Toshiba DVR C DR0101 User Manual

INSTRUCTION MANUAL

1CH DIGITAL VIDEO RECORDER C-DR0100

(

)

NTSC SYSTEM

C-DR0101

C-DR0105

OUTPUT

VIDEO AUDIO

TIMER

REC

REVERSE

PLA

FRAME

SELECT

BLOCK

BUZZER

DISK FULL/

AILURE

ALARM

RESET

DIGIT

VIDEO RECORDER

Please follow the instructions in this manual to obtain the optimum results from this unit. We also

recommend that you keep this manual handy for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

8. DIGITAL VIDEO RECORDER ACTIVATION AND TERMINATION

8.1. Recorder’s Activation ....................................................................................... 27

8.2. When the Failure Screen Is Displayed ............................................................. 28

8.3. Recorder’s Termination .................................................................................... 28

9. OPERATION AFTER POWER FAILURE RESTORATION

9.1. When the Power Fails during Recording ......................................................... 28

10. RECORDING

10.1. Type of Recording .......................................................................................... 29

10.1.1. Recording Priorities ............................................................................ 29

10.2. Screen Display During Recording .................................................................. 29

10.3. The Keys to Be Used in Recording ................................................................ 31

10.4. Performing General Recording ...................................................................... 31

10.5. Performing Internal Timer Recording ............................................................. 31

10.6. Performing Alarm Recording .......................................................................... 32

11. PLAYBACK

11.1. Type of Playback ........................................................................................... 33

11.2. Screen Display During Playback .................................................................... 33

11.3. The Keys to Be Used in Playback .................................................................. 34

11.4. Performing Playback ...................................................................................... 34

11.5. Performing Various Playback Functions

11.5.1. Reverse Playback .............................................................................. 34

11.5.2. Fast Forward Playback And Fast Reverse Playback ......................... 34

11.5.3. Playback Pause (Still Picture) ............................................................ 34

11.5.4. Forward Frame Playback And Reverse Frame Playback .................. 35

11.5.5. Forward Block Playback And Reverse Block Playback ..................... 35

11.6. About the Playback Start Position .................................................................. 36

FUNCTIONS

12. SEARCH FUNCTIONS

12.1. The Keys to Be Used in Searching ................................................................ 37

12.2. Date/Time and Block Searches ..................................................................... 37

12.2.1. Basic Date/Time and Block Search Operations ................................. 37

12.2.2. Date/Time Search Operation ............................................................. 37

12.2.3. Block Search Operation ..................................................................... 38

12.3. Time Shift Search .......................................................................................... 39

CONNECTIONS

13. CONNECTIONS

13.1. Preparations for Connections ........................................................................ 40

13.1.1. Control Input/Output Terminal Connections ....................................... 40

13.2. When Using the 24 V AC or 12 V DC or AC Mains Camera .......................... 40

13.3. Connection to The Monitor TV ....................................................................... 40

13.4. Combination With The Digital Video Recorder/Multi-switchers

(C-MS91D, C-MS161D) ................................................................................. 41

13.4.1. Basic System ..................................................................................... 41

13.4.2. Expansion System (Series Recording) .............................................. 41

Download from Www.Somanuals.com. All Manuals Search And Download.

14. CONNECTION EXAMPLES

14.1. Connection to the 24 V AC or 12 V DC or AC Mains Camera ....................... 42

14.2. Connection to the Multi-switcher

14.2.1. Basic System

(Combined Example with the C-MS91D, Multi-switcher) ................... 43

14.2.2. Expansion System

(Combined Example with the C-MS91D, Multi-switcher) ................... 44

ADDITIONAL INFORMATION

15. RECORDING TIME TABLE

15.1. Recording Picture Quality Setting .................................................................. 45

15.2. When using the C-DR0100 ............................................................................ 45

15.3. When using the C-DR0101 ............................................................................ 45

15.4. When using the C-DR0105 ............................................................................ 46

16. EXTERNAL TERMINAL SPECIFICATIONS

16.1. RS-232C Communication Specifications ....................................................... 47

16.1.1. The Rules of Overall Communications .............................................. 47

16.1.2. Communication Protocol .................................................................... 47

16.1.3. RS-232C Connector Pin Assignment ................................................. 47

16.1.4. RS-232C Communication Format

(Controller to Digital Video Recorder) ................................................ 48

16.1.5. RS-232C Communication Command

(Controller to Digital Video Recorder) ................................................ 48

16.1.6. RS-232C Communication Format

(Digital Video Recorder to Controller) ................................................ 51

16.1.7. RS-232C Communication Command

(Digital Video Recorder to Controller) ................................................ 51

16.2. About the Ethernet Terminal .......................................................................... 53

17. RACK MOUNTING ........................................................................................... 54

WHEN YOU NEED HELP

18. IF YOU THINK THERE IS A FAILURE: (TROUBLESHOOTING) .... 55

19. SPECIFICATIONS ........................................................................................... 56

NTSC version complies with Part 15 of the FCC Rules.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Modifications

Any modifications made to this device that are not approved by TOA Corporation may void the authority

granted to the user by the FCC to operate this equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. SAFETY PRECAUTIONS

• Be sure to read this safety instructions in this section carefully in prior to use.

• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages

regarded as very important precautions are included.

• Keep this instructions handy for future reference.

Safety Symbol and Message Conventions

Safety messages described below are used to prevent bodily injury and property damage that could result

from mishandling. Before operating your product, read this manual first and understand messages so you are

thoroughly aware of the potential safety hazards.

Indicates a potentially hazardous situation which could result in death or

serious personal injury if ignored or mishandled.

WARNING

When installing the Recorder

• This is a class A product. In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures.

• Do not expose the unit to rain or an environment where it may be splashed by water or other liquids, as

doing so may result in fire or electric shock.

• Use the unit only with the voltage specified on the unit. Using a voltage higher than specified one may result

in fire or electric shock.

• Do not damage, modify nor put the power supply cord in close to heaters. Never place heavy objects on the

power supply cord, as doing so may result in fire or electric shock.

• Do not install nor place the unit in unstable locations, such as on a rickety table or a slanted surface. Doing

so may result in the unit falling down or dropping and causing personal injury.

When Using the Recorder

• Should the following irregularity be found during use, immediately switch off the main power, disconnect the

power supply plug from the AC outlet and contact your nearest TOA dealer. Make no further attempt to

operate the unit in this condition as this may cause fire or electric shock.

• If you detect smoke or a strange smell coming form the unit

• If water or any metallic object gets into the unit

• If the unit falls or the unit case breaks

• If the power supply cord is damaged (exposure of the core, disconnection, etc.)

• When the Screen is not Displayed

• Do not open the unit case nor modify the unit. As doing so may result in fire or electric shock as there are

high voltage components inside the unit. Refer any needed servicing to authorized TOA dealers.

• Do not put containers of liquid or metallic objects on top of the unit. If they accidentally spill into the unit, this

may cause a fire or electric shock.

• Do not insert nor drop metallic objects or flammable materials from ventilation slots of the unit, as this may

result in fire or electric shock.

• Do not touch power supply plug during thunder and lightning, as this may result in electric shock.

Indicates a potentially hazardous situation which could result in

moderate or minor personal injury, and/or property damage if ignored

or mishandled.

CAUTION

When installing the Recorder

• Do not plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock.

• When unplugging the power supply cord, be sure to grasp the power supply plug; never pull the cord itself,

as doing so may result in damage the cord, causing fire or electric shock.

• Moving the unit with the power supply cord connected to the wall outlet may cause damage to the power

supply cord, resulting in fire or electric shock.

• Do not block the ventilation slots as this may cause inside of the unit filled with heat, as doing so may result

in fire.

• Do not install the unit in humid or dusty locations, in locations exposed to the direct sunlight, near the

heaters, nor in locations generating soot or steam as doing so may result in fire or electric shock.

Download from Www.Somanuals.com. All Manuals Search And Download.

Indicates a potentially hazardous situation which could result in

moderate or minor personal injury, and/or property damage if ignored

or mishandled.

CAUTION

When Using the Recorder

• Do not place heavy objects on the unit. Such object may fall or the unit may tip over, possibly resulting in

personal injury.

• Clean the unit periodically. Contact your TOA dealer regarding the cleaning. If dust is allowed to accumulate

in the unit over a long period of time, a fire may result.

• Clean the power supply plug and wall AC outlet periodically. If dust accumulates on them, a fire may result.

Insert the power supply plug into the AC outlet securely.

• Switch off the main power and unplug the power supply plug from the AC outlet for the safety purposes

when cleaning or leaving the unit unused for long periods of time. Doing otherwise could cause fire or

electric shock.

2. GENERAL DESCRIPTION

The TOA C-DR0100 (C-DR0101, C-DR0105) is a single-channel Digital Video Recorder with 1 channel of

video input, and permits connected camera images to be recorded onto its large-capacity internal hard disks

using a digital compression system. It can simultaneously play back recorded camera images while continuing

to record images onto the hard disk. The Digital Video Recorder can also be easily connected to an existing

switcher system, replacing previously installed analog time-lapse VCRs. Mounting in EIA-Standard equipment

racks can also be easily performed with the addition of optional rack mounting brackets.

3. FEATURES

High Picture Quality

Digital compression system ensures high-quality picture, audio recording, and playback.

Extended-Time Recording

Built-in 120 GB (C-DR0100), 240 GB (C-DR0101) and 500 GB (C-DR0105) large-capacity hard disks permit

extended-time recording.

Can Be Used In Conjunction With Switchers

Can be connected to TOA’s switcher system and used in place of analog time-lapse VCRs. In systems that

use a Multi-switcher (C-MS91D and C-MS161D), the Series Recording function that permits continuous

recording with the connection of two Digital Video Recorders can be enabled, and the switcher’s motion

detection function can be used as an alarm input to provide efficient surveillance by means of Alarm

Recording.

Simultaneous Recording/Playback

Recorded images can be played back without interrupting recording.

Pre-Alarm Recording

Pre-Alarm function performs retroactive recording to a maximum of 5 minutes before alarm activation.

Search Function

Three search functions Date/Time Search, Block Search, and Time Shift Search permit desired scenes to be

quickly found and viewed.

Mirroring Recording (C-DR0101, C-DR0105)

The C-DR0101 and C-DR0105 has two built-in hard disk drives. Mirroring refers to the simultaneous recording

of data onto the two hard disks. Even if one of the disks fails, recording and playback can still be performed

using the other disk. The possibility of data loss due to hard disk failure is greatly reduced, increasing

reliability.

Networking Function

An RS-232C interface and a 100BASE-TX Ethernet port are standard.

Note: The RS-232C control software is not standard.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. HANDLING PRECAUTIONS

• Use the Digital Video Recorder in locations with ambient temperature of between +5°C and +40°C, and

humidity levels of less than 80% to ensure that no condensation is formed.

• When moving the Recorder, first switch off the main power and then wait at least 30 seconds before moving.

• Avoid moving the Recorder suddenly from a cold location to a warm location, or installing it in close proximity

to an air-conditioner outlet, as internal condensation could result. When condensation occurs, do not switch

on the power until the Recorder has sufficiently dried.

• Avoid installing the Recorder in humid or dusty locations, or in locations exposed to direct sunlight, sooty

smoke or steam. Note that even in locations which are not particularly dusty, dust may accumulate at the

Recorder’s ventilation slots. Because this could cause an extreme rise in temperature inside the Recorder,

be sure to clean the ventilation slots periodically after switching off the main power and disconnecting the

power supply cord from the AC outlet. It is highly recommended that the ventilation slots be cleaned once a

year.

• The socket-outlet shall be installed near the equipment and the plug (disconnecting device) shall be easily

accessible.

• To clean, be sure to first switch off the main power and then wipe with a dry cloth. If the Recorder is

particularly dirty, use a cloth damped in a neutral detergent. Never use benzene, thinner or chemically-

impregnated towels, which may damage the Recorder’s surface.

• Do not block the ventilation slots or cooling fan, which could cause the temperature inside the Recorder to

rise, possibly resulting in unit failure. Install the Recorder at least 100 mm away from the nearest wall

surface.

• Since the Recorder is equipped with a cooling fan, a motor sound is generated.

• Do not install the Recorder in locations influenced by strong electrical or magnetic fields, as monitor screen

pictures may become distorted or the Recorder could fail.

• Avoid jarring or striking the Recorder. The Recorder is a piece of precision equipment and accidentally

dropping it or subjecting it to strong impacts could cause its failure. When transporting the Recorder,

carefully pack it in the supplied carton to protect it from shock.

• Do not use the Recorder in locations exposed to vibration to avoid failure. Avoid installing the Recorder

vertically or tilting it at extreme angles, since it is designed to be used in a horizontal position only.

• About the hard disks

Hard disks other than those specified by TOA cannot be used. Since the hard disks are pieces of precision

equipment, take special care in handling not to accidentally drop, bump or jar them, lest they should fail.

If a hard disk on which condensation is formed is used, it could fail. Therefore, when brought into a warm

room from the cold outdoors, be sure to leave it unused for at least half a day before using it. If the hard disk

fails, recorded data cannot be restored.

• TOA takes no responsibility for any incidental damage, such as loss of sales opportunities, that may result

from the Digital Video Recorder’s failure.

• The standby function is used to enable transportation of the unit from one place to another when

circumstances do not permit its main power supply to be turned off. While in standby mode, power continues

to be supplied to the unit, but its hard disk and fan are stopped. If the unit is left in standby mode for long

periods of time, heat can build-up inside the unit, potentially shortening its operating life. To avoid this, be

sure to turn off the main power supply when the unit is not in use.

Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the security aspects

of this product. UL has only tested for fire, shock or casualties as outlined in UL's Standard(s) for

Safety. UL Certification does not cover the performance or reliability of the security hardware and

security operating software. UL MAKES NO REPRESENTATIONS, WARRANTIES OR

CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY

SECURITY RELATED FUNCTIONS OF THIS PRODUCT.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. NOMENCLATURE AND FUNCTIONS

[Front Panel]

REVERSE

PLAY

STOP

BUZZER

STOP

MENU SEARCH

DISK FULL/

FAILURE

SELECT

TIMER

REC

PLAY

PAUSE

OUTPUT

ALARM

RESET

VIDEO AUDIO

FRAME

BLOCK

DIGITAL VIDEO RECORDER

5 6

2 3 4

10 1112

Playback [ ] Key

Standby Key [

]

Plays back recorded images in the forward

direction, and continuously lights green during

playback. The playback speed cycles through x1,

x2, x4, and x8 with each depression of the

Playback key.

Pressing this switch while the main power is

supplied initiates a system check (the switch

flashes green) and activates the Digital Video

Recorder (the switch lights green). Holding down

this switch for 1 second or more places the

Recorder in standby mode, indicated by the

switch flashing every 5 seconds.

Frame Advance [ ] Key

Pressing this key while the Recorder is in

Playback Pause mode initiates a frame-by-frame

playback of the recorded image. Holding down

this key performs a continuous frame-by-frame

playback in the forward direction.

Note

Some time is required before the Recorder is

placed in standby mode after the main power has

been switched on. Ensure that the Recorder is in

standby mode before operating the standby key.

Playback Stop [ ] Key

Stops playback operation.

Note

Current recording in progress does not stop even

if this key is pressed.

Timer Key

This key lights green when pressed, indicating

that the Recorder is in Internal Timer Recording

standby mode, which permits Internal Timer

Recording to be performed at preset times. To

cancel Internal Timer Recording, hold down the

Timer key for at least 1 second until its light

extinguishes.

[ + ] and [ – ] Set Keys

Used to change setting values on the menu or

search screen.

Recording [

] Key

Block Shift Key

This key lights red when pressed, indicating that

camera recording is in progress. To stop the

recording, hold down the Recording key for at

least 1 second until its light extinguishes.

Pressing the (+) key during playback shifts the

recorded image block to the next block in the

forward direction, while the (–) key shifts to the

preceding block.

