Use of grease not recommended by YAMAHA could lead to a drop in the har-
monic drive life.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Periodic Inspections
!
CAUTION
Harmonic drive
• Do not apply strong impacts on any part with a hammer, etc. Do not damage
or mark the parts by dropping. There is a risk of damage.
• The specified performance cannot be attained if a damaged part is used.
Continued use of a damaged part could lead to trouble such as rupture.
Harmonic grease HC-1A (Harmonic Drive Systems) is used to lubricate the har-
monic drive used for the R-axis (ZRL, ZRH, ZRF unit) speed reduction gear. The
life of the harmonic drive could be shortened if this grease deteriorates.
Determine an inspection interval at every three years or to suit the usage condi-
tions, and replace the grease.
The ZRS unit's R-axis also uses a harmonic drive, but the grease does not need to
be replaced.
8-1
Harmonic grease replacement period
The harmonic grease should be replaced when the total number of wave genera-
tor rotations reaches 1.5 × 108 times (at -10°C to +40°C). Thus, the replacement
period will differ according to the following usage conditions.
n
θ
N
: Number of arm movements in one minute
: Average arm rotation in one movement
: 1/deceleration rate
h
D
: Number of operation hours per day
: Number of operation days per year
The method of calculating the replacement period using the following conditions
is shown as an example.
n
: 10 times
θ
N
: 1/4 rotation
: 80
h
D
: 24 hours/day
: 240 days/year
Replacement period = 1.5 × 108/ ( n × 60 × h × D × N × θ )
= 1.5 × 108/ ( 10 × 60 × 24 × 240 × 80 × 1/4 )=2.17 years
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
Specifications
1 Specifications .........................................................................5-1
1-1 Robot cable ...................................................................................... 5-1
1-2 User I/O cable .................................................................................. 5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Specifications
1
Specifications
The specifications of each robot's common parts are shown below.
1-1
Robot cable
This cable is used to connect the controller and robot.
Signal
Resolver
Connector
No
1
2
3
4
5
6
7
1
2
1
2
3
4
5
6
7
1
2
Connection
No
Connector
Color/No.
Blue
Wire
S2
S4
1
0.3sq
twisted pair
2
Orange
Green
Brown
Gray
S1
3
0.3sq
XP
r
twisted pair
S3
4
R1
5
0.3sq
twisted pair
R2
6
Red
DG
7
Green
Black
0.3sq
Brake
MB+
MB-
S2
14
16
19
20
21
22
23
24
25
32
34
10
11
28
29
0.3sq
XBK
t
twisted pair
Yellow
Pink
Resolver
0.3sq
twisted pair
S4
Purple
White
Blue/Red
XY
q
S1
0.3sq
YP
y
twisted pair
S3
R1
Orange/White 0.3sq
twisted pair
0.3sq
R2
Green/White
Green
DG
Brake
Brown/White 0.3sq
MB+
MB-
HLIM
GND24
HLIM
GND24
YBK
u
twisted pair
Gray/White
Green
Green
27
30
31
2
Sensor
Red/White
Yellow/Black
Pink/Black
24V
ORG
GND24
U
0.3sq
ORG
i
2
3
0.3sq
twisted pair
1
2
3
0.75sq
0.75sq
0.75sq
XM
o
XM
w
V
2
3
4
1
2
3
4
3
W
4
FG Ring-tongue terminal
1
Yellow /Green 0.75sq
U
2
4
5
6
0.75sq
0.75sq
0.75sq
YM
!
V
3
YM
e
W
4
Ring-tongue terminal
!
FG
r
XP
q
t
y
XBK
YP
u
i
YBK
XY
ORG
w
e
o
!
XM
YM
XM
YM
!
2-axis robot cable
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Specifications
Signal
Connector
No
1
2
3
4
5
6
7
1
2
1
2
3
4
5
6
7
1
2
Connection
No Connector
Color/No.
Blue
Wire
0.3sq
Signal
Connector
No
1
Connection
No Connector
Color/No.
Blue
Wire
0.3sq
S2
S4
1
2
S2
S4
1
2
3
4
5
6
9
Resolver
Resolver
twisted pair
twisted pair
Orange
Green
Brown
Gray
2
Orange
Green
Brown
Gray
S1
3
0.3sq
S1
3
0.3sq
XP
y
ZP
!
twisted pair
twisted pair
S3
4
S3
4
5
R1
R2
DG
5
0.3sq
R1
0.3sq
twisted pair
twisted pair
6
Red
R2
6
7
1
2
Red
7
Green
Black
0.3sq
DG
MB+
MB-
Green
Black
Yellow
0.3sq
Brake
Brake
MB+
MB-
S2
14
16
19
0.3sq
17
Z
w
0.3sq
XBK
u
ZBK
!
twisted pair
twisted pair
Yellow
Pink
18
0.3sq
Resolver
twisted pair
Pink
Sensor
24V
ORG
0.3sq
S4
20
21
22
23
24
25
Purple
White
Blue/Red
XY
q
ORG
!
0.3sq
S1
0.3sq
2
3
12
15
White
YP
i
twisted pair
twisted pair
S3
GND24
Blue/Red
R1
Orange/White 0.3sq
twisted pair
0.3sq
R2
Green/White
Green
DG
Brown/White 0.3sq
Brake
MB+
MB-
HLIM
GND24
HLIM
GND24
U
32
34
10
11
YBK
o
twisted pair
Gray/White
Green
Green
28
29
2
1
2
3
0.75sq
0.75sq
0.75sq
U
V
2
1
2
3
0.75sq
0.75sq
0.75sq
ZM
!
XM
!
V
2
3
4
3
2
3
4
4
XM
e
ZM
t
W
4
W
3
1
FG Ring-tongue terminal
U
1
Yellow/Green 0.75sq
FG Ring-tongue terminal
!
Yellow/Green 0.75sq
1
2
3
4
2
4
5
6
0.75sq
0.75sq
0.75sq
YM
!
V
3
YM
r
W
4
FG Ring-tongue terminal
!
q
y
i
XP
XBK
YP
u
o
YBK
XY
w
!
!
ZP
!
ZBK
ORG
Z
!
!
XM
YM
e
r
XM
YM
ZM
!
!
ZM
t
!
3-axis robot cable (For TRCX controller)
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Specifications
Signal
Connector
No
1
2
3
4
5
6
7
1
2
1
2
3
4
5
6
7
1
2
Connection
No Connector
Color/No.
Blue
Wire
0.3sq
Signal
Connector
No
1
Connection
No Connector
Color/No.
Blue
Wire
0.3sq
Resolver S2
1
2
Resolver S2
1
2
3
4
twisted pair
twisted pair
S4
S1
Orange
Green
Brown
Gray
S4
S1
2
Orange
Green
Brown
Gray
3
0.3sq
3
0.3sq
XP
y
ZP
(RP)
!
twisted pair
twisted pair
S3
4
S3
4
5
R1
R2
DG
5
0.3sq
R1
R2
DG
5
0.3sq
ZR
w
twisted pair
twisted pair
6
Red
6
7
1
2
6
Red
7
Green
Black
0.3sq
7
Green
Black
Yellow
0.3sq
ZBK
(RBK)
!
Brake
Brake
MB+
MB-
14
16
0.3sq
MB+
MB-
14
16
0.3sq
XBK
u
twisted pair
twisted pair
Yellow
Pink
Resolver S2
19
20
21
22
23
24
25
32
34
10
11
28
29
0.3sq
XY
q
twisted pair
Sensor
24V
9
S4
S1
Purple
White
Blue/Red
Red/White
Yellow/Black
Pink/Black
Green
0.3sq
ORG
i
ORG
2
3
12
13
10
11
28
29
2
0.3sq
0.3sq
YP
i
twisted pair
twisted pair
GND24
HLIM
GND24
HLIM
GND24
U
S3
R1
R2
DG
Orange/White 0.3sq
twisted pair
0.3sq
Green/White
Green
Green
Brake
MB+
Brown/White 0.3sq
YBK
o
twisted pair
Gray/White
Green
MB-
HLIM
GND24
HLIM
GND24
U
1
2
3
0.75sq
0.75sq
0.75sq
ZM
(RM)
!
ZM
(RM)
t
V
2
3
4
3
W
4
Green
FG Ring-tongue terminal
!
1
Yellow/Green 0.75sq
2
3
4
1
2
3
4
1
2
3
0.75sq
0.75sq
0.75sq
XM
!
V
2
3
4
1
2
3
4
XM
e
W
FG Ring-tongue terminal
Yellow/Green 0.75sq
U
4
5
6
0.75sq
0.75sq
0.75sq
YM
V
YM
r
!
W
Ring-tongue terminal
!
FG
q
y
XP
XBK
YP
u
i
o
YBK
XY
w
!
or RP
ZP
!
!
or RBK
ZBK
ZR
ORG
!
!
XM
YM
e
r
XM
YM
!
or RM
ZM
!
t
ZM
or RM
!
3-axis robot cable (For RCX40 controller)
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Specifications
Signal
Connector
No
1
2
3
4
5
6
7
1
2
1
2
3
4
5
6
7
1
2
Connection
No Connector
Color/No.
Blue
Wire
0.3sq
Signal
Connector
No
1
2
3
4
5
6
7
1
2
1
2
3
4
5
6
7
1
2
Connection
No Connector
Color/No.
Blue
Wire
0.3sq
Resolver S2
1
2
3
4
5
6
7
Resolver S2
1
2
twisted pair
twisted pair
S4
S1
Orange
Green
Brown
Gray
S4
S1
Orange
Green
Brown
Gray
0.3sq
3
0.3sq
XP
u
ZP
!
twisted pair
twisted pair
S3
S3
4
R1
R2
DG
0.3sq
R1
R2
DG
5
0.3sq
twisted pair
twisted pair
Red
6
Red
Green
Black
0.3sq
7
Green
Black
0.3sq
Brake
Brake
MB+
MB-
14
0.3sq
MB+
MB-
14
16
19
0.3sq
XBK
i
ZBK
!
XY
q
twisted pair
twisted pair
16
Yellow
Pink
Yellow
Pink
Resolver S2
19
20
21
22
23
24
25
32
34
10
11
28
29
0.3sq
Resolver S2
0.3sq
ZR
w
twisted pair
twisted pair
S4
Purple
White
Blue/Red
S4
20
Purple
White
Blue/Red
S1
0.3sq
S1
21
22
23
24
25
32
34
0.3sq
RP
!
YP
o
twisted pair
twisted pair
S3
S3
R1
Orange/White 0.3sq
R1
R2
Orange/White 0.3sq
twisted pair
0.3sq
twisted pair
0.3sq
R2
DG
Green/White
Green
Green/White
Green
DG
Brown/White 0.3sq
Brown/White 0.3sq
Brake MB+
MB-
Brake MB+
MB-
YBK
!
RBK
!
twisted pair
twisted pair
Gray/White
Green
Gray/White
HLIM
GND24
HLIM
GND24
U
1
2
3
27
30
31
Red/White
Yellow/Black
Pink/Black
Green
Sensor
0.3sq
24V
ORG
!
Green
0.3sq
ORG
twisted pair
GND24
HLIM
10
11
28
29
2
2
1
2
3
0.75sq
0.75sq
0.75sq
XM
!
GND24
HLIM
GND24
U
V
2
3
4
1
2
3
4
3
4
1
2
3
4
XM
e
W
Green
FG Ring-tongue terminal
U
Yellow/Green 0.75sq
1
2
3
0.75sq
0.75sq
0.75sq
0.75sq
0.75sq
0.75sq
0.75sq
4
5
6
0.75sq
0.75sq
0.75sq
ZM
!
YM
!
2
3
3
V
V
YM
e
ZM
t
4
1
2
3
4
W
W
Ring-tongue terminal
4
1
2
3
4
Ring-tongue terminal
!
FG
U
Yellow/Green
FG
4
5
6
RM
@
RM
y
V
W
Ring-tongue terminal
@
FG
u
o
q
XP
o
XBK
YP
!
!
YBK
XY
!
!
ZP
w
ZBK
RP
!
!
RBK
ORG
ZR
!
!
e
r
XM
YM
XM
YM
t
y
!
ZM
RM
!
@
ZM
RM
@
4-axis robot cable
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Specifications
1-2
User I/O cable
The cartesian robot XY-X Series cable carrier type have a signal wire that can be
used freely from the X-axis wiring box to the final axis wiring box.
Signal
General-
purpose I/O
Connector NO
NO Connector
Remarks
Red
Part No.
Part name
SM connector
SMconnector
Contact
Part No.
SMR-10V-B
Qty.
1
I/O
q
1
2
1
2
I/O
w
1
2
3
4
5
White
Green
White
SMP-10V-BC
1
3
4
5
6
3
4
5
6
0.3sq
SYM-001T-0.6
SHF-001T-0.8BS
10
10
1
Yellow twisted pair
White
Blue
Contact
Cable
7
7
8
8
White
9
9
Purple
10
10
White
t
wr
qe
I/O
I/O
Controller side
Tool side
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed.
These can be used freely by the user.
Maker
J.S.T. Mfg Co., Ltd.
Connector type
SMR-10V-B
SMP-10V-BC
Pin SYM-001T-0.6
SHF-001T-0.8BS
Recommended crimping tool YC-122R
SMP-10-V-BC
SHF-001T-0.8BS
SMR-10-V-B
SYM-001T-0.6
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6
PXYX
1 Installation ..............................................................................6-1
1-1 Installation bolt types ....................................................................... 6-1
1-2 Installation bolt nominal length......................................................... 6-1
1-3 Tightening torque ............................................................................. 6-1
1-4 Installation methods ......................................................................... 6-2
2 Protective Connections...........................................................6-3
2-1 Ground terminal ............................................................................... 6-3
2-2 Ground wire ..................................................................................... 6-4
2-3 Wiring method.................................................................................. 6-4
3 Installing the Tool ....................................................................6-5
4 User Wiring and User Piping ..................................................6-6
5 Periodic Inspections ...............................................................6-8
5-1 Replenishing grease to the linear guide........................................... 6-8
5-2 Replenishing grease to the ball screw ............................................. 6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
To install the PXYX robot, tap holes into the installation base and secure the
robot to the base with M4 bolts from the inside of the robot.
1-1
1-2
Installation bolt types
• Use the following type of installation bolt.
Hexagon socket head Cap screw M4 Strength 8.8T
Installation bolt nominal length
!
CAUTION
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide's bearings and be damaged.
If the installation base is made of steel, secure 1D or more (4mm or more for M4)
for the screw fitting length. When using aluminum, secure 1.5D or more (6mm or
more for M4). The rail thickness is 5mm. (Refer to Fig. 6-1.)
Recommended nominal length
When installation base is made of steel
10mm or more
When installation base is made of aluminum 12mm or more
φ8
φ4.5
(42)
Fig. 6-1
1-3
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
·
·
·
·
Recommended torque
2.9N m to 4.4N m (30kgf cm to 45kgf cm)
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
1-4
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
!
CAUTION
Take care not to catch the shutter when installing the side covers.
1) Tap M4 coarse screw thread holes into the installation base where the robot is
to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Remove the M3 small screw fixing the X-axis side cover, and remove the
side cover.
3) Fix the robot onto the installation base with the designated bolt.
4) Return the side covers to the original state after installing the robot.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
2
Protective Connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground terminal
with the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground terminal is located on the end face of the X-axis wiring box. (Refer to
Fig. 6-2.)
Fig. 6-2
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
2-2
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
2-3
Wiring method
WARNING
Accurately insert the lock washer between the ring-tongue terminal and
robot.
Proper continuity may not be secured if the lock washer is dislocated.
Connect the ground wire to the ground terminal located on the end face of the X-
axis wiring box.
An M4 small screw with spring washer and lock washer are attached to the ground
terminal. Arrange the parts in the order of the lock washer, ring-tongue terminal
and M4 small screw with spring washer, and then tighten them. (Refer to Fig. 6-
3)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 6-3
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
3
Installing the Tool
WARNING
Always turn the controller power OFF before Installing a tool to prevent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
Four M4 coarse thread tap holes and two φ3 reamer holes are opened on the
Y-axis slider. (Refer to Fig. 6-4.) Install the user tool onto theY-axis slider using
these holes.
(90)
Y-axis
35
20 0.02
9
4-M4×0.7 Depth9
2-φ3H7 Depth6
Fig. 6-4
NOTE
The dimensions shown with (90) and (43) indicate the maximum outline dimen-
sions of the stainless cover covering the slider. The actual tool installation surface
is the shaded section shown above.
Select the screw under head length so that the fitting length of the screw fixing
the tool is 5mm or more, 9mm or less.
!
CAUTION
If the screw's fitting length is less than 5mm, the screw threads could be dam-
aged during tightening. If the fitting length exceeds 9mm, the screw end could
contact the cover and cause trouble.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
The methods for leading the wiring and piping to the tool are described in this
section.
A cable carrier is provided as a standard between the X-Y axes. Carry out wiring
and piping using this cable carrier.
1) Open the X-axis wiring box cover.
2) Rubber grommets are attached to the X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through.
3) Pass the cables and air tubes through the cable carrier.
These can be stored easily just by pressing on the outside of the cable carrier.
4) Open the Y-axis wiring box cover.
5) Rubber grommets are also attached to the Y-axis wiring box.
Open holes in these grommets, and pass the cables and air tubes through.
!
CAUTION
1. The wires could be damaged if the Insulock ties are tightened too much.
2. Manually move the robot by the full stroke before or after fixing to confirm
that the harness and air tube, etc., are not pulled in the cable carrier. These
could be damaged if pulled during operation.
6) When completed with the wiring, use the comb section at both ends of the
cable carrier, and fix the harness and air tubes with Insulock ties.
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
7) When completed with the wiring, reattach the cover to the wiring box.
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sectional
area.
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially by YAMAHA are shown below.
Power wire φ7.6
Signal wire φ8.2
50
62
Fig. 6-5
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
5
Periodic Inspections
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
5-1
Replenishing grease to the linear guide
Grease must be replenished to this linear guide periodically. Select the grease
from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the side cover. (Refer to 1-4. Installation.)
4) Apply grease onto the linear guide with a finger.
5) After greasing, return the side cover to the original position.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 PXYX
5-2
Replenishing grease to the ball screw
The X andY axes use a ball screw. Grease must be replenished to this ball screw
periodically. Select the grease from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the side cover. (Refer to 1-4. Installation.)
4) Apply grease onto the ball screw's shaft with a finger.
Wipe off any excessive grease.
5) After greasing, return the side cover to the original position.
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
6-10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 7
FXYX
1 Installation ..............................................................................7-1
1-1 Installation bolt types ....................................................................... 7-1
1-2 Installation bolt nominal length......................................................... 7-1
1-3 Tightening torque ............................................................................. 7-1
1-4 Installation methods ......................................................................... 7-2
2 Protective Connections...........................................................7-3
2-1 Ground terminal ............................................................................... 7-3
2-2 Ground wire ..................................................................................... 7-4
2-3 Wiring method.................................................................................. 7-4
3 Installing the Tool ....................................................................7-5
3-1 Arm type 2-axis model ..................................................................... 7-5
3-2 ZS (3rd-axis option) ......................................................................... 7-7
4 User Wiring and User Piping ..................................................7-8
4-1 Cable carrier type............................................................................. 7-8
4-1-1 Example of wiring and piping methods using cable carrier .............7-8
4-1-2 Cable carrier specifications ........................................................... 7-11
4-1-3 User I/O cable specifications .........................................................7-12
5 Periodic Inspections .............................................................7-13
5-1 Replenishing grease to the linear guide......................................... 7-13
5-2 Replenishing grease to the ball screw ........................................... 7-14
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
To install the FXYX robot, tap holes into the installation base and secure the
robot to the base with M6 bolts from the inside of the robot.
1-1
1-2
Installation bolt types
• Use the following type of installation bolt.
Hexagon socket head cap screw M6 Strength 8.8T
Installation bolt nominal length
!
CAUTION
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide’s bearings and be damaged.
