®
240-VOLT
ELECTRIC DRYER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-253-1301.
or visit our website at...www.whirlpool.com
Table of Contents................................................. 2
8565592A
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
I
I
Read all instructions before using the dryer.
I
Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
I
Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
I
I
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
I
I
Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
I
I
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
I
I
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
I
I
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be exposed
to the weather.
See installation instructions for grounding requirements.
I
Do not tamper with controls.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
I
A grounded electrical outlet located within 2 ft (61 cm) of
either side of the dryer. See “Electrical Requirements.”
Tools and Parts
I
A sturdy floor to support the dryer weight (dryer and load) of
115 lbs (52 kg). The combined weight of a companion
appliance should also be considered.
Tools needed
Gather the required tools and parts before starting installation.
Read and follow the safety instructions provided with any tools
listed here.
I
A level floor with a maximum slope of 1" (2.5 cm) under entire
dryer.
I
I
I
I
I
Flat-blade screwdriver
Level
I
I
7 mm nutdriver
Do not operate your dryer at temperatures below 45ºF (7ºC). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. Drying times can be extended.
Caulking gun and
compound (for installing
new exhaust vent)
Adjustable wrench
T20 Torx screwdriver
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
I
I
Tin snips (new vent
installations)
Wire stripper (direct wire
installations)
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
Vent clamps
I
Wood block
Installation Clearances
The location must be large enough to allow the dryer door to
open fully.
Parts supplied
Remove parts package from the dryer drum. Check that all parts
listed are included.
Dryer Dimensions
39"
(99.1 cm)
*
23 ¹⁄₄"
(60.3 cm)
Coupling
Parts needed
Check local codes, existing electrical supply and venting, and
see “Venting Requirements” and “Electrical Requirements”
before purchasing parts.
33 ¼"
(84.45 cm)
Location Requirements
23 ³⁄₈ "
(59.37 cm)
WARNING
*Most installations require a minimum 5½" (14.0 cm) clearance
behind the dryer for the exhaust vent with elbows. See “Venting
Requirements.”
Minimum installation spacing for recessed area and closet
installation
Explosion Hazard
The following dimensions shown are for the minimum spacing
allowed when the dryer is to be operated with, or without, the
Stack Kit. To purchase a Stack Kit, see “Assistance or Service.”
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
I
Additional spacing should be considered for ease of
installation and servicing.
Failure to do so can result in death, explosion, or fire.
I
Additional clearances might be required for wall, door, and
floor moldings.
You will need
I
A location that allows for proper exhaust installation. See
“Venting Requirements.”
I
A separate 30-amp circuit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
I
I
Additional spacing of 1" (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
Electrical Requirements
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
It is your responsibility
I
To contact a qualified electrical installer.
I
To be sure that the electrical connection is adequate and in
conformance with the National Electrical Code, ANSI/NFPA
70-latest edition and all local codes and ordinances.
I
Companion appliance spacing should also be considered.
Recessed or closet installation - Dryer only
The National Electric Code requires a 4-wire supply
connection for homes built after 1996, dryer circuits involved
in remodeling after 1996, and all mobile home installations.
3"
14"
(35.6cm)
(7.6 cm)
A copy of the above code standards can be obtained from:
National Fire Protection Association, One Batterymarch Park,
Quincy, MA 02269.
48 in.2
(310 cm2)
18"(45.7cm)
I
To supply the required 3 or 4 wire, single phase, 120/240-volt,
60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt
electrical supply, if specified on the serial/rating plate) on a
separate 30-amp circuit, fused on both sides of the line. A
time-delay fuse or circuit breaker is recommended. Connect
to an individual branch circuit. Do not have a fuse in the
neutral or grounding circuit.
24 in.2
3"
3"
(7.6 cm)
(155 cm2)
(7.6cm)
0"
0"
(0cm)
0" (0cm)
(0cm)
B
C
A
I
I
Do not use an extension cord.
