Trail Camera
Instruction Manual
Model #: 119256CW
03-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Page Index
Introduction
5
6-7
8
9
9
Parts & Controls Guide
Battery and SD Card Installation
About the Setup Menu
Using the Setup Menu
SETUP MENU REFERENCE TABLE
Camera Operation
10-11
12
Mount the Camera
12
12
13
13
Power on the Camera
Test the Coverage Area
Secure the Camera
Viewing the Photos and Videos
Glossary
Technical Specifications
Troubleshooting/FAQ
14
15
16
17-20
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTE
Congratulations on your purchase of one of the best trail cameras on the
market! Tasco is very proud of these cameras and we are sure you will
be pleased with yours as well. We appreciate your business and want to
earn your trust. Please refer to the notes below and the instructions in
this manual to ensure that you are completely satisfied with this product.
If your Tasco Trail Cam does not seem to be functioning properly
or if you are having photo/video quality issues, please check the
Troubleshooting/FAQ section on pages 17-20.
Problems are often due to something simple that was overlooked, or
require only changing one setting to solve.
If your problem continues after trying the solutions in the
Troubleshooting/FAQ section, please call Tasco Customer Service at
(800) 423-3537. In Canada, call (800) 361-5702.
Tasco recommends using 4 Energizer® Lithium AA batteries in this Trail
Cam to obtain maximum battery life.
Do Not Mix Old and New Batteries
Do not mix battery types-use ALL lithium or ALL alkaline.
Rechargeable batteries are not recommended.
Tasco recommends using SanDisk® SD and SDHC Cards
(up to 32GB capacity) in this Trail Cam.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase of a Tasco Digital Trail Camera. This
camera is designed to record animal activity in the outdoors with its still
image and movie modes and weatherproof, rugged construction. Your
trail cam features a compact, portable size and an extra long battery life.
Main Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.3 MP digital sensor
Compact Size (120mm*94mm*46mm)
Long Battery Life (Up to 6 months)
Trigger Time=1.3 seconds or less
Automatic IR Filter
LCD Display
15 Night Vision LEDs
Adjustable Photo Delay: 5~ 59 second ,1~ 10mins (default 10S)
Multiple Shot Mode (3 images per trigger)
640*480 at 30 FPS Videos
Supports up to 32 GB SD Card
Date, Time & Moon Phase Imprint
Auto Exposure
Auto White Balance
Power Supply: 4 AA batteries (lithium or alkaline)
Mounting Socket for Standard Tripods
Weatherproof
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Controls Guide
PIR Motion
Sensor
Camera
Lens
Padlock
Hole
Infrared
LED Array
Tripod
Socket
Front of Camera
PIR
Indicator
(Setup
Mode
Light
Sensor
Only
IR LED Array Detail
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Controls Guide
USB Port
LCD
Display
Power
Switch
SD Card
Slot
Battery
Compartment
Control Panel
(Front Unlatched & Opened)
Control Panel Detail
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY and SD CARD INSTALLATION
YourTasco DigitalTrail Camera is designed to operate using 4 AA batteries.
We recommend using Lithium (for longest life) or Alkaline batteries.
NOTE: Always set the power switch to the OFF position when installing or
removing batteries.
Please make sure the batteries are inserted correctly, as indicated inside
the battery compartment. Incorrect voltage or polarity (+/-) will damage
the camera.
Do not mix old and new batteries.
Do not mix battery types-use ALL lithium or ALL alkaline.
Rechargeable batteries are not recommended.
Memory
Your Digital Trail Camera has a memory card slot, to accept SD cards up to
32GB max. capacity (sold separately).
Inserting an SD card
•
Make sure the power switch is in the OFF position whenever adding
or removing memory.
•
Insert an SD card into the card slot completely and oriented correctly
as shown by the icon above the slot (label up, contacts facing down
and notched corner on the right).
•
To remove the SD memory card, depress the SD card and pull out
the card gently.
