FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ꢀ Reorient or relocate the receiving antenna.
ꢀ Increase the separation between the equipment and receiver.
ꢀ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ꢀ Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the
equipment.
EN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power OFF and remove the
batteries and the AC power adapter.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
If the camera has fallen or its case has been damaged, turn the power OFF and remove the
batteries and the AC power adapter.
Continued use in this state might cause fire or electric shock. Consult the store of purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask the store of
purchase.
Use the AC adapter (Optional Accessory) only with the indicated power supply voltage.
Use with any other power supply voltage might cause fire or electric shock.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow, on the beach, or
near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing injury.
Keep the batteries out of the reach of children.
Swallowing batteries might cause poisoning. If the battery is accidentally swallowed, immediately
consult a physician.
Do not use the camera while you are walking, driving or riding a motorcycle.
This might cause you to fall over or result in traffic accident.
EN-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions
Insert the batteries paying careful attention to the polarity (+ or –) of the terminals.
Inserting the batteries with its polarities inverted might cause fire and injury, or damage to the
surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to leak. If the internal fluid
enters your eyes or comes into contact with your body or clothes, rinse with fresh water. If the
internal fluid has entered your eyes, consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use excessive force when
handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous use.
The battery becomes hot during use. Touching a hot battery might cause burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use the camera in a
well-ventilated place.
Do not leave the camera in places where the temperature may rise significantly, such as
inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and electric shock.
WARNING: Handling the USB on this product may expose you to lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. Wash hands after handling.
EN-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Battery Usage
ꢀ Do not use batteries other than those specified for use with your ViviCam 8400. Use of unsuitable
batteries may result in the batteries splitting, or leaking and may cause a fire, injury, or soiling of the
battery compartment.
ꢀ When placing the batteries into the ViviCam 8400, check the polarity markings on the batteries (- and
+) to ensure that the batteries are inserted correctly. Incorrect battery polarity will result in ViviCam
inoperability and may result in the batteries splitting or leaking and causing a fire, injury, or soiling of
the battery compartment.
ꢀ Remove the batteries if the ViviCam 8400 will not be used for an extended period of time. The
batteries may leak and cause a fire, injury or soiling of the battery compartment. If the batteries leak,
clean and wipe the battery compartment carefully and install new batteries. Wash your hands carefully
if you touch the battery fluid.
When using batteries, carefully read and strictly observe the Safety Instructions and the notes
described below:
ꢀ Ni-MH rechargeable batteries are highly recommended. To maximize performance and lifetime, we
recommend that you fully charge the batteries and discharge them for at least one complete cycle
before use.
ꢀ Avoid using batteries in extremely cold environments as low temperatures can shorten the battery life
and reduce ViviCam 8400’s performance. Low temperature will adversely affect alkaline battery
performance.
ꢀ Using new rechargeable batteries or rechargeable batteries that have not been used for an extended
period of time will affect the number of images that can be captured.
ꢀ If you will not be using the batteries for an extended period of time, remove them from the ViviCam
8400 to prevent leakage or corrosion.
ꢀ Never use batteries of different types (together) or mix old and new batteries. Never use manganese
batteries.
ꢀ More information about batteries is provided in this manual in subsequent sections.
EN-5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
INTRODUCTION ................................................ 8
PHOTOGRAPHY MODE................................... 23
Shooting Images - The Basics..........................23
Setting Image Resolution and Quality ................ 24
Using the Zoom Function................................... 25
Setting Focus..................................................26
Using the Flash............................................... 27
Using the Self-Timer......................................... 28
Adjusting the Exposure (EV Compensation) /
Package Contents............................................ 9
GETTING TO KNOW YOUR VIVICAM 8400....... 10
Front View...................................................... 10
Rear View......................................................... 11
Mode Dial ...................................................... 12
LCD Monitor Information..................................... 13
Backlight Correction.......................................... 29
Setting White Balance...................................... 30
PREPARING YOUR VIVICAM 8400................... 15
Installing the Batteries .................................... 15
Using the AC Power Adapter
USING THE MODE DIAL.................................... 31
[A] Auto Mode..................................................31
[P] Program Mode ............................................ 31
[Tv] Shutter Speed Priority Photography Mode......32
[Av] Aperture Priority Mode............................... 32
[M] Manual Mode..............................................33
[SCENE] Scene Mode....................................... 33
(Optional Accessory)..........................................16
Inserting and Removing an SD Memory Card
(Optional Accessory) ........................................17
Attaching the Camera Strap.............................. 18
LED Indicators..................................................18
GETTING STARTED........................................... 19
Turning the Power On/Off ................................. 19
Choosing the Screen Language......................... 19
Setting the Date and Time ................................20
Formatting an SD Memory Card or Internal
Memory............................................................ 21
Using the LCD Monitor....................................... 22
ADVANCED SHOOTING................................... 34
Burst.............................................................. 34
Auto Exposure Bracketing (AEB) ...................... 35
Selecting the Metering Mode ............................. 36
EN-6
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE - THE BASICS..................... 37
Viewing Images ............................................... 37
Magnifying Images .......................................... 38
Thumbnail Display .......................................... 39
Slideshow Display ........................................... 40
Resizing an Image ........................................... 41
EDITING SOFTWARE INSTALLATION..............55
Installing Photo Explorer....................................55
Installing Photo Express....................................56
INSTALLING ADOBE ACROBAT READER..............57
USER MANUAL...................................................58
VIDEO MODE.................................................... 42
Recording Video Clips ...................................... 42
Playing Back Video Clips ................................. 43
MENU OPTIONS...............................................59
Camera Menu.................................................... 59
Video Menu ................................................... 63
Playback Menu............................................... 64
Setup Menu.................................................... 66
PLAYBACK MODE – ADVANCED FEATURES...44
Playing Back Still Images/Video Clips on TV ........ 44
Deleting Images/Video Clips.............................. 45
Protecting Images/Video Clips ........................... 46
Connecting to a PictBridge Compliant Printer.........47
CONNECTING THE VIVICAM 8400 TO
OTHER DEVICES............................................. 68
VIVICAM 8400 SPECIFICATIONS....................... 69
APPENDIX........................................................ 70
TRANSFERRING FILES FROM VIVICAM 8400 TO
COMPUTER......................................................51
Step 1: Install the USB driver .........................52
Step 2: Connect the ViviCam 8400 to your
computer...........................................53
Step 3: Download images or video clips............54
EN-7
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing the new ViviCam 8400!
Equipped with a 8.0 Megapixels CCD sensor, your ViviCam 8400 delivers quality, 3264 x 2448 resolution
images. Other features provided by the ViviCam 8400 include the following:
„ 8.0 Megapixels
„ USB connection (USB 2.0 compliant)
Still images, video clips, or voice recording files
that you have recorded can be downloaded to
your computer using the USB cable (A USB
A high-resolution CCD sensor provides 8.0
megapixels for excellent image quality.
„ Auto flash
An auto flash sensor automatically detects
the shooting (lighting) conditions and
determines whether the flash should be used.
„ 2.0” LTPS color image LCD monitor
driver is required for Win 98 and Win98SE).
„ PictBridge support
You can connect the ViviCam 8400 directly to
a printer that supports PictBridge and perform
image selection and printing using the ViviCam
8400 monitor screen and controls.
„
Optical zoom : 1x~3x
„ Digital zoom: 1x~4x
„ Provided editing software: Photo Explorer /
Photo Express
„ 32MB internal (built-in) memory
Images can be captured without using a
memory card.
You can enhance and retouch your images on
your computer by using the provided editing
software.
„ Support for SD memory card for memory
expansion
You may wish to expand the memory capacity
(up to 1GB) by using an external memory
card.
EN-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
Carefully unpack your kit box and ensure that you have the following items. In the event that any item is
missing or if you find any mismatch or damage, promptly contact your dealer.