A. Side view - closet or confined area
B. Recessed area
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
C. Closet door with vents
Recessed or closet installation - Stacked with stack kit
(Accessory)
Electrical Connection
To properly install your dryer, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
3" (7.6 cm)
3"
12"
(30.5 cm)
I
This dryer is manufactured ready to install with a 3-wire
electrical supply connection. The green cabinet-grounding
conductor is permanently connected to the neutral conductor
(white wire) within the dryer. If the dryer is installed with a
4-wire electrical supply connection, the green cabinet-
grounding conductor must be removed from the external
ground conductor screw (green screw), and secured under
the neutral terminal (center or white wire) of the terminal
block. When the green cabinet-grounding conductor is
secured under the neutral terminal (center or white wire) of
the terminal block, the dryer cabinet is isolated from the
neutral conductor.
(7.6 cm)
48 in.2
(310 cm2)
DRYER
24 in.2
WASHER
3"
(155 cm2)
(7.6 cm)
0" (0 cm) 0" (0 cm)
1" (2.5 cm)
C
A
B
I
Use a 4-wire conductor cord when the dryer is installed in a
mobile home or an area where local codes do not permit
grounding through the neutral.
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
Mobile Home - Additional Location Requirements
This dryer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 245, HUD Part 280).
Mobile home installations require:
I
Metal exhaust system hardware which is available for
purchase from your dealer.
I
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
If using a power supply cord:
If connecting by direct wire:
Use a UL listed power supply cord kit marked for use with
clothes dryers. The kit should contain:
Power supply cable must match power supply (4-wire or 3-wire)
and be:
I
A UL listed 30-amp power supply cord, rated
120/240-volt minimum. The cord should be type SRD or
SRDT and be at least 4 ft (1.22 m) long. The wires that
connect to the dryer must end in ring terminals or spade
terminals with upturned ends.
I
Flexible armored cable or nonmetallic sheathed copper cable
(with ground wire), protected with flexible metallic conduit. All
current-carrying wires must be insulated.
I
I
10-gauge solid copper wire (do not use aluminum).
At least 5 ft (1.52 m) long.
I
A UL listed strain relief.
If your outlet looks like this:
GROUNDING INSTRUCTIONS
I
For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer uses a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
4-wire receptacle (14-30R)
Then choose a 4-wire power supply cord with ring or spade
terminals and UL listed strain relief. The 4-wire power supply
cord, at least 4 ft (1.22 m) long, must have 4, 10-gauge copper
wires and match a 4-wire receptacle of NEMA Type
14-30R. The ground wire (ground conductor) may be either green
or bare. The neutral conductor must be identified by a white
cover.
I
For a permanently connected dryer:
This dryer must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the dryer.
If your outlet looks like this:
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug on the power
supply cord: if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
3-wire receptacle (10-30R)
Then choose a 3-wire power supply cord with ring or spade
terminals and UL listed strain relief. The 3-wire power supply
cord, at least 4 ft (1.22 m) long, must have 3, 10-gauge copper
wires and match a 3-wire receptacle of NEMA Type 10-30R.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Direct Wire
Power Supply Cord
WARNING
WARNING
Fire Hazard
Fire Hazard
Use 10 gauge solid copper wire.
Use a new UL listed 30 amp power supply cord.
Use a UL listed strain relief.
Use a UL listed strain relief.
Disconnect power before making electrical connections.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center
terminal (silver).
Connect neutral wire (white or center wire) to center
terminal (silver).
Ground wire (green or bare wire) must be connected to
green ground connector.
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining 2 supply wires to remaining
2 terminals (gold).
Connect remaining 2 supply wires to remaining
2 terminals (gold).
Securely tighten all electrical connections.
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or
electrical shock.
Failure to do so can result in death, fire, or
electrical shock.
3. Unscrew the strain relief from the terminal block cover.
4. Unscrew the strain relief nut from the strain relief.
1. Disconnect power.
2. Remove the terminal block cover.
5. Put the power supply cord through the strain relief nut, then
A
the strain relief.
C
A
B
B
C
A. UL listed strain relief
B. Strain relief nut
C. Power cord
D
A. Terminal block cover
B. Strain relief
C. Center, terminal block screw
D. External ground conductor screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Replace strain relief (with power cord inserted) back into the
4-wire connection: Power supply cord
terminal block cover. Do not tighten strain relief nut.
