TD-8840 User Guide
External ADSL2+ ROUTER
Rev：1.0.1
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this product
meets the requirements of the following standards:
• EN55022
• EN55024
• EN60950
SAFETY NOTICES
Caution:
Do not use this product near water, for example, in a wet basement or near a swimming pool.
III
Download from Www.Somanuals.com. All Manuals Search And Download.
Package contents
The following contents should be found in your box:
¾
¾
¾
One TD-8840 External ADSL2+ ROUTER
One AC power Adapter for TD-8840 External ADSL2+ ROUTER
One Resource CD for TD-8840 External ADSL2+ ROUTER, including:
•
•
•
This Guide
Other Helpful Information
Quick installation Guide Program
¾
¾
¾
¾
Quick installation Guide
One RJ45 cable
Two RJ11 cable
One ADSL splitter
Note:
)
If any of the listed contents are damaged or missing, please contact the retailer from whom you
purchased the product for assistance.
IV
Download from Www.Somanuals.com. All Manuals Search And Download.
COMMENT
Chapter 1. Introduction ........................................................................................ 1
1.1 Product Overview...................................................................................................... 1
1.2 Main Features ........................................................................................................... 1
1.3 Supporting protocol................................................................................................... 2
1.4 Transmit data-rate..................................................................................................... 2
1.5 ATM propert .............................................................................................................. 3
1.6 System support ......................................................................................................... 3
1.7 Working environment ................................................................................................ 3
1.8 Electric parameter..................................................................................................... 3
1.9 Conventions .............................................................................................................. 4
Chapter 2. Hardware Installation......................................................................... 5
2.1 System requirement.................................................................................................. 5
2.1.1 LED explanation...............................................................................................................5
2.2 Rear-panel ................................................................................................................ 6
2.3 Hardware installation procedures.............................................................................. 6
Chapter 3. System Configuration ........................................................................ 8
3.1 Computer Configuration............................................................................................ 8
3.2 Login ......................................................................................................................... 9
3.3 Web Setup .............................................................................................................. 11
3.4 Software Dial........................................................................................................... 28
Chapter 4. Advantage management setup ....................................................... 30
Appendix A: FAQ.................................................................................................... 31
Appendix B: Default Config................................................................................... 33
Appendix C: Contact Information ......................................................................... 34
V
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Chapter 1.Introduction
1.1 Product Overview
TP-LINK® TD-8840 External ADSL2+ ROUTER is the latest product designed and manufactured
by TP-LINK TECHNOLOGIES CO., LTD. With TP-LINK’s excellent circuit design and high quality
production, we guarantee the ADSL2+ ROUTER’s high performance, great stability and easy to
use.
The TD-8840 uses integrated ADSL2+ transceiver. The AFE supports full-rate ADSL connectivity
conforming to the ITU and ANSI specifications.
In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency ADSL
framing (fast and interleaved) and the I.432 ATM Physical Layer.
The TD-8840 is a complete plug-and-play solution. With standard Ethernet interface, it can be
directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.
The TD-8840 not only uses html (web mode through Ethernet port) to configure the ROUTER but
also uses external utility software. You can download it from our website (http://www.tp-link.com).
1.2 Main Features
¾
High speed and asymmetry data transmit mode, built-in 4-port switch realize multi-user to
share wide-band internet access
¾
¾
¾
¾
¾
Support All ADSL2+ industrial standards
Compatible with all mainstream DSLAM (CO)
Firmware upgradeable
Provide integrated access of internet and route function which face to SOHO user
Advanced DMT modulation and demodulation
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
¾
¾
Real-time Configuration and device monitoring
Quick response semi-conductive surge protect circuit, provides reliable ESD and
surge-protect function
1.3 Supporting protocol
- G.992.1 (G.dmt) - Annex A
- G.992.2 (G.lite) - Annex A
- ANSI T1.413
- G.992.3 (ADSL2) - Annex A and Annex M
- G.992.5 (ADSL2+) Annex A and Annex M
- ADSL dual latency (fast path and interleaved path)
- I.432 ATM physical layer compliant
- Supports RFC2364 (PPPoA)
- Supports RFC2516 (PPPoE)
- Supports RFC2684 (EoA)(Bridged *and Router)
- Supports RFC1577 (IPoA)
Note:
)
“*” Needs the third-party software.
1.4 Transmit data-rate
¾
Max download data-rate: 24Mbps
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
¾
¾
Max upload data-rate: 1Mbps
Max line length: 6Km
1.5 ATM propert
¾
¾
AAL0, AAL5, OAM, RM, and raw cell types supported
Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in
software
¾
Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)
1.6
System support
¾
¾
¾
¾
¾
Support PVC
Support NAT、DHCP and so on
Support IEEE 802.3、IEEE 802.3u
Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
Support Auto-MDIX
1.7
Working environment
¾
¾
¾
Operating temperature: 0 ℃~40 ℃
Storage temperature: -40 ℃~70 ℃
Humidity: 10%~90% (non-condensing)
1.8 Electric parameter
¾
¾
Adaptor power Output: 9VAC/0.8A，50Hz or 60 Hz
Power consumption: 6W Maximum
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
1.9 Conventions
The Router or TD-8840, or device mentioned in this User guide stands for TD-8840 External
ADSL2+ ROUTER without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
You can set the parameters according to your demand.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Chapter 2.Hardware Installation
The TD-8840 maintains five separate interfaces, four Ethernet and one ADSL interface. The
Router should not be located where it will be exposed to moisture or excessive heat. Place the
Router in a location where it can be safely connected to the various devices as well as to a power
source.
2.1 System requirement
Confirm your computer has been installed with networking interface card (NIC) before connecting
ADSL2+ ROUTER to your computer, with operating system supporting the TCP/IP protocol.