Common Product Components:
ꢀ ViviCam 8400 Digital Camera
ꢀ User’s Manual
ꢀ USB Cable
ꢀ
ꢀ
ꢀ
AV Cable
Camera Strap
Camera Pouch
ꢀ Software CD-ROM
Common (Optional) Accessories:
ꢀ SD memory card
ꢀ AC power adapter
ꢀ Batteries
ꢀ The product and accessories that come with your ViviCam 8400 may be different from those described in this
manual. This is due to the fact that different retailers often specify slightly different product inclusions and
accessories to suit their market requirements, customer demographics, and geographical preferences. Products
vary between retailers especially with accessories such as batteries, chargers, memory cards, cables, carrying
cases/pouches, and language support. Occasionally a retailer will specify a unique product color, appearance,
and internal memory capacity. Contact your dealer for precise product definition and included accessories.
EN-9
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING TO KNOW YOUR VIVICAM 8400
Front View
5
6
1
7
8
2
3
4
9
10
1. Shutter button
2. Flash
6. Mode dial
7. Viewfinder window
8. Self-timer LED
3. Microphone
4. Lens
9. PC (USB) / AV Out terminal
10. DC in 3V terminal
5. Power button
EN-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear View
1
2
3
4
5
6
7
8
9
10
11
12
13
16
15
14
9.
X
Arrow button (Right)
Self-timer button
Arrow button (Down)
Exposure compensation button
Delete button
1. Viewfinder
2. Diopter adjustment dial
3. Viewfinder LED
10.
11.
T
4.
/
Zoom in (telephoto) button
/
Zoom out (wide-angle) button
/ Thumbnail button
Display button
12.
13.
OK button
5.
Playback button
6. Strap holder
Menu button
14. Battery / SD card cover
15. Tripod socket
7. S
Arrow button (Up)
/
Focus button
16. LCD monitor
8. W
Arrow button (Left)
Flash button
EN-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode Dial
You can select from seven modes and setup mode according to conditions to achieve the desired effect.
9
1
2
8
3
4
7
6
5
Mode
Description
1.
2.
Power button
Program
Press to turn on/off the power.
P
A
Select this mode to permit the shutter speed and aperture
to be set automatically.
3.
4.
5.
6.
Auto
Select this mode to adjust point-and-shoot action.
Select this mode to record video clips.
Select this mode to adjust VIVICAM 8400 settings.
Select this mode to permit full manual control over exposure,
aperture and other settings.
Video
Setup
Manual
M
7.
8.
9.
Av
Tv
Aperture priority
Select this mode to specify the aperture value while the ViviCam 8400
sets the corresponding shutter speed.
Shutter speed priority Select this mode to specify the shutter speed while the ViviCam 8400
sets the corresponding aperture.
SCENE SCENE
Point-and-shoot simplicity when taking pictures under 4 special
conditions.
EN-12
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Monitor Information
1
2
3
4
5
6
ꢀ Camera Mode
SD
P
8
7
8
14
13
12
9
X1
1. Mode indication
[ P ] Program Mode
[ A ] Auto Mode
1.6x
2004.09.17
[
[
]
]
Tungsten
11
10
Fluorescent
[
] Video Mode
[ M ] Manual Mode
[ Av ] Aperture priority Mode
[ Tv ] Shutter speed priority
[SCENE]SCENE Mode
2. Image quality
9. Capture mode indicator
[
[
] Status of internal memory
] Status of SD memory card
[
[
[
]
]
]
Single
Burst
AEB
X1
SD
6. Remaining battery status
[
[
[
[
] Full battery power
] Medium battery power
] Low battery power
] No battery power
10. Date
11. Zoom status
12. Focus area
13. Focus indicator
(no indication for auto focus)
[
[
[
] Fine
] Normal
] Economy
7. Self-timer mode
3. Image size
[
[
[
[
]
]
]
]
OFF
[
[
]
]
Macro
Infinity
[
[
[
[
]
]
]
]
3264 x 2448
2272 x 1704
1600 x 1200
640 x 480
2 sec. delay
10 sec. delay
10+2 sec. delay
[ AF ] Auto focus
14. Flash mode
10+2
8. White balance
Auto
[
[
[
[
] Auto Flash (Default)
] Red Eye
] Forced flash
] No Flash
4. Possible number of shots
5. Internal memory/SD memory
card indicator
[
[
]
]
Daylight
Cloudy
EN-13
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ Video Mode
3
4
2
1
SD
1. Video mode
00:33
2. Recordable movie time available
3. SD memory card indicator (if present)
4. Battery power indicator
5. Focus area
5
2
3
ꢀ Image Playback
SD
1
4
1. Playback mode
100-0001
SIZE
2. SD memory card indicator (if present)
3. Battery power indicator
4. Playback information
1600X1200
+1.5
EV.
05:22
01. 04. ’04
1
3
4
2
ꢀ Video Playback
SD
1
5
1. Playback mode
2. Video mode
3. SD memory card indicator (if present)
4. Battery power indicator
5. Playback indicator
100-0001
SIZE
640X480
+1.5
6
EV.
05:22
01. 04. ’04
6. Playback information
1
EN-14
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARING THE VIVICAM 8400
Installing the Batteries
You can use 2 AA size batteries to power the ViviCam 8400. Make sure that the power of the ViviCam 8400
is off before inserting or removing the batteries.
1. Make sure the ViviCam 8400 is turned off.
2. Open the battery cover.
3. Insert the batteries in the correct orientation as shown in the
illustration.
4. Close the battery cover.
„
To remove the batteries, turn the Vivicam 8400 off and hold
the camera with the battery compartment facing upward.
Then open the battery cover.
„ Be careful not to drop the batteries when opening or closing the battery cover.
„ While alkaline batteries offer limited use, Ni-MH rechargeable type AA batteries are strongly recommended for
performance and economy.
EN-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the AC Power Adapter (Optional Accessory)
Use of the AC power adapter is recommended if you intend to use the LCD monitor for a long time or
connect the ViviCam 8400 to a PC.
1. Make sure your ViviCam 8400 is turned off.
2. Connect one end of the AC power adapter to the
camera jack labeled "DC IN 3.0V".
3. Connect the other end to an electrical outlet.
ꢀ Make sure to use only the AC power adapter specified for the ViviCam 8400. Damage caused by the use of an
incorrect adapter is not covered under the warranty.
ꢀ To prevent unexpected auto power off resulting from no battery power left during the process of transferring your
images to the computer, use the AC power adapter as a power supply or a freshly-charged pair of Ni-MH batteries.
ꢀ The AC power adapter can only be used to power the ViviCam 8400. Batteries cannot be charged inside the
ViviCam 8400.
EN-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting and Removing an SD Memory Card (Optional Accessory)
The ViviCam 8400 comes with 32MB of internal memory, allowing you to store captured still images or
video clips in the ViviCam 8400. You can also expand the memory capacity by using an optional SD
(Secure Digital) memory card so that you can store more files.
1. Make sure your ViviCam 8400 is turned off before inserting or
removing a memory card.
2. Open the SD memory card cover.
3. Insert an SD memory card in the correct orientation as shown in
the illustration and press downward until it clicks into place.
4. Close the battery/SD memory card cover.
„
To remove the SD memory card, make sure the ViviCam
8400 is turned off. Press lightly on the edge of the memory
card and it will eject.
„ Be sure to format an SD memory card with this ViviCam 8400 before using
it. Refer to section in the manual titled “Formatting an SD Memory Card
or Internal Memory” for further details.
„ To prevent valuable data from being accidentally erased from an SD card,
you can slide the write protect tab (on the side of the SD memory card)
to “LOCK”.
„ To save, edit, or erase data on an SD memory card, you must unlock the card.
„ The ViviCam 8400, like most digital cameras will automatically use a
memory card if it is inserted into the memory card slot. This is called
“card preference”. Data stored in internal memory will not be accessible
if a memory card is present. To again access your data stored in internal
memory, simply remove the SD card.
EN-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Camera Strap
Attach the strap as shown in the illustration.
1
2
LED Indicators
Indicator
State
Description/Activity
LED indicator
Solid red
Solid green
Solid green
Blinking red
The ViviCam 8400 is powering up.
The ViviCam 8400 is ready to record images (or movies).
USB communication/transfer in progress
Charging the flash.