B
A
A
D
F
E
C
B
C
A. 4-wire receptacle (NEMA type 14-30R)
B. 4-prong plug
C. Ground prong
D. Neutral prong
E. Spade terminals with upturned ends
F. Ring terminals
D
A. Terminal block cover
B. Strain relief
C. Strain relief nut
D. Power cord
1. Locate the neutral grounding wire (green with yellow stripes)
inside the dryer cabinet, behind the external ground
conductor screw. Remove this wire.
A
7. Now complete installation following instructions for your type
of electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
Electrical Connection Options
If your home has:
And you will be
connecting to:
Go to Section
A. Remove neutral grounding wire
(green with yellow stripes)
4-wire receptacle
(NEMA Type 14-30R)
A UL listed,
120/240 volt
minimum,
30 amp, dryer
power supply
cord
4-wire connection:
Power supply cord
2. Connect ground wire (green or bare) of power supply cord to
external ground conductor screw. Tighten screw.
3. Connect neutral wire (white or center wire) of power supply
cord under center screw of the terminal block.
4-wire direct
A fused
4-wire connection:
Direct Wire
disconnect or
circuit breaker
box
C
5"
(12.7 cm)
B
D
3-wire receptacle
(NEMA type 10-30R)
A UL listed,
120/240 volt
minimum,
3-wire connection:
Power supply cord
A
30 amp, dryer
power supply
cord
A. Neutral wire (white or center wire)
B. Center terminal block screw
C. External ground conductor screw
D. Ground wire (green or bare) of power supply cord
3-wire direct
A fused
3-wire connection:
Direct Wire
4. Connect the other wires to outer terminal block screws.
disconnect or
circuit breaker
box
Tighten screws.
5. Replace the terminal block cover on the back of the dryer.
6. Tighten strain relief nut.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the hooked ends of the other power supply cable wires
under the outer terminal block screws (hooks facing right).
Squeeze hooked ends together. Tighten screws.
4-wire connection: Direct Wire
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer
can be moved if needed.
Strip 5" (12.7 cm) of outer covering from end of cable, leaving
bare ground wire at 5" (12.7 cm). Cut 1¹⁄₂" (3.8 cm) from 3
remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of
wires into a hook shape.
6. Replace the terminal block cover on the back of the dryer.
7. Tighten strain relief nut.
3-wire connection: Power supply cord
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
When connecting to the terminal block, place the hooked end of
the wire under the screw of the terminal block (hook facing right),
squeeze hooked end together and tighten screw. See example
below.
B
D
A
E
F
C
A. 3-wire receptacle (NEMA type 10-30R)
B. 3-wire plug
C. Neutral prong
1. Locate the neutral grounding wire (green with yellow stripes)
inside the dryer cabinet, behind the external ground
conductor screw. Remove this wire.
D. Spade terminals with upturned ends
E. Neutral (white or center wire)
F. Ring terminals
A
1. Loosen or remove center terminal block screw.
2. Connect neutral wire (white or center wire) of power supply
cord under center screw of the terminal block. Tighten screw.
A. Remove neutral grounding wire
(green with yellow stripes)
B
A
2. Loosen or remove center terminal block screw.
3. Connect ground wire (green or bare) of power supply cord to
external ground conductor screw. (If power supply cord has
ring terminals, the ground conductor screw will need to be
removed to make the connection.) Tighten screw.
A. Neutral wire (white or center wire)
B. Center terminal block screw
3. Connect the other wires to outer terminal block screws.
4. Place the hooked end of the neutral wire (white or center wire)
of power supply cable under the center screw of terminal
block (hook facing right). Squeeze hooked end together.
Tighten screw.
Tighten screws.
4. Replace the terminal block cover on the back of the dryer.
5. Tighten strain relief nut.
C
B
D
A
A. Neutral wire (white or center wire)
B. Center terminal block screw
C. External ground conductor screw
D. Green or bare wire of power supply cable
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3-wire connection: Direct Wire
Venting Requirements
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
WARNING
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer
can be moved if needed.