If the installation base is made of steel, secure 1D or more (6mm or more for M6)
for the screw fitting length. When using aluminum, secure 1.5D or more (9mm or
more for M6). The frame thickness is 24mm. (Refer to Fig. 7-1.)
Recommended nominal length
35mm or more
Fig. 7-1
1-3
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
Recommended torque
9.8N·m to 12.7N·m (100kgf·cm to 130kgf·cm)
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
1-4
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
1) Tap M6 coarse screw thread holes into the installation base where the robot is
to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Fix the robot onto the installation base with the designated bolt from within
the clearance between the X-axis stroke cover and frame.
NOTE
Remove the stroke cover and carry out the work if it is difficult to install the
robot.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
2
Protective Connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground terminal
with the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground terminal is located on the end face of the X-axis wiring box. (Refer to
Fig. 7-2.)
X-axis wiring box
X-axis
Ground terminal
Fig. 7-2
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
2-2
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
2-3
Wiring method
WARNING
Accurately insert the lock washer between the ring-tongue terminal and
robot.
Proper continuity may not be secured if the lock washer is dislocated.
Connect the ground wire to the ground terminal located on the end face of the
X-axis wiring box.
An M4 small screw with spring washer and lock washer are attached to the ground
terminal. Arrange the parts in the order of the lock washer, ring-tongue terminal
and M4 small screw with spring washer, and then tighten. (Refer to Fig. 7-3)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 7-3
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
3
Installing the Tool
WARNING
Always turn the controller power OFF before Installing a tool to prevent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
3-1
Arm type 2-axis model
Eight M5 coarse thread tap holes and two φ5 reamer holes are opened on the
Y-axis slider. (Refer to Fig. 7-4.) Install the user tool onto theY-axis slider using
these holes.
M5 coarse thread tap holes are also opened on the slider side. Use these to fix
light loads other than the tool, such as a wiring retainer.
90
80
36
8-M5×0.8 Depth 8
20 (Tolerance between knock (0.02)
2-φ5H7Depth6
Y-axis
2-M5×0.8Depth10
(same on opposite side)
34
Fig. 7-4 Arm type
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
!
CAUTION
If the fitting length is less than 8mm, the threads could be damaged during
tightening. If the fitting length exceeds 12mm, the bolt end could contact the
bottom.
NOTE
There is a step on the top of the slider. The actual tool installation surface is the
shaded section shown above.
Select the nominal length of the tool fixing bolt so that the fitting length of the
screw fixing the tool is 8mm or more, 12mm or less.
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
3-2
ZS (3rd-axis option)
WARNING
Use the tap hole on the end of the shaft only to prevent the tool from
dislocating.
Do not use only this hole to install the tool. The tool could dislocate and
fly off the installation section during robot operation.
If the ZS unit is attached for the 3rd-axis, install the tool on the ZS shaft as shown
below. Use the φ12 section on the shaft, and fix the tool with a bolt coupling or
split clamp.
φ5
Hole for rotation stop tool
0
12
-0.018
M8×1.25 Depth15
Fig. 7-6 ZS
Hole
diameter
Bolt
Slit
Spline shaft
End effector or stay
Tap section
Fig. 7-7
Example : For split clamp
Recommended bolt M4 or more
Quantity
2 or more
Tightening torque
Hole diameter
4.5N·m (46kgfm)
φ12+0.018
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
4-1
Cable carrier type
A cable carrier is mounted as a standard between the X and Y axes. When using
three axes, a cable carrier is also provided between the Y and Z axes. Lay the
wiring and piping to the tool using these ducts. A 0.3sq 10-core flexible cable is
wired from the X-axis wiring box to the final axis' wiring box, and can be used
freely. (Refer to the "User wiring specifications" at the end of this section for
details.) The wiring and piping methods for a 2-axis arm type are explained be-
low as an example.
4-1-1
Example of wiring and piping methods using cable carrier
1) Remove the four M4 small screws and open the X-axis wiring box cover.
2) Rubber grommets are attached to the end face of X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through.
Grommet
3) Pass the cables and air tubes from the X-axis wiring box outlet through the
cable carrier.
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
The cable carrier has an outer lid that can be opened and closed easily. Use a
flat-tip screwdriver to open the lid. Press this lid in to close it. Open and close
this lid as necessary.
4) Remove the two M4 small screws on the Y-axis wiring box, and loosen two
places.
Loosen
Remove
(same on opposite side)
(same on opposite side)
5) Using the small screws loosened on theY-axis wiring box cover as a support
point, turn and open the box.
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
6) Remove the harness retainer from theY-axis wiring box. (Two hexagon socket
bolts M5)
Harness retainer
7)
!
CAUTION
1. The wires could be damaged if the harness retainer is tightened too much.
2. Manually move the robot by the full stroke before fixing to confirm that the
harness and air tube, etc., are not pulled in the cable carrier. These could be
damaged if pulled during operation.
Lay the required harness and air tubes, etc., in theY-axis box, and fix with the
harness retainer.
8) Assemble the wiring box cover at the original position.
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
4-1-2
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sectional
area.
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially by YAMAHA are shown below.
Cable carrier between X-Y
Cable carrier between Y-Z
2-axis I/O specifications
User I/O wire φ10.1
2-axis specifications
User I/O wire φ10.1
Power wire φ7.6
Signal wire φ8.2
50
62
57
73
3-axis specifications ZS
User I/O wire φ10.1
User I/O wire φ10.1
Power wire φ7.6
Signal wire φ8.2
Power wire φ9.8
Signal wire φ10.1
50
62
57
73
Fig. 7-8
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
4-1-3
User I/O cable specifications
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
With the cable carrier models, signal wires (0.3mm2 × 10 wires) that can be used
freely by the user are laid as a standard between the X-axis wiring box and final
axis' wiring box.
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed. Attach these to the user wiring to eliminate wiring led through
the robot.
Crimp the enclosed pins onto the user wiring, and insert into the connector.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
Refer to "1-2. User I/O wiring" in Chapter 5 "Specifications" for details on the
wiring specifications.
7-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
5
Periodic Inspections
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts, turn OFF the controller, wait for a while and check that
the part has cooled.
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
5-1
Replenishing grease to the linear guide
Grease must be replenished to this linear guide periodically. Select the grease
from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
X-axis, Y-axis
1) Turn the controller power OFF.
2) Place a sign indicating “Work In Progress” so that other operators do not turn
the controller power ON.
3) Remove the axis stroke cover when replenishing grease.
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
4) Using a grease gun, replenish grease from the grease nipple installed on the
linear guide bearings.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the linear guide bearings and rail.
The X-axis has four bearings, and the Y-axis has two bearings. Replenish
grease to all bearings.
Wipe off any excessive grease that has seeped out to the rail.
Recommended grease gun
MG70 (THK N-type nozzle)
5) After greasing, return the each cover to the original position.
5-2
Replenishing grease to the ball screw
The X-axis,Y-axis and Z-axis use a ball screw. Grease must be replenished to this
ball screw periodically. Select the grease from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
X-axis
!
CAUTION
Always remove the grease nipple after completing the work. Damage or
positional deviation could occur if the robot is operated with the grease nipple
installed.
1) Prepare the following recommended grease nipple beforehand.
Recommended grease nipple A-M6X1 type (JIS B1575)
7-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
2) Turn the controller power OFF.
3) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
4) Remove the stroke cover.
5) Install the grease nipple onto the ball screw flange.
6) Replenish the grease using the grease gun.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the ball screw nut and screw.
Wipe off any excessive grease.
Recommended grease gun
MG70 (THK N-type nozzle)
7) Remove the grease nipple.
8) Return the stroke cover to the original position.
Y-axis
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the stroke cover.
4) Apply grease to the ball screw shaft with a finger.
Wipe off any excessive grease.
5) Return the stroke cover to the original position.
7-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 FXYX
Z-axis (ZS)
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the screws (M4, 6 screws) fixing the cover, and pull the cover up-
ward and off.
M4 screw
M4 screw
Fig. 7-9 ZS
4) Wipe off any excessive grease adhered on the ball screw shaft and ball spline
shaft.
5) Apply a thin coat of grease on the screw shaft with a finger.
6) Return the cover to the original position.
7-16
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 8
SXYX
1 Installation ..............................................................................8-1
1-1 Installation bolt types ....................................................................... 8-1
1-2 Installation bolt nominal length......................................................... 8-1
1-3 Tightening torque ............................................................................. 8-2
1-4 Installation methods ......................................................................... 8-2
2 Protective Connections...........................................................8-5
2-1 Ground terminal ............................................................................... 8-5
2-2 Ground wire ..................................................................................... 8-6
2-3 Wiring methods ................................................................................ 8-6
2-3-1 Arm type with cable carrier ..............................................................8-7
2-3-2 Arm type with whipover cable, moving arm type, pole type ............8-9
2-3-3 XZ type ..........................................................................................8-10
3 Installing the Tool .................................................................. 8-11
3-1 Arm type, pole type 2-axis model....................................................8-11
3-2 Moving arm type 2-axis model ....................................................... 8-13
3-3 ZF
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 8-14
3-4 RF
(Arm type, moving arm type, 4th-axis option/XZ type 3rd-axis option)... 8-15
3-5 ZS/ZRS (Arm type 3/4-axis option, XZ type 2/3-axis model) ......... 8-16
3-6 ZFH (Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option ......................................................................... 8-17
3-7 ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 8-18
4 User Wiring and User Piping ................................................8-19
4-1 Cable carrier type........................................................................... 8-19
4-1-1 Example of wiring and piping methods using cable carrier ...........8-19
4-1-2 Cable carrier specifications ...........................................................8-22
4-1-3 User I/O cable specifications .........................................................8-23
4-2 Whipover cable type ...................................................................... 8-24
4-2-1 Examples of wiring and piping with whipover cable ......................8-24
5 Periodic inspections..............................................................8-26
5-1 Replenishing grease to the linear guide......................................... 8-26
5-2 Replenishing grease to the ball screw ........................................... 8-27
Download from Www.Somanuals.com. All Manuals Search And Download.
5-3 Periodic inspection of the ZS/ZRS unit .......................................... 8-29
5-3-1 Replenishing grease to the Z-axis ball screw and ball spline ........8-29
5-3-2 Adjusting the R-axis belt tension (ZRS) ........................................8-30
5-3-3 Replacing the R-axis harmonic drive (ZRS) ..................................8-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
The SXYX is installed with one of the following two methods.
Method A : Open through holes on the installation base and install with M6 bolts
from below.
(M6 tap holes are opened on the bottom of the robot.)
Method B : Tap holes into the installation base and secure the robot with M6
bolts from the inside of the robot.
1-1
1-2
Installation bolt types
• Use the following type of installation bolt.
Hexagon socket head cap screw M6 Strength 8.8T
Installation bolt nominal length
!
CAUTION
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide’s bearings and be damaged.
• When using method A, determine the nominal length so that the length of the
screw from the robot bottom is 9mm or more, 27mm or less. (Refer to right
side of Fig. 8-1.)
• When using method B, if the installation base is made of steel, secure 1D or
more (6mm or more for M6) for the installation base's screw fitting length.
When made of aluminum, secure 1.5D or more (9mm or more for M6). (Re-
fer to left side of Fig. 8-1.)
Fig. 8-1
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
1-3
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
.
.
.
.
Recommended torque
9.8N m to 12.7N m (100kgf cm to 130kgf cm)
1-4
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
■ Method A
1) Open a φ6.5 through hole on the installation base's robot installation surface.
2) Set the robot on the installation base and fix with M6 bolts from below.
Fig. 8-2
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
■ Method B
1) Tap M6 coarse screw thread holes into the installation base where the robot is
to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Remove the countersunk head screws (M4, 5 screws) fixing the X-axis stroke
cover.
When using the whipover cable for the arm type, pole type or moving arm
type, first loosen the small screws (M5, 2 screws) fixing the X-axis wiring
box. Then, slide the X-axis wiring box back and forth, and remove the coun-
tersunk head screws. (Refer to Fig. 8-3.)
Loosen (M5 small screw × 2 screws)
Fig. 8-3
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3) Remove the X-axis stroke cover.
If the cover is difficult to remove, manually move theY-axis to the motor side
stroke end. The cover will be easier to remove.
4) Fix the robot onto the installation base with the designated bolts.
5) After installing, return the stroke cover and X-axis wiring box to the original
positions.
!
CAUTION
If the X-axis wiring box was slid in step 2), install so that the end face of the
X-axis wiring box and end face of the X-axis are on the same plane. The X-axis
wiring box and frame bracket could interfere.
!
CAUTION
Take care not to catch the wiring when assembling the stroke cover.
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
2
Protective Connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground terminal
with the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground tap is located on the inside of the X-axis wiring box.
X-axis wiring box
Ground terminal
Fig. 8-4 Arm type with cable carrier
X-axis wiring box
Ground terminal
Fig. 8-5 XZ type with cable carrier
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
X-axis wiring box
Ground terminal
Fig. 8-6 Arm type, moving arm type,
gantry type with whipover cable specifications
2-2
2-3
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
Wiring methods
WARNING
Accurately insert the lock washer between the ring-tongue terminal and
robot.
Proper continuity may not be secured if the lock washer is dislocated.
!
CAUTION
Take care not to catch the harness and ground wire from the X-axis with the
cover of X-axis wiring box when installing the cover.
8-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
2-3-1
Arm type with cable carrier
1) Remove the four M4 small screws on the top of the X-axis wiring box, and
loosen the M4 small screw on the end face.
Remove
X-axis wiring box
Loosen
Fig. 8-7
2) Open the X-axis wiring box cover.
Lift up the back of the wiring box, push it forward and then pull it upward
and off. (Refer to Fig. 8-8.)
Fig. 8-8 Opening the wiring box
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3) Connect the ground wire to the ground terminal attached to the top of the
X-axis wiring box.
Ground terminal
Ground wire
An M4 small screw with spring washer and lock washer are attached to the
ground terminal.Arrange the parts in the order of the lock washer, ring-tongue
terminal and M4 small screw with spring washer, and then tighten. (Refer to
Fig. 8-9.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 8-9
4) Return the wiring box cover to the original position following steps 1 and 2
in reverse.
Lead out the ground wire from the user wiring outlet on the end face of the
X-axis wiring box.
8-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
2-3-2
Arm type with whipover cable, moving arm type, pole type
1) Remove the small screws (M4, 4 screws) fixing the X-axis wiring box cover,
and remove the cover. (Refer to Fig. 8-10.)
Remove the four M4 screws
Fig. 8-10
2) Fix the ring-tongue terminal of the ground wire to the ground terminal in the
X-axis wiring box.
An M4 small screw with spring washer and lock washer are attached to the
ground terminal.Arrange the parts in the order of the lock washer, ring-tongue
terminal and M4 small screw with spring washer, and then tighten. (Refer to
Fig. 8-11.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 8-11
3) Return the cover to the original position. Lead out the ground wire from the
user wiring outlet on the end face of the X-axis wiring box.
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
2-3-3
XZ type
1) Remove the small screws (M4, 4 screws) fixing the X-axis wiring box cover,
and remove the cover. (Refer to Fig. 8-12.)
Fig. 8-12
2) Fix the ring-tongue terminal of the ground wire to the ground terminal in the
X-axis wiring box.
An M4 small screw with spring washer and lock washer are attached to the
ground terminal.Arrange the parts in the order of the lock washer, ring-tongue
terminal and M4 small screw with spring washer, and then tighten. (Refer to
Fig. 8-13.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 8-13
3) Return the cover to the original position. Lead out the ground wire from the
user wiring outlet on the end face of the X-axis wiring box.
8-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3
Installing the Tool
WARNING
Always turn the controller power OFF before Installing a tool to prevent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
3-1
Arm type, pole type 2-axis model
Eight M6 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider. (Refer to Fig. 8-14 and Fig. 8-15.) Install the user tool onto the
Y-axis slider using these holes.
M5 coarse thread tap holes are also opened on the slider side. Use these to fix
light loads other than the tool, such as a wiring retainer.
2-φ6H7 Depth8
90
8 (Allowable screw depth)
6 (Thread insert depth)
70
32
8-M6×1.0 Depth8
50
4-M5×0.8 Depth7
Fig. 8-14 Arm type
8-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
23.5
19
2-φ6H7 Depth8
8-M6×1.0 Depth8
4-M5×0.8 Depth7
110
(Tolerance between knock (0.02)
135
20
20
90
Fig. 8-15 Pole type
!
CAUTION
If the fitting length is less than 6mm, the threads could be damaged during
tightening. If the fitting length exceeds 8mm, the bolt end could contact the
bottom.
NOTE
There is a step on the top of the slider. The actual tool installation surface is the
shaded section shown above.
Select the nominal length of the tool fixing bolt so that the fitting length of the
screw fixing the tool is 6mm or more, 8mm or less.(Refer to the cross-section
drawings in Fig. 8-14 and Fig. 8-15.)
8-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3-2
Moving arm type 2-axis model
For the moving arm type, an aluminum bracket is attached to the end of the
Y-axis. Install the tool on this bracket.
Twelve M6 coarse thread tap holes and two φ6 reamer holes are opened on the
bracket.
100
12-M6×1.0 through hole
15
70
5
34
32
44
29
2-φ6H7 Depth6
(Tap hole penetration)
50
17
10 (Plate thickness)
Fig. 8-16 Moving arm type
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the length of the bolt screw is 27mm or more from the installation
surface, the screw could contact the Y-axis.
Select the minimum fixing bolt screw length so that the screw fitting length is
9mm or more.
8-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3-3
ZF
(Arm type, moving arm type, 3rd-axis option/XZ type 2-
axis model)
When using the 3rd-axis model with ZF for the 3rd-axis, install the workpiece
onto the ZF slider in the following manner.
Four M5 coarse thread tap holes and a φ5 reamer hole are opened on the slider's
workpiece installation surface. Install the tool using these holes. Four M5 coarse
thread tap holes are opened on the slider side. Use these as required to fix light
loads other than the tool, such as the wiring retainer.
110
100
(Tolerance between knock (0.02)
10
9
9
4-M5×0.8 Depth9
4-M5×0.8 Depth12
2-φ5H7 Depth15
Stroke cover
Fig. 8-17 ZF
!
CAUTION
If the bolt fitting length is 12mm or more from the installation surface, the bolt
will contact the bottom.
Select the maximum nominal length of the tool fixing bolt so that the screw fit-
ting length is 12mm or less.
YAMAHA recommends a screw fitting length of 8mm or more.
8-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3-4
RF
(Arm type, moving arm type, 4th-axis option/XZ type 3rd-axis option)
!
CAUTION
Use the tap hole on the end face of the shaft only to prevent the tool from
dislocating.
Do not use only this hole to install the tool. The tool could dislocate and fly off
the installation section during robot operation.
When using the 4th-axis model with RF (rotary axis unit) for the 4th-axis, install
the tool onto the RF shaft in the following manner.
Use the φ20 section on the shaft, and fix the tool with a bolt coupling or split
clamp.
φ20h7
φ22
φ65h7
56.6
4-M6×1.0
Depth16
37.5
M8×1.25
Depth20
Fig. 8-18 RF
8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3-5
ZS/ZRS (Arm type 3/4-axis option, XZ type 2/3-axis model)
WARNING
Use the tap hole on the end of the shaft only to prevent the tool from
dislocating.
Do not use only this hole to install the tool. The tool could dislocate and
fly off the installation section during robot operation.
When the ZS or ZRS unit is attached to the 3rd or 4th-axis, install the tool onto
the ZS or ZRS shaft in the following manner. (The ZS and ZRS shaft have the
same shape.)
Use the φ12 section on the shaft, and fix the tool with a bolt coupling or split clamp.