Reverse Playback [ ] Key

Up [ ] and Down [ ] Shift Keys

Used to move the cursor on the menu or search

screen.

Plays back recorded images in the reverse

direction. This key continuously lights green

during reverse playback. The playback speed

cycles through x1, x2, x4, and x8 with each

depression of this key.

Select Key

Selects items or choices on the menu or search

screen.

Frame Reverse [ ] Key

Pressing this key while the Recorder is in

Playback Pause mode initiates a frame-by-frame

reverse playback of the recorded image. Holding

down this key performs a continuous frame-by-

frame playback in the reverse direction.

11 Menu Key

Hold down this key for 1 second or more to

display the main menu screen on the monitor.

Pressing this key during playback stops playback

operation to display the main menu screen. The

main menu screen can also be displayed even

while recording is in progress, however some

items cannot be set during recording. If this key is

pressed during item selection, the displayed

setting contents are set and confirmed, returning

the display to the previous screen.

Pause [ ] Key

Temporary stops playback. This key continuously

lights green while in Playback Pause mode. If

pressed again, images are played back in the

same direction as before. (Playback speed

reverts to normal x1 speed.) When the Pause key

flashes green, this indicates that the Recorder is

in Time Shift Search mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Search Key

Video Output Terminal

Displays the search screen on the monitor.

Pressing this key during playback stops playback

operation to display the search screen. If pressed

while in Playback Pause mode, the Time Shift

Search screen is displayed. To exit the search

screen, press this key again.

Used for dubbing recorded video images. This

terminal is the same as the Video Output

Terminal located on the rear panel.

Audio Output Terminal

Used for dubbing recorded audio signals. This

terminal is the same as the Audio Output

Terminal located on the rear panel.

13 Buzzer Stop Key

This key flashes red when an alarm is activated,

and the Recorder’s built-in buzzer is sounded to

provide both visual and audio alarm warnings.

After Alarm Recording completion, the key

changes to steady ON (red). Press this key to

stop the buzzer. The buzzer can be disabled by

selecting "OFF" for Buzzer in the Alarm

Recording Settings. (Refer to p. 19.)

Alarm Reset Key

Hold down this key for 1 second or more to reset

alarm operation and stop Alarm Recoding.

Disk Full/Failure Indicator

Disk Full Indicator

When the Recording mode is set to "STOP" or

"SERIES" in the Disk Setting, the indicator

flashes whenever less than 1 hour of available

hard disk time remains, and changes to steady

ON if no available time remains.

Failure Indicator

This indicator lights red when the Recorder fails,

and extinguishes when the cause of the failure is

removed. This failure indication takes precedence

over the Disk Full indication, should both be

enabled at the same time. Possible Failure

Causes: Hard disk failure, fan failure, and video

loss.

Note

If the Recorder should indicate a failure, first

check for the cause by switching the power OFF,

then contact your TOA dealer if unable to solve

the problem.

Download from Www.Somanuals.com. All Manuals Search And Download.

[Rear Panel]

ALARM RESET OUT

ALARM IN

SW CTRL OUT

TIME SYNC OUT

ALARM OUT

FAILURE OUT

TIME SYNC IN

REC STOP IN

REC START IN

VIDEO

SW VIDEO

ALARM RESET IN

DISK FULL OUT

OUT

OFF

AUDIO

OUT

GND

100BASE–TX

RS–232C

MAIN POWER

AC MAINS

19 20

AC Inlet

Connect the supplied power cord to this socket.

100BASE-TX Terminal

RJ-45 terminal for Ethernet.

Main Power Switch

Power switch for the Digital Video Recorder.

Control Input/Output Terminal

Alarm Reset Input Terminal

Used to permit external equipment to reset the

Recorder’s alarm operation. This terminal

provides the same operation as the front panel-

mounted Alarm Reset key.

Video Input Terminal

Receives video signals. Connect the Multi-

switcher’s VCR output to this terminal when

connecting the Multi-switcher.

Recording Start Input Terminal

Video Output Terminal

Used to permit external equipment to initiate

recording. When the Disk Setting’s Disk Mode is

set to "SERIES," even if the Recorder’s disk is

full, the Disk Full status is reset and recording is

started.

Sends out video signals. Connect this terminal to

the Multi-switcher’s VCR input when connecting

the Multi-switcher. If the Multi-switcher is not

used, connect this terminal to the monitor to

transmit video signals to the monitor.

Recording Stop Input Terminal

Switcher Video Input Terminal

Used to stop recording at external equipment.

This terminal provides the same operation as the

front panel-mounted Recording key.

Connect the Multi-Switcher’s monitor output to

this terminal. This terminal is not used if the Multi-

switcher is not connected.

Time Sync Input/Output Terminals

Switcher Video Output Terminal

Synchronize multiple Digital Video Recorders with

that of a specified recorder (master unit) when

two or more recorders are used. Connect the

master unit’s output to the slave unit’s input.

In the system in which the Multi-switcher is

connected, connect this terminal to the monitor to

transmit video signals to the monitor. Do not use

this terminal if the Multi-switcher is not connected.

Alarm Output Terminal

Shorts to the ground terminal when an alarm is

activated.

Audio Input Terminal

Receives audio signals from the drive unit, etc.

Audio Output Terminal

Sends out audio signals to the monitor, etc.

System Failure Output Terminal

Shorts to the ground terminal when the hard disk

or fan failure or Video Loss occurs.

Control Input/Output Terminal

Alarm Reset Output Terminal

Shorts to the ground terminal when the

Recorder’s alarm is reset.

Disk Full Output Terminal

Shorts to the ground terminal when no available

hard disk time remains.

Alarm Input Terminal

RS-232C Terminal

Activates an alarm by way of external sensors.

Alarm Input mode can be changed by the

Recording Setting’s Alarm Recording Setting.

Connect this terminal to a computer’s RS-232C

terminal when controlling the Recorder at the

computer. Connect this terminal to the Multi-

switcher’s RS-232C terminal to synchronize the

Recorder with the Multi-switcher. (This terminal

can be connected to any of the C-MS91D, C-

MS161D Multi-switchers.)

Ground Terminal

Switcher Control Output Terminal

Connect this terminal to the Multi-switcher’s

switcher control input terminal.

*Ratings and serial numbers are indicated on the

bottom surface.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. SETTING ITEM CHART AND SETTING PROCEDURES

6.1. Basic Setting Procedures

• The shaded

item in the figure refers to the cursor position.

1. Enter the main menu screen.

Camera Display Screen

Main Menu Screen

THU JAN/01/04

00:00:00

MAIN MENU

PLAY SETTING

•

CLOCK SETTING

DISK SETTING

key

REC SETTING

ON–SCREEN DISP SETTING

KEY LOCK

Press key for 1

second or more

COMMUNICATION SETTING

LOG DISPLAY

SYSTEM MAINTENANCE

2. Enter the setting screen.

Setting screen

MAIN MENU

REC SETTING

PLAY SETTING

CLOCK SETTING

DISK SETTING

GENERAL REC SETTING

TIMER REC SETTING

•

SELECT

key

TIMER REC SETTING

ALARM REC SETTING

key

ALARM REC SETTING

•

REC SETTING

•

ON–SCREEN DISP SETTING

KEY LOCK

key

COMMUNICATION SETTING

LOG DISPLAY

SYSTEM MAINTENANCE

3. Select the setting value.

ALARM REC SETTING

ALARM SETTING

[

VALID]

EDGE]

ALARM SETTING

ALARM IN MODE

PRE–ALARM

ALARM PERIOD

POST–ALARM

PICTURE

[

VALID]

EDGE]

ALARM SETTING

ALARM IN MODE

PRE–ALARM

ALARM PERIOD

POST–ALARM

PICTURE

[

VALID]

EDGE]

SELECT

ALARM IN MODE

[

key

PRE–ALARM

[20SEC]

[10SEC]

[20SEC]

[10SEC]

[20SEC]

[10SEC]

key

ALARM PERIOD

POST–ALARM

PICTURE

[LEVEL3]

ON]

[1/30SEC]

ON]

[DURING REC]

[LEVEL3]

ON]

[1/30SEC]

ON]

[DURING REC]

[LEVEL1]

ON]

[1/30SEC]

ON]

[DURING REC]

AUDIO

[

AUDIO

[

AUDIO

[

REC INTERVAL

BUZZER

REC INTERVAL

BUZZER

REC INTERVAL

BUZZER

key

[

ALARM OUT

4. Confirm the selected setting value and return to the camera display screen.

Camera Display Screen

REC SETTING

MAIN MENU

THU JAN/ 01/ 04

00:00:00

key

GENERAL REC SETTING

PLAY SETTING

•

TIMER REC SETTING

ALARM REC SETTING

CLOCK SETTING

DISK SETTING

REC SETTING

ON–SCREEN DISP SETTING

KEY LOCK

COMMUNICATION SETTING

LOG DISPLAY

SYSTEM MAINTENANCE

Download from Www.Somanuals.com. All Manuals Search And Download.

6.2. Setting Item Chart

Main Menu Item

Menu Item

Setting Item

Playback Mode

Main Menu

Playback Settings (p. 13)

Simultaneous Recording/Playback

Year/Month/Day

Clock Settings (p. 14)

Time Synchronization

Synchronization Time

Summer Time

Disk Settings (p. 15)

Disk Mode

Recording Mode

Picture Quality

Audio

General Recording

Settings (p. 17)

Recording Settings (p. 16)

Recording Intervals

Switcher Control Period

Internal Timer Recording

Settings (p. 17)

Timer Setting List

Timer Setting 01–10

Recoding Start Date

Preset Time

Picture Quality

Audio

Recording Intervals

Recording Pattern

Motion Detection Pattern

Alarm Settings

Alarm Input Mode

Pre-Alarm Recording Periods

Alarm Recording Periods

Post-Alarm Recording Periods

Picture Quality

Alarm Recording Settings

(p. 19)

Audio

Recording Intervals

Buzzer Sound

Alarm Output Time

Picture Quality Indication

Audio ON/OFF Indication

Recording Mode Indication

Recording Indication

Playback Indication

Remaining Time Indication

Date Indication

Screen Display Settings (p. 21)

Time Indication

Date/Time Display Position

Disk Mode Indication

Key Lock (p. 22)

Communication Settings (p. 23)

RS232C Baud Rate

RS232C Flow Control

Network Settings

IP Address

Subnet Mask

Default Gateway

Switcher Synchronization

Log Display (p. 24)

General/Timer Recording Log

Alarm Recording Log

Failure Log

System Maintenance (p. 25)

Menu Default Settings

Disk Formatting

Disk Selection

* This setting item is applicable to the C-DR0101 and C-DR0105 Recorder, and not displayed on the screen

when the C-DR0100 Recorder is used.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. INDIVIDUAL ITEM SETTINGS

7.1. Main Menu Screen

Hold down the Menu key for 1 second or more on the screen displaying the camera to display the Main

Menu screen.

• Select the desired item from 9 main menu items on the

main menu screen.

MAIN MENU

PLAY SETTING

Refer to P.13

• Move the cursor with the ( ) or ( ) key, and display each

setting screen with the Select key.

•

CLOCK SETTING

DISK SETTING

REC SETTING

ON–SCREEN DISP SETTING

KEY LOCK

COMMUNICATION SETTING

LOG DISPLAY

SYSTEM MAINTENANCE

Refer to P.14

Refer to P.15

Refer to P.16

Refer to P.21

Refer to P.22

Refer to P.23

Refer to P.24

Refer to P.25

Note

Be sure to first perform Clock Settings (Refer to p. 14) before performing each setting.

7.2. Playback Settings

Playback mode settings are only available to the C-DR0101 and C-DR0105, and not displayed when the C-

DR0100 is used.

PLAY MODE : Sets the hard disk to be used for playback and search functions.

SIMUL REC/PLAY : Selects "ALLOW" or "DISALLOW" for simultaneous recording and playback operations.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

PLAY SETTING

PLAY MODE

SIMUL REC/ PLAY

[

ALL]

[

ALLOW]

screen.

• Each setting item and its setting value and contents are as shown in

the table below.

Setting Item

PLAY MODE

Setting Value

Contents

ALL / HDD-A / HDD-B

ALL

: All set hard disks are used for playback.

(Playback Mode)

(C-DR0101, DR0105)

SIMUL REC/PLAY

(Playback during

Recording)

HDD-A : Hard disk drive A is used for playback.

HDD-B : Hard disk drive B is used for playback.

ALLOW / DISALLOW

ALLOW

: Allows playback while recording.

DISALLOW : Disallows playback while recording.

* The underlined contents are factory-preset values.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.3. Clock Settings

Set the date and time. Perform this setting when the Recorder is used for the first time or when the date and

time indication has been deleted because the power was switched off for a long period of time.

Note

• Previously logged data times are not updated even if the Clock Settings are changed during use.

• The data times will be lost if the power was switched off for 30 days or more. Set the date and time again.

Memory backup: 720 hours (fully charged)

TIME SYNC : Synchronizes the times of other Recorders (slave units) with that of a specified Recorder

(master unit) when multiple Recorders are used.

SYNC TIME : Sets the synchronization time.

Note

The Time Sync function cannot be operated during recording.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• After completing the settings of time (hour, minute, second), confirm

CLOCK SETTING

THU JAN / 01 / 04

TIME SETTING : SELECT KEY

00:00:00

the time with the Select key.

• The indication "Clock Setting Completed" is displayed on the screen

after setting completion.

TIME SYNC

SYNC TIME

SUMMER TIME SETTING

[

SLAVE]

[00H]

• Current time is displayed in the lowest part of the screen.

• Confirm the setting with the Menu key, and return to the previous

screen.

THU JAN / 01 / 04

00:00:00

• Each setting item and its setting value and contents are as shown in

the table below.

Setting Item

Setting Value

MASTER / SLAVE

Contents

TIME SYNC

MASTER: Designates the master unit.

(Time

SLAVE: Designates the slave unit.

Synchronization)

...

SYNC TIME (Synch- 00H / 01H / 02H / 03H / 04H /

ronization Time) up to 23H

Select and set the synchronization time.

* The underlined contents are factory-preset values.

Note

Setting the Time Sync settings to "SLAVE," and the Disk Setting’s Disk Mode to "SERIES" places the

Recorder in Disk Full mode, causing the Disk Full indicator to light. Perform this setting when using Series

Recording. Refer to p. 41; Expansion System (Series Recording).

Download from Www.Somanuals.com. All Manuals Search And Download.

7.3.1. Summer Time (Daylight Saving Time) Setting

Summer Time Setting screen is displayed if Summer Time Setting is selected on the Clock Setting screen.

• Move the cursor with the ( ) or ( ) key, and change setting values with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous screen.

• Each setting item and its setting value and contents are as shown in the table below.

Setting Item

Setting Value

Contents

ON : Displays the current date and time by automatically shifting the time

from standard local time to summer time and from summer to

standard time.

SUMMER TIME

SETTING

ON / OFF

OFF : Displays the current date and time having nothing to do with the

summer time.

Sets the time to shift to the summer time.

SUMMER TIME

FIRST DAY

Month :

Select the "Month" and "Which Sunday" and "What time"

JAN / FEB / MAR / APR / MAY /

JUN / JUL / AUG / SEP / OCT /

NOV / DEC

Which Sunday :

FIRST / SECOND / THIRD /

FOURTH / LAST

What time :

...

00H / 01H / 02H / 03H / 04H /

up to 23H

Sets the time to shift back to the standard local time.

Select the "Month" and "Which Sunday" and "What time"

SUMMER TIME

LAST DAY

Month :

JAN / FEB / MAR / APR / MAY /

JUN / JUL / AUG / SEP / OCT /

NOV / DEC

Which Sunday :

FIRST / SECOND / THIRD /

FOURTH / LAST

What time :

...

00H / 01H / 02H / 03H / 04H /

up to 23H

*The underlined contents are factory-preset values.

Example

(1) If the FIRST DAY time is set to "02H", then at 2:00 AM on the first day of summer time the clock will be

advanced one hour to 3:00 AM.

