Operating Instructions
HOB
Contents
GB
Installation, 2-5
Positioning
Gas connection
GB
Data plate
English,1
Burner and nozzle specifications
Electrical connection,6
Description of the appliance, 7
Overall view
Start-up and use, 8-9
Practical advice on using the burners
Precautions and tips, 10
General safety
Disposal
Recycling & Disposal Information
GF750TX
GF761RFX
Maintenance and care, 11
Switching the appliance off
Cleaning the appliance
Gas tap maintenance
Troubleshooting, 12
Guarantee, 13
After Sales Service, 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Front
There is an adjustable L-shaped pipe fitting on the
GB
appliance supply ramp and this is fitted with a seal in
order to prevent leaks. The seal must always be replaced
after rotating the pipe fitting (seal provided with
appliance). The gas supply pipe fitting is a threaded 1/2
gas cylindrical male attachment.
Connecting a flexible jointless stainless steel pipe to a
threaded attachment
The gas supply pipe fitting is a threaded 1/2 gas
cylindrical male attachment.
Hooking position
for top H=40 mm
Back
These pipes must be installed so that they are never
longer than 2000 mm when fully extended. Once
connection has been carried out, make sure that the
flexible metal pipe does not touch any moving parts and
is not compressed.
! Use the hooks contained in the “accessory pack”
• Where the hob is not installed over a built-in oven, a
wooden panel must be installed as insulation. This
must be placed at a minimum distance of 20 mm from
the lower part of the hob.
! Only use pipes and seals that comply with current
national regulations.
Ventilation
Checking the tightness of the connection
To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (see diagrams).
! When the installation process is complete, check the
pipe fittings for leaks using a soapy solution. Never use a
flame.
Adapting to different types of gas
To adapt the hob to a different type of gas other than
default type (indicated on the rating plate at the base of
the hob or on the packaging), the burner nozzles should
be replaced as follows:
560 mm.
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of gas
(see table 1 “Burner and nozzle characteristics”).
! The hob can only be installed above built-in ovens with a
cooling ventilation system.
Gas connection
3. Reassemble the parts following the above procedure in
the reverse order.
The appliance should be connected to the main gas
supply or to a gas cylinder in compliance with current
national regulations. Before carrying out the connection,
make sure the cooker is compatible with the gas supply
you wish to use. If this is not the case, follow the
instructions indicated in the paragraph “Adapting to
different types of gas.”
4. Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.
When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.
! Check that the pressure of the gas supply is consistent
with the values indicated in Table 1 (“Burner and nozzle
specifications”). This will ensure the safe operation and
longevity of your appliance while maintaining efficient
energy consumption.
Connection with a rigid pipe (copper or steel)
! Connection to the gas system must be carried out in
such a way as not to place any strain of any kind on the
appliance.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the nozzles on separate “double flame “
burners:
3. Having adjusted the flame to the required low setting,
while the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out.
GB
1. remove the grids and slide the burners from their
housings. The burner consists of 2 separate parts (see
figure);
4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are
set to the low flame setting, increase this low flame
setting using the adjusting screw.
2. unscrew the burers with a 7 mm wrench spanner. The
internal burner has a nozzle, the external burner has
two (of the same size). Replace the nozzle with models
suited to the new type of gas (see table 1).
5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax or a similar
substance.
3. replace all the components by repeating the steps in
reverse order.
• Adjusting the burners’ primary air :
! If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.
Does not require adjusting.
! Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.
• Setting the burners to minimum:
1. Turn the tap to the low flame position.
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet pipe (in order
to comply with current national regulations).
2. Remove the knob and adjust
the adjustment screw, which is
positioned in or next to the tap
pin, until the flame is small but
steady.
DATA PLATE
Electrical
connections
see data plate
This appliance conforms to the
following European Economic
Community directives:
-2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent
amendments
- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility)
and subsequent amendments
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2009/142/EEC dated 30/11/09
(Gas) and subsequent
amendments.
- 2002/96/EC and subsequent
amendments.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Burner and nozzle specifications
GB
Table 1
Liquid Gas
Natural Gas
Thermal Nozzle Flow*
Burner
Diameter Thermal Thermal
By-Pass Nozzle
Flow*
g/h
(mm)
power
kW
power
kW
1/100
1/100
power
kW
1/100
l/h
(p.c.s.* (p.c.s.*)
(p.c.s.*)
Ridot.
Nomin.
(mm)
(mm)
***
**
Nomin.