LED indicator
LED indicator
Self-timer indicator
Blinking green The self-timer function is activated.
EN-18
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Turning the Power On/Off
ꢀ Press the
button until the ViviCam 8400 turns on.
ꢀ To turn the power off, press the
button again.
Choosing the Screen Language
Follow the steps below to choose the desired language.
Set-up2
Format
Set-up3
Set-up1
1. Rotate the mode dial to
pressing the button.
The [Set-up1] menu is displayed.
2. Use T to select [Language], then press the
3. Use S or T to select the language you want.
and turn your ViviCam 8400 on by
Beeper
Louder
m/d/y
ꢀ
Date & Time
button.
Y/M/D
Language
English
Set :
4 / 4
4. Press the
button to confirm.
Language
English
Set :
1 / 7
EN-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
Follow the steps below to set the date display style, current date and time.
1. Rotate the mode dial to
pressing the button.
The [Set-up1] menu is displayed.
2. Use T to select [Date & Time], then press the
You may press W or X to switch the date types.
and turn your ViviCam 8400 on by
Set-up2
Format
Set-up3
Set-up1
„
Louder
Beeper
button.
„
m/d/y
Date & Time
Y/M/D
3. Press the W / X buttons to select Year, Month, Day and Time
Language
English
fields.
Set :
3 / 4
„
„
„
To increase a value, press the S button.
To decrease a value, press the T button.
The time is displayed in 24-hour format.
Date & Time
4. Press the
button after all fields are set.
/
10
:
/
2005
10
00
00
Select
:
Set :
EN-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Formatting an SD Memory Card or Internal Memory
The term “Formatting” means preparing an “SD Memory Card” to record images; this process is also called
“initialization”. This utility formats the internal memory (or memory card) and erases all stored images and
data.
1. Rotate the mode dial to
pressing the button.
The [Set-up1] menu is displayed.
and turn your ViviCam 8400 on by
Set-up2
Format
Set-up3
Set-up1
ꢀ
Louder
Beeper
2. Use T to select [Format], then press the
3. Use S or T to select [Yes], then press the
button.
button to confirm.
Date & Time
m/d/y
Y/M/D
Language
English
Set :
1 / 4
Format
Yes
No
Set :
ꢀ When you format an SD memory card, be aware that all data of which will be permanently erased. Protected
images are also erased.
ꢀ To format the internal memory, do not insert a memory card into the ViviCam 8400. Otherwise, you will format the
memory card.
ꢀ Formatting is an irreversible action and data cannot be recovered at a later time.
ꢀ An SD memory card having any problem cannot be properly formatted.
ꢀ If your SD card cannot be formatted, you should use a different card.
EN-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the LCD Monitor
Your ViviCam 8400 is equipped with a 2.0" full color TFT LCD monitor to help you compose images,
replay recorded images/video clips or adjust menu settings. The mode icons, text and numbers displayed
on the monitor may vary according to the current settings.
1. Rotate the mode dial to A , P , SCENE , Tv , Av , M or
2. Press the button to turn on the power.
.
/
3. Compose your scene on the LCD monitor.
4. Press the shutter button.
ꢀ The LCD monitor darkens in strong sunlight or bright light. This is not a malfunction.
ꢀ To prevent your images from being blurred while pressing the shutter button, always hold it carefully. This is
especially important when you are shooting under low lighting conditions, when your ViviCam 8400 will select a
slower shutter speed to ensure that your images are properly exposed.
EN-22
Download from Www.Somanuals.com. All Manuals Search And Download.
PHOTOGRAPHY MODE
Shooting Images - The Basics
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M and turn
SD
8
A
your ViviCam 8400 on by pressing the
button.
2. Compose the image on the monitor screen so that the main
subject is within the focus frame.
3. Press the shutter button down half way to focus the image.
X1
ꢀ
When you press the shutter button down half way, the
ViviCam 8400’s Auto Focus feature automatically focuses
the image and determines the exposure.
1.6x
2004.09.17
4. Press the shutter button the rest of the way down to capture the
image.
ꢀ The actual image will appear to be larger after being captured than it initially looked on the LCD.
ꢀ Pressing the button switches the LCD monitor display mode. Each time you press the
/
/
button, the
display changes in the following order: Focus Frame On ꢁ Indicators Off ꢁ Composition Line On ꢁ LCD Off.
EN-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Image Resolution and Quality
As you get to know the ViviCam 8400, you can set the image resolution (number of vertical and
horizontal pixels) and image quality (compression ratio) based on the types of images you want to shoot.
These settings affect the number of images that can be stored in memory, or on a memory card.
Higher resolution and higher quality images provide finer detail but cause the images’ file size to be larger.
To change image resolution or image quality, perform these steps below:
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M and turn
Image Size
your ViviCam 8400 on by pressing the
2. Press the button, then use W or X to select the [Mode1] /
[Mode2] / [Mode3] menu.
In A (Auto) Mode, press
button.
3264 x 2448
2272 X 1704
1600 X 1200
640 X 480
ꢀ
to access in menu directly.
3. Use T to select [Image Size], then press the button.
1 / 4
Set :
Exit :
4. Use S or T to select the desired setting, then press the
button to confirm.
5. Follow the step 3 and 4 above to set the [Quality].
Quality
Fine
Normal
Economy
Set :
Exit :
1 / 3
ꢀ The possible number of shots and recording time depend on the storage size, resolution and quality settings and
the subject of the image to be captured.
ꢀ You can resize the images later. (Please refer to section in this manual titled “Resizing an Image” for further
detail.)
EN-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Zoom Function
This ViviCam 8400 is equipped with a 3x optical zoom lens allowing you to capture telephoto or wide-
angle shots. By using the optical zoom function, images appear closer by pressing the button, or
smaller by pressing the
button.
You can further enlarge the subjects with 4x digital zoom by continuing to hold the zoom button. This can
be a useful feature, however the more the image is magnified with the digital zoom, the grainier the
resulting image will be.
To capture a zoomed image, perform the following steps:
1. Press the
button to turn on the power.
2. Adjust the magnification ratio by using the
/
button.
„
To access the optical zoom function, press the button as
far as it can go. Press it again to activate the digital zoom.
To exit the zoom photography, press continuously the
button.
The status of digital magnification is displayed on the LCD
monitor.
„
„
/
3. Compose your scene and press the shutter button.
„ The digital magnification ranges from 1.0x to 4.0x.
„ As you record video clips, the zoom function cannot be activated.
EN-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Focus
Images can be captured with the focus determined automatically using auto focus. You may over-ride
the auto focus and specify [ ] macro or [
] infinity.
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M.
2. Press S /
/
.
3. Use S or T to select the desired focus mode.
4. Compose your scene and press the shutter button.
The table below will help you choose the appropriate focus mode:
Focus mode
Description
Macro
Select macro to capture close-up images. When the lens is zoomed to its widest
position you may focus on objects as close as 5 cm.When the lens is zoomed to its
telephoto position (3x zoom) you can focus as close as 30 cm.
Infinity
The infinity setting is useful for shooting through glass and at other times when you
wish to lock on a subject at a long distance.
AF Auto Focus Select auto focus for most occasions when you want the ViviCam 8400 to automatically
determine the focus setting.
Using AF, any object at a distance of 50 cm or greater can be in focus.
EN-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Flash
The flash is designed to function automatically when lighting conditions warrant the use of flash. The
ViviCam 8400 has four flash modes: Auto Flash (default), Red Eye Reduction, Forced Flash and No Flash. You
can record an image using a flash mode that best suits your requirements.
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M.
/
2. Press the
button to turn on the power.
3. Toggle W / until your desired flash mode appears on the LCD
monitor.
4. Compose your image and press the shutter button.
The table below will help you to choose the appropriate flash mode:
Flash mode
AUTO FLASH
Description
The flash fires automatically to suit the photographic conditions.
RED EYE
REDUCTION
Use this mode to reduce the red-eye effect when you want to take
natural-looking photographs of people and animals in low-light conditions.
When taking photographs of people, the red-eye effect can be reduced by
increasing the room lighting if possible and having your subject not look directly
into the camera. The camera’s pre-flash and slight delay in this mode will also
help to improve your images.