φ5
Hole for rotation stop tool
0
12
-0.018
M8×1.25 Depth15
Fig. 8-19 ZS/ZRS
Hole
diameter
Bolt
Slit
Spline shaft
End effector or stay
Tap section
Fig. 8-20
Example : For split clamp
Recommended bolt M4 or more
Quantity
2 or more
Tightening torque
Hole diameter
4.5N·m (46kgfm)
φ12+0.018
8-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3-6
ZFH
(Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option
When using the 3rd-axis model with ZFH for the 3rd-axis, install the workpiece
onto the ZFH frame in the following manner.
Four M5 coarse thread tap holes and a φ5 reamer hole are opened on the frame's
workpiece installation surface. Install the tool using these holes. The tap depth is
9mm.
4-M5×0.8 Depth9
2-φ5H7 Depth8
A
A
70
(Tolerance between knock (0.02)
31
28
31
SEC A-A
-
Fig.8-21 Tool installation ZFH
NOTE
There is a step on the ZFH frame.
The actual tool installation surface is the shaded section shown above.
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the screw length exceeds 27mm from the installation surface, the
screw could contact the bottom.
8-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3-7
ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-
axis model)
When using the 3rd-axis model with ZFL for the 3rd-axis, install the workpiece
onto the ZFL slider in the following manner.
Six M5 coarse thread tap holes and a φ5 reamer hole are opened on the slider's
workpiece installation surface. Install the tool using these holes. Six M5 coarse
thread tap holes are opened on the slider side. Use these as required to fix light
loads other than the tool, such as the wiring retainer.
110
10
6-M5×0.8 Depth9
100
(Tolerance between knock (0.02)
2-φ5H7 Depth15
6-M5×0.8 Depth12
9
9
Stroke cover
Fig. 8-22 ZFL
Select the maximum nominal length of the tool fixing bolt so that the screw fit-
ting length is 12mm or less.
YAMAHA recommends a screw fitting length of 8mm or more.
!
CAUTION
If the bolt fitting length is 12mm or more from the installation surface, the bolt
will contact the bottom.
8-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
4-1
Cable carrier type
A cable carrier is mounted as a standard between the X and Y axes. When 3rd-
axis are used, a cable carrier is also provided between theY and Z axes, and when
using 4th-axis, a cable carrier is also provided between the Z and R axes. Lay the
wiring and piping to the tool using these ducts. A 0.3sq 10-core flexible cable is
wired from the X-axis wiring box to the final axis' wiring box, and can be used
freely. (Refer to the "User wiring specifications" at the end of this section for
details.) The wiring and piping methods for a 2-axis arm type are explained be-
low as an example.
4-1-1
Example of wiring and piping methods using cable carrier
1) Open the X-axis wiring box cover. Refer to section "2-3-1 Arm type with
cable carrier" for details on opening the cover.
2) Remove the harness retainer located at the cable carrier outlet. (Hexagon
socket bolt M5, 2 bolts)
Harness retainer
8-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
3) Pass the cables and air tubes through the cable carrier. The cable carrier has
an outer lid that can be opened and closed easily. Use a flat-tip screwdriver to
open the lid. Press this lid in to close it. Open and close this lid as necessary.
4) Open the Y-axis wiring box cover.
5) There is a harness retainer also in the Y-axis box. Remove this, and lay out
the wires in the Y-axis box.
6)
!
CAUTION
1. The wires could be damaged if the harness retainer is tightened too much.
2. Manually move the robot by the full stroke before fixing to confirm that the
harness and air tube, etc., are not pulled in the cable carrier. These could be
damaged if pulled during operation.
After leading all wires, fix the wires with the harness retainer.
8-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
7)
!
CAUTION
Take care not to catch the harness or air tube with the cover when installing the
covers.
Assemble the wiring box cover at the original position.
Wire lead-out port
Wire protection
material
State with cover installed
Pass the X-axis wiring
through this notch.
Lay out the wires on
the protection material.
State of X-axis wiring box
when wiring is completed
8-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
4-1-2
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sec-
tional area.
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially byYAMAHA are shown below.
2-axis specifications X-Y cable carrier
2-axis I/O specifications Y-axis cable carrier
User I/O wire φ10.1
Power wireφ7.6
Signal wire φ8.2
User I/O wire φ10.1
77
93
57
73
3-axis specifications X-Y cable carrier
XZ type 2-axis specifications X-Z cable carrier
3-axis specifications Y-Z cable carrier
User I/O wire φ10.1
User I/O wire φ10.1
Power wire φ9.8
Power wire φ7.6
Signal wire φ10.1
Signal wire φ8.2
77
93
57
73
4-axis specifications X-Y cable carrier
XZ type 3-axis specifications X-Z cable carrier
4-axis specifications Y-Z cable carrier
Signal wire φ11
User I/O wire φ11
Power wire φ7.6
Power wire φ9.8
Power wire φ9.8
Signal wire φ10.1
Signal wire φ11
User I/O wire φ10.1
77
93
57
73
4-axis specifications
Z-R cable carrier
Power wire φ7.6
Signal wire φ10.1
Power wire φ7.6
Signal wire φ11
Power wire φ9.8
(ZFH)
(ZRFL)
(ZRFH)
Signal wire φ8.2
57
73
57
73
57
73
Fig. 8-23
8-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
4-1-3
User I/O cable specifications
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
With the cable carrier model, signal wires (0.3mm2 × 10 wires) that can be used
freely by the user are laid as a standard between the X-axis wiring box and final
axis' wiring box.
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed. Attach these to the user wiring to eliminate wiring led through
the robot.
Crimp the enclosed pins onto the user wiring, and insert into the connector.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
Refer to "1-2. User I/O wiring" in Chapter 5 "Specifications" for details on the
wiring specifications.
8-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
4-2
Whipover cable type
!
CAUTION
Do not clamp the wires or tubes to the outside of the independent cable. The
independent cable could sag or break and ultimately be disconnected.
The signal wires (0.3mm2 × 7 wires) and air tubes (4 × 2.5, 2 tubes) are incorpo-
rated in the whipover cable. Use these to wire and pipe to the tool.
Signal Connector NO
NO Connector Remarks
Part No.
Part name
SM connector
SM connector
Contact
Part No.
SMR-10V-B
Qty.
1
General-
purpose
I/O
I/O
q
1
2
3
1
2
I/O
w
Brown
Red
1
2
3
4
5
3
4
Orange
Blue
SMP-10V-BC
1
4
5
6
7
SYM-001T-0.6
SHF-001T-0.8BS
7
5
6
Purple
Gray
Contact
7
Cable
1
7
White
8
8
9
9
10
10
P
P
BK
I/O
BK
I/O
t
qe
wr
ORG
ORG
M
M
Air tube
Air tube
Tool side
Controller side
Fig. 8-24 Whipover cable user-wire specifications
4-2-1
Examples of wiring and piping with whipover cable
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
1) Crimp the enclosed connector onto the user cable.
Refer to section “1-2. User I/O wire” in Chapter 5 “Specifications” for de-
tails on the enclosed connector and pin specifications.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
8-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
2) When using an air tube, prepare an air coupler for connecting the user air
tube with the YAMAHA air tube.
3) Open the X-axis wiring box cover.
Fig. 8-25
4) Place the required cables and air tubes, etc., in the X-axis wiring box. Crimp
the enclosed connectors onto the cable beforehand.
5) Connect the connectors, and connect the air tubes with the air couplers.
6) Open the Y-axis wiring box cover.
7) Open holes (or notches) in the rubber grommets attached to the cover, and set
the required cables and air tubes, etc., in the Y-axis wiring box. Crimp the
enclosed connectors onto the user cables beforehand.
8) Connect the connectors in the same manner as the X-axis, and connect the air
tubes with the air couplers.
9)
!
CAUTION
Take care not to catch the wiring or air couplers when installing the covers.
When completed with all wiring work, return each wiring box cover to the
original positions. Sandwich the X-axis wiring and air tube with the protec-
tive material at the wire lead-out port of each wiring box.
8-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
5
Periodic inspections
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts, turn OFF the controller, wait for a while and check that
the part has cooled.
5-1
Replenishing grease to the linear guide
Grease must be replenished to this linear guide periodically. Select the grease
from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
NOTE
When the ZF unit is attached for the 3rd-axis, the replenishment work can be
carried out easier by moving the Z-axis slider to near the motor (near the origin)
and turning the controller power OFF.
2) Place a sign indicating “Work In Progress” so that other operators do not turn
the controller power ON.
3) Remove the axis stroke cover when replenishing grease. (Refer to section "1.
Installation" for details on removing the X-axis cover.)
8-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
4) Using a grease gun, replenish grease from the grease nipple installed on the
linear guide bearings.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the linear guide bearings and rail.
X-axis, Y-axis
The X-axis and Y-axis each have four linear guide bearings. Replenish grease to
all four bearings.
Wipe off any excessive grease that has seeped out to the rail.
Z-axis (ZF)
One linear guide bearing is attached. A grease nipple is attached to the counter-
motor side of the slider, so move the slider to the motor side and then start the
work.
5) Install the stroke cover.
6) Confirm the surrounding safety, and then turn the controller power ON.
5-2
Replenishing grease to the ball screw
The X-axis,Y-axis and Z-axis use a ball screw. Grease must be replenished to this
ball screw periodically. Refer to section 5-3-1. for details on replenishing the
grease to the ZS/ZRS unit ball screw. Select the grease from the following recom-
mended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
8-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
!
CAUTION
Always remove the grease nipple after completing the work. Damage or
positional deviation could occur if the robot is operated with the grease nipple
installed.
1) Prepare the following recommended grease nipple beforehand.
Recommended grease nipple A-M6X1 type (JIS B1575)
2) Turn the controller power OFF.
NOTE
When the ZF unit is attached for the 3rd-axis, the replenishment work can be
carried out easier by moving the Z-axis slider to near the motor (near the origin)
and turning the controller power OFF.
3) Place a sign indicating “Work In Progress” so that other operators do not turn
the controller power ON.
4) Remove the stroke cover of the axis to which grease is to be replenished.
(Refer to section "1. Installation" for details on removing the X-axis cover.)
5) Install the grease nipple onto the ball screw flange.
6) Using a grease gun, replenish grease from the grease nipple.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the ball screw nut and screw.
Wipe off any excessive grease.
Recommended grease
: Alvania No. 2 (Showa Shell)
: Daphne Eponex No. 2 (Idemitsu)
Recommended grease gun : MG70 (THK N-type nozzle)
7) Remove the grease nipple.
8-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
5-3
Periodic inspection of the ZS/ZRS unit
5-3-1
Replenishing grease to the Z-axis ball screw and ball spline
A ball screw drive is used for the ZS and ZRS vertical axis. Grease must be
replenished to this ball screw periodically. Select the grease from the following
recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the screws (M4, 6 screws) fixing the cover, and pull the cover up-
ward and off.
M4 screw
M4 screw
Fig. 8-26 ZS
4) Wipe off any excessive grease adhered on the ball screw shaft and ball spline
shaft.
5) Apply a thin coat of grease on the screw shaft with a finger.
6) Return the cover to the original position.
8-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
5-3-2
Adjusting the R-axis belt tension (ZRS)
With the ZRS model, a timing belt is used for the R-axis.
If the timing belt tension is week, adjust the belt tension with the following pro-
cedures.
WARNING
There is a risk of injury if fingers, etc., are caught between the drive sec-
tion pulley and belt section. Always turn the controller power OFF and
carefully carry out the work if these parts may be contacted.
!
CAUTION
The position will deviate when the belt tension is adjusted.
Carry out absolute reset, and reset the basic coordinates and point data.
Push-pull scale
Deflection
Load
Pulley
Belt
Pulley
Fig. 8-27 Adjusting the belt tension
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the cover. (M4, 6 screws)
4) The following work must be carried out by two operators.
One operator must apply a vertical load on the center of the belt with the
push-pull scale, and the other operator must measure the belt deflection at
that time.
5) If the measured value is within the range shown below, there is no need for
adjustment. Adjust with the following procedure if the measured value is not
within the range.
Table 8-1
Load
4.4 to 4.8N ( 0.45 to 0.49kgf )
2mm
Deflection amount
6) Loosen the M4 bolt q (three positions) shown in Fig. 8-28.
8-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
7) If the value measured in step 4) is smaller than the value given in Table 8-1,
move the R-axis motor so that the tension increases. If larger than the value
in Table 8-1, move the R-axis motor so that the tension decreases. Then, fix
the bolts.
8) Measure the belt tension again with the procedure given in step 4).
If the measured value is within the range shown in Table 8-1, adjustment of
the R-axis belt tension is completed. If the measured value is not within the
range shown in Table 8-1, repeat steps 6) to 8) and adjust.
9) Tighten the M4 bolt q with the specified tightening torque.
.
.
Specified torque
4.5N m (46kgf cm)
10) Return the cover to the original position.
Tension decreases
qR-axis motor fixing bolt (M4)
Tension increases
R-axis motor
Fig. 8-28 ZRS belt tension
5-3-3
Replacing the R-axis harmonic drive (ZRS)
The ZRS R-axis speed reduction gear uses a harmonic drive.
The ZRS uses a harmonic drive as the R-axis speed reduction gear, which must
be replaced after using for a set period. Determine the harmonic drive replace-
ment period with the following procedure, and replace as required.
The ZRS harmonic grease uses a long-life type, and the grease does not need to
be replaced.
8-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 SXYX
Replacement period
The harmonic drive replacement period is determined by the total number of
wave generator rotations. A calculation example is shown below.
The recommended harmonic drive replacement period is 8.4×108 rotations (at
usage atmospheric temperature range 0°C to +40°C).
The harmonic drive should be replaced earlier if the robot operation duty is high
or if the temperature conditions are poor.
[Replacement period]
=8.4×108/(n×60×h×D×N×θ) years
n
θ
N
h
: Number of robot movements in one minute
: Average axis rotation in one movement
: Deceleration rate (50 for ZRS R-axis)
: Number of operation hours per day
: Number of operation days per year
D
(Example) TheYK500X X-axis harmonic drive replacement period when the
axis rotates an average quarter turn every movement and the robot
moves ten times in one minute. (Operation hours: 24 hours/day,
number of operation days: 240 days/year)
n
: 10
θ
: 0.25
N
: 50
h
: 24
D
: 240
[Replacement period]
=8.4×108/(n×60×h×D×N×θ)
=8.4×108/(10×60×24×240×50×0.25)
=19.4 years
Consult with YAMAHA when actually replacing the harmonic drive.
8-32
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 9
MXYX
1 Installation ..............................................................................9-1
1-1 Installation bolt types ....................................................................... 9-1
1-2 Installation bolt nominal length......................................................... 9-1
1-3 Tightening torque ............................................................................. 9-1
1-4 Installation methods
(Arm type, moving arm type, pole type, gantry type X-axis) ............ 9-2
1-5 Installation methods (Gantry type support axis)............................... 9-4
2 Protective Connections...........................................................9-5
2-1 Ground terminal ............................................................................... 9-5
2-2 Ground wire ..................................................................................... 9-5
2-3 Wiring methods ................................................................................ 9-6
3 Installing the Tool ....................................................................9-7
3-1 Arm type, pole type 2-axis model..................................................... 9-7
3-2 Moving arm type 2-axis model ......................................................... 9-9
3-3 ZF
(Arm type, moving arm type, gantry type 3rd-axis option) ............. 9-10
3-4 RF
(Arm type, moving arm type, 4th-axis option/XZ type 3rd-axis option)... 9-11
3-5 ZFH (Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option ......................................................................... 9-12
3-6 ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 9-13
4 User Wiring and User Piping ................................................9-14
4-1 Cable carrier type........................................................................... 9-14
4-1-1 Example of wiring and piping methods using cable carrier ...........9-14
4-1-2 Cable carrier specifications ...........................................................9-17
4-1-3 User I/O cable specifications .........................................................9-18
4-2 Whipover cable type ...................................................................... 9-19
4-2-1 Examples of wiring and piping with Whipover cable .....................9-19
5 Periodic Inspections .............................................................9-21
5-1 Replenishing grease to the linear guide......................................... 9-21
5-2 Replenishing grease to the ball screw ........................................... 9-22
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
Install the MXYX by tapping holes into the installation base and securing the
robot to the base with M8 bolts from the inside of the robot.
1-1
1-2
Installation bolt types
• Use the following type of installation bolt.
Hexagon socket head cap screw M8 Strength 8.8T
Installation bolt nominal length
!
CAUTION
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide’s bearings and be damaged.
If the installation base is made of steel, secure 1D or more (8mm or more for M8)
for the screw fitting length. When made of aluminum, secure 1.5D or more (12mm
or more for M8).
The frame thickness is 26.5mm. (Refer to Fig. 9-1.)
Recommended nominal length
When installation base is made of steel
35mm or more
When installation base is made of aluminum 40mm or more
Fig. 9-1
1-3
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
Recommended torque
22.5N·m to 36.3N·m (230kgf·cm to 370kgf·cm)
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
1-4
Installation methods
(Arm type, moving arm type, pole type, gantry type X-axis)
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
1) Tap M8 coarse screw thread holes into the installation base where the robot is
to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Loosen the small screws (M5, 4 screws) fixing the X-axis wiring box. The
wiring box can be slid along the T slot when these screws are loosened. (Re-
fer to Fig. 9-2.)
Fig. 9-2
3) Remove the countersunk head screws fixing the X-axis stroke cover. (M4
countersunk head screw, 6 screws)
Fig. 9-3 MXY X-axis
!
CAUTION
The screws indicated with an asterisk (*) in the above drawing should be re-
moved from the wiring clearance after sliding the X-axis wiring box. Take care
not to damage the wires at this time. (Refer to Fig. 9-4.)
Fig. 9-4
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
4) Remove the stroke cover.
If the cover is difficult to remove, manually move theY-axis to the motor side
stroke end. The cover will be easier to remove.
If the X-axis stroke is 550mm or less, remove the X-axis wiring box before
removing the stroke cover.
5) Fix the robot onto the installation base with the designated bolts.
6) After installing, return the stroke cover and X-axis wiring box to the original
positions.
!
CAUTION
Always install the X-axis wiring box at the original position. The amount of pro-
jection from the cable carrier’s stroke end could change, or the cable carrier
and Y-axis bracket could contact. (Refer to Fig. 9-5.)
10
Fig. 9-5 MXY box position
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
1-5
Installation methods (Gantry type support axis)
The MXYX and HXYX gantry types have a guide rail for support on the Y-axis
end so that heavy loads can be handled. When installing, take care to the parallel-
ism of the X-axis and guide rail and to the difference in height from the installa-
tion surface.
If the distance between the X-axis and guide rail is within 5mm, it can be changed
or adjusted. The procedures are given below.
!
CAUTION
Move the X-axis as much as possible, and tighten the bolts where the move-
ment is the lightest.
Set the X-axis and guide rail parallelism during installation. Make sure that
there is no difference in the height direction of the X-axis and guide rail installa-
tion surface.
1) Fix the robot onto the specified position of the installation base with bolts.
Do not tighten the guide rail bolt at this time. Securely fix the X-axis section
onto the installation base.
2) When the ZR-axis is provided, or if tools are already attached, move as
close to the X-axis side as possible so that a load is not applied on the
guide rail.
3) Loosen the bolt for theY-axis and support installation bracket. (Refer to
following drawing.)
4) Temporarily fix the guide rail onto the installation base with bolts.
The parallelism of the guide rail and X-axis must be set using a dial gauge or
pick gauge, etc.
5) To easily set the parallelism, first tighten the bolt loosened in step 3).
Set the X-axis near one end, and tighten the bolt on the guide rail end in this
state. Next, move the X-axis to the opposite end, and tighten the bolt on the
opposite side of the guide rail in this state. Repeat this until all bolts have
been tightened.
Y-axis
Support installation bracket
Guide rail stay
Bolts
Adjustment of gantry type support rail
9-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
2
Protective Connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground tap with
the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground terminal is located on the inside of the X-axis wiring box.
X-axis wiring box
Ground terminal
Fig. 9-6
2-2
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
2-3
Wiring methods
!
CAUTION
Be sure to insert the lock washer between the ring-tongue terminal and robot in
step3 below.
