Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-845-4641
Counter-Depth
Freestanding French Door
Bottom-Mount Refrigerator/Freezer
(022213)
F21169 EN
W10581473
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT–Please Read and Follow
Refrigerator Safety
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local
ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to any significant
sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not installed
properly or do not meet the requirements below.
If the use of a GFI is required, it should be:
• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles, switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Sheltered from moisture (water, steam, high humidity) as much as reasonably possible
IMPORTANT SAFETY INSTRUCTIONS
Proper Disposal
(of old refrigerator)
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
•Plug into a grounded 3 prong outlet.
•Do not remove ground prong.
•Use nonflammable cleaner.
•Keep flammabel materials and vapors, such as gasolne,
away from refrigerator
IMPORTANT:
•Do not use an adapter.
•Do not use an extension cord.
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous - even if they will
sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these
instructions to help avoid accidents.
•Use two or more people to move and install refrigerator.
•Disconnect power before installing ice maker (on ice maker
kit ready models only).
•Disconnect power before servicing.
•Replace all parts and panels before operating.
•Remove doors from your old refrigerator.
•Use a sturdy glass when dispensing ice (on some models).
SAVE THESE INSTRUCTIONS
Before You Throw Away Your Old Refrigerator
or Freezer:
• Take off the doors.
• Leave the shelves in place so that children may
not easily climb inside.
WARNING
State of California Proposition 65 Warning
• This product contains one or more chemicals known to the State of California to cause cancer.
• This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
(Professional)
Specifications
French Door Bottom-Mount
Description
Overall width
Overall height
VCFF236
35-5/8” (90.5 cm)
To top of door: 71-7/8” (182.6 cm)
To top of cabinet: 70-7/8” (180.0 cm)
Overall depth from rear
Cutout height
To front edge of cabinet:
To front of door:
To front of handle endcap:
23-7/8” (60.6 cm)
27-5/8” (70.2 cm)
30-1/8” (76.5 cm)
Back of refrigerator - 71-3/8" (181.3 cm)
Front of refrigerator - 72-3/8" (183.8 cm)
44-1/4”
(112.4 cm)
Cutout width
36” (91.4 cm)
Cutout depth
24-1/2” (62.2 cm)
71-7/8”
(182.6 cm)
Electrical requirements
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
Maximum amp usage
7.1 amps
Inlet water requirements
1/4” copper tubing inlet waterline; minimum 35 psi; maximum 120 psi
Overall interior capacities
Refrigerator
Freezer
Total capacity
Approximate shipping weight
70-7/8”
16.3 cu. ft. (461.6 liters)
5.5 cu. ft. (155.7 liters)
21.8 cu. ft. (617.3 liters)
355 lbs. (160 kg)
(180.0 cm)
26-1/2”
(67.3 cm)
30-1/8”
(76.5 cm)
35-5/8”
(90.5 cm)
23-7/8”
(60.6 cm)
27-5/8”
(70.2 cm)
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
(with Grille/Side Panels/Top)
Specifications
(with Grille/Side Panels/Top)
French Door Bottom-Mount
Description
VCFF236 with Top, Top Grille Kit & Side Panels
Overall width
Addition of side panel: 35-7/8” (91.1 cm)
35-7/8”
w/side panels accessory
(91.1 cm)
Overall height
To top of cabinet with addition to top kit: 73-5/8" (187.0 cm)
Overall depth from rear
To front edge of cabinet:
To front of door:
To front of handle endcap:
23-7/8” (60.6 cm)
27-5/8” (70.2 cm)
30-1/8” (76.5 cm)
Cutout height
Addition of top grilles//top kit: 73-3/4" (187.3 cm)
36” (91.4 cm)
Cutout width
Cutout depth
24-1/2” (62.2 cm)
Electrical requirements
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
44-1/4”
(112.4 cm)
Maximum amp usage
7.1 amps
Inlet water requirements
1/4” copper tubing inlet waterline; minimum 35 psi; maximum 120 psi
71-7/8”
Overall interior capacities
Refrigerator
(182.6 cm)
16.3 cu. ft. (461.6 liters)
5.5 cu. ft. (155.7 liters)
21.8 cu. ft. (617.3 liters)
355 lbs. (160 kg)
Freezer
Total capacity
Approximate shipping weight
73-5/8"
w/top panel and top grille kit
26-1/2”
(187.0 cm)
(67.3 cm)
30-1/8”
(76.5 cm)
35-5/8”
(90.5 cm)
23-7/8”
(60.6 cm)
27-5/8”
(70.2 cm)
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
General Information
Your refrigerator was packed carefully for
shipment. Remove and discard all packaging and
tape. DO NOT remove the model/serial number
label.
