375 Marcus Boulevard • Hauppauge, NY 11788 • USA
631.273.0500 • Fax: 631.273.0771
e-mail: [email protected]
Extensive Product Information Available at:
Document No. 98-1123E1 • Revised February 2007 • ©1994-2007 Atlantic Ultraviolet Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY WARNINGS
•
•
All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.
The following conventions are used to indicate and classify precautions in this manual and on product safety
labeling. Failure to observe precautions could result in injury to people or damage to property.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
Danger indicates an IMMINENTLY hazardous situation, which, if not avoided,
WILL result in death or serious injury.
Warning indicates a POTENTIALLY hazardous situation, which, if not avoided,
COULD result in death or serious injury.
Caution indicates a POTENTIALLY hazardous situation, which, if not avoided,
MAY result in minor or moderate injury.
Caution used without the safety alert symbol indicates a potentially hazardous
situation, which, if not avoided, may result in property damage.
This symbol/pictorial is used to identify an ELECTRICAL SHOCK or
ELECTROCUTION hazard.
This symbol/pictorial is used to identify an ULTRAVIOLET LIGHT hazard.
•
Product safety labels should be periodically inspected and cleaned, as necessary, to maintain good legibility.
Always replace illegible safety labels. Contact factory to obtain replacement safety labels.
SAFETY INSTRUCTIONS
!
WARNING: To guard against injury, basic safety precautions should be observed, including the following:
1. Read and follow ALL safety instructions.
2. Do not use this water purifier for other than its intended purpose as described in this manual.
3. Do not alter design or construction.
4.
!
DANGER: To prevent the risk of severe or fatal electrical shock, special precautions must be
taken since water is present near electrical equipment. Always disconnect power before performing
any maintenance.
5.
!
WARNING: Avoid exposure to direct or strongly reflected germicidal ultraviolet rays.
Germicidal ultraviolet rays are harmful to the eyes and skin.
6. Intended for indoor use only. The water purifier should be protected from the elements and from
temperatures below freezing.
7. Do not operate water purifier if power cord or plug is damaged.
8. Electrical power supplied, to the water purifier, MUST match power requirements listed on the
water purifier.
9. Plug the water purifier into an approved ground fault circuit interrupt (GFCI) receptacle.
10.
!
CAUTION: Do not operate without proper electrical ground.
11. Do not exceed water purifier’s maximum rated flow capacity.
12. Do not exceed maximum operating pressure of 100 PSI.
13. Read and follow all notices and warnings on the water purifier.
14. SAVE THESE INSTRUCTIONS.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT APPLICATION
CONSTRUCTION
•
•
•
•
•
•
The water purifier is designed to mount horizontally.
A drain port on the chamber aids in draining of the purifier.
The water purifier chamber is passivated and electropolished type 316 Stainless Steel.
The ballast housing is a combination of Stainless Steel Type 304 and Aluminum Alloy.
Coated chambers are available for uses with special applications, consult Factory.
Easy-off end caps allow for quick and easy lamp change, without disconnecting from the water supply or draining
the purifier. No tools are required.
PRINCIPLE OF OPERATION
The MightyPure™ design has been carefully conceived to provide adequate germicidal dosage throughout the
disinfection chamber. The dosage, as it applies to ultraviolet disinfection, is a function of time and the intensity of
ultraviolet radiation to which the water is exposed. The exposure time, in seconds, is the total time it takes the water to
flow through the disinfection chamber exposing it to the germicidal lamp. Exposure time is related to the flow rate; the
higher the flow rate, the lower the exposure time or the lower the flow rate, the higher the exposure time. The
ultraviolet intensity is the amount of energy, per unit time, emitted by the germicidal lamp. The Dosage is the product
of ultraviolet intensity and the exposure time. The operation of the MightyPure™ is as follows:
1. Water enters the purifier and flows into the annular space between the quartz sleeve and the chamber wall.
2. Suspended microorganisms are exposed to the ultraviolet rays emitted by the germicidal lamp.
3. The translucent sight port, or optional ultraviolet monitor, provides visual indication of germicidal lamp operation.
4. Water leaving the purifier is instantly ready for use, no further contact time is required.
LIMITATION OF USE
The water purifier is intended for the use with visually clear water, not colored, cloudy or turbid.
See “Water Quality” section below.
The water purifier is NOT intended for the treatment of water that has an obvious contamination or intentional source,
such as raw sewage; nor is the unit intended to convert wastewater to microbiologically safe drinking water.