Proper continuity may not be secured if the lock washer is dislocated.
1) Loosen the four M4 small screws, and open the X-axis wiring box cover.
2) Open holes (or notches) in the grommets on the end face of the X-axis wiring
box, and pass the ground wire through.
Ground wire
3) Connect the ring-tongue terminal of the ground wire to the ground terminal
on the robot.
An M4 small screw with spring washer and lock washer are attached to the ground
terminal . Arrange the parts in the order of the lock washer, ring-tongue terminal
and M4 small screw with spring washer, and then tighten. (Refer to Fig. 8-9.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 9-7
4) Return the X-axis wiring box cover to the original position.
9-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3
Installing the Tool
Install the user tool onto the robot’s tool installation surface in the following
manner.
WARNING
Always turn the controller power OFF before Installing a tool to prevent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
3-1
Arm type, pole type 2-axis model
Eight M6 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider installation surface. (Refer to Fig. 9-8 and Fig. 9-9.) Install the user
tool onto the Y-axis slider using these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these to
fix light loads other than the tool, such as a wiring retainer.
!
CAUTION
If the fitting length is less than 6mm, the threads could be damaged during
tightening. Note that if the fitting length exceeds 8mm, the bolt end could con-
tact the cover.
NOTE
There is a step on the top of the slider. The actual tool installation surface is the
shaded section shown above.
Select the nominal length of the tool fixing bolt so that the fitting length of the
screw fixing the tool is 6mm or more, 8mm or less.(Refer to the cross-section
drawings in Fig. 9-8 and Fig. 9-9.)
9-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
140
124
70
8 (Allowable screw depth)
6 (Thread insert depth)
2-φ6H7 Depth8
8-M6×1.0 Depth8
4-M5×0.8 Depth7
50
45
Fig. 9-8 Arm type, gantry type
23.5
19
2-φ6H7 Depth8
4-M5×0.8 Depth7
8-M6×1.0 Depth8
110
(Tolerance between knock (0.02)
135
20
90
20
Fig. 9-9 MXYX pole type
9-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3-2
Moving arm type 2-axis model
For the moving arm type, an aluminum bracket is attached to the end of the
Y-axis. Install the tool on this bracket.
Twelve M6 coarse thread tap holes and two φ6 reamer holes are opened on the
bracket.
100
70
44
2-φ6H7 Depth6
12-M6×1.0
32
20
10
Fig. 9-10 Moving arm type
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the length of the bolt screw is 30mm or more from the installation
surface, the screw could contact the Y-axis.
Select the minimum fixing bolt screw length so that the screw fitting length is
9mm or more.
9-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3-3
ZF
(Arm type, moving arm type, gantry type 3rd-axis option)
When using the 3rd-axis model with ZF for the 3rd-axis, install the workpiece
onto the ZF slider in the following manner.
Four M5 coarse thread tap holes and a φ5 reamer hole are opened on the slider's
workpiece installation surface. Install the tool using these holes. Four M5 coarse
thread tap holes are opened on the slider side. Use these as required to fix light
loads other than the tool, such as the wiring retainer.
110
100
(Tolerance between knock (0.02)
10
9
9
4-M5×0.8 Depth9
4-M5×0.8 Depth12
2-φ5H7 Depth15
Stroke cover
Fig. 9-11 ZF
!
CAUTION
If the bolt fitting length is 12mm or more from the installation surface, the bolt
will contact the bottom.
Select the maximum nominal length of the tool fixing bolt so that the screw fit-
ting length is 12mm or less.
YAMAHA recommends a screw fitting length of 8mm or more.
9-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3-4
RF
(Arm type, moving arm type, 4th-axis option/XZ type 3rd-axis option)
!
CAUTION
Use the tap hole on the end face of the shaft only to prevent the tool from
dislocating.
Do not use only this hole to install the tool. The tool could dislocate and fly off
the installation section during robot operation.
When using the 4th-axis model with RF (rotary axis unit) for the 4th-axis, install
the tool onto the RF shaft in the following manner.
Use the φ20 section on the shaft, and fix the tool with a bolt coupling or split
clamp.
φ20h7
φ22
φ65h7
56.6
4-M6X1.0
Depth16
37.5
M8×1.25
Depth20
Fig. 9-12 RF
9-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3-5
ZFH
(Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option
When using the 3rd-axis model with ZFH for the 3rd-axis, install the workpiece
onto the ZFH frame in the following manner.
Four M5 coarse thread tap holes and a φ5 reamer hole are opened on the frame's
workpiece installation surface. Install the tool using these holes. The tap depth is
9mm.
4-M5×0.8 Depth9
2-φ5H7 Depth8
A
A
70
(Tolerance between knock (0.02)
31
28
31
SEC A-A
Fig. 9-13 Tool installation ZFH
NOTE
There is a step on the ZFH frame.
The actual tool installation surface is the shaded section shown above.
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the screw length exceeds 27mm from the installation surface, the
screw could contact the bottom.
9-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3-6
ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-
axis model)
When using the 3rd-axis model with ZFL for the 3rd-axis, install the workpiece
onto the ZFL slider in the following manner.
Six M5 coarse thread tap holes and a φ5 reamer hole are opened on the slider's
workpiece installation surface. Install the tool using these holes. Six M5 coarse
thread tap holes are opened on the slider side. Use these as required to fix light
loads other than the tool, such as the wiring retainer.
110
10
6-M5×0.8 Depth9
100
(Tolerance between knock (0.02)
2-φ5H7 Depth15
6-M5×0.8 Depth12
9
9
Stroke cover
Fig. 9-14 ZFL
Select the maximum nominal length of the tool fixing bolt so that the screw fit-
ting length is 12mm or less.
YAMAHA recommends a screw fitting length of 8mm or more.
!
CAUTION
If the bolt fitting length is 12mm or more from the installation surface, the bolt
will contact the bottom.
9-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
4-1
Cable carrier type
A cable carrier is mounted as a standard between the X and Y axes. When 3rd-
axis are used, a cable carrier is also provided between theY and Z axes, and when
using 4th-axis, a cable carrier is also provided between the Z and R axes. Lay the
wiring and piping to the tool using these ducts. A 0.3sq 10-core flexible cable is
wired from the X-axis wiring box to the final axis' wiring box, and can be used
freely. The wiring and piping methods for a 2-axis arm type are explained below
as an example.
4-1-1
Example of wiring and piping methods using cable carrier
1) Remove the four M4 small screws and open the X-axis wiring box cover.
2) Rubber grommets are attached to the end face of X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through.
9-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
3) Remove the harness retainer located at the cable carrier outlet. (Hexagon
socket bolt M5, 2 bolts)
Harness retainer
4) Pass the required wires and pipes through the cable carrier.
The cable carrier has an outer lid that can be opened and closed easily. Use a
flat-tip screwdriver to open the lid. Press this lid in to close it.
5) Open the Y-axis wiring box cover, and lay the required wiring and piping.
6)
!
CAUTION
1. The wires could be damaged if the harness retainer is tightened too much.
2. Manually move the robot by the full stroke before fixing to confirm that the
harness and air tube, etc., are not pulled in the cable carrier. These could be
damaged if pulled during operation.
When completed with the wiring, fix with the harness retainer in the wiring box.
7)
!
CAUTION
Take care not to catch the harness or air tube with the cover.
Return each wiring box cover to the original position.
9-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
4-1-2
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sec-
tional area. (This ratio is called the cable carrier space factor.)
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially byYAMAHA are shown below.
2-axis specifications X-Y cable carrier
2-axis I/O specifications Y-axis cable carrier
User I/O wire φ10.1
Power wire φ7.6
Signal wire φ8.2
User I/O wire φ10.1
77
93
57
73
3-axis specifications X-Y cable carrier
3-axis specifications Y-Z cable carrier
User I/O wire φ10.1
User I/O wire φ10.1
Power wire φ9.8
Power wire φ7.6
Signal wire φ10.1
Signal wire φ8.2
77
93
57
73
4-axis specifications X-Y cable carrier
4-axis specifications Y-Z cable carrier
Signal wire φ11
User I/O wire φ10.1
Power wire φ9.8
Power wire φ7.6
Power wire φ9.8
Signal wire φ10.1
Signal wire φ 11
User I/O wire φ10.1
77
93
57
73
XZ type 3-axis specifications Z-R cable carrier
4-axis specifications Z-R cable carrier
Signal wire φ10.1
Power wire φ7.6
Signal wire φ8.2
Signal wire φ11
Power wire φ9.8
(ZRFL)
(ZRFH)
Power wire φ7.6
(ZFH)
57
73
57
73
57
73
Fig. 9-15
9-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
4-1-3
User I/O cable specifications
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
With the cable carrier model, signal wires (0.3mm2 × 10 wires) that can be used
freely by the user are laid as a standard between the X-axis wiring box and final
axis' wiring box.
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed. Attach these to the user wiring to eliminate wiring led through
the robot.
Crimp the enclosed pins onto the user wiring, and insert into the connector.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
Refer to "1-2. User I/O wiring" in Chapter 5 "Specifications" for details on the
wiring specifications.
9-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
4-2
Whipover cable type
!
CAUTION
Do not clamp the wires or tubes to the outside of the independent cable. The
independent cable could sag or break and ultimately be disconnected.
The signal wires (0.3mm2 × 7 wires) and air tubes (4 × 2.5, 2 tubes) are incorpo-
rated in the Whipover cable. Use these to wire and pipe to the tool.
Signal Connector NO
NO Connector Remarks
Part No.
Part name
SM connector
SM connector
Contact
Part No.
SMR-10V-B
Qty.
1
General-
purpose
I/O
I/O
q
1
2
3
1
2
I/O
w
Brown
Red
1
2
3
4
5
3
4
Orange
Blue
SMP-10V-BC
1
4
5
6
7
SYM-001T-0.6
SHF-001T-0.8BS
7
5
6
Purple
Gray
Contact
7
Cable
1
7
White
8
8
9
9
10
10
P
P
BK
I/O
BK
I/O
t
qe
wr
ORG
ORG
M
M
Air tube
Air tube
Tool side
Controller side
Fig. 9-16 Whipover cable user-wire specifications
4-2-1
Examples of wiring and piping with Whipover cable
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
1) Crimp the user's cable and tool wiring onto the enclosed connector.
Refer to section “1-2. User I/O wire” in Chapter 5 “Specifications” for de-
tails on the enclosed connector and pin specifications.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
9-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
2) When using an air tube, prepare an air coupler for connecting the user air
tube with the YAMAHA air tube.
3) Open the X-axis wiring box cover.
Fig. 9-17
4) Rubber grommets are attached to the X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through. Crimp the enclosed connectors onto the cables.
5) Connect the connectors, and connect the air tubes using the air couplers.
6) Open the Y-axis wiring box cover.
7) Rubber grommets are also attached to the Y-axis wiring box.
Open holes in these grommets, and pass the tool side cables and air tubes
through.
8) Connect the connectors in the same manner as the X-axis, and connect the air
tubes with the air couplers.
!
CAUTION
Take care not to catch the wiring or air couplers when installing the covers.
9) When completed with all wiring work, return each wiring box cover to the
original positions. Sandwich the X-axis wiring and air tube with the protec-
tive material at the wire lead-out port of each wiring box.
9-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
5
Periodic Inspections
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts, turn OFF the controller, wait for a while and check that
the part has cooled.
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
5-1
Replenishing grease to the linear guide
Grease must be replenished to this linear guide periodically. Select the grease
from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
NOTE
When the ZF unit is attached for the 3rd-axis, the replenishment work can be
carried out easier by moving the Z-axis slider to near the motor (near the origin)
and turning the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the axis stroke cover when replenishing grease.
9-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
4) Using a grease gun, replenish grease from the grease nipple installed on the
linear guide bearings.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the linear guide bearings and rail.
The X-axis andY-axis each have four linear guide bearings. Replenish grease
to all four bearings.
Wipe off any excessive grease that has seeped out to the rail.
Recommended grease gun : MG70 (THK H-type nozzle)
5) Return the stroke cover to the original position.
5-2
Replenishing grease to the ball screw
The X-axis,Y-axis and Z-axis use a ball screw. Grease must be replenished to this
ball screw periodically. Select the grease from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
!
CAUTION
Always remove the grease nipple after completing the work. Damage or
positional deviation could occur if the robot is operated with the grease nipple
installed.
1) Prepare the following recommended grease nipple beforehand.
Recommended grease nipple A-M6X1 type (JIS B1575)
9-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 MXYX
2) Turn the controller power OFF.
NOTE
When the ZF unit is attached for the 3rd-axis, the replenishment work can be
carried out easier by moving the Z-axis slider to near the motor (near the origin)
and turning the controller power OFF.
3) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
4) Remove the stroke cover of the axis to which grease is to be replenished.
5) Install the grease nipple on the M6 tap on the ball screw flange surface.
6) Using a grease gun, replenish grease from the grease nipple.
Sufficient grease has been replenished when new grease starts to seep out to
the screw shaft.
Wipe off any excessive grease.
Recommended grease gun : MG70 (THK H-type nozzle)
7) Remove the grease nipple.
8) Return the stroke cover to the original position.
9-22
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 10
HXYX
1 Installation ............................................................................10-1
1-1 Installation method 1
(Arm type, moving arm type, pole type, gantry type X-axis) .......... 10-1
1-1-1 Installation bolt types .....................................................................10-1
1-1-2 Installation bolt nominal length ......................................................10-1
1-1-3 Tightening torque...........................................................................10-2
1-1-4 Installation methods ......................................................................10-2
1-2 Installation method 2 (XZ type) ...................................................... 10-4
1-2-1 Installation bolt ..............................................................................10-4
1-2-2 Installation bolt nominal length ......................................................10-4
1-2-3 Tightening torque...........................................................................10-5
1-2-4 Installation methods ......................................................................10-5
1-3 Installation method 3 (Gantry type support axis) ........................... 10-6
2 Protective Connections.........................................................10-7
2-1 Ground terminal ............................................................................. 10-7
2-2 Ground wire ................................................................................... 10-8
2-3 Wiring methods .............................................................................. 10-8
3 Installing the Tool ................................................................10-10
3-1 Arm type, gantry type 2-axis model ..............................................10-11
3-2 Moving arm type 2-axis model ..................................................... 10-12
3-3 Pole type 2-axis model................................................................. 10-13
3-4 ZH
(Arm type, gantry type, moving arm type 3rd-axis option/XZ type 2-axis model) .. 10-14
3-5 ZL
(Arm type, gantry type, moving arm type 3rd-axis option/XZ type 2-axis model) .. 10-15
3-6 ZPH (Pole type 3rd-axis option)................................................... 10-16
3-7 RH
(Arm type, moving arm type, gantry type 4th-axis option/XZ type 3rd-axis option) ..10-17
4 User Wiring and User Piping ..............................................10-18
4-1 Cable carrier type......................................................................... 10-18
4-1-1 Example of wiring and piping methods using cable carrier .........10-18
4-1-2 Cable carrier specifications .........................................................10-20
4-1-3 User I/O cable specifications .......................................................10-21
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2 Whipover cable type .................................................................... 10-22
4-2-1 Examples of wiring and piping with Whipover cable ...................10-22
5 Periodic Inspections ...........................................................10-24
5-1 Replenishing grease to the linear guide....................................... 10-24
5-2 Replenishing grease to the ball screw ......................................... 10-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
Install the HXYX by tapping holes into the installation base and securing the
robot to the base with M8 bolts from the inside of the robot. The installation
method is the same for the arm type, pole type, moving arm type and gantry type
X-axis. Note that the installation method differs for the XZ type and gantry type
support axis.
1-1
Installation method 1
(Arm type, moving arm type, pole type, gantry type X-axis)
Install the arm type, moving arm type, pole type and gantry type X-axis in the
following manner.
1-1-1
1-1-2
Installation bolt types
• Use the following type of installation bolt.
Hexagon socket head cap screw M8 Strength 8.8T
Installation bolt nominal length
WARNING
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide’s bearings and be dam-
aged.
If the installation base is made of steel, secure 1D or more (8mm or more for M8)
for the screw fitting length. When made of aluminum, secure 1.5D or more (12mm
or more for M8).
The frame thickness is 33mm. (Refer to Fig. 10-1.)
Recommended nominal length 45mm or more
Fig. 10-1
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
1-1-3
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
.
.
.
.
Recommended torque
22.5N m to 36.3N m (230kgf cm to 370kgf cm)
1-1-4
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
1) Tap M8 coares screw thread holes into the installation base where the robot is
to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Loosen the small screws (M5, 4 screws) fixing the X-axis wiring box. The
wiring box can be slid along the T slot when these screws are loosened.
Fig. 10-2
3) Remove the countersunk head screws fixing the X-axis stroke cover. (M4
countersunk head screw, 6 screws)
Fig. 10-3
!
CAUTION
The screws indicated with an asterisk (*) in the above drawing should be re-
moved from the wiring clearance after sliding the X-axis wiring box. Take care
not to damage the wires at this time. (Refer to Fig 10-4.)
10-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
Fig. 10-4
!
CAUTION
Decorative plates are attached to both ends of the stroke cover. Take care not
to lose these plates.
4) Remove the stroke cover.
If the cover is difficult to remove, manually move theY-axis to the motor side
stroke end. The cover will be easier to remove.
5) Fix the robot onto the installation base with the designated bolts.
10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
6) After installing, return the stroke cover and X-axis wiring box to the original
positions.
!
CAUTION
Always install the X-axis wiring box at the original position. The amount of pro-
jection from the cable carrier's stroke end could change, or the cable carrier
and Y-axis bracket could contact.
21
Fig. 10-5 MXY box position
1-2
Installation method 2 (XZ type)
Install the XZ type in the following manner.
1-2-1
Installation bolt
• Use the following type of installation bolt.
Hexagon socket bolt M8 Strength 8.8T
1-2-2
Installation bolt nominal length
WARNING
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide’s bearings and be dam-
aged.
If the installation base is made of steel, secure 1D or more (8mm or more for M8)
for the screw fitting length. When made of aluminum, secure 1.5D or more (12mm
or more for M8).
The frame thickness is 26.5mm. (Refer to Fig. 10-6.)
Recommended nominal length
When installation base is made of steel
35mm or more
When installation base is made of aluminum 40mm or more
10-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
Fig. 10-6
1-2-3
1-2-4
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
.
.
.
.
Recommended torque
22.5N m to 36.3N m (230kgf cm to 370kgf cm)
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
1) Tap M8 holes into the installation base where the robot is to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Remove the screws fixing the X-axis stroke cover. (M4 countersunk head
screw, 6 screws)
3) Remove the stroke cover.
If the cover is difficult to remove, manually move theY-axis to the motor side
stroke end. The cover will be easier to remove.
4) Fix the robot onto the installation base with the designated bolts.
5)
!
CAUTION
Take care not to catch the X-axis wiring when installing the stroke cover.
After installing, return the stroke cover and X-axis wiring box to the original
positions.
10-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
1-3
Installation method 3 (Gantry type support axis)
Install the gantry type support axis in the following manner.
!
CAUTION
Move the X-axis as much as possible, and tighten the bolts where the move-
ment is the lightest.
Set the X-axis and guide rail parallelism during installation. Make sure that
there is no difference in the height direction of the X-axis and guide rail installa-
tion surface.
1) Fix the robot onto the specified position of the installation base with bolts.
Do not tighten the guide rail bolt at this time. Securely fix the X-axis section
onto the installation base.
2) When the ZR-axis is provided, or if tools are already attached, move as
close to the X-axis side as possible so that a load is not applied on the
guide rail.
3) Loosen the bolt for theY-axis and support installation bracket. (Refer to
following drawing.)
4) Temporarily fix the guide rail onto the installation base with bolts.
The parallelism of the guide rail and X-axis must be set using a dial gauge or
pick gauge, etc.
5) To easily set the parallelism, first tighten the bolt loosened in step 3).