(2) If the LAST DAY time is set to "02H", then at 2:00 AM on the first day of summer time the clock will be

setback one hour to 1:00 AM.

7.4. Disk Settings

Disk Mode Settings are only available to the C-DR0101, and not displayed when the C-DR0100 is used.

DISK MODE : Sets the hard disk recording method.

REC MODE : Selects "RE-REC","STOP," or "SERIES" for hard disks.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

DISK SETTING

DISK MODE

REC MODE

[

NORMAL]

[

STOP]

screen.

• Each setting item and its setting value and contents are as shown in

the table below.

PLAY CHANGED TO

" ALL "

Setting Item

DISK MODE

(C-DR0101, C-DR0105) MIRRORING

Setting Value

Contents

NORMAL /

NORMAL :

Records continuously on each hard disk.

MIRRORING: Recording is performed simultaneously on the 2 hard disks.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Item

Setting Value

Contents

REC MODE

(Recording Mode)

RE-REC / STOP / SERIES

RE-REC:Automatically deletes old recordings in chronological order to

overwrite the hard disk.

STOP: Performs no further recording to save previously recorded data

if no available hard disk time remains.

The Disk Full indicator flashes red whenever less than 1 hour of

available hard disk time remains, and changes to steady ON

(Indecator lights red) if no available time remains.

Selecting "RE-REC" in the menu resets the Disk Full mode and

causes the Disk Full indicator to extinguish.

SERIES: The Recorder stops and sends out a signal from its rear panel-

mounted Disk Full Output terminal if no available hard disk time

remains. If the Recorder receives a signal at its Recording Start

input terminal when it is in Disk Full mode, the Disk Full mode is

reset, causing the Disk Full indicator to extinguish.

* The underlined contents are factory-preset values.

Note

• Avoid mixing both Normal Recordings and Mirroring Recordings on the hard disk. If mixed, block advance

during playback or search operations cannot be correctly performed during playback. Be sure to re-format

the disk when changing the Disk Mode Setting. Note that all recording data are deleted when formatted.

(Refer to p. 26; "Disk Formatting.")

• Setting the Clock Setting’s Time Sync to "SLAVE" and the Recording Mode to "SERIES" places the

Recorder in Disk Full mode and causes the Disk Full indicator to light. Perform this setting when using the

Series Recording function. (Refer to p. 41; "Expansion System (Series Recording).")

• When the Recording mode is set to "SERIES," timer program cannot be perfomed.

• If the Disk Mode is changed, the Playback Mode changes as follows and the screen indicates that the

Playback Mode has changed. (C-DR0101, C-DR0105)

DISK MODE

NORMAL

PLAY MODE

ALL

MIRRORING

HDD-A

The disk to be used is set to HDD-B if "HDD-B" is selected in the Playback Mode settings. To set to the

"HDD-A" disk again, set the Disk mode to "MIRRORING."

• About Mirroring Recording. (C-DR0101, C-DR0105)

Setting the Disk Mode to "MIRRORING" permits the same recording to be performed simultaneously on the

two built-in hard disks. Should one of the two disks fail, the other disk will continue recording or playing back

to ensure automatic backup. Be sure to first format both disks before performing Mirroring Recording to

make their available recording times equal.

When a difference in available recording time between the two disk drives exists, recording can continue if

one of the two disks becomes full, provided recording time remains available on the other disk. However,

this will no longer be Mirroring Recording. The maximum available Mirroring Recording time can be checked

by setting the remaining time display to "MIN."

7.5. Recording Settings

Set individual recording conditions for General Recording, Internal Timer Recording, and Alarm Recording.

• Move the cursor with the ( ) or ( ) key, and display the selected

setting screen with the Select key.

• Confirm the selected setting with the Menu key, and return to the

previous screen.

REC SETTING

GENERAL REC SETTING

TIMER REC SETTING

ALARM REC SETTING

•

Download from Www.Somanuals.com. All Manuals Search And Download.

7.5.1. General Recording Settings

Set the recording conditions for General Recording.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

GENERAL REC SETTING

PICTURE QUALITY

AUDIO

[LEVEL3]

ON]

[

REC INTERVAL

SW CTRL PERIOD

[1/30SEC]

[01]

screen.

• Each setting item and its setting value and contents are as shown in

the table below.

Setting Item

Setting Value

Contents

PICTURE QUALITY

LEVEL1 / LEVEL2 / LEVEL3 /

LEVEL4 / LEVEL5

LEVEL1 : Angle of view 720 x 240 file size : 64KB (High Picture Quality )

LEVEL2 : Angle of view 720 x 240 file size : 40KB

LEVEL3 : Angle of view 720 x 240 file size : 32KB

LEVEL4 : Angle of view 720 x 240 file size : 24KB

LEVEL5 : Angle of view 720 x 240 file size : 16KB

(Standard Picture Quality)

AUDIO

ON / OFF

ON: Records audio sound simultaneously during recording.

OFF: Records no audio sound during recording.

REC INTERVAL

1/60SEC / 1/30SEC / 1/15SEC / Sets recording intervals.

(Recording Intervals) 1/10SEC / 1/5SEC / 1/3SEC / Setting the Disk Setting’s Disk Mode to "MIRRORING" limits the

1/2SEC / 1SEC / 2SEC / 3SEC / maximum recording interval to 1/30 second. Even if set to "1/60 SEC," the

5SEC /10SEC / 20SEC / 30SEC / actual recording interval is 1/30 second, and the "1/30 SEC" indication is

60SEC

displayed on the screen. (C-DR0101, C-DR0105)

SW CTRL PERIOD

01 / 02 / 03 / 04 / 05 / 10 / 15 / 20/ Set the camera switching signal period.

(Used for switching 30 / 60

cameras by means

of the sequential

switcher, etc.)

The camera switching signal is provided from the Switcher Control Output

at time intervals of recording interval x switching period to switch

cameras. This setting is common to all Recording Modes of General

Recording, Internal Timer Recording, and Alarm Recording.

* The underlined contents are factory-preset values.

7.5.2. Internal Timer Recording Settings

If Internal Timer Recording Settings is selected, the Timer Setting List screen is displayed.

Up to 10 timer programs can be set individually.

Move the cursor to the desired program and press the Select key. The Timer Schedule screen is then

displayed.

TIMER SETTING LIST

START – END

JAN / 01 / 04 00 : 00 ~ 10 : 00

SM – W – F – 12 : 34 ~ 23 : 45

––– / –– / –– –– : –– ~ –– : ––

• Move the cursor with the ( ) or ( ) key, and press the Select Key.

The Timer Schedule Screen is displayed.

• Confirm the setting with the Menu key, and return to the previous

screen.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Timer Schedule Screen Settings

Program No

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

screen.

• Each setting item and its setting value and contents are as shown in

the table below.

TIMER SETTING 01

DATE

[DAILY]

TIME

THU JAN / 01 / 04

00 : 00 – 10 : 00

PICTURE QUALITY

AUDIO

REC INTERVAL

REC PATTERN

MOTION DETECT PTN

[LEVEL3]

[ON]

[1/30SEC]

[1]

Setting Item

DATE

Setting Value

Contents

DAILY / WEEKLY / CANCEL

DAILY :

Designates the Internal Timer Recording date. Timer

schedules can be set for any time between the current time to

one year ahead. The day of the week is automatically

displayed. Programs are automatically deleted after their

preset times are reached.

(Recording Start

Date)

WEEKLY: Designates two or more days of the week. If all days from

Sunday to Saturday are designated, recording is performed

every day.

CANCEL : Cancels preprogrammed settings.

TIME

Designates the timer operating period in minutes. If the same timer preset

time is duplicated, the "TIME SETTING ERROR" indication is displayed

on the screen to the right side of the program number, invalidating the

date setting. In such cases, correctly reset the time. Note that the timer

operating period cannot be set unless the complete time (hour and

minute) is entered.

(Preset Times)

PICTURE QUALITY

LEVEL1 / LEVEL2 / LEVEL3 /

LEVEL4 / LEVEL5

LEVEL1 : Angle of view 720 x 240 file size : 64KB (High Picture Quality)

LEVEL2 : Angle of view 720 x 240 file size : 40KB

LEVEL3 : Angle of view 720 x 240 file size : 32KB

LEVEL4 : Angle of view 720 x 240 file size : 24KB

LEVEL5 : Angle of view 720 x 240 file size : 16KB

(Standard Picture Quality)

AUDIO

ON / OFF

ON: Records audio sound simultaneously during recording.

OFF: Records no audio sound during recording.

REC INTERVAL

1/60SEC / 1/30SEC / 1/15SEC / Designates the Recording intervals.

(Recording Intervals) 1/10SEC / 1/5SEC / 1/3SEC / Setting the Disk Setting’s Disk Mode to "MIRRORING" limits the

1/2SEC / 1SEC / 2SEC / 3SEC / maximum recording interval to 1/30 second. Even if set to "1/60 SEC," the

5SEC /10SEC / 20SEC / 30SEC / actual recording interval is 1/30 second, and the "1/30 SEC" indication is

60SEC

1 / 2

displayed on the screen (C-DR0101, C-DR0105)

REC PATTERN

(Recording Pattern)

MOTION DETECT

PTN (Motion

Transmits a Pattern Selection command from the RS-232C connector

when the preset timer operating time is reached.

1 / 2

Transmits a Pattern Selection command from the RS-232C connector

when the preset timer operating time is reached.

Detection Pattern)

* The underlined contents are factory-preset values.

Note

Pattern 1 command of both the Recording Pattern and Motion Detection Pattern is transmitted from the RS-

232C connector at times other than timer set times such as power-on, after Internal Timer Recording

completion, and during General Recording.

Recording Pattern and Motion Detection Pattern are functions available to the Multi-switcher (C-MS91D, C-

MS161D). For more information on these functions, refer to the instruction manual for the Multi-switcher.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.5.3. Alarm Recording Settings

Alarm Recording has two Alarm Input modes "EDGE" and "LEVEL" and valid setting items differ depending on

each mode.

Alarm Mode set to "EDGE" : Alarm recording time settings are valid.

Post-alarm time settings are invalid.

Alarm Mode set to "LEVEL" : Alarm recording time settings are invalid.

Post-alarm time settings are valid.

(For more information, Refer to p. 20; "About the Alarm Input Mode.")

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

screen.

• Each setting item and its setting value and contents are as shown in

the table below.

ALARM REC SETTING

ALARM SETTING

ALARM IN MODE

PRE–ALARM

[

VALID]

[LEVEL]

[00SEC]

[ 1MIN]

[00SEC]

[LEVEL3]

ALARM PERIOD

POST–ALARM

PICTURE QUALITY

AUDIO

REC INTERVAL

BUZZER

ALARM OUT

[

ON]

[1/30SEC]

ON]

[DURING REC]

[

Setting Item

Setting Value

Contents

ALARM SETTING

VALID / VAL REC / INVALID

VALID :

Validates alarm settings. (Alarm standby mode)

VAL REC : Validates alarm settings only during recording.

INVALID : Invalidates alarm settings. (Rejects alarm inputs.)

EDGE : Performs recording during preset Pre-alarm and Alarm

Recording periods

ALARM IN MODE

(Alarm Input Mode)

EDGE / LEVEL

LEVEL : Performs recording during preset Pre-alarm Recording, Alarm

input, and Post-alarm Recording periods.

PRE-ALARM

00SEC/ 10SEC/ 15SEC/ 20SEC / Performs retroactive recording to a preset time period before alarm

30SEC/ 1MIN/ 2MIN/ 5MIN activation.

ALARM PERIOD

10SEC/ 15SEC/ 20SEC/ 30SEC/ Performs recording during a preset alarm input period following alarm

1MIN/ 2MIN/ 3MIN/ 4MIN/ 5MIN/ activation when the Alarm Input Mode is set to EDGE. (Refer to p. 20;

10MIN

"About the Alarm Input Mode")

POST-ALARM

00SEC/ 10SEC/ 15SEC/ 20SEC/

30SEC/ 1MIN/ 2MIN/ 5MIN

Performs recording during a preset Post-alarm recording period following

the end of alarm activation when the alarm input mode is set to "LEVEL."

PICTURE QUALITY

LEVEL1 / LEVEL2 / LEVEL3 / LEVEL1 : Angle of view 720 x 240; file size : 64KB (High Picture Quality)

LEVEL4 / LEVEL5

LEVEL2 : Angle of view 720 x 240; file size : 40KB

LEVEL3 : Angle of view 720 x 240; file size : 32KB

LEVEL4 : Angle of view 720 x 240; file size : 24KB

LEVEL5 : Angle of view 720 x 240; file size : 16KB

(Standard Picture Quality)

AUDIO

ON / OFF

ON: Records audio sound simultaneously during recording.

OFF: Records no audio sound during recording.

REC INTERVAL

1/60SEC / 1/30SEC / 1/15SEC / Sets the Recording intervals.

(Recording Interval)

1/10SEC / 1/5SEC / 1/3SEC / Setting the Disk Mode of Disk Settings to "MIRRORING" limits the

1/2SEC / 1SEC /

maximum recording interval to 1/30 second. Even if set to "1/60 SEC", the

actual recording interval is 1/30 second, and the "1/30 SEC "indication is

displayed on the screen (C-DR0101, C-DR0105)

BUZZER

ON / OFF

ON: Sounds a buzzer when an alarm is activated. Pressing the Buzzer

Reset key stops buzzer operation.

OFF: Sounds no buzzer during alarm activation.

ALARM OUT (Alarm DURING REC / 1SEC

Output Periods )

The Alarm Output terminal shorts to ground during a set period of time

following alarm activation.

* The underlined contents are factory-preset values.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.5.4. About the Alarm Input Mode

The Alarm Input mode for Alarm Recording can be set to "EDGE" or "LEVEL."

Each input mode operates as follows:

[Recording period when input mode is set to "EDGE"]

Performs continuous recording during Pre-alarm Recording and Alarm Recording Periods.

Alarm Input

Recording

Recording Status

Pre-alarm Period

Alarm Recording Period

Alarm Output

1 Sec

When an alarm output duration is set to 1 second:

[Recording period when input mode is set to "LEVEL"]

Provides continuous recording during periods of time of Pre-alarm Recording, alarm activation, and Post-

alarm Recording.

Alarm Input

Recording

Recording Status

Recording Period Post-alarm Period

Pre-alarm Period

Alarm Output

When an alarm output is provided during alarm recording:

Note

Pre-alarm recording is operated by the Alarm Recording Setting. It does not operate even if an alarm is

activated during General Recording or Internal Timer Recording since they are operated by their own settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.6. Screen Display Settings

The Disk Mode Display item is displayed when the C-DR0101 and C-DR0105 is used.

Set whether to display or hide on-screen characters during playback or recording.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

screen.

• Each setting item and its setting value and contents are as shown in

the table below.

ON–SCREEN DISP SETTING

PICTURE QUALITY

AUDIO

REC MODE

RECORDING

PLAYING

REMAINING TIME

DATE

TIME

[DISP]

DISP]

[

[DISP]

TIME DISP POS

DISK MODE

[UPPER L]

[DISP]

Setting Item

Setting Value

DISP / HIDE

Contents

PICTURE QUALITY

Displays or hides the picture quality indicator during recording or

playback.

AUDIO

DISP / HIDE

Displays or hides the audio indicator when Audio is set to ON during

recording.

REC MODE

Displays or hides the overwrite recording setting status indicator during

recording.

(Recording Mode)

RECORDING

Displays or hides the recording mode status indicator during recording.

(Recording Display)

PLAYING (Playing

back Display)

Displays or hides the playback speed, playback direction, and pause

status during playback.

REMAINING TIME

(Remaining Time

Display)

Disk Mode set to "NORMAL":

DISP / HIDE

Displays or hides Digital Video Recorder's remaining time. The remaining

hard disk time is calculated from the currently recorded picture quality and

recording interval when the Disk Settings Recording Mode is set to

"STOP" or "SERIES."