WATER QUALITY
Water quality plays a major role in the transmission of germicidal ultraviolet rays. It is recommended that the water
does not exceed the following maximum concentration levels:
Table 1 - Maximum Concentration Levels
Turbidity:
5 NTU
0.05mg/l
10 mg/l
6.5 - 9.5
None
Manganese:
Total Suspended Solids:
pH:
Color:
Hardness:
Iron:
6 GPG or 102.6 PPM
0.3 mg/l
Effectively treating water with higher concentration levels than listed above can be accomplished, but may require
added measures to improve water quality to treatable levels. If, for any reason, it is believed the ultraviolet transmission
is not satisfactory, contact the factory.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
LOCATION
1. The water purifier is intended for indoor use only. The water purifier should be protected from the elements and
from temperatures below freezing. The ambient temperature, in the area surrounding the water purifier, should be
between 33ꢀ F and 100ꢀ F.
2. Electrical power supplied to the water purifier MUST match power requirements listed on the water purifier. Use
of a voltage surge protector is recommended.
3. Plug water purifier into an approved ground fault circuit interrupt (GFCI) receptacle.
4. The water purifier should be located in a dry, well-lit area, which provides enough room to perform routine
maintenance. This includes a minimum distance of one chamber length from the chamber end, to allow for
cleaning and/or the changing of the lamp and quartz sleeve as well as a minimum of 6" on the opposite end of the
water purifier.
5. The water purifier should always be located closest to the point of use. This reduces the chance of the purified
water being re-contaminated by bacteria in the water distribution system after the water purifier.
6. CAUTION: As with any water handling device, the water purifier should be located in an area where any possible
condensation or leakage from the water purifier, any purifier accessory and/or plumbing will not result in damage
to the area surrounding the water purifier. For added protection, it is recommended that a suitable drain pan be
installed under the purifier. The drain pan must be plumbed to an adequate, free flowing, drain to prevent water
damage in the event of a leak. There are numerous leak detection/flood stop devices, available on the market today,
designed to stop the flow of water, reducing the chance of water damage due to leakage. For more details regard-
ing leak prevention and/or limiting damages due to leaks, please contact the factory.
7. The water purifier should be located after all other water devices, such as De-ionizers, Water Softeners, Carbon
Filters, Pre-Filters, Reverse Osmosis, Pressure Tanks, and Pumps. This reduces the chance of the purified water
being re-contaminated by bacteria in any of these units.
DIMENSIONAL DATA
Figure 1 - MightyPure™ Dimensional Drawing
Table 2 - MightyPure™ Dimensional Data
Model:
A
B
C
D
E
F
G
H
Inlet/Outlet
3
1
5
15
3
1
4
2
8
16
8
2
MP13A
6"
13"
5- / "
7"
13- / "
3- / "
4- / "
8- / "
/ "m NPT
3
3
1
5
15
3
3
4
4
2
8
16
8
4
MP16A
MP22A
MP36C
MP49C
8- / "
16"
22"
36"
49"
8- / "
10"
16- / "
3- / "
4- / "
8- / "
/ "m NPT
3
1
1
1
5
15
3
3
4
4
2
2
8
16
8
4
14- / "
13- / "
14- / "
22- / "
3- / "
4- / "
8- / "
/ "m NPT
1
1
15
11
1
2
2
16
16
2
28- / "
16"
26"
18"
36- / "
4- / "
5- / "
9- / "
1"m NPT
7
1
15
11
1
1
8
2
16
16
2
2
40- / "
30"
49- / "
4- / "
5- / "
9- / "
1- / "m NPT
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
1. Remove water purifier from shipping carton. Inspect water purifier, power cord and plug for damage. Do not operate if
there is any damage to the purifier, power cord or plug. Models MP13A through MP22A are shipped with the lamps
already installed, while the MP36C and MP49C lamps are packed separately. Keep the lamp aside for installation once
the purifier has been properly installed.
2. Units occasionally experience damage in shipment due to the fragility of the quartz sleeve. It is therefore recommended
to inspect the water purifier for damage to the quartz sleeve after it has been removed from the shipping carton. Each end
of the unit as well as the inlet and outlet should be viewed to see if the quartz sleeve has experienced damage. If the
quartz sleeve shows signs of damage it should be replaced before the purifier is pressurized. See “Quartz Sleeve
Cleaning or Replacement” in the “Maintenance” section for the proper method of replacing the quartz sleeve in your
water purifier.
Figure 2 - Recommended Installation
3. The water purifier should be mounted horizontally on a flat dry surface. Secure the water purifier using the mounting
holes in the ballast housing or with the optional wall mounting kit. The purifier should not be solely supported by its
plumbing connections.
4. The water purifier must be connected to the cold water line only.
5. It is recommended that a 5-micron sediment filter be installed, in line, prior to the water purifier. The sediment filter will
stop or trap any particulates from entering the water purifier. Particulates may cause damage to the quartz sleeve, as well
as interfere with the purifier’s ability to disinfect the water. The sediment filter may also help to reduce the amount of
routine cleaning of the quartz sleeve.