(mm)
Reduced Fast (RR)
Semi Fast (S)
100
75
0.70
0.40
0.40
1.50
0.70
0.40
2.60
1.90
1.00
3.30
1.50
0.90
39
28
28
61
39
28
80
70
50
91
60
44
189
138
73
186
136
71
2.60
1.90
1.00
3.60
1.50
0.90
110 (Y)
106
248
181
95
Auxiliary (A)
55
79
Triple Crown (TC)
Semi-Fishburner (SP)
Double flame (DCDR internal)
130
—
240
109
65
236
107
64
145 (H1) 343
88
74
143
86
30
Double flame (DCDR external)
2 nozzle
130
1.50
4.10
61
70
298
293
4.10
110
390
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
Supply
Pressures
*
At 15°C and 1013 mbar - dry gas
**
***
Propane
Butane
Natural
P.C.S. = 50.37 MJ/Kg
P.C.S. = 49.47 MJ/Kg
P.C.S. = 37.78 MJ/m3
S
A
S
RR
DC
TC
SP
A
S
GF761RFX
GF750TX
! The hob can only be installed above built-in ovens with a cooling ventilation system.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Power supply voltage and frequency: 220-240V a.c.
50/60Hz.
rating of 45 amp. In this case the cable is not
supplied.
GB
Disposing of the plug
! The supply cable must be positioned so that it
never reaches at any point a temperature 50°C
higher than the room temperature. The cable must
be routed away from the rear vents. Should you
require it, you may use a longer cable, however, you
must ensure that the cable supplied with the
appliance is replaced by one of the same
specifications in accordance with current standards
and legislation.
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket. Instructions for
connecting cable to an alternative plug:
! The wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Your appliance is supplied with a 13 amp fused plug
that can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
If the colours of the wires in the mains lead do not
correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked “E”
or
or coloured Green or Green & Yellow.
! THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Connect Brown wire to terminal marked “L” or
coloured Red.
Connect Blue wire to terminal marked “N” or
coloured Black.
Replacing the fuse
If a 13 amp plug (BS 1363) is used it must be fitted
with a 13 amp fuse. A 15 amp plug must be
protected by a 15 amp fuse, either in the plug or
adaptor or at the distribution board. If you are in any
doubt about the electrical supply to your machine,
consult a qualified electrician before use.
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers
How to connect an alternative plug
The wires in this mains lead are coloured in
accordance with the following code:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
BLUE
“NEUTRAL” (“N”)
BROWN
“LIVE” (“L”)
GREEN AND YELLOW “EARTH” (“E”)
Removing the plug
GREEN &
YELLOW
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a cable
extension or to re-route the mains cable through
partitions, units etc., please ensure that either:
• the plug is replaced by a fused 13 amp re-
wireable plug bearing the BSI mark of approval.
or:
13 amp fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
• the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
Disposing of the appliance
When disposing of the appliance please remove the
plug by cutting the mains cable as close as
possible to the plug body and dispose of it as
described above.
Please note: for appliances with a rating greater
than 13 amp (eg: electric hob, double ovens and
freestanding electric cookers etc.) the mains cable
must be wired into a cooker output point with a
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the
appliance
Overall view
GB
GAS BURNERS
Support Grid for
COOKWARE
Control Knobs for
GAS BURNERS
SAFETY
DEVICES *
Ignition for
GAS BURNERS *
• GAS BURNER ignition* enables a specific burner
• GAS BURNERS differ in size and power. Use the
diameter of the cookware to choose the most
appropriate burner to cook with.
to be lit automatically.
• SAFETY DEVICE* stops the gas flow if the flame
is accidentally extinguished.
• Control Knobs for GAS BURNERS adjust the
power or the size of the flame.
Only available on certain models.
*
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up and use
! The position of the corresponding gas burner or
electric hotplate* is shown on every knob.
To turn on one of the rings, press the relative knob in
all the way and turn it anti-clockwise to the high
GB
setting
. The burner is fitted with an electronic
Gas burners
Each burner can be adjusted to one of the following
settings using the corresponding control knob:
igniter that automatically starts when the knob is
pressed in.
Since the burner is equipped with a safety device,
after lighting the burner keep the knob pressed in
for about 2-3 seconds to allow the device which
keeps the flame lit automatically to heat up.
The selected burner can be regulated using the
corresponding knob, as follows:
•
Off
Maximum
Minimum
•
Off
To light one of the burners, hold a lit match or lighter
near the burner and, at the same time, press down
and turn the corresponding knob anti-clockwise to the
maximum setting.