Disk Mode set to "MIRRORING":

MAX / MIN / HDD-A /

HDD-B / HIDE

Displays or hides Digital Video Recorder's remaining time. The remaining

hard disk time designated is calculated from the currently recorded picture

quality and recording interval when the Disk Settings Recording Mode is

set to "STOP" or "SERIES." (C-DR0101, C-DR0105)

DATE

DISP / HIDE

Displays or hides the current date during recording, and the recorded date

during playback.

(Date Display)

TIME

DISP / HIDE

Displays or hides the current time during recording, and the recorded time

during playback.

(Time Display)

TIME DISP POS

(Date/Time Display

Position)

UPPER L/ UPPER C/ UPPER R/

Sets the date/time display position. Other display positions also change

LOWER L/ LOWER C/ LOWER R depending on the date/time display position.

DISK MODE

(Disk Mode Display)

DISP / HIDE

Displays or hides the disk connection status indicator. (C-DR0101, C-

DR0105)

* The underlined contents are factory-preset values.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.7. Key Lock

This function validates key locking.

If validated, any key other than the Menu key is not accepted. Pressing keys other than the Menu key sounds

a warning tone.

• The password input screen is displayed if Key Lock is selected on the

KEY LOCK

main menu screen. Press the (–), (+), ( ), and ( ) keys (in that

order) as a password. The " " indication is displayed on the screen

to confirm each key entry as the keys are pressed.

ENTER

PASSWORD.

[

]

Note

The password and the key entry order cannot be changed.

• Entering the password correctly displays the following screen and

validates key locking.

KEY LOCK

KEY LOCK VALIDATED.

• The following screen is displayed if the wrong password is entered.

KEY LOCK

INVALID PASSWORD

• Pressing the Menu key returns the display to the normal operation screen if the password is entered

correctly. If the wrong password is entered, the display returns to the Main Menu screen. In such cases,

perform the settings again.

7.7.1 Key Lock Release

• Hold down the Menu key for at least 1 second on the normal

operation screen.

• The Key Lock Release screen is displayed.

KEY LOCK RELEASE

ENTER

PASSWORD.

[

]

• Entering the password correctly returns the display to the Main Menu

screen.

• If the wrong password is entered, the "INVALID PASSWORD"

indication is displayed as in the case of the Key Lock setting. Since

the display returns to the normal screen if the Menu key is pressed,

perform release operation.

MAIN MENU

PLAY SETTING

•

CLOCK SETTING

DISK SETTING

REC SETTING

ON–SCREEN DISP SETTING

KEY LOCK

COMMUNICATION SETTING

LOG DISPLAY

SYSTEM MAINTENANCE

Download from Www.Somanuals.com. All Manuals Search And Download.

7.8. Communication Settings

Set the transmission rate and whether or not to use flow control in RS-232C communications. Also set the IP

address, etc. to be used in the Ethernet network.

COMMUNICATION SETTING

• Move the cursor with the ( ) or ( ) key, and change setting values

RS232C BAUD RATE

RS232C FLOW CTRL

NETWORK SETTING

SWITCHER SYNC

[38400]

[OFF]

with the (–) or (+) key.

• Confirm the setting with the Menu key, and return to the previous

screen.

[

OFF]

Setting Item

Setting Value

Contents

RS232C BAUD

RATE

9600 / 19200 / 38400 (bps)

Sets the transmission rate.

RS232C FLOW

CTRL

ON / OFF

Sets Flow Control RTS or CTS

SWITCHER SYNC

(Switcher

ON / OFF / TIME SYNC

ON : Controls the switcher through the RS-232C interface.

OFF : Controls no switcher

Synchronization) *¹

TIME SYNC : Only Time Synchronization can be controlled through the

RS-232C interface.

* The underlined contents are factory-preset values.

Note

*¹Recording Pattern, Motion Detection Pattern, Camera/ VCR mode selection, and Time Synchronization

switcher functions can all be controlled by the Digital Video Recorder. However, when syncronizing the

switcher's clock from the Recorder, set the Recorder's clock Time Synchronization setting to "MASTER."

Time synhronization cannot be performed if set to "SLAVE."

7.8.1. Network Settings

The Network Setting screen is displayed if Network Settings is selected on the communication setting screen.

Perform settings that are appropriate for the network.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

NETWORK SETTING

IP ADDRESS

192. 168. 000. 001

SUBNET MASK

255. 255. 255. 000

DEFAULT GATEWAY

000. 000. 000. 000

• Pressing the Menu key after the setting displays the confirmation

message in the lower part of the screen if the entered IP address is

different from the current IP address.

• Holding down the Select key for at least 1 second on the confirmation

message display screen displays the setting save screen.

• Press the Menu key if performing no setting. The display returns to

the normal communication setting screen.

NETWORK SETTING

IP ADDRESS

192. 168. 000. 001

SUBNET MASK

255. 255. 255. 000

DEFAULT GATEWAY

000. 000. 000. 000

SET THIS SETTING. OK?

YES : SELECT KEY 1SEC

NO : MENU KEY

NETWORK SETTING

SAVING SET DATA NOW.

PLEASE WAIT FOR

WHILE.

Download from Www.Somanuals.com. All Manuals Search And Download.

• The figure at right is displayed after saving completion.

• Pressing the Menu key returns the display to the communication

setting menu screen.

NETWORK SETTING

• Switch the power OFF and back ON again to validate the network

setting. (Turn off and on the rear-panel mounted Main Power switch.)

Note

NETWORK SETTING CHANGED.

TURN POWER OFF AND ON TO

VALIDATE THE SETTING.

PRESS MENU KEY

TO RETURN.

Network camera’s settings are not enabled at the front-mounted

Standby Key operation.

7.9. Log Display

Log indications include General Recording Log, Alarm Recording Log, and Failure Log.

• Move the cursor with the ( ) or ( ) key, and display Log Screen

with the Select key.

• Return to the previous screen with the Menu key.

LOG DISPLAY

GENERAL/ TIMER REC LOG

•

ALARM REC LOG

FAILURE LOG

7.9.1. General/ Timer Recording Logs (General/ Timer Rec Log)

Logs start and end times of both General and Internal Timer Recordings, and displays from the latest log. Up

to 100 logs are saved, and old logs are deleted in chronological order when this limit is exceeded.

• The display scrolls in page units (1 screen units) as the ( ) or (

key is pressed.

• Return to the previous screen with the Menu key.

)

GENERAL/ TIMER REC LOG

JAN/ 02/ 04

07: 00: 00

TIMER REC END

JAN/ 02/ 04

00: 00: 00

TIMER REC START

JAN/ 01/ 04

REC END

18: 00: 00

09: 00: 00

07: 00: 00

JAN/ 01/ 04

REC START

JAN/ 01/ 04

TIMER REC END

7.9.2 Alarm Recording Logs (Alarm Rec Log)

Logs Alarm Recording start and end times, and displays from the latest log. Up to 500 logs are saved and old

logs are deleted in chronological order when this limit is exceeded.

• The display scrolls in page units (1 screen units) as the ( ) or (

key is pressed.

• Return to the previous screen with the Menu key.

)

ALARM REC LOG

JAN/ 02/ 04

END

07: 00: 00

JAN/ 02/ 04

START

00: 00: 00

18: 00: 00

09: 00: 00

07: 00: 00

JAN/ 01/ 04

END

JAN/ 01/ 04

START

JAN/ 01/ 04

END

Download from Www.Somanuals.com. All Manuals Search And Download.

7.9.3. Failure Logs

Logs detection times and contents for the various different failure modes that can occur in the Digital Video

Recorder, and displays from the latest log. Up to 100 logs are saved and old logs are deleted in chronological

order when this limit is exceeded.

• The display scrolls in page units (1 screen units) as the ( ) or (

key is pressed.

• Return to the previous screen with the Menu key.

)

FAILURE LOG

JAN/ 02/ 04

07: 00: 00

VIDEO FAILURE

JAN/ 02/ 04

00: 00: 00

DISK FAILURE

JAN/ 01/ 04

18: 00: 00

VIDEO FAILURE

JAN/ 01/ 04

09: 00: 00

FAN FAILURE

JAN/ 01/ 04

07: 00: 00

DISK FAILURE

Display Item

Contents

VIDEO FAILURE

Displays this indication when a video signal cutoff (Video Loss) is

detected during recording.

DISK FAILURE

FAN FAILURE

Displays this indication when a disk error is detected.

Displays this indication when fan operation stops.

Note

The current log display does not change even if a new log is added during display.

To confirm the added log, change the page or return to the log item selection screen to display the log again.

All logs are deleted if Menu Default Settings of System Maintenance is performed.

7.10. System Maintenance

Performs menu default settings or format the hard disk.

• Move the cursor with the ( ) or ( ) key, and confirm the Item with

the Select key.

• Return to the previous screen with the Menu key.

SYSTEM MAINTENANCE

MENU DEFAULT SETTING

•

DISK FORMATTING

7.10.1. Menu Default Settings

• Holding down the Select key for at least 1 second clears saved menu

MENU DEFAULT SETTING

setting contents and log information, initializing settings to factory-

preset status. However, clock settings and network settings are

retained.

SET TO DEFAULT?

• Return to the previous screen with the Menu key.

YES : SELECT KEY 1SEC

NO : MENU KEY

Download from Www.Somanuals.com. All Manuals Search And Download.

7.10.2. Disk Formatting

This function initializes the hard disk. If initialized, all previously recorded contents are deleted. However,

setting contents and logs are retained. Hard disks to be formatted can be selected when the C-DR0101 and

C-DR0105 is used.

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Hold down the Select key for at least 1 second to start formatting.

DISK FORMATTING

FORMAT DISKS?

[

ALL]

• Return to the previous screen with the Menu key.

YES : SELECT KEY 1SEC

NO : MENU KEY

(C-DR0101, C-DR0105)

Setting Items

Contents

HDD-A

Formats Hard Disk A

Formats Hard Disk B

Formats all set hard disks.

HDD-B

ALL

Formatting is started by holding down the Select key for at least 1

second again after the reconfirmation message is displayed. Pressing

the Menu key returns the display to the system maintenance screen

without formatting.

DISK FORMATTING

ARE YOU SURE?

YES : SELECT KEY 1SEC

NO : MENU KEY

The disk error message is displayed if a disk error occurs during formatting.

Download from Www.Somanuals.com. All Manuals Search And Download.

8. DIGITAL VIDEO RECORDER ACTIVATION AND TERMINATION

8.1. Recorder's Activation

The switch and key shown in the following figures are used in operation.

Main Power Switch

ALARM RESET OUT

ALARM IN

TIME SYNC OUT

ALARM OUT

TIME SYNC IN

REC STOP IN

VIDEO

SW VIDEO

REC START IN

SW CTRL OUT

FAILURE OUT

ALARM RESET IN

DISK FULL OUT

OUT

OFF

AUDIO

OUT

GND

100BASE–TX

RS–232C

MAIN POWER

AC MAINS

REVERSE

PLAY

STOP

BUZZER

STOP

MENU SEARCH

DISK FULL/

FAILURE

SELECT

TIMER

REC

PLAY

PAUSE

OUTPUT

ALARM

RESET

VIDEO AUDIO

FRAME

BLOCK

DIGITAL VIDEO RECORDER

Standby Key

1. Connect each component correctly. (Refer to p. 40; "Connections.")

2. Set the rear-panel mounted Main Power switch to the ON position.

The Standby key flashes green for 5 seconds while settings are initialized. Thereafter, the Recorder is

placed in standby mode. The Standby key flashes every 5 seconds while in standby mode.

Note

Do not turn off the Main Power switch while the Standby key is flashing. Ensure that the Recorder is in the

standby mode when turning off the Main Power switch.

Logged data could be damaged or lost if the main power is switched off during initialization (while accessing

the hard disk).

3. Press the Standby key while the Recorder is in standby mode.

The screen automatically changes as shown below.

The Standby key flashes green during a system check.

V e r

SYSTEM CHECK IN PROGRESS

PLEASE WAIT

SYSTEM CHECK COMPLETED

After system check completion, the Standby key changes from flashing to steady ON, allowing camera images

to be displayed.

Note

When the Recorder is used for the first time or when the power was switched off for a long period of time, the

date and time could not be correctly displayed. Perform the clock setting before use. (Refer to p. 14; "Clock

Settings.")

Download from Www.Somanuals.com. All Manuals Search And Download.

8.2. When the Failure Screen Is Displayed:

Note

• Avoid operating any key during a system check after the Standby key

has been pressed. The failure indication shown in the figure at right

could be displayed. In such cases, switch the power OFF and back

ON again.

DISKS MAY HAVE FAILED.

• If the failure indication is still displayed even though the power is

reactivated, format the hard disk. (Refer to p. 26; "Disk Formatting.")

• If the failure indication does not disappear even though the disk is

formatted, the disk ‘s failure may be the cause. Please contact your

TOA dealer.

PLEASE TURN POWER SWITCH

OFF AND ON AGAIN.

8.3. Recorder’s Termination

1. Hold down the Standby key for at least 1 second.

All operations stop, placing the Recorder in standby mode.

Note

The Recorder’s operation can be terminated by holding down the Standby key for at least 1 second even

while in General Recording mode. However, when the Recorder is next reactivated, the previous recording is

not retained and the Recorder is put into Pause mode. Preprogrammed timer times are set revised even if the

Recorder is terminated during the timer setting and activated again.

2. Set the Main Power switch to the OFF position.

The Recorder’s power is switched off.

9. OPERATION AFTER POWER FAILURE RESTORATION

The Recorder’s set contents are never reset by power failures.

However, since the date and time are backed up by the built-in battery, if no power is supplied for a long

period of time (1 month), they are reset. In such cases, perform the clock setting again.

9.1. When the Power Fails during Recording;

• During General Recording

Recording is restarted when the power is restored.

• During Alarm Recording

If an alarm input still continues when the power is restored, it is recognized as a new alarm input and

recording is restarted. However, if no alarm exists, recording is not performed. Also, even if the power is

restored within the set Alarm Recording time period or Post-alarm time period, recording is not restarted

because there is no alarm signal.

• During Internal Timer Recording

Timer operation is restarted if the power is restored within the set time period. If restored during Internal

Timer Recording, the recording is restarted.

Download from Www.Somanuals.com. All Manuals Search And Download.

10. RECORDING

10.1. Type of Recording

Recording modes include General Recording, Internal Timer Recording, and Alarm Recording. Each recording

mode permits the picture quality and recording interval to be set individually. (Refer to p. 17; "General

Recording Settings.") In the Digital Video Recorder, recorded data from the start to the end of each recording

is handled as a single recorded block.

10.1.1. Recording Priorities

The order of Recording Priority is as shown below.

Order of Priority

High

Low

General Recoding

Alarm Recoding

Internal Timer Recording

Type of Recording

Lower-priority recording stops whenever higher-priority recording is commenced. The following figure shows

an example of recording operation that varies whenever recording of different priority levels is commenced.

General Recording

Alarm Recording

Internal Timer Recording

Alarm Input

Rec. key pressed

Recording End

Alarm Input

Alarm End

Timer Key pressed

Note

Internal Timer Recording does not operate even if the Timer key is pressed during General or Alarm

recording. Pressing the Recording ( ) key during a timer setting cancels the timer setting. To resume the

timer setting, first stop recording and press the Timer key.

10.2. Screen Display during Recording

The screen display setting is factory-preset to "DISP." (Refer to p. 21; "Screen Display Settings".)

THU JAN / 01 / 04

00 : 00 : 00

REC

00 : 00 : 00

•

LEVEL3

1 / 60

* C-DR0101, C-DR0105

Indicates the recording status. (Refer to p. 17; "General Recording Settings".)

REC:

Represents General Recording is in progress.

•

TIMER: Represents Internal Timer Recording is in progress.

ALARM: Represents Alarm Recording is in progress.

Indicates the recording picture quality.

Can be set to Levels 1 – 5.

LEVEL 1 provides the highest resolution display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Indicates the recording interval.