FORCED FLASH The flash will always fire regardless of the surrounding brightness. Select this
mode for recording images with high contrast (backlighting) and deep shadows.
NO FLASH
Use this mode if the use of flash is prohibited or if the distance to the subject
is greater than the flash’s maximum range. The camera will adjust its exposure
and shutter speed to give the best results. A tripod will improve your images.
EN-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Self-Timer
The self-timer can be used in situations such as group shots. When using this option, you should either
mount the ViviCam 8400 on a tripod (recommended) or rest it on a flat, level surface.
1. Secure the ViviCam 8400 to a tripod or place it on a stable surface.
/
2. Rotate the mode dial to A , P , SCENE , Tv , Av or M.
3. Press the
button to turn on the power.
4. Toggle X /
until your desired self-timer mode appears on the
LCD monitor.
OFF
2
10
10+2
[ No Indication]
5. Compose your image and press the shutter button.
ꢀ
ꢀ
The self-timer function is activated.
The image is recorded after the preset interval.
ꢀ
To cancel the self-timer at any time, press the
button, switch the mode dial to another mode or press X to
disrupt the sequence.
ꢀ After one shot is taken, the self-timer mode is turned off.
ꢀ If you wish to take another image using the self-timer, repeat these steps.
EN-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Exposure (EV Compensation)
You can manually adjust the exposure determined by the ViviCam 8400. Use this mode when the proper
exposure cannot be obtained, for example, when the contrast (difference between light and dark)
between the subject and the background is extremely large. The EV compensation can be adjusted over
a
range of –2.0EV to +2.0EV.
1. Rotate the mode dial to P , SCENE , Tv , Av or M.
2. Press the
3. Press T/
button to turn on the power.
EV
.
4. Use W or X to set the range of EV compensation to a value
+0.3
between –2.0EV and +2.0EV.
5. To exit from the menu, press the
button.
Select:
OK :
EN-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting White Balance
This feature lets you make adjustments to compensate for different lighting types according to your
shooting conditions.
1. Rotate the mode dial to P , SCENE , Tv , Av or M.
2. Press the button to turn on the power.
3. Press , then the [Mode1] menu is displayed.
Mode1
Image Size
Mode2
Moode3
8M
Q
Quality
4. Use T to select [W. Balance], then press the
button.
W.Balance
5. Use S or T to select the desired setting, then press the
1000
IISO
button to confirm.
6. To exit from the menu, press the
button.
3 / 4
Exit:
W.Balance
Set :
Auto
Daylight
Cloudy
Tungsten
1 / 5
Set :
Exit :
W.Balance
Fluorescent
5 / 5
Set :
Exit :
EN-30
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE MODE DIAL
Simple Mode [ A ]
A (Auto) mode is the simplest way which allows you to take still pictures without having to set special
functions or manual adjustments. The ViviCam 8400 sets the optimal focusing and exposure.
1. Rotate the mode dial to A and turn your ViviCam 8400 on by
pressing the
button.
2. Compose your image with your main subject in the center of the
focus frame.
3. Press the shutter button down halfway to focus the image.
ꢀ
When you press the shutter button down half way, the
ViviCam 8400’s Auto Focus feature automatically focuses the
image. Proper exposure is determined and locked at the same time.
With the shutter button held, you can reframe your image
and the main subject will still be correctly exposed and in focus.
ꢀ
4. Press the shutter button the rest of the way down to capture the image.
Program Mode [ P ]
In the P (Program) mode, the ViviCam 8400 automatically sets the shutter speed and aperture for taking
still images. You can adjust other functions, such as flash mode or continuous shooting mode.
1. Rotate the mode dial to P and turn your ViviCam 8400 on by
pressing the
button.
2. Compose your image with your main subject in the center of the
focus frame.
3. Press the shutter button to capture the image.
EN-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutter Speed Priority Mode [ Tv ]
If you set a fast shutter speed, you can capture images of moving subjects that look as if they are still. If
you set a slow shutter speed, you can capture images that give the impression that the subject is in motion.
1. Rotate the mode dial to Tv and turn your ViviCam 8400 on by
pressing the
button. A guide appears for a few seconds.
Tv
2. Press the
button.
3. Set the shutter speed with W or X, and press the
4. Compose your image on the LCD display.
5. Press the shutter button to capture the image.
button.
1/2S
Select:
OK :
Aperture Priority Mode [ Av ]
In this mode, images are captured with the priority given to aperture. The shutter speed is automatically
set according to the aperture. The aperture will affect the depth-of-field of the picture.
If you set a large aperture (lower F value), you can capture portrait images with an out-of-focus background.
Alternatively, if you set a small aperture (higher F value), both close objects and distant objects will be in
focus, for example when capturing subjects in the foreground together with landscape images.
1. Rotate the mode dial to Av and turn your ViviCam 8400 on by
pressing the
button. A guide appears for a few seconds.
Av
2. Press the
button.
F5.6
3. Set the aperture value with W or X, and press the
4. Compose your image on the LCD display.
button.
Select:
OK :
5. Press the shutter button to capture the image.
EN-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Mode [ M ]
In manual mode, the aperture value and the shutter speed can be varied individually. This can be useful
compensating for tricky lighting conditions, for getting creative results or for capturing night-time scenes.
1. Rotate the mode dial to M and turn your ViviCam 8400 on by
pressing the
2. Press the
button. A guide appears for a few seconds.
button.
Av/Tv
3. Use S or T to select aperture/shutter speed item.
F5.6
1/2S
4. Adjust the value with W or X, and press the
5. Compose your image on the LCD display.
6. Press the shutter button to capture the image.
button.
Select:
OK :
Scene Mode [ SCENE ]
You can select the Picture mode according to the shooting scene. There are 4 available modes in Picture mode.
[
[
[
[
] Night scene: This mode allows you to take photographs of people against a dusk or night-time background.
] Landscape: This mode allows you to take photographs of distant scenery or landscapes.
] Portrait: Select this mode to make people stand out with the background out-of-focus.
] Sport: This mode allows you to shoot fast moving objects.
1. Rotate the mode dial to SCENE and turn your ViviCam 8400 on
by pressing the button. A guide appears for a few seconds.
2. Press the button.
3. Use W or X to select the desired scene mode.
4. Press the button to confirm the selection.
Night Scene
5. Compose your image on the LCD display.
Select:
OK :
6. Press the shutter button to capture the image.
ꢀ Press the shuter button halfway to confirm that the exposure is set correctly on the LCD monitor.
EN-33
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED SHOOTING
Burst
This mode is used for continuous shooting. Pictures are taken continuously while the shutter release
button is pressed.
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M and turn
your ViviCam 8400 on by pressing the button.
Mode3
Mode1
Mode2
Metering
ꢀ
In A (Auto) Mode, press
to access in menu directly.
Capture Mode
Digital Zoom
2. Press
, then use X to select the [Mode2] menu.
3. Use T to select [Capture Mode], then press the
4. Use S or T to select [Burst], then press the
button.
button.
On
5. To exit from the menu, press the
button.
2 / 3
Set :
Exit :
ꢀ
The indicator is displayed on the monitor screen.
6. Press the shutter button halfway to lock the focus.
7. Press the shutter button all the way to shoot.
Capture Mode
Single
Burst
AEB
X1
ꢀ
Shooting will stop when the shutter button is released.
2 / 3
Set :
Exit :
ꢀ In Burst mode, the flash mode will be set to OFF automatically.
EN-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Exposure Bracketing (AEB)
In this mode, the ViviCam 8400 automatically varies the exposure within a set range to take three shots
after you press the shutter button once. AEB settings can be combined with exposure compensation
settings to extend the adjustment range.
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M and turn
your ViviCam 8400 on by pressing the button.
Mode3
Mode1
Mode2
Metering
ꢀ
In A (Auto) Mode, press
to access in menu directly.
Capture Mode
Digital Zoom
2. Press
, then use X to select the [Mode2] menu.
3. Use T to select [Capture Mode], then press the
button.
On
4. Use S or T to select [AEB], then press the
button.
