TEAM PRODUCTS INTERNATIONAL INC. Limited Warranty
WhAT IS COvERED: Any defect in materials and workmanship.
FOR hOW LONg: 2 years from date of purchase.
WhAT WE WILL DO: If your product is defective and returned within 30 days
after the date it was purchased, we will replace it at no charge to you. If
returned after 30 days but within 2 years of the date of purchase we will
repair it or, at our option, replace it at no charge to you.
If we repair your product, we may use new or reconditioned replacement
parts. If we choose to replace your product, we may replace it with a
new or reconditioned one of the same or similar design. The repair or
replacement will be warranted under our standard 2 year warranty.
LIMITATIONS: IMPLIED WARRANTIES, INCLUDINg ThOSE OF FITNESS FOR A
PARTICULAR PURPOSE AND MERChANTAbILITy (AN UNWRITTEN WARRANTy
ThAT ThE PRODUCT IS FIT FOR ORDINARy USE), ARE LIMITED TO 2 yEARS
FROM DATE OF PURChASE. WE WILL NOT PAy FOR LOSS OF TIME, INCONvE-
NIENCE, LOSS OF USE OF yOUR PRODUCT OR PROPERTy DAMAgE CAUSED
by yOUR PRODUCT OR ITS FAILURE TO WORk, OR ANy OThER INCIDENTAL
OR CONSEqUENTIAL DAMAgES INCLUDINg PERSONAL INjURy.
1200 WATT
Power Inverter
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages,
so the above exclusions or limitations may not apply to you.
WhAT WE ASk yOU TO DO: To get warranty service for your product,
you must provide proof of the date of purchase. Within 30 days of the
date it was purchased, return your product to your place of purchase for
immediate replacement. After 30 days, but before the end of the 2 year
warranty period, you may return the product to the following address:
TEAM PRODUCTS INTERNATIONAL INC.
Attn: Customer Service Returns
35 A Continental Drive
Wayne, Nj 07470
We suggest that you retain your original packing material in the event
you need to ship your product. When sending your product include your
name, address, phone number, proof of date of purchase, and a
description of the operating problem. After repairing or replacing your
product, we will ship it to your home or office within four weeks.
Owner’s Manual
PMP1200 Models
WhAT ThIS WARRANTy DOES NOT COvER: Among oTher ThIngS ThIS
WArrAnTy doeS noT cover defecTS reSulTIng from AccIdenTS,
dAmAge WhIle In TrAnSIT To our ServIce locATIon, AlTerATIonS,
unAuThorIzed repAIr, fAIlure To folloW InSTrucTIonS, mISuSe, fIre,
flood, And AcTS of god. If your producT IS noT covered by our
WArrAnTy, cAll our cuSTomer ServIce number AT (888) 231-4022 To
deTermIne WheTher We WIll repAIr your producT And oTher repAIr
InformATIon, IncludIng chArgeS. We, AT our opTIon, mAy replAce
rATher ThAn repAIr your producT WITh A neW or recondITIoned
one of The SAme or SImIlAr deSIgn. The repAIr or replAcemenT WIll
be WArrAnTed for 2 yeArS.
ThIS lImITed WArrAnTy IS The only one We gIve on your producT,
And IT SeTS forTh All our reSponSIbIlITIeS regArdIng your producT.
There Are no WArrAnTIeS WhIch exTend beyond The deScrIpTIon SeT
forTh Above.
©2006 The Coleman Company, Inc. All rights reserved.
STATE LAW RIghTS: This warranty gives you specific legal rights and you
may also have other rights which may vary from state to state.
COLEMAN® and
are registered trademarks of The Coleman Company, Inc., used under license. Designed in the USA and
custom-manufactured in China for Team Products International Inc. Distributed byTeam Products International Inc., Mountain Lakes, NJ 07046.
PMP1200033106-82
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual
PMP1200 Models
Notes
Connecting the Inverter
• Loose connections can result in a severe decrease in voltage, which may cause
damage to the component or the product you wish to operate.
When connecting the inverter to the power source, it is recommended to use
the thickest wire available in the shortest length possible. If the inverter and the
battery are positioned within 4 feet of each other, a minimum of #2 gauge wire
should be used to make the connections. When the distance between them is
4 to 6 feet, a minimum of #0 gauge wire is required. When separated by more
than six feet, always use #00 gauge wire.
• Failure to make a proper connection between the inverter and the power
source may result in reverse polarity. Reverse polarity will blow the internal
fuses in the inverter and may cause permanent damage to the inverter.
Damage caused by reverse polarity is not covered under the warranty.
Use of #0 gauge wire to make the connections to the inverter may require a “0
to 4 Gauge Adaptor”. This adaptor is available through most electrical supply
stores.
•The audible alarm may make a momentary “chirp” when the inverter is turned
ON(I) or OFF(O). This same alarm may also sound when the inverter is being
connected to or disconnected from the 12-volt power source. This is normal.