General Recording and Internal Timer Recording : 1/60 – 60 seconds

Alarm Recording : 1/60 – 1 seconds

Note

• Even if the Recording Setting’s Recording Interval is set to "1/60 SEC," Mirroring Recording is performed at

the recording interval of 1/30 second. (The on-screen interval indication is also "1/30 SEC" in Mirroring

Recording.) (Refer to p. 17; "General Recording Settings.")

• The higher the picture quality (resolution) and the shorter the recording interval, the shorter the possible

recording time. Conversely, the lower the picture quality and the longer the recording interval, the longer the

possible recording time. (Refer to p. 45; "Recording Time Table.")

Indicates whether or not to use the Audio recording function.

: Audio recording ON (enabled)

No indication : Audio recording OFF (disabled)

Indicates the hard disk Recording Mode. (Refer to p. 15; "Disk Settings.")

Re-Rec Mode

Stop Mode

Series Mode

• Re-Rec Mode : Overwrites old hard disk recordings in chronological order even when no available hard disk

time remains.

• Stop Mode :

Stops video recording when no available hard disk time remains.

• Series Mode : Stops video recording when no available hard disk time remains, and sends out a signal

from the Control Terminal’s Disk Full output, allowing other series-connected Digital Video

Recorder to start recording. The slave Digital Video Recorder starts recording when it

receives a signal at its Recording Start input terminal even if its hard disk becomes full.

(Refer to p. 41; "Expansion System (Series Recording).")

Indicates the Disk Mode. (C-DR0101, C-DR0105) (Refer to p. 15, "Disk Settings".)

No indication : Normal Recording

: Mirroring Recording

• About Normal and Mirroring recordings

The C-DR0101 and C-DR0105 has two built-in hard disks.

Setting the Disk Mode to "NORMAL" permits camera images to be recorded on the second hard disk when

the first hard disk becomes full.

Setting the Disk Mode to "MIRRORING" permits the same recording to be simultaneously performed on the

two hard disks. Even if one of the two disks fails, recording and playback can still be performed using the

other disk.

Indicates the hard disk recognition status. (C-DR0101, C-DR0105)

Characters are reversed for the hard disk in recording mode.

The "X" indication is displayed when the hard disk fails.

Note

Even if the Screen Display Setting’s Disk Mode Indication is set to "HIDE," the "X" indication is

displayed when the hard disk fails.

Indicates the remaining hard disk recording time calculated from the picture quality and recording interval

of current recording.

If the Disk Setting’s Recording Mode is set to "RE-REC", the remaining hard disk recording time is not

displayed.(Refer to p. 15; "Disk Settings".)

Indicates the current date and time.

The "F" indication flashes when the fan fails.

Cannot be set to "HIDE" in Screen Display Settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

10.3. The Keys to Be Used in Recording

The following keys are used in recording:

REVERSE

PLAY

STOP

BUZZER

STOP

MENU SEARCH

DISK FULL/

FAILURE

SELECT

TIMER

REC

PLAY

PAUSE

OUTPUT

PLAY

ALARM

RESET

VIDEO AUDIO

FRAME

BLOCK

DIGITAL VIDEO RECORDER

Buzzer Stop Key

Timer Key

Recording Key

10.4. Performing General Recording (Refer to p. 17; "General Recording Settings)

Note

Be sure to perform time and date settings before recording. (Refer to p. 14; "Clock Settings")

1. Press the Recording key (

) to start General Recording.

THU JAN/ 01/ 04

00 : 00 : 00

When recording is started, the Recording key lights red.

If "DISP" has been selected in Screen Display Settings, setting data

is displayed on the monitor and the Recording indication is displayed

for recording status.

Note

When the Disk Setting Recording Mode has been set to "STOP" or

"SERIES," the Disk Full indicator flashes if less than 1 hour of available

hard disk time remains. If no available hard disk time remains, the Disk

Full indicator changes to steady ON and recording stops.

REC

•

LEVEL3 1/60

: AB

2. Hold down the Recording key (

The illuminated Recording key extinguishes.

) for at least 1 second to stop recording.

Note

If an alarm is activated during General Recording performance while in alarm standby mode, the General

Recording is interrupted and switched over to Alarm Recording. The General Recording is automatically

restored after Alarm Recording completion.

10.5. Performing Internal Timer Recording (Refer to p. 17; "Internal Timer Recording Settings)

Note

Be sure to perform date and time settings before recording. (Refer to p. 14; "Clock Settings".)

1. Press the Timer key.

The Digital Video Recorder is placed in Internal Timer Recording

standby mode, and the Timer key lights green.

THU JAN/ 01/ 04

00 : 00 : 00

2. When the preset time is reached or if the key is pressed within the

preset period, the Recording key lights red and recording is started.

If "DISP" has been selected in Screen Display Settings, setting data

is displayed on the monitor, and the "TIMER" indication is displayed

for recording status.

TIMER

•

LEVEL3 1/60

M : AB

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Recording stops when the end of the preset recording period is reached.

The illuminated Recording key extinguishes.

Note

• When the Disk Setting Recording Mode is set to "STOP," recording stops if no available hard disk time

remains.

• When the Recording mode is set to "SERIES," timer program cannot be perfomed.

• When an alarm is activated during Internal Timer Recording, the Internal Timer Recording is interrupted, and

automatically restored after Alarm Recording completion.

• Pressing the Recording key (

switches it over to General Recording.

) during Internal Timer Recording resets Internal Timer Recording, and

4. To cancel Internal Timer Recording, hold down the Timer key for at least 1 second. The illuminated Timer

key extinguishes.

10.6. Performing Alarm Recording (Refer to p. 19; "Alarm Recording Settings)

Note

• Be sure to perform date and time settings before recording. (Refer to p. 14; "Clock Settings".)

• Be sure to set the Alarm Recording Setting’s Alarm Setting to "VALID" when performing Alarm Recording.

This places the Digital Video Recorder in alarm standby mode.

• The setting is factory-preset to "VALID."

1. A buzzer is sounded and the Buzzer stop key flashes red when an alarm signal is received. At the same

time, the Recording key lights red and recording is started. The

Buzzer stop key continues flashing red during Alarm Recording.

THU JAN/ 01/ 04

00 : 00 : 00

• If "DISP" has been selected in Screen Display Settings, setting data is

displayed on the monitor, and the "ALARM" indication is displayed for

recording status.

• Pressing the Buzzer stop key during buzzer output stops the buzzer.

Whether or not to sound a buzzer can be set by selecting ON or OFF

in Alarm Recording Settings.

• Alarm Recording provides an open collector signal from the Alarm

Output Terminal. An alarm output duration can be set to "1 SEC" or

"DURING REC" in Alarm Recording Settings.

ALARM

•

LEVEL3 1/60

M : AB

2. Recording stops when the end of the Preset Alarm Recording Period is reached. The illuminated Recording

key extinguishes, however the Alarm Reset key remains lit. To reset Alarm Recording before the Preset

Alarm Dcording Period is started, hold down the Alarm Reset key for at least 1 second.

Note

• Pressing the Recording key (

) during Alarm Recording resets Alarm Recording, and switches it over to

General Recording. However, the Alarm Reset key continuously lights red to indicate that an alarm has been

activated.

• To extinguish the illuminated Alarm Reset key, hold down the Alarm Reset key for at least 1 second.

• If the Alarm Recording’s Alarm Settings is set to "VAL REC," alarm signals are only accepted while

recording is in progress. Alarm inputs can be only accepted during the necessary surveillance period by

combining both Alarm and Internal Timer recordings.

• If the Alarm Recording’s Alarm Settings is set to "INVALID," any alarm input is not accepted.

• If other alarms are activated during Alarm Recording, the preset alarm time is initialized to make the

recording period longer. In this case, the number of recorded blocks is one.

Download from Www.Somanuals.com. All Manuals Search And Download.

11. PLAYBACK

11.1. Type of Playback

The Digital Video Recorder features the simultaneous recording/playback function that permits recorded

images to be played back without stopping recording. The types of playback include Playback, Reverse

Playback, Fast Forward Playback, Fast Reverse Playback, Forward Frame Playback, and Reverse Frame

Playback.

Note

• When the Playback Setting’s Simultaneous Recording/Playback is set to "DISALLOW," playback cannot be

performed during recording. Only recording or playback can be performed.

• Playback performance could be degraded during simultaneous recording/playback operation.

11.2. Screen Display during Playback

Screen Display Settings is factory-preset to "DISP." (Refer to p. 21; "Screen Display Settings.")

THU JAN / 01 / 04

00 : 00 : 00

x 2

LEVEL3

•

1 / 60

* C-DR0101, C-DR0105

Indicates playback mode.

: Fast Reverse Playback

: Fast Forward Playback

: Reverse Playback

: Playback

: Pause

• Pressing the Playback key ( ) during playback (or the Reverse Playback key ( ) during Reverse

playback) changes the mode to Fast Forward playback (Fast Reverse playback during Reverse playback).

The "x2", "x4" or "x8" indication is displayed on the screen to indicate the playback speed.

• Pressing the Playback key ( ) or the Reverse Playback key ( ) during still picture playback (while in

pause mode) changes the mode to Forward or Reverse Frame playback. Holding down the key performs a

continuous frame-by-frame playback of the recorded image.

Indicates the recording picture quality.

Can be set to Levels 1 – 5. Quality increases as the number decreases.

Indicates the recording interval.

General Recording, Internal Timer Recording : 1/60 – 60 seconds

Alarm Recording : 1/60 – 1 seconds

Indicates an attribute of Mirroring Recording. (C-DR0101, C-DR0105)

No indication : Data other than Mirroring Recording data

M :

Mirroring Recording data

Indicates the currently-used hard disk. (C-DR0101, C-DR0105)

A : Playback of Hard disk A

B : Playback of Hard disk B

Indicates recording dates and times.

The ( ) indication is displayed when recording is also performed simultaneously with playback.

The "F" indication flashes when the fan fails.

This indication cannot be set to "HIDE" in Screen Display Settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

11.3. The Keys to Be Used in Playback

The following keys are used in playback.

Reverse Playback key, Pause key, Playback key, Playback Stop key, Block Shift key

REVERSE

PLAY

STOP

BUZZER

STOP

MENU SEARCH

DISK FULL/

FAILURE

SELECT

TIMER

REC

PLAY

PAUSE

OUTPUT

ALARM

RESET

VIDEO AUDIO

FRAME

BLOCK

DIGITAL VIDEO RECORDER

Block Shift key

Playback Stop key

Playback key

Reverse Playback key

Pause key

11.4. Performing Playback

1. Press the Playback key ( ) to start playback.

The Playback key lights green when playback is started.

If Screen Display Settings has been set to "DISP," setting data is displayed on the monitor, and the

"Playback" indication is displayed for playback status.

2. Press the Playback Stop key (

to stop playback. The illuminated Playback key extinguishes.

)

11.5. Performing Various Playback Fanctions

11.5.1. Reverse Playback

Press the Reverse Playback key ( ) to perform playback in the reverse direction.

The Reverse Playback key lights green when Reverse playback is started.

If Screen Display Settings has been set to "DISP," setting data is displayed on the monitor, and the "Reverse

Playback" indication is displayed for playback status.

11.5.2. Fast Forward Playback and Fast Reverse Playback

Pressing the Playback key ( ) during playback (or the Reverse Playback key ( ) during Reverse playback)

changes the playback mode to Fast Forward (or to Fast Reverse playback if pressed during Reverse

playback). The playback speed changes as the key is pressed.

Playback speed: Original speed

Twofold speed (x2)

Fourfold speed (x4)

Eightfold speed (x8)

Note

Playback may not be performed at the indicated speed depending on the hard disk performance, such as

access times.

11.5.3. Playback Pause (Still Picture)

1. Pressing the Pause key ( ) during playback or Reverse playback suspends playback operation, causing

the Pause key to light green.

If Screen Display Settings has been set to "DISP," setting data is displayed on the monitor, and the "Pause"

indication is displayed while in pause mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Pressing the Pause key ( ) again returns the Digital Video Recorder to the playback mode it was last in

before playback was suspended.

The illuminated Pause key extinguishes and the Playback key lights.

11.5.4. Forward Frame Playback and Reverse Frame Playback

If the Playback key ( ) or Reverse Playback key ( ) is pressed while in Playback Pause mode, Forward or

Reverse Frame playback can be performed.

Pressing the key once performs a single-frame playback per screen, while holding down the key provides a

continuous frame-by-frame playback.

11.5.5. Forward Block Playback and Reverse Block Playback

In the Digital Video Recorder, recorded data from the start to the end of each recording is handled as a single

recorded block. Since both the Forward Block Playback and Reverse Block Playback functions shift playback

images on a block basis, desired scenes can be searched while viewing playback images.

Pressing the (+) Block Shift key during playback shifts the recorded image to the head of the next block,

temporarily stopping playback for 1 second before it is restarted. If the (+) Block Shift key is pressed again

while in Playback Pause mode, the recorded image is shifted to the next block, providing the same operation.

Press + Press +

Press +

Block

Playback

Pressing the (–) Block Shift key during playback shifts the recorded image to the head of the block currently

played back, temporarily stopping playback for 1 second before it is restarted. If the (–) Block Shift key is

pressed again while in Playback Pause mode, the recorded image is shifted to the head of the preceding

block and then it is played back.

Press

while in Playback Pause mode.

Press

Block

Playback direction

Block shift is also possible during Reverse Playback operation, however playback resumes in the forward

direction after the recorded image has been shifted to the head of the desired block.

Download from Www.Somanuals.com. All Manuals Search And Download.

11.6. About the Playback Start Position

• If playback is initiated from the camera display screen, the playback begins from the position at which it was

last stopped. When the power is switched on or when the position previously played back has been

overwritten, playback is started from the oldest recorded image. During recording, playback is started from

the most recent data in the currently recorded block.

• Pressing the Playback key ( ) (or the Reverse Playback key ( )) while holding down the Playback Stop

key (

while in Stop or Playback mode shifts the recorded image to the following position for playback.

)

Current position

Press

Most recent block

Oldest block

Playback direction

• Pressing the Playback key ( ) (or the Reverse Playback key ( )) while holding down the Playback Stop

key (

during recording causes playback to be started from the following position.

)

Current position

(recording is in progress)

Block

Playback direction

Press

(playback from the

most recent data)

Note

When playing back in the forward direction, if the Pre-alarm time has been set to 10 second or more and the

Digital Video Recorder is in alarm standby mode, playback is started from 10 minutes before the most recent

block is played back.

Download from Www.Somanuals.com. All Manuals Search And Download.

12. SEARCH FUNCTIONS

The following three methods are available to search recorded data (images):

1. Date/Time Search : Playback can be initiated by designating the date and time.

2. Block Search :

Playback can be initiated by selecting the recorded block.

3. Time Shift Search : Playback can be initiated by increasing or decreasing times from the designated time.

The Digital Video Recorder handles recorded data from the start to the end of each recording as a single

recorded block.

The above three search methods differ in operation.

12.1. The Keys to Be Used in Searching

The following keys are used in search operation:

Select key

Search key

REVERSE

PLAY

BUZZER

STOP

MENU SEARCH

DISK FULL/

FAILURE

SELECT

TIMER

REC

PLAY

PAUSE

OUTPUT

STOP

ALARM

RESET

VIDEO AUDIO

FRAME

BLOCK

DIGITAL VIDEO RECORDER

Pause key

Playback key

Down Shift key

Up Shift key

Playback Stop key

Block Shift key

12.2. Date/Time and Block Searches

12.2.1. Basic Date/Time Search and Block Search Operations

1. Press the Search key.

The Search menu screen is displayed.

Playback stops if the key is pressed during playback.

Pressing the Search key again returns the display to the camera

image screen.

DATE / TIME SEARCH

BLOCK SEARCH

•

2. Move the cursor to select the desired search function with the ( ) or

) key, then confirm the selection with the Select key.

