Tecumseh Fan OH195EA User Manual

Operator’s Manual

OH195EA/OH195XA

OH195EP/OH195XP

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Table of Contents

Safety Definitions..............................................................................ii

I. General Safety Precautions............................................................. 1

II. How to Get Service.......................................................................... 3

III. Oil and Fuel Specifications............................................................... 3

IV. Before Starting Your Engine............................................................. 4

V. Starting Your Engine ........................................................................ 6

VI. Stopping Your Engine and Short-Term Storage ............................. 10

VII. Maintenance .................................................................................. 10

VIII. Transporting Your Engine............................................................... 13

IX. Storing Your Engine ....................................................................... 14

X. Preventing Forest, Brush and Grass Fires..................................... 16

XI. Maintenance Intervals.................................................................... 16

California & US EPA Emission Control Warranty Statement.......... 20

Emission Control System Warranty ............................................... 21

XII. Warranty Information...................................................................... 22

Visit our web site at www.TecumsehPower.com

Maintenance Tips

Parts Look-Up System

Great Tecumseh Apparel

Nearest Authorized Tecumseh Servicing Dealer Location

181-1032-14

(English) 10/01/06

Download from Www.Somanuals.com. All Manuals Search And Download.

• NEVER fill fuel tank indoors. Fill fuel tank outdoors

in a well-ventilated area.

I. General Safety Precautions

• DO NOT smoke while refueling tank.

! WARNING

• Use only an approved red GASOLINE container to

store and dispense fuel. Tecumseh recommends

purchasing gasoline in containers with a capacity of

2.5 gallons or less. Small containers are easier to

handle and help eliminate spillage during refueling.

Read equipment manufacturer’s manual and this

material thoroughly before using this engine. Failure to

do so can result in serious injury or death. Call Tecumseh

Power Company at 1-800-558-5402 or visit

www.TecumsehPower.com if you have any questions.

• DO NOT pour fuel from engine or siphon fuel by

mouth. To empty fuel tank see "I. Draining Fuel"

instructions on page 14.

A. Avoid Carbon Monoxide Poisoning

All engine exhaust contains

carbon monoxide, a deadly

gas. Breathing carbon

C. Adult Supervision of Operation, Refueling

and Maintenance

monoxide can cause

headaches, dizziness,

The manufacturer of the application may provide

information about who is allowed to use this engine (see

equipment manufacturer’s manual). Not everyone who is

allowed to use this engine is capable of safely and

responsibly operating, maintaining and/or fueling it.

Tecumseh recommends the following:

drowsiness, nausea, confusion

and eventually death.

Carbon monoxide is a colorless, odorless, tasteless gas

which may be present even if you do not see or smell any

engine exhaust. Deadly levels of carbon monoxide can

collect rapidly and you can quickly be overcome and

unable to save yourself. Also, deadly levels of carbon

monoxide can linger for hours or days in enclosed or

poorly-ventilated areas. If you experience any symptoms of

carbon monoxide poisoning, leave the area immediately,

get fresh air, and SEEK MEDICAL TREATMENT.

• An adult should fuel this engine. NEVER allow

children to refuel this engine. See "C. Filling Fuel

Tank" instructions on page 5.

• An adult should perform maintenance on this

engine. See "VII. Maintenance" instructions on page

10. Only allow children to perform maintenance if an

adult has determined they are experienced and

capable of such operation.

To prevent serious injury or death from carbon monoxide:

• An adult should start the engine. See "G. Avoid

Accidental Starts" instructions on page 2. Only allow

children to start the engine if an adult has

determined they are experienced and capable of

such operation.

• NEVER run engine indoors. Even if you try to

ventilate engine exhaust with fans or open windows

and doors, carbon monoxide can rapidly reach

dangerous levels.

• NEVER run engine in poorly ventilated or partially

enclosed areas such as barns, garages,

basements, carports, under dwellings, or in pits.

To avoid unsupervised operation of the engine, especially

by children, NEVER leave it unattended when it is running.

• NEVER run engine outdoors where engine exhaust

can be drawn into a building through openings such

as windows and doors.

D. Stay Away from Rotating Parts

NEVER operate the engine with an unguarded engine

shaft. See Figure 1, on page 2.

B. Avoid Gasoline Fires

The equipment manufacturer may

attach a sprocket and chain or pulley

and belt to the engine shaft. If these

parts are not properly guarded, or if you

are not sure whether they are properly

guarded, DO NOT use your engine;

contact the equipment manufacturer.

Hands, feet, hair, jewelry, clothing, etc.

can become entangled in rotating parts,

leading to serious injury or death. To

avoid serious injury or death, be sure the

flywheel guard is in place.

Gasoline (fuel) vapors are highly flammable

and can explode. Fuel vapors can spread

and be ignited by a spark or flame many feet

away from engine. To prevent injury or death

from fuel fires, follow these instructions:

• NEVER store engine with fuel in fuel tank inside a

building with potential sources of ignition such as

hot water and space heaters, clothes dryers,

electric motors, etc.

• NEVER remove fuel cap or add fuel when engine is

running.

See Figures 1and 2, on page 2.

• NEVER start or operate the engine with the fuel fill

cap removed.

• Allow engine to cool before refueling.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 1

E. Do Not Modify Engine

To avoid serious injury or death, DO NOT modify engine in

any way. Tampering with the governor setting can lead to a

runaway engine and cause it to operate at unsafe speeds.

NEVER tamper with factory setting of engine governor.

! WARNING

Use of this engine on fun-carts, go-karts, or mini-bikes

can result in serious injury or death. Tecumseh

manufactures the Power Sport line of engines for use in

such applications. Consult your local Authorized

Tecumseh Servicing Dealer, call 1-800-558-5402, or go

to www.TecumsehPower.com for additional information.

Figure 1. DO NOT use Without Engine Shaft Guard

F. Avoid Burns and Fire from Hot Surfaces

The muffler and other engine parts become

extremely hot during operation and remain

hot after the engine has stopped.

• To avoid severe burns on contact,

NEVER operate the engine without

the muffler guard in place, see

Figure 2 and avoid hot areas of the

engine.

• To reduce the risk of fire keep all materials that can

burn, including grass and leaves, away from muffler

and rest of engine. DO NOT operate, idle or park

the engine application in long dry grass or other dry

ground cover.

