Operating Data
Owner's Manual
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by authorized
personnel, qualified in pool/spa installation. Improper installation and/or operation can
create a hazard which can cause serious injury, property damage, or death. Improper
installation and/or operation will void the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 1
SECTION 1.
Safety Information
1A. Safety Instructions
READ AND FOLLOW THESE SAFETY INSTRUCTIONS!
PLEASE SAVE THESE INSTRUCTIONS
Caution
1. Handrails which extend into the water must be removed or substituted with a figure four
design so as not to obstruct the movement of the cleaner.
2. Ladders present a special situation requiring our special Ladder Guard Kit. If the ladder
guard is not installed on the cleaner head, the unit can become entangled in the ladder.
3. Ideal pool are those with curved corners with a radius of at least 6" including all step and
love seat areas. Pools with square corners or corners with less than 90° angles (espe-
in step or love seat areas) can cause problems.
cially
4. Never install the pool cleaner in pools which have obstacles such as islands, stools, or
non-removable fountains, as the cleaner can become entangled.
FOR LONGER RAY-VAC® LIFE
To maximize the life expectancy of your Ray-Vac®
1. Never operate the Ray-Vac® with people in the pool.
2. Remove the pool cleaner from the pool and lay it out straight whenever you super
chlorinate your pool (high concentrations of chlorine CAN damage the hoses).
3. If a wheel is severely worn, broken, or missing, turn off the Ray-Vac® and do not
operate until wheel has been replaced.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 2
Jandy Ray-Vac®
3.
4.
Place the Ray-Vac on its back. Locate the two (2)
debris compartment latches. Rotate latch to open
position (see Fig 2).
SECTION 2.
General Information
2A. Introduction
While holding the Ray-Vac head down, firmly
grasp debris compartment cover. Pull the debris
compartment cover up and away from the tail
section to remove (see Fig 3).
The Jandy Ray-Vac® automatic pool cleaner is
designed to both vacuum and sweep your swimming
pool. The cleaner head moves in a random submerged
pattern about the pool, traveling, vacuuming and
cleaning from the pool floor to the water line. Its pattern
is determined by the shape of the pool, the
5.
Pull the screen up and away from the tail section
to remove (see Fig 4).
hydrodynamics of the cleaner design, adjustments of the
water pressure, and the forward and backward motion
created by the patented backup jet system.
The pool cleaner, by the use of its large suction
mouth, will vacuum dirt, leaves, and debris and store it
in its own chamber located in the cleaner head. In
addition, its drive jets are angled slightly downward
creating a powerful jet action to sweep any small debris
down to the main drain where it is removed by the filter
system.
Debris Compartment
Latches
In most typical residential pools, the pool cleaner
will eliminate 90% or more of the manual labor
involved in cleaning the pool. Because many of the
factors present in a swimming pool, such as shape of the
pool, location of the return lines, mounting point of the
cleaner, etc., there may be small areas where dirt tends
to collect. Usually, these areas are small and are
considered normal.
Figure 2. Open Debris Compartment Latches
Debris Compartment
SECTION 3.
Emptying the Ray-Vac
3A. Emptying the Debris Chamber
1.
To prevent the cleaner from losing debris, leave
the pump(s) on (filter or booster pump) and direct
the cleaner towards the edge of the pool.
2.
Grab the cleaner by the nose wheel and lift it out
of the pool (direct water coming from cleaner
toward the pool. See Fig 1).
Figure 3. Remove Debris compartment
Debris Compartment
Screen
Figure 4. Remove Debris Compartment Screen
Figure 1. Remove Ray-Vac from Pool
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 3
6.
If the pump(s) is on: put your hand over the hole
in the back of the cleaner and force the water
back into the cleaner. Use the whip hose to further
remove any debris.
SECTION 5.
Remove Ray-Vac Hose from Pool
Wall
7.
8.
If the pump(s) is off: use a garden hose to remove
debris.
5A. Quick Disconnect
1.
At the equipment pad, turn off all pool pumps.
Make sure all moving parts are free of debris.
Install the screen and debris compartment. Place
the Ray-Vac back into the pool.
2.
Grasp the Quick Disconnect Coupler and turn it
counterclockwise ¼ turn.
3.
4.