(

Setting Items

DATE/ TIME SEARCH Date/ time data entry

BLOCK SEARCH

Setting Value

Contents

Recorded images are searched by directly entering the date and time

Recorded images are searched by selecting the recorded block.

–

12.2.2. Date/Time Search Operation

• Move the cursor with the ( ) or ( ) key, and change setting values

with the (–) or (+) key.

• Executing searches with the Select key displays the image of the

designated time on the still picture mode screen. The Pause key

lights green.

DATE / TIME SEARCH

JAN / 01 / 04 00 : 00

• Playback begins if the Pause key ( ) is pressed.

Note

• When no recording exists at the designated time, the first image of

the recorded block following the designated time is displayed.

• Attempting to perform searches beyond the current time results in a

display of the "INVALID SEARCH" indication on the Date/Time

Search screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

12.2.3. Block Search Operation

BLOCK SEARCH

JAN / 01 / 04

• Using the ( ) or ( ) key, move the cursor to scroll the screen and

select the desired block.

21 : 35 : 27

–– : –– : ––

AMJAN / 01 / 04

––––– / –– / ––

The ( ) indication is displayed when data exists before the currently

displayed search screen, while the ( ) indication is displayed when

data exists after the currently-displayed search screen.

[Recorded block types]

Recorded block types are classified by characters "N," "T," and "A."

Item

Contents

General Recording block

Internal Timer Recording block

Alarm Recording block

Note

The Alarm Recording block time represents the time that an alarm was received. If the Pre-alarm function has

been set, Alarm Recording begins from the image recorded before the indicated alarm time.

[Recorded block attribute]

Character M represents data attribute types.

Item

Contents

No Indication Normal Recordung data

Mirroring Recording data

Note

Avoid mixing both Normal Recordings and Mirroring Recordings on the hard disk. If mixed, block shift or

search operations cannot be correctly performed during playback. (Refer to p. 15; "Disk Settings.")

[Hard disk types]

Characters A and B represent built-in hard disk drives.

Item

Contents

Data contained in Hard Disk A

Data contained in Hard Disk B

• Executing searches with the Select key displays the first image of the block on the still picture screen. The

image is played back if the Pause key is pressed. Pressing the (+) or (–) key while in the Pause mode

displays the first image of the block, performing playback from one block to another. After the block has

switched over to another block, playback can be performed even without pressing the Pause key.

• "Loop" playback is performed for all playback operations after Block Shift search.

Note

• "Loop" playback: Repeats playback of each recorded block.

• Pressing the Playback Stop key ( ) and the Playback key ( ) again during "Loop" playback resets the

"Loop" playback, causing playback to be performed on a time basis.

Head of the selected block

Press

^Press+

Block

“Loop” playback

Download from Www.Somanuals.com. All Manuals Search And Download.

12.3. Time Shift Search

1. Press the Pause key on the playback screen to suspend playback.

2. Press the Search key.

THU JAN / 01 / 04

00 : 00 : 00

The Time Shift Search screen is displayed, and the Pause key

flashes.Pressing the Search key again returns the display to the

playback pause screen.

SHIFT TIME CHANGE :

SHIFTING

CANCEL

: – / +

3. Using the ( ) or ( ) key, change the time period to be shifted.The

shift time period increases as the ( ) key is pressed, and decreases

as the ( ) key is pressed. It can be set to a variable period of 1 – 60

minutes.

: SEARCH

SHIFT: 10MIN

LEVEL3

1/60

4. Press the (+) or (–) key.

The (+) key advances the shift time period by the designated length of time, while the (–) key reverses the

time period by the same designated length of time. If no image exists at the designated time, pressing the

(+) key displays the image following the designated time, while the image preceding the designated time is

displayed if the (–) key is pressed.

5. Press the Search key to reset the Time Shift Search.

The display is temporarily stopped at the searched Time Shift screen.

6. Press the Pause key to begin playback of the searched image.

Note

• Continuous or normal forward/reverse frame playback can also be performed even when the Time Shift

Search screen is displayed (even while the Pause key is flashing).

• If Time Shift Search operation exceeds the range of "Loop" playback during "Loop" playback, the "Loop"

playback is reset, reverting to normal playback.

When the Time Shift Search function is operated within the "Loop" playback range:

Pause

Time Shift

Block

“Loop” playback

When the Time Shift Search function is operated beyond the "Loop" playback range:

Pause

Time Shift

Block

Playback operation on a time basis

Block

Download from Www.Somanuals.com. All Manuals Search And Download.

13. CONNECTIONS

13.1. Preparations for Connections

Switch off the power to the Digital Video Recorder and all connected equipment before performing

connections. The Digital Video Recorder has built-in hard disks. To avoid damage to them, when moving the

Digital Video Recorder, be sure to leave the Recorder’s Main Power switch turned off for at least 30 seconds

before moving.

13.1.1. Control Input/Output Terminal Connections

Applicable cables are as follows:

• Solid cable :

AWG28 (ø 0.32mm) – AWG22(ø 0.65mm)

• Twisted cable: AWG28 (0.08mm²) – AWG22(0.32mm²)

To connect, remove the cable sheath 10 mm from the cable end, and then insert the cable into the terminal

pressing on the tab on the terminal using a screwdriver.

13.2. When Using the 24V AC or 12V DC or AC Mains Camera:

Connect the Digital Video Recorder’s Video Input terminal to the camera’s video output terminal.

13.3. Connections to the Monitor TV

The Digital Video Recorder’s terminals to be connected to the monitor differ depending on the type of

connected equipment.

• When the Digital Video Recorder is not connected to the Multi-switcher:

Connect the Recorder’s Video Output terminal to the monitor’s video input terminal, and the Recorder’s

Audio Output terminal to the monitor’s audio input terminal.

• When the Digital Video Recorder is connected to the Multi-switcher:

Connect the Recorder’s Switcher Video Output terminal to the monitor’s video input terminal, and the

Recorder’s Audio Output terminal to the monitor’s audio input terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

13.4. Combination With The Digital Video Recorder/ Multi-switchers (C-MS91D and C-MS161D)

The Digital Video Recorder has been designed with an emphasis on the synchronization with the TOA Multi-

switchers (C-MS91D, C-MS161D).

By synchronizing the Digital Video Recorder with the Multi-switcher, the following advantages – unavailable to

conventional systems using analog time-lapse VCRs – can be realized.

1. The Multi-switcher does not need to be operated when operating the Digital Video Recorder.

2. The Digital Video Recorder’s main menu screen or search screen can be easily displayed, facilitating

settings and search operations.

The combined Digital Video Recorder/Multi-switcher system is called a basic system in this manual.

Since the Multi-switcher has 2 VCR output terminals, hard disk space can be doubled by connecting two

Digital Video Recorders. This system is called an expansion system. The expansion system does not permit

the synchronization between the Digital Video Recorder and the Multi-switcher.

13.4.1. Basic System

Perform connections as shown in connection examples. (Refer to p. 43)

Set the Multi-switcher (C-MS91D and C-MS161D) and the Digital Video Recorder as follows:

• Multi-switcher settings

Perform remote and recording settings as follows:

• Digital Video Recorder settings

Perform communication settings as follows:

Setting Items

Contents

RS-232C

Setting Items

RS-232C

Contents

38400bps (Default)

Recording Pattern

Operation

Transmission Rate

RS-232C Flow Control

Switcher

Communication

Settings

Remote

Settings

RS-232C

OFF (Default)

Motion Detection

Pattern Operation

RS-232C

Synchronization*²

38.4kbps (Default)

1 (Default)

Recording Pattern

RS-232C Protocol

Recording Device

When perform-

ing Internal

Match the Recorder’s

settings to those of the

Multi-switcher

Recording

Settings

Motion Detection

Pattern

Timer Recording

settings

OFF*¹

Date/Time (VCR)

Buzzer/

Character

Display Settings

Note

*¹Use the Digital Video Recorder’s date/time display function for date/time display. If set at both the Multi-

switcher and Digital Video Recorder, characters overlap and cannot be seen clearly.

*²Recording Pattern, Motion Detection Pattern, Camera/ VCR mode selection, and Time Synchronization

switcher functions can all be controlled by the Digital Video Recorder. However, when syncronizing the

switcher's clock from the Recorder, set the Recorder's clock Time Synchronization setting to "MASTER."

Time synhronization cannot be performed if set to "SLAVE."

When only performing time synchronization, set the communication swither synchronization setting to

"TIME SYNC." Please note that in this mode Recording Pattern,Motion Detection Pattern, and Camera/

VCR mode selection functions cannot be controlled.

• For more information on the Multi-switcher’s settings, refer to the instruction manual for the Multi-switcher.

13.4.2. Expansion System (Series Recording)

Perform connections as shown in connection examples. (Refer to p. 44)

The Digital Video Recorder settings are as follows:

Setting Items

First Digital Video Recorder

Second Digital Video Recorder

Recording Mode

SERIES

MASTER

OFF

SERIES

SLAVE

Time Synchronization

Disk Full indicator status

• Operation

If the first Digital Video Recorder’s hard disk space becomes full, a signal is provided from the Disk Full Output

terminal. When the signal is received at the second Digital Video Recorder’s Recording Start Input terminal, its

Disk Full mode is reset, allowing recording to be started in the second unit.

Note

• Recording operation and Internal Timer Recording cannot be performed at the front panel of the Digital

Video Recorder set to Disk Full mode.

• Multi-switcher can be synchronized from the unit set to master through the RS-232C interface.Set

Communication Setting’s Switcher Synchronization to “TIME SYNC.”

Download from Www.Somanuals.com. All Manuals Search And Download.

14. CONNECTION EXAMPLES

14.1. Connection to the 24V AC or 12V DC or AC Mains Camera.

Note

Power Sync cameras cannot be used.

Camera

ALARM RESET OUT

ALARM IN

SW CTRL OUT

Sensor etc.

GND

ALARM RESET OUT

ALARM IN

TIME SYNC OUT

ALARM OUT

TIME SYNC IN

REC STOP IN

VIDEO

SW VIDEO

REC START IN

SW CTRL OUT

FAILURE OUT

ALARM RESET IN

DISK FULL OUT

OUT

OFF

AUDIO

OUT

GND

100BASE–TX

RS–232C

MAIN POWER

AC MAINS

1CH Digital Video Recorder

Monitor TV

Video Input

Download from Www.Somanuals.com. All Manuals Search And Download.

14.2. Connection to the Multi-switcher

14.2.1. Basic System (Combined with the C-MS91D Multi-switcher)

Note

Power Sync cameras cannot be used.

Camera

Sensor etc.

Camera

Video Input

1 – 9

Multi-switcher (C-MS91D)

VTR1

Alarm Input/Output

ALARM RESET OUT

ALARM IN

SW CTRL OUT

GND

D-Sub9 Pin

ALARM RESET OUT

ALARM IN

TIME SYNC OUT

ALARM OUT

TIME SYNC IN

REC STOP IN

VIDEO

SW VIDEO

REC START IN

SW CTRL OUT

FAILURE OUT

ALARM RESET IN

DISK FULL OUT

OUT

OFF

AUDIO

OUT

GND

100BASE–TX

RS–232C

MAIN POWER

AC MAINS

1CH Digital Video Recorder

Monitor TV

Video Input

Download from Www.Somanuals.com. All Manuals Search And Download.

14.2.2. Expansion System (Combined with the C-MS91D Multi-switcher)

Note

Power Sync cameras cannot be used.

Camera

Sensor etc.

Camera

Video Input

1 – 9

Multi-switcher (C-MS91D)

VTR1 VTR2

Alarm Output

GND

Monitor TV

1CH Digital Video Recorder (1)

Master

ALARM RESET OUT

ALARM IN

TIME SYNC OUT

TIME SYNC IN

VIDEO

SW VIDEO

REC STOP IN

REC START IN

ALARM OUT

SW CTRL OUT

FAILURE OUT

ALARM RESET IN

DISK FULL OUT

OUT

OFF

AUDIO

OUT

GND

100BASE–TX

RS–232C

MAIN POWER

AC MAINS

Switcher Video Output

ALARM RESET OUT

ALARM IN

TIME SYNC OUT

ALARM OUT

TIME SYNC IN

REC STOP IN

VIDEO

SW VIDEO

REC START IN

SW CTRL OUT

FAILURE OUT

ALARM RESET IN

DISK FULL OUT

OUT

OFF

AUDIO

OUT

GND

100BASE–TX

RS–232C

MAIN POWER

AC MAINS

Slave

1CH Digital Video Recorder (2)

Switcher Control

Output

Download from Www.Somanuals.com. All Manuals Search And Download.

15. RECORDING TIME TABLE

15.1. Recording Picture Quality Setting

The Digital Video Recorder is designed to be used as a hard disk recorder for surveillance applications, and

its picture quality can be set to Levels 1 – 5. Whether emphasis is placed on picture quality or on recording

interval can be selected depending on surveillance conditions. When setting the picture quality, carefully

consider recording times, recording intervals, recording types and other surveillance conditions, and be sure

to carry out test recordings in advance to ensure that the required picture quality is maintained.

Note: Recording time is given as a guideline reference.

15.2. When using the C-DR0100

Disk Mode : NORMAL

Audio Record : ON

Recording Time Intervals (Sec), Recording Time Period

1/60 1/30 1/15 1/10 1/5 1/3 1/2 10

97 158 227 409 681 878 1134 1460 1704 1803 1916

Picture

quality

File

Size

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

78 150 239 337 580 901 1112 1356 1631 1815 1884 1961

95 183 289 402 674 1011 1220 1450 1697 1855 1913 1976

84 124 234 364 498 804 1150 1352 1558 1769 1898 1943 1992

62 120 176 325 494 654 996 1334 1516 1684 1848 1942 1973 2008

Disk Mode : NORMAL

Audio Record : OFF

Recording Time Intervals (Sec), Recording Time Period

Picture

quality

File

Size

1/60 1/30 1/15 1/10 1/5 1/3 1/2

Level 1 64KB

Level 2 40KB

Level 3 32KB

Lebel 4 24KB

Level 5 16KB

51 103 171 257 513 1026 1539 2565 5131 10262 15392 30785

81 163 271 407 813 1627 2440 4067 8134 16268 24403 48805

67 101 202 337 505 1011 2021 3032 5053 10106 20212 30318 60637

89 133 267 445 667 1334 2668 4002 6670 13340 26680 40020 80041

65 131 196 392 654 981 1962 3924 5885 9809 19618 39236 58853 117707

15.3. When using the C-DR0101

Disk Mode : NORMAL

Audio Record : ON

Recording Time Intervals (Sec), Recording Time Period

1/60 1/30 1/15 1/10 1/5 1/3 1/2 10

67 100 195 315 454 818 1361 1755 2269 2919 3407 3605 3832

File

Size

Picture

quality

Level 1 64KB

Level 2 40KB

Level 3 32KB

Lebel 4 24KB

Level 5 16KB

53 105 155 300 478 674 1160 1803 2223 2711 3262 3630 3768 3922

65 129 191 365 577 804 1347 2021 2440 2900 3394 3711 3826 3953

86 168 247 468 729 996 1607 2300 2704 3117 3538 3795 3885 3984

64 124 240 351 651 988 1308 1991 2668 3032 3369 3695 3884 3947 4016

Disk Mode : NORMAL

Audio Record : OFF

Recording Time Intervals (Sec), Recording Time Period

Picture

quality

File

Size

1/5

205

325

1/60 1/30 1/15 1/10

1/3 1/2

342 513 1026 2052 3078 5131 10262 20523 30785 61570

1627 3254 4881 8134 16268 32537 48805 97610

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

68 103

54 108 163

542 813

67 135 202 404 674 1011 2021 4042 6064 10106 20212 40425 60637 121274

89 178 267

889 1334 2668 5336 8004 13340 26680 53360 80041 160081

1308 1962 3924 7847 11771 19618 39236 78471 117707 235413

534

785

65 131 262 392

Download from Www.Somanuals.com. All Manuals Search And Download.