1. Muffler Guard

2. Flywheel Guard

G. Avoid Accidental Starts

To prevent accidental starting when working on equipment

always:

Figure 2. Typical Engine Guard Locations

• Disconnect spark plug wire and keep it away from

spark plug. See Figures 3 and 4.

• Keep the disconnected spark plug wire

securely away from metal parts where arcing

could occur.

• Attach the spark plug wire to the grounding

post, if provided.

• Disconnect battery at negative terminal first, if

engine is equipped with an electric starter.

Figure 3. Disconnecting/Connecting Spark Plug

• Turn off all engine switches.

• Remove ignition key, if provided.

H. Use Hearing Protection

Engine noise may cause hearing damage. Always wear

hearing protection when operating an engine.

Figure 4. Typical Spark Plug Connection

Page 2

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

II. How to Get Service

2083

For engine adjustments, repairs or warranty service not

covered in this manual, contact your nearest Authorized

Tecumseh Servicing Dealer. Find them on our website at

www.TecumsehPower.com or call Tecumseh Power

Company at 1-800-558-5402.

TECUMSEH POWER COMPANY

THIS ENGINE MEETS 1995-2005 CALIF & US EPA

PHI APPLICABLE EMISSION REGULATIONS FOR SI

SORE ENGINES

Visit our web site at www.TecumsehPower.com

Maintenance Tips

Parts Look-Up System

Great Tecumseh Apparel

Nearest Authorized Tecumseh Servicing Dealer Location

LV195EA

361540D

04015AA0001

195

4TPXS.1951BB

A. Engine Identification Decal

ENGINE

MODEL:

A sample engine identification decal (See Figure 5.)

indicates the engine’s model number, specification of

engine and the date of manufacture (D.O.M.). Please look

at the decal on your engine and fill in this information in the

spaces provided for future reference.

SPEC:

D.O.M.:

The engine identification decal also includes engine life

specifications for the emissions-related useful life period of

your engine. This period relates to the emission compliance

life as certified by EPA and/or CARB. To find the life period

specification for your engine, please look on your engine’s

decal and find the letter enclosed by quotation marks

between the words MODERATE and LIFE PERIOD. Match

one of the following letters with the letter printed on your

decal. For example, OH models are designated as “C” 125

hours, “B” 250 hours, and “A” 500 hours.

Figure 5. Engine Identification Label

TECHNICIAN'S HANDBOOK

B. Tecumseh Technician’s Handbooks

If you have a general understanding of internal combustion

engines and wish to repair and service your engine and/or

engine emission control systems yourself, a Technician’s

Handbook is available from your Authorized Tecumseh

Servicing Dealer. See Figure 6. This handbook covers

repairs and adjustments not covered within this Operator’s

Manual, and it is intended for individuals who have had

adequate training, experience and who practice proper tool

usage. Service procedures should be clearly understood

and practiced when servicing Tecumseh Engines. Order as

part no. 695244A for OH models.

4 -CYCLE

OVERHEAD VALVE

ENGINES

Tecumseh manufactures and is responsible only for the

engine used on this power equipment. If repair or service is

needed for anything other than the engine, contact the

service source recommended by the equipment

manufacturer.

Figure 6. Technician’s Handbook

Table 1. Recommended Engine Oil

III. Oil and Fuel Specifications

Tecumseh Recommended Oil Usage

Straight Grade

Tecumseh Part No.

730225A or SAE 30

A. Oil

To operate engine you need to use a clean, high quality,

detergent oil. For recommended engine oil, See Table 1.

Multi Grade

Tecumseh Part No.

730226A or SAE 5W30 or SAE 10

NOTES

Be sure original container is marked A.P.I. Service “SL/SJ”.

Synthetic

Tecumseh Part No.

730263 or SAE 0W30

20^OF

32^OF

0^OC

80^OF

Using multigrade oil above 32°F (0°C) will increase oil

consumption. SAE10W40 is not recommended.

100 F

-20 F

0^OF

40^OF

60^OF

10^OC

20^OC

30^OC

40^OC

-30 C

-20 C

-10 C

The oil sump capacity is 21 ounces or 1-1/4 U.S. Pints

(.62 liters).

Tecumseh special-formulated oils are available at your

Authorized Tecumseh Servicing Dealer.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 3

Table 2. Recommended Fuel

B. Fuel

Use unleaded regular, unleaded premium or reformulated

automotive fuel only. You may use gasoline containing the

following components identified in Table 2.

Fuel Component

Percentage

Ethanol

10%

15%

• DO NOT use leaded fuel.

Grain Alcohol (“Gasohol”)

• Fuel must be fresh and clean. NEVER use fuel left

over from last season or stored for long periods.

MTBE (Methyl Tertiary Butyl Ether)

ETBE (Ethyl Tertiary Butyl Ether)

• NEVER mix oil with fuel.

• DO NOT use fuel containing Methanol (Wood

Alcohol).

The use of alternative fuels such as E85

CAUTION

or E20 are not recommended for use in

Fill between “Full”

and “ADD” Marks

FULL

Tecumseh engines. Alternative fuels with high alcohol

content can cause hard starting, poor engine performance,

and may cause internal engine damage.

ADD

NOTE

Damage and/or performance problems that will occur from

use of fuels, other than those listed in the Operator’s

Manuals will not be considered warranty.

Figure 7. Engine Oil Level

IV. Before Starting Your Engine

A. Checking Oil Level

To avoid engine damage, it is important to:

• Check oil level before each use and every 5

operating hours when engine is warm. Check oil

level more frequently during engine break-in.

• Keep oil level between “FULL” and “ADD” marks on

dipstick. See Figure 7.

• Insure oil fill cap/plug is tightened securely.

NOTES

Do not overfill oil filler. Doing so may result in oil carry-over

to the air cleaner and equipment malfunction or damage.

Do not allow oil level to fall below the “ADD” mark on

dipstick. Doing so may result in equipment malfunction or

damage.

1. Carburetor

2. Primer

Contact your Authorized Tecumseh Servicing Dealer for

Tecumseh Oil.

3. Muffler

4. Spark Plug Cap

5. Oil Fill Cap

B. Filling Oil Sump

I. Oil Fill Cap or Oil Fill Plug with Dipstick

6. Fuel Fill Cap

7. Engine Stop Switch

8. Starter Cord Handle

9. Speed Control

10.Air Cleaner

If your engine has an oil fill cap go to step 1. If your engine

has an oil fill plug see "II. Oil Fill Cap Without Dipstick (Oil

Fill Plug)" instructions on page 5.

