OWNER’S/
OPERATOR’S
MANUAL
MODEL NO.’s
PLR-48 PLR-72
PLR-60 PBX-42
4 ft. Landscape Rake Shown
CAUTION
For Safe Operation
Read Rules And
Instructions Carefully
42” Box Scraper Shown
SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.
ATV or Garden Tractor
LANDSCAPE RAKE
BOX SCRAPER
STATEMENT
OF POLICY
It is the policy of Worksaver,
Inc. to improve its products
where it is possible and practical
to do so. Worksaver, Inc.
reserves the right to make
changes or improvements in
design and construction at any
time, without incurring the obliga-
tion to make these changes on
previously manufactured units.
Safety Instructions
Assembly & Mounting
Tractor Preparation
Operating Instructions
Maintenance
Repair Parts
CAUTION
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE
1. Select an area for assembly that is clean and free of any
debris which might cause persons working on the
assembly to trip.
6. After completing assembly, thoroughly inspect the
machine to be sure that all nuts, bolts, hydraulic fittings
or any other fastened assemblies have been thoroughly
tightened.
2. Do not lift heavy parts or assemblies. Use crane, jack,
tackle, fork trucks or other mechanical devices.
7. Before operating the machine, thoroughly read the
operation section of your operator’s manual.
3. Preview the assembly instructions in your operator’s
manual before proceeding further.
8. Before operating, read the maintenance section of your
operator’s manual to be sure that any parts requiring
lubrication, such as gearboxes, are full, to avoid any
possible damage.
4. If the assembly instructions call for parts or assemblies to
be blocked up, use only blocking material that is in good
condition and is capable of handling the weight of the
assembly to be blocked. Also insure that the blocking
material is on a clean, dry surface.
9. Before operating equipment – If you have any
questions regarding the proper assembly or
operation, contact your dealer or representative.
5. Never put hands, or any part of body, under blocked up
assemblies if at all possible.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION (continued)
All equipment is potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes potential hazards and follows reasonable safety practices.
When the use of hand tools is required to perform any part of assembly, installation, adjustment, maintaining,
repairing, removal, or moving the implement, be sure the tools used are designed and recommended by the
tool manufacturer for that specific task.
Personal protection equipment including safety glasses, safety shoes, and gloves are recommended during
assembly, installation, operation, adjustment, maintaining, repairing, removal, or moving of the implement.
Always use two people to handle heavy, unwieldy components during assembly, installation, removal, or
moving of the implement.
Never place any part of your body where it would be in danger if movement should occur during assembly,
installation, operation, maintaining, repairing, removal, or moving the implement.
Never place yourself between the tractor and implement while implement is in operation.
Do not work under a raised implement unless it is securely blocked or held in position.
A heavy load can cause instability of the tractor. Use extreme care during travel. Slow down on turns and
watch out for bumps. The tractor may need front counter-weights to counter-balance the weight of the
implement. An unstable tractor could steer badly and possibly tip over, causing injury or death.
Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating equipment.
Consult your doctor about operating tractor and implement while taking prescription medications.
Do not allow others to ride on the tractor with an operator. Riders are subject to injury such as being struck by
foreign objects or being thrown off. Riders obstruct the operator’s view resulting in unsafe operation. Never
allow anyone to ride on the implement!
Before you operate any implement, check over all pins, bolts and connections to be sure all are securely in
place. Replace any damaged or worn parts immediately.
Do not allow anyone who is not familiar with the safety rules and operation instructions to use this equipment.
Never allow children to operate or be around equipment.
Do not exceed capacity of the tractor or ATV.
Keep alert and watch the front as well as the rear when working with implements.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION (continued)
When maneuvering close to buildings or passing through narrow areas, be sure to allow sufficient clearance
for the implement and tractor.
Do not operate close to ditches or creeks. Slow down when operating over rough ground.
Always be sure the implement is in the fully raised position when in transport.
Pull from drawbar only. Failure to hitch properly could cause tractor to flip over, resulting in serious injury or
death.