Maximum
Minimum
Since the burner is fitted with a safety device, the
knob should be pressed for approximately 2-3
seconds to allow the automatic device keeping the
flame alight to heat up.
When using models with an ignition button, light the
desired burner pressing down the corresponding
knob as far as possible and turning it anticlockwise
towards the maximum setting.
To switch off the burner, turn the knob in a clockwise
direction until it stops (when reaches the “•” position).
Practical advice on using the burners
To ensure the burners operate efficiently:
• Use appropriate cookware for each burner (see
table) so that the flames do not extend beyond the
bottom of the cookware.
• Always use cookware with a flat base and a
cover.
• When the contents of the pan reach boiling point,
turn the knob to minimum.
! If a flame is accidentally extinguished, turn off the
control knob and wait for at least 1 minute before
trying to relight it.
To switch off the burner, turn the knob in a clockwise
direction until it stops (when reaches the “•” position).
Burner
ø Cookware diameter (cm)
Reduced Rapid (RR)
Semi-Rapid (S)
24 - 26
16 - 20
10 - 14
16 - 20
24 - 26
The “separate double flame” burner*
This burner consists of two concentric burners which
can operate either together or separately.
Use of the double flame on the maximum setting gives
a very high power which reduces cooking times with
respect to conventional burners.
Moreover the double flame crown provides a more
uniform distribution of heat on the bottom of the pan,
when using both burners on minimum.
To ensure that the double-flame burner is used to
its full potential, never set the inside ring to
minimum and the outside ring to maximum at the
same time.
Pots and pans of all sizes can be used. In the case of
the smaller pots and pans we recommend the use of
only the internal burner.
Auxilliary (A)
Half-Fishburner (SP)
Triple Crown (TC)
Double flame (DCDR
internal)
10 -14
Double flame (DCDR
external)
26 - 28
! On the models supplied with a reducer shelf,
remember that this should be used only for the Double
flame internal (DCDR internal) burner when you use
casserole dishes with a diameter under 12 cm.
To identify the type of burner, refer to the designs in
the section entitled, "Burner and Nozzle
Specifications".
There is a separate control knob for each of the
“separate double flame” burners.
The knob marked by the symbol
external burner;
operates the
The knob marked by the symbol
internal burner.
operates the
Only available on certain models.
*
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Practical Advice on Using the Half Fish-Kettle
Burner *
GB
The two "Half Fish-Kettle" burners, are eliptic in form
and can be turned up to 90°. This makes the cooktop
more flexible in terms of how it can be used.
To turn the two burners 90°, proceed as follows:
• Make sure that the burners are cool;
• Lift the burner completely out of its housing;
• Replace it in its housing in the position desired;
• Make sure that the burners are positioned correctly
before use.
In addition, the two burners can be used in tandem or
speartely with cookware of different shapes and sizes:
• Double burner for a fish-kettle or oval cookware
(Fig.A).
• Double burner for a griddle or rectangular/square
cookware with minimum dimensions of 28x28 cm
(Fig.B)
• Single burner for medium size cookware (diameter
of 16-20 cm) (Fig.C).
• NEVER use the double burner in the configuration
represented in figure D.
Fig. A
Fig. B
Fig. C
Fig. D
Only available on certain models.
*
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and tips
! This appliance has been designed and manufactured in
compliance with international safety standards. The following
warnings are provided for safety reasons and must be read
carefully.
• Prevent children and the disabled from coming into contact or
having access at the ceramic glass cooking surface (if
present) immediately before and after use, as the cooking
surface will remain hot for at least a half hour after being turned
off;
GB
Generalsafety
• Contact service centers authorized by the manufacturer in the
event the ceramic glass cooking surface breaks.
• It is recommended that you follow the guidelines below:
• Disconnect the appliance from the electrical supply in the event
the ceramic glass cooking surface breakds.
• The appliance should not be operated by people (including
children) with reduced physical, sensory or mental capacities,
by inexperienced individuals or by anyone who is not familiar
with the product. These individuals should, at the very least,
be supervised by someone who assumes responsibility for
their safety or receive preliminary instructions relating to the
operation of the appliance.
• This is a class 3 built-in appliance.
• Gas appliances require regular air exchange to
maintain efficient operation. When installing the
hob, follow the instructions provided in the
paragraph on “Positioning” the appliance.
• These instructions are only valid for the
countries whose symbols appear in the manual
and on the serial number plate.
• The appliance was designed for domestic use inside the home
and is not intended for commercial or industrial use.
• The appliance must not be installed outdoors, even in covered
areas. It is extremely dangerous to leave the appliance exposed
to rain and storms.
