Toshiba Printer EM1 33033 User Manual

TEC Thermal Printer  
B-470-QQ SERIES  
Owner’s Manual  
Owner’s Manual  
Mode d’emploi  
Bedienungsanleitung  
Manual de instrucciones  
Gebruikershandleiding  
Table of Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
Safety Summary  
Safety Summary  
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions  
necessary for safe handling are included in this manual. All warnings and cautions contained in this  
manual should be read and understood before handling or maintaining the equipment.  
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified  
using the procedures described in this manual, turn off the power, unplug the machine, then contact your  
authorized TOSHIBA TEC representative for assistance.  
Meanings of Each Symbol  
This symbol indicates warning items (including cautions).  
Specific warning contents are drawn inside the symbol.  
(The symbol on the left indicates a general caution.)  
This symbol indicates prohibited actions (prohibited items).  
Specific prohibited contents are drawn inside or near the symbol.  
(The symbol on the left indicates “no disassembling”.)  
This symbol indicates actions which must be performed.  
Specific instructions are drawn inside or near the symbol.  
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)  
This indicates that there is the risk of death or serious injury if the  
machines are improperly handled contrary to this indication.  
WARNING  
specified AC voltage  
is prohibited.  
Any other than the  
Do not use voltages other than the  
voltage (AC) specified on the rating  
plate, as this may cause fire or  
electric shock.  
Do not plug in or unplug the power  
cord plug with wet hands as this may  
cause electric shock.  
Prohibited  
Prohibited  
Prohibited  
If the machines share the same  
outlet with any other electrical  
appliances which consume large  
amounts of power, the voltage will  
fluctuate widely each time these  
appliances operate. Be sure to  
provide an exclusive outlet for the  
machine as this may cause the  
machines to malfunction.  
Do not place metal objects or  
water-filled containers such as flower  
vases, flower pots or mugs, etc. on  
top of the machines. If metal objects  
or spilled liquid enter the machines,  
this may cause fire or electric  
shock.  
Prohibited  
Do not insert or drop metal,  
flammable or other foreign objects into  
the machines through the ventilation  
slits, as this may cause fire or electric  
shock.  
Do not scratch, damage or modify  
the power cords. Also, do not place  
heavy objects on, pull on, or exces-  
sively bend the cords, as this may  
cause fire or electrical shock.  
Prohibited  
Disconnect  
the plug.  
Continued use of the machines in an  
abnormal condition such as when the  
machines are producing smoke or  
strange smells may cause fire or elec-  
tric shock. In these cases, immedi-  
ately turn off the power switches and  
disconnect the power cord plugs from  
the outlet. Then, contact your author-  
ized TOSHIBA TEC representative for  
assistance.  
Disconnect  
the plug.  
If the machines are dropped or their  
cabinets damaged, first turn off the  
power switches and disconnect the  
power cord plugs from the outlet, and  
then contact your authorized  
TOSHIBA TEC representative for  
assistance. Continued use of the  
machine in that condition may cause  
fire or electric shock.  
(i)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
Safety Summary  
Disconnect  
the plug.  
Disconnect  
the plug.  
If foreign objects (metal fragments,  
water, liquids) enter the machines,  
first turn off the power switches and  
disconnect the power cord plugs from  
the outlet, and then contact your  
authorized TOSHIBA TEC repre-  
sentative for assistance. Continued  
use of the machine in that condition  
may cause fire or electric shock.  
When unplugging the power cords,  
be sure to hold and pull on the plug  
portion. Pulling on the cord portion  
may cut or expose the internal wires  
and cause fire or electric shock.  
Connect a  
grounding  
wire.  
No disassem-  
bling.  
Ensure that the equipment is  
properly grounded. Extension cables  
should also be grounded. Fire or  
electric shock could occur on  
mproperly grounded equipment.  
Do not remove covers, repair or  
modify the machine by yourself. You  
may be injured by high voltage, very  
hot parts or sharp edges inside the  
machine.  
This indicates that there is the risk of personal Injury or damage to  
CAUTIONobjects if the machines are improperly handled contrary to this indication.  
Precautions  
The following precautions will help to ensure that this machine will continue to function correctly.  
Try to avoid locations that have the following adverse conditions:  
*
*
Temperatures out of the specification  
Shared power source  
*
*
Direct sunlight  
Excessive vibration  
*
*
High humidity  
Dust/Gas  
The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild  
detergent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic  
covers.  
USE ONLY TOSHIBA TEC SPECIFIED paper and ribbons.  
DO NOT STORE the paper or ribbons where they might be exposed to direct sunlight, high tem-  
peratures, high humidity, dust, or gas.  
Ensure the printer is operated on a level surface.  
Any data stored in the memory of the printer could be lost during a printer fault.  
Try to avoid using this equipment on the same power supply as high voltage equipment or equip-  
ment likely to cause mains interference.  
Unplug the machine whenever you are working inside it or cleaning it.  
Keep your work environment static free.  
Do not place heavy objects on top of the machines, as these items may become unbalanced and fall  
causing injury.  
Do not block the ventilation slits of the machines, as this will cause heat to build up inside the  
machines and may cause fire.  
Do not lean against the machine. It may fall on you and could cause injury.  
Care must be taken not to injure yourself with the printer paper cutter.  
Unplug the machine when it is not used for a long period of time.  
Request Regarding Maintenance  
Utilize our maintenance services.  
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance  
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the  
machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid  
rainy seasons.  
Our preventive maintenance service performs the periodic checks and other work required to  
maintain the quality and performance of the machines, preventing accidents beforehand.  
For details, please consult your authorized TOSHIBA TEC representative for assistance.  
Using insecticides and other chemicals  
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or  
other parts to deteriorate or cause the paint to peel.  