6. Shut off valves should be installed on both the inlet and outlet sides of the water purifier. The use of bypass valves is
not recommended. The shut off valves allow the purifier to be isolated from the water supply, which is required when
removing the quartz sleeve.
7. Unions should be installed on both the inlet and outlet of the water purifier; this will allow easy removal of the water
®
purifier from the plumbing, if required. Apply Teflon tape to threads of inlet and outlet ports to ensure a tight seal.
8. When all plumbing connections are complete, allow water to enter the water purifier at a low flow rate, until the purifier
is pressurized. With the purifier pressurized, it should be checked for leaks. Once it is determined that there are no leaks,
the inlet valve can be fully opened.
9. For Models with lamps packed separately, install lamp following the steps in “Lamp Installation or Replacement” section.
!
CAUTION: Lamp and quartz sleeve are easily damaged. Exercise care when installing lamp.
10.Once the plumbing hook ups are made, it is a good practice to disinfect the “downstream” plumbing between the purifier
and point of use. This is done by introducing chlorine into the purifier chamber, a 100-ppm solution of chlorine is
suggested. With the chlorine in the purifier chamber, turn the ultraviolet purifier on. Open the “downstream” outlet until a
chlorine odor is noticed. Close the outlet and allow the chlorine to remain in the plumbing for three (3) hours. Flush the
plumbing with ultraviolet purified water; allow the water to run for several minutes before use. This will allow the
chlorine to be flushed from the pipes.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOMMENDED OPTIONS
1 . Guardian™ Ultraviolet Monitor: Visually indicates the level of germicidal ultraviolet energy that penetrates the
quartz sleeve and the water within the water purifier. The ultraviolet monitor is capable of operating an optional
audio alarm and/or solenoid valve. The ultraviolet monitor will detect reduction of ultraviolet levels due to:
•
•
Fouling or deposits on the quartz sleeve.
Poor ultraviolet transmission through the water; color, turbidity, and organic or other impurities in the water
can reduce or interfere with the transmission of ultraviolet rays.
•
•
Lamp outage, component or power failure.
Depreciation of the lamp output due to usage or other cause. Lamp output gradually depreciates with use.
Lamp replacement is recommended once each year.
•
Use of the Guardian™ Ultraviolet Monitor is recommended by the U. S. Public Health Service “Criteria for
the Acceptability of an Ultraviolet Disinfection Unit.”
2. Sentry™ Safety Sensor: Pilot lamps provide constant visual monitoring of normal operation. In the event of
power or lamp failure the safety sensor indicates an alarm condition. The safety sensor is capable of operating an
optional audio alarm and/or solenoid valve.
3. Steralert™: Lamp Status Alarm produces a high pitched, pulsed tone when the water purifier is no longer
functioning due to lamp or power failure.
4. Flow Control Valve: Limits water flow to the rated capacity of the purifier. The flow control valve is located in
line prior to the water purifier, and should be protected from ultraviolet exposure by the use of a 90-degree elbow
fitting between the flow control valve and the water purifier.
5. Audio Alarm: Activated by the Ultraviolet Monitor or Safety Sensor, alerts the user to any malfunction detected.
6. Solenoid Valve: Operated in conjunction with the Ultraviolet Monitor, Safety Sensor or Time Delay Mechanism,
this valve prevents water flow through the water purifier when an abnormal condition is detected or in the event of
power failure.
7. Elapsed Time Indicator: A non-resettable display of the water purifier operating hours. Useful for scheduling and
recording maintenance and lamp replacement.
8. Time Delay Mechanism: Provides a 2-minute warm up period during which the ultraviolet lamp achieves its full
germicidal output before the water is allowed to flow through the water purifier. The time delay mechanism is used
in conjunction with, and is electrically connected to the Solenoid Valve.
9. Wall Mount Kit: Stainless steel wall brackets provide quick and easy installation and professional finish.
Pre-drilled and ready to install. Optimizes free air circulation to cool ballast housing.
10. Quantum Thermal Optimizer: Thermal relief valve used to help regulate the water temperature inside the water
purifier's disinfection chamber. Since the relative ultraviolet output, of a germicidal lamp, is affected by
temperature it is important to keep the lamp's temperature within the peak output temperature range.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
The water purifier is designed to operate with a minimal amount of maintenance, providing the water quality does not
exceed maximum concentration levels, see “Water Quality” in the “Product Application” section. Ordinary mainte-
nance consists of;
• Lamp replacement is recommended every 10,000 hours of operation, approximately 12 months of continuous service.
• Cleaning of the quartz sleeve, when conditions warrant.