Pull out and remove hoses from pool.
To reinstall, align tabs on Quick Disconnect
Coupler in the Wall Reducer.
5.
To lock, turn the Quick Disconnect Coupler ¼
turn clockwise, then give a gentle pull on the hose
to seat the Quick Disconnect Coupler.
Figure 5. Check Debris Compartment Door
SECTION 4.
Skimmer Guard
4A. Skimmer Guard Installation
1.
Insert the Skimmer Guard into the center of the
skimmer opening about 1" from the wall edge.
Figure 7. Remove Quick Disconnect
2.
Begin turning the top half of the skimmer guard
clockwise while holding the bottom half until you
see the guard expanding in length.
3.
Continue turning until the guard expands to fit
tightly between the top and bottom of the
skimmer opening.
Skimmer
Guard
Skimmer
Opening
Figure 6. Skimmer Guard
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
Jandy Ray-Vac®
2.
Check the Jandy Energy Filter bowl. If clogged,
you must clean the filter. Use the following steps:
a. Grasp clear bowl.
SECTION 6.
Speed Adjustment After Cleaning
b. Remove the clear bowl and filter element. If
the bowl is tight, place a large screwdriver
between two of the tabs at the bottom of the
bowl. Use the shank of the screwdriver as a
lever to loosen the bowl.
c. Rinse off the filter element and replace into
bowl.
d. Tighten clear bowl by spinning the bowl into
the housing until resistance is felt. Then
tighten ¼ turn further. Hand tighten only.
Energy efficient Ray-Vac pool cleaners plumbed
with a Jandy Energy Filter and valve require adjustment
of speed after each cleaning of the main filter. If your
Ray-Vac operates with a booster pump, this adjustment
will not be necessary. If you are uncertain whether your
Ray-Vac operates with a booster pump, check with your
pool professional.
6A. Speed Adjustment
1.
At the equipment pad, turn off filtration pump.
Follow filter manufacturer's recommended
procedures for cleaning main filter. Before
cleaning main filter, be sure to turn the Jandy 3-
port valve so the line to the Ray-Vac is closed.
Turn handle until
pipe to Energy
Filter is closed
Jandy 3-Port
Valve
Turn handle until
pipe to Energy
Filter is closed
Jandy Energy Filter
Jandy
Energy
Filter
Turn Clockwise
to Loosen
Figure 9. Ray-Vac Energy Filter and Jandy Valve
If the bowl is to tight,
use screwdriver to
loosen
Figure 10. Removing Energy Filter
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 5
3.
Check the Finger Screen (at rear of Hydro-Timer)
If it is clogged, use the following steps to clear:
a. Grasp and hold the Hydro-Timer while you
unscrew the Finger Screen Case.
b. Remove the Finger Screen and rinse it off.
c. Place the Finger Screen back into its case
and tighten onto the Hydro-Timer.
5.
If the Ray-Vac sticks in an obstacle (i.e. corners,
ladders, skimmers, etc.) it is possible to increase
the pull out by changing the backup jet size.
a. Remove Jet "A" from its holder and place it
in the discharge hole "B".
b. Use a flat head screwdriver to turn the tab
under the locking tab "C".
Hydro-Timer
Hydro-Timer
A
B
Finger Screen
Case
Finger Screen
Figure 11. Cleaning Finger Screen
4.
At the pool equipment pad with the filter pump
turned on, turn the valve handle until pressure
gauge reads according to the chart for your
cleaner hose length (see Table 1).
C
Figure 12. Changing Backup Jet Size
Turn Jandy 3-Port
Valve Handle
Figure 11. Isolate Energy Filter
Length of hose
between wall
fitting and nose
of Ray-Vac
Pressure
Setting on
Gauge
21' 5"
24' 5"
27' 5"
30' 5"
33' 5"
18 psi
19 psi
20 psi
21 psi
22 psi
Table 1. Ray-Vac Pressure Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
Jandy Ray-Vac®
7.
8.
Check all hoses for wear. Carefully examine for
holes, soft spots or worn areas. Be sure to check
the Whip Hose, Silicone Pusher Hose, and
Silicone hose with Sea Anchors (see exploded
view).
SECTION 7.
Ray-Vac Maintenance
It is important to maintain the Ray-Vac as
demonstrated to insure the unit a longer life.