Disk Mode : MIRRORING

Audio Record : ON

Recording Time Intervals (Sec), Recording Time Period

Picture

quality

File

Size

1/60 1/30 1/15 1/10 1/5 1/3 1/2

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

–

97 158 227 409 681 878 1134 1460 1704 1803 1916

78 150 239 337 580 901 1112 1356 1631 1815 1884 1961

95 183 289 402 674 1011 1220 1450 1697 1855 1913 1976

84 124 234 364 498 804 1150 1352 1558 1769 1898 1943 1992

62 120 176 325 494 654 996 1334 1516 1684 1848 1942 1973 2008

Disk Mode : MIRRORING

Audio Record : OFF

Recording Time Intervals (Sec), Recording Time Period

Picture

quality

File

Size

1/60 1/30 1/15 1/10 1/5 1/3 1/2

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

–

51 103 171 257 513 1026 1539 2565 5131 10262 15392 30785

81 163 271 407 813 1627 2440 4067 8134 16268 24403 48805

67 101 202 337 505 1011 2021 3032 5053 10106 20212 30318 60637

89 133 267 445 667 1334 2668 4002 6670 13340 26680 40020 80041

65 131 196 392 654 981 1962 3924 5885 9809 19618 39236 58853 117707

15.4. When using the C-DR0105

Disk Mode : NORMAL

Audio Record : ON

Recording Time Intervals (Sec), Recording Time Period

1/60 1/30 1/15 1/10 1/5 1/3 1/2 10

34 68 136 203 397 643 926 1670 2779 3583 4631 5959 6956 7360 7822

File

Size

Picture

quality

Level 1 64KB

Level 2 40KB

Level 3 32KB

Lebel 4 24KB

Level 5 16KB

54 108 213 316 612 976 1375 2368 3680 4539 5535 6658 7410 7693 8006

67 133 263 389 746 1179 1640 2751 4126 4982 5920 6930 7575 7811 8069

89 174 342 504 955 1488 2032 3281 4695 5520 6363 7224 7748 7932 8133

129 252 490 716 1328 2017 2670 4064 5447 6189 6877 7544 7928 8057 8199

Disk Mode : NORMAL

Audio Record : OFF

Recording Time Intervals (Sec), Recording Time Period

1/5

Picture

quality

File

Size

1/60 1/30 1/15 1/10

1/3 1/2

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

419

69 139 209

698 1047 2095 4190 6285 10475 20950 41900 62850 125701

55 110 221 332 664 1107 1660 3321 6642 9964 16606 33213 66427 99641 199282

68 137 275 412

90 181 363 544

133 267 534 801

1375 2063 4126 8253 12379 20632 41265 82531 123796 247593

1815 2723 5447 10894 16341 27235 55470 108941 163411 326823

2670 4005 8010 16020 24031 40051 80103 160207 240311 480622

825

1089

1602

Disk Mode : MIRRORING

Audio Record : ON

Recording Time Intervals (Sec), Recording Time Period

Picture

quality

File

Size

1/60 1/30 1/15 1/10 1/5 1/3 1/2

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

–

68 101 198 321 463 835 1389 1791 2315 2979 3478 3680 3911

54 106 158 306 488 687 1184 1840 2269 2767 3329 3705 3846 4003

66 131 194 373 589 820 1375 2063 2491 2960 3465 3787 3905 4034

87 171 252 477 744 1016 1640 2347 2760 3181 3612 3874 3966 4066

126 245 358 664 1008 1335 2032 2723 3094 3438 3772 3964 4028 4099

Disk Mode : MIRRORING

Audio Record : OFF

Recording Time Intervals (Sec), Recording Time Period

Picture

quality

File

Size

1/60 1/30 1/15 1/10 1/5 1/3 1/2

Level 1

Level 2

Level 3

Lebel 4

Level 5

64KB

40KB

32KB

24KB

16KB

–

69 104 209 349 523 1047 2095 3142 5237 10475 20950 31425

62850

99641

123796

163411

240311

55 110 166 332 553 830 1660 3321 4982 8303 16606 33213 49820

68 137 206 412 687 1031 2063 4126 6189 10316 20632 41265 61898

90 181 272 544 907 1361 2723 5447 8170 13617 27235 54470 81705

133 267 400 801 1335 2002 4005 8010 12015 20025 40051 80103 120155

Note

Setting the Disk Setting’s Disk Mode to "MIRRORING" limits the maximum recording interval to 1/30 second.

(Refer to p. 15;"Disk Setting.")

Download from Www.Somanuals.com. All Manuals Search And Download.

16. EXTERNAL TERMINAL SPECIFICATIONS

16.1. RS-232C Communication Specifications

The Digital Video Recorder’s RS-232C interface permits remote control using a connected PC.

Note

• Control software is not supplied as standard.

• Communication specifications are those set when the Switcher Synchronization selection on the

Communication Setting Screen is set to "OFF."

• TOA takes no responsibility for any inconvenience or damage to customer hardware or software which may

result from the use of control software based on the specifications described in this section.

16.1.1. The Rules of Overall Communications

1. All communications are established by means of a command from the controller.

2. Responses are always present in mutual communications.

3. The response timeout period is 1 second, and the timeout period between continuous data is 100

milliseconds. When the timeout occurs, the corresponding communications are regarded as failed.

4. Data is only updated when a communication setting content update command is received while in Standby

mode or in Idle and Recording Pause mode. No setting content update commands are accepted during

system activation, error message indication, menu screen display, search screen display, playback,

recording (Include Alarm Recording Setting’s Alarm is set to “VALID.”) or while in timer mode (DEL is

returned).

5. When command operation cannot be performed, received data is discarded and any commands are

regarded as invalid.

16.1.2. Communication Protocol

Transfer System :

Parity Bit :

Start/stop system (asynchronous system), duplex

Even

Transfer Rate :

Code :

9,600, 19,200, 38,400 bps

Binary code

Bit Length :

Flow Control :

Stop Bit :

8 bits

CTS/RTS handshaking, none

None

Error Control :

16.1.3. RS-232C Connector Pin Arrangement

The following table shows the signal name of each pin of the RS-232C D-sub 9P connector.

Pin No.

Signal Name

Unconnected

RXD (Received Data)

TXD (Transmitted Data)

Unconnected

GND

Unconnected

RTS (Request to send)

CTS (Clear to send)

Unconnected

Note: The plug for the RS-232C connector is not supplied with the Digital Video Recorder.

Use a cross cable for the RS-232C interface connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

16.1.4. RS-232C Communication Format (Controller

Digital Recorder)

Item

STX

LEN

COMMAND

PARA

DATA

ETX

No. of Byte

Variable

STX :

LEN :

Fixed to A0H.

The number of bytes from command to DATA

COMMAND : BT, MS, MV, LG, SE*¹

PARA :

DATA :

ETX :

Parameter*¹

DATA section (variable depending on a command and parameter)

Fixed to AFH.

*¹If communication data is transmitted, an ACK, NAK, or DEL signal is returned immediately after the data is

received.

ACK (06H) : Correct reception

NAK (15H) : Reception error

DEL (7FH) : Invalid operation

16.1.5. RS-232C Communication Command (Controller

Digital Recorder)

Commands are 2 bytes in length. Parameters (PARA) are also 2 bytes. They are followed by the multi-byte

DATA section. If DATA LEN is "0," no DATA section follows.

Key's Commands

PARA

DATA LEN

Command

Operation

Playback Key

Playback Stop Key

Reverse Playback Key

Pause Key

Recording Key

Buzzer Stop Key

Menu Key (Press Menu Key for 1 second or more)

Start Internal Timer Recording (Press Timer key for 1 second or more)

Standby Key ON

Standby Key OFF

Search Key

Periodical Status Inquiry (Response returned)

Alarm Operation

Recording Stop Key (Press Recording Key for 1 second or more)

Recording Start Operation

Up Shift Key

Down Shift Key

– Key

+ Key

Select Key

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Setting Commands

Command

Contents

General Recording Setting Picture

Quality

Operation

DATA LEN

PARA

0 – 4 (Level 5 – Level 1)

0 : OFF, 1 : ON

General Recording Setting Audio

General Recording Setting Recording 0:1/60, 1:1/30, 2:1/15, 3:1/10, 4:1/5, 5:1/3, 6:1/2, 7:1, 8:2, 9:3, A:5,

Interval

B:10, C:20, D:30, E:60

Switcher Control Period

Setting Frame No.

Timer Setting Mode

Date

0 – 9 (1,2,3,4,5,10,15,20,30,60)

0 – 9: Setting No.01 – 10

0:Cancel, 1:Daily, 2:Weekly

First byte MM:1 – C, Second byte DD:1 – 1F

BIT0:Sun, BIT1:Mon, BIT2:Tue, BIT3:Wed, BIT4:Thu, BIT5:Fri,

BIT6:Sat

Day of the week

Timer Start Time

Timer End Time

First byte HH:0 – 17, Second byte MM:0 – 3B

0 – 4 (Level 5 – Level 1)

Internal Timer Recording Setting

Picture Quality

Internal Timer Recording Setting

Audio

0:OFF, 1:ON

Internal Timer Recording Setting

Recording Interval

Recording Pattern

0:1/60, 1:1/30, 2:1/15, 3:1/10, 4:1/5, 5:1/3, 6:1/2, 7:1, 8:2, 9:3, A:5,

B:10, C:20, D:30, E:60

0:1, 1:2

Motion Detection Pattern

Alarm Setting

Alarm Input Mode

0:1, 1:2

0: Invalid, 1:Valid, 2:Valid during recording (Val Rec)

0:Edge, 1:Level

Pre-Alarm Period

Alarm Recording Period

0 – 7 (0Sec, 10Sec, 15Sec, 20Sec, 30Sec, 1Min, 2Min, 5Min)

0 – 9 (10Sec, 15Sec, 20Sec, 30Sec, 1Min, 2Min,, 3Min, 4Min, 5Min,

10Min)

Post-Alarm Period

0 – 7 (0Sec, 10Sec, 15Sec, 20Sec, 30Sec, 1Min, 2Min, 5Min)

0 – 4 (Level 5 – Level 1)

0:OFF, 1:ON

Alarm Recording Picture Quality

Alarm Recording Audio

Alarm Recording Recording Interval

Buzzer Sound Output

0:1/60, 1:1/30, 2:1/15, 3:1/10, 4:1/5, 5:1/3, 6:1/2, 7:1

0:OFF, 1:ON

Alarm Output Period

Disk Mode (C-DR0101, C-DR0105)

Recording Mode

0:During Alarm Recording, 1:1Second

0:Nomal, 1:Mirroring

0:Stop, 1:Re-Rec, 2:Series

Date/Time Setting Year

Date/Time Setting Month

Date/Time Setting Date

Date/Time Setting Hour

Date/Time Setting Minute

Date/Time Setting Sec

Picture Quality Display

Audio ON/OFF Display

Re-Recording Mode

YYYY:7D0 – 833 (2000 – 2099 Year)

MM: 1 – C (Jan – Dec Month)

DD: 1 – 1F (1 – 31 Date)

HH: 0 – 17 (00:00 – 23:00 Hour)

MM: 0 – 3B (0 – 59 Minute)

SS: 0 – 3B (0 – 59 Second)

0: Hide, 1:Display

Recording Mode Display

Playback Display

Remaining Time Display

Disk Mode set to Nomal : 0:Hide, 1:Display

Disk Mode set to Mirroring: 0:Hide, 1:Max, 2:Min, 3:HDD-A, 4:HDD-B

0: Hide, 1:Display

Date Display

Time Display

Date/Time Display Position

0: Hide, 1:Display

0:Upper Left, 1: Upper Center, 2:Upper Right, 3: Lower Left,

4: Lower Center, 5: Lower Right

0: Hide, 1:Display

Disk Mode Indication

(C-DR0101, C-DR0105)

Communication Rate

Flow Control

0: 9600, 1: 19200, 2: 38400 bps

0:OFF, 1:ON

0:Master, 1:Slave

Time Synchronization

Synchronized Time

0 – 23

Switcher Synchronization

Playback Mode

0:OFF, 1:ON, 2:Time Sync

0:All, 1:HDD-A, 2:HDD-B

0:Disallow, 1:Allow

Simultaneous Recording/Playback

Summer Time Setting

0:OFF, 1:ON

Summer Time First day Month

Summer Time First day Sunday

Summer Time First day Time

Summer Time Last day Month

Summer Time Last day Sunday

Summer Time Last day Time

1 – C:Jan – Dec Month

1:Fast, 2:Second, 3:Third, 4:Fourth, 5:Last

0 – 17:00 – 23 Hour

1 – C:Jan – Dec Month

1:Fast, 2:Second, 3:Third, 4:Fourth, 5:Last

0 – 17:00 – 23 Hour

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Setting Content Request Command

Command

Contents

General Recording Setting Picture

Quality

Operation

Request to send setting contents

DATA LEN

PARA

General Recording Setting Audio

General Recoding Setting Recording

Interval

Request to send setting contents

0 – 9: Setting No., Request to send setting contents

Request to send setting contents

Request to send setting contents (current time)

Request to send setting contents

Switcher Control Period

Timer Setting Data

Alarm Setting

Alarm Input Mode

Pre-Alarm Period

Alarm Recording Period

Post-Alarm Period

Alarm Recording Picture Quality

Alarm Recording Audio

Alarm Recording Recording Interval

Buzzer Sound Output

Alarm Output Period

Disk Mode (C-DR0101, C-DR0105)

Recording Mode

Clock Setting Data

Picture Quality Display

Audio Display

Recording Mode Display

Recording Display

Playback Display

Remaining Time Display

Daily Display

Time Display

Date/Time Display Position

Disk Mode Indication (C-DR0101,C-DR0105)

Transmission Rate

Flow Control

Time Synchronization

Synchronized Time

Switcher Synchronization

Playback Mode

Playback during Recording

Summer Time Setting

Summer Time First day Month

Summer Time First day Sunday

Summer Time First day Time

Summer Time Last day Month

Summer Time Last day Sunday

Summer Time Last day Time

Log Request Command

Contents

Request for Recording Log

Operation

Request for sending from the head of the most recent data

Request for continued data

Command PARA DATA LEN

Next Request for Recording Log

Request for Alarm Recording Log

Next Request for Alarm Recording Log

Request for Failure Logs

Request for sending from the head of the most recent data

Request for continued data

Request for sending from the head of the most recent data

Request for continued data

Next Request for Failure Logs

Search Menu Execution Command

Command

Contents

Date/Time Search Year

Date/Time Search Month

Date/Time Search Date

Date/Time Search Hour

Date/Time Search Minute

Operation

PARA

DATA LEN

YYYY: 7D0 – 833

(2000 – 2099 Year)

MM: 1 – C (Jan – Dec Month)

DD: 1 – 1F (1 – 31 Date)

HH: 0 – 17 (00:00 – 23:00 Hour)

MM: 0 – 3B (0 – 59 Minute)

Note: Date/Time search is performed using setting data.

Download from Www.Somanuals.com. All Manuals Search And Download.

16.1.6. RS-232C Communication Format (Digital Recorder

Controller)

COMMAND

PARA

DATA

ETX

Item

STX

LEN

No. of Byte

Variable

STX : Fixed to A0H.

LEN : The number of bytes from command to DATA

COMMAND : BT, MV, LG

PARA :

DATA :

ETX :

Parameter

DATA section (variable depending on a command and parameter)

Fixed to AFH.

16.1.7. RS-232C Communication Command (Digital Recorder

Controller)

Commands are 2 bytes in length. Parameters (PARA) are also 2 bytes. They are followed by the multi-byte

DATA section.