1. Make sure the ON/OFF power switch located on the front panel of the inverter
is in the OFF(O) position.
• If the LED Indicator Light blinks when you first turn the inverter ON(I), this may
indicate an interruption of the power supply. Simply turn the inverter OFF(O)
and try removing and reconnecting the clamps. If this does not fix the
problem, try using a different 12-volt power source.
2. Using a Phillips screwdriver, loosen the set screws in the red (+) and black (-)
power input terminals
• If using more than one appliance, do not exceed a combined total of
1200 watts.
3.The cables should be stripped approximately 5/8”.
4. Connect the cable wires to the power input terminals making sure to match
the color coded cables to the color coded terminals on the inverter (RED=
Positive, BLACK = Negative). Tighten the set screws to secure the cables. Be
sure not to over tighten these screws. Note: A secure connection is essential
to proper operation of the inverter.
Source of Power
Most automobile and marine batteries will provide an ample power supply to
the inverter for 30 to 60 minutes even when the engine is turned off. Actual
time may vary depending on the age and condition of the battery and the power
demand being placed on it by the equipment being operated.
5. Connect the cable from the Positive (+) terminal (RED) on the inverter to the
Positive terminal on the power source. Double check that the connection is
secure.
If you decide to use the inverter while the engine is off, we recommend that
you start the engine every 30 to 60 minutes and let it run for approximately
10 minutes to recharge the battery. It is also recommended that the device
plugged into the inverter be turned OFF before starting the vehicle engine.
6. Locate the Ground LugTerminal at the rear of the inverter. Run a wire from
this terminal to a proper grounding point using the shortest practical length.
It is recommended to use a minimum of 12 AWG wire.You can connect
this wire to the chassis of your vehicle or to the grounding system in your
boat. As an alternative, when in remote locations the ground wire can be
connected to the earth (one way to accomplish this is to attach the wire to a
metal rod driven into the ground). Before connecting to the ground, make
certain that the inverter is turned off. Operation the inverter without correctly
grounding the unit may result in electrical shock.
Although it is not necessary to disconnect the inverter when starting the vehicle
engine, it may momentarily cease to operate as the battery voltage decreases.
When the inverter is not supplying power, it draws very low amperage from the
battery. It is recommend that the inverter always be disconnected when not in
use.
7.Turn the inverter power switch to the ON(I) position. The LED Indicator Light
should illuminate GREEN to confirm that power is running to the inverter.
Note: Always disconnect the power inverter from the 12-volt power source and
8.Turn the inverter power switch to the OFF(O) position. (The LED Indicator
Light may “blink” briefly and/or the internal audible alarm may make a
momentary “chirp”. This is normal).
make sure the inverter is turned OFF before replacing the fuse.
Safety and Usage Precautions
• For best operating results, place the inverter on a flat surface
• Keep inverter dry. Do not expose inverter to rain or moisture.
9. Make sure that the device you intend to operate is turned OFF. Plug the cord
from the equipment you wish to operate into one of the AC outlets located on
the front panel of the inverter.
• DO NOT operate the inverter if you, the inverter, the device being operated, or
any surface that may come into contact with the inverter are wet. Water and
other liquids can conduct electricity, which may lead to serious injury
or death.
10.Turn the inverter power switch to the ON(I) position. Then turn the
equipment on.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual
PMP1200 Models
• Avoid placing the inverter on or near heating vents, radiators or other
sources of heat. Do not place or use the inverter in direct sunlight. Ideal air
temperatures should be between 50° and 80° F.
Television and Audio Suggestions
Although all COLEMAN® inverters are shielded and filtered to minimize
signal interference, some interference with your television picture may be
unavoidable, especially with weak signals. However, here are some
suggestions that may improve reception:
• In order to properly disperse the heat generated from the inverter while it is
operating, keep the inverter well ventilated. Keep the area surrounding the
inverter clear while in use.
• Make sure the television antenna produces a clear signal under normal
operating conditions (at home plugged into a standard 120 volt AC outlet).
Also, ensure that the antenna cable is properly shielded and/or good quality.
• Do not use the inverter near flammable materials. Do not place the inverter in
areas such as battery compartments where fumes or gases may
accumulate.
• Change the positions of the inverter, antenna cables and the television power
cord.
Inverter Protection Features
• Isolate the television, its power cord and antenna cables from the 12-volt
power source by running an extension cord from the inverter to the
television set.
• Short Circuit Protection. The inverter will automatically shut down until
short is removed.
• Low Voltage Alarm. An alarm will sound when the voltage from the battery
discharges to 10.5 +/- 0.5 volts DC. This is an indication that the battery needs
to be recharged.
• Coil the television power cord and the input cables running from the 12-volt
power source to the inverter.
• Attach an AC interference filter or similar product between the inverter and the
television power cord. These filters are available at most electronic supply
stores, including Radio Shack.