(ii)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
TABLE OF CONTENTS  
Page  
1. INTRODUCTION.............................................................................. 1-1  
1.1 Applicable Model ..................................................................................... 1- 5  
1.2 Accessories ............................................................................................. 1- 5  
2. SPECIFICATIONS ........................................................................... 2-1  
2.1 Printer ...................................................................................................... 2- 1  
2.2 Options .................................................................................................... 2- 2  
2.3 Media....................................................................................................... 2- 3  
2.4 Ribbon ..................................................................................................... 2- 3  
3. OVERVIEW ...................................................................................... 3-1  
3.1 Front/Rear View....................................................................................... 3- 1  
3.2 Operation Panel ...................................................................................... 3- 1  
5. INSTALLING THE PRINTER ........................................................... 5-1  
6. LOADING THE MEDIA .................................................................... 6-1  
7. LOADING THE RIBBON ................................................................. 7-1  
8. INSERTING THE OPTIONAL FLASH MEMORY CARD................. 8-1  
9. CARE/HANDLING OF THE MEDIA AND RIBBON......................... 9-1  
10. GENERAL MAINTENANCE .......................................................... 10-1  
10.1 Cleaning ................................................................................................ 10- 1  
10.2 Covers and Panels ................................................................................ 10- 1  
10.3 Removing Jammed Paper ..................................................................... 10- 2  
10.4 Threshold Setting .................................................................................. 10- 4  
10.5 Auto Ribbon Saving Mode .................................................................... 10- 5  
11. TROUBLESHOOTING................................................................... 11-1  
CAUTION:  
1. This manual may not be copied in whole or in part without prior written permission of  
TOSHIBA TEC.  
2. The contents of this manual may be changed without notification.  
3. Please refer to your local Authorized Service representative with regard to any queries  
you may have in this manual.  
Copyright © 1999  
by TOSHIBA TEC CORPORATION  
All Rights Reserved  
570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
1. INTRODUCTION  
1.1 Applicable Model  
1. INTRODUCTION  
Thank you for choosing the TEC B-470 series thermal/transfer printer. This high performance printer is  
equipped with superior hardware including the specially developed (8 dots/mm, 203.2 dots/inch) near  
edge print head which will allow very clear print at a maximum speed of 254 mm/sec. (10 inches/sec.).  
The media supply is internal. Combined with the optional features including an automatic ribbon saver,  
rewinder/strip mechanism and external media supply, you will have a printer to suit a wide variety of  
applications and environments.  
This manual contains general set-up and maintenance information and should be read carefully to help  
gain maximum performance and life from your printer. For most queries please refer to this manual and  
keep it safe for future reference.  
1.1 Applicable Model  
B-472-QQ  
B-472-QQ-US  
Model name description  
B - 4 7 2 - Q Q  
Destination Code  
QQ: Canada, Mexico, etc.  
QQ-US: North America Block  
Thermal direct/Thermal transfer  
1.2 Accessories  
Owner's Manual  
(EM1-33003)  
Power Cord  
Unpacking Procedure  
Quality control report  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
2.1 Printer  
2. SPECIFICATIONS  
2. SPECIFICATIONS  
2.1 Printer  
Model  
Item  
B-470-QQ/QQ-US  
AC 100V ~ 120V +10%, -15%, 50Hz  
2.2A, 190W maximum (standby: 260mA, 18W)  
5°C ~ 40°C (41°F ~ 104°F)  
25% ~ 85%RH (no condensation)  
Thermal print head 8 dots per mm (203.2 dots per inch)  
Thermal direct or Thermal transfer  
Supply voltage  
Power consumption  
Operating temperature range  
Relative humidity  
Print head  
Printing methods  
Print speeds  
76.2 mm/sec. (3 inch/sec.), 152.4 mm/sec. (6 inch/sec.),  
254 mm/sec. (10 inch/sec.)  
104.0 mm (4.09 inches)  
Batch (Continuous), Strip (On-demand) and Cut modes  
Maximum print width  
Dispensing modes  
(Both cut and strip modes are available only when their respective  
modules are fitted.)  
16 characters x 1 line  
291 mm (width) x 460 mm (depth) x 308 mm (height)  
17 kg (without media and ribbon)  
Message display  
Dimensions  
Weight  
UPC-E, UPC-E+2digits, UPC-E+5digits  
UPC-A, UPC-A+2digits, UPC-A+5digits  
JAN8, JAN13, EAN8, EAN8+2digits, EAN8+5digits  
EAN13, EAN13+2digits, EAN13+5digits  
MSI, ITF, NW-7, CODE39, CODE93, CODE128, EAN128  
PDF417, DATA MATRIX, Industrial 2 to 5  
Times Roman (6 sizes), Helvetica (6 sizes), Presentation (1 size),  
Letter Gothic (1 size), Prestige Elite (2 sizes), Courier (2 sizes),  
OCR (2 types), Writable characters (40types), Outline font (1 type)  
0°, 90°, 180°, 270°  
Available bar code types  
Fonts  
Rotations  
Serial interface (RS-232C)  
Standard interface  
Parallel Interface (Centronics) (QQ-US)  
Expansion I/O interface  
Optional interfaces  
Flash memory card interface  
Parallel Interface (Centronics) (QQ)  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
2.2 Option  
2. SPECIFICATIONS  
2.2 Option  
Option Name  
Cutter module  
I/F PC board  
Type  
Source  
Usage  
B-4205-QM  
B-4700-IO-QM  
See NOTE 1.  
See NOTE 3.  
A stop and cut swing cutter  
I/F PC board is equipped with the flash  
memory card interface, Centronics inter-  
face and expansion I/O interface. To  
purchase the I/F PC board, please in-  
quire at your local distributor.  
Peel off module  
B-4905-H-QM  
See NOTE 1.  