• Always disconnect the water supply and completely drain the water purifier if it will be subjected to
temperatures below freezing, for extended periods of time.
INSPECTION
1. Regularly inspect the water purifier to ensure that the germicidal lamp is still in operation.
• On purifiers not equipped with the Ultraviolet Monitor, lamp operation can be verified by a visible glow
through the translucent sight port. This provides an indication of lamp operation and does not indicate the level
of ultraviolet intensity or transmission through the water.
• On purifiers so equipped, the Guardian™ Ultraviolet Monitor provides visual indication of the ultraviolet
intensity through the quartz sleeve and water in the purifier chamber.
2. To ensure proper operation of the water purifier, regular biological testing should be performed on a schedule
recommended by local public health authorities, or at minimum; at installation, quarterly for the first year of
service and annually, at lamp replacement, for the life of the water purifier.
LAMP-OUT PROTECTION
On MightyPure™ MODELS MP16A, MP22A & MP36C If power is applied to the purifier without a lamp con-
nected to the circuit or if the lamp fails, the purifier ballast's lamp-out protection will prevent the purifier from operating.
If the ballast is plugged-in without a lamp or if the lamp fails, the ballast's lamp-out protection will prevent the
ballast from operating.
To reset:
•
•
•
Lamp replacement is recommended every 10,000 hours of operation, approximately 12 months of continuous service.
CONNECT lamp OR REPLACE failed lamp.
After 2 minutes, plug the ballast back into the outlet receptacle; it should resume proper operation.
The ballast must remain unplugged for two (2) minutes to reset.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LAMP INSTALLATION OR REPLACEMENT
Figure 3 - Lamp Replacement
Step 2 - Remove End-Cap
Step 3 - Withdraw Lamp
Step 4 & 5 - Remove Sockets
Step 6 - Remove Lamp
1. Disconnect power to water purifier.
2. Remove both easy-off end caps by pulling each cap off static gland nut. Slide each end cap along the wire away
from the socket.
3. Carefully withdraw lamp approximately 2 inches from chamber while feeding lamp socket and lead wire on
opposite end of chamber.
4. While holding lamp end, carefully remove lamp socket on end now exposed.
5. Next, carefully slide lamp back into chamber, until approximately 2 inches of the lamp is exposed on the opposite
end. Hold lamp and remove lamp socket.
6. Lamp should now be disconnected on both ends. Carefully remove lamp from chamber. Be sure to withdraw
lamp straight out without angling until completely clear of quartz sleeve.
!
CAUTION: Lamp and quartz sleeve are easily damaged. Exercise care when removing or
replacing lamp.
7. Reinstall lamp in reverse order.
!
WARNING: Germicidal ultraviolet rays are harmful to eyes and skin. Do not restore power to
water purifier until lamp and both easy-off end caps have been properly reinstalled.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
QUARTZ SLEEVE CLEANING OR REPLACEMENT
Figure 4 - Quartz Sleeve Cleaning or Replacement
Step 4 - Remove Gland Nuts
Step 5 - Remove Washer & O-Ring
Step 6 - Remove Quartz Sleeve
1. Disconnect power to water purifier.
2. Shut off water supply to water purifier via inlet and outlet shut off valves. Drain chamber by removing
drain plug. Once the chamber is completely drained, remove any old sealing tape from the threads of the drain
®
plug, rewrap with 1/2" wide Teflon thread sealing tape, reinstall and tighten the drain plug.
3. Follow the steps in “Lamp Installation or Replacement” to remove lamp.
!
CAUTION: Lamp and quartz sleeve are easily damaged. Exercise care when removing or replacing lamp.
4. Unscrew static gland nuts from each end of the chamber. Avoid striking quartz sleeve with static gland nut.
5. Remove Teflon washer and o-ring from both ends of quartz sleeve. Teflon washer will sometimes remain with
®
®
®
in the static gland nut. If so, remove Teflon washer from static gland nut before proceeding.
6. Carefully remove quartz sleeve from chamber. NOTE: It is advisable to support the quartz sleeve on the opposite
end with your finger so that it does not drop to the bottom of the chamber as it slides into the chamber.
7. Once the quartz sleeve is removed, clean with alcohol or a mild, non-abrasive detergent. Stubborn stains usually
can be removed with a dilute hydrochloric acid. NOTE: Follow all manufacturer’s instructions and precautions
when handling chemicals.
8. Reassemble in reverse order. Make sure the quartz sleeve protrudes an equal distance past each threaded nipple. Be
®
sure o-rings are placed on quartz sleeve before Teflon washer.
9. Tighten static gland nuts firmly by hand only, DO NOT USE HAND TOOLS. Tightening with hand tools is likely
to cause quartz sleeve to break.