5. To exit from the menu, press the
button.
2 / 3
Set :
Exit :
Capture Mode
ꢀ
The indicator is displayed on the monitor screen.
6. Press the shutter button to capture the series of 3 images, each
with different exposures.
Single
Burst
AEB
X1
Set :
Exit :
3 / 3
ꢀ In AEB mode, the flash mode will be set to OFF automatically.
EN-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Metering Mode
You can select the metering mode that sets which part of the subject to measure to determine the
exposure.
1. Rotate the mode dial to P , SCENE , Tv , Av or M and turn your
Mode3
Mode1
Mode2
ViviCam 8400 on by pressing the
2. Press , then use X to select the [Mode2] menu.
3. Use T to select [Metering], then press the button.
button.
Metering
Capture Mode
Digital Zoom
X1
On
4. Use S or T to select the desired metering mode, then press the
button.
ꢀ
ꢀ
[
Center-Weighted]: Averages the light metered from the
1 / 3
Set :
Exit :
entire frame, but gives greater weight to the subject matter
at the center.
Metering
[
Spot]: Meters the area within the spot automatic
exposure point frame at the center of the LCD monitor.
5. To exit from the menu, press the button.
Center-Weighted
Spot
6. Compose your image in the LCD display.
7. Press the shutter button to capture the image.
2 / 2
Set :
Exit :
EN-36
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE - THE BASICS
Viewing Images
You can display the still images you have just captured.
1. Press the
2. Press the
button to turn on the ViviCam 8400.
(Playback) button.
SD
ꢀ
The last recorded image appears on the LCD monitor.
100-0001
SIZE
3. Use W or X to select the desired images.
1600 x 1200
+1.5
ꢀ
ꢀ
To view the previous image, press the W button.
To view the next image, press the X button.
EV.
05:22
01. 04. ’04
1
ꢀ The playback information displayed on the LCD monitor will disappear after a few seconds.
ꢀ If there is no image stored in the internal memory or on the memory card. a [No Image] message will appear on
the monitor.
EN-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnifying Images
While reviewing your images, you may enlarge a selected portion of an image. This magnification allows
you to view fine details. The zoom factor displayed on the screen shows the current magnification ratio.
T
1. Press the
(Playback) button.
ꢀ
ꢀ
ꢀ
The last recorded image appears on the LCD monitor.
To view the previous image, press the W button.
To view the next image, press the X button.
2. Adjust the zoom ratio by using the Zoom
/
button.
To enlarge the selected image, press the button.
To return to the normal image, press the button.
The magnification factor is displayed on the LCD monitor.
ꢀ
ꢀ
ꢀ
2.0X
T
3. To view different portion of the images, press the S / T / W / X
button to adjust the display area.
ꢀ The magnification factors range from 1x to 4x (within 7 stages: 1.0x, 1.5x, 2.0x, 2.5x, 3.0x, 3.5x and 4.0x).
EN-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Thumbnail Display
This function allows you to view 9 thumbnail images on the LCD monitor simultaneously so you may
search for a particular image.
1. Press the
ꢀ The last recorded image appears on the LCD monitor.
2. Press the button once.
Nine thumbnail images are displayed simultaneously.
(Playback) button.
SD
/
1
4
3
6
2
5
ꢀ
ꢀ
For recorded video clips, the
displayed.
video mode icon will be
3. Use the S / T / W / X button to move the cursor to select the
9
7
8
image to be displayed at regular size.
4. Press the
button to display the selected image on full screen.
EN-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Slideshow Display
The slide show function enables you to play your images back automatically in sequential order. This is
very useful for reviewing recorded images and for presentations.
1. Press the
(Playback) button.
Playback1
Playback2
ꢀ
The last recorded image appears on the LCD monitor.
SLIDE
Slide Show
Protect
SHOW
2. Press . The [Playback1] menu is displayed.
3. Use T to select [Slide Show] and press the
button.
4. Use S or T to set the playback interval, then press the
button.
ꢀ
ꢀ
The slide show starts.
The video clips display only the first frame image and are not
played back.
1 / 2
Exit :
Slide Show
Set :
ꢀ
To stop slide show, press the
button.
3 Sec.
5 Sec.
10 Sec.
Set :
Return :
ꢂ
ꢀ You can adjust the slide show display interval within the range of 3 Sec., 5 Sec., 10 Sec.
EN-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Resizing an Image
You can change the image size of a captured image to one of the following sizes: 2848 x 2136 pixel,
2272 x 1704 pixel, 1600 x 1200 pixel and 640 x 480 pixel.
1. Press the
(Playback) button.
Playback1
Playback2
ꢀ The last recorded image appears on the LCD monitor.
Resize
R
2. In
(Playback) mode, use W or X to select the desired images.
ꢀ To view the previous image, press the W button.
ꢀ To view the next image, press the X button.
Quality Change
Copy To Card
COPY
3. Press
, then use X to select the [Playback2] menu.
button.
4. Use S or T to select [Resize] and press the
Set :
Exit :
1 / 3
5. Use S or T to select the desired setting, then press the
button
to confirm.
Resize
2848 X 2136
2272 X 1704
1600 X 1200
640 X 480
Set :
Return :
EN-41
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips with sound using the built-in microphone.
1. Rotate the mode dial to
mode and turn your ViviCam 8400
on by pressing the button.
2. Press the shutter button to start recording.
3. To stop recording, press the shutter button again.
SD
00:49
[
]
ꢀ The zoom function of optical zoom (3x) can be activated before you start to record video clips.
ꢀ Pressing the button switches the LCD monitor display mode. Each time you press the
display changes in the following order: Focus Frame On ꢁ Indicators Off ꢁ Composition Line On ꢁ LCD Off.
/
/
button, the
EN-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Video Clips
You can play back recorded video clips. A guide to operation appears on the LCD monitor during the
video playback.
1. Press the
(Playback) button.
SD
2. Use W or X to go through the images until the video clip you
want to play back is displayed.
100-0001
SIZE
ꢀ
ꢀ
To view the previous image, press the W button.
640 x 480
+1.5
To view the next image, press the X button.
EV.
05:22
01. 04. ’04
3. Press the
button to start playing back the video clips.
1
ꢀ
To pause or resume video playback, press the
again.
button
ꢀ The playback information displayed on the LCD monitor will disappear after a few seconds.
ꢀ The zoom function cannot be activated while playing the video clips.
ꢀ To playback the video clips on the computer, we recommend using Windows Media Player 9.0 (WMP 9.0).
EN-43
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE – ADVANCED FEATURES
Playing Back Still Images/Video Clips on TV
You can also playback your images on a TV screen. Before connecting to any device, make sure to
select NTSC/PAL system to match the video output system of the video equipment you are going to
connect to the ViviCam 8400, then turn all devices off.
1. Connect one end of the A/V cable to the A/V terminal of the
ViviCam 8400.
2. Connect the other end to the A/V input jacks of the TV set.
3. Turn on the TV and ViviCam 8400.
4. Playback the images/video clips.
V T
ꢀ
The method of operation is the same as playing back still
images and video clips on the ViviCam 8400.
ꢀ The sound recorded with video clips can only be played back on TV or computers.
EN-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Images/Video Clips
Use this function to delete one or all images/video clips stored in the internal memory or memory card.
Please note that the deleted images or video clips cannot be recovered. Exercise caution before
deleting a file.
1. Rotate the mode dial to A , P , SCENE , Tv , Av , M or
your ViviCam 8400 on by pressing the button.
2. Press the button.
The last recorded image appears on the LCD monitor.
3. Use W or X to select the image you want to delete.
4. Press the button.
and turn
Delete
This Image
All Images
Cancel
ꢀ
5. Use S or T to select [This Image] or [All Images], then press the
button.
Set :
6. When the delete message appears, use S or T to select [Yes],
then press the
button to confirm the deletion.
Delete
Yes
ꢀ If you wish to cancel the deletion, select [No].
No
Set :
ꢀ Protected images cannot be deleted with the delete function.
EN-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Protecting Images/Video Clips
Sets the data to read-only to prevent images from being erased by mistake.
1. Press the
(Playback) button.