This allows use of on-demand (peel-off)  
operationortorewindlabelsandbacking  
paper together when using the rewind  
guide plate. To purchase the strip mod-  
ule, please inquire at your local distribu-  
tor.  
Ribbon saving module  
B-4905-R-QM  
B-4905-FF-QM  
See NOTE 1.  
See NOTE 1.  
See NOTE 2.  
This allows use of ribbon save, reducing  
ribbon costs. To purchase the ribbon  
saving module, please contact your dis-  
tributor or TOSHIBA TEC HQ can assist  
in finding one for you.  
Thisisapaperguideexclusivelyusedfor  
fanfold paper.  
Attaching it in place of the standard pa-  
per guide allows the printer to print on  
fanfold paper.  
Fanfold paper guide  
module  
Flash memory card  
A flash ROM card (1MB and 4MB) for  
storing logos, writable characters and  
formats.  
NOTES:1. Available from your nearest TOSHIBA TEC representative or TOSHIBA TEC Head Quarters.  
2. When purchasing flash memory card locally, select one having the specifications described  
at page 8-1.  
3. The B-472-QQ-US model is provided with the I/F PC Board including only the Centronics  
Interface as standard. When the flash memory card interface or expansion I/O interface is  
required,itisnecessarytoexchangethisPCboardwiththeB-4700-IO-QM. Fordetails,please  
contact the nearest TOSHIBA TEC representative or TOSHIBA TEC Head Quarter.  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
2.3 Media  
2. SPECIFICATIONS  
2.3 Media  
Tag paper  
Label  
Refer to the following  
NOTE 2. Black Mark  
(on reverse side)  
Black Mark  
(on reverse side)  
I
I
Stop  
Stop  
position  
Tag paper  
position  
E
F
Cut  
position  
Cut  
position  
Reference  
coordinate  
Reference  
coordinate  
1
A
J
A
1
H
B
H
Reference  
coordinate  
Reference  
coordinate  
2
2
G
D
C
Feed direction  
G
C
Fig. 2-1  
[Unit : mm]  
Label dispensing mode  
Batch mode  
10.0 ~ 999.0  
Strip mode  
Cut mode  
Item  
A : Span of one label/tag  
25.4 ~ 999.0  
Label: 38 ~ 999.0  
Tag: 25.4 ~ 999.0  
25.0 ~ 993.0  
B : Label/tag length  
C : Width including backing paper  
D : Label width  
23.4 ~ 997.0  
50.8 ~ 112.0  
47.8 ~ 109.0  
2.0 ~ 20.0  
8.0 ~ 997.0  
2.0 ~ 20.0  
E : Gap length  
6.0 ~ 20.0  
F : Black mark length (Tag paper)  
G : Effective print width  
2.0 ~ 10.0  
10.0 ~ 104.0  
21.4 ~ 384.0  
21.4 ~ 896.0  
23.4 ~ 384.0  
23.4 ~ 896.0  
1.0  
H :  
Standard  
Max. memory  
Standard  
23.0 ~ 384.0  
23.0 ~ 896.0  
23.4 ~ 384.0  
23.4 ~ 896.0  
6.0 ~ 384.0  
6.0 ~ 896.0  
8.0 ~ 384.0  
8.0 ~ 896.0  
Effectice  
print length  
Label  
Tag  
Max. memory  
I
J
: Print speed up/slow down area  
: Black mark length (Label)  
Refer to the following NOTE 2.  
Maximum effective  
Standard  
192.0  
length for on the fly issue Max. memory  
Outer roll diameter  
448.0  
ø200 Max.  
0.13 ~ 0.17  
0.15 ~ 0.29  
Thickness  
Label  
Tag  
NOTES: 1. The media specification other than above are unchanged.  
2. When marking black marks on label rolls, the following requirements must be satisfied.  
When the gap length is less than 4 mm:  
The black mark length should be longer than the gap length.  
When the gap length is 4 mm or more:  
The black mark should not overlap the gap for more than 4 mm and the following label.  
2.4 Ribbon  
Type  
Width  
Length  
NOTES: 1. "On the fly issue" means that the printer can draw and print  
Spool type  
68mm~112mm  
600 m  
without stopping between labels.  
2. Toensureprintqualityandprintheadlifeuse onlyTOSHIBA  
TEC specified media and ribbons.  
3. When using the cutter ensure that label length B plus inter  
label gap length E exceeds 35 mm. (i.e. label pitch should  
be greater that 35 mm.)  
ø90 mm (max.)  
Outer diameter  
4. When rewinding the media onto the take-up spool in batch  
mode, the max. outer roll diameter should be 180 mm.  
5. Use of rough media for the ribbon saving issue may cause  
ribbon smudges.  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
3. OVERVIEW  
3.1 Front/Rear View  
3. OVERVIEW  
3.1 Front/Rear View  
Front View  
Rear View  
Top Cover  
Supply Window  
Message Display (LCD)  
Memory Card Slot  
(Option)  
Serial Interface  
Connector  
(RS-232C)  
Parallel I/F Connector  
(Centronics)  
Standard: QQ-US  
Option: QQ  
Operation Panel  
Media Outlet  
Expansion I/O  
Interface Connector  
(Option)  
Power Switch  
0: OFF  
1: ON  
AC Power Inlet  
Fig. 3-1  
3.2 Operation Panel  
MESSAGE DISPLAY (LCD)  
Displays messages in the language selected by DIP switch.  
When power is turned on and it is ready to print, "ON LINE" is  
displayed.  
POWER LED (Green)  
Lights when the power is turned on.  
ON-LINE LED (Green)  
1) Flashes when communicating with a host computer.  
2) On while printing.  
ERROR LED (Red)  
Lights when a communication error occurs, when the media/  
ribbon ends or the printer does not operate correctly.  
FEED key  
Feeds paper.  