When adding chemicals to your pool, allow your
filtration system to circulate for at least four (4)
hours to thoroughly mix the chemicals before
operating the cleaner. Accelerated wear and
deterioration of the pool cleaner may occur if this
procedure is not followed.
7A. General Maintenance
1.
2.
3.
4.
5.
Clean main filter (see Manufacturers Owner
Manual).
Clean Energy Filter (see Section 6 "Speed
Adjustment after Cleaning").
9.
Adjust the Ray-Vac speed (see Section x "Clean
Energy Filter").
Clean Finger Screen (see Section 6 "Speed
Adjustment after Cleaning").
10. If the cleaner is out of the pool for an extended
period of time, store the hoses straight and flat or
in very large (4' diameter) loops. Do not store in
original shipping box or hang over hooks or nails
as this will cause kinks in the hose.
Clean Debris Compartment Screen (see Section 3
"Emptying the Ray-Vac Unit").
Check for wear on the following parts (see
exploded view for part numbers):
a. Nose Castor Wheel
b. Nose Wheel
c. Drive Wheels
d. Swivel Wheels
e. Venturi Bumper
f. Side Wheels
g. Wear Skids
h. Nose Bumper (Top)
i. Nose Bumper (Bottom)
6.
Check Debris Compartment Door (see Section 3
"Emptying the Ray-Vac Unit").
e
a
d
b
f
h
g
c
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 7
SECTION 8.
Troubleshooting
8A. Troubleshooting
Problem
Pool Cleaner
stalls in corner.
Cause
Solution
Corner restricting movement of
movement of Ray-Vac.
No adjustment needed. Wait until backup jet pulls
unit out of the corner.
Nose caster wheel jammed with debris. Clean or replace.
Increase backup.
See instructions under Speed Adjustment.
Pool Cleaner
stalls in skimmer.
Skimmer opening is larger than
Ray-Vac.
No adjustment needed. Wait until backup jet pulls
unit out of corner.
Add optional skimmer guard.
See instructions under Speed Adjustment.
Increase backup.
Cleaner stops
moving.
Filter system off.
Unit in backup cycle.
Dirty Finger Screen or Energy Filter.
Hole in hose.
Check time clock.
Normal operation.
Clean Finger Screen or Energy Filter.
Replace defective hose.
Backup Hydro-Timer releasing most
of the water out of the discharge hole.
Transporter jet plugged.
Replace defective backup jet gear assembly.
Clean or replace the transporter jet.
Cleaner moves
very slowly.
Debris chamber full.
Clean chamber.
Clean as necessary.
Finger Screen, Energy Filter, main
filter, or filter pump strainer is dirty.
Insufficient speed.
Increase speed by increasing pressure to cleaner.
Replace defective hose.
Hose in hose.
Water in head float.
Replace defective head float.
Pressure gauge has failed false reading. Replace pressure gauge
Hose tangles.
Debris chamber full.
Cleaner moves to slowly.
Feed hose too long.
Frozen swivels.
Bent or irregular hose.
Water in head float.
Floatation incorrect.
Clean chamber.
Speed up cleaner by increasing pressure to cleaner.
Recheck hose length.
Check and/or replace swivels.
Straighten or replace hose.
Replace defective head float.
See "Hose Length adjustment" section.
Dirt accumulates
near main drain.
Insufficient suction on the main drain. Reset suction so at least 50% of the circulation water
is sucked from the main drain.
Cleaner in not operating long enough. Increase running time of the cleaner by adjusting
time clock to operate longer.
Finger Screen is
often found dirty.
Energy Filter element is damaged.
Debris is passing by main filter.
Valve to Ray-Vac was not closed.
Check Energy Filter element and replace if necessary
Main filter element damaged. Replace as necessary.
Close valve to Ray-Vac before cleaning the main
Cleaner beaches on
top step.
Insufficient water above top step.
Cleaner need a minimum of 5" of water to operate
properly.
Cleaner stops on
main drain.
Too much suction through main filter. Reset suction on main drain.
Cleaner tangles in
ladder.
Ladder/skimmer guard not installed.
Install optional ladder/skimmer guard.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 8
Jandy Ray-Vac®
SECTION 9.