1. Be sure engine is upright and level.

2. Unscrew oil fill cap from oil filler tube and wipe dipstick

clean. See Figure 8.

Figure 8. Engine with Oil Fill Dipstick

Page 4

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

NOTE

Some engine models feature an oil fill plug with an attached

dipstick. See Figure 9.

3. Screw oil fill cap or oil fill plug back into oil filler tube.

Tighten securely.

4. Unscrew and remove oil fill cap or oil fill plug from oil

filler tube. Note oil level. If oil reading on dipstick is

below “ADD” mark, slowly add oil to reach “FULL” level.

See Figure 7 on page 4.

5. Screw oil fill cap or oil fill plug back into oil filler tube.

Tighten securely.

1. Oil Fill Plug With Dipstick

2. Oil Fill Plug

6. Wipe away any spilled oil.

II. Oil Fill Cap Without Dipstick (Oil Fill Plug)

Figure 9. Other Possible Oil Fill Locations

If your engine has an oil fill plug go to step 1. If your engine

has an oil fill cap see "I. Oil Fill Cap or Oil Fill Plug with

Dipstick" instructions on page 4.

1. Be sure engine is upright and level.

2. Clean area around oil fill plug. See Figure 9.

3. Unscrew oil fill plug.

4. Add oil to overflow point, making sure to avoid spilling.

5. Screw oil fill plug back into oil fill hole. Tighten securely.

6. Wipe away any spilled oil.

C. Filling Fuel Tank

Figure 10. Fuel Cap Insert Symbol

Front View

An adult should fuel this engine.

WARNING

NEVER allow children to refuel this

engine. Gasoline (fuel) vapors are highly flammable and

can explode. Fuel vapors can spread and be ignited by a

spark or flame many feet away from engine. To prevent

injury or death from fuel fires, follow these instructions:

1. Stop engine and allow it to cool before refueling.

2. Be sure engine is outdoors and in a well-ventilated

area.

Bottom View

3. Clean area around fuel fill cap and remove fuel fill cap.

See Figure 8 on page 4.

4. Using an approved red GASOLINE container, add fuel

slowly, being careful to avoid spilling. DO NOT overfill

fuel tank. Leave space in the tank to allow fuel to

expand without overflowing.

Figure 11. Possible Anti-Splash Fuel Fill Cap(s)

Fuel

Tank

5. Replace anti-splash fuel fill cap securely and wipe up

spilled fuel before starting engine. If fuel is spilled DO

NOT start engine. Move machine away from area of

spillage. Avoid creating any source of ignition until fuel

vapors are gone.

Fuel Valve

“Open”

NOTES

Remove and discard white plastic fuel tank insert, if

provided. See Figure 10.

Position

Shown

Turn Valve Clockwise

To “Off” Position

Replace a damaged or missing gas cap only with a genuine

Tecumseh replacement anti-splash fuel fill cap. Failure to do

so may VOID YOUR WARRANTY. See Figure 11.

Figure 12. Fuel Valve Positions

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 5

D. Engine Stop Switch

Some engines are equipped with an optional Stop Switch.

This rocker switch is used to shut off the ignition that

supplies the spark plug with power. Pressing the "OFF"

position will turn the engine off when it is running. This

switch must be in the “ON” position or the engine will not

start. See Figure 14.

STOP

STOP SLOW

RUN FAST CHOKE PRIMER

Figure 13. Typical Engine Symbols

E. Optional Fuel Valve

Some engines are equipped with an optional fuel valve.

See Figure 12

V. Starting Your Engine

An adult should start the engine. Only

WARNING

allow children to start engine if an

adult has determined they are

experienced and capable of such operation.

If you are unable to start this engine

WARNING

after following instructions in this

manual, contact your Authorized

Tecumseh Servicing Dealer. To avoid serious burn injuries

or damage to your engine, DO NOT attempt to start or

troubleshoot this engine in any other way. For example:

• DO NOT use starting fluid.

• DO NOT spray flammable vapors into carburetor or

onto air cleaner.

• DO NOT put flammable liquids into carburetor or

onto air cleaner.

1. Carburetor

2. Primer

• DO NOT operate engine or pull on starter rope with

spark plug removed. Fuel can spray from spark plug

hole and ignite.

3. Muffler

4. Spark Plug Cap

5. Oil Fill Cap

This section contains starting instructions for several

different types of engines. In order to locate the instructions

that apply to your engine, first determine what type of starter

you have. If you have an electric starter see "A. Engines

with Electric Starters" instructions below. If you have a

manual recoil starter, see "B. Engines with Recoil Starters"

instructions on page 8.

6. Fuel Fill Cap

7. Engine Stop Switch

8. Starter Cord Handle

9. Speed Control

10.Air Cleaner

A. Engines with Electric Starters

Figure 14. Engine Components

Only one of the following two sections will apply to your

engine. See Table 3.

Table 3. Engine Sections with Electric Starters

If your engine has:

Go to:

Primer Bulb Only

Section A.I

Section A.II

Choke Only

I. Engine With Primer Bulb

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

2. Move Equipment Control (see equipment manufacturer’s

instructions) or Engine Throttle Control to “FAST”

position. See Figures 13 and 14.

Page 6

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

3. When starting a cold engine, push primer bulb firmly

with your thumb 3 times, allowing primer bulb to return

completely to original position between pushes. See

Figure 15.

NOTES

Cooler temperatures may require pushing primer bulb firmly

with your thumb 5 times.

DO NOT use primer to restart a warm engine after a short

shutdown. Doing so will flood the engine and may result in

equipment malfunction.

Figure 15. Engine Primer Bulb

DO NOT operate an electric starter for more than 5 seconds

each attempt.

4. Push starter button or turn ignition switch key to start

engine.

5. When engine starts, release starter button or ignition

switch key.

6. If engine fails to start after 3 attempts repeat steps 2

thru 5 and try again.

7. If engine does not start after following steps 1 thru 6,

contact your Authorized Tecumseh Servicing Dealer.

DO NOT attempt to start or troubleshoot this engine in

any other way.

1. Full Choke Position

2. 1/2 Choke Position

3. No Choke Position

II. Engine With Choke

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

Figure 16. Engine Choke Positions

2. Move Choke Control to “FULL CHOKE” position. See

Figure 16.

NOTES

If engine starts but falters when Choke Lever is moved to

“NO CHOKE” position:

NOTE

If restarting warm engine after a short shutdown, move

Choke Control to “NO CHOKE” position. See Figure 16.

a. Momentarily move Choke Lever back to “FULL

CHOKE” position.