RESTART key  
Fig. 3-2  
Resets the printer when paused or when an error occurs.  
Used to set the threshold. (Refer to page 10-4)  
PAUSE key  
Pauses printing.  
Message display shows "PAUSE" and an unprinted count.  
Used to set the threshold. (Refer to page 10-4)  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
4. DIP SWITCH FUNCTIONS  
4. DIP SWITCH FUNCTIONS  
4. DIP SWITCH FUNCTIONS  
The DIP switches are located to the right of the supply shaft.  
WARNING:  
Supply Shaft  
Ribbon Shaft  
Turn the POWER OFF before switching the functions.  
(1) DIP SW 1  
No.  
1
ON/OFF  
OFF  
ON  
Function  
Auto ribbon save function  
Without  
With  
Language to display LCD error message  
4
OFF  
2
3
2
3
OFF OFF  
English  
Fig. 4-1  
ON OFF OFF German  
OFF  
OFF  
OFF ON  
ON ON  
French  
Dutch  
OFF OFF ON  
Spanish  
Japanese  
Italian  
Not used  
Without  
With  
ON  
ON  
ON  
ON OFF  
OFF ON  
4
5
6
7
8
ON  
ON  
OFF  
ON  
Auto media feed after a cut issue (See  
page 6-5)  
Use of the built-in rewinder/Head up  
function in cut mode Refer to Note 2.  
OFF  
ON  
OFF  
ON  
OFF  
ON  
Without  
With  
Must be set to OFF.  
Must be set to OFF.  
(2) DIP SW 2  
No.  
ON/OFF  
Function  
1
2
Transmission speed  
1
2400 BPS  
4800 BPS  
9600 BPS  
19200 BPS  
1 bit  
2 bit  
7 bit  
8 bit  
without  
with  
EVEN  
ODD  
OFF OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
2
3
4
5
6
OFF  
Stop bit length  
Data length  
ON  
OFF  
ON  
OFF  
ON  
Parity check  
OFF  
ON  
Parity check (effective when  
DIP SW #5 is set to ON.)  
Data protocol  
8
7
XON/XOFF  
(No XON is output at the power on time.)  
(No XOFF is output at the power off time.)  
READY/BUSY (DTR)  
(No XON is output at the power on time.)  
(No XOFF is output at the power off time.)  
READY/BUSY (RTS)  
OFF  
OFF  
7
8
OFF  
ON  
(XON is output at the power on time.)  
(XOFF is output at the power off time.)  
XON/XOFF + READY/BUSY  
(XON is output at the power on time.)  
(XOFF is output at the power off time.)  
XON/XOFF  
ON  
OFF  
(XON is output at the power on time.)  
(XOFF is output at the power off time.)  
ON  
ON  
NOTES: 1. The shaded settings are the factory default settings. "OFF" means "OPEN".  
2. The Dip switch #1-6 functions in accordance with equipment to be used.  
3. If you would like to switch to READY/BUSY (DTR) or to READY/BUSY (RTS) of data protocol, please  
contact your authorized TOSHIBA TEC representative.  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
EM1-33033  
5. INSTALLING THE PRINTER  
5. INSTALLING THE PRINTER  
5. INSTALLING THE PRINTER  
WARNING!  
Turn the POWER SWITCH to OFF before connecting the power cord or cables.  
Serial I/F Cable (RS-232C)  
Expansion I/O Cable (Option)  
Parallel I/F Cable  
(Centronics)  
Standard: QQ-US  
Option: QQ  
Fig. 5-1  
Power Cord  
NOTE: Only the power cord is provided with this product. If using another cable, it should conform to  
the following specifications. For more details, please contact your local TOSHIBA TEC  
service representative.  
Centronics Interface (36 pins, Male)  
Printer-Side Connector Pin Signals  
RS-232C Interface  
Expansion I/O Interface (24 pins, Male)  
Printer-Side Connector Pin Signals  
DB-25S (25 pins, Male,  
Metric screw type)  
DB-9P  
Connector to PC  
Connector to Printer  
PIN No.  
Signal  
Shield  
RXD  
TXD  
CTS  
RTS  
DTR  
GND  
DSR  
PIN No.  
Signal  
N.C.  
RXD  
TXD  
DTR  
GND  
DSR  
RTS  
CTS  
N.C.  
1
2
3
4
5
6
7
20  
1
2
3
4
5
6
7
8
9
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
WARNING:  
1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn  
into the moving parts, push the switch in the “OFF” position to stop movement.  
2. To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.  
The printer prints both labels and tags.  
1. Turn off the power and open the top cover.  
2. Turn the head lever to position 3, then release the ribbon shaft holder plate.  
Top Cover  
Ribbon Shaft Holder Plate  
Head Lever  
Fig. 6-1  
NOTES: 1.When the head lever is turned to position 2, the print head is raised.  
2.When the head lever is turned to position 3, the print head and the pinch roller are raised.  
3.To allow printing the head lever must be set to position 1. (This ensures that the print head  
and the pinch roller are closed.)  
3. Turn the locking ring counter clockwise and remove the supply holder from the supply shaft.  
NOTE: Donotturntheforcethelockingringtoofarcounterclockwiseoritmaycomeoffthesupplyholder.  
Supply Shaft  
Locking Ring  
Supply Holder  
Fig. 6-2  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
4. Put the media on the supply shaft.  
5. Pass the media around the damper, then pull the media towards the front of the printer.  
6. Insert the ridge of the supply holder into the groove of the supply shaft until the media is fixed. Then turn  
the locking ring clockwise to secure the supply holder. This will centre the media automatically.  
NOTE: Do not over tighten the locking ring of the supply holder.  
Groove Ridge  
Projection  
Damper  
Supply Holder  
Media  
Supply Shaft  
Fig. 6-3  
7. Insert the media into the paper holders of the media guide, adjust the media guides to the media width,  
and tighten the locking screw.  