Exploded View and Part Numbers
9A. Ray-Vac and Ray-Vac/DM Hose Parts
List and Exploded View
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 9
Dwg # Old Part# 2002 Part#
Description
1
3782
3783
1138
3784
1098
1099
2030
1121
1115
1116
1117
1119
2015
1453
1139
1814
2985
2818
4296
1325
2300
2822
2029
1140
1141
1162
1161
3154
3183
1177
3587
2931
1120
3272
3222
3223
3224
2524
2523
1133
3781
3225
2887
2870
2612
3391
3293
3191
1154
2888
3786
4047
4060
3981
2930
4143
4267
5532
1178
1433
3266
7072
7073
2777
R0376300
R0376300
R0376300
R0376300
R0372800
R0372800
R0373000
R0374100
R0377300
R0377300
R0374100
R0374100
R0374300
R0377100
R0376400
R0377200
R0375700
R0373600
R0376500
R0376500
R0376500
R0377000
R0373000
R0373000
R0373000
R0373000
R0373000
R0373400
R0373400
R0373400
R0374900
R0373200
R0374300
R0374300
R0377300
R0374100
R0374100
R0376500
R0374200
R0376500
R0376500
R0373400
Quick Disconnect Wall Fitting 1 ½"† See #5532
Quick Disconnect Wall Fitting ¾"† See #5532
Garden Hose Washer
2
3
4
5
6
7
8
9
Quick Disconnect Coupler † See #5532
Filter Screen Case
Filter Screen
Hydro-timer Swivel, Ball Bearing
Mender Sleeve Retaining Clip † See #3222,3223,3224,4143,3449
Mender Sleeve 5/8" Vinyl † See #3222,3272
Mender Sleeve Ferrule 5/8" Vinyl † See #3222,3272
Mender Sleeve ½" Vinyl † See #3223
Mender Sleeve ½" Silicone † See #3224
Hose Vinyl 5/8" w/2 Floats
Hose Vinyl ½" w/Sea Anchor
Sea Anchor † See #4267
Hose Silicone ½" x 2' w/Sea Anchor/Float/Wear Ring
Hose Silicone ½" x 12" w/2 Wear Rings/Float
Pusher Hose Silicone 3/8" x 12"
Hydro-timer Replacement Kit
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Screw #8 x 5/8"/Ht Case
O-ring, Cover For Hydro-timer
Hydro-timer Gear Assembly
Line Swivel, Ball Bearing Complete
Hose Coupler
Line Jet
Line Whip “Y” Jet
Pusher Jet
Whip 6' Blue Complete w/8 Wear Rings/Sleeve/Jet
Whip 3' w/3 Wear Rings
Whip 3' Blue w/Wear Rings/Jet/Sleeve
Head Replacement White(Black R0375000,Dessert Model R0376800,Vinyl R0376000)
Speed Adjustment Kit*
Line Float
Hose Vinyl 5/8" Extension Kit *
Mender Sleeve Kit 5/8" Vinyl*
Mender Sleeve Kit ½" Vinyl*
Mender Sleeve Kit ½" Silicone*
Hydro-timer Jet .25
Hydro-timer Jet .20
Hydro-timer Case Top
Hydro-timer Case Bottom † See #3981
Whip Jet Kit*
Jandy Filter w/Gauge & Valve
Pressure Gauge 0-60 P.S.I. 1/8"
Jandy Filter Top w/Adapter
Jandy Filter Element Poly Pro
Jandy Filter O-ring Replacement Kit*
Jandy Filter Bowl w/O-ring
Valve 3-Port CPVC 1 ½"
Jandy Filter w/Gauge
Fitting ¾" Fgh To Vinyl Hose
Swivel Rebuild Kit*
Quick Disconnect Kit*
Hydro-timer Case Bottom Kit*
Booster Pump Kit*
Mender Sleeve Retaining Clip Kit (6 Pack)*
Sea Anchor Kit*
Quick Disconnect Coupler Kit
Barbed Joiner
Barb Joiner Sleeve
Corner Kit*
Back Hose Tune Up Kit
Front Hose Tune Up Kit (Includes Gear Assembly)
R0373200
R0374000
R0374600
R0374500
R0373500
R0372800
R0373000
R0376500
R0376500
R0373200
R0374100
R0376400
R0376300
R0373400
R0373400
R0374200
R0375400
R0375400
R0376900
Transporter Jet
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 10
Jandy Ray-Vac®
9B. Ray-Vac and Ray-Vac/DM Gunite Head
Parts List and Exploded View