Strip 3¹⁄₂" (8.9 cm) of outer covering from end of cable. Strip
insulation back 1" (2.5 cm). If using 3-wire cable with ground
wire, cut bare wire even with outer covering. Shape ends of wires
into a hook shape.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
When connecting to the terminal block, place the hooked end of
the wire under the screw of the terminal block (hook facing right),
squeeze hooked end together and tighten screw.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
4" (10.2 cm) heavy metal exhaust vent and clamps must be used.
DURASAFE™ vent products are recommended.
DURASAFE™ vent products can be purchased from your dealer
or by calling Whirlpool Parts and Accessories. For more
information, see the “Assistance or Service” section of this
manual.
1. Loosen or remove center terminal block screw.
2. Place the hooked end of the neutral wire (white or center wire)
of power supply cable under the center screw of terminal
block (hook facing right). Squeeze hooked end together.
Tighten screw.
I
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, or a concealed space of a building.
I
I
Do not use an exhaust hood with a magnetic latch.
Do not install flexible metal vent in enclosed walls, ceilings or
floors.
I
Use clamps to seal all joints. Exhaust vent must not be
connected or secured with screws or other fastening devices
which extend into the interior of the duct. Do not use duct
tape.
B
A
IMPORTANT: Observe all governing codes and ordinances.
A. Neutral wire (white or center wire)
B. Center terminal block screw
Improper venting can cause moisture and lint to collect
indoors, which may result in:
3. Place the hooked ends of the other power supply cable wires
under the outer terminal block screws (hooks facing right).
Squeeze hooked ends together. Tighten screws.
Moisture damage to woodwork, furniture, paint,
wallpaper, carpets, etc.
Housecleaning problems and health problems.
Use a heavy metal vent. Do not use plastic or metal foil vent.
Rigid metal vent is recommended to prevent crushing and
kinking.
Flexible metal vent must be fully extended and supported when
the dryer is in its final position. Remove excess flexible metal vent
to avoid sagging and kinking that may result in reduced airflow.
4. Replace the terminal block cover on the back of the dryer.
5. Tighten strain relief nut.
An exhaust hood should cap the vent to prevent rodents and
insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground or
any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, etc.).
If using an existing vent system, clean lint from the entire length
of the system and make sure exhaust hood is not plugged with
lint. Replace any plastic or metal foil vent with rigid metal or
flexible metal vent.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Determine vent length
1. Select the route that will provide the straightest and most
direct path outdoors. Plan the installation to use the fewest
number of elbows and turns. When using elbows or making
turns, allow as much room as possible. Bend vent gradually
to avoid kinking. Avoid 90° turns when possible.
Plan Vent System
Typical installations vent the dryer from the rear of the dryer.
A
good
better
B
2. Determine vent length.
The maximum length of the exhaust system depends upon:
I
I
I
The type of vent (rigid metal or flexible metal).
The number of elbows used.
Type of hood.
C
Recommended hood styles are shown here.
A. Exhaust hood
B. Flexible metal vent or rigid metal vent
C. Elbow
B
Alternate installation for close clearances
A
Venting systems come in many varieties. Select the type best for
your installation. A close-clearance installation is shown below.
Refer to the manufacturer’s instructions.
4"
(10.2 cm)
4"
(10.2 cm)
A. Louvered style
B. Box hood style
The angled hood style (shown following) is acceptable.
4"
(10.2 cm)
Over-The-Top installation (also available with one offset elbow)
Over-The-Top Installation Kit Part Number 4396028 for close
clearance alternate installation is available for purchase. For
ordering information see “Assistance or Service.”
2½"
(6.4 cm)
See the Vent Length Chart that matches your hood type for
the maximum vent lengths you can use.
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
Exhaust systems longer than specified will:
I
I
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and
increased energy usage.
3. Determine the number of elbows you will need.
IMPORTANT: Do not use vent runs longer than those specified in
the Vent Length Chart.
In the column listing the type of metal vent you are using (rigid
metal or flexible metal), find the maximum length of metal vent on
the same line as the number of elbows.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Vent Length Chart
2. Turn the coupling and exhaust vent assembly
counterclockwise in the exhaust hole on the back of the
dryer.