Reduce speed on slopes and sharp turns to minimize tipping or loss of control. Be careful when changing
directions on slopes. Do not start or stop suddenly on slopes. Avoid operation on steep slopes.
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely, is in question -
DON’T TRY IT.
Avoid excessive speed during operation.
Make adjustments only when the implement is attached to the tractor.
Always ease the tractor into the load. It may be necessary to reposition and take less “bite” on the material to
move it safely.
Watch for and avoid hidden obstructions, i.e., buried pipes, rocks, concrete piers, uneven concrete slabs,
stumps, etc., when operating landscape rakes, box scrapers, or other ground engaging implements.
Never operate tractor and implement under trees with low hanging limbs. Operators can be knocked off the
tractor and then run over by the implement.
Stay alert for holes, rocks and roots in the terrain and other hidden hazards. Keep away from drop-offs.
Use extreme care and maintain minimum ground speed when transporting on hillside, over rough ground and
when operating close to ditches or fences. Be careful when turning sharp corners.
Pass diagonally through sharp dips and avoid sharp drops to prevent “hanging up” tractor and implement.
Practice will improve your skills in maneuvering rough terrain.
Always angle down slopes; never across the face. Avoid operation on steep slopes. Slow down on sharp turns
and slopes to prevent tipping and/or loss of control.
Always shut off tractor and shift to “Park” or set brakes when leaving tractor. Always lower implement to
ground. Remove key when leaving tractor unattended.
Before operating equipment: if you have any questions regarding the proper assembly or operation, contact
your dealer or representative.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS
Check the exploded view of the landscape rake or box
scraper in this manual to get an idea of the relationship
between the parts.
TRACTOR REQUIREMENTS
AND PREPARATION
The PLR Series landscape rakes and PBX-42 box
scraper are designed for small lawn/garden tractors and
ATV units equipped with a rear pull type hitch.
The two main subassemblies of the landscape rake are
heavy and awkward to handle. It is recommended that
you have one or two helpers to complete the assembly.
For the different width landscape rake units, we recom-
mend the following minimum size lawn/garden tractor:
It is suggested that you hook the clevis hitch of the main
frame to your tractor before assembling. If this in not
possible, block the hitch off the ground 5-6 inches.
Rake
Min. Tractor H.P.
PLR-48
PLR-60
PLR-72
10-12 H.P.
12-15 H.P.
15-18 H.P.
Slide the landscape rake tinebar assembly under the
main frame. Raise the front of the tinebar and block
below the angle tinebar. Insert the 1” x 4” hex head bolt
into the bottom of the center angle adjustment plate on
the tinebar and then through the 1” diameter hole in the
main frame. (Threaded end up). Place a 1” flat washer on
the bolt and then install the 1” nylock hex nut. Tighten this
nut until it is just lightly snug – you want to be able to
angle the tinebar but have a minimum amount of
looseness.
For the PBX-42 box scrapers, we recommend a 12-15
hp tractor.
ATV units need to have a low gear and be of sufficient
size (see the chart above for tractors and use a conver-
sion of 12 cc engine size equals 1 hp).
Small tractors may need wheel weights to have enough
traction.
To assemble the box scraper weldment, slide the box
scraper under the main frame and install the 1” hex head
bolt as described above for the landscape rake tinebar.
1
2
Then install the two / ” hex head bolts into the rear of the
main frame circle plate and the mounting bracket on the
box scraper. Tighten all bolts on the box scraper
attachment.
CAUTION!
Be sure tractor or ATV is in good condition. Read all
the safety precautions and make sure all operators
are familiar with the safety rules of operation.
On the landscape rake, set the desired angle of the
tinebar assembly and install the angle shift pin.
The operating height of the landscape rake and the box
scraper is set by the turnbuckle adjustment. If the unit is
on a flat level surface (concrete slab) you can set the
depth of operation by raising the wheels off the surface.
It is recommended that changes in operating depth be
kept small. After operating the attachment a few times,
you will get to know how much change your power unit
can handle.