3. Move Equipment Control (see equipment manufacturer’s

instructions) or Engine Throttle Control to “FAST”

position.

b. Next, move Choke Lever to “1/2 CHOKE” position.

c. Finally, move Choke Lever to “NO CHOKE” position.

NOTE

DO NOT operate an electric starter for more than 5 seconds

each attempt.

If engine dies after Choke Lever is moved to “NO CHOKE”

position, repeat steps 2 thru 5 to restart engine.

6. If engine fires, but does not continue to run, move

Choke Lever to “NO CHOKE” position and start engine.

4. Push starter button or turn ignition switch key to start

engine.

7. If engine fails after 3 attempts in the “NO CHOKE”

position, repeat steps 2 thru 6 to restart engine.

5. When engine starts:

a. Release starter button or ignition switch key.

8. If engine does not start after following steps 1 thru 7,

contact your Authorized Tecumseh Servicing Dealer.

DO NOT attempt to start or troubleshoot this engine in

any other way.

b. Momentarily move Choke Lever to “1/2 CHOKE”

position until engine runs smoothly.

c. Next, move Choke Lever to “NO CHOKE” position.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 7

When pulling starter rope, the rope

can unexpectedly jerk back toward

B. Engines with Recoil Starters

WARNING

If you have an electric starter see "A. Engines with Electric

Starters" instructions on page 6. Only one of the following

two sections will apply to your engine. If you have a manual

recoil starter see Table 4.

engine causing serious injury. To avoid this risk, carefully

follow these instructions:

4. Grasp starter cord handle. See Figure 19.

a. Pull rope out slowly until you feel drag.

b. Next, pull rope with one rapid full arm stroke.

c. Return rope slowly to original position.

Table 4. Engine Sections with Recoil Starters

If your engine has:

Go to:

NOTE

Following the instructions listed in the steps above avoids

potential damage to the recoil mechanism.

Primer Bulb Only

Section B.I

Section B.II

Choke Only

5. If engine fails to start after 3 attempts, repeat steps 2

thru 4 and try again.

I. Engine With Primer Bulb

6. If engine does not start after following steps 1 thru 5,

contact your Authorized Tecumseh Servicing Dealer.

DO NOT attempt to start or troubleshoot this engine in

any other way.

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

2. Move Equipment Control (see equipment manufacturer’s

instructions) or Engine Throttle Control to “FAST”

position, if present. See Figure 17.

3. When starting a cold engine, push primer bulb firmly

with your thumb 3 times, allowing primer bulb to return

completely to original position between pushes. See

Figure 18.

NOTE

Cooler temperatures may require pushing primer bulb firmly

with your thumb 5 times.

DO NOT use primer to restart a warm engine after a short

shutdown. Doing so will flood the engine and may result in

equipment malfunction.

Page 8

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

II. Engine With Choke

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

STOP

2. Move Engine Choke Lever to “FULL CHOKE” position.

See Figure 20.

STOP SLOW

RUN FAST CHOKE PRIMER

Figure 17. Typical Engine Symbols

NOTE

If restarting a warm engine after a short shutdown, move

Choke Lever to “NO CHOKE” position. See Figure 20.

3. Move Equipment Control (see manufacturer’s

instructions) or Engine Throttle Control to “FAST”

position. See Figure 17.

When pulling starter rope, the rope

WARNING

can unexpectedly jerk back toward

engine causing serious injury. To avoid this risk, carefully

follow these instructions:

4. Grasp starter cord handle. See Figure 19.

a. Pull rope out slowly until you feel drag.

b. Next, pull rope with one rapid full arm stroke.

c. Return rope slowly to original position.

Figure 18. Engine Primer Bulb

NOTE

Following the instructions listed in the steps above avoids

potential damage to the recoil mechanism.

5. When engine starts:

a. Momentarily move Choke Lever to “1/2 CHOKE”

position until engine runs smoothly.

b. Next, move Choke Lever to “NO CHOKE” position.

NOTES

If engine starts but falters when Choke Lever is moved to

“NO CHOKE” position:

Figure 19. Starter Cord Handle

a. Momentarily move Choke Lever back to “FULL

CHOKE” position.

b. Next, move Choke Lever to “1/2 CHOKE” position.

c. Finally, move Choke Lever to “NO CHOKE” position.

If engine dies after Choke Lever is moved to “NO CHOKE”

position, repeat steps 2 thru 5 to restart engine.

6. If engine fires, but does not continue to run, move

choke lever to “NO CHOKE” position and start engine.

7. If engine fails after 3 attempts in the “NO CHOKE”

position, repeat steps 2 thru 6 to restart engine.

8. If engine does not start after following steps 1 thru 7,

contact your Authorized Tecumseh Servicing Dealer.

DO NOT attempt to start or troubleshoot this engine in

any other way.

1. Full Choke Position

2. 1/2 Choke Position

3. No Choke Position

Figure 20. Engine Choke Positions

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 9

VI. Stopping Your Engine and

Short-Term Storage

Stop engine according to equipment manufacturer’s

instructions.

To avoid unsupervised operation of

WARNING

an engine, especially by children,

NEVER leave it unattended when it is running. Always turn

off the engine after use and remove ignition key, if

provided.

NEVER store the engine with fuel in

WARNING

the fuel tank inside a building with

Figure 21. Possible Oil Drain Plug Locations

potential sources of ignition such as hot water and space

heaters, clothes dryers, electric motors, etc.

VII. Maintenance

An adult should perform maintenance

WARNING

on this engine. Only allow children to

perform maintenance if an adult has determined they are

experienced and capable of such operation.

To prevent accidental starting when working on equipment,

always:

• Disconnect spark plug wire and keep it away from

spark plug. See "G. Avoid Accidental Starts"

instructions on page 2.

• Keep the disconnected spark plug wire

securely away from metal parts where arcing

could occur.

• Attach the spark plug wire to the grounding

post, if provided.

• Disconnect battery at negative terminal first, if

engine is equipped with an electric starter.

Figure 22. Possible Oil Fill Locations

3. Be sure the gas cap is on and is tightened securely.

4. Clean area around oil drain plug. See Figure 21.

• Turn off all engine switches.

• Remove ignition key, if provided.

5. Place approved recyclable oil container

under oil drain plug, tipping engine to

position the oil drain plug at the lowest

point on the engine. (See equipment

manufacturer’s instructions).