Number of
90º turns
or elbows
Type of vent
Box or
louvered
hoods
Angled
hoods
0
1
2
Rigid metal
90 ft (27.4 m) 80 ft (24.4 m)
64 ft (19.5 m) 58 ft (17.7 m)
Flexible metal
Rigid metal
Flexible metal
80 ft (24.4 m)
70 ft (21.3 m)
58 ft (17.7 m) 52 ft (15.8 m)
3. Make sure the exhaust vent is placed inside the exhaust hood
and then secured to the exhaust hood with a 4" (10.2 cm)
vent clamp.
Rigid metal
Flexible metal
70 ft (21.3 m) 60 ft (18.3 m)
50 ft (15.2 m) 42 ft (12.8 m)
WARNING
Install Vent System
Excessive Weight Hazard
1. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
2. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
3. Run vent to dryer location. Use the straightest path possible.
See “Determine vent length.” Avoid 90º turns. Use clamps to
seal all joints. Do not use duct tape, screws or other fastening
devices that extend into the interior of the vent to secure
vent.
4. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
Complete Installation
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
Level Dryer
Check the levelness of the dryer. Check levelness first
side to side, then front to back.
2. Check to be sure you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check the dryer’s final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level. See “Level Dryer.”
6. Plug into a grounded outlet. Turn on power.
7. Remove the clear protective film on the front edge and any
tape remaining on the dryer.
8. Read “Dryer Use.”
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
NOTE: It might be necessary to level the dryer again after it has
been moved into its final position.
10. Set the dryer on a full heat cycle (not an air cycle) for
20 minutes and start the dryer.
If the dryer will not start, check the following:
Connect Vent
I
I
I
I
I
Controls are set in a running or “On” position.
Start button has been pushed firmly.
Dryer is plugged into a grounded outlet.
Electrical supply is connected.
1. Using the coupling supplied with the dryer, connect the
exhaust vent to the coupling and secure with a 4" (10.2 cm)
vent clamp. See Illustration below.
House fuse is intact and tight, or circuit breaker has not
tripped.
I
Dryer door is closed.
E
A
C D
B
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat.
A. Coupling
B. Vent clamp
C. Vent coupler
D. Vent clamp
If you do not feel heat, turn off the dryer and check the
following:
I
There may be 2 fuses or circuit breakers for the dryer. Check
to make sure both fuses are intact and tight, or that both
circuit breakers have not tripped. If there is still no heat,
contact a qualified technician.
E. Rigid or flexible metal vent
If connecting to existing vent, make sure the vent is clean.
NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER USE
IMPORTANT: For best performance, do not use fabric softener
sheets in this dryer. You may use liquid fabric softener in the
washer.
Starting Your Dryer
1. Clean the lint screen before or after each cycle. See
“Cleaning the Lint Screen.”
WARNING
2. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
3. Press the POWER button to turn the dryer on. The indicator
light will glow to indicate that the power is on.
4. Press the TEMPERATURE button to select the recommended
temperature setting for the type of load being dried. See
“Temperature Control.”
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
5. Turn the cycle knob to the recommended setting for the type
of load being dried. See “Drying, Cycle, and Temperature
Tips.”
Do not dry anything that has ever had anything
flammable on it (even after washing).
6. After a short beep sounds, press the START button.
Failure to follow these instructions can result in death,
explosion, or fire.
Stopping and Restarting
To stop your dryer at any time
Turn the cycle knob to the STOP position or open the door.
To restart the dryer
1. Close the door.
2. Select a new cycle and temperature (if desired).
3. After the beep sounds, press the START button.
WARNING
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Do not dry items containing foam, rubber, or plastic in
this dryer.
Doing so can result in death or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Cycles and Temperatures
Cycles
To change the cycle or temperature after pressing START
1. Open the dryer door.
2. Press the TEMPERATURE button to change the temperature
(if desired).
3. Turn the cycle knob to the new desired position.
4. After the beep sounds, press the START button.
Drying, Cycle, and Temperature Tips
Select the correct cycle and temperature for your load.
Your dryer tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle and to
reduce wrinkling. After the cool-down cycle ends, the light
flashes and an end-of-cycle signal sounds to indicate the cycle is
complete.
Cycle Control knob
Drying tips
Automatic Cycles
I
Follow care label directions when they are available.