Key response command

Command PARA DATA LEN

Contents

Operation Status

Status

Operation

0:Power OFF, 1:Power ON

0:Standby or Stop

1:Pause

2:Playback

3:Fast Forward Playback

4 Reverse Playback

5:Rewind

6.Menu or Search Screen Display

7:Disk Error or disk operation such as disk recognition

0:Standby or Stop

Recording Status

Failure

1:Recording

2:Alarm Recording

3:Internal Timer Recording

0: No failure

1: Hard disk failure

2: Video loss failure

3: Fan failure

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Setting Content Response Command

Command

Contents

General Recording Setting Picture

Quality

Operation

DATA LEN

PARA

0 – 4 (Level 5 – Level 1)

0 : OFF, 1 : ON

General Recording Setting Audio

General Recording Setting Recording 0:1/60, 1:1/30, 2:1/15, 3:1/10, 4:1/5, 5:1/3, 6:1/2, 7:1, 8:2, 9:3, A:5,

Interval

B:10, C:20, D:30, E:60

Switcher Control Period

Setting Frame No.

Timer Setting Mode

Date

0 – 9 (1,2,3,4,5,10,15,20,30,60)

0 – 9: Setting No.01 – 10

0:Cancel, 1:Daily, 2:Weekly

First byte MM:1 – C, Second byte DD:1 – 1F

BIT0:Sun, BIT1:Mon, BIT2:Tue, BIT3:Wed, BIT4:Thu, BIT5:Fri,

BIT6:Sat

Day of the week

Timer Start Time

Timer End Time

First byte HH:0 – 17, Second byte MM:0 – 3B

0 – 4 (Level 5 – Level 1)

Internal Timer Recording Setting

Picture Quality

Internal Timer Recording Setting

Audio

0:OFF, 1:ON

Internal Timer Recording Setting

Recording Interval

Recording Pattern

0:1/60, 1:1/30, 2:1/15, 3:1/10, 4:1/5, 5:1/3, 6:1/2, 7:1, 8:2, 9:3, A:5,

B:10, C:20, D:30, E:60

0:1, 1:2

Motion Detection Pattern

Alarm Setting

Alarm Input Mode

0:1, 1:2

0: Invalid, 1:Valid, 2:Valid during recording (Val Rec)

0:Edge, 1:Level

Pre-Alarm Period

Alarm Recording Period

0 – 7 (0Sec, 10Sec, 15Sec, 20Sec, 30Sec, 1Min, 2Min, 5Min)

0 – 9 (10Sec, 15Sec, 20Sec, 30Sec, 1Min, 2Min,, 3Min, 4Min, 5Min,

10Min)

Post-Alarm Period

0 – 7 (0Sec, 10Sec, 15Sec, 20Sec, 30Sec, 1Min, 2Min, 5Min)

0 – 4 (Level 5 – Level 1)

0:OFF, 1:ON

Alarm Recording Picture Quality

Alarm Recording Audio

Alarm Recording Recording Interval

Buzzer Sound Output

0:1/60, 1:1/30, 2:1/15, 3:1/10, 4:1/5, 5:1/3, 6:1/2, 7:1

0:OFF, 1:ON

Alarm Output Period

Disk Mode (C-DR0101, C-DR0105)

Recording Mode

0:During Alarm Recording, 1:1Second

0:Nomal, 1:Mirroring

0:Stop, 1:Re-Rec, 2:Series

Date/Time Setting Year

Date/Time Setting Month

Date/Time Setting Date

Date/Time Setting Hour

Date/Time Setting Minute

Date/Time Setting Sec

Picture Quality Display

Audio ON/OFF Display

Re-Recording Mode

YYYY:7D0 – 833 (2000 – 2099 Year)

MM: 1 – C (Jan – Dec Month)

DD: 1 – 1F (1 – 31 Date)

HH: 0 – 17 (00:00 – 23:00 Hour)

MM: 0 – 3B (0 – 59 Minute)

SS: 0 – 3B (0 – 59 Second)

0: Hide, 1:Display

Recording Mode Display

Playback Display

Remaining Time Display

Disk Mode set to Nomal : 0:Hide, 1:Display

Disk Mode set to Mirroring: 0:Hide, 1:Max, 2:Min, 3:HDD-A, 4:HDD-B

0: Hide, 1:Display

Date Display

Time Display

Date/Time Display Position

0: Hide, 1:Display

0:Upper Left, 1: Upper Center, 2:Upper Right, 3: Lower Left,

4: Lower Center, 5: Lower Right

0: Hide, 1:Display

Disk Mode Indication

(C-DR0101, C-DR0105)

Communication Rate

Flow Control

0: 9600, 1: 19200, 2: 38400 bps

0:OFF, 1:ON

0:Master, 1:Slave

Time Synchronization

Synchronized Time

0 – 23

Switcher Synchronization

Playback Mode

0:OFF, 1:ON, 2:Time Sync

0:All, 1:HDD-A, 2:HDD-B

0:Disallow, 1:Allow

Simultaneous Recording/Playback

Summer Time Setting

0:OFF, 1:ON

Summer Time First day Month

Summer Time First day Sunday

Summer Time First day Time

Summer Time Last day Month

Summer Time Last day Sunday

Summer Time Last day Time

1 – C:Jan – Dec Month

1:Fast, 2:Second, 3:Third, 4:Fourth, 5:Last

0 – 17:00 – 23 Hour

1 – C:Jan – Dec Month

1:Fast, 2:Second, 3:Third, 4:Fourth, 5:Last

0 – 17:00 – 23 Hour

Download from Www.Somanuals.com. All Manuals Search And Download.

Log Content Response Command

Operation

Request for sending from the head of the most recent data

Request for continued data

Contents

Request for Recording Log

Command PARA DATA LEN

Next Request for Recording Log

Request for Alarm Recording Log

Next Request for Alarm Recording Log

Request for Failure Logs

Request for sending from the head of the most recent data

Request for continued data

Request for sending from the head of the most recent data

Request for continued data

Next Request for Failure Logs

Shown below are log information DATA section (13 bytes) formats.

DATA LEN

Contents

Data valid/invalid

Year

Description of Data

0: Invalid, 1: Valid

YYYY: 7D0 – 833 (2000 – 2099 Year)

MM: 1 – C (Jan – Dec Month)

DD: 1 – 1F (1 – 31 Date)

Month

Date

Time

HH: 0 – 17 (00:00 – 23:00 Hour)

MM: 0 – 3B (0 – 59 Minute)

SS: 0 – 3B (0 – 59 Second)

Minute

Second

Detailed Code

RD/RQ mode:

0: Recording Start, 1:Recording End, 2:Internal Timer Recording Start,

3: Internal Timer Recording End

AL/AQ mode: 0: Alarm Recording Start, 1: Alarm Recording End

TR/TQ mode: 65 – C8 Video Failure, C9 – 12C: HDD Failure, 12D: Fan Failure

FE:DATA follows, FF: No DATA follows

Continuation sign

When transmitting log data, DATA contained in LEN (up to 255 bytes) is set in 13-byte units. If DATA’s 13th

byte is a continuation sign (0xFE), DATA follows. If last DATA is a continuation sign, a continued log

acquisition command becomes valid. Transmission format and transmitting/receiving sequence are as follows:

...........

Item

STX

LEN

COMMAND PARA

DATA

ETX

...........

No. of Byte

Unit

Host

Request for recording log

Transmission of recording log (DATA follows)

Request for next recording log

Transmission of next recording log (DATA follows)

Request for next recording log

Transmission of next recording log (No DATA follows)

Search menu result command

Command PARA DATA LEN

Contents

Operation

0 : No corresponding Data is present.

1 : Corresponding Data is present.

Time Search

Execution Result

Note

This response is transmitted to a controller when an ACK signal has been returned in response to a SE

command.

16.2. About the Ethernet Terminal

The Digital Video Recorder is equipped the Ethernet terminal (100BASE-TX). Use the LAN (crossing) cable to

connect the Ethernet terminal to the PC.

Download from Www.Somanuals.com. All Manuals Search And Download.

17. RACK MOUNTING

Use the optional MB-15B Rack Mounting Bracket when mounting the Digital Video Recorder in an equipment

rack. Remove 4 rubber feet on the bottom surface by loosening their respective fixing screws with a standard

screwdriver.

S^Z

T^Z

3 x 14 mm tapping screw

(supplied with the MB-15B)

5 x 12 mm rack mounting screw

(supplied with the MB-15B)

MB-15B (optional)

M5 fiber washer

(supplied with the MB-15B)

Note

• Use the Digital Video Recorder in locations with ambient temperature of between +5°C and +40°C

• Be sure to mount the Digital Video Recorder below the heat generating components, and mount the

perforated panel between the Recorder and such a heat generating component as required.

• The Digital Video Recorder has a built-in cooling fan. Never block the Recorder’s ventilation slot.

• Avoid installing the Digital Video Recorder in locations exposed to vibration.

Download from Www.Somanuals.com. All Manuals Search And Download.

18. IF YOU THINK THERE IS A FAILURE: (TROUBLESHOOTING)

Symptom

Possible Cause

Remedy

Cannot switch on the power.

• The supplied power cord is not • Connect the power cord.

connected to the Digital Video Recorder’s

Power inlet and wall AC outlet.

Cannot operate the front panel-

mounted keys.

• Keys are locked.

• Release Key Lock.

No picture is displayed.

• Power is not switched on.

• Cables are not correctly connected.

• Switch on the power.

• Connect the cable correctly.

The Recorder is not activated

even if the Standby key is

pressed.

• Main power is not switched on.

• Switch on the main power.

The Recorder is not terminated

even if the Standby key is

pressed.

• The Standby key is not continuously • Hold down the Standby key for 1

pressed for 1 second or more. second or more.

Cannot record.

• Recording mode is set to "STOP" and • Change the Overwrite Recording

no available hard disk time remains.

setting to "RE-REC" or "SERIES."

Cannot stop recording.

• Key Lock is set to ON.

• Reset Key Lock

Cannot perform Internal Timer

recording.

• The Recorder is in General recording • Stop General recording and press the

mode.

• Incorrect timer setting.

• Recording mode is set to "SERIES."

Timer key.

• Set timer operating times correctly.

• Change the Recording mode to

"STOP" or "RE-REC."

Cannot perform Alarm

recording.

• Alarm input cord not correctly • Connect cords correctly.

connected.

• Alarm not set to "VALID."

• Set the Alarm setting to "VALID."

No voice or sound recorded.

• Each Recording Mode Audio Setting • Set Audio setting to "ON."

selection not set to ON.

Cannot perform search and

playback.

• Hard disk is initialized.

• Not recorded on the hard disk.

• Playback during Recording is set to

"OFF."

• Search and playback cannot be

performed without recording data.

Perform recording.

• Playback cannot be performed during

recording. Set the Playback during

Recording selection to "ON"

No screen indication displayed.

On-screen time is not accurate.

• Display setting set to "HIDE."

• Time not adjusted.

• Set Display setting to "DISP."

• Adjust times.

• Power was switched off for a long period • If no main power is supplied

of time.

continuously for 30 days or more,

clock data will be lost. In such cases,

update times again.

System failure indicator does not • Check to confirm the contents of failure • Remove the cause of the failure.

extinguish.

log (refer to p. 25).

The indication "Disk may have

failed" is displayed on the

screen.

• Hard disk format data may have been • If the situation cannot be improved,

damaged.

contact your TOA dealer.

• Hard disk may have failed. Referring to

p. 28; "When the Failure Screen is

displayed," check the symptom.

Download from Www.Somanuals.com. All Manuals Search And Download.

19. SPECIFICATIONS

* 0dB = 1V

Model

C-DR0100

C-DR0101

C-DR0105

Power Source

110 – 120 V AC 50/60 Hz

24 W (450 mA)

Power Consumption

Image Compression

System

35 W (640 mA)

37 W (670 mA)

Motion JPEG

Recording Medium

E-IDE Hard Disk

120 GB (120 GBx 1)

240 GB (120 GBx 2)

500 GB (250 GBx 2)

Video Input

1 Input VBS1.0 V(p-p), 75Ω, BNC

Video Output

Front: 1 Output VBS1.0V(p-p), 75Ω, RCA pin jack

Rear: 1 Output VBS1.0V(p-p), 75Ω, BNC

1 Input VBS1.0V(p-p), 75Ω, BNC

Switcher Video Input

Switcher Video Output

Audio Recording

System

1 Output VBS1.0V(p-p), 75Ω, BNC

8 bits, Linear PCM, sampling frequency: 16 KHz

Audio Input

1 Input, –10 dB*, 10 kΩ, RCA pin jack

Front: 1 Output, –10 dB*, 600 Ω, RCA pin jack

Rear: 1 Output, –10 dB*, 600 Ω, RCA pin jack

300 – 6,000 Hz

Audio Output

Frequency Response

Alarm Input

1 Input (EDGE, LEVEL), no-voltage make contact input, open voltage: 2 VDC,

short-circuit current: 0.5 mA, loop resistance: under 100Ω, screwless connector

1 output, open collector output, withstand voltage: 30 VDC, control current : 20 mA,

screwless connector

Alarm Output

Picture Quality

Changeable in 5 steps, File size: 64 KB (LEVEL1), 40 KB (LEVEL2), 32 KB (LEVEL3),

24 KB (LEVEL4), 16 KB (LEVEL5)

Pixels

720 x 240 (fixed)

Recording Intervals

Pre-Alarm Recording

Alarm Recording

Post Alarm Recording

Date/Time

15 steps (1/60, 1/30, 1/15, 1/10, 1/5, 1/3, 1/2, 1, 2, 3, 5, 10, 20, 30, 60 sec)

0 sec, 10 sec, 15 sec, 20 sec, 30 sec, 1 min, 2 min, 5 min

10 sec, 15 sec, 20 sec, 30 sec, 1 min, 2 min, 3 min, 4 min, 5 min, 10 min (Edge mode)

0 sec, 10 sec, 15 sec, 20 sec, 30 sec, 1 min, 2 min, 5 min (Level mode)

Year/ month/ date/ hour/ minute/ sec, 24-hours format display, monthly deviation of within

±30 seconds (25°C), can be operated until the leap year 2099, summer time settings

10 independent programs (date, daily, weekly, designated day-of-the-week)

recording interval, start and end times, picture quality, and audio on-off can be set.

Date/Time search, Block search, Time Shift search

Internal Timer

Recording

Search Function

System Failure Output

1 output (HDD failure, Video loss, Fan failure) open collector output

withstand voltage: 30 VDC, control current: 20 mA, screwless connector

alarm reset, recording start, recording stop, clock synchronization

no-voltage make contact input, open voltage: 2 VDC, short-circuit current: 0.5 mA, loop

resistance: under 100 Ω, screwless connector

Control Input Terminal

Control Output Terminal alarm reset, clock synchronization, disk full : open collector output,

withstand voltage: 30 VDC, control current: 20 mA, screwless connector

switcher control: TTL level negative logic pulse, pulse width over 17 ms, screwless

connector

Communication

Function

RS-232C (External control function) D-sub connector (9 pin, male)

100 BASE-TX Ethernet terminal

Memory Backup

Operating Temperature

Operating Humidity

Finish

720 hours (fully charged), clock data retention

+5°C to +40°C

Under 80% RH (no dew condensation)

Panel: Aluminum extrusion, black, 30% gloss

Case: Surface treated steel plate, black, 30% gloss

420 (W) x 53.8 (H) x 331 (D) mm

Dimensions

Weight

4.5 kg

5.3 kg

Accessories

Optional Equipment

Power supply cord (2 m) … 1

Rack mounting bracket: MB-15B

Note: The Digital Video Recorder’s specifications and external designs are subject to change without notice.

Printed in Japan

133-12-914-0B

Download from Www.Somanuals.com. All Manuals Search And Download.

Technicolor Thomson Universal Remote DTH614 User Manual
Toshiba Computer Monitor P1550LA User Manual
Toshiba Printer B 570 User Manual
Tote Vision Computer Monitor LCD 841SDI User Manual
Trane Air Conditioner Unit Control Module UCM 42 Retrofit Model VAV User Manual
TRENDnet Computer Drive TBW 105UB User Manual
Troy Bilt Chipper 070 User Manual
ViewSonic Projector PJ658 User Manual
Vox Musical Instrument Amplifier TB35C1 User Manual
Wayne Septic System 330502 001 User Manual