A. Checking and Changing Oil

To avoid engine damage, it is important to:

• Check oil level before each use and after every

5 operating hours when engine is warm.

See "A. Checking Oil Level" instructions on page 4.

6. Remove oil drain plug and drain oil into approved con-

tainer. See Figure 21.

• Change oil after first 2 operating hours and every 25

operating hours thereafter; more often if operated in

extremely dusty or dirty conditions. Engine should

still be warm but not hot from recent use.

NOTE

Used oil must be disposed of at a proper collection center.

1. Be sure you find the correct drain plug location, if

provided. See Figure 21.

7. Install oil drain plug and tighten securely.

8. Fill with recommended oil. See "III. Oil and Fuel Speci-

fications" instructions on page 3. See Table 1, on page

3. See Figure 22.

2. Disconnect spark plug wire and keep it away from

spark plug. See "G. Avoid Accidental Starts" instruc-

tions on page 2.

9. Wipe away any spilled oil.

• Keep the disconnected spark plug wire securely

away from metal parts where arcing could occur.

10. Carefully disconnect spark plug wire from grounding

post, if provided.

• Attach the spark plug wire to the grounding post, if

provided.

11. Carefully re-connect spark plug wire to spark plug.

Page 10

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

B. Removing Debris from Engine

Before each use, remove grass clippings, dirt and debris

from the following areas:

• Levers and Linkage

• Cooling Fins

• Air Intake Screen

• Guards

Removing debris will facilitate adequate cooling, correct

engine speed and reduce the risk of fire. See Figure 23.

1. Levers and Linkage

2. Cooling Fins

C. Spark Plug

Check spark plug yearly or every 100 operating hours.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Air Intake Screen

Figure 23. Debris Removal Areas

3. Replace spark plug if porcelain is cracked or if elec-

trodes are:

• Pitted

• Burned

• Fouled with deposits

4. Check electrode gap with wire feeler gauge and set

gap to .030 in. (0.76 mm) if necessary. See Figure 24.

5. Install spark plug and tighten securely.

NOTE

A resistor spark plug must be used for replacement. Contact

your Authorized Tecumseh Servicing Dealer for a Tecumseh

Resistor Spark Plug.

1. .030 in. (0.76 mm) Gap

2. Electrodes

3. Porcelain

D. Cleaning/Replacing Air Cleaner

Figure 24. Resistor Spark Plug

Your engine has an air cleaner which helps prevent

premature engine wear and failure. NEVER run engine

without complete air cleaner installed on engine. Your air

cleaner periodically needs to be cleaned or replaced.

NOTE

Contact your Authorized Tecumseh Servicing Dealer for a

Tecumseh Air Cleaner.

I. Servicing Foam Pre-Filters

Inspect and clean or replace foam pre-filters every 3 months

or every 25 operating hours. Clean daily if used in extremely

dusty conditions. After removing the filter, follow these

cleaning instructions below:

1. Wash in warm water and detergent solution then press

(DO NOT twist) until all dirt is removed.

2. Rinse thoroughly until water is clear.

3. Wrap in a clean cloth and press (DO NOT twist) until

completely dry.

NOTE

DO NOT oil foam pre-filter.

4. Replace foam pre-filter onto paper filter.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 11

II. Servicing Paper Filters

Paper filters cannot be cleaned and must be replaced once

a year or every 100 operating hours; more often if used in

extremely dusty conditions. Replacement filters are

available at a Authorized Tecumseh Servicing Dealer.

NOTE

DO NOT put oil on or clean a paper filter.

III. Removal and Installation of Air Filters

1. Remove wing nut and cover. See Figure 25.

2. Remove optional foam pre-filter, if present from cover.

3. Remove paper element from base.

4. Clean inside of base and cover thoroughly.

5. Install paper element into base.

6. Install foam pre-filter, if present into cover.

7. Install cover on base.

8. Install wing nut and tighten securely.

E. Anti-Icing Baffle

Some engines may be equipped with an anti-icing air

cleaner baffle that prevents ice from forming in the

carburetor when the engine is run at temperatures below

32°F (0°C).

COLD WEATHER

BAFFLE

POSITION

“

ABOVE 32°F (0°C)

”FOR SUMMER

Engines equipped with the baffle will have an opening

which draws warm air from the muffler into the air cleaner

housing. To work effectively, it is necessary for the baffle to

block cold air from entering the air cleaner.

POSITION “

BELOW 32°F (0°C)

”

FOR WINTER

At temperatures of 32°F (0°C) and Below

1. Remove wing nut from air cleaner cover. See Figure 25.

2. Remove air cleaner cover from base.

1. Red Baffle

2. Baffle Summer Position

3. Baffle Winter Position

4. Base

3. Remove red baffle from inside of air cleaner cover.

4. Insert red baffle in “WINTER” position shown.

5. Install air cleaner cover onto base.

5. Paper Element

6. Foam Pre-Filter (Optional)

7. Cover

6. Install wing nut and tighten securely.

At temperatures above 32°F (0°C)

8. Wing Nut

1. Remove wing nut from air cleaner cover. See Figure 25.

2. Remove air cleaner cover from base.

Figure 25. Air Cleaner and Optional Anti-Icing Baffle

3. Remove red baffle from inside of air cleaner cover.

4. Insert red baffle in “SUMMER” position shown.

5. Install air cleaner cover onto base.

6. Install wing nut and tighten securely.

Page 12

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

F. Alternator (Optional)

VIII. Transporting Your Engine

NEVER transport this engine inside

another vehicle or in any enclosed

For alternator related electrical problems such as:

• Inoperative starter

WARNING

space if there is any gasoline in the tank. Fuel vapor or

spilled fuel may ignite.

• Discharged battery

• Fuse replacement

If there is fuel in the fuel tank, close

WARNING

the fuel shut off valve, if equipped,

• Alternator maintenance/repairs

and transport the engine upright in an open vehicle, such

as an open trailer or open bed of a pickup truck.

See your equipment manufacturer’s instructions and an

Authorized Tecumseh Servicing Dealer.

If you do not have an open vehicle and have to transport

the engine upright in a closed vehicle, follow these steps

for emptying the fuel tank before transporting:

G. Carburetor

If you think your carburetor needs adjusting, see your

nearest Authorized Tecumseh Servicing Dealer. Engine

performance should not be affected at altitudes up to 7,000

feet (2,134 meters). For operation at higher elevations,

contact your Authorized Tecumseh Servicing Dealer.