PACKING
The landscape rake is usually shipped as two bundles:
1. Main Frame
2. Rake Tine Bar Assembly (teeth installed).
The box scraper is shipped as welded assembly.
Tie one end of the pull rope to the upper end of the lift
handle. The other end of the rope should be lightly tied to
your tractor or ATV.
ASSEMBLY
For instruction reference, the terms front or rear are
based on the operator facing forward on the tractor, thus
front is toward the front of the tractor and the rear is to
the rear of the tractor.
SAFETY . . .
YOU CAN LIVE WITH IT!
It is suggested that all the instructions be read before
beginning assembly.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS (continued)
As you operate the landscape rake or box scraper, you
SAFETY TRAINING
need to pull on the rope and pull the handle forward to
dump the material or to make a sharp turn. Releasing the
rope allows the implement to return to its depth setting as
controlled by the turnbuckle.
• Know your controls and how to stop tractor and engine
quickly in an emergency. READ THIS MANUAL AND
THE ONE PROVIDED WITH YOUR TRACTOR OR
ATV.
• To avoid accident or injury, do not allow anyone to
operate this equipment without proper instructions.
Any person who operates this equipment must be
instructed in and be capable of the safe operation of
the tractor, implement and all controls.
GRADING
Adjust the turnbuckle for the amount of cut you want to
take. Set the rake angle adjustment as desired – straight
for grading or angles for a windrowing effect.
It is recommended to operate the rake at a slow speed
(max. 3 mph) to give ample time for fine material to flow
through the tines.
When angle grading with the rake, the tinebar should be
angled only enough to allow material to slide across
easily.
• Do not allow children to operate this machine.
• Always wear relatively tight and belted clothing to
avoid entanglement in moving parts. Wear sturdy,
rough-soled work shoes and protective equipment for
eyes, hands, and hearing. Never operate tractor in
bare feet, sandals, or sneakers.
• Operate only in daylight or good artificial light.
LEVELING
The rake tinebar should be straight across (ie: 90˚ to the
line of travel). The gauge wheels will make the leveling
operation much easier. It will usually take several passes
over the same area to obtain the desired result.
• Ensure implement is properly mounted, adjusted and
in good operating condition.
• Ensure that all safety shielding and safety signs are
properly installed and in good condition.
RAKING
Light vegetative trash, dirt clods, or rocks may be raked
into piles or into windows for easier pick up. DO NOT
overload rake tines – remove large rocks, roots or limbs
before using the implement.
W ARNING!
L Be sure tractor engine is off and key is removed
before making any adjustments.
If you have a gravel or loose stone driveway, setting the
rake at an angle and making several passes in the grass
along each side of the drive will rake the stones out of the
grass and back into the driveway.
L Do not get under machine to make measurements
or adjustments without securely blocking imple-
ment first.
CAUTION!
Watch for and avoid catching the rake on stumps,
large rocks, or other immovable objects.
OPERATION
While standing by the landscape rake or box scraper,
pull forward on the handle and remove the transport lock
pin, then slowly release your pressure on the handle and
let the handle swing to the rear. Make sure your feet are
clear as the tinebar or box scraper lowers to the ground.
INCORPORATING SEED: Seed is best incorpo-
rated by making two passes in diagonal directions.
Consult your seed supplier or reference book for the
recommended seed depth. Set the rake straight and
operate the rake at two times the recommended seed
depth. Grass seed, for example, should be covered
There is an extra set of holes at the top of the lever
quadrant to store the transport lock pin while the imple-
ment is in use.
1
1
4
2
approximately / ”. Operate the rake at / ” penetration
and make two passes in diagonal directions.
To place the implement into the transport position, just
reverse the above procedure.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS (continued)
MAINTENANCE
STORING SAFELY
Straighten or replace any tines which may have bent
due to hitting buried or solid objects.
At the end of the working season or when the implement
will not be used for a long period, it is good practice to
clean off any dirt that may have accumulated.
Check the angle shift pin for excessive wear and
replace if necessary.