Playback1
Playback2
ꢀ The last recorded image appears on the LCD monitor.
SLIDE
Slide Show
Protect
SHOW
2. In
(Playback) mode, use W or X to select the desired images.
ꢀ To view the previous image, press the W button.
ꢀ To view the next image, press the X button.
3. Press . The [Playback1] menu is displayed.
4. Use T to select [Protect] and press the
button.
2 / 2
Exit :
Protect
Set :
5. Use S or T to choose the desired setting, then press the
button.
Protect One
Protect All
ꢀ
ꢀ
[Protect One]: Protect one image/movie.
[Protect All]: Protect all images/movies (at once).
6. Use S or T to select [Lock], then press the
button to confirm.
(Playback) mode.
indicator appears on the selected image.
ꢀ
Press
The
to return to the
Set :
Return :
ꢀ
If you wish to cancel the protect function, select [Unlock].
Protect One
Lock
Unlock
Set :
Return :
EN-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a PictBridge Compliant Printer
Even if you do not have a computer, you can connect the camera directly to a printer that supports
PictBridge to perform image selection and printing using the camera monitor screen and controls. You
may also specify which images you want to print and how many copies of each should be printed.
Connecting the camera to the printer
1. Rotate the mode dial to
the button.
2. Press X to select the [Set-up2] menu, then use T to select
and turn your camera on by pressing
USB Mode
PC
[USB Mode].
PictBridge
3. Use S or T to select [PictBridge], then press the
button.
4. Connect your camera and the printer via a supplied USB cable.
„
The screen turns off automatically and the setting screen wil
appear on the monitor after a few seconds.
OK
2 / 2
Set :
Printing images
When the camera is properly connected to a PictBridge compliant printer, the [Printing Mode Select]
screen is displayed on the monitor. Use S or T to select the print mode.
„
In [Print] Mode: Lets you print the specified image with PictBridge.
Step
Figure
Procedure
Use S or T to select the [Print] mode, then press the
* The [Print Paper] screen is displayed.
button.
Printing Mode Select
Print
1
OK
Set
:
Select
:
EN-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Procedure
Figure
Print Paper
Use S or T to access in the selection of paper setting, then press the
button to confirm.
Standard
Standard
Size
Borderless
Cancel
2
[Size]:
You may select the desired item depending on the
type of printer being used.
OK
Set
:
Select
:
[Borderless]:
[Cancel]:
You may select the desired item depending on
the type of printer being used.
To cancel the setting, use S or T to select [Cancel].
Use W or X to select the image you want to print, then press T to go to
more detailed settings.
3
* The [Print Info] screen is displayed.
OK
Print
:
Select
Cancel
:
Set
:
:
Use S or T to select your preference, then press the
button.
Print Info
Quantity
10
* After the print settings finished, the printer icon will be displayed as
shown in the figure of step 5.
4
With
With
Date
File Name
Cancel
[Quantity] :
Specifies the number of prints. You can select the number
up to 10.
OK
Set
:
Select
:
[Date]:
If you select With, images are printed with the date.
[File Name]: If you select With, images are printed with the file name.
[Cancel]: To cancel the print settings, use S or T to select [Cancel].
After step 4 is completed, you can still use W or X to select other images.
Follow the same instructions and print settings as in step 4, then press the
button to print.
100-0001
OK
5
Print
Set
:
Select
Cancel
:
:
:
EN-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Figure
Procedure
Print
Print
Use S or T to select [Print], then press the
* The “Transferring” screen is displayed.
button to confirm.
Cancel
Total: 2
6
OK
Set
:
Select
:
This starts printing and displays the message “Transferring” on the monitor
screen. The message will disappear after the printing is finished.
Tr ans fer r ing
1/2
Cancel
:
7
* To cancel printing:
Print
Continue
Pressing the
button during print data transfer displays the screen for
Cancel
selecting whether to [Continue] or [Cancel] printing.
OK
Set
:
Select
:
EN-49
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING FILES FROM YOUR VIVICAM 8400
TO YOUR COMPUTER
After using the USB cable to establish a connection between the ViviCam 8400 and your computer, you
can use your computer to share recorded images or video clips with your family or friends via e-mail or post
them on the Web. In order to do this, you must install the USB driver onto your computer first. Note that
before you begin to install the software, you need to check your system according to the table as shown
below.
System Requirements
(Windows)
System Requirements
(Macintosh)
CPU
Pentium III 600 MHz processor or higher PowerPC G3/G4/G5
Operating System
RAM
Windows 98/98SE/ME/2000/XP
OS 9.0 or higher
32MB
32MB
(64MB RAM recommended)
(64MB RAM recommended)
Hard Disk Space
Required Devices
128MB hard disk space
A CD-ROM drive
128MB hard disk space
A CD-ROM drive
An available USB port
Color Monitor (800x600, 24-bit
or higher recommended)
An available USB port
Color Monitor (800x600, 24-bit or
higher recommended)
Display
EN-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Install the USB driver
ꢀ
Installation on Windows 98 & 98SE
The USB driver on the supplied CD-ROM is exclusively for Windows 98 and 98SE. Windows 2000/ME/XP
users need not install the USB driver.
1. Insert the enclosed CD-ROM into your CD-ROM drive.
2. When the welcome screen appears, click “Install USB Driver”.
Follow the on-screen instructions to complete the installation.
3. After the USB driver has been installed, restart your computer.
ꢀ
Installation on MAC OS 9.0
For Mac OS 9.0 or higher, the computer will automatically recognize the ViviCam 8400 and load its own
USB drivers.
EN-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Connect the ViviCam 8400 to your computer
1. Rotate the mode dial to
pressing the button.
and turn your ViviCam 8400 on by
Set-up2
Set-up3
PC
Set-up1
USB Mode
2. Press X to select the [Set-up2] menu, then use T to select [USB
NTSC
PAL
TV
NTSC
Mode].
LCD Brightness
Auto Shut Down
3. Use T to select [PC], then press the
button.
3 Min.
4. Connect one end of the USB cable to an available USB port on
your computer.
Set :
1 / 4
5. There will be a new “Removable Disk” icon detected in “My
Computer”, in which contains your recorded images or video
clips.
PC
(For Mac users, double-click [untitled] or [unlabeled] disk drive
icon on our desktop.)
PictBridge
1 / 2
EN-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Download images or video clips
When the ViviCam 8400 is turned on and connected to your computer, it is considered to be a disk drive,
just like a floppy disk or CD. You can download (transfer) images by copying them from the “Removable
disk” (“untitled” or “unlabeled” disk on a Macintosh) to your computer hard drive.
ꢀ
Windows
Open the “removable disk” and double click on the DCIM / DSCIM folder to open it to find more folders.
Your images are inside these folder(s). Select the desired still images or video clips and then choose
“Copy” from the “Edit” menu. Open the destination location (folder) and choose “Paste” from the “Edit”
menu. You may also drag and drop image files from the ViviCam 8400 to a desired location.
ꢀ
Macintosh
Open the “untitled” disk icon, and the destination location on your hard disk. Drag and drop from the
ViviCam 8400 to the desired destination.
ꢀMemory card users may prefer to use a memory card reader (highly recommended).
ꢀVideo playback application is not included with the package. Make sure that video playback application has
been installed in your computer.
EN-53
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING SOFTWARE INSTALLATION
Installing Photo Explorer
Ulead® Photo Explorer provides a simple and efficient way to transfer, browse, modify and distribute
digital media. Acquire photos, video or sound clips from various digital device types and easily browse
or add personal descriptions; make timely modifications; or distribute the media through the medium of
your choice: E-mail, Print, Slideshow Presentations. It is an indispensable all-in-one tool for owners of
ViviCam 8400, WebCams, DV camcorders, scanners, or anyone who strives to effectively organize a
large collection of digital media.
1. Insert the enclosed CD-ROM into your CD-ROM drive.
2. When the welcome screen appears, click “Install Ulead® Photo
Explorer”. Follow the on-screen instructions to complete the
installation.
ꢀFor more information about the operation of Photo Explorer application software, refer to its respective help
documentation.