Using a new, blank SD card is recommended. If the SD card has been used
in another device, please make sure to format using the Format option in
the Trail Cam’s Setup menu before you set the camera to capture photos/
videos. New cards are ready to use straight from the package.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THE SETUP MENU
Slide the power switch to the On position. You’ll see“WAIT”on the display,
then the setup menu screen. Before you start using the camera, you’ll no
doubt want to set the date/time so they are imprinted correctly on your
photos, and maybe change the trigger delay time and image resolution
to your preferences. This is done by editing the settings of an item listed
in the Setup Menu.
To enter the Setup Menu at any time, press the SETUP button (to left of
the power switch).
USING THE SETUP MENU
The Setup Menu has 5 different items, which appear on a list in the left
frame of the display. Here’s how to edit (change) the setting of a menu
item:
1. Select the menu item you want to edit by pressing the UP or DOWN
button until the item is blinking. Note: you can see the current/
default setting for each item (without changing it) in the main center
frame as you move up and down the list of items.
2. Press the OK button.
3. You can now select the setting you prefer for the selected item by
pressing the UP or DOWN button (do not hold the button down). The
setting displayed in the center frame will blink until you press OK to
confirm it is the setting you want to save.
4. To exit the Setup menu at any time, simply press the Setup button.
SETUP MENU DISPLAY
Battery Level
CURRENT
SELECTED
SETTING OF
MENU
SELECTED ITEM
ITEM
Indicates Photo (1P or 3P) or Movie Mode
9
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table lists all of the menu items, their available settings,
and a description of their functions:
Menu Item
Description/Operation
Settings
(Bold=default)
Date
set year, month, Press OK and use the UP/DOWN
and day
keys (to change the setting), then
press OK again to go to the next
date parameter and repeat, to
set the current year, month, and
day. Press OK after setting the
day to move on and set the Time
(next item)
Time
set hour and
minute
Press OK and use the UP/DOWN
keys (to change the setting) then
OK again ( to move to the next
field) to set the current hour (24-
hr format only, “00”=midnight,
“12”=noon) and minute.
Delay
set minutes (0-
10) or seconds
(5-59)
Default delay
time= 10 sec.
Selects the length of time that
the camera will “wait”until it
responds to any additional
triggers from the PIR after an
animal is first detected and
remains within the sensor’s
range. During this user set
“ignore triggers”interval, the
camera will not capture photos/
videos. This prevents the card
from filling up with too many
redundant images. Settings
begin with 10 second default
time. Press OK, set the delay time
in minutes (if desired), press OK
and set the delay in seconds.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Item
Mode
Description/Operation
Settings
(Bold=default)
1.3M/3M (with
Mode set to
1P or 3P for
photos),
5-60 Sec (in
Movie (video)
mode
Select “Mode”and press OK. Use
UP/DOWN to select 1P (single
photo), 3P (burst of 3 photos), or
Movie (video mode). Press OK.
Use UP/DOWN to set LO (1.3 MP)
or HI (3 MP) still photo resolution
(High resolution provides better
quality photos, low resolution
allows you to store more photos
on the SD card), or video length
from 5-60 sec. (if video mode was
selected).
Format
FO/NO,
Y/N
Deletes (erases) all files stored
on a card to prepare it for reuse.
Always format a card that has
been previously used in other
devices. Caution! Make sure you
have downloaded and backed
up any files on the card that you
want to preserve first! Press UP to
select “FO”, press OK, then select
“Y”(Yes) and press OK again to
confirm you want to format the
card. The extra step and “No”
defaults help prevent accidental
erasure of all your photos/videos.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
When you’ve finished using the Setup Menu, and are ready to return the
camera to normal operating mode, so it will begin to capture photos or
videos for you, simply press the Setup button. After you exit the Setup
Menu, the display will go blank and the camera is in “sleep” mode. About
30 seconds later, the camera will begin taking photos or videos when
triggered, at intervals determined by the trigger delay time setting.
Once your camera has been setup, you are ready to begin using it to
capture photos of activity in the area you choose to locate it. Just follow
these steps:
CAMERA OPERATION
1. Mount the Camera
It is recommended that you mount the camera about 4 or 5 feet (1.2~1.5
meters) off the ground, with the camera pointed at a slight downward
angle. It’s best to avoid mounting the camera facing east or west as the
rising and setting of the sun could produce false triggers and overexposed
images. Clear branches and other debris away from the front of the
camera so as not to block the camera lens or PIR sensor.