Set the X-axis near one end, and tighten the bolt on the guide rail end in this
state. Next, move the X-axis to the opposite end, and tighten the bolt on the
opposite side of the guide rail in this state. Repeat this until all bolts have
been tightened.
Y-axis
Support installation bracket
Guide rail stay
Bolts
Adjustment of gantry type support rail
10-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
2
Protective Connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground tap with
the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground terminal is located on the inside of the X-axis wiring box. (Refer to
Fig. 10-7 and Fig. 10-8.)
X-axis wiring box
Ground terminal
Fig. 10-7
10-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
Ground terminal
X-axis wiring box
Fig. 10-8 XZ type
2-2
2-3
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
Wiring methods
!
CAUTION
Accurately insert the lock washer between the ring-tongue terminal and robot.
Proper continuity may not be secured if the lock washer is dislocated.
1) Loosen the four M4 small screws, and open the X-axis wiring box cover.
2) Open holes (or notches) in the grommets on the end face of the X-axis wiring
box, and pass the ground wire through.
10-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3) Connect the ring-tongue terminal of the ground wire to the ground terminal
on the robot.
An M4 small screw with spring washer and lock washer are attached to the
ground terminal.Arrange the parts in the order of the lock washer, ring-tongue
terminal and M4 small screw with spring washer, and then tighten. (Refer to
Fig. 10-9.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 10-9
4) Return the X-axis wiring box cover to the original position.
10-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3
Installing the Tool
Install the user tool onto the robot’s tool installation surface in the following man-
ner.
WARNING
Always turn the controller power OFF before Installing a tool to prevent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
10-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-1
Arm type, gantry type 2-axis model
Eight M8 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider installation surface. (Refer to Fig. 10-10.) Install the user tool onto
the Y-axis slider using these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these to
fix light loads other than the tool, such as a wiring retainer.
4-M5×0.8 Depth12
50
52.5
(The same position on the
opposite surface at two locations)
2-φ6H7 Depth10
155
142
120
8-M8×1.25
Depth25
12.5
25 (Effective screw depth)
Fig. 10-10 HXYX arm type, gantry type
!
CAUTION
If the fitting length is less than 16mm, the threads could be damaged during
tightening. Note that if the fitting length exceeds 25mm, the bolt end could con-
tact the cover.
Select the nominal length of the tool fixing bolt so that the fitting length of the
screw fixing the tool is 16mm or more, 25mm or less.(Refer to the cross-section
drawings in Fig. 10-10.)
10-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-2
Moving arm type 2-axis model
The moving arm type has an aluminum-cast bracket on the end of the Y-axis.
Install the tool on this bracket.
Twelve M8 coarse thread tap holes and two φ6 reamer holes are opened on the
bracket.
133
12.5
20
4-M8×1.25
63
2-φ6H7 Depth8
78
Fig. 10-11 HXYX moving arm type
!
CAUTION
If the fitting length is less than 16mm, the threads could be damaged during
tightening. If the fitting length is longer than 30mm, the screw could contact the
Y-axis.
Select the minimum fixing bolt screw length so that the screw fitting length is
16mm or more.
10-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-3
Pole type 2-axis model
Four M8 coarse thread tap holes and two $8 reamer holes are opened on the tool
installation surface of theY-axis slider. (Refer to Fig. 10-12.) Install the user tool
onto the Y-axis slider using these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these to
fix light loads other than the tool, such as a wiring retainer.
185
(Tolerance between knock (0.02)
12.5
4-M5×0.8 Depth15
2-φ8H7 Depth10
4-M8×1.25 Depth30
(The same position on the
opposite surface at two locations)
1.5
15
Fig. 10-12 HXYX pole type
!
CAUTION
If the screw's fitting length is less than 16mm, the screw threads could be dam-
aged during tightening. If the screw length from the installation surface is longer
than 30mm, the screw end could contact the frame.
Select the under head length of the bolt fixing the tool so that the screw length
from the slider installation surface is 16mm or more, 30mm or less.
10-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-4
ZH
(Arm type, gantry type, moving arm type 3rd-axis option/
XZ type 2-axis model)
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the screw length exceeds 27mm from the installation surface, the
screw could contact the bottom.
When using the 3rd-axis model with ZH for the 3rd-axis, install the workpiece
onto the ZH frame in the following manner.
M6 coarse thread tap holes are opened on the frame's workpiece installation sur-
face. Install the tool using these holes. The tap depth is 10mm.
Select the under head length of the installation bolt so that the screw length from
the installation surface is 9mm or more, 27mm or less.
Refer to the XY-X Series catalog
for the installation position.
100
22
22
78
Fig. 10-13 Tool installation ZH
NOTE
There is a step on the ZH frame.
The actual tool installation surface is the shaded section shown above.
10-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-5
ZL
(Arm type, gantry type, moving arm type 3rd-axis option/
XZ type 2-axis model)
When using the 3rd-axis model with ZL for the 3rd-axis, install the workpiece
onto the ZL slider in the following manner.
Eight M6 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider. (Refer to Fig. 10-14.) Install the user tool onto the ZL slider using
these holes.
Four M5 coarse thread tap holes are opened on the side of the slider. Use these to
fix loads other than the tool, such as the wire retainer.
23.5
19
2-φ6H7 Depth8
8-M6×1.0 Depth8
110
(Tolerance between knock (0.02)
4-M5×0.8 Depth7
135
20
90
20
Fig. 10-14 ZL
!
CAUTION
If the fitting length is less than 6mm, the threads could be damaged during
tightening. If the fitting length is longer than 8mm, the end of the screw could
contact the cover stroke.
NOTE
There is a step on the top of the slider. The actual tool installation surface is the
shaded section shown above.
Select the nominal length of the bolt for fixing the tool so that the screw fitting
length is 6mm or more, 8mm or less. (Refer to the cross-section drawing in Fig.
10-14.)
10-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-6
ZPH (Pole type 3rd-axis option)
When ZPH is attached for the 3rd-axis of the pole type, install the tool onto the
aluminum bracket at the end of the ZP-axis.
Twelve M6 coarse thread tap holes and two φ6 reamer holes are opened on the
bracket.
100
70
44
2-φ6H7 Depth6
12-M6×1.0
32
20
10
Fig. 10-15 ZPH
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the bolt screw length exceeds 30mm from the installation surface,
the screw could contact the Y-axis.
Select the minimum nominal length of the fixing bolt so that the length is 9mm or
more from the tool installation surface.
10-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3-7
RH
(Arm type, moving arm type, gantry type 4th-axis option/
XZ type 3rd-axis option)
!
CAUTION
When fixing with the tap holes, always fix at several holes. If fixed with only one
hole, the loosening torque could act during operation can cause loosening.
If the rotary axis RH is attached to the 4th-axis, install the tool onto the shaft at
the end of RH.
Five M8 coarse thread tap holes are opened on the end of the shaft. Install the tool
using these holes. The tool can also be installed with a bolt coupling or split
clamp using the outer diameter of the shaft.
φ35h7
φ38
φ75h8
0
φ98-0.2
5-M8×1.25
Depth20
(PCD. 20)
Fig. 10-16 RH
NOTE
The φ75 section shown below is the non-movable section. The rotary shaft is the
section below φ38.
10-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
4-1
Cable carrier type
A cable carrier is mounted as a standard between the X and Y axes. When 3rd-
axis are used, a cable carrier is also provided between theY and Z axes, and when
using 4th-axis, a cable carrier is also provided between the Z and R axes. Lay the
wiring and piping to the tool using these ducts. A 0.3sq 10-core flexible cable is
wired from the X-axis wiring box to the final axis' wiring box, and can be used
freely. The wiring and piping methods for a 2-axis arm type are explained below
as an example.
4-1-1
Example of wiring and piping methods using cable carrier
1) Remove the four M4 small screws and open the X-axis wiring box cover.
2) Rubber grommets are attached to the end face of X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through.
10-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3) Remove the harness retainer located at the cable carrier outlet. (Hexagon
socket bolt M5, 2 bolts)
Harness retainer
4) Pass the required wires and pipes through the cable carrier.
The cable carrier has an outer lid that can be opened and closed easily. Use a
flat-tip screwdriver to open the lid. Press this lid in to close it.
5) Open the Y-axis wiring box cover, and lay the required wiring and piping.
6)
!
CAUTION
1. The wires could be damaged if the harness retainer is tightened too much.
2. Manually move the robot by the full stroke before fixing to confirm that the
harness and air tube, etc., are not pulled in the cable carrier. These could be
damaged if pulled during operation.
When completed with the wiring, fix with the harness retainer in the wiring box.
7)
!
CAUTION
Take care not to catch the harness or air tube with the cover.
Return each wiring box cover to the original position.
10-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
4-1-2
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sectional
area. (This ratio is called the cable carrier space factor.)
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially by YAMAHA are shown below.
2-axis specifications X-Y cable carrier
2-axis I/O specifications Y-axis cable carrier
User I/O wire φ10.1
Power wire φ7.6
Signal wire φ8.2
User I/O wire φ10.1
77
93
57
73
3-axis specifications X-Y cable carrier
XZ type 2-axis specifications X-Z cable carrier
3-axis specifications Y-Z cable carrier
User I/O wire φ10.1
Power wire φ9.8
User I/O wire φ10.1
Power wire φ7.6
Signal wire φ10.1
Signal wire φ8.2
77
93
57
73
XZ type 3-axis specifications X-Z cable carrier
4-axis specifications Y-Z cable carrier
4-axis specifications X-Y cable carrier
Signal wire φ11
User I/O wire φ9.2
Power wire φ9.0
Power wire φ7.6
Power wire φ9.8
Signal wire φ10.1
Signal wire φ9.2
User I/O wire φ10.1
77
93
57
73
XZ type 3-axis specifications
(ZRH)
4-axis specifications Z-R cable carrier
Signal wire φ8.2
Power wire φ7.6
Signal wire φ10.1
Signal wire φ10.1
Power wire φ7.6
Signal wire φ10.1
Power wire φ7.6
Power wire φ7.6
(ZH)
(ZRL)
57
73
57
73
57
73
Fig. 10-17
10-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
4-1-3
User I/O cable specifications
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
With the cable carrier specifications, signal wires (0.3mm2 × 10 wires) that can
be used freely by the user are laid as a standard between the X-axis wiring box
and final axis' wiring box.
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed. Attach these to the user wiring to eliminate wiring led through
the robot.
Crimp the enclosed pins onto the user wiring, and insert into the connector.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
Refer to "1-2. User I/O wiring" in Chapter 5 "Specifications" for details on the
wiring specifications.
10-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
4-2
Whipover cable type
!
CAUTION
Do not clamp the wires or tubes to the outside of the independent cable. The
independent cable could sag or break and ultimately be disconnected.
The signal wires (0.3mm2 × 7 wires) and air tubes (4 × 2.5, 2 tubes) are incorpo-
rated in the Whipover cable. Use these to wire and pipe to the tool.
Signal Connector NO
NO Connector Remarks
Part No.
Part name
SM connector
SM connector
Contact
Part No.
SMR-10V-B
Qty.
1
Brown
Red
General-
purpose
I/O
I/O
q
1
2
3
1
2
I/O
w
1
2
3
4
5
Orange
Blue
3
4
SMP-10V-BC
1
4
5
6
7
SYM-001T-0.6
SHF-001T-0.8BS
7
Purple
Gray
5
6
Contact
7
White
Cable
1
7
8
8
9
9
10
10
P
P
BK
I/O
BK
I/O
t
qe
wr
ORG
ORG
M
M
Air tube
Air tube
Controller side
Tool side
Fig. 10-18 Whipover cable user-wire specifications
4-2-1
Examples of wiring and piping with Whipover cable
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
1) Crimp the user's cable and tool wiring onto the enclosed connector.
Refer to section “1-2. User I/O wire” in Chapter 5 “Specifications” for de-
tails on the enclosed connector and pin specifications.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
2) When using an air tube, prepare an air coupler for connecting the user air
tube with the YAMAHA air tube.
10-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
3) Open the X-axis wiring box cover.
Fig. 10-19
4) Rubber grommets are attached to the X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through. Crimp the enclosed connectors onto the cables.
5) Connect the connectors, and connect the air tubes using the air couplers.
6) Open the Y-axis wiring box cover.
7) Rubber grommets are also attached to the Y-axis wiring box.
Open holes in these grommets, and pass the tool side cables and air tubes
through.
8) Connect the connectors in the same manner as the X-axis, and connect the air
tubes with the air couplers.
9)
!
CAUTION
Take care not to catch the wiring or air couplers when installing the covers.
When completed with all wiring work, return each wiring box cover to the
original positions. Sandwich the X-axis wiring and air tube with the protec-
tive material at the wire lead-out port of each wiring box.
10-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
5
Periodic Inspections
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts, turn OFF the controller, wait for a while and check that
the part has cooled.
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
5-1
Replenishing grease to the linear guide
Grease must be replenished to this linear guide periodically. Select the grease
from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
2) Place a sign indicating “Work In Progress” so that other operators do not turn
the controller power ON.
3) Remove the axis stroke cover when replenishing grease.
Refer to section "1. Installation" for details on opening the X-axis stroke
cover.
10-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
4) Replenish the grease with one of the following methods.
Method 1: Using a grease gun, replenish grease from the grease nipple in-
stalled on the linear guide bearings.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the linear guide bearings and rail.
The X-axis andY-axis each have four linear guide bearings. Replenish grease
to all four bearings.
Wipe off any excessive grease that has seeped out to the rail.
Recommended grease gun: MG70 (THK X-axis, Y-axis H-type nozzle)
(THK Z-axis (ZL) N-type nozzle)
Method 2: After wiping off the grease adhered on the rail and on the bear-
ing seal section with a rag, etc., apply a light coat of grease di-
rectly onto the guide rail with a finger.
NOTE
Due to the structure of ZH, grease can be replenished only with this
method.
When replenishing grease to ZH, turn the power OFF when near the
center of the stroke, and then apply grease to the top and bottom of the
guide.
5) Return the stroke cover to the original position.
5-2
Replenishing grease to the ball screw
Prepare the following recommended grease nipple beforehand.
Recommended grease nipple : A-M6X1 type (JIS B1575)
Recommended grease
: Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
10-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 HXYX
Replenishment methods
Refer to the following procedures and replenish the grease.
1) Remove the stroke cover of the axis to which grease is to be replenished.
2) Replenish the grease with one of the following methods.
!
CAUTION
Always remove the grease nipple after replenishing the grease. Failure to do
so could cause damage if the grease nipple and robot interfere.
Method 1: Install the grease nipple onto the M6 tap hole on the ball screw
flange surface, and replenish grease using the grease gun.
Sufficient grease has been replenished when new grease starts to seep out to
the screw shaft.
Wipe off any excessive grease.
Recommended grease gun : MG70 (THK H-type nozzle)
Method 2: After wiping off the grease adhered on the rail and on the bearing
seal section with a rag, etc., apply a light coat of grease directly
onto the guide rail with a finger.
NOTE
Due to the structure of ZH, grease can be replenished only with this
method.
3) Return the stroke cover to the original position.
10-26
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 11
FXYBX/SXYBX
1 Installation ............................................................................11-1
1-1 Installation bolt types ......................................................................11-1
1-2 Installation bolt nominal length........................................................11-1
1-3 Tightening torque ............................................................................11-2
1-4 Installation methods ........................................................................11-2
2 Protective connections ......................................................... 11-3
2-1 Ground terminal ..............................................................................11-3
2-2 Ground wire ....................................................................................11-4
2-3 Wiring methods (Cable carrier type) ...............................................11-4
2-4 Wiring methods (Whipover cable type) ...........................................11-6
3 Installing the Tool ..................................................................11-7
3-1 FXYBX arm type 2-axis model........................................................11-7
3-2 SXYBX arm type 2-axis model........................................................11-8
3-3 SXYBX-ZF (XZ type 2-axis, arm type 3rd-axis option) ...................11-9
3-4 ZS/ZRS (FXYBX, SXYBX 3/4-axis option)....................................11-10
3-5 ZFH (Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option ........................................................................ 11-11
3-6 ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-axis model) ... 11-12
4 User Wiring and User Piping .............................................. 11-13
4-1 Cable carrier type..........................................................................11-13
4-1-1 Example of wiring and piping methods using cable carrier ......... 11-13
4-1-2 Cable carrier specifications ......................................................... 11-15
4-1-3 User I/O cable specifications ....................................................... 11-16
4-2 Whipover cable type .....................................................................11-16
4-2-1 Examples of wiring and piping with Whipover cable ................... 11-17
5 Changing the Motor Installation Position ............................ 11-19
5-1 Changing the motor installation position .......................................11-19
6 Installing the Cover ............................................................. 11-21
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Adjusting the Timing Belt Tension....................................... 11-22
7-1 Adjusting the drive belt tension .....................................................11-23
7-2 Adjusting the speed reduction belt tension ...................................11-25
8 Periodic inspections............................................................ 11-27
8-1 Replacing the motor......................................................................11-27
8-2 Replacing the drive belt ................................................................11-28
8-3 Replacing the speed reduction belt...............................................11-31
8-4 Replacing the slider ......................................................................11-32
8-5 Replenishing the grease ...............................................................11-33
8-5-1 Replenishing grease to the linear guide ...................................... 11-33
8-5-2 Replenishing grease to the ball screw (ZF) ................................. 11-35
8-6 Periodic inspection of the ZS/ZRS unit .........................................11-36
8-6-1 Replenishing grease to the Z-axis ball screw and ball spline ...... 11-36
8-6-2 Adjusting the R-axis belt tension (ZRS) ...................................... 11-37
8-6-3 Replacing the R-axis harmonic drive (ZRS) ................................ 11-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
Install the FXYBX by opening through holes on the installation base and secur-
ing with M5 bolts from below. (M5 tap holes are opened on the bottom of the
robot.)
Install the SXYBX by opening through holes on the installation base and secur-
ing with M6 bolts from below. (M6 tap holes are opened on the bottom of the
robot.)
1-1
1-2
Installation bolt types
• Use the following type of installation bolt.
FXYBX
SXYBX
Hexagon socket head cap screw M5 Strength 8.8T
Hexagon socket head cap screw M6 Strength 8.8T
Installation bolt nominal length
FXYBX
Select the under head length so that the screw length from the bottom of the robot
is 8mm or more, 10mm or less.
Fig. 11-1
!
CAUTION
Note that the screw will contact the bottom if the screw length from the robot
bottom is longer than 10mm.
11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
SXYBX
Select the under head length so that the screw length from the bottom of the robot
is 9mm or more, 27mm or less.
Fig. 11-2
!
CAUTION
Note that the screw will contact the bottom if the screw length from the robot
bottom is longer than 27mm.
1-3
1-4
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
.
FXYBX
SXYBX
Recommended torque
Recommended torque
60 to 90kgf cm
.
100 to 130kgf cm
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
1) Open a through hole on the installation base’s robot installation surface. Re-
fer to the XY-X Series catalog for the hole positions.
2) Set the robot on the installation base and fix with the designated bolts from
below.
11-3
11-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
2
Protective connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground tap with
the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground terminal for the cable carrier type is provided in the X-axis wiring
box. (Refer to Fig. 11-4.)
Ground terminal
Fig. 11-4 Cable carrier model
11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
The ground terminal for the Whipover cable type is provided on the end face of
the X-axis wiring box. (Refer to Fig. 11-5.)
Ground terminal
Fig. 11-5 Whipover cable type
2-2
2-3
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
Wiring methods (Cable carrier type)
!
CAUTION
Accurately insert the lock washer between the ring-tongue terminal and robot.
Proper continuity may not be secured if the lock washer is dislocated.
!
CAUTION
Take care not to catch the harness and ground wire from the X-axis with the
cover of X-axis wiring box when installing the cover.
11-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
1) Remove the four M4 screws from the top of the X-axis wiring box, and loosen
the M4 screw on the end face.
Remove
X-axis wiring box
Loosen
Fig. 11-6
2) Open the X-axis wiring box cover.
Lift up the back of the wiring box, push it forward and then pull it upward
and off.