ꢀFor Windows 2000/XP users, please make sure to install and use the Photo Explorer in “Administrator” mode.
ꢀPhoto Explorer is not supported on the Mac. iPhoto or iPhoto2 is recommended.
EN-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Photo Express
Ulead® Photo Express is complete photo project software for digital images. The step-by-step workflow,
visual program interface, and in-program help assist users in creating exciting photo projects. Acquire
digital photos effortlessly from ViviCam 8400 or scanners. Organize them conveniently with the Visual
Browse mode. Use hundreds of ready-to-use templates such as albums, cards, posters, slideshows, and
more. Edit and enhance images with photo editing tools, photographic filters, and special effects.
Embellish projects by adding creative design elements such as frames, callouts, and stamp objects.
Share results with family and friends via e-mail and multiple print options.
1. Insert the enclosed CD-ROM into your CD-ROM drive.
2. When the welcome screen appears,click “Install Ulead® Photo
Express”. Follow the on-screen instructions to complete the
installation.
ꢀ For information on how to use Photo Express to edit and retouch your recorded images, please refer to its online
help.
ꢀ For Windows 2000/XP users, make sure to install and use the Photo Express while logged in as a user with an
Administrator account.
ꢀ Photo Express is not supported on the Mac.
EN-55
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING ADOBE ACROBAT READER
The CD-ROM includes a PDF (portable document format) copy of the user’s manual. To view a PDF you
must have Adobe Acrobat Reader installed in your computer. Adobe Acrobat Reader is included on the
ViviCam 8400 CD ROM. Using Adobe Acrobat Reader, you can read the user’s manual and print
sections of interest.
1. Insert the CD-ROM that came with the ViviCam 8400 into the
CD-ROM drive. The welcome screen appears.
2. Click “Install Acrobat Reader”.
Follow the on-screen instructions to complete the installation.
EN-56
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
A copy of the user manual is provided on the CD-ROM in PDF format. It is a backup copy of the printed
manual.If you misplace the printed guide, you may print another copy from the CD-ROM. The only
requirement for viewing the User Manual on the CD-ROM is that you have Acrobat Reader (Adobe
Reader) installed on your computer. Updates to this manual, and versions in other languages may be
found on the Vivitar website (www.vivitar.com).
1. Insert the CD-ROM that came with the ViviCam 8400 into the
CD-ROM drive. The welcome screen appears.
2. Click “Install User’s Manual”. Follow the on-screen instructions
to complete the installation.
Alternatively, browse the CD-ROM to find the PDF file.
EN-57
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPTIONS
Camera Menu
This menu is for the basic settings to be used when capturing still images.
Mode3
Mode1
Mode2
Mode1
Color
Mode2
Mode1
Mode2
Mode3
Auto
Image Size
Quality
Mode3
8M
Metering
Image Size
8M
X1
Q
Q
Quality
W.Balance
ISO
Medium
Sharpness
Saturation
Date Imprint
Capture Mode
Digital Zoom
Capture Mode
Medium
Off
On
100
2 / 3
1 / 3
Set :
Exit :
Set :
Exit :
Set :
1 / 4
1 / 4
Exit :
Exit:
Set :
1. Rotate the mode dial to A , P , SCENE , Tv , Av or M and turn your ViviCam 8400 on.
2. Press
, then use W or X to select the [Mode1] / [Mode2] / [Mode3] menu.
ꢀ
In A (Auto) Mode, press
to access in menu directly.
3. Press S or T to select the desired setting, then press the
button.
4. To exit from the menu, press the
button.
ꢀIn A (Auto) Mode
Item
Functional Description
Sets the size of the image that will be captured.
Image Size
*
*
*
*
3264 x 2448
2272 x 1704
1600 x 1200
640x480
Quality
Sets the quality (compression rate) at which the image is captured.
*
*
*
Fine
Normal
Economy
Q
EN-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Functional Description
Capture
Mode
Sets the recording method at the time of taking pictures.
*
*
*
Single
Burst
AEB
X1
ꢀIn P , SCENE , Tv , Av or M Mode
Mode1
Item
Functional Description
Image Size
Refer to “Camera Menu - In A (Auto) Mode” in LIST OF MENU
OPTIONS.
Quality
Refer to “Camera Menu - In A (Auto) Mode” in LIST OF MENU
Q
OPTIONS.
W. Balance
Sets the white balance photographing under a variety of lighting
conditions and permits photographs to be taken that approach the
conditions that are seen by the human eye.
WB
*
*
*
*
*
Auto
Daylight
Cloudy
Tungsten
Fluorescent
EN-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode1
Mode2
Item
Functional Description
ISO
Sets the sensitivity for taking pictures. When the sensitivity is raised
(and the ISO figure is increased), photography will become possible
even in dark locations, but the more pixilated (grainer) the image will
appear.
ISO
*Auto / 50 / 100 / 200
Item
Functional Description
Metering
Refer to section in this manual titled “Selecting the Metering Mode” for
further details.
Capture
Mode
Refer to “Camera Menu - In A (Auto) Mode” in LIST OF MENU OPTIONS.
Digital Zoom
This sets whether or not to use digital zoom at the time of shooting.
* On / Off
EN-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode3
Item
Functional Description
Color
Sets the color of the image that will be captured.
*
*
*
Full Color
Black & White
Sepia
Sharpness
Saturation
Sets the level of image sharpness.
*
*
*
High
Medium
Low
To capture an image, your ViviCam 8400 offers you three different
degrees of color to match with your preference.
Your images will show different effects by changing the degrees of
color. This is called “Saturation”.
*
*
*
High
Medium
Low
Date Imprint
The date of recording can be printed directly on the still images. This
function must be activated before the image is captured. The date
appears on the right bottom of the captured picture. When images
are shot with date imprint feature, the date cannot be removed later.
* On / Off
DATE
EN-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Menu
This menu is for the basic settings to be used when recording video clips.
Video
R
G
Color
B
Digital Zoom
On
Set :
Exit :
1 / 2
1. Rotate the mode dial to
2. Press , then use S or T to select the option item, then press the
3. Use S or T to select the desired setting, and press the button.
4. To exit from the playback menu, press the button.
mode and turn your ViviCam 8400 on.
button.
Item
Functional Description
Color
REFER TO “Camera Menu-In In P , SCENE , Tv , Av or M Mode (Mode3)” of
MENU OPTIONS.
Digital Zoom
REFER TO “Camera Menu-In In P , SCENE , Tv , Av or M Mode (Mode2)” of MENU
OPTIONS.
EN-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Menu
In the
(Playback) menu, you can choose the settings to be used for playback.
Playback1
Playback2
Playback1
Playback2
SLIDE
SHOW
Slide Show
Protect
Resize
R
Quality Change
Copy To Card
COPY
1 / 2
Set :
Exit :
1 / 3
Exit :
Set :
1. Press the
The last recorded image appears on the LCD monitor.
2. Press ,then use W or X to select [Playback1] or [Playback2] menu.
3. Use S or T to select the desired setting and press the button.
4. To exit from the playback menu, press the button.
(Playback) button.
ꢀ
ꢀ
[Playback1] settings
Item Functional Description
Slide Show
You can play back recorded images in order choosing the time delay between frames.
This function is useful for checking your images or for presentations, etc.
Refer to the section in this manual titled “Slideshow Display” for further details.
* 3 Sec. / 5 Sec. / 10 Sec.
SLIDE
SHOW
Protect
Set the data to read-only to prevent images from being erased by mistake.
Refer to the section in this manual titled “Protecting Images/Movie clips” for further details.
EN-63
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
[Playback2] settings
Item
Functional Description
Resize
Changes the size of a recorded image.
Resizing replaces the original image with the changed image. Only resizing to the
smaller size is available.
R
*
*
*
*
2848 x 2136
2272x1704
1600x1200
640x480
Quality Change Change the quality (compression rate) of a recorded image.
Compresses images down to half of their size or more, overwrites an old size image
with a newly compressed image. Only quality changing to the lower quality level is
available.