Inspect the implement for loose, damaged or worn parts
and adjust or replace if needed.
Repaint parts where paint is worn or scratched to
prevent rust.
Repaint parts where paint is worn or scratched to
prevent rust.
Check all bolts and nuts to be sure they are tight except
nylock nut pivot bolts – these should be just snug.
Store in a clean, dry place away from where children
play.
Periodically oil the following:
Turnbuckle threads
Pivot points
U Keep children away from danger all day, every day.
U Equip tractors with rollover protection (ROPS) and keep all
machinery guards in place.
U Please work, drive, play, and live each day with care and
concern for your safety and that of your family and fellow
citizens.
OBEY ALL
SAFETY WARNINGS!!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PLR LANDSCAPE RAKE
AND
PBX-42 BOX SCRAPER
PARTS DRAWING
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS.
AVOID NEEDLESS ACCIDENTS BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW.
•
•
Machinery should be operated only by those who are
responsible and are authorized to do so.
•
•
Reduce speed when transporting mounted implements to
avoid bouncing and momentary loss of steering control.
Stop the engine, lower all equipment, lock the brakes,
and remove the ignition key before dismounting from the
tractor.
A heavy load can cause instability of the tractor. Use
extreme care during road travel. Slow down on turns and
watch out for bumps. Tractor may need front counter-
weights to counter-balance the weight of the implement.
•
•
•
•
Never stand between tractor and implement while tractor
is being backed to hitch.
•
Reduce speed on hillsides or curves so there is no
danger of tipping.
Loose fitting clothing should not be worn, to avoid catch-
ing on various parts.
•
•
Avoid driving too close to the edge of ditches or creeks.
Detach implement in area where children normally do not
play.
Do not transport implement on public roads without
reflectors and slow moving vehicle emblem in daylight
and with approved warning lights at night and other
periods of poor visibility.
When performing adjustments or maintenance on an
implement, first lower it to the ground or block it securely
at a workable height.
•
•
•
Due to the width of some implements, use extra caution
on highways, farm roads, and when approaching gates.
•
•
•
Only a qualified operator should be permitted on tractor
when in operation; no riders allowed.
Always be sure the implement is in the proper position for
transport.
Make certain everyone is in the clear before starting
tractor or raising or lowering equipment.
Keep alert and watch the front as well as the rear when
working with the implement.
Operate the tractor and implement only while seated in
the driver’s seat.
Please work, drive, play and live each day with
care and concern for your safety and that of your
family and fellow citizens.
OWNER’S/
OPERATOR’S
MANUAL
MAKE EVERY DAY
A HOLIDAY FROM ACCIDENTS
MODEL NO.’s
PLR-48
PLR-60
PLR-72
PULL TYPE LANDSCAPE RAKE
PULL TYPE BOX SCRAPER
PBX-42
WORKSAVER LIMITED WARRANTY
W orksaver warrants its implements, parts and accessories to be free from defects
in materials and workmanship for a period of six (6) months from date of purchase.
Upon written approval, W orksaverwill repair or exchange without charge any part,
which upon examination by W orksaver or its authorized agent, shall disclose to be
defective.
This does not apply to (1) parts that have worn out in normal use, (2) parts broken
because of improper assembly or operation by the customer, (3) parts accidentally
damaged, (4) failure of parts traceable to improper care, (5) parts failing through use
of implement for purposes other than those for which it was designed.
The obligations assumed by W orksaverand the limitations expressed herein are in
lieu of all other warranties expressed or implied.
WHEN ORDERING
REPAIR PARTS, ALWAYS
GIVE THE FOLLOWING
INFORMATION:
1. PART NUMBER
2. PART DESCRIPTION
3. MODEL NUMBER
4. NAME OF ITEM
MARCH 2001
WORKSAVER, INC.
P.O. BOX 100 LITCHFIELD, IL 62056-0100 (217) 324-5973
WS-RP012-OG
Download from Www.Somanuals.com. All Manuals Search And Download.
|