To mount the camera in place, insert the strap through the strap slots on
the rear housing. Wrap the strap around the mounting surface. Secure
the strap and tighten the buckle in order to secure the camera.
Make sure that both door latches are securely locked in place, to ensure
proper weather resistance.
2. Power On the Camera
The camera will be in “sleep” status after it has been powered on. When
the PIR sensor is triggered, it will start to take photos immediately after
the delay time (as set) has passed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA OPERATION (continued)
3. Test the Coverage Area
One of the Trail Camera’s most useful features is the ability to test the
coverage area.
•
After mounting the camera, open the front housing and slide
the Power switch to the “ON” position. Press the SETUP button if
necessary to enter the Setup Menu.
•
•
•
The PIR indicator light below the lens will blink when you have
entered the coverage area.
Adjust the camera position as needed and repeat the test until the
desired coverage area is achieved.
Press the SETUP button again when you are finished using the test
mode-the camera will be “sleeping” and waiting for the PIR sensor
to trigger the first photo or video capture.
•
Maximum PIR sensor range is approx. 30 ft.
4. Secure the Camera
A standard padlock may be used in the camera’s lock hole to secure it
and prevent theft.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VIEWING THE PHOTOS and VIDEOS
After your camera has been operating for awhile, you will of course want
to review the photos and/or videos it has been capturing. This can be
done by either of two methods, according to your preference or the
availability of accessory equipment:
Using an SD Card Reader
1. Push the SD card in slightly to release it then pull it out gently.
2. Put the SD card into any of the widely available SD card readers
(either a dedicated SD card reader or “multi-card reader” that
features slots for several different memory cards, including SD cards.
3. Follow the card reader supplier’s directions to view or download the
photo and/or video files on the SD card.
Connecting the Camera to Your Computer via USB
1. Slide the Power switch to the “ON” position, then press the SETUP
button.
2. Connect your camera’s USB port (left side near the display with
camera unlatched and open) to a PC or Mac computer with a USB
cable (not included, available at most electronics/computer retailers)
that has a“Mini-B”USB plug on one end (camera) and a“Standard-A”
USB plug at the other end (computer).
3. The PC will recognize the camera as an external storage device,
using the “USB Mass Storage” standard (no driver installation
necessary-not compatible with Windows 98 or earlier). The PC will
display a new disk symbol under “My Computer” or in Windows
Explorer (Macs-new disk appears on the desktop), and you will see a
dialog window on your desktop with several options to view, move,
or copy the photo and video files that are stored on the SD card.
The camera’s LCD will display “STO”, meaning the camera is in mass
storage mode.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
PIR (Passive Infrared Sensor): Senses motion like a typical security motion
detector. Requires infrared energy (heat) in addition to motion to trigger
the sensor to help limit detection to live subjects (rather than leaves, etc).
Camera Delay: Time elapsed between photos while events are sensed
and recorded. You should set this based on wildlife activity in the area.
Moon Phase: The trail cams have a feature which imprints a moon phase
stamp on each photo for reference.
IR Flash: Also called IR LED Array. This is a “night vision” feature, which
emits a burst of infrared light, invisible to the human eye. Especially
useful for night photos when a visible flash may be undesirable.
Battery Life: Time that camera will function in the field. Dependent on
ambient temperature, number of images taken and number of times the
IR flash fires. When the battery voltage drops below 4.5v, the IR flash stops
firing. When battery voltage is below 3.5v, the camera stops working.
Single/Multi-Image Modes: The number of pictures the camera takes
per PIR trigger (still photo capture mode only).