Automatic cycles may be used for most loads. Automatic cycles
give the best drying results in the shortest time. Drying time
varies according to the type of fabric, size of the load, and
dryness setting.
I
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
I
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
After drying a load, check the dryness.
I
If the load is drier than you like, select a setting closer to Less
Dry the next time you dry a similar load.
Cycle and temperature tips
I
I
If a load is not as dry as you like, complete drying using a
Timed cycle. Select a setting closer to More Dry the next time
you dry a similar load.
Dry most loads using an automatic cycle.
I
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
See following table for recommended cycles and temperature
settings.
Fabric Type
Cycle
Temperature
Setting
REGULAR
Heavy cottons and demins
Cottons and linens
SYNTHETICS
More Dry
Normal
Normal
Normal
White and colorfast
permanent press
Normal
Low
Low
Low
Low
White and colorfast items
that require ironing
Less Dry
Damp Dry
Damp Dry
Polyester/acrylic blends,
rayon, acetate
Washable silk and nylon
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Timed Dry
End of Cycle Signal
Use this cycle to get up to 60 minutes of heated drying time or to
complete drying if items are still damp after the automatic cycle.
Timed Dry is also useful for:
The dryer sounds a signal to let you know when the cycle is
finished. The signal is not adjustable and cannot be turned off.
The signal is helpful when you are drying permanent press,
synthetics, and other items that should be taken out as soon as
the dryer stops.
I
Heavyweight items and work clothes that require a long
drying time.
I
Lightweight items, such as lingerie, blouses and knits that
require a short drying time.
Anti-Wrinkle
See following table for recommended cycles and temperature
settings.
Anti-Wrinkle helps prevent wrinkles that form when clothes are
not removed promptly at the end of a cycle. Anti-Wrinkle tumbles
the load every minute until the cycle knob is set to the Stop
position or the dryer door is opened.
Fabric Type
Time
(minutes)
Temperature
Setting
During Anti-Wrinkle, the End of Cycle Signal will sound until the
cycle knob is set to the Stop position or the dryer door is opened.
Heavy cottons and denims
Cottons and linens
60
40
40
Normal
Normal
Low
Temperature Control
White and colorfast
permanent press
Temperature Control Button
White and colorfast items
that require ironing
40
40
40
Low
Low
Low
The Temperature Control button lets you select between a normal
and low drying temperature.
Polyester/acrylic blends,
rayon, acetate
NOTE: Always refer to the care label on the garment to determine
whether it can be tumble dried.
Washable silk and nylon
Normal
The Normal temperature setting is for sturdy fabrics, such as
cotton, linen and denim. If the Temperature Control button is not
pressed in, the temperature setting is Normal.
Low
The Low setting is for synthetics, such as cotton/polyester blend,
rayon, acetate, washable silk or nylon. If the Temperature Control
button is pressed in, the temperature setting is Low.
DRYER CARE
Cleaning the Dryer Location
Cleaning the Lint Screen
Every load cleaning
Keep dryer area clear and free from items that would obstruct the
flow of combustion and ventilation air.
The lint screen is located in the door opening of the dryer. Clean it
before each load. A screen blocked by lint can increase drying
time.
WARNING
To clean
1. Open the door and pull the lint screen straight up.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
2. Open lint screen.
3. Roll lint off the screen with your fingers. Do not rinse or wash
Failure to do so can result in death, explosion, or fire.
screen to remove lint. Wet lint is hard to remove.
4. Close lint screen. Push the lint screen firmly back into place
and close the door.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT:
I
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
Cleaning the Control Panel
To clean the control panel, use only a warm, damp cloth.
NOTE: Do not use abrasive cleaners or scouring pads on the
outer surfaces because they will scratch the finish and could
remove the writing on the control panel.
I
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other
towels, causing your dryer’s lint screen to fill up faster. Be
sure to remove lint from the lint screen before and after drying
new towels.
Some paper towels may also scratch the finish.
Removing Accumulated Lint
As needed cleaning
From Inside the Dryer Cabinet
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
Clean the lint screen with a nylon brush every 6 months, or more
frequently if it becomes clogged due to a residue buildup.