• Over Voltage Protection. The RED LED Indicator Light will illuminate and
the inverter will automatically turn itself off when the input exceeds 16.5 +/- 1
volt DC.
• Under Voltage Protection. The RED LED Indicator Light will illuminate and
the inverter will automatically turn itself off when the input is less than 10.0
+/- 0.5 volts DC.
Note: Inexpensive sound systems may emit a “buzzing” sound when
operated with an inverter. This is due to the inadequate filters in the sound
system. There is no solution to this problem other than purchasing a sound
system with a higher quality power supply.
• Overload Protection. The RED LED Indicator Light will illuminate and the
inverter will automatically turn itself off when the continuous draw of the
equipment being operated exceeds 1200 watts or the surge draw of the
equipment exceeds 2400 watts.
• Thermal Protection. The RED LED Indicator Light will illuminate and the
inverter will automatically turn itself off when the circuit temperature
exceeds 150° F.
Notes
•The inverter is equipped with a cooling fan, which is designed to turn on when
the unit gets hot. Automatic shut down of the unit caused by high circuit
temperatures will occur when the cooling fan is unable to maintain a cool
enough temperature for safe operation.
• In the event of automatic shut down or a continuous audible alarm, turn the
inverter power switch to the OFF(O) position until the source of the problem
has been determined and resolved.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual
PMP1200 Models
Troubleshooting
Troubleshooting
PROBLEM: Low or No Output Voltage
Reason
PROBLEM:TV Interference
Reason
Solution
Solution
Electrical interference from
the inverter.
Add an AC interference filter on
to theTV power cord. Refer
toTV and audio section of
this manual.
Poor contact with
battery terminals.
Clean terminals
thoroughly. Reattach
battery clips.
Using incorrect type of
voltmeter to test
output voltage.
Use true RMS reading meter.
PROBLEM: Low Battery Alarm On AllTheTime
Reason
Solution
Input voltage below 10.5 0.5 volts.
Keepinputvoltageabove10.5 0.5
volts to maintain regulation.
PROBLEM: Red LED On
Reason
Solution
Poor or weak
Recharge or
Battery voltage below
10.0 0.5 volts.
Recharge or replace battery.
battery condition.
replace battery.
Inadequate power being
delivered to the inverter
or excessive voltage drop.
Make sure connection is secure.
Use lower gauge wire. Keep
wire length as short as possible.
Equipment being operated
draws too much power.
Use a higher capacity inverter
or do not use this equipment.
PROBLEM:TV Does Not Work
Inverter is too hot (thermal
shutdown mode).
Allow inverter to cool.
Check for adequate ventilation.
Reduce the load on the
inverter to rated continuous
power output
Reason
Solution
TV does not turn on.
Try turning the inverter
ON/OFF/ON.
ContactTV manufacturer for
start up surge and power
consumption.
Unit may be defective.
See Warranty and call
Customer service at
1-888-231-4022.
A larger inverter may
be required.
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual
PMP1200 Models
In Review
Specifications:
Maximum Continuous Power
Surge Capacity (Peak Power)
Max Power Efficiency
Waveform
• Never attempt to operate the inverter from any other power source other than
a 12-volt battery.
1200 Watts
2400 Watts
• When connecting and using the inverter, make sure that the inverter is
positioned far away from any potential source of flammable fumes or gases.
>85%
Modified Sine Wave
<0.8A
• Make certain that the power consumption of the equipment you wish to
operate is compatible with the capacity of the inverter. Do not exceed
1200 watts in total power, or 2400 watts for each individual AC outlet.
No Load Current Draw
Input Voltage Range
AC Receptacles
11-15VDC
• When attempting to operate battery chargers, monitor the temperature of the
battery charger for approximately 10 minutes. If the battery charger
becomes abnormally warm, disconnect it from the inverter immediately.
120V AC, Grounded
6 x 25 amp (spade type)
6.2 lbs.
Fuse
• Use only 25 amp spade type fuses for the inverter.
Weight
• When operating the inverter with an automobile or marine battery, start the
engine every 30 to 60 minutes and let it run for approximately 10 minutes to
recharge the battery.
Dimensions
10.7” (L) x 8.4”(W) x 3.1” (H)
271.78mm(L) x 213.36mm(W) x 78.74mm(H)
• In the event of a continuous audible alarm or an automatic shut down of the
unit, turn the inverter OFF immediately. Do not turn the inverter ON again
until the source of the problem has been identified and corrected.
Questions?
•To avoid battery drain, always disconnect the inverter when not in use.
• Do not expose the inverter to rain or moisture.
If you have any questions about this product, please contact our Customer
Service Department at (888) 231-4022, Monday through Friday, 9 AM to 5 PM
• Avoid placing the inverter near sources of heat or in direct sunlight.
• While in use, make sure that the inverter is properly ventilated.
• For best operating results, make sure the unit is placed on a flat surface.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|