Fig. 11-7 Opening the wiring box
3) Connect the ground wire to the ground terminal attached to the top of the
X-axis wiring box.
An M4 small screw with spring washer and lock washer are attached to the
ground terminal.Arrange the parts in the order of the lock washer, ring-tongue
terminal and M4 small screw with spring washer, and then tighten. (Refer to
Fig. 11-8.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 11-8
11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4) Return the wiring box cover to the original position following steps 1 and 2
in reverse.
Lead out the ground wire from the user wiring outlet on the end face of the
X-axis wiring box.
2-4
Wiring methods (Whipover cable type)
For the independent cable type, wire the ground wire to the ground terminal on
the end face of the X-axis wiring box. Refer to 3). in 2-3. Wiring methods (Cable
carrier type) for details.
11-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
3
Installing the Tool
Install the user tool onto the robot's tool installation surface in the following manner.
WARNING
Always turn the controller power OFF before Installing a tool to prerent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
3-1
FXYBX arm type 2-axis model
Four M5 coarse thread tap holes and two φ5 reamer holes are opened on the Y-
axis slider. (Refer to Fig. 11-9.) Install the user tool onto the Y-axis slider using
these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these as
required.
15
40
4-M5ζ0.8 Depth9.5
2-φ5H7 Depth4
70
52
4-M5×0.8 Depth6
6
2.8
Fig. 11-9 FXYBX arm type
11-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
Select the under head length of the bolt for fixing the tool so that the screw length
from the slider installation surface is 6mm or less.
!
CAUTION
If the screw length from the installation surface is 8mm or more, the screw
could interfere with the stroke cover.
NOTE
There is a step on the top of the slider. The actual tool installation surface is the
shaded section shown above.
3-2
SXYBX arm type 2-axis model
Eight M6 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider.(Refer to Fig. 11-10.) Install the user tool onto the Y-axis slider
using these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these as
required.
4-M5×0.8 penetration
(same on opposite surface)
20
50
90
70
32
2-φ6H7 Depth10
8-M6×1.0 Depth16
Fig. 11-10 SXYBX arm type
11-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
Select the under head length of the bolt for fixing the tool so that the screw length
from the slider installation surface is 6mm or less.
!
CAUTION
Note that if the screw length from the installation surface is 16mm or more, the
screw will contact the bottom.
3-3
SXYBX-ZF (XZ type 2-axis, arm type 3rd-axis option)
When using the XZ type 2-axis model or if ZF is attached for the arm type 3rd-
axis model, install the workpiece onto the ZF slider in the following manner.
Four M5 coarse thread tap holes and a φ5 reamer hole are opened on the slider’s
workpiece installation surface. Use these to install the tool.
Four M5 coarse thread tap holes are also opened on the slider side. Use these as
required.
110
100
(Tolerance between knock (0.02)
10
9
9
4-M5×0.8 Depth9
4-M5×0.8 Depth12
2-φ5H7 Depth15
Stroke cover
Fig. 11-11 ZF
Select the maximum length so that the screw length of the tool fixing bolt is
12mm or less.
The screw fitting length should be 8mm or more.
!
CAUTION
Note that if the screw length from the installation surface is 12mm or more, the
screw will contact the bottom.
11-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
3-4
ZS/ZRS (FXYBX, SXYBX 3/4-axis option)
WARNING
Use the tap hole on the end of the shaft only to prevent the tool from
dislocating.
Do not use only this hole to install the tool. The tool could dislocate and
fly off the installation section during robot operation.
When the ZS or ZRS unit is attached to the 3rd or 4th-axis, install the tool onto
the ZS or ZRS shaft in the following manner. (The ZS and ZRS shaft have the
same shape.)
Use the φ12 section on the shaft, and fix the tool with a bolt coupling or split clamp.
φ5
Hole for rotation stop tool
0
12
-0.018
M8×1.25 Depth15
Fig. 11-12 Tool installation ZS/ZRS
Hole
diameter
Bolt
Slit
Spline shaft
End effector or stay
Tap section
Fig. 11-13
Example : For split clamp
Recommended bolt M4 or more
Quantity
Tightening torque
Hole diameter
2 or more
.
4.5N m (46kgfm)
φ12+0.018
11-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
3-5
ZFH
(Arm type, gantry type, moving arm type 3rd-axis option)
XZ 2nd-axis option
When using the 3rd-axis model with ZFH for the 3rd-axis, install the workpiece
onto the ZFH frame in the following manner.
Four M5 coarse thread tap holes and a φ5 reamer hole are opened on the frame's
workpiece installation surface. Install the tool using these holes. The tap depth is
9mm.
4-M5×0.8 Depth9
2-φ5H7 Depth8
A
A
70
(Tolerance between knock (0.02)
31
28
31
SEC A-A
Fig. 11-14 Tool installation ZFH
NOTE
There is a step on the ZFH frame.
The actual tool installation surface is the shaded section shown above.
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the screw length exceeds 27mm from the installation surface, the
screw could contact the bottom.
11-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
3-6
ZFL
(Arm type, moving arm type, 3rd-axis option/XZ type 2-
axis model)
When using the 3rd-axis model with ZFL for the 3rd-axis, install the workpiece
onto the ZFL slider in the following manner.
Six M5 coarse thread tap holes and a φ5 reamer hole are opened on the slider's
workpiece installation surface. Install the tool using these holes. Six M5 coarse
thread tap holes are opened on the slider side. Use these as required to fix light
loads other than the tool, such as the wiring retainer.
110
10
6-M5×0.8 Depth9
100
(Tolerance between knock (0.02)
2-φ5H7 Depth15
6-M5×0.8 Depth12
9
9
Stroke cover
Fig. 11-15 ZFL
Select the maximum nominal length of the tool fixing bolt so that the screw fit-
ting length is 12mm or less.
YAMAHA recommends a screw fitting length of 8mm or more.
!
CAUTION
If the bolt fitting length is 12mm or more from the installation surface, the bolt
will contact the bottom.
11-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
4-1
Cable carrier type
A cable carrier is mounted as a standard between the X and Y axes. When using
3-axes, a cable carrier is also provided between theY and Z axes. Lay the wiring
and piping to the tool using these ducts. A 0.3sq 10-core flexible cable is wired
from the X-axis wiring box to the final axis' wiring box, and can be used freely.
(Refer to the "User wiring specifications" at the end of this section for details.)
The wiring and piping methods for a 2-axis arm type are explained below as an
example.
4-1-1
Example of wiring and piping methods using cable carrier
1) Open the X-axis wiring box cover. (Refer to 2-3. Wiring methods in Chapter
2. Protective Connections.)
2) Remove the harness retainer located at the cable carrier outlet. (Hexagon
socket bolt M5, 2 bolts)
Harness retainer
3) Pass the cables and air tubes through the cable carrier. The cable carrier has
an outer lid that can be opened and closed easily. Use a flat-tip screwdriver to
open the lid. Press this lid in to close it. Open and close this lid as necessary.
11-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4) Open the Y-axis wiring box cover.
5) Lay out the wiring in the Y-axis box as necessary.
6)
!
CAUTION
1. The wires could be damaged if the harness retainer is tightened too much.
2. Manually move the robot by the full stroke before fixing to confirm that the
harness and air tube, etc., are not pulled in the cable carrier. These could be
damaged if pulled during operation.
After leading all wires, fix the wires with the harness retainer.
7)
!
CAUTION
Take care not to catch the harness or air tube with the cover.
Assemble the wiring box cover at the original position.
State of X-axis wiring box when wiring is completed
State with cover installed
11-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4-1-2
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sec-
tional area. (This ratio is called the cable carrier space factor.)
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially by YAMAHA are shown below.
X-Y cable carrier
2-axis specifications
Y-Z cable carrier
2-axis I/O specifications
User I/O wire φ10.1
User I/O wire φ10.1
Power wire φ9.6
Signal wire φ8.2
85
57
73
100
3-axis specifications
User I/O wire φ10.1
User I/O wire φ10.1
Power wire φ9.8
Power wire φ7.6
Signal wire φ8.2
Signal wire φ10.1
85
57
73
100
4-axis specifications
User I/O wire φ10.1
Power wire φ9.8
Signal wire φ11
Power wire φ9.8
User I/O wire φ10.1
Power wire φ7.6
Signal wire φ10.1
Signal wire φ11
85
57
73
100
Fig. 11-16
11-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4-1-3
User I/O cable specifications
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
With the cable carrier model, signal wires (0.3mm2 × 10 wires) that can be used
freely by the user are laid as a standard between the X-axis wiring box and final
axis' wiring box (the Z-axis wiring box when using 3-axis specifications).
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed. Attach these to the user wiring to eliminate wiring led through
the robot.
Crimp the enclosed pins onto the user wiring, and insert into the connector.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
Refer to "1-2. User I/O wiring" in Chapter 5 "Specifications" for details on the
wiring specifications.
4-2
Whipover cable type
!
CAUTION
Do not clamp the wires or tubes to the outside of the independent cable. The
independent cable could sag or break and ultimately be disconnected.
The signal wires (0.3mm2 × 7 wires) and air tubes (4 × 2.5, 2 tubes) are incorpo-
rated in the Whipover cable. Use these to wire and pipe to the tool.
Signal Connector NO
NO Connector Remarks
Part No.
Part name
SM connector
SM connector
Contact
Part No.
SMR-10V-B
Qty.
1
Brown
Red
General-
purpose
I/O
I/O
q
1
2
3
1
2
I/O
w
1
2
3
4
5
Orange
Blue
3
4
SMP-10V-BC
1
4
5
6
7
SYM-001T-0.6
SHF-001T-0.8BS
7
Purple
Gray
5
6
Contact
7
White
Cable
1
7
8
8
9
9
10
10
P
P
BK
I/O
BK
I/O
t
qe
wr
ORG
ORG
M
M
Air tube
Air tube
Tool side
Controller side
Fig. 11-17 Whipover cable user-wire specifications
11-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4-2-1
Examples of wiring and piping with Whipover cable
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
1) Crimp the user's cable and tool wiring onto the enclosed connector.
Refer to section “1-2. User I/O cable” in Chapter 5 “Specifications” for de-
tails on the enclosed connector and pin specifications.
2) When using an air tube, prepare an air coupler for connecting the user air
tube with the YAMAHA air tube.
3) Remove the resin cover from the end face of the X-axis wiring box. (M4
screw, 4 screws)
4) Rubber grommets are attached to the X-axis wiring box.
Open holes (or notches) in these grommets, and pass the required cables and
air tubes, etc., through. Crimp the enclosed connectors onto the cable before-
hand.
5) Pull the I/O connector and air tube out of the X-axis wiring box. In the same
manner, pull the user cable and air tube passed in step 4) out from the wiring
box.
!
CAUTION
Carefully pull out the minimum length of wiring and air tube with which connec-
tions can be made.
If these are pulled with force, trouble such as dislocation or pin faults could
occur.
6) Connect the connectors, and connect the air tubes using the air couplers.
Return the air tube into the wiring box after connecting.
7) Open the Y-axis wiring box cover. (M4 screw, 4 screws)
8) Set the required cables and air tubes, etc., into the Y-axis wiring box.
Crimp the enclosed connectors onto the cable beforehand.
9) Connect the connector in the same manner as the X-axis, and connect the air
tube using an air coupler, etc.
If wires are led out from the Y-axis wiring box, use the rubber grommet at-
tached to the upper cover of the Y-axis wiring box.
11-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
10) When completed with all wiring work, return each wiring box cover to the
original positions. Sandwich the X-axis wiring and air tube with the protec-
tive material at the wire lead-out port of each wiring box.
!
CAUTION
Take care not to catch the wiring or air couplers when installing the covers.
When leading out the wires
from the Y-axis wiring box,
use the grommets on the upper cover
of the Y-axis wiring box
Remove the upper cover
r
t
Carry out wiring and piping
Set the harness and air tube
from the grommets on the
X-axis wiring box
w
X-axis wiring box end face resin cover
q
Remove the four M4 screws
e Carry out wiring and piping
Fig. 11-18
11-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
5
Changing the Motor Installation Position
5-1
Changing the motor installation position
WARNING
Always turn the controller power OFF before starting this work. Serious
accidents could occur if the robot starts moving during this work.
The position for installing the FXYBX and SXYBX axis on the motor can be
freely selected. Interference with the motor case can be suppressed to a minimum
and space can be used effectively. The methods for changing the motor installa-
tion position are described below.
1) Remove the screws securing the belt cover, and remove the cover.
2) Remove the four bolts installing the motor plate.
Motor plate
Motor plate bolt
3) Detach the belt from the pully. Change the motor orientation as desired, and
temporarily tighten the four motor plate installation bolts. At this point, set
the motor case toward the belt loosening side.
Motor plate
Motor plate
installation bolt
11-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4) First attach the belt to the small pulley, and then fit it onto the large pulley.
5) Temporarily fix the motor plate installation bolts while pulling on the motor
case.
Motor case
Motor plate
installation bolt
6) Refer to “Chapter 11 7-1-2. Adjusting the speed reduction belt tension” and
adjust the belt tension.
7) Install the belt cover.
!
CAUTION
Confirm that the large pulley teeth and belt teeth are correctly engaged. Positional
deviation or premature belt damage could occur if the teeth are not sufficiently
engaged.
11-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
6
Installing the Cover
If the X-axis stroke is long, a slider mechanism is provided in the X-axis stroke
cover. The alignment of the slider and upper cover must be adjusted when install-
ing the cover.
Target
FXYBX X stroke 2150mm or more
SXYBX X stroke 2450mm or more
!
CAUTION
If the slider and upper cover are not correctly adjusted, the slider could be
damaged prematurely.
When inserting into the U-character groove, take care not to cut the slider with
the edge of the cover.
1) Turn the controller power OFF.
2) Insert the slider into the U-character groove on the center of the upper cover.
Set the upper cover so that it is parallel with the axis movement direction at
this time.
Slider travel groove
Slider
3) Temporarily fasten the four upper cover installation screws, move the table
from the motor side to the counter-motor side end, and then completely tighten
the screws on the counter-motor side. Move the table to the motor side again,
and then completely tighten the two upper cover installation screws on the
motor side.
4) Move the slider by hand to check that it travels along the upper cover smoothly.
11-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
7
Adjusting the Timing Belt Tension
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts, turn the controller power OFF, wait for a while and check
that the part has cooled.
WARNING
There is a risk of injury if fingers, etc., are caught between the drive sec-
tion pulley and belt. Always turn the controller power OFF and carefully
carry out the work if these parts may be contacted.
!
CAUTION
The position will deviate when the belt tension is adjusted.
Carry out return-to-origin or absolute reset, and reset the point data.
The X-axis and theY-axis for the FXYBX and SXYBX use a timing belt to drive
the slider.
If the timing belt tension is week, adjust the belt tension with the following pro-
cedures.
L/2
L/2
Table
Push-pull scale
Deflection
Push-pull scale
Deflection
Load
Load
Pulley
Belt
Belt
Pulley
Pulley
Fig. 11-19 Adjusting the speed
reduction belt tension
Fig. 11-20 Adjusting the drive
belt tension
5
Belt
Push-pull scale
Nut
Hole
Stay
Nut
Fig. 11-21 Stay (example)
15
3.2 thick sheet metal
11-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
7-1
Adjusting the drive belt tension
!
CAUTION
On robot models having a long stroke, a slider is provided in the upper cover.
Pull off the upper cover with a parallel movement in the axis movement direc-
tion.
1) Turn the controller power OFF.
2) Remove the end cover.
3) Remove the upper cover installation screws, and remove the upper cover.
4) FXYBX X-axis, SXYBX X, Y axes
Attach the enclosed belt tension adjustment bolt, and loosen the eight belt
stay installation bolts. Turn the enclosed adjustment bolt to apply tension on
the belt.
Adjustment bolt
Belt stay installation bolt
Belt stay
FXYBX Y-axis
Loosen the belt holder fixing bolt (on slot side), and turn the adjustment bolt
to apply tension on the belt.
11-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
5) Move the slider by hand so that the distance between the slider end face and
base block end face is 150mm. Apply a load at the L = 115mm position from
the base block end for the FXYBX X-axis, at L = 65mm for the FXYBX
Y-axis, and L = 129mm for the SXYBX X and Y axes.
150mm150mm
L
6) Temporarily tighten the belt stay installation bolt. If the deflection is within
the range shown in Table 11-1 when the belt is pressed with the designated
load, the tension is appropriate. If the deflection is not within the range of
Table 11-1, repeat steps 4) and 5) to adjust the tension.
Table 11-1 Drive belt load and deflection
Model
Load (N)
Load (kgf)
0.5 to 0.6
0.6 to 0.7
0.6 to 0.7
Deflection(mm)
FXYBX X-axis
4.9 to 5.9
5.9 to 6.9
5.9 to 6.9
2
2
2
FXYBX Y-axis
SXYBX X-axis, Y-axis
7) Tighten the belt stay installation bolt, and remove the belt tension adjustment
bolt.
8) Refer to “Chapter 11 6. Installing the Cover”, and install the upper cover.
Finally, install the end cover.
Reference
(Adjusting the drive belt tension with a tension meter)
Use of a belt tension gauge is recommended to obtain more accurate measure-
ments.
Recommended tension meter U-505 (UNITTA)
Measurement method
In step 5) of the adjustment of the drive belt tension, pull the belt at the position
where the load is applied, and adjust to the following values.
Refer to the instruction manual enclosed with each measuring instrument for
details on using the belt tension gauge.
Tension
(N)
Frequency
(Hz)
Span length Belt width
Unit weight
(g/mm width×m length)
Model
(mm)
(mm)
20
FXYBX X-axis
FXYBX Y-axis
127 to 147
127 to 147
86 to 93
230
4.0
4.0
4.0
20
117 to 126
79 to 84
170
25
SXYBX X-axis, Y-axis 169 to 188
258
11-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
7-2
Adjusting the speed reduction belt tension
1) Turn the controller power OFF.
2) Remove the end cover.
3) Apply the load listed in Table 11-2 at the center of both pulleys, and measure
the deflection at that point. If the results are within the range given in Table
11-2, the tension is suitable.
Table 11-2 Speed reduction belt load and deflection
Model
Load (N)
Load (kgf)
0.6 to 0.7
0.4 to 0.47
0.6 to 0.7
Deflection (mm)
FXYBX X-axis
5.9 to 6.9
3.9 to 4.6
5.9 to 6.9
3
3
3
FXYBX Y-axis
SXYBX X-axis, Y-axis
4) If adjustments are required, loosen the motor plate installation bolt.
5) If the value measured in step 3) is less than Table 11-2, move the motor case
in the direction to increase the tension. If larger than the values given in Table
11-2, move the motor case in the direction to decrease the tension.
Tension increases
Tension decreases
Motor plate
installation bolt
11-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
6) Measure the belt tension again with the procedure given in step 3). The belt
adjustment is completed if the measured value is within the range given in
Table 11-2. If the measured value is not within the range of Table 11-2, re-
peat steps 3) to 5).
7) Tighten the motor plate installation bolt.
8) Install the belt cover.
Reference
(Adjusting the speed reduction belt tension with a tension measuring instrument)
Use of a belt tension gauge is recommended to obtain more accurate measure-
ments.
Recommended tension gauge U-505 (UNITTA)
Measurement method
In step 3) of the adjustment of the speed reduction belt tension, pull the belt at the
position where the load is applied, and adjust to the following values.
Unit weight
(g/mm width × m length)
Span length Belt width
Tension
(N)
Frequency
(Hz)
Model
(mm)
(mm)
20
FXYBX X-axis
FXYBX Y-axis
44 to 49
29 to 34
180 to 190
180 to 190
180 to 190
82
2.5
2.5
2.5
12
88.5
82
20
SXYBX X-axis, Y-axis 44 to 49
11-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8
Periodic inspections
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
8-1
Replacing the motor
!
CAUTION
The position will deviate when the motor is replaced. After replacing the motor,
return-to-origin must be carried out and the point data must be reset. Remem-
ber the relation of the installation positions when removing any parts.