10. Slowly restore water supply to water purifier and check for leaks.
11. If no leaks occur, reinstall lamp, following the steps in “Lamp Installation or Replacement” section.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT OF BROKEN QUARTZ SLEEVE
!
CAUTION: Broken Quartz is SHARP. It is recommended that protective goggles and gloves
are worn when handling broken quartz sleeves.
1.
2.
Disconnect power to water purifier.
Shut off water supply to the water purifier via the inlet and outlet shut off valves. Drain the chamber by
removing the drain plug. Once the chamber is drained, remove any old sealing tape from the threads of the
®
drain plug, rewrap with 1/2" wide Teflon thread sealing tape, reinstall and tighten the drain plug.
3.
4.
Follow the steps in “Lamp Installation or Replacement” to remove lamp.
To prevent damage to the electrical components, it is necessary to separate the ballast housing from the
purifier chamber.
•
On MightyPure™ Models MP13A, MP16A, and MP22A, the ballast housing is mounted to the purifier
chamber using four (4) No. 8 x 3/8" long screws. Using a Phillips cross point screwdriver, carefully
remove the four (4) screws, from along the sides of the ballast housing, and set aside. Separate the
housing from the chamber.
•
On MightyPure™ Models MP36C, and MP49C , the ballast housing is mounted to the purifier
chamber using four (4) 1/4"-20 x 3/8" long hex head bolts. Using a 7/16" wrench or an adjustable wrench,
carefully remove the four (4) bolts with the lock and flat washers, from along the top of the ballast housing,
and set aside. Separate the housing from the chamber.
•
5.
Keep ballast housing and mounting hardware in a clean, dry area.
®
Unscrew static gland nuts from each end of the chamber. Remove Teflon washer and o-ring from both ends
®
of quartz sleeve. Teflon washer will some times remain within the static gland nut. If so, remove Teflon
washer from static gland nut before proceeding.
6.
7.
Carefully remove as much of the broken quartz sleeve as possible, from each end of the chamber.
To remove fragments of quartz sleeve, hold the purifier vertically and shake. The quartz fragments will
break and drop out of the purifier through the gland fitting. Flush water through chamber being careful to
remove all quartz fragments from the interior of the chamber.
8.
9.
10.
Carefully discard all pieces of the broken quartz sleeve.
Align the end of the replacement quartz sleeve with the gland fitting of the chamber.
Carefully slide the quartz sleeve into the chamber, guiding it through the gland fitting. NOTE: Use care to
keep the quartz sleeve parallel to the chamber. Angling the quartz sleeve in any direction could result in the
breakage of the quartz sleeve.
11.
As the quartz sleeve nears the far end of the chamber, support the quartz sleeve by inserting your finger
through the far end gland fitting and into the quartz sleeve. This will minimize the possibility of breaking the
quartz sleeve as it passes through the gland fitting.
12.
13.
Center the quartz sleeve in the chamber, making sure the quartz sleeve protrudes an equal distance past each
threaded gland fitting, of the chamber.
®
Re-install o-rings, Teflon washers, and static gland nuts. Be sure o-rings are placed on quartz sleeve before
®
Teflon washer. Tighten static gland nuts firmly by hand only, DO NOT USE HAND TOOLS. Tightening
with hand tools is likely to cause quartz sleeve to break.
14.
Re-assemble ballast housing to purifier chamber, using hardware removed in Step 4.
NOTE: When re-assembling ballast housing to purifier chamber, electrical power cord should exit ballast
housing from the end mounted opposite the drain plug.
15.
16.
When all connections are complete, allow water to enter the water purifier at a low flow rate until the purifier
is pressurized. With the purifier pressurized, it should be checked for leaks.
See “Lamp Installation or Replacement” section to properly re-install the lamp into the
water purifier.
DISPOSAL OF MERCURY ADDED LAMPS
Germicidal ultraviolet lamps, like standard fluorescent lamps contain small amounts of mercury. Mercury added
lamps should not be placed in the trash. Dispose of properly.
For further information regarding the disposal and recycling of lamps containing mercury, along with Federal and State
“PDF Library for Ster-L-RayTM germicidal Ultraviolet Lamps” section of http://www.ultraviolet.com.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
™
OPTIONAL GUARDIAN
ULTRAVIOLET MONITOR SENSOR PROBE CLEANING
Figure 5 - Ultraviolet Monitor and Sensor Probe
If after cleaning the quartz sleeve, there is no significant improvement in the ultraviolet intensity, as shown on the
intensity meter, it may be necessary to clean the Ultraviolet Monitor's sensor probe. The sensor probe body mounts in a
fitting, located in the center of the disinfection chamber, and protrudes into the chamber.