8. Check that the media path through the printer is straight. The media should be centered under the print  
head.  
Media Guide  
Supply Holder  
Media Guide  
Media  
Paper Holder  
Print Head  
Media  
Paper Holder  
Locking Screw  
Fig. 6-4  
NOTE: When using the label rolled with labels facing outside, please remove the upper plates of both  
paper holders using the following procedure. Failure to do this may cause a paper jam error.  
If you have any questions, please contact your nearest TOSHIBA TEC service representative.  
6-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
Removing the paper holders' upper plates from the media guide  
1 Remove the two T-4x8 screws to detach the media guide from the printer.  
Media Guide  
Screw (T-4x8)  
Fig. 6-5  
2 RemovetheSM-3x6screwortheSM-3x8screwtodetachthepaperholders'upperplates from  
the media guide.  
(Right)  
(Left)  
Screw (SM-3x8)  
Paper Holder  
Screw (SM-3x6)  
Paper Holder  
Fig. 6-6  
3 Attach the media guide back in position.  
NOTE: Donotlosetheremovedupperplatesbecausetheyarerequiredwhenusingthelabelrolled  
with labels facing inside.  
9. Set the black mark/feed gap sensor to the correct position by turning the adjusting knob. Turning the  
knob right will move the sensor towards the center of the media while turning left will move it away from  
the center of the media.  
6-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
An easy way to set the black mark sensor position  
1 Pull the media about 500 mm out of the front of the printer, turn the media back on it's self and  
feed it under the print head past the sensor so that the black mark can be seen from above.  
2 Adjust the sensor position to that of the black mark (the upper hole indicates the position of the  
black mark sensor).  
Black Mark Sensor  
Black Mark  
Media  
(Feed Gap Sensor)  
Adjusting Knob  
Fig. 6-7  
NOTE: Make sure to set the sensor to detect the center of the black mark, otherwise a paper jam  
error could occur.  
Setting the feed gap sensor position  
1 Adjust the sensor to detect on the gap (the lower hole indicates the position of the feed gap  
sensor.)  
(Black Mark Sensor)  
Backing Paper  
Media  
Media  
Feed Gap Sensor  
Adjusting Knob  
Fig. 6-8  
6-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
10. The media is now loaded and the sensor position is set.  
Batch type:  
Media  
Fig. 6-9  
NOTE: Set the selection switch to the STANDARD/STRIP position. Improper setting can affect the print  
quality.  
Strip type:  
1 Remove enough labels from the leading edge media to leave 500 mm of backing paper  
exposed.  
2 Wind the backing paper onto the take-up spool and fix in position with the take-up clip.  
(Wind the paper counter clockwise around the spool as this is the direction it rotates.)  
3 Rotate the take-up spool anti-clockwise a few times to take up any slack in the backing paper.  
Media  
Take-up Spool  
Front Plate  
Black Screw  
Take-up Clip  
(HAA-0004001)  
Backing Paper  
Fig. 6-10  
NOTES: 1. The backing paper is easier to feed back to the take-up spool if the front plate is removed.  
2. When fitting the tace-up clip the longer side of the clip should be fitted into the shallow groove  
on the take-up spool.  
3. When printer at a speed of 10"/sec., strip function is unavailable.  
4. Set the selection switch to the STANDARD/STRIP position.  
6-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
6. LOADING THE MEDIA  
6. LOADING THE MEDIA  
Cutter type: Where a cutter is fitted load the media as standard and feed it through the cutter module.  
NOTES: 1. Besuretocutthebackingpaperoflabel. Cuttinglabelswillcausethegluetosticktothecutter,  
which may affect the cutter quality and shorten the life.  
2. If the top edge of label winds onto the platen in cut issue, set the DIP SW 1-5 to ON.  
3. For the cutter type, the selection switch can be set to either position.  
Media Outlet  
Media  
Cutter Module  
Fig. 6-11  
Built-in rewinder type:  
1 Remove two black screws and front plate.  
2 Fit the rewinder guide plate to the strip shaft, then attach it with the sems screws.  
Tear-off Bar  
Rewinder Guide Plate  
(FMBD0034501)  
SM-4x6B Sems Screw  
SM-4x6B Sems Screw  
Adjustment Knob  
SM-4x8 Sems Screw  
Fig. 6-12  
NOTES: Set the selection switch to the REWINDER position.  
3 Follow the procedure for strip type.  
4 Adjustment  
If the label skews when using built-in rewinder unit, turn the adjustment knob of the rewinder  
guide plate to correct the label feed. Clockwise turn moves the rewinder guide plate forward  
and counterclockwise moves it backward.  
* When labels skew to the right:  
Loosen the SM-4x8 sems screw with a philips-head screw driver. Turn the adjustment knob  
clockwise, and tighten the SM-4x8 screw when the rewinder guide plate is positioned  
correctly.  
* When labels skew to the left:  
Loosen the SM-4x8 screw with a phillips-head screw driver. Turn the adjustment knob  
counterclockwise, and tighten the SM-4x8 screw when the rewinder guide plate is posi-  
tioned correctly.  
6-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
7. LOADING THE RIBBON  
7. LOADING THE RIBBON  
7. LOADING THE RIBBON  
WARNING!  
1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn  
into the moving parts, push the switch in the “OFF” position to stop movement.  
2. To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.  
There are two types of media available for printing on, these are standard media and direct thermal media  
(a chemically treated surface). DO NOT LOAD a ribbon when using a direct thermal media.  
1. When using a narrow width ribbon, slide the ribbon stoppers along the shafts to a position where the  
ribbon will be centered when it is fitted. When changing from a narrow width to a wider one rotate the  
ribbon stoppers by 90°, push them back to the correct position and then rotate back to lock.  