1. Empty fuel tank by using a commercially available

suction device designed for use with gasoline.

To avoid severe injury or death,

WARNING

do not pour fuel from engine or

siphon fuel by mouth.

H. Engine Speed

2. Drain fuel into an approved red GASOLINE container,

being careful to avoid spilling.

To avoid serious injury or death, DO

WARNING

NOT modify engine in any way.

Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. NEVER

tamper with factory setting of engine governor.

3. Run the engine until remaining fuel is consumed.

NEVER leave the engine unattended

WARNING

when it is running and NEVER run

engine in enclosed areas.

Running the engine faster than the speed set at the factory

can be dangerous and will VOID THE ENGINE

WARRANTY.

I. Adjustments

Do not make any engine adjustments. Factory settings are

satisfactory for most conditions. If adjustments are needed,

contact your Authorized Tecumseh Servicing Dealer.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 13

III. Fuel System

IX. Storing Your Engine

A. Short Term/Seasonal Storage

I. Clean Engine

To avoid stale gas and carburetor problems, treat the fuel

system in the following method below:

NOTES

Tecumseh recommends using ULTRA-FRESH™ or Fuel

Saver Plus Gasoline Stabilizer plus Fuel System Cleaner as

an acceptable method of minimizing formation of fuel gum

deposits during storage. This product is available from your

Authorized Tecumseh Servicing Dealer.

Before servicing the engine remove the blower housing. In

addition, remove grass clippings, dirt and debris from the

following areas:

• Cooling fins

• Air intake screen

• Levers

Always follow mix ratio found on stabilizer container. Failure

to do so may result in equipment damage.

• Linkage

It is not necessary to drain stabilized gas from carburetor.

• Guards

IV. Fuel Treatment

• Carburetor

• Head

1. Add fuel stabilizer according to manufacturer’s

instructions.

Removing debris will facilitate adequate cooling, correct

engine speed and reduce the risk of fire.

2. Run engine at least 10 minutes after adding stabilizer

to allow it to reach carburetor.

NEVER store the engine with fuel in

WARNING

the fuel tank inside a building with

II. Fuel Storage

NEVER store engine with fuel in fuel

WARNING

potential sources of ignition such as hot water and space

heaters, clothes dryers, electric motors, etc.

tank inside a building with potential

sources of ignition such as hot water and space heaters,

clothes dryers, electric motors, etc. Failure to do so may

result in an explosion and result in death or serious injury.

NOTE

Instead of using a fuel preservative/stabilizer, you can

empty the fuel tank as described. See "I. Draining Fuel"

instructions.

NOTES

If engine fuel stored in the gas tank and/or an approved gas

container is to be unused without gasoline stabilizer for

more than 15-30 days, prepare it for short term/seasonal

storage. See "IV. Fuel Treatment" instructions.

B. Extended Storage

I. Draining Fuel

If engine fuel is to be stored for more than one season,

without gasoline stabilizer, it will gradually deteriorate. Also,

if it is stored in the engine’s gas tank without gasoline

stabilizer it is likely that your carburetor will have gum

deposits, a clogged fuel system and will void your warranty.

Prepare the fuel for extended storage. See "B. Extended

Storage" instructions.

NOTES

Clean debris from engine before draining fuel from

carburetor. See "I. Clean Engine" instructions.

If you have prepared your fuel for short term storage it is not

necessary to drain fuel that contains stabilizer from your

carburetor. See "A. Short Term/Seasonal Storage"

instructions.

If you operate the engine during all 4 seasons, it is not

necessary to lubricate the cylinder bore.

To avoid severe injury or death,

WARNING

DO NOT pour fuel from engine or

siphon fuel by mouth.

1. To prevent serious injury from fuel fires, empty fuel tank

by running engine until it stops from lack of fuel. DO

NOT attempt to pour fuel from engine.

2. Run the engine while waiting until the remaining fuel is

consumed.

NEVER leave the engine unattended

when it is running and NEVER run

WARNING

engine in enclosed areas.

3. Begin servicing the cylinder bore. See "II. Oil Cylinder

Bore" instructions on page 15.

Page 14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

II. Oil Cylinder Bore

When lubricating cylinder bore, fuel

may spray from spark plug hole. To

WARNING

prevent serious injury from fuel fires, follow these

instructions:

1. Disconnect spark plug wire and keep it away from

spark plug. See "G. Avoid Accidental Starts" instruc-

tions on page 2. See Figures 26 and 27.

• Keep the disconnected spark plug wire

securely away from metal parts where arcing

could occur.

Figure 26. Disconnecting/Connecting Spark Plug

• Attach the spark plug wire to the grounding

post, if provided.

• Disconnect battery at negative terminal first, if

engine is equipped with an electric starter.

• Turn off all engine switches.

• Remove ignition key, if provided.

2. Remove spark plug.

3. Squirt 1oz. (30ml) of clean engine oil into spark plug

hole.

4. Cover spark plug hole with rag to prevent fuel from

spraying from spark plug hole when starter rope is

pulled.

Figure 27. Typical Spark Plug Connection

NOTES

For engines equipped with recoil starters proceed to Step 5.

III. Oil

Change oil if not changed within the last 3 months. See "A.

Checking and Changing Oil" instructions on page 10.

For engines equipped with electric starters proceed to Step

5. Grasp starter cord handle and pull out slowly using a

full arm stroke. Repeat once. (This will distribute oil

throughout the cylinder to prevent corrosion during

storage.)

IV. Battery

See equipment manufacturer’s instructions for proper

battery storage if machine is equipped with a battery.

6. Install spark plug.

7. Carefully disconnect spark plug wire from grounding

post, if provided.

NOTE

Connect spark plug wire before attempting to start engine.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 15

X. Preventing Forest, Brush and

Grass Fires

XI. Maintenance Intervals

Maintenance is one of the most important things that you

can do to extend the life of your Tecumseh Engine. If you

are unable to perform maintenance intervals yourself,

contact your nearest Authorized Tecumseh Servicing

Dealer. You may also call Tecumseh Power Company at

1-800-558-5402 or visit www.TecumsehPower.com to

locate your dealer.

Local, state and federal laws may require use of a spark

arrester to prevent fires. For example, it is a violation of

California Public Resources Code (section 4442) to use or

operate engine on any forest-covered, brush-covered or

unimproved grass-covered land unless engine is equipped

with a spark arrester. Spark arrester must be maintained in

effective working order by owner and/or operator.