1. Disconnect power to the water purifier.
2. Shut off water supply to the water purifier via the inlet and outlet shut off valves. Drain the chamber by
removing the drain plug. Once the chamber is drained, remove any old sealing tape from the threads of the
®
drain plug, rewrap with 1/2" wide Teflon thread sealing tape, reinstall and tighten the drain plug.
3. Disconnect power to the Ultraviolet Monitor; remove from chamber by loosening the two setscrews on the
aluminum collar and lifting it free from probe body.
4. Unscrew the sensor probe and remove from the chamber.
5. Remove the quartz rod retainer cap, from the probe body. Take care not to damage the quartz rod, o-ring or the
threads of the probe body.
NOTE: It is recommended, when servicing the sensor probe, to work in a clean, dry area.
6. Once the quartz rod is removed, clean with alcohol or a mild detergent, and rinse with clean water. Stubborn
stains usually can be removed with a dilute hydrochloric acid. NOTE: Follow all manufacturer's instructions
and precautions when handling chemicals. Once the quartz rod has been cleaned, handle the rod by the sides,
to avoid getting fingerprints on the quartz rod faces.
7. Clean the probe body, by removing any dirt or deposits on all surfaces. O-rings should be inspected and can be
replaced if worn or damaged.
8. Reassemble, replacing the o-ring, quartz rod and securing in place with the quartz rod-retaining cap. Tighten
the quartz rod-retaining cap by hand only, DO NOT USE HAND TOOLS. Tightening with hand tools my
damage the quartz rod or o-ring seal.
9. Reinstall sensor probe into the center fitting of the chamber and tighten.
10. Slowly restore water supply to the water purifier, pressurize, and check for leaks. Once it is determined
that there are no leaks, inlet valve can be fully opened.
11. Reposition Ultraviolet Monitor on probe body and tighten setscrews.
12. Restore power to the water purifier and ultraviolet monitor.
If after the cleaning of the sensor quartz rod, there is still no significant improvement in the ultraviolet
intensity, as shown on the intensity meter, proceed to the “Troubleshooting” section.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
!
CAUTION: Always disconnect power to the water purifier, before performing any service.
IMPORTANT: This unit is to be serviced ONLY by qualified, and appropriately licensed, personnel.
Table 3 - Troubleshooting
Problem
Possible Cause
Corrective Action
No electrical power…
Verify that the purifier is connected to a live power source.
Ballast
Lamp-out Protection
Disconnect the purifier from utility power. Replace lamp.
The purifier must remain disconnected from power for
Purifier not operating.
(MP16A, MP22A & MP36C) two (2) minutes to reset.
Cracked or broken
quartz sleeve…
Shut down purifier, drain, and replace quartz sleeve.
See “Quartz Sleeve Cleaning or Replacement” in the
“Maintenance” section.
Water leaking into/from
purifier.
Quartz sleeve sealing
o-ring (s) worn, damaged…
Shut down purifier, drain, and remove static gland nut,
replace sealing o-ring. See “Quartz Sleeve Cleaning or
Replacement” in the “Maintenance” section.
Poor, or loose, connections
or fittings…
Tighten suspect connection or fitting; or shut down
purifier, drain, and remove fitting or connection.
Clean threads; reapply thread sealing tape and reinstall.
Quartz sleeve fouled…
Clean quartz sleeve, see “Quartz Sleeve Cleaning
or Replacement” in the “Maintenance” section.
Sensor Probe, if equipped,
lens fouled…
Clean lens or Quartz Rod, see “Optional Ultraviolet
Monitor Sensor Probe Cleaning” in the “Maintenance”
section.
Poor purifier performance
AND/OR Low UV intensity
Germicidal lamp output
depreciating…
Replace lamp, as it nears its end of life (EOL). See
“Lamp Replacement” in the “Maintenance” section.
(As indicated on Optional
Guardian™
Germicidal lamp not
functioning…
Replace lamp. See “Lamp Replacement” in the
“Maintenance” section.
Ultraviolet Monitor).
Low input voltage…
Verify input voltage to purifier.