NOTE: When attaching the ribbon stoppers, fit them to the shafts with the pinchers facing into the printer.  
Ribbon Stopper  
(FMHC0010501)  
Ribbon Stopper  
(FMHC0010501)  
Fig. 7-1  
2. Leaving plenty of slack between the spools, fit the ribbon as shown below. When the ribbon is fitted it  
must be positioned over the ribbon sensor.  
3. Wind both shafts towards each other to tighten the ribbon.  
Ribbon Sensor  
Ribbon Shafts  
Ribbon  
Ribbon  
Fig. 7-2  
4. Reset the ribbon shaft holder plate by aligning it with the ribbon shaft.  
5. Turn the head lever clockwise to lower the print head.  
6. Close the top cover.  
7-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
8. INSERTING THE OPTIONAL FLASH MEMORY CARD  
8. INSERTING THE OPTIONAL FLASH MEMORY CARD  
8. INSERTING THE OPTIONAL FLASH MEMORY CARD  
WARNING!  
Turn the power OFF when inserting or removing the flash memory card.  
CAUTION:  
To protect memory cards, discharge static electricity from your body by touching the printer rear  
cover prior touching the memory cards.  
1. Turn the power off.  
2. Insert the flash memory card into the memory card slot on the rear of the printer.  
3. Turn the power on.  
Flash Memory Card  
Fig. 8-1  
NOTES: 1. Be sure to protect a flash memory card when not in use in the printer by putting it in it's  
protective cover.  
2. Do not subject the card to any shocks or excessive forces.  
3. Do not expose the card to extremes of heat by either storing in direct sunlight or close to a  
heater.  
4. Donotexposethecardtoexcessivehumiditybywipingitwithawetclothorstoringitinadamp  
place.  
5. Before inserting or removing the card, make sure that the power switch is turned off.  
6. Thefollowingflashcardscanbeused. (The1MB-cardisreadonlyandthe4MBcardcanread/  
write.)  
Maker code  
1CH  
Capacity  
Maker  
Type  
Device code  
D0H  
1M Byte Maxell  
EF-1M-TB AA  
MF81M1-GBDAT01  
EF-4M-TB CC  
EF-4M-TB DC  
FL04M-15-11119-03  
IMC004FLSA  
Mitsubishi  
B0H  
04H  
01H  
89H  
4M Byte Maxell  
Maxell  
88H  
ADH  
Centennial Technologies INC.  
INTEL  
A2H  
Simple TECHNOLOGY  
Mitsubishi  
STI-FL/4A  
MF84M1-G7DAT01  
FJN-004M6C  
PC Card KING MAX  
Centennial Technologies INC.  
PC Card  
FL04M-20-11138-67  
FJP-004M6R  
89H  
A0H  
AAH  
Mitsubishi  
MF84M1-GMCAV01  
8-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
9. CARE/HANDLING OF THE MEDIA AND RIBBON  
9. CARE/HANDLING OF THE MEDIA AND RIBBON  
9. CARE/HANDLING OF THE MEDIA AND RIBBON  
CAUTION:  
Be sure to read carefully and understand the Supply Manual. Use only media and ribbon  
which meet specified requirements. Use of non-specified media and ribbon may shorten the  
headlifeandresultinproblemswithbarcodereadabilityorprintquality. Allmediaandribbon  
should be handled with care to avoid any damage to the media, ribbon or printer. Read the  
following guideline carefully.  
• Do not store the media and ribbon for longer than the manufactures recommended shelf life.  
• Store media rolls on the flat end, do not store them on the curved sides as this might flatten that side  
causing erratic media advance and poor print quality.  
• Store the media in plastic bags and always reseal after opening. Unprotected media can get dirty and  
the extra abrasion from the dust and dirt particles will shorten the print head life.  
• Store the media and ribbon in a cool, dry place. Avoid areas where they would be exposed to direct  
sunlight, high temperature, high humidity, dust or gas.  
• The thermal paper used for direct thermal printing must not have the specifications which exceed Na+  
800 ppm, K+ 250 ppm and CL- 500 ppm.  
• Some ink used on pre-printed labels may contain ingredients which shorten the print head's product life.  
Do not use labels pre-printed with ink which contain hard substances such as carbonic calcium (CaCO3)  
and kaolin (Al2O3, 2SiO2, 2H2O).  
For further information please contact your local distributor or your media and ribbon manufacturer.  
9-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
10. GENERAL MAINTENANCE  
10.1 Cleaning  
10. GENERAL MAINTENANCE  
WARNING!  
1. Be careful when handling the print head as it becomes very hot.  
2. Care must be taken not to injure yourself with the printer paper cutter.  
3. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn  
into the moving parts, push the switch in the “OFF” position to stop movement.  
4. To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.  
10.1 Cleaning  
To help retain the high quality and performance of your printer it should be regularly cleaned. The  
greatertheusageoftheprinter, themorefrequentthecleaning. (i.e. lowusage=weekly:highusage=daily).  
A print head cleaner is not enclosed with the printer, so please inquire at your local distributor.  
1. Turn the power off.  
2. Open the top cover.  
3. Turn the head lever to raise the print head.  
4. Remove the ribbon and media.  
5. Clean the element of print head with print head cleaner.  
6. Wipe the platen, feed roller and pinch roller with a cleaner moistened with alcohol.  
Remove dust or foreign substances from the internal part of the printer, if any.  
Element  
Pinch Roller  
Print Head  
Print Head  
Feed Roller  
Element  
Platen  
Print Head Cleaner  
(24089500013)  
Fig. 10-1  
WARNING!  
1. Be sure to disconnect the power cord prior ot performing any maintenance.  
2. Do not use any tool that may damage the print head.  
3. DO NOT POUR WATER directly onto the printer.  
10-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
10. GENERAL MAINTENANCE  
10.3 Removing Jammed Paper  
10.2 Covers and Panels  
The covers should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent  
solution.  