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 11
Dwg # OldPart # 2002 Part #
Description
1
3589
3518
6938
3590
2772
3671
3555
3539
2800
2797
2796
3215
2798
3506
2746
2794
3514
3512
3513
2776
1092
2990
1409
2808
2809
2806
2810
3521
2841
3363
3293
2799
2814
2840
3533
2915
2914
2916
3276
3016
2936
2999
3615
3218
3613
3611
3723
3617
3270
3269
3619
3509
3510
2777
4618
4107
4632
4301
2138
R0374900
R0374700
R0375200
R0375100
R0373600
R0375100
R0373700
R0375100
R0375800
R0373700
R0373700
R0373700
R0375100
R0375100
R0373700
R0373700
R0375500
R0375500
R0375500
R0373600
R0373600
Top Complete White* (Black R0375000)
Screen Frame Complete FM White (Black R0375300)
Screen Desert Model (Extra)
Bottom Complete
2
2a
3
4
5
6
7
8
9
NOTE:
Float
Door Complete*
† Not Sold Separately.
Included In The Part #
Indicated.
* Bagged Parts Kits See
pgs. 122-125.
Swivel Wheel Complete (Small) & See 3723
Door Spring White (Black R0376600)
Wear Skid
Drive Wheel Hub Cap & See #3215
Drive Wheel & See #3215
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37a
37b
38
39a
39b
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Drive Wheel Kit*
Drive Wheel ShaftWhite (Black R0376600)
Drive Wheel Bushing Clip White (Black R0376600)
E-ring & See #3589, 3590, 3615,3619, 3723, 4142
Swivel Wheel Housing Cover & See #3723
Venturi Bumper & See #3611
Nose Bumper Top & See #3611
Nose Bumper Bottom & See #3611,3619
Transporter Jet Sleeve & See #3270
Screw #6 x ¼" Triple-dual Holding
Screw #6 x 5/8" & See #3269, 3270, 4131, 4590
Screw #6 x ½" Type 25
Side Wheel & See #3618, 3269
Side Wheel Axle & See 3618, 3269
Nose Wheel Axle & See 3613, 3269
Transporter Jet Wear Button & See #3269,3270
Nose Wheel & See 3613
R0374900
R0374900
R0373700
R0373600
R0373700
R0373700
R0375800
R0374500
R0375800
R0375800
R0375800
R0375800
R0373100
R0373100
R0373100
R0374400
R0375800
R0373300
R0373300
R0375800
R0373700
R0373700
R0375500
R0373700
R0373700
R0373600
R0374900
R0375800
R0373700
R0373700
R0376900
R0373700
R0375500
R0375500
R0375500
R0373600
Nose Wheel Axle Bushing & See #3613
Nose Caster Wheel Complete & See #3615
Jandy Filter O-ring Replacement Kit
Latch & See #3016
Latch O-ring 008 & See #3016
Latch Washer & See #3016
Nose Weight & See #3619
Ladder Guard Side Axle & See #2916
Ladder Guard Nose Axle & See #2916, 3276
Ladder Guard Kit White
Ladder Guard Kit (Tall)
Bottom Latch Kit*
Skimmer Guard Kit Standard
Skimmer Guard Kit Tall
Nose Caster Wheel Kit*
Side Wheel Kit*
Nose Wheel Kit*
Bumper Kit*
Swivel Wheel Kit*
Drive Wheel Clip Kit* Gunite (R0373800 Vinyl)
Transporter Jet Sleeve Kit*
Wear Button Kit*
Nose Plate Kit*
Nose Caster Wheel Insert Bushing Top & See #’s 3615, 3616, 3619, 4590, 4618
Nose Caster Wheel Insert Bushing Bottom & See #’s 3615, 3619, 4618
Transporter Jet Complete
Nose Caster Wheel Bushing Kit*
Flat Mouth White & See Kit # 4632*
Flat Mouth Kit*
Screw #4 x 5/16" Phil Pn Ss (Black R0375600)
Screw 8.32 x ¾
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 12
Jandy Ray-Vac®
9C. Ray-Vac and Ray-Vac/DM Vinyl/
Fiberglass Head Parts List and
Exploded Views
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Pik Technologies, Inc.