1) Turn the controller power OFF.
2) Remove the belt cover.
3) Remove the motor case and motor cover.
Motor cover
Motor case
4) Remove the four motor installation bolts, and remove the motor.
11-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
5) Loosen the two pulley set screws, and remove the pulley.
6) Replace the motor, and attach the pulley to the motor. Insert so that the two
set screws perpendicularly contact the D face of the motor shaft.
NOTE
The parts can be correctly assembled by projecting the set screws by approx. 0.1
to 0.2mm from the inner diameter.
7) Install the motor onto the main body.
8) Attach the belt.
9) Refer to “Chapter 11 7. Adjusting the Timing Belt Tension” and adjust the
belt tension.
10) Install the motor case and cover.
11) Install the belt cover.
8-2
Replacing the drive belt
!
CAUTION
The position will deviate when the belt is replaced. After replacing the belt,
return-to-origin must be carried out and the point data must be reset. Remem-
ber the relation of the installation positions when removing any parts.
1) Remove the end cover from the counter-motor end, and remove the upper
cover. (On robot models having a long stroke, pull off the upper cover with a
parallel movement in the axis movement direction.)
2) Refer to “Chapter 11 8-1. Replacing the motor”, and remove the motor. (This
step is not required if the motor is installed at horizontal position or lower
position.)
11-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
3) Remove cover 1.
Cover 1
4) FXYBX X-axis, SXYB X, Y axes
Remove the belt stay installation bolts (4 bolts, 2 stays), and remove the belt
stays from the table.
Belt stay installation bolt
Table
Belt stay
FXYBX Y-axis
Remove the two belt stay installation bolts, and remove the belt stay from the
table.
5) Remove the belt stay bolts (2 bolts, 2 stays), and remove the belt.
11-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
6) Attach the new belt.
7) First, lead the belt from the top of the idle pulley, and push it out with a
narrow rod, etc.
8) Next, lead the belt through the lower side of the slider and lead it to below the
drive pulley. Use a narrow rod, etc., to face the belt edge upwards.
9) Finally, mesh the belt between the drive pulley and drive pulley idler, and
turn the drive pulley.
10) Attach the belt stays to the belt.
11) Install the belt stays onto the slider table, and temporarily tighten the belt
stay installation bolts.
12) Refer to “Chapter 11 7. Adjusting the Timing Belt Tension”, and adjust the
belt tension.
13) Refer to “Chapter 11 6. Installing the Cover”, and install the upper cover.
14) Install the end cover.
11-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8-3
Replacing the speed reduction belt
!
CAUTION
The position will deviate when the belt is replaced. After replacing the belt,
return-to-origin must be carried out and the point data must be reset. Remem-
ber the relation of the installation positions when removing any parts.
1) Remove the belt cover.
2) Remove the four motor plate installation bolts.
Motor plate
installation bolt
3) Place the motor plate near the loose side, and remove the belt.
4) First, attach the new belt to the small pulley, and then fit it onto the large
pulley.
5) Refer to “Chapter 11 7-1-2. Adjusting the speed reduction belt tension”, and
adjust the tension.
6) Install the belt cover.
11-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8-4
Replacing the slider
If the X stroke is 2150mm or more for the FXYBX, or 2450mm or more for the
SXYBX, a slider mechanism is provided in the X-axis stroke cover. Use the fol-
lowing procedure if the slider needs to be replaced due to wear or damage.
1) Turn the controller power OFF.
2) Pull off the upper cover with a parallel movement in the axis movement di-
rection.
3) Remove the two slider installation bolts.
Slider installation bolt
4) Replace the slider, and temporarily tighten the two installation bolts.
5) Refer to "Chapter 11 6. Installing the cover", and install the upper cover.
6) Move the table two or three times along the full stroke.
7) Remove the 12mm diameter label attached to the upper cover on the counter-
motor side, and move the slider until the slider installation bolt is visible
from this hole.
Cover label
Bolt tightening hole
8) Tighten the slider installation bolts, and move the table again by approx.
20mm. Then, tighten the other slider installation bolts.
9) Attach the enclosed label to plug the hole.
11-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8-5
Replenishing the grease
8-5-1
Replenishing grease to the linear guide
The X-axis, Y-axis and Z-axis (ZF) use a linear guide as the linear guide mecha-
nism. Grease must be replenished to this linear guide periodically. Select the
grease from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
!
CAUTION
When the ZF unit is attached for the 3rd-axis, the replenishment work can be
carried out easier by moving the Z-axis slider to near the motor (near the origin)
and turning the controller power OFF.
!
CAUTION
If the X-axis stroke is 2150mm or more for the FXYBX, or 2450mm or more for
the SXYBX, a slider mechanism is provided in the X-axis stroke cover to sup-
port the inner self-weight.
When removing the X-axis stroke cover, do not pull it up and off. Instead, pull it
with a parallel movement in respect to the axis movement direction, to remove
the stroke cover from the slider. Then, pull it upward and off.
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the axis stroke cover when replenishing grease.
11-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
4) Using a grease gun, replenish grease from the grease nipple installed on the
linear guide bearings.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the linear guide bearings and rail.
FXYBX
X-axis, Y-axis
The X-axis has four bearings, and the Y-axis has two linear guide bearings.
Replenish grease to all bearings. Wipe off any excessive grease that has seeped
out to the rail.
Recommended grease gun
: MG70 (THK) N-type nozzle
SXYBX
X-axis, Y-axis
The X-axis and Y-axis each have four linear guide bearings.Replenish grease to
all four bearings.
Wipe off any excessive grease that has seeped out to the rail.
Recommended grease gun
: MG70 (THK) N-type nozzle
Z-axis (ZF)
One linear guide bearing is attached. A grease nipple is attached to the counter-
motor side of the slider, so move the slider to the motor side and then start the
work.
Recommended grease gun
: MG70 (THK) H-type nozzle
5) Install the stroke cover.
Confirm the surrounding safety, and then turn the controller power ON.
11-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8-5-2
Replenishing grease to the ball screw (ZF)
The ZF uses a ball screw for drive. Grease must be periodically replenished to the
ball screw. Refer to section 8-6. for details on replenishing grease to the ZS/ZRS
unit ball screw. Select the grease from the following recommended types.
Recommended grease
: Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
!
CAUTION
Always remove the grease nipple after completing the work. Damage or
positional deviation could occur if the robot is operated with the grease nipple
installed.
1) Prepare the following recommended grease nipple beforehand.
Recommended grease nipple : A-M6X1 type (JIS B1575)
2) Turn the controller power OFF.
NOTE
The replenishment work can be carried out easier by moving the Z-axis slider to
near the motor (near the origin) and turning the controller power OFF.
3) Place a sign indicating “Work In Progress” so that other operators do not turn
the controller power ON.
4) Remove the axis stroke cover when replenishing grease. (Refer to
"1. Installation" for details on removing the cover.)
5) Install the grease nipple onto the ball screw flange.
6) Replenish the grease from the grease nipple using the grease gun.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the ball screw nut and screw. Wipe off any exces-
sive grease.
Recommended grease gun : MG70 (THK) N-type nozzle
7) Remove the grease nipple.
11-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8-6
Periodic inspection of the ZS/ZRS unit
8-6-1
Replenishing grease to the Z-axis ball screw and ball spline
A ball screw drive is used for the ZS and ZRS vertical axis. Grease must be
replenished to this ball screw periodically. Select the grease from the following
recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the screws (M4, 6 screws) fixing the cover, and pull the cover up-
ward and off.
M4 screw
M4 screw
Fig. 11-22 ZS
4) Wipe off any excessive grease adhered on the ball screw shaft and ball spline shaft.
5) Apply a thin coat of grease on the screw shaft with a finger.
6) Return the cover to the original position.
11-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
8-6-2
Adjusting the R-axis belt tension (ZRS)
WARNING
There is a risk of injury if fingers, etc., are caught between the drive sec-
tion pulley and belt section. Always turn the controller power OFF and
carefully carry out the work if these parts may be contacted.
!
CAUTION
The position will deviate when the belt tension is adjusted.
Carry out absolute reset, and reset the basic coordinates and point data.
With the ZRS model, a timing belt is used for the R-axis.
If the timing belt tension is week, adjust the belt tension with the following pro-
cedures.
Push-pull scale
Deflection
Load
Pulley
Belt
Pulley
Fig. 11-23 Adjusting the belt tension
1) Turn the controller power OFF.
2) Place a sign indicating "Work In Progress" so that other operators do not turn
the controller power ON.
3) Remove the cover. (M4, 6 screws)
4) The following work must be carried out by two operators.
One operator must apply a vertical load on the center of the belt with the
push-pull scale, and the other operator must measure the belt deflection at
that time.
5) If the measured value is within the range shown below, there is no need for
adjustment. Adjust with the following procedure if the measured value is not
within the range.
Table 11-3
Load
4.4 to 4.8N ( 0.45 to 0.49kgf )
2mm
Deflection amount
6) Loosen the M4 bolt q (three positions) shown in Fig. 11-24.
11-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
7) If the value measured in step 4) is smaller than the value given in Table 11-3,
move the R-axis motor so that the tension increases. If larger than the value
in Table 11-3, move the R-axis motor so that the tension decreases. Then, fix
the bolts.
8) Measure the belt tension again with the procedure given in step 4).
If the measured value is within the range shown in Table 11-3, adjustment of
the R-axis belt tension is completed. If the measured value is not within the
range shown in Table 11-3, repeat steps 6) to 8) and adjust.
9) Tighten the M4 bolt q with the specified tightening torque.
.
.
Specified torque
4.5N m (46kgf cm)
10) Return the cover to the original position.
Tension decreases
qR-axis motor fixing bolt (M4)
Tension increases
R-axis motor
Fig. 11-24 ZRS belt tension
8-6-3
Replacing the R-axis harmonic drive (ZRS)
The ZRS R-axis speed reduction gear uses a harmonic drive.
The ZRS uses a harmonic drive as the R-axis speed reduction gear, which must
be replaced after using for a set period. Determine the harmonic drive replacement
period with the following procedure, and replace as required.
The ZRS harmonic grease uses a long-life type, and the grease does not need to
be replaced.
11-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 FXYBX/SXYBX
Replacement period
The harmonic drive replacement period is determined by the total number of
wave generator rotations. A calculation example is shown below.
The recommended harmonic drive replacement period is 8.4×108 rotations (at
usage atmospheric temperature range 0°C to +40°C).
The harmonic drive should be replaced earlier if the robot operation duty is high
or if the temperature conditions are poor.
[Replacement period]
=8.4×108/(n×60×h×D×N×θ) years
n
θ
N
h
: Number of robot movements in one minute
: Average axis rotation in one movement
: Deceleration rate (50 for ZRS R-axis)
: Number of operation hours per day
: Number of operation days per year
D
(Example) TheYK500X X-axis harmonic drive replacement period when the
axis rotates an average quarter turn every movement and the robot
moves ten times in one minute. (Operation hours: 24 hours/day,
number of operation days: 240 days/year)
n
: 10
θ
: 0.25
N
: 50
h
: 24
D
: 240
[Replacement period]
=8.4×108/(n×60×h×D×N×θ)
=8.4×108/(10×60×24×240×50×0.25)
=19.4 years
Consult with YAMAHA when actually replacing the harmonic drive.
11-39
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
11-40
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 12
HXYLX
1 Installation ............................................................................12-1
1-1 Installation method 1
(Arm type, moving arm type, pole type, gantry type X-axis) .......... 12-1
1-1-1 Installation bolt types .....................................................................12-1
1-1-2 Installation bolt nominal length ......................................................12-1
1-1-3 Tightening torque...........................................................................12-2
1-1-4 Installation methods ......................................................................12-2
1-2 Installation method 3 (Gantry type support axis) ........................... 12-5
2 Protective Connections.........................................................12-6
2-1 Ground terminal ............................................................................. 12-6
2-2 Ground wire ................................................................................... 12-7
2-3 Wiring methods .............................................................................. 12-7
3 Installing the Tool ..................................................................12-8
3-1 Arm type, gantry type 2-axis model ............................................... 12-8
3-2 Moving arm type 2-axis model ....................................................... 12-9
3-3 Pole type 2-axis model................................................................. 12-10
3-4 ZH
(Arm type, gantry type, moving arm type 3rd-axis option) ............12-11
3-5 ZL (Arm type, gantry type) ........................................................... 12-12
3-6 ZPH (Pole type 3rd-axis option)................................................... 12-13
3-7 RH (Arm type, gantry type 4th-axis option).................................. 12-14
Download from Www.Somanuals.com. All Manuals Search And Download.
4 User Wiring and User Piping ..............................................12-15
4-1 Cable carrier type......................................................................... 12-15
4-1-1 Example of wiring and piping methods using cable carrier .........12-15
4-1-2 Cable carrier specifications .........................................................12-17
4-1-3 User I/O cable specifications .......................................................12-18
4-2 Whipover cable type (moving arm type/pole type 3-axis) ............ 12-19
4-2-1 Examples of wiring and piping with Whipover cable ...................12-19
5 Periodic Inspections ...........................................................12-21
5-1 Replenishing grease to the linear guide....................................... 12-21
5-2 Replenishing grease to the ball screw ......................................... 12-22
5-3 Adjusting the timing belt tension (X-axis)..................................... 12-24
5-4 Replacing the motor (X-axis) ....................................................... 12-25
5-5 Installing and removing the cover ................................................ 12-27
5-5-1 Stroke cover ................................................................................12-27
5-5-2 Belt cover ....................................................................................12-28
5-5-3 Motor cover .................................................................................12-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
1
Installation
WARNING
Always turn the controller power OFF before installing the robot. Serious
accidents might occur if the robot starts to operate during installation.
Install the HXYLX by tapping holes into the installation base and securing the
robot to the base with M8 bolts from the inside of the robot. The installation
method is the same for the arm type, pole type, moving arm type and gantry type
X-axis. Note that the installation method differs for the gantry type support axis.
1-1
Installation method 1
(Arm type, moving arm type, pole type, gantry type X-axis)
Install the arm type, moving arm type, pole type and gantry type X-axis in the
following manner.
1-1-1
1-1-2
Installation bolt types
• Use the following type of installation bolt.
Hexagon socket head cap screw M6 Strength 8.8T
Installation bolt nominal length
WARNING
Do not use washers or spring washers with the tightening bolt.
The bolt head could interfere with the linear guide’s bearings and be dam-
aged.
If the installation base is made of steel, secure 1D or more (8mm or more for M8)
for the screw fitting length. When made of aluminum, secure 1.5D or more (12mm
or more for M8).
The frame thickness is 33mm. (Refer to Fig. 12-1.)
Recommended nominal length 45mm or more
Fig. 12-1
12-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
1-1-3
Tightening torque
• The accurate tightening torque will differ according to the seating face fric-
tional coefficient and the female screw material, etc. The following tightening
torque is recommended as a guide.
.
.
.
.
Recommended torque
22.5N m to 36.3N m (230kgf cm to 370kgf cm)
1-1-4
Installation methods
WARNING
Always use the designated bolt, and securely tighten it with the correct
torque. Failure to observe this could cause the robot position to deviate,
and could also lead to serious accidents.
1) Tap M8 coares screw thread holes into the installation base where the robot is
to be installed.
Refer to the XY-X Series catalog for the hole positions.
2) Remove the screws securing the upper cover of the robot and remove the
upper cover.
If necessary, move the slider to a location where it does not block the instal-
lation holes on the bottom of the robot frame.
12-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3) Secure the robot to the base with the specified bolts and torque.
The bolts and tightening torque are shown below.
Bolt
Hex socket-head M8 bolt, strength: 8.8T,
length: longer than 45mm (F17), longer than 50mm (F20)
Tightening torque 230kg-cm to 370kg-cm
WARNING
Be sure to tighten the bolt to the correct torque. The wrong torque may
not only cause robot position errors but also lead to serious accidents.
4) Reattach the upper cover after installing the robot.
Refer to Chapter 12 “5-5 Installing and removing the cover”, and install the
cover.
12-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
●Protective bonding
WARNING
Always ground the robot and controller unit to prevent electrical shock.
A grounding terminal (M4 screw) is provided inside the cable box, so always
ground the unit. The position of the grounding terminal is shown below.
Cable box
l
!
CAUTION
• A secure ground connection (less than 100-ohm resistance to ground) is rec-
ommended.
• Use electrical wire thicker than AWG14 (2mm2) as the ground wire.
WARNING
Always turn off the power to the controller before making the ground con-
nection.
Provide a terminal marked “PE” as the protective conductor for the entire sys-
tem, and connect it to an external protective conductor. Also securely connect
the ground terminal on the robot frame to the protective conductor.
(Symbol 417-IEC5019)
12-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
1-2
Installation method 3 (Gantry type support axis)
Install the gantry type support axis in the following manner.
!
CAUTION
Move the X-axis as much as possible, and tighten the bolts where the move-
ment is the lightest.
Set the X-axis and guide rail parallelism during installation. Make sure that
there is no difference in the height direction of the X-axis and guide rail installa-
tion surface.
1) Fix the robot onto the specified position of the installation base with bolts.
Do not tighten the guide rail bolt at this time. Securely fix the X-axis section
onto the installation base.
2) When the ZR-axis is provided, or if tools are already attached, move as
close to the X-axis side as possible so that a load is not applied on the
guide rail.
3) Loosen the bolt for theY-axis and support installation bracket. (Refer to
following drawing.)
4) Temporarily fix the guide rail onto the installation base with bolts.
The parallelism of the guide rail and X-axis must be set using a dial gauge or
pick gauge, etc.
5) To easily set the parallelism, first tighten the bolt loosened in step 3).
Set the X-axis near one end, and tighten the bolt on the guide rail end in this
state. Next, move the X-axis to the opposite end, and tighten the bolt on the
opposite side of the guide rail in this state. Repeat this until all bolts have
been tightened.
Y-axis
Support installation bracket
Guide rail stay
Bolts
Adjustment of gantry type support rail
12-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
2
Protective Connections
WARNING
Always ground the robot and controller to prevent electrical shocks.
WARNING
Always turn the controller power OFF before connecting the ground to
prevent electrical shocks.
WARNING
When using a tool or workpiece having power which could contact the
robot due to a failure or the specifications, the user must provide proper
grounding since the robot does not have a ground terminal for those
devices.
Refer to the following explanations and connect the robot side ground tap with
the external protective conductor's ground terminal using a ground wire.
2-1
Ground terminal
The ground terminal is located on the inside of the X-axis wiring box. (Refer to
Fig. 12-3.)
Cable box
Ground terminal
Robot cable
Cable carrier
Fig. 12-3
12-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
2-2
2-3
Ground wire
Use an AWG14 (2.0mm2) or larger ground wire with a total length of 1m or less.
Crimp an M4 ring-tongue terminal on the end of the wire connected to the robot.
Wiring methods
!
CAUTION
Accurately insert the lock washer between the ring-tongue terminal and robot.
Proper continuity may not be secured if the lock washer is dislocated.
1) Loosen the four M4 small screws, and open the X-axis wiring box cover.
2) Pass the ground wire through the cable lead-out port on the X-axis wiring
box (fixed).
Cable lead-out port
3) Connect the ring-tongue terminal of the ground wire to the ground terminal
on the robot.
An M4 small screw with spring washer and lock washer are attached to the
ground terminal.Arrange the parts in the order of the lock washer, ring-tongue
terminal and M4 small screw with spring washer, and then tighten. (Refer to
Fig. 12-4.)
M4 small screw with spring washer
Ring-tongue terminal
Lock washer
Fig. 12-4
12-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3
Installing the Tool
Install the user tool onto the robot’s tool installation surface in the following man-
ner.
WARNING
Always turn the controller power OFF before Installing a tool to prevent
an accident.
WARNING
Before installing a tool, check that the robot is securely fixed to the base.
WARNING
The user is responsible for determining the required bolt type and tight-
ening torque, and accurately installing the tool. Improper installation can
cause the tool to dislocate during operation and lead to serious accidents.