NOTE: Clean the printer cover with an electrostatic free cleaner for automated office equipment.  
WARNING!  
1. DO NOT POUR WATER directly onto the printer.  
2. DO NOT APPLY cleaner or detergent directly onto any cover or panel.  
3. NEVER USE THINNER OR OTHER VOLATILE SOLVENT on the plastic covers.  
4. DO NOT clean the panel covers or the supply window with alcohol as it may cause them to  
discolor, loose their shape or develop structural weakness.  
10.3 Removing Jammed Paper  
1. Turn the power off.  
2. Open the top cover.  
3. Turn the head lever to position 3, then release the ribbon shaft holder plate.  
4. Remove the black screw to detach the media guide plate. (See Fig. 10-2.)  
5. Remove the ribbon and media.  
6. Remove the jammed paper. DO NOT USE any sharp implement or tool as these could damage the  
printer.  
7. Clean the print head and platen, then remove any further dust or foreign substances.  
8. Place the portion B of the media guide plate on the media sensor. Secure the media guide plate with  
the black screw.  
Media Sensor  
Media Guide Plate  
Black Screw  
(HAA-0004001)  
Fig. 10-2  
9. Paper jams in the cutter unit can be caused by wear or residual glue from label stock on the cutter. Do  
notusenonespecifiedmediainthecutter. IfyougetfrequentjamsinthecuttercontactyourAuthorized  
Service representative.  
10-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
10. GENERAL MAINTENANCE  
10.3 Removing Jammed Paper  
Cleaning the Cutter Unit  
WARNING!  
1. Be sure to turn the power off before cleaning the cutter unit.  
2. The cutters are sharp and care should be taken not to injure yourself when cleaning.  
1. Loosen two screws and remove the cutter cover.  
2. Remove the white screw and media guide.  
3. Remove the jammed paper and trash.  
4. Clean the cutter with dry cloth.  
Fixed Cutter  
Media Guide  
Screw  
White Screw  
(24741710304)  
Cutter Cover  
Cutter Unit  
Swing Cutter  
Fig. 10-3  
5. Assembling is reverse order of removal.  
10-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
10. GENERAL MAINTENANCE  
10.4 Threshold Setting  
10.4 Threshold Setting  
For the printer to maintain a constant print position it uses the transmissive sensor to detect the gap  
between labels by measuring the amount of light passing through the media. When the media is pre-  
printed, the darker (or more dense) inks can interfere with this process causing paper jam errors. To get  
around this problem a minimum threshold can be set for the sensor in the following way.  
Threshold setting procedure (For firmware version 2.5A or later)  
Power on  
(1) The printer is in stand-by.  
(2) Load a media roll in the usual way.  
(3) Press the [PAUSE] key.  
O N L I N E  
P A U S E  
[PAUSE] key.  
(4) The printer enters the pause mode.  
(5) Press and hold the [PAUSE] key for at least 3  
seconds in the pause state.  
[PAUSE] key.  
(6) The sensor type is displayed.  
T R A N S M I S S VE  
I
(7) Press the [FEED] key.  
[FEED] key.  
(8) Thereflectivesensor(blackmarksensor)isselected.  
(9) Press the [FEED] key again.  
R E F L E C T I  
V
E
[FEED] key.  
(10) Thetransmissivesensor(feedgapsensor)isselected.  
(11) Press and hold the [PAUSE] key.  
(12) The media is advanced until the [PAUSE] key is  
released.  
(13) Release the [PAUSE]key when more than 1.5 labels  
(tags) are advanced.  
T R A N S M I S S VE  
I
[PAUSE] key.  
T R A N S M I S S V  
E
I
(Threshold setting is completed by this operation.)  
P A U S E  
(14) Press the [RESTART] key.  
[RESTART] key.  
(15) The printer is in stand-by.  
O N L I N E  
O N L I N E  
Command  
(16) Send an issue command from the PC to the printer.  
NOTES:  
1. If the [PAUSE] key is released within 3 seconds whilst in pause state, paper will not feed.  
2. Failure to feed more than 1.5 to 2 labels may result in an incorrect threshold setting.  
3. While the print head is raised, the [PAUSE] key does not work.  
4. Error such as paper end and cutter error are not detected during paper feed.  
5. Selecting the transmissive sensor (for pre-printed labels) within software commands allows the printer to  
detect the proper print start position correctly even when using pre-printed labels.  
6. If the printer continues to print out of position after setting the threshold, adjust the feed gap sensor in the  
system mode. Reset the threshold again. Make sure that the transmissive sensor (for pre-printed labels) is  
selected in the feed and issue commands.  
10-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
10. GENERAL MAINTENANCE  
10.4 Threshold Setting  
Threshold setting procedure (For firmware version 2.5 or earlier)  
1 Turn the power on.  
2 Load the pre-printed label. (Any position)  
3 Press the [PAUSE] key once.  
4 Hold down the [PAUSE] key for more than 3 seconds and it will begin to feed. After it has fed the 2 label,  
release the [PAUSE] key.  
5 Press the [RESTART] key for ON LINE mode.  
6 Threshold setting is now completed.  
NOTES: 1. If the [PAUSE] key is not held down for more than 3 seconds in PAUSE mode the threshold  
will not be set.  
2. Ifthe[PAUSE]keyisreleasedbefore2labelshavebeenissuedthesettingmaynotbecorrect  
and will have to be re-set.  
10.5 Auto Ribbon Saving Mode  
Auto ribbon saving function is activated when it is selected by DIP switch (Refer to page 4-1) and no  
print area extends more than 20 mm.  
NOTE: According to the relation between the outer diameter of rewound ribbon and print speed,  
ribbon loss per saving varies as follows:  
Print speed  
3"/sec.  
