*Tip : The equipment will turn off when the
correct three digit code number has
been entered. You can verify that you
have selected the correct code by
pressing the [MUTE] button, the
equipment should turn On and Off.
STEP1 Press the [DEVICE] button (CBL, TV or
VCR) you wish to verify and the
[SELECT] button simultaneously for 3
second.
Introduction
The remote control is designed to operate
three devices, CBL(S/A Explorer and other
Cable boxes), TV, and VCR/DVD equipments.
Button Functions
1
3
Operating Instructions
For 3 Function
Cable Remote Control
*Tip : The LED will light on for 20 seconds.
The next step must be entered while
LED is on.
TV, VCR, CBL
MENU
*Note : If there is more than one three digit
number listed for your brand, try one
code number at a time until your
equipment turns off.
Allow you to turn on and off your
TV, VCR and CABLE Box.
Displays cable settings or Menu.
Replacing Batteries
Before you program or operate the remote
control, you must install two new AAA alkaline
batteries.
2
STEP2 Press the [INFO] button.
UR3-SR
INFO
The device LED will blink a number of times
indicating the number of each digit for the
code. Each digit is separated by a 1 second
interval of the LED being off.
Example : One blink, three blinks and eight
blinks with an interval of 1
second LED being off, indicates
the code number 138.
GUIDE
Displays channel and program
information.
Displays the program guide.
STEP4 Store the three digit code number by
pressing the same [DEVICE] button
once again. The device LED will blink
twice to confirm that the code has
been stored.
HELP
EXIT
Displays HELP screen.
STEP1 Remove the battery compartment cover
Exits settings, menus, and guides.
on the back of your remote control.
SELECT
Selects and deselects screen item.
CURSOR KEYS
*Note : Try all the functions on the remote
control. If any of the functions do
not work as they should, repeat from
Step 2 using the next three digit code
number from the same brand list.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
Moves through menus or guides.
A, B, C
Selects options in menus and IPG.
Note : Ten blinks is equal to the number 0.
VCR/DVD KEYS
D. Programming a second TV
MUTE
Perform standard VCR and DVD
functions when in VCR mode,
and Video On Demand functions
when in VOD mode.
STEP3 Replace the battery compartment
Turns volume off.
to VCR Mode.
cover.
B. Auto Search Method.
STEP1 Press the [DEVICE] button [VCR] to
be programmed and the [SELECT]
button simultaneously for 3
seconds.
VOL+/-
If none of the three digit code numbers
assigned to your brand turns off your
equipment or the code table does not list your
brand, you can use the Auto Search Method
to find the correct three digit code number for
your equipment by the following steps:
Adjusts the volume up and down.
Install two
AAA alkaline batteries
as shown here
CH+/-
Selects channels up or down.
LAST
Returns to last channel viewed.
*Tip : The LED will light on for 20 seconds.
The next step must be entered while
LED is on.
STEP1 Turn on the equipment you wish to
VCR/VOD
NUMBER KEYS
STEP2 Press the [TV] button to pick up the
Switches the VCR controls into
Video On Demand controls.
program. (CBL, TV, VCR or DVD)
Allow direct access to specific channels
and menu options.
TV code table.
STEP2 Press the [DEVICE] button (CBL, TV or
VCR) to be programmed and the
[SELECT] button simultaneously for 3
second. The device LED will turn on
indicating that it is ready to be
programmed.
STEP3 Point the remote control toward the
equipment and enter the three digit
code number assigned to your TV
brand from the code tables.
VOD
Access Video On Demand.
STEP4 Store the three digit code number by
pressing the [DEVICE] button (VCR)
once again. The device LED will blink
twice to confirm that the code has
been stored.
*Tip : The LED will light on for 20 seconds. The
next step must be entered while LED is
on.
STEP3 Press the [CH+] or [CH-] button one
step at a time. The remote will emit a
series of Power ON/OFF code signals.
Release the [CH+] or [CH-] button as
soon as the equipment turns off.
E. Programming For Advanced Function.
Operations
4
Programming the Remote Control.
5
In the CABLE device mode, the A,B,C and
VOD buttons can be programmed to act as
a macro button to send out up to 10
commands with one button press.
Default State:
A. Three Digit Code Method.
The remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three digit code numbers are listed in the code table of the instruction manual.
Device Default: Cable mode with S/A Explorer.
Volume Default: Vol +/- & Mute from TV mode.
*Tip :You can verify that you selected the
correct code by pressing the [MUTE]
button. The equipment should turn On
and Off.
STEP1 Press the [CBL] button to select the
CABLE mode.
VOD button:
STEP1 Turn on the equipment you wish to program. (CBL, TV, VCR or DVD)
STEP4 Press the same [DEVICE] button to
store the code. The Device LED will
blink twice to confirm that the code
has been stored.
STEP2 Press the [VOD] button and the
[SELECT] button simultaneously for
3 second. The CBL device LED will
turn on for 20 seconds.
This button sends out CH 999 with default and a
customer can program any commands, up to 10
commands. Please refer to section E for details.
STEP2 Press the [DEVICE] button (CBL, TV or VCR) to be programmed and the [SELECT] button
simultaneously for 3 second. The device LED will turn on indicating that it is ready to be
programmed.
Universal Remote Control, Inc.
*Tip : The LED will light on for 20 seconds. The next step must be entered while LED is on.
STEP3 Press up to 10 buttons you wish to
store. The CBL device LED will blink
once for each command entered.
C. To Find the Three Digit Code
Number That was Stored in
the Device.
STEP3 Point the remote control toward the equipment and enter the three digit code number
OCE-0009A Rev 01(11/21/02)
assigned to your brand from the code tables.
Download from Www.Somanuals.com. All Manuals Search And Download.
|