ALWAYS promptly follow maintenance intervals listed on

the next two pages. See Table 5.

To determine if your engine has a spark arrester, locate the

muffler on your engine. For example, the muffler discharge

will have a spark arrester cover that reads “Tecumseh

Screen Type 36085”.

Table 5. Maintenance Intervals

If your engine does not have a spark arrester, you may

purchase one from your Authorized Tecumseh Servicing

Dealer. In some cases the muffler may need to be replaced

to allow the spark arrester to be installed.

Procedure

Time

After first 2 hrs.

when engine is warm

Change

Oil

Check

Oil Level

5 hrs. or Before Each Use

25 hrs. or 3 mos.

Clean

Cooling Fins

Change

Oil

Clean

Foam Pre-Filter

25 hrs. or 3 mos.

100 hrs. or

seasonally

Replace

Paper Element

100 hrs. or

seasonally

Check

Spark Plug

200 hrs. or

seasonally

Replace

Spark Plug

First Scheduled Maintenance

After First 2 Hours When Engine is Warm

1. Change Oil

Date_______________Owner/Dealer

Page 16

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

Before Each Use Scheduled Maintenance

Every 25 Hours or 3 Months Scheduled Maintenance

1. Change Oil

2. Clean Foam Pre-Filter

Every 5 Hours or Before Each Use

1. Check Oil Level

2. Clean Cooling Fins

Date_______________Owner/Dealer

Every 100 Hours or Seasonally

1. Replace Paper Element

2. Check Spark Plug

Date_______________Owner/Dealer

Every 200 Hours or Seasonally

1. Replace Spark Plug

Date_______________Owner/Dealer

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 17

Page 18

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

NOTES

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 19

CALIFORNIA & US EPA EMISSION CONTROL WARRANTY STATEMENT

The U. S. Environmental Protection Agency (“EPA”), the

California Air Resources Board (“CARB”) and Tecumseh Power

Company are pleased to explain the Federal and California

Emission Control Systems Warranty on your new small off-road

engine. In California, new 1995 and later small off-road engines

must be designed, built and equipped to meet the State’s

stringent anti-smog standards. In other states, new 1997 and later

model year engines must be designed, built and equipped, at the

time of sale, to meet the U.S. EPA regulations for small non-road

engines. Tecumseh Power Company will warrant the emission

control system on your small off-road engine for the periods of

time listed below, provided there has been no abuse, neglect,

unapproved modification, or improper maintenance of your small

off-road engine.

You are responsible for presenting your small off-road engine to a

Tecumseh Authorized Service Outlet (any Tecumseh Registered

Service Dealer, Tecumseh Authorized Service Distributor or

Tecumseh Central Warehouse Distributor) as soon as a problem

exists. The warranty repairs should be completed in a reasonable

amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either an

Authorized Tecumseh Servicing Dealer and/or Tecumseh Power

Company, c/o Service Manager, 900 North Street, Grafton, WI

53024-1499. Telephone 1-262-377-2700 [or in USA/Canada call

1-800-558-5402].

IMPORTANT NOTE

This warranty statement explains your rights and obligations

under the Emission Control System Warranty (“ECS Warranty”)

which is provided to you by Tecumseh Power Company pursuant

to California law. Tecumseh Power Company also provides to

original purchasers of new Tecumseh Power Company engines

the Tecumseh Power Company Limited Warranties for New

Tecumseh Engines and Electronic Ignition Modules. The

Tecumseh Power Company Limited Warranties for New

Tecumseh Engines and Electronic Ignition Modules (“Tecumseh

Power Company Warranty”) are located on the back cover of the

Operator’s Manual, enclosed with all new Tecumseh Power

Company engines. The ECS Warranty applies only to the

emission control system of your new engine. To the extent that

there is any conflict in terms between the ECS Warranty and the

Tecumseh Power Company Warranty, the ECS Warranty shall

apply except in any circumstances in which the Tecumseh Power

Company Warranty may provide a longer warranty period. Both

the ECS Warranty and the Tecumseh Power Company Warranty

describe important rights and obligations with respect to your new

engine.

Your emission control system may include parts such as the

carburetor, air cleaner assembly, ignition system, exhaust

system, crankcase breather assembly and, the evaporative

control system. Also included may be the compression release

system and other emission-related assemblies.

Where

warrantable condition exists, Tecumseh Power

Company will repair your small off-road engine at no cost to you

for diagnosis, parts and labor.

MANUFACTURER’S EMISSION CONTROL

SYSTEM WARRANTY COVERAGE

Emission control systems on 1995 and later model year California

small off-road engines are warranted for two years as hereinafter

noted. In other states, 1997 and later model year engines are also

warranted for two years. If, during such warranty period, any

emission-related part on your engine is defective in materials or

workmanship, the part will be repaired or replaced by Tecumseh

Power Company

Warranty service can only be performed by a Tecumseh Power

Company Authorized Servicing Dealer. At the time of requesting

warranty service, evidence must be presented of the date of sale

to the original purchaser. The purchaser shall pay any charges for

making service calls and/or for transporting the products to and

from the place where the inspection and/or warranty work is

performed. The purchaser shall be responsible for any damage or

loss incurred in connection with the transportation of any engine

or any part(s) thereof submitted for inspection and/or warranty

work.

OWNER’S WARRANTY RESPONSIBILITIES

As the small off-road engine owner, you are responsible for the

performance of the required maintenance listed in your

Operator’s Manual, but Tecumseh Power Company will not deny

warranty solely due to the lack of receipts or for your failure to

provide written evidence of the performance of all scheduled

maintenance.

As the small off-road engine owner, you should, however, be

aware that Tecumseh Power Company may deny you warranty

coverage if your small off-road engine or a part thereof has failed

due to abuse, neglect, improper maintenance or unapproved

modifications.

If you have any questions regarding your warranty rights and

responsibilities, you should contact Tecumseh Power Company

at 1-262-377-2700 or in USA/Canada call 1-800-558-5402.

Revised July, 2005

IMPORTANT!

The emission Regulations may be different for your country. The emissions Control Warranty Statement is only applicable

to engines with an emissions compliance statement and decal that references “Emissions Regulations”.

Page 20

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-1032-14

EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (“ECS Warranty”) for 1995

and later model year California small off-road engines (for other

states, 1997 and later model year engines):

5. The owner shall not be charged for diagnostic labor which

leads to the determination that a part covered by the ECS

Warranty is in fact defective, provided that such diagnostic

work is performed at a Tecumseh Authorized Service

Outlet.