6"/sec.  
10"/sec.  
Ribbon loss  
Approx. 6 mm  
Approx. 10 mm  
Approx. 20 mm  
10-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
11. TROUBLESHOOTING  
11. TROUBLESHOOTING  
11. TROUBLESHOOTING  
WARNING!  
If you cannot solve a problem with the following solutions, do not attempt to repair it yourself. Turn  
the power off, unplug the printer, then contact your Authorized Service representative for assis-  
tance.  
Problem  
Solution  
Error Message  
PAPER JAM  
****  
1. The media is not fitted correctly.  
1. Re-fit the media correctly.  
Press the [RESTART] key.  
2. Remove the cause of the jam and  
replace the media correctly.  
Press the [RESTART] key.  
3. Turn the power off then on again.  
Select the correct sensor.  
2. The media path is jammed and  
does not feed smoothly.  
3. The installed media type does not  
match the selected sensor.  
Feed the media.  
4. Adjust the sensor position.  
Press the [RESTART] key.  
4. The black mark position on the  
media does not match the sensor  
position.  
5. Turn the power off then on again.  
Set the correct media size.  
Feed the media.  
5. The installed media size is different  
from the programmed size.  
6. The feed gap sensor cannot see  
the difference between the print  
area and the gap.  
6. Set the threshold (see page 10-4).  
Else  
Turn the power off and call your  
Authorized Service representative.  
HEAD OPEN  
****  
Feed or printing has been attempted  
while the print head is raised.  
Lower the print head.  
Press the [RESTART] key.  
NO PAPER  
****  
The media has run out.  
The ribbon has run out.  
Load new media.  
Press the [RESTART] key.  
NO RIBBON  
****  
Load a new ribbon.  
Press the [RESTART] key.  
REWIND FULL  
****  
Too much backing paper or media is  
wound on the internal take-up spool.  
Remove the backing paper or media  
from the internal take-up spool.  
Then press the [RESTART] key.  
EXCESS HEAD  
TEMP  
The print head is too hot.  
Turn the power off and decrease the  
print head temperature.  
RIBBON ERROR  
****  
There is a fault with the ribbon sensor. Turn the power off. Contact your Au-  
thorized Service representative.  
11-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
11. TROUBLESHOOTING  
Error Message  
11. TROUBLESHOOTING  
Problem  
Solution  
Media is jammed in the cutter.  
CUTTER ERROR  
****  
Remove the jammed media and feed  
the undamaged media through the  
cutter.  
Press the [RESTART] key.  
Else  
Turn the power off and contact your  
Authorized Service representative.  
An error has occurred when loading  
data onto a flash memory card.  
FLASH WRITE  
ERR.  
1. Turn the power off, re-seat the flash  
memory card and try again.  
2. Replace the flash memory card and  
retry.  
3. Turn the power off and contact your  
Authorized Service representative.  
An error has occurred while formatting  
a flash memory card.  
FORMAT ER-  
ROR  
1. Turn the power off, re-seat the flash  
memory card and try again.  
2. Replace the flash memory card and  
retry.  
3. Turn the power off and contact your  
Authorized Service representative.  
No more data can be saved in the  
flash memory card.  
FLASH CARD  
FULL  
Replace the card with a new one and  
re-send data.  
(Only 1MB and 4MB cards can be  
used.)  
A communication error has occurred  
with the host.  
COMMS ERROR  
Turn the power off then on again or  
press the [RESTART] key.  
Check the program data.  
Call your Authorized Service repre-  
sentative if necessary.  
When an error is detected in a com-  
mand 20 bytes of the command are  
displayed.  
example)  
PC001; 0A00,  
Correct the command and re-send it  
again.  
(ESC, LF, NUL are not displayed.)  
Command error  
0300, 2, 2  
Hardware or software trouble.  
Other Error  
Message  
Turn the power off then on again. If the  
problem still exists turn the power off  
and contact your Authorized Service  
representative.  
NOTE: If an error is not cleared by pressing the [RESTART] key, the power must be switched off then  
on again.  
After the power has been switched off and on, all print data in the printer is cleared.  
**** denotes a remaining count of unprinted labels.  
11-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EM1-33033  
11. TROUBLESHOOTING  
11. TROUBLESHOOTING  
Problem  
Solution  
No print.  
1. Check that media and the ribbon is loaded correctly.  
2. Check whether the print head is set correctly or not.  
3. Check the cabling between the printer and the host.  
Dots missing in the print.  
Dirty print head. Clean the print head.  
Call your Authorized Service representative if necessary.  
Unclear (or blurred) printing.  
1. Dirty print head. Clean the print head.  
2. Bad or faulty ribbon. Replace ribbon.  
3. Poor media quality. Change media type.  
Power does not come on.  
1. Plug power cord into an AC socket.  
2. Check the circuit breakers or fuses.  
3. Plug another appliance into the AC socket to check if  
there is power supplied.  
Call your Authorized Service representative if necessary.  
Printer does not cut.  
Check for a paper jam in the cutter.  
Call your Authorized Service representative if necessary.  
You see a raised nap where the media  
has been cut.  
1. Clean the cutter blades.  
2. The blades are worn.  
Call your Authorized Service representative.  
11-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRINTED IN JAPAN  
EM1-33033  
E
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tech Craft TV Video Accessories MC6032B User Manual
Toshiba Cash Register MA 1190 User Manual
Toshiba VCR W 706 User Manual
TP Link Network Router TD W8901G User Manual
Tricity Bendix Clothes Dryer TM 310 W User Manual
Uniden Cordless Telephone TRU9585 User Manual
UVPS Welding System B003 001 User Manual
Vermont Casting Griddle VCS4017 User Manual
ViewSonic Camcorder VS13782 User Manual
Watlow Electric Network Card Series 97 User Manual