1P: A single image is captured for each PIR trigger
3P: A three image sequence captured for each PIR trigger
FULL: When the SD card’s memory capacity is full, the LCD display
indicates “FULL”
Mass Storage: Connect the camera with a USB cable to a computer,
press the “SETUP” button, and the computer can access the contents of
the SD card. The camera is automatically recognized as an“external drive”,
without the need to install special drivers. (Win 98 and older operating
systems are not supported. Mac OSX is also compatible-the camera will
appear on your desktop as an external storage device or “disk”).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Model Number
119256CW
Image Sensor Type
Sensor Resolution
1/4 Inch CMOS
1.3 Megapixels
Effective Focal Length
Lens Aperture
IR Filter
7.6 mm
f/2.0
Automatic IR Filter
LCD (menu screen)
Display
PIR Sensor
Yes
Trigger Speed
Number of IR LED
1.3 seconds or less
15 LEDs
Max Night Vision Lighting Distance 30 feet
Storage
SD Card, up to 32 GB Capacity
PIR Indicator
Yes (Setup mode only)
5~ 59 second, 1~ 10mins (default 10S)
LO (1.3 MP) or HI (3 MP*)
Yes-3 photos
Adjustable Delay Time Range
Selectable Image Resolution
Multiple Image Mode
Movie: AVI 640 x 480 pixels @ 30 fps (5-60
seconds).
Video Resolution
File Format (Image/Video)
Date/Time Imprint
Moon Phase Imprint
Exposure
JPEG/AVI
Yes
Yes
Auto
Auto
White Balance Mode
Power Supply
4 AA Cell batteries (alkaline or lithium)
Yes
Water Resistant
*3MP resolution via software interpolation
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting / FAQ
Battery life is shorter than expected
1.
Battery life will vary with operating temperature and the number
of images taken over time. Typically, the trail cam will be able to
capture several thousand images before the batteries die.
Check to make sure you have used new alkaline or lithium
batteries. Tasco recommends using 4 Energizer® Lithium AA
batteries in this Trail Cam to obtain maximum battery life.
Make sure that the power switch was turned to the“ON”position
and that the camera was not left in Setup mode while in the field.
Make sure that you are using a good quality name brand SD card
in your camera. Tasco recommends SanDisk® brand SD Cards
up to 32GB. Our experience indicates that poor quality SD cards
can sometimes reduce your trail cam battery life.
2.
3.
4.
Camera stops taking images or won’t take images
1.
2.
3.
4.
5.
6.
Please make sure that the SD card is not full. If the card is full, the
camera will stop taking images.
Check the batteries to make sure that they are new alkaline or
lithium AA batteries. See note above about short battery life.
Make sure that the camera power switch is in the “ON” position
and not in the “OFF”position or in Setup mode.
Make sure that you are using a good quality SD card in your
camera. Tasco recommends SanDisk® SD Cards up to 32GB.
If the SD card has its write protect switch in the lock position, the
camera will not take images.
If you have used an SD card in another device before inserting
it in your trail cam , you might want to try formatting the card
using the “Format” parameter in Setup mode (make sure you
have backed up any important files first, as formatting will erase
all previous files). In some cases, other devices may change the
formatting of the SD card so that it will not work properly with
the trail cam .
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting / FAQ
Camera won’t power up
1.
Make sure that you have installed all 4 batteries in the battery
compartment. Tasco recommends using 4 Energizer® Lithium
AA batteries in this trail cam .
2.
Make sure that the batteries are installed correctly, observing
proper polarity. Always place the negative (flat) end of each
battery in contact with the spring tab side of its slot inside the
camera.
Do not mix old and new batteries.
Do not mix battery types-use ALL lithium or ALL alkaline.
Rechargeable batteries are not recommended.
Still Photo and/or Video Quality Problems
1. Night photos or videos appear too dark
a. Try using a set of new batteries. The flash will stop operating
near the end of the battery life.
b. You will get the best results when the subject is within the
ideal flash range, no farther than 30’ from the camera. Subjects
may appear too dark at greater distances.
c. Please note that when the still photo mode is set to“3P”, or with
very short Delay time settings, some images may appear darker
than others due to the quick response and rapid retriggering
of the camera, allowing less time for the flash to fully recharge
before firing again.
2. Daytime photos or videos appear too dark
a. Make sure that the camera is not aimed at the sun or other
light sources during the day, as this may cause the auto exposure
to produce darker results.