Clean Before Using
Electrical Requirements
After you remove all of the packaging materials,
clean the inside of your refrigerator before using
it. See the cleaning instructions in “Use and
Care Guide.”
To ensure proper ventilation for your refrigerator,
allow for a 1/2" (1.25 cm) space on each side and
at the top. Allow 1/2" (1.3 cm) of space behind
the refrigerator. If your refrigerator has an ice
maker, allow extra space at the back for the water
line connections. When installing your refrigerator
next to a fixed wall, leave a 2-3/4" (7.0 cm)
minimum space between the refrigerator and wall
to allow the door to swing open.
Important information to know about glass
shelves and covers:
DO NOT clean glass shelves or covers with warm
water when they are cold. Shelves and covers
may break if exposed to sudden temperature
changes or impact, such as bumping. For your
protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is
normal. Glass shelves and covers are heavy. Use
special care when removing them to avoid impact
from dropping.
Overhead View
Wall
Remove the Packaging
1/2”
(1.27 cm)
• Remove tape and glue residue from surfaces
before turning on the refrigerator. Rub a small
amount of liquid dish soap over the adhesive
with your fingers. Wipe with warm water and
dry.
2-3/4”
(6.99 cm)
Before you move your refrigerator to its final
location, it is important to make sure you have
the proper electrical connection.
• DO NOT use sharp instruments, rubbing
alcohol, flammable fluids, or abrasive cleaners
to remove tape or glue. These products can
damage the surface of your refrigerator. For
more information, see “Refrigerator Safety.”
• Dispose of/recycle all packaging materials.
Door
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused,
grounded electrical supply is required. It is
recommended that a separate circuit serving only
your refrigerator be provided. Use an outlet that
cannot be turned off by a switch. DO NOT use an
extension cord.
Moving Unit
When moving your refrigerator:
Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to
protect the floor. Always pull the refrigerator
straight out when moving it. DO NOT wiggle or
“walk” the refrigerator when trying to move, as
floor damage could occur.
• DO NOT transport the refrigerator on its side. If
an upright position is not possible, lay the
refrigerator on its back. Allow refrigerator to sit
upright for approximately 30 minutes before
plugging it in to assure oil returns to the
compressor. Plugging the refrigerator in
immediately may cause damage to internal
parts.
Location Requirements
Note: Before performing any type of installation,
cleaning, or removing a light bulb, turn the
cooling OFF. Disconnect the refrigerator from the
electrical source. When you are finished,
reconnect the refrigerator to the electrical source
and turn cooling on.
• DO NOT install refrigerator near oven, radiator
or other heat sources. If not possible, shield
refrigerator material.
• DO NOT install where the temperature falls
below 55°F (13°C) or rises above 110°F (43°C).
Malfunctions can occur at these temperatures.
• Refrigerator is designed for indoor household
application only.
• Use an appliance dolly when moving
refrigerator. ALWAYS truck refrigerator from its
side or back - NOT from its front.
• Cover outside finish of refrigerator during
transport by wrapping cabinet in blankets
or inserting padding between the refrigerator
and dolly.
• Secure refrigerator to dolly firmly with straps or
bungee cords. Thread straps through handles
when possible. DO NOT overtighten.
Overtightening restraints may dent or damage
outside finish.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Doors & Drawer Removal
Remove and Replace Handles
1. Using a 3/32"or 1/8” hex wrench, loosen the
two set screws located on the side of each
handle.
2. Pull the handle straight out from the door.
Make sure you keep the screws for reattaching
the handles.
Remove Doors and Hinges (cont.)
Water Supply Requirements
6. Remove the parts for the top hinge as shown in
Top Hinge graphic. Lift the left-hand side door
from the bottom hinge pin.
A cold water supply with water pressure of
between 35 and 120 psi (241 and 827 kPa) is
required to operate the water dispenser and ice
maker. If you have questions about your water
pressure, call a licensed, qualified plumber.
Note: Remove the hinge pin cover from the
bottom hinge pin and keep it for later use. See
Bottom Hinge graphic.
3. To replace the handles, reverse the directions.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply
coming out of a reverse osmosis system going to
the water inlet valve of the refrigerator needs to
be between 35 and 120 psi (241 and 827 kPa).
Remove Doors and Hinges
IMPORTANT: Remove food and any adjustable
door or utility bins from doors.