*
*
*
Fine
Normal
Economy
Copy To Card Allows you to copy your files from the ViviCam 8400’s internal memory to a memory
card. Of course, you can only do this if you have a memory card installed and some
COPY
files in internal memory.
* Yes / No
EN-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
This feature allows you to choose your ViviCam 8400‘s default settings.
Set-up2
Set-up3
Set-up2
Set-up1
Set-up2
Set-up3
Set-up1
Set-up1
Set-up3
PC
1
Format
Reset Number
USB Mode
NTSC
PAL
Beeper
Louder
TV
NTSC
Set to Default
Date & Time
m/d/y
LCD Brightness
Auto Shut Down
Y/M/D
V.
Version
Language
English
3 Min.
Set :
Set :
Set :
1 / 3
1 / 4
1 / 4
1. Rotate the mode dial to
(Setup) mode and turn your ViviCam 8400 on.
2. Press ,then use W or X to select the [Set-up1] / [Set-up2] / [Set-up3] menu.
3. Use S or T to select the desired option item, then press the
4. To exit from the setup menu, turn the dial to any other mode.
ꢀ[Set-up1] settings
button.
Item
Functional Description
Format
Erases all images and reformats the SD card loaded in your ViviCam 8400. Protected
images are also erased. SD card cannot be formatted if it is write-protected.
Refer to the section in this manual titled “Formatting an SD Memory Card or Internal
Memory” for further details.
* Yes / No
Beeper
This sets whether or not to mute the startup sound, and the camera sound each
time you press a camera button.
* Louder / Soft / Off
Date & Time
This sets the date and the time.
Refer to the section in this manual titled “Setting the Date and Time” for further details.
Y/M/D
Language
Sets the language that is displayed on the LCD monitor.
Refer to the section in this manual titled “Choosing the Screen Language” for further details.
* English / Français / Deutsch / Español / Italiano /
/
EN-65
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ[Set-up2] settings
Item
Functional Description
USB Mode
Selects to choose one of the following modes for further settings.
* PC / PictBridge
TV
NTSC
Sets video output of the ViviCam 8400 for matching the video output system of
the equipment that you are going to connect to the ViviCam 8400.
* PAL / NTSC
PAL
LCD Brightness This sets the brightness of the LCD monitor.
The adjustment range is from -5 to +5.
Auto Shut Down If no operation is performed for a specific period of time, the power to the ViviCam 8400
is automatically turned off. This feature is useful to reduce battery wear.
* 2 Min. / 3 Min. / 5 Min. / Off
ꢀ[Set-up3] settings
Item
Functional Description
Reset Number
Sets whether or not to reset the file number when you take photographs. This
creates a new folder. The captured images are recorded to the newly created
folder from number 0001. If you want to reset the file number, be sure that no
images are recorded in the internal memory or the SD memory card.
* Yes / No
1
Set to Default
Returns all basic settings to the ViviCam 8400’s default settings. The time setting
will not be reset.
* Yes / No
D
Version
This displays the current firmware version of the ViviCam 8400.
V.
EN-66
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE VIVICAM 8400 TO OTHER DEVICES
EN-67
Download from Www.Somanuals.com. All Manuals Search And Download.
VIVICAM 8400 SPECIFICATIONS
Item
Description
Image Sensor
Effective pixels
Image size
CCD
8.0 Mega pixels
Still image: 3264 x 2448, 2272 x 1704, 1600 x 1200, 640 x 480
Video clip: 640 x 480
Image quality
Still image: Fine, Normal, Economy
Movie image: Economy
Recording media
32MB internal memory
SD memory card (Optional, up to 1GB)
Still image: JPEG; Video: ASF
F-no.: Wide: 2.8 / Tele: 4.8
Focal length: 7.5mm~22.5mm (Equivalent 36~108mm)
Normal: 50 cm (20 in.)-infinity
Wide: 6 cm (2.5 in.)-infinity
File format
Lens
Focus range
Tele: 30 cm (12 in.)-infinity
LCD monitor
Self-timer
2.0” LTPS color LCD
High-resolution 130K pixel display
10 sec delay, 2 sec delay, 10+2 sec delay
Exposure compensation -2.0EV~ +2.0EV (in 0.3EV increments)
White balance
ISO
Auto, Daylight, Cloudy, Tungsten, Fluorescent
Auto, 50, 100, 200
Interface
Power
DC-IN jack, USB connector, A/V terminal
2xAA Alkaline or optional Ni-MH Batteries (2000 mAh or higher suggested)
AC-DC Adapter (3V/2.5A) (Optional)
Dimensions
Weight
Approx. 91 x 61 x 27 mm (3.6 x 2.4 x 1.1 in.)
Approx. 150g (5.3oz) (without batteries and the SD card)
* Design and specifications are subject to change without notice.
EN-68
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
„ Troubleshooting Guide
Symptom
Possible causes
Solutions / Corrective Actions
* The batteries are depleted.
The camera does not
power on.
*
*
*
*
Load new or fully charged batteries.
Ensure that the battery polarity is correct.
Close the battery cover correctly.
Properly connect the AC power adapter.
* The batteries are not oriented correctly.
* The battery cover is not closed properly.
* The AC power adapter (optional) is disconnected.
* The function of Auto Shut Down in
(Setup) mode has been activated.
* The batteries are depleted.
*
*
Set the option of Auto Shut Down to Off.
Press the power button again or
replace the batteries with a new or
freshly charged set.
The ViviCam 8400
suddenly powers down.
*
Rotate the mode dial to A , P , SCENE
, Tv , Av or M.
Transfer the desired files to your
computer and then delete unnecessary
files, or use a different memory card.
* The ViviCam 8400 is in
* Memory is full.
(Play) mode.
The image is not
captured when the
shutter button is
pressed.
*
*
*
Select a different flash mode.
* NO FLASH is selected in flash mode.
The flash does not fire.
Select [Single] in the capture mode .
* The ViviCam 8400 is in Burst/AEB/
(Video) mode.
Continuous shooting
is not possible.
* The capacity of the built-in memory or
SD memory card is full.
*
Insert a new SD memory card.
Cannot transfer files
over a USB connection.
* The USB cable is not connected securely.
* The USB driver is not installed.
* The ViviCam 8400 is turned off.
*
*
*
Check all connections.
Install the USB driver on your computer.
Turn on the ViviCam 8400.
EN-69
Download from Www.Somanuals.com. All Manuals Search And Download.
„ Possible Number of Recordable Images
The frame counter indicates the approximate number of images that can be stored on the SD memory card. The
number of recordable images may vary depending on the recorded subject, the capacity of the memory card, there
are files other than images or when the recording is made while switching the picture quality or resolution.
Quality
SD Memory Card
Resolution
(Compression
Ratio)
Fine (1/4)
Normal (1/8)
Economy (1/16)
Fine (1/4)
Normal (1/8)
Economy (1/16)
Fine (1/4)
Normal (1/8)
Economy (1/16)
Fine (1/4)
Normal (1/8)
Economy (1/16)
32MB
Internal Memory
32MB
64MB 128MB 256MB 512MB 1GB
14
3264 x 2448
7
14
28
14
29
58
29
59
118
185
371
743
7
15
30
15
31
63
31
63
127
198
397
794
31
63
63
128
256
256
512
29
59
30
126
253
130
127
65
512
264
1024
528
2272 x1704
1600 x 1200
640 x 480
61
122
61
123
246
385
770
1540
131
262
132
264
528
826
1653
3306
261
522
263
527
1054
1647
3294
6589
528
1057
533
1066
2132
3331
6662
13325
1057
2114
1065
2131
4263
6661
13322
26644
* The above data shows the standard testing results. The actual capacity varies according to the shooting
conditions and settings.
„ Approximate Duration of Recording Time
The table below indicates the approximate duration of recording time depending on the capacity of the SD memory card.
Image size
SD Memory Card
128MB
32MB Internal Memory
1'09"
32MB
1'47"
64MB
3'28"
256MB
14'52"
512MB
30'04"
1GB
01:00:07
640 x 480
7'27"
* The values for the recording time may vary depending on the shooting conditions and settings.
EN-70
Download from Www.Somanuals.com. All Manuals Search And Download.
|