3. Night photos or videos appear too bright
a. You will get the best results when the subject is within the
ideal flash range, no closer than 10’ (3m) from the camera.
Subjects may appear too light at closer distances.
4. Daytime photos or videos appear too bright
a. Make sure that the camera is not aimed at the sun or other
light sources during the day.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting / FAQ
5. Photos with streaked subject
a. In some cases with low lighting conditions and fast moving
subjects, the 3 MP resolution setting (“HI”) may not perform as
well as the 1.3 MP setting (“LO”).
b. If you have multiple images where fast moving subjects
produce streaks on the photo, try the “LO” resolution setting
instead.
6. Red , green or blue color cast
a. Under certain lighting conditions, the sensor can become
confused resulting in poor color images.
b. If this is seen on a consistent basis, then the sensor may need
servicing. Please contact Tasco customer service.
7. Short video clips—not recording to the length set
a. Check to make sure that the SD card is not full.
b. Make sure that the camera has good batteries in it. Near the
end of the battery life, the camera may choose to record shorter
video clips to conserve power.
Photos Do Not Capture Subject of Interest
1.
Try to set your camera up in an area where there is not a heat
source in the camera’s line of sight.
2.
In some cases, setting the camera near water will make the
camera take images with no subject in them. Try aiming the
camera over ground.
3.
4.
Try to avoid setting the camera up on small trees that are prone
to being moved by strong winds.
Remove any limbs which are right in front of the camera lens.
PIR Sensor LED Flashes/Doesn’t Flash
1.
When the camera is in the “Setup” mode, the PIR Indicator LED
on the front of the camera will flash when it senses motion. This
is for setup purposes only and will help the user aim the camera.
During use, the LED will not flash when the camera takes an
image. This is to help keep the camera hidden from game.
2.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting / FAQ
Camera won’t retain settings
1.
Make sure that you have been saving the changes to any parameter
settings that you made while in Setup mode, by pressing “OK”
after changing the setting. If you don’t save your new setting after
changing it, the camera will continue to use the original default
setting for that parameter.
Do not mix old and new batteries.
Do not mix battery types-use ALL lithium or ALL alkaline.
Rechargeable batteries are not recommended.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TWO-YEAR LIMITED WARRANTY
Your Tasco® product is warranted to be free of defects in materials and workmanship for two years after
the date of purchase. In the event of a defect under this warranty, we will, at our option, repair or replace
the product, provided that you return the product postage prepaid. This warranty does not cover damages
caused by misuse, improper handling, installation, or maintenance provided by someone other than a
Tasco Authorized Service Department.
Any return made under this warranty must be accompanied by the items listed below:
1. A check/money order in the amount of $10.00 to cover the cost of postage and handling
2. Name and address for product return
3. An explanation of the defect
4. Proof of Date Purchased
5. Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit,
with return postage prepaid to the address listed below:
IN U.S.A. Send To:
Tasco
IN CANADA Send To:
Tasco
Attn.: Repairs
Attn.: Repairs
9200 Cody
Overland Park, Kansas 66214
25A East Pearce Street, Unit 1
Richmond Hill, Ontario L4B 2M9
For products purchased outside the United States or Canada please contact your local dealer for applicable
warranty information. In Europe you may also contact Tasco at:
Tasco Germany GmbH
European Service Centre
Mathias-Brüggen-Str. 80
D-50827 Köln
GERMANY
Tel: +49 221 995568-0
Fax: +49 221 995568-20
This warranty gives you specific legal rights.
You may have other rights which vary from country to country.
©2013 B.O.P.
Specifications and designs are subject to change without
any notice or obligation on the part of the manufacturer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Compliance Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
The device does not contain any user-serviceable parts. Repairs should
only be made by an Authorized Tasco repair center. Unauthorized repairs or
modifications could result in permanent damage to the equipment, and will
void your warranty and your authority to operate this device under Part 15
regulations.
The shielded interface cable which is provided must be used with the
equipment in order to comply with the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For further questions or additional information please contact:
Tasco
9200 Cody, Overland Park, Kansas 66214
©2013 B.O.P.
Download from Www.Somanuals.com. All Manuals Search And Download.
|