Top Hinges
A
B
C
TOOLS NEEDED: 5/16", 3/8", 1/4" hex-head
socket wrench, #2 Phillips screwdriver, and a flat-
blade screwdriver.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi (276 to 414 kPa).
D
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed until you are
ready to lift them free from the cabinet.
If the water pressure to the reverse osmosis
system is less than 40 to 60 psi (276 to 414 kPa):
A. Hinge Cover Screw
B. Top Hinge Cover
Note: Provide additional support for the
refrigerator door while the hinges are being
removed. DO NOT depend on the door gasket
magnets to hold the door in place while you
are working.
C. 5/16" Hex-Head Hinge Screws
• Check to see whether the sediment filter in the
reverse osmosis system is blocked. Replace the
filter if necessary.
• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
• If your refrigerator has a water filter, it may
further reduce the water pressure when used in
conjunction with a reverse osmosis system.
Remove the water filter.
D. Top Hinge
Bottom Hinges
3. Starting with the right-hand side door, remove
the parts for the top hinge as shown in Top
Hinge graphic. Lift the refrigerator door from
the bottom hinge pin.
A
B
C
If you have questions about your water pressure,
call a licensed, qualified plumber.
Note: Remove the hinge pin cover from the
bottom hinge pin and keep for later use. See
Bottom Hinge graphic.
A. Hinge Pin Cover
B. Bottom Hinge
C. Hinge Screws
4. Before removing the left-hand side door,
disconnect the wiring plug located on the top
of the top hinge by wedging a flat-blade
screwdriver or fingernail between the two
sections. See Wiring Plug graphic.
Wiring Plug
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Door & Drawer Removal (cont.)
Installation
Replace Doors and Hinges
Water Supply Requirements
Connect the Water Supply
IMPORTANT: If you turn the refrigerator on
before the water line is connected, turn the ice
maker OFF.
Drawer Front Removal
1. Assemble the parts for the top hinge as shown
Gather the required tools and parts before
starting installation. Read and follow the
instructions provided with any tools listed here.
in Top Hinge graphic. DO NOT tighten the
screws completely.
2. Replace the parts for the bottom hinge as
shown in Bottom Hinge graphic. Tighten
TOOLS NEEDED:
Connect to Water Line
A
screws. Replace the refrigerator door.
Note: Provide additional support for the
refrigerator door while the hinges are being
moved. DO NOT depend on the door gasket
• Flat-blade screwdriver
• 7/16" and 1/2" Open-end or two adjustable
wrenches
• 1/4" Nut driver
• 1/4" Drill bit
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest
faucet long enough to clear line of water.
3. Locate a 1/2" to 1-1/4" (12.7 mm to 31.8 mm)
vertical cold water pipe near the refrigerator.
A. Loosen 4 Door Bracket Screws
magnets to hold the door in place while you
are working.
• Cordless drill
3. Align the door so that the bottom of the
refrigerator door aligns evenly with the top of
the freezer drawer. Tighten all screws.
4. Reconnect the wiring plug on top of the left-
hand side refrigerator door.
IMPORTANT:
IMPORTANT:
• All installations must meet local plumbing code
requirements.
• DO NOT use a piercing-type or 3/16" (4.76
mm) saddle valve which reduces water flow and
clogs more easily.
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but drill on the top
side of the pipe, not the bottom. This will
help keep water away from the drill and
normal sediment from collecting in the valve.
5. Replace the top hinge covers.
• Use copper tubing and check for leaks. Install
copper tubing only in areas where the household
temperatures will remain above freezing.
4. Determine the length of copper tubing you
need. Measure from the connection on the rear
of the refrigerator to the water pipe. Add 7 ft
(2.1 m) to allow for cleaning. Use 1/4"
(6.35 mm) O.D. (outside diameter) copper
tubing. Be sure both ends of copper tubing are
cut square.
Remove and Replace Freezer Drawer
IMPORTANT: Two people may be required to
remove and replace the freezer drawer.
Remove Drawer Front
Drawer Front Replacement
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer
glides to the drawer front. See Drawer Front
Removal graphic.
5. Using a cordless drill, drill a 1/4" hole in the
cold water pipe you have selected.
A
B
Note: Loosen screws three to four turns. Keep
the screws in the drawer front.
3. Lift drawer front upward and off the screws.
See Drawer Front Removal graphic.
C
D
Replace Drawer Front
E
F
G
1. Slide the drawer glides out of the freezer
compartment. Insert the screws in the top of
the drawer front into the slots in the drawer
brackets. See Drawer Front Replacement
graphic.