A. APPLICABILITY: This warranty shall apply to 1995 and later

model year California small off-road engines (for other states,

1997 and later model year engines). The ECS Warranty

Period shall begin on the date the new engine or equipment is

delivered to its original, end-use purchaser, and shall continue

for 24 consecutive months thereafter.

6. Tecumseh Power Company shall be liable for damages to

other original engine components or approved

modifications proximately caused by a failure under

warranty of an emission-related part covered by the ECS

Warranty.

B. GENERAL EMISSIONS WARRANTY COVERAGE:

Tecumseh Power Company warrants to the original, end-use

purchaser of the new engine or equipment and to each

subsequent purchaser that each of its small off-road engines

is:

7. Throughout the ECS Warranty Period, Tecumseh Power

Company shall maintain a supply of warranted emission-

related parts sufficient to meet the expected demand for

such emission-related parts.

1. Designed, built and equipped so as to conform with all

applicable regulations adopted by the Air Resources

Board pursuant to its authority in Chapters 1 and 2, Part 5,

Division 26 of the Health and Safety Code, and

8. Any Tecumseh Power Company authorized and approved

emission-related replacement part may be used in the

performance of any ECS Warranty maintenance or repair

and will be provided without charge to the owner. Such

use shall not reduce Tecumseh Power Company ECS

Warranty obligations.

2. Free from defects in materials and workmanship which, at

any time during the ECS Warranty Period, will cause a

warranted emissions-related part to fail to be identical in all

material respects to the part as described in the engine

manufacturer’s application for certification.

9. Unapproved add-on or modified parts may not be used to

modify or repair a Tecumseh Power Company engine.

Such use voids this ECS Warranty and shall be sufficient

grounds for disallowing an ECS Warranty claim.

Tecumseh Power Company shall not be liable hereunder

for failures of any warranted parts of a Tecumseh Power

Company engine caused by the use of such an

unapproved add-on or modified part.

C. THE ECS WARRANTY ONLY PERTAINS TO EMISSION-

RELATED PARTS ON YOUR ENGINE AS FOLLOWS:

1. Any warranted, emissions-related parts which are not

scheduled for replacement as required maintenance in the

Operator’s Manual shall be warranted for the ECS

Warranty Period. If any such part fails during the ECS

Warranty Period, it shall be repaired or replaced by

Tecumseh Power Company according to Subsection 4

below. Any such part repaired or replaced under the ECS

Warranty shall be warranted for any remainder of the ECS

Warranty Period.

EMISSION-RELATED PARTS INCLUDE THE FOLLOWING:

1. Carburetor Assembly including internal components:

a) Carburetor gaskets

b) Intake pipe

2. Air Cleaner Assembly including components:

a) Air filter element

2. Any warranted, emissions-related part which is scheduled

only for regular inspection as specified in the Operator’s

Manual shall be warranted for the ECS Warranty Period. A

statement in such written instructions to the effect of

“repair or replace as necessary”, shall not reduce the ECS

Warranty Period. Any such part repaired or replaced under

the ECS Warranty shall be warranted for the remainder of

the ECS Warranty Period.

3. Ignition System including components:

a) Spark plug

b) Ignition module

c) Flywheel assembly

4. Exhaust System including components:

3. Any warranted, emissions-related part which is scheduled

for replacement as required maintenance in the Operator’s

Manual, shall be warranted for the period of time prior to

the first scheduled replacement point for that part. If the

part fails prior to the first scheduled replacement, the part

shall be repaired or replaced by Tecumseh Power

Company according to Subsection 4 below. Any such

emissions-related part repaired or replaced under the ECS

Warranty, shall be warranted for the remainder of the ECS

Warranty Period prior to the first scheduled replacement

point for such emissions-related part.

a) Catalytic muffler (if so equipped)

b) Muffler gasket (if so equipped)

c) Exhaust manifold (if so equipped)

5. Crankcase Breather Assembly including components

a) Breather connection tube

6. Evaporative Control System including components:

a) Fuel line(s)

b) Fuel filter

4. Repair or replacement of any warranted, emissions-

related part under this ECS Warranty shall be performed

at no charge to the owner at a Tecumseh Authorized

Service Outlet.

c) Canister (if so equipped)

d) Fuel tank (if so equipped)

Revised July, 2005

e) Fuel fill cap (if so equipped)

IMPORTANT!

The emission Regulations may be different for your country. The emissions Control Warranty Statement is only applicable

to engines with an emissions compliance statement and decal that references “Emissions Regulations”.

181-1032-14

Four-Cycle Engine • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 21

XII. Warranty Information

LIMITED WARRANTY FOR NEW TECUMSEH ENGINES

AND ELECTRONIC IGNITION MODULES

For the time period shown below from the date of purchase and subject to the exceptions and limitations described herein, Tecumseh Power Company will, at its option as

the exclusive remedy, either repair or replace for the original purchaser, free of charge, any part of any new Tecumseh engine which is found, upon examination by any

Authorized Tecumseh Servicing Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. This Limited

Warranty DOES NOT COVER (i) any Tecumseh engine or part(s) thereof used to power any vehicle in competitive racing and/or used on any commercial or rental track, or

(ii) defects or damage caused by alterations or modifications of new Tecumseh engines or parts or by normal wear, accidents, improper maintenance, improper use or

abuse of the product, or failure to follow the instructions contained in an Instruction Manual for the operation of the new Tecumseh engine or part. The cost of normal

maintenance or replacement of service items which are not defective shall be paid for by the original purchaser. At the time warranty service is requested, evidence must

be presented of the date of purchase by the original purchaser. Any charge for making service calls and/or for transporting any engine or part(s) thereof to and from the

place where the inspection and/or warranty work is performed is payable solely by the purchaser. The purchaser is responsible for any damage or loss incurred in

connection with the transportation of any engine or part(s) thereof submitted for inspection and/or warranty work. WARRANTY SERVICE CAN ONLY BE PERFORMED

BY A TECUMSEH AUTHORIZED SERVICE OUTLET. Warranty service can be arranged by contacting a Tecumseh Authorized Service Outlet (any Tecumseh Registered

Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh c/o Service Manager, 900 North

Street, Grafton, Wisconsin 53024-1499.

(4)

(5)

“CONSUMER USE”

“COMMERCIAL USE”

Warranty