Page 13
Dwg # OldPart # New Part #
1
Description
Top Complete V/F*
3646
4039
3518
3645
2772
3671
2795
3539
2800
3627
3293
3725
3638
3506
2746
2794
3514
3512
3513
2776
1092
2990
1409
2808
2809
2806
2810
3628
2841
3639
1467
2799
2814
2840
3533
2915
2914
2916
3276
3016
2936
2999
3727
3726
3218
3611
3220
3617
3270
3269
4136
3509
R0376000
R0376100
R0374700
R0375900
R0373600
R0375100
R0373800
R0375100
R0375800
R0373800
R0374500
R0375900
R0375900
R0375100
R0373700
R0373700
R0375500
R0375500
R0375500
R0373600
R0373600
2
2a
3
4
5
6
7
8
9
Screen Frame Complete Coarse
Screen Frame Complete Fm
Bottom Complete V/F
Float
Door Complete *
Swivel Wheel Complete (Small) & See #3220, 3645
Door Spring
Wear Skid
NOTE:
† Not Sold Separately.
Included In The Part #
Indicated.
* Bagged Parts Kits See
pgs. 122-125.
Drive Wheel Hub Cap & See #3645, 3725
Jandy Filter O-ring Replacement Kit *
Drive Wheel Housing Kit V/F *
Drive Wheel Shaft V/F
Drive Wheel Bushing Clip & See #3617
E-ring & See #3589, 3590, 3615, 3619, 3723, 4142
Swivel Wheel Housing Cover & See #3220
Venturi Bumper & See #3611
Nose Bumper Top & See #3611
Nose Bumper Bottom & See #3611,4136
Transporter Jet Sleeve & See #3270
Screw #6 x ¼" Triple-dual Holding
Screw #6 x 5/8" & See #3269, 3270, 4131, 4590
Screw #6 x ½" Type 25
Side Wheel & See #3618, 3269
Side Wheel Axle & See 3618, 3269
Nose Wheel Axle & See 3613, 3269
Transporter Jet Wear Button & See #3269,3270
Nose Wheel & See 3726
Nose Wheel Axle Bushing & See #3613
Nose Caster Wheel V/F & See #3725,3727
Screw #6 x ½" Phil Pn “A” Ht
Latch & See #3016
Latch O-ring 008 & See #3016
Latch Washer & See #3016
Nose Weight & See #3619
Ladder Guard Side Axle & See #2916
Ladder Guard Nose Axle & See #2916, 3276
Ladder Guard Kit White
Ladder Guard Kit (Tall)
Bottom Latch Kit *
Skimmer Guard Kit Standard
Skimmer Guard Kit Tall
Caster Wheel Kit V/F *
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37a
37b
38
39a
39b
40
41
42
43
44
45
46
47
48
49
4618
50
51
52
53
54
55
56
57
58
R0374900
R0374900
R0373700
R0373600
R0373800
R0373700
R0376200
R0377000
R0375800
R0375800
R0375800
R0375800
R0373100
R0373100
R0373100
R0374400
R0375800
R0373300
R0373300
R0376200
R0373800
R0373700
R0375500
R0373800
R0373700
R0373600
R0374900
R0376200
R0373700
Nose Wheel Kit V/F *
Side Wheel Kit*
Bumper Kit *
Swivel Wheel Kit V/F*
Drive Wheel Clip Kit*
Transporter Jet Sleeve Kit *
Wear Button Kit *
Nose Plate Kit White V/F*
Nose Caster Wheel Insert Bushing Top & See #’s 3615, 3616, 3619, 4590,
3510
2777
4136
3629
3630
3640
3642
2138
4618
R0373700
R0376900
R0376200
R0373800
R0373800
R0373800
R0373800
R0373600
R0373700
Nose Caster Wheel Insert Bushing Bottom & See #’s 3615, 3619, 4618
Transporter Jet Complete
Nose Plate Kit (White) V/F
Side Wheel V/F & See #’s 3645, 3725
Caster Wheel Housing V/F & See #’s 3645,3725
Caster Wheel Cover V/F & See #’s 3645, 3725
Swivel Wheel Washer V/F & See #’s 3220,3645
Screw 8.32 x ¾"
Nose Caster Wheel Bushing Kit *
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
These warranties extend only to the first retail purchaser of Laars and Jandy products that have not been moved
from their original installation sites. Laars and Jandy warrants all parts to be free from manufacturing defects in
material and workmanship as detailed below for the designated time frame, commencing from the date of installa-
tion. If any parts are found to have manufacturing defects, Laars and Jandy will provide replacement of such defec-
tive parts.