Change in water quality…
Have water tested to confirm that it does not exceed
maximum recommended concentration levels for use
with this purifier.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Table 4 - Technical Specifications
Model:
MP13A
MP16A
MP22A
MP36C
MP49C
Flow Rate (GPM):
Inlet\Outlet Size:
Number of Lamps:
Lamp Model No.:
Length:
2
3
6
12
20
1
3
3
1
2
4
4
2
/ "m NPT
/ "m NPT
/ "m NPT
1"m NPT
1
1- / "m NPT
1
1
1
1
GPH212T5L
GPH287T5L
GPH436T5L G36T6L
G48T6L
1
1
1
1
1
2
2
2
2
2
13- / "
16- / "
22- / "
36- / "
49- / "
5
5
5
11
11
16
16
16
16
16
Width:
4- / "
4- / "
4- / "
5- / "
5- / "
3
3
3
1
1
8
8
8
2
2
Height:
8- / "
8- / "
8- / "
9- / "
9- / "
1
1
1
1
1
4
4
4
4
4
Chamber Diameter:
Shipping Weight:
Voltage:c
4- / "
4- / "
4- / "
4- / "
4- / "
12 Lbs
120V
.17A
12 Lbs
120V
14 Lbs
120V
22 Lbs
120V
36 Lbs
120V
Amps:
.23A
.33A
.65A
.42A
Frequency:
60Hz
60Hz
60Hz
60Hz
60Hz
Power Consumption:d 14 Watts
Lamp Watts: 10 Watts
Max Operating Pressure: 100 PSI
18 Watts
14 Watts
100 PSI
24 Watts
20 Watts
100 PSI
44 Watts
39 Watts
100 PSI
54 Watts
50 Watts
100 PSI
Ambient Temperature: 33° F - 100° F 33° F - 100° F 33° F - 100° F 33° F - 100° F 33° F - 100° F
Quartz Sleeve:
Drain Plug:
1
1
1
1
1
1
1
1
1
1
4
4
4
4
4
/ " NPT
/ " NPT
/ " NPT
/ " NPT
/ " NPT
Lamp Out
Indicator:
Translucent
Sight Port
Translucent
Sight Port
Translucent
Sight Port
Translucent
Sight Port
Translucent
Sight Port
Ultraviolet Monitor:
Audio Alarm:
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Solenoid Valve:
Time Delay Mechanism: Optional
Elapsed Time Indicator: Optional
Quantum
Optional
Thermal Optimizer:
c
d
220V 50Hz, 220V 60Hz, 12V, or 24V DC units are also available. Consult Factory for specific voltage requirements.
Total power consumption, including ballast loss.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL ACCESSORIES
Optional accessories are available for operation at 120v 60Hz or 220v 50Hz, unless specified.
Please specify. Consult Factory for 12v DC or other special input power requirements.
Table 5 - Optional Accessories
Optional Accessories
Available for:
Guardian™ Ultraviolet Monitor - Analog/Digital
Sentry™ Safety Sensor
MP13A through MP49C
MP13A through MP49C
MP13A through MP49C
MP13A through MP49C
MP13A through MP49C
MP13A through MP49C
MP13A through MP49C
MP13A through MP49C
Steralert™
Audio Alarm
Elapsed Time Indicator Universal Input
Wall Mounting Kit
Time Delay Mechanism
Quantum Thermal Optimizer:
Solenoid Valve - Nylon (120v only)
1
2
3
4
MP13A ( / ") through MP22A ( / ") c
MP36C (1") c
1
3
2
4
MP13A ( / ") through MP22A ( / ")
Solenoid Valve - Brass
MP36C (1")
1
2
MP49C (1- / ") c
1
2
MP49C (1- / ")
1
2
MP13A ( / ")
3
4
MP16A ( / ")
3
4
Flow Control Valve d
MP22A ( / ")
MP36C (1")
1
2
MP49C (1- / ")
c
d
Valve requires 10-PSI pressure drop for satisfactory operation.
Unless otherwise specified PVC flow control valves are supplied. All PVC and Stainless
Steel flow control valves are male NPT. Consult Factory for other flow control valves.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
™
Mighty Pure Models MP13A, MP16A & MP22A
Figure 6 - Exploded View MP13A, MP16A & MP22A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6 - Replacement Parts MP13A, MP16A & MP22A
ITEM
NO. DESCRIPTION
MP13A
PART NO.
MP16A
PART NO.
MP22A
QTY PART NO.