A. Cold water pipe
B. Pipe clamp
E. Compression sleeve
F. Shutoff valve
C. Copper tubing
D. Compression nut
G. Packing nut
2. Pull the drawer brackets toward you to position
the two screws in the bottom of the drawer
front into the brackets. See Drawer Front
Replacement graphic.
3. Completely tighten the four screws.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Leveling/Adjusting the Door
Connect to Water Line (cont.)
To enhance the appearance and maintain performance, the refrigerator should be level.
To protect property and refrigerator from damage, observe the following:
• Protect vinyl or other flooring with cardboard, rugs, or other protective material.
• DO NOT use power tools when performing leveling procedure.
6. Fasten the shutoff valve to the cold water pipe
with the pipe clamp. Be sure the outlet end is
solidly in the 1/4" drilled hole in the water pipe
and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe
clamp screws slowly and evenly so washer
makes a watertight seal. DO NOT overtighten
or you may crush the copper tubing.
5. Using an adjustable wrench, hold the nut on
the plastic water line to keep it from moving.
Then, with a second wrench, turn the
compression nut on the copper tubing
counterclockwise to completely tighten.
DO NOT overtighten.
Materials Needed
• 1/4” hex head driver
• Carpenter’s level
A
B
7. Slip the compression sleeve and compression
nut on the copper tubing as shown. Insert the
end of the tubing into the outlet end squarely
as far as it will go. Screw compression nut onto
outlet end with adjustable wrench. DO NOT
overtighten.
Note: Complete any required panel installation and/or water supply connection before leveling.
Refrigerator should be in permanent location prior to leveling.
C
D
E
1
2
8. Place the free end of the tubing in a container
or sink, and turn ON the main water supply.
Flush the tubing until water is clear. Turn OFF
the shutoff valve on the water pipe.
A. “P” clamp
B. Plastic water line
C. Compression nut
D. Copper tubing
Connect to Refrigerator
6. Check connection by pulling on copper tubing.
Attach copper tubing to refrigerator cabinet
with a “P” clamp. Turn on water supply to
refrigerator and check for leaks. Correct any
leaks.
1. Create a service loop (minimum diameter of 2
ft. [61.0 cm]) with the copper tubing. Avoid
kinks when coiling the copper tubing.
2. Remove the plastic cap from water valve inlet
port. Place a compression nut and sleeve on
the copper tubing.
To raise the front of the refrigerator, turn the leveler foot
screw clockwise. Note: Having someone push against the
top of the refrigerator takes some weight off the leveler
foot screws.
Remove toe grille. Grasp firmly and pull outward
to unclip.
3. Insert the end of the copper tubing into the
water valve inlet port. Shape tubing slightly so
that the tubing feeds straight into the port to
avoid kinks.
4. Slide the compression nut over the sleeve and
screw into the water valve inlet port.
3
4
A
B
C
D
A. Plastic water tubing
B. Sleeve
C. Compression nut
D. Copper tubing
To lower the front of the refrigerator, turn the leveler foot
screw counterclockwise. Note: Having someone push
against the top of the refrigerator takes some weight off
the leveler foot. This makes it easier to turn the levelers.
It may take several turns of the leveler foot screw to
adjust the tilt of the refrigerator.
Replace toe grill. Align the toe grille mounting clips
with the lower cabinet slots. Push the toe grille firmly
until it snaps into place. Check for level.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Service & Registration
Complete the Installation
Final Steps
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
1. Plug into a grounded 3 prong outlet.
2. Return all removable parts to doors and drawer
and food to refrigerator and freezer.
Contact Viking Range Corporation, 1-888-845-4641, for the nearest service parts distributor in
your area or write to:
Note: Allow 24 hours to produce the first batch
of ice. Discard the first three batches of ice
produced. Allow three days to completely fill the
ice container.
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
The serial and model numbers for your refrigerator are located on the upper wall, behind the lighting.
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
Performance Checklist
h Plug-in refrigerator and verify operation.
Installer’s information:
h Connect water supply (if applicable).
• Verify icemaker bail arm is down.
• Verify dispenser operation
(if applicable).
Installer’s name:_____________________________
Installer’s company:__________________________
Date:_______________________________________
h Align/square door(s).
These installation instructions should remain with the refrigerator for future
reference.
h Verify drain pan properly installed and no leaks
on water connection.
h Remove internal packaging and labels and
wipe refrigerator down.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|