1 year
2 years
3 years
5 years
Lifetime
Cleaners:
Ray-Vac®
Others
X
X
Control Systems:
AquaLink® RS and Accessories
AquaLink® RS (w/Surge Protection)
AquaSwitch®, Pool Control, Ji,
X
X
X($50 Deductable)
X($75 Deductable)
and Solar Control
X
X
Filters:
Tank
Heaters:
Lite2
Controls, Firebox Panels,
Heat Exchanger, Burners
Controls, Firebox Panels,
Heat Exchanger,
All Other Parts
All Other Parts
LX, Hi-E2
Fan Motor, Burners
Hot Shot
X
Oil-Fired, XL-2, XL-3
Oil Burner, Controls
Heat Exchanger,
Firebox
All Other Parts
Pumps:
Jandy Valve Actuator:
X
X
Motor (from Manufacturer)
Valves:
NeverLube®
Others
X
X
X
Water Features:
EXCLUSIONS:
The liability of Laars and Jandy shall not exceed the repair or replacement of defective parts and does not include any costs for labor to remove and reinstall the
defective part, transportation to or from the factory, and any other materials required to make the repair.
This warranty does not cover failures or malfunctions resulting from the following:
1. Failure to properly install, operate or maintain the product(s) in accordance with our published Installation, Operation and Maintenance
Manuals provided with the product(s);
2. The workmanship of any installer of the product(s);
3. Not maintaining a proper chemical balance [pH level between 7.2 and 7.8, Total Alkalinity (TA) between 80 to 120 ppm, Total Dissolved Solids (TDS)
less than 2000];
4. Abuse, alteration, accident, fire, flood, lightning, rodents, insects, negligence or acts of God;
5. Scaling, freezing, or other conditions causing inadequate water circulation;
6. Operating the product(s) at water flow rates outside the published minimum and maximum specifications;
7. Use of non-factory authorized parts or accessories in conjunction with the product(s);
8. Chemical contamination of combustion air or improper use of sanitizing chemicals such as, introducing sanitizing chemicals upstream of the heater and
cleaner hose or through the skimmer;
9. Overheating, incorrect wire runs, improper electrical supply, collateral damage caused by failure of O-Rings, DE grids, or cartridge elements, damage
caused by running the pump with insufficient water;
10. The installation of a surge protection kit does not extend the warranty of the original product(s).
LIMITATION OF LIABILITY:
This is the only warranty given by Laars and Jandy. No one is authorized to make any other warranties on Laars and Jandy behalf. THIS WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND MERCHANTABILITY. LAARS AND JANDY EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL, INCIDEN-
TAL, INDIRECT OR PUNITIVE DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state or by province.
WARRANTY CLAIMS:
For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number and date of
installation. The installer will notify the factory for instructions regarding the claim and for the location of the nearest Laars and Jandy designated service center. If the
dealer is not available, you can locate a service center in your area by visiting www.jandy.com or you can call the Technical Support Department at (707) 776-8200
ext. 260 for assistance. All returned parts must have a Returned Material Authorization number in order to be considered for warranty evaluation. If there are any
questions about the coverage of this warranty, please contact Laars and Jandy at the address below.
*
*6000 Condor Drive, Moorpark, CA, USA 93021 • 707.776.8200 FAX 707.763.7785
480 S. Service Road West, Oakville, Ontario, Canada L6K 2H4 • 905.844.8233 FAX 905.844.2635
Litho in U.S.A. © Water Pik Technologies, Inc. 0202
For Technical Support call 707-776-8200, ext. 260
Download from Www.Somanuals.com. All Manuals Search And Download.
|