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
To wash
1. Roll lint off the screen with your fingers.
2. Wet both sides of the lint screen with hot water.
Vacation and Moving Care
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
Vacation care
Operate your dryer only when you are at home. If you will be on
vacation or not using your dryer for an extended period of time,
you should:
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
Moving care
For power supply cord-connected dryers:
4. Rinse with hot water.
1. Unplug the power supply cord.
5. Thoroughly dry lint screen with a clean towel. Replace in
2. Make sure leveling legs are secure in dryer base.
3. Use masking tape to secure dryer door.
dryer.
Cleaning the Dryer Interior
WARNING
To clean dryer drum
1. Make a paste with powdered laundry detergent and very
warm water.
2. Apply paste to a soft cloth.
OR
Apply a liquid, nonflammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
Electrical Shock Hazard
Disconnect power before servicing.
3. Wipe drum thoroughly with a damp cloth.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items inside-
out to prevent dye transfer.
For direct-wired dryers:
1. Disconnect wiring.
2. Make sure leveling legs are secure in dryer base.
3. Use masking tape to secure dryer door.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Clothes are not drying satisfactorily
Unusual sounds
I
I
The compact dryer operates at a lower wattage. Expect
longer drying times.
I
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
Check the following:
Is the lint screen clogged with lint?
Lint on load
Is the lint screen clogged with laundry detergent residue or
other residue? Wash the lint screen. See “Cleaning the Lint
Screen.”
I
I
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. See “Installation Instructions.”
Is the load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
I
I
Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.
Was the load overdried?
Is the exhaust vent crushed or kinked? Replace with heavy
metal or flexible metal vent. See “Installation Instructions.”
Use correct dryer settings for load type. Overdrying can
cause lint-attracting static electricity. See “Drying, Cycle, and
Temperature Tips.”
Is the automatic cycle ending early? This cycle will end early
if dryer load is not contacting the sensor strips. Level the
dryer. See “Installation Instructions.”
I
I
Was paper or tissue left in pockets?
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and
laundering.
I
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
Stains on load or color change
I
I
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water
and with items that hold moisture (cottons).
I
I
Were items soiled when placed in the dryer?
Items should be clean before being dried.
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from
noncolorfast items.
Dryer will not run
Items shrinking
I
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
I
I
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Has a fuse blown, or has a circuit breaker tripped?
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Is the motor running but the drum isn’t turning? This usually
means a belt is broken. Call for service.
Is the indicator light glowing? If not, press the POWER
button.
Was the START button firmly pressed?
Is a cycle selected?
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Loads are wrinkled
Odors
I
I
Was the load removed from dryer at the end of the cycle?
I
I
Have you recently been painting, staining, or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
I
I
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Is the dryer being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
Was the wash temperature too warm for the load being
washed?
Use a lower wash temperature, especially for permanent
press and delicate items.
Garment damage
I
Check the following:
Were zippers, snaps, and hooks left open?
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
I
I
I
Use and maintenance procedures.
Accessory and repair parts sales.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
I
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only FSP® replacement parts. FSP® replacement parts will fit
right and work right because they are made with the same
precision used to build every new WHIRLPOOL® appliance.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
To locate FSP® replacement parts in your area, call our Customer
eXperience Center telephone number or your nearest Whirlpool
designated service center.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
In the U.S.A.
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Call the Whirlpool Customer eXperience Center
toll free: 1-800-253-1301.
Benton Harbor, MI 49022-2692
Our consultants provide assistance with:
Please include a daytime phone number in your correspondence.
I
Features and specifications on our full line of appliances.
I
Installation information.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WHIRLPOOL® DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor costs to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4" (10.2 cm) metal exhaust vent must be used. Refer
to the venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Outside the 50 United States, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another
warranty applies.
If you need service, first see “Troubleshooting.” Additional help can be found by checking “Assistance or Service,” or by calling our
Customer eXperience Center at 1-800-253-1301, from anywhere in the U.S.A., or write: Whirlpool Corporation, Customer eXperience
Center, 553 Benson Road, Benton Harbor, MI 49022-2692.
8/04
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label, located on the inside door well of your dryer.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
8565592A
© 2004 Whirlpool Corporation.
9/04
Printed in Italy
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|