QTY
QTY
1
2
Easy-Off End Cap
Rubber O-ring, Static Gland
Lamp Spacer
2
2
2
2
1
2
2
2
1
1
1
2
1
1
2
1
4
1
1
1
-
25-1499A1
00-1108B
25-0208A
05-1219B2
05-1400
25-1492D
25-1235A
00-1238A
15-1110A
30-1075
27-1216
50-1314
10-1070
10-1074
50-0155
25-1104A
50-1323
25-1465E1
35-1100
35-1452
-
2
2
2
2
1
2
2
2
1
1
1
-
25-1499A1
00-1108B
25-0208A
05-1219B2
05-1098
25-1492D
25-1235A
00-1238A
15-1111A
30-1075
27-1216
-
2
2
2
2
1
2
2
2
1
1
1
-
25-1499A1
00-1108B
25-0208A
05-1219B3
05-1097
25-1492D
25-1235A
00-1238A
15-1112A
30-1075
27-1216
-
3
4
Lead Wire & Socket
Lamp
5
6
Static Gland Nut
®
7
Teflon Washer
8
Rubber O-ring, Quartz Sleeve
Quartz Sleeve
9
10
11
12
13A
13B
14
15
16
17
18A*
18B*
19
Sight Port Plug
Drain Plug
Speed Nut, 6-32
Ballast, 120v 60Hz
Ballast, 220v 50Hz
Screw, Mounting
1
1
4
1
4
1
1
1
2
10-1327
10-1327
50-0155
25-1105B
50-1323
25-1465E2
35-1100
35-1452
50-0107
1
1
4
1
4
1
1
1
2
10-1036
10-1036
50-0155
25-1544D
50-1323
25-1465E3
35-1100
35-1452
50-0107
Ballast Housing
3
8
Screw, No. 8 x / " long
Chamber
Line Cord, (120v 60Hz)
Power Cord 6’ (220v 50Hz)
Standoff, Mounting
* not depicted in drawing
17
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
™
Mighty Pure Models MP36C & MP49C
Figure 7 - Exploded View MP36C & MP49C
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
NO. DESCRIPTION
MP36C
PART NO.
MP49C
PART NO.
QTY
QTY
1
2
3
4
5
6
7
Easy-Off End Cap
Rubber O-ring, Static Gland
Lamp Spacer
2
2
-
25-1499A1
00-1108B
-
2
2
2
2
1
2
25-1499A1
00-1108B
25-0209A
05-1218A2
05-1334
Lead Wire & Socket
Lamp
2
1
2
05-1218A2
05-1343
25-1492D
Static Gland Nut
25-1492D
®
Teflon
19
USER ASSISTANCE
Atlantic Ultraviolet Corporation
375 Marcus Boulevard
Hauppauge, New York, 11788
Atlantic Ultraviolet Corporation
makes every effort to ensure that
the MightyPure™ Ultraviolet
Water Purifiers are products of
superior quality and workmanship.
This manual describes the installa-
tion, operation and maintenance of
the MightyPure™ Ultraviolet
Water Purifiers.
Please read and become familiar
with the contents of this manual
before installing or using this unit.
If after reading the manual you still
have questions, or concerns,
regarding the installation or use of
this unit, contact our offices, week-
days between 8:30 am and 5:00 pm
Eastern time, at:
Tel: 631.273.0500
Fax: 631.273.0771
E-mail: [email protected]
Please fill out and return the Owner Registration card immediately. If the card is missing from this manual,
please contact any of our application specialists to obtain one.
Atlantic Ultraviolet Corporation takes all possible precautions when packaging equipment to prevent damage.
Carefully inspect and report all damage. Do not install damaged equipment. Follow all instructions on any labels
or tags. Carefully inspect all packing materials before discarding to prevent the loss of accessories, mounting
hardware, spare parts or instructions.
For your convenience, record the following information below. The model and serial number can be found on
a label located on the MightyPure™ Ultraviolet Water Purifiers. Keep this manual, along with proof of
purchase, handy when contacting our offices.
Purchased From:
Model:
Date:
Serial No.:
WARRANTY
We warrant that this product will be free from defects in material and workmanship for a period of one year
from the date of shipment thereof or the product’s total rated life, whichever first occurs. Within the warranty
period we shall repair or replace such products, which are returned to us with shipping charges prepaid, and
which are determined by us to be defective. This warranty will not apply to any product, which has been sub-
jected to misuse, negligence, or accident; or misapplied; or modified; or repaired by unauthorized persons; or
improperly installed.
The Buyer shall inspect the product promptly after receipt and shall notify us at our main office in writing of
claims, including claims of breach of warranty, within thirty (30) days after the Buyer discovers or should have
discovered the facts upon which the claim is based. Failure of the Buyer to give written notice of a claim within
the time period shall be deemed to be a waiver of such claim.
The provisions of the above warranty are our sole obligation and exclude all other remedies or warranties,
expressed or implied, including warranties of merchantability and fitness for a particular purpose, whether or not
purposes or specifications are described herein. We further disclaim any responsibility whatsoever to the cus-
tomer, or to any person, for injury to person, damage to, or loss of property or value caused by any product
which has been subjected to misuse, negligence, accident; or modified or repaired by unauthorized persons; or
improperly installed.
Under no circumstances shall the Company be liable for any incidental, consequential or special damages,
losses or expenses arising from the contract for this product, or in connection with the use of, or inability to use,
our product for any purpose whatsoever.
PATENT NOTICE
No attempt has been made to determine the patent status of applications illustrated or described in this publi-
cation. Inclusion in this publication of any design or method of use, which may be patented, is not to be con-
strued as promoting or sanctioning unauthorized use.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|