• Do not let children play with the appliance.
• The appliance is not intended to be operated by
means of an external timer or separate remote-
control system.
• Do not touch the appliance with bare feet or with wet or damp
hands and feet.
• The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions outlined in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous. The
manufacturer may not be held liable for any
damage resulting from improper, incorrect and
unreasonable use of the appliance.
• Ensure that the power supply cables of other electrical
appliances do not come into contact with the hot parts of the
oven.
• The openings used for ventilation and dispersion of heat must
never be covered.
• Always make sure the knobs are in the “”/“” position when
the appliance is not in use.
• Whenunpluggingtheappliancealwayspulltheplugfromthe
mainssocket, donotpullonthecable.
• Never carry out any cleaning or maintenance work without
having detached the plug from the mains.
• In case of malfunction, under no circumstances should you
attempt to repair the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or further
malfunctioning of the appliance. Contact a Service Centre (see
Assistance).
• Always make sure that pan handles are turned towards the
centre of the hob in order to avoid accidental burns.
• Do not close the glass cover (if present) when the gas burners
or electric hotplates are still hot.
• Do not leave the electric hotplate switched on without a pan
placed on it.
• Do not use unstable or deformed pans.
• Remove any liquid from the lid before
opening it.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact
on human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance it must be
separately collected.
Consumers may take their old appliance to public waste
collection areas, other communal collection areas, or if national
legislation allows return it to a retailer when purchasing a
similar new product.
All major household appliance manufacturers are active in the
creation of systems to manage the collection and disposal of
old appliances.
Recycling&DisposalInformation
As part of Hotpoint's continued commitment to helping the
environment, Hotpoint reserves the right to use quality recycled
components to keep down customer costs and minimise material
wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door, plug and
cut mains cable off flush with the appliance. Dispose of these
parts separately to ensure that the appliance can no longer be
plugged into a mains socket, and the door cannot be locked shut.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Switching the appliance off
Gas tap maintenance
GB
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Over time, the taps may become jammed or difficult to
turn. If this happens, the tap must be replaced.
! This procedure must be performed by a qualified
Cleaning the appliance
technician authorised by the manufacturer.
! Do not use abrasive or corrosive detergents such as
stain removers, anti-rust products, powder detergents
or sponges with abrasive surfaces: these may scratch
the surface beyond repair.
! Never use steam cleaners or pressure cleaners on
the appliance.
• It is usually enough to wash the hob with a damp
sponge and dry it with absorbent kitchen roll.
• The removable parts of the burners should be
washed frequently with warm water and soap and
any burnt-on substances removed.
• For hobs which ligth automatically, the terminal part
of the electronic instant lighting devices should be
cleaned frequently and the gas outlet holes should
be checked for blockages.
• Stainless steel can be marked by hard water that
has been left on the surface for a long time, or by
aggressive detergents containing phosphorus.
After cleaning, rinse and dry any remaining drops
of water.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
It may happen that the appliance does not function properly or at all. Before calling the service centre for
assistance, check if anything can be done. First, check to see that there are no interruptions in the gas and
electrical supplies, and, in particular, that the gas valves for the mains are open.
GB
Problem
Possible causes/Solution
The burner does not light or the flame is not
even around the burner.
• The gas holes on the burner are clogged.
• All the movable parts that make up the burner are
mounted correctly.
• There are draughts near the appliance.
The flame dies in models with a safety device.
• You pressed the knob all the way in.
• You keep the knob pressed in long enough to activate the
safety device.
• The gas holes are not blocked in the area corresponding
to the safety device.
The burner does not remain lit when set to
minimum.
• The gas holes are not blocked.
• There are no draughts near the appliance.
• The minimum setting has been adjusted properly.
The cookware is unstable.
• The bottom of the cookware is perfectly flat.
• The cookware is positioned correctly at the centre of the
burner.
• The pan support grids have been positioned correctly.
If, despite all these checks, the hob does not function properly and the problem persists, call the nearest
Customer Service Centre. Please have the following information handy:
• The appliance model (Mod.).
• The serial number (S/N).
This information can be found on the data plate located on the appliance and/or on the packaging.
! Never use unauthorised technicians and never accept replacement parts which are not original.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
-
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
-
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOTAPPLY IF THEAPPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our
engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448
24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of
Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448 224
224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an
engineer to call.
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the
manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically
clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee you
must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use quality,
recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that
the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
06/2010 - 195084552.00
XEROX FABRIANO
GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|