3-1
Arm type, gantry type 2-axis model
Eight M8 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider installation surface. (Refer to Fig. 12-5.) Install the user tool onto
the Y-axis slider using these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these to
fix light loads other than the tool, such as a wiring retainer.
4-M5×0.8 Depth12
(The same position on the
50
52.5
opposite surface at two locations)
2-φ6H7 Depth10
155
142
120
8-M8×1.25
Depth25
12.5
25 (Effective screw depth)
Fig. 12-5 HXYLX arm type, gantry type
12-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
Select the nominal length of the tool fixing bolt so that the fitting length of the
screw fixing the tool is 16mm or more, 25mm or less.(Refer to the cross-section
drawings in Fig. 12-5.)
!
CAUTION
If the fitting length is less than 16mm, the threads could be damaged during
tightening. Note that if the fitting length exceeds 25mm, the bolt end could con-
tact the cover.
3-2
Moving arm type 2-axis model
The moving arm type has an aluminum-cast bracket on the end of the Y-axis.
Install the tool on this bracket.
Twelve M8 coarse thread tap holes and two φ6 reamer holes are opened on the
bracket.
133
12.5
20
4-M8×1.25
63
2-φ6H7 Depth8
78
Fig. 12-6 HXYLX moving arm type
Select the minimum fixing bolt screw length so that the screw fitting length is
16mm or more.
!
CAUTION
If the fitting length is less than 16mm, the threads could be damaged during
tightening. If the fitting length is longer than 30mm, the screw could contact the
Y-axis.
12-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3-3
Pole type 2-axis model
Four M8 coarse thread tap holes and two $8 reamer holes are opened on the tool
installation surface of the Y-axis slider. (Refer to Fig. 12-7.) Install the user tool
onto the Y-axis slider using these holes.
Four M5 coarse thread tap holes are also opened on the slider side. Use these to
fix light loads other than the tool, such as a wiring retainer.
185
(Tolerance between knock (0.02)
12.5
4-M5×0.8 Depth15
2-φ8H7 Depth10
(The same position on the
opposite surface at two locations)
4-M8×1.25 Depth30
1.5 15
Fig. 12-7 HXYLX pole type
Select the under head length of the bolt fixing the tool so that the screw length
from the slider installation surface is 16mm or more, 30mm or less.
!
CAUTION
If the screw's fitting length is less than 16mm, the screw threads could be dam-
aged during tightening. If the screw length from the installation surface is longer
than 30mm, the screw end could contact the frame.
12-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3-4
ZH
(Arm type, gantry type, moving arm type 3rd-axis option)
When using the 3rd-axis model with ZH for the 3rd-axis, install the workpiece
onto the ZH frame in the following manner.
M6 coarse thread tap holes are opened on the frame's workpiece installation sur-
face. Install the tool using these holes. The tap depth is 10mm.
Select the under head length of the installation bolt so that the screw length from
the installation surface is 9mm or more, 27mm or less.
Refer to the XY-X Series catalog
for the M6 tap position.
100
22
22
78
Fig. 12-8 Tool installation ZH
NOTE
There is a step on the ZH frame.
The actual tool installation surface is the shaded section shown above.
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the screw length exceeds 27mm from the installation surface, the
screw could contact the bottom.
12-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3-5
ZL (Arm type, gantry type)
When using the 3rd-axis model with ZL for the 3rd-axis, install the workpiece
onto the ZL slider in the following manner.
Eight M6 coarse thread tap holes and two φ6 reamer holes are opened on the
Y-axis slider. (Refer to Fig. 12-9.) Install the user tool onto the ZL slider using
these holes.
Four M5 coarse thread tap holes are opened on the side of the slider. Use these to
fix loads other than the tool, such as the wire retainer.
23.5
19
2-φ6H7 Depth8
8-M6×1.0 Depth8
110
(Tolerance between knock (0.02)
4-M5×0.8 Depth7
135
20
90
20
Fig. 12-9 ZL
NOTE
There is a step on the top of the slider. The actual tool installation surface
is the shaded section shown above.
Select the nominal length of the bolt for fixing the tool so that the screw fitting
length is 6mm or more, 8mm or less. (Refer to the cross-section drawing in Fig.
12-9.)
!
CAUTION
If the fitting length is less than 6mm, the threads could be damaged during
tightening. If the fitting length is longer than 8mm, the end of the screw could
contact the cover stroke.
12-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3-6
ZPH (Pole type 3rd-axis option)
When ZPH is attached for the 3rd-axis of the pole type, install the tool onto the
aluminum bracket at the end of the ZP-axis.
Twelve M6 coarse thread tap holes and two φ6 reamer holes are opened on the
bracket.
100
70
44
2-φ6H7 Depth6
12-M6×1.0
32
20
10
Fig. 12-10 ZPH
Select the minimum nominal length of the fixing bolt so that the length is 9mm or
more from the tool installation surface.
!
CAUTION
If the fitting length is less than 9mm, the threads could be damaged during
tightening. If the bolt screw length exceeds 30mm from the installation surface,
the screw could contact the Y-axis.
12-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3-7
RH (Arm type, gantry type 4th-axis option)
!
CAUTION
When fixing with the tap holes, always fix at several holes. If fixed with only one
hole, the loosening torque could act during operation can cause loosening.
If the rotary axis RH is attached to the 4th-axis, install the tool onto the shaft at
the end of RH.
Five M8 coarse thread tap holes are opened on the end of the shaft. Install the tool
using these holes. The tool can also be installed with a bolt coupling or split
clamp using the outer diameter of the shaft.
φ35h7
φ38
φ75h8
0
φ98-0.2
5-M8×1.25
Depth20
(PCD. 20)
Fig. 12-11 RH
NOTE
The φ75 section shown below is the non-movable section. The rotary
shaft is the section below φ38.
12-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
4
User Wiring and User Piping
WARNING
Always turn off the controller before wiring and piping to prevent electri-
cal shocks.
4-1
Cable carrier type
A cable carrier is mounted as a standard between the X and Y axes. When 3rd-
axis are used, a cable carrier is also provided between theY and Z axes, and when
using 4th-axis, a cable carrier is also provided between the Z and R axes. Lay the
wiring and piping to the tool using these ducts. A 0.3sq 10-core flexible cable is
wired from the X-axis wiring box to the final axis wiring box, and can be used
freely. The wiring and piping methods for a 2-axis arm type are explained below
as an example.
4-1-1
Example of wiring and piping methods using cable carrier
1) Remove the four M4 small screws and open the X-axis wiring box (fixed)
cover.
2) Pass the required cables and air tubes, etc., through the cable lead-out port on
the X-axis wiring box (fixed).
Cable lead-out port
Fig. 12-12
12-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3) Remove the harness retainer located at the cable carrier outlet. (Hexagon
socket bolt M5, 2 bolts)
Harness retainer
4) Pass the required wires and pipes through the cable carrier.
The cable carrier has an outer lid that can be opened and closed easily. Use a
flat-tip screwdriver to open the lid. Press this lid in to close it.
5) Open the cover of the X-axis wiring box (movable), and lay the required
wiring and piping.
6)
!
CAUTION
1. The wires could be damaged if the harness retainer is tightened too much.
2. Manually move the robot by the full stroke before fixing to confirm that the
harness and air tube, etc., are not pulled in the cable carrier. These could be
damaged if pulled during operation.
When completed with the wiring, fix with the harness retainer in the wiring box.
7)
!
CAUTION
Take care not to catch the harness or air tube with the cover.
Return each wiring box cover to the original position.
12-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
4-1-2
Cable carrier specifications
!
CAUTION
When setting the harness and air tube into the cable carrier, make sure that the
total cross-sectional area of all wires and pipes, including the YAMAHA cable,
inside the cable carrier does not exceed 30% of the cable carrier’s cross-sec-
tional area. (This ratio is called the cable carrier space factor.)
The cross-sectional shape of the cable carrier, and the shape of the cable mounted
initially by YAMAHA are shown below.
2-axis specifications X-Y cable carrier
2-axis I/O specifications Y-axis cable carrier
User I/O wire φ10.1
Power wire φ9.8
Signal wire φ10.1
User I/O wire φ10.1
77
93
57
73
3-axis specifications X-Y cable carrier
3-axis specifications Y-Z cable carrier
Signal wire φ10.1
User I/O wire φ10.1
Power wire φ7.6
Power wire φ7.6
Power wire φ9.8
Signal wire φ8.2
User I/O wire φ10.1
Signal wire φ8.2
77
93
57
73
4-axis specifications X-Y cable carrier
4-axis specifications Y-Z cable carrier
Signal wire φ10.1
User I/O wire φ10.1
Power wire φ9.8
Power wire φ9.8
Power wire φ9.8
Signal wire φ11
Signal wire φ11
User I/O wire φ10.1
77
93
57
73
3-axis specifications Z-R cable carrier
4-axis specifications Z-R cable carrier
(ZRH)
Power wire φ7.6
Signal wire φ10.1
Signal wire φ8.2
Signal wire φ10.1
Power wire φ7.6
Signal wire φ10.1
Power wire φ7.6
Power wire φ7.6
(ZH)
(ZRL)
57
73
57
73
57
73
Fig. 12-13
12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
4-1-3
User I/O cable specifications
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
With the cable carrier specifications, signal wires (0.3mm2 × 10 wires) that can
be used freely by the user are laid as a standard between the X-axis wiring box
and final axis' wiring box.
Connectors and pins fitted onto the connectors on both ends of this signal wire
are also enclosed. Attach these to the user wiring to eliminate wiring led through
the robot.
Crimp the enclosed pins onto the user wiring, and insert into the connector.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
Refer to “1-2. User I/O wiring” in Chapter 5 “Specifications” for details on the
wiring specifications.
12-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
4-2
Whipover cable type (moving arm type/pole type 3-axis)
!
CAUTION
Do not clamp the wires or tubes to the outside of the independent cable. The
independent cable could sag or break and ultimately be disconnected.
The signal wires (0.3mm2 × 7 wires) and air tubes (4 × 2.5, 2 tubes) are incorpo-
rated in the Whipover cable. Use these to wire and pipe to the tool.
Signal Connector NO
NO Connector Remarks
Part No.
Part name
SM connector
SM connector
Contact
Part No.
SMR-10V-B
Qty.
1
Brown
Red
General-
purpose
I/O
I/O
q
1
2
3
1
2
I/O
w
1
2
3
4
5
Orange
Blue
3
4
SMP-10V-BC
1
4
5
6
7
SYM-001T-0.6
SHF-001T-0.8BS
7
Purple
Gray
5
6
Contact
7
White
Cable
1
7
8
8
9
9
10
10
P
P
BK
I/O
BK
t
qe
wr
I/O
ORG
ORG
M
M
Air tube
Air tube
Tool side
Controller side
Fig. 12-14 Whipover cable user-wire specifications
4-2-1
Examples of wiring and piping with Whipover cable
!
CAUTION
Securely crimp the pin and insert into the pin connector.
Failure to do so will prevent the signals and power from being supplied cor-
rectly, and may prevent the device from operating correctly.
1) Crimp the user's cable and tool wiring onto the enclosed connector.
Refer to section “1-2. User I/O wire” in Chapter 5 “Specifications” for de-
tails on the enclosed connector and pin specifications.
Recommended crimping tool YC-122R (J.S.T. Mfg Co., Ltd.)
2) When using an air tube, prepare an air coupler for connecting the user air
tube with the YAMAHA air tube.
12-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
3) Open the X-axis wiring box (movable) cover.
Y-axis wiring box
X-axis wiring box
(movable)
Fig. 12-15
4) Pass the required cables and air tubes, etc., through the X-axis cable conduit.
Crimp the enclosed connectors onto the cable.
5) Connect the connectors, and connect the air tubes using the air couplers.
6) Open the Y-axis wiring box cover.
7) Rubber grommets are also attached to the Y-axis wiring box.
Open holes in these grommets, and pass the tool side cables and air tubes
through.
8) Connect the connectors in the same manner as the X-axis, and connect the air
tubes with the air couplers.
9)
!
CAUTION
Take care not to catch the wiring or air couplers when installing the covers.
When completed with all wiring work, return each wiring box cover to the
original positions. Sandwich the X-axis wiring and air tube with the protec-
tive material at the wire lead-out port of each wiring box.
12-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
5
Periodic Inspections
WARNING
Always turn the controller power OFF before starting periodic inspec-
tions. Serious accidents could occur if the robot starts moving during the
periodic inspection.
WARNING
The motor and speed reduction gear casing are extremely hot after auto-
matic operation, so burns may occur if these are touched. Before han-
dling these parts, turn OFF the controller, wait for a while and check that
the part has cooled.
The inspection periods and general precautions are described in Chapter 4 Peri-
odic Inspections. Always refer to that Chapter before starting this work.
5-1
Replenishing grease to the linear guide
Grease must be replenished to this linear guide periodically. Select the grease
from the following recommended types.
Recommended grease : Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
1) Turn the controller power OFF.
2) Place a sign indicating “Work In Progress” so that other operators do not turn
the controller power ON.
3) Remove the axis stroke cover when replenishing grease.
Refer to section “1. Installation” for details on opening the X-axis stroke
cover.
12-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
4) Replenish the grease with one of the following methods.
Method 1: Using a grease gun, replenish grease from the grease nipple in-
stalled on the linear guide bearings.
Sufficient grease has been replenished when new grease starts to seep out
from the clearance between the linear guide bearings and rail.
The X-axis andY-axis each have four linear guide bearings. Replenish grease
to all four bearings.
Wipe off any excessive grease that has seeped out to the rail.
Recommended grease gun: MG70 (THK X-axis,Y-axis H-type nozzle)
(THK Z-axis (ZL) N-type nozzle)
Method 2: After wiping off the grease adhered on the rail and on the bear-
ing seal section with a rag, etc., apply a light coat of grease di-
rectly onto the guide rail with a finger.
NOTE
Due to the structure of ZH, grease can be replenished only with this
method.
When replenishing grease to ZH, turn the power OFF when near the
center of the stroke, and then apply grease to the top and bottom of the
guide.
5) Return the stroke cover to the original position.
5-2
Replenishing grease to the ball screw
Prepare the following recommended grease nipple beforehand.
Recommended grease nipple : A-M6X1 type (JIS B1575)
Recommended grease
: Alvania No. 2 (Showa Shell)
Daphne Eponex No. 2 (Idemitsu)
!
CAUTION
When designated by YAMAHA and the user, special grease, such as splatter-
proof grease, may be applied when the robot is delivered. In this case, apply
the appropriate grease as indicated in the delivery specification drawings, etc.
12-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
Replenishment methods
Refer to the following procedures and replenish the grease.
1) Remove the stroke cover of the axis to which grease is to be replenished.
2) Replenish the grease with one of the following methods.
!
CAUTION
Always remove the grease nipple after replenishing the grease. Failure to do
so could cause damage if the grease nipple and robot interfere.
Method 1: Install the grease nipple onto the M6 tap hole on the ball screw
flange surface, and replenish grease using the grease gun.
Sufficient grease has been replenished when new grease starts to seep out to
the screw shaft.
Wipe off any excessive grease.
Recommended grease gun : MG70 (THK H-type nozzle)
Method 2: Wipe off any grease adhered on the ball screw with a rag, etc.,
and directly apply grease into the ball screw slit with a finger.
NOTE
Due to the structure, the X-axis and ZH can be greased only with this
method.
3) Return the stroke cover to the original position.
12-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
5-3
Adjusting the timing belt tension (X-axis)
1) Temporarily tighten the motor installation bolt.
2) Remove the belt cover, and install the adjustment bolt (M5). Apply belt ten-
sion. (Refer to the following photograph.)
3) Tighten the motor fixing bolt.
4) As shown below, place the measuring instrument's head near the belt, and
pull the center of the belt span with a hexagon wrench, etc.
5) Refer to the following table, and adjust the belt tension.
Frequency
(Hz)
Span length Belt unit weight
Tension (N) Tension (kg)
(mm)
(kg/m)
100
207 to 219
88 to 98
9 to 10
0.051
6) When the appropriate tension has been set, tighten the motor installation bolt,
and measure the tension again.
(Note that the tension will increase as the bolt is tightened.)
7) Remove the adjustment bolt, and install the belt cover.
12-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
5-4
Replacing the motor (X-axis)
!
CAUTION
Since a positional shift occurs after replacing the motor, return-to-origin must
be performed again and the point data re-specified. When removing the parts,
check and mark the part positions versus each other so you can correctly reas-
semble the parts later.
1) Turn the controller power OFF.
2) Remove the belt cover and motor cover.
3) Open the cover of the box fixed onto the table slide, and disconnect the motor
wiring connector.
4) Remove the motor installation bolts (M6: four bolts).
Wiring box
Motor cable
Motor cover
Motor installation bolt
5) Pull the belt off the pulley. (Refer to the following photograph.)
Pulley
Belt
6) Remove the motor.
12-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
7) Remove the fixing bolts (M6: four bolts) from the pulley connection boss,
and pull the pulley off the motor.
(Loosen the bolts while fixing the surface machined section of the boss with
a pair of pliers, etc.)
4-M6
Hexagon bolt
Boss
Ring
Pulley
38
Motor
8) Replace the motor, and install the pulley onto the motor. (Refer to the photo-
graph above.) Take care to the orientation and order of the rings at this time.
9) Install the motor onto the block. Temporarily tighten the fixing bolts.
10) Install the belt.
Refer to section “5-3 Adjusting the timing belt”, and adjust the belt tension.
11) Install the motor cover and belt cover.
12) Connect the motor wiring connector, store inside the box, and install the
cover.
12-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
5-5
Installing and removing the cover
Stroke cover
5-5-1
Removing the stroke cover
1) Remove the fixing screws (M4, pan-head) on both ends.
2) Place the table slide near the stroke end, and pull off the cover.
Side cover
Center cover
Motor block
Table slide
End block
Installing the stroke cover
1) Place the table slide near the stroke end, and pass the cover between the table
slide and motor block.
2) Fix the cover to the end block. At this time, move the table slide to the stroke
center, and confirm that it does not interfere with the cover. If the table slide
interferes with the cover, adjust by tightening the cover fixing screw. (Refer
to following photographs.)
When cover contacts table slide
When cover contacts motor block
⇒ Tighten the cover fixing screw
⇒ Loosen the cover fixing screw
12-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
5-5-2
Belt cover
Removing the belt cover
1) Loosen the hexagon bolts (M4, two bolts) on the front with a spanner or
socket wrench. After removing the M4 screws on the top, pull the cover up-
ward and off. (Refer to the following photograph.)
M4 screw (two screws) M4 hexagon bolt (two bolts)
Installing the belt cover
1) Fit the cover so that the notch on the cover passes between the hexagon bolts.
Tighten the hexagon bolts with a spanner or socket wrench, and then fix from
above with the M4 screws.
12-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 HXYLX
5-5-3
Motor cover
Removing the motor cover
1) Cut the Insulock-tie binding the motor cable with a pair of nippers, and re-
move.
2) Remove the two M6 hexagon bolts, and pull the motor cover upward and off.
(Refer to the following photograph.)
Installing the motor cover
1) Insert the motor cover into the installation hole, and fix with two M6 hexa-
gon bolts.
2) Using the φ5 hole open on the motor cover, fix the motor cable with an
Insulock-tie.
12-29
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER'S MANUAL
Cartesian robot
Oct. 2006
Ver. 1.08
This manual is based on Ver. 1.07 of Japanese manual.
© YAMAHA MOTOR CO., LTD. IM Company
All rights reserved. No part of this publication may be reproduced in
any form without the permission of YAMAHA MOTOR CO., LTD.
Information furnished by YAMAHA in this manual is believed to be
reliable. However, no responsibility is assumed for possible
inaccuracies or omissions. If you find any part unclear in this manual,
please contact YAMAHA or YAMAHA sales representatives.
Download from Www.Somanuals.com. All Manuals Search And Download.
|