2.1.1 LED explanation
The front panel of ADSL2+ ROUTER includes one power indicator (RED) and seven function
indicators (GREEN), as explained in chart below:
Indicator Description
Status
On
Function Details
Power OK
Power fail
PWR
Power
Off
Slow flash
Self-detecting when power up
ADSL
ADSL status
Quick flash Connecting to the telecom network
On
On
Off
On
Connection to telecom network OK
There is mistake when ADSL transmitting data
or receiving data
ALARM
ACT
Mistake
Data
ADSL normal
There is data transmitting or receiving on WAN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
port
Off
On
Off
No data transmitting or receiving on WAN port
1~4(LAN) port normal
Connection on 1~4(LAN) port abnormal
Data transmitting or receiving on 1~4(LAN)
port
LAN(1-4)
Ethernet
Flash
2.2 Rear-panel
¾
¾
ON/OFF: Turn on/off the ADSL2+ ROUTER’s power.
Power (9VAC/0.8A input): please do not use any unknown power adaptor, otherwise your
ADSL2+ ROUTER may be damaged.
¾
RESET(reset default): First press the reset button of ROUTER, then turn on the ROUTER’s
power for at least three seconds. It will resume the default manufacturer’s setup.
1~4(LAN): Connect with your computer’s NIC.
¾
¾
LINE(WAN): Connect to the MODEM Port of Splitter or Connecting the telephone line.
2.3
Hardware installation procedures
The procedure to install the Router can be described in general terms in the following steps:
First Step: Connect the MODEM port of Splitter with the TD-8840 ADSL2+ ROUTER LINE port
by telephone line.
Second Step: Connect category 5 cable with RJ45 jacks to the ADSL2+ ROUTER’s LAN port and
your computer’s NIC.
Third Step: Plug one end of the AC Power Adapter into the Power jack on the Ethernet ADSL2+
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
ROUTER and the other end to a standard electrical outlet.
Last Step: Check the line connection to see if everything is ready. Power up finally.
Figure 2-1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Chapter 3.System Configuration
3.1 Computer Configuration
1. Connect the cable according to Chapter 2, turn on the power.
2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN card in
your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Net mask is
255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).
Figure 3-1
Note:
)
Users of Windows 98 can open TCP/IP Properties according to the following: Right-click (Mouse)
Network Neighbor -> Choose Properties -> Double-click TCP/IP.
Users of Windows 2000/NT/XP can do the following: Right-click Network Neighbor -> Choose
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Properties -> Right-click Local Connection -> Choose Properties -> Double-click Internet
Protocol (TCP/IP).
Note:
)
The words in fact may be different with this guide.
Remarks: you can check whether your configuration is successful through PING command. Enter
Ping 192.168.1.1
If the screen looks like the following, you have been successful.
Figure 3-2
If the screen looks like the following, the connection has failed. Please try again.
Figure 3-3
3.2 Login
Startup Internet Explorer, and enter 192.168.1.1;then enter default user name(admin) 、
password(admin), When ADSL2+ connection is OK, you will see the Figure 3-2.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-4
You will then see the Figure 3-5, you will see some information such as link rate and so on.
Figure 3-5
User name and password is “admin”; if you want to change them, please go to “Management” Æ
“Access control”Æ“Passwords” changing them. (Figure 3-6)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-6
3.3 Web Setup
Choose “Advanced Setup”Æ”WAN”, you will enter the page of Wide Area Network (WAN)
Setup, you will see the Figure 3-7.
Figure 3-7
There are 7 PVC links in the WAN setup page, choose the appropriate PVC according to your
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
need, and then click the edit button, you will enter the page of ATM PVC Configuration (See
Figure 3-8)
Figure 3-8
Enter VPI/VCI value and service category which is provided by your ISP, click next to enter the
next step. You will see the Figure 3-9.
Note:
)
The type of network protocol selected may be different in different areas, there are five types
（Figure 3-9）, So you should ask your ISP to acquire the local type of network protocol and
Encapsulation mode.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-9
After choosing the proper protocol, enter the correct parameters supported by your ISP. Enable
the configurations, then you will go to Internet.
1. PPP over ATM (PPPoA)
If you select the protocol of PPP over ATM (PPPoA), you will see the Figure 3-10, enter the value
of user name and password which is provided by your ISP, after selecting the other function(often
using the default setup), click the next button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-10
You will see the Figure 3-11, then turn on the selected functions according to your demands.
Clicking the next button to enter the next step, you will see the Figure 3-12, finally click save to
complete the configuration.
Figure 3-11
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-12
2. PPP over Ethernet (PPPoE)
If you select the protocol of PPP over Ethernet (PPPoE), you will see the Figure 3-13, enter the
value of user name and password which is provided by your ISP, after selecting the other function
(often using the default setup), click the next button.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-13
You will see the Figure 3-14, then turn on the selected functions according to your needs. Clicking
the next button to enter the next step, you will see the Figure 3-15, finally click save to complete
the configuration.
Figure 3-14
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-15
3. MAC Encapsulation Routing (MER)
If you select the protocol of MAC Encapsulation Routing (MER), you will see the page(Figure
3-16), Enter the parameter and the way which is provided by your ISP, then click the next button.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-16
You will see the Figure 3-17, then turn on the selected functions according to your needs. Clicking
the next button to enter the next step, you will see the Figure 3-18, finally click save to complete
the configuration.
Figure 3-17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-18
4. IP over ATM (IPoA)
If you select the protocol of IP over ATM (IPoA), you will see the Figure 3-19, enter the parameter
and the way which is provided by your ISP, then click the next button.
Figure 3-19
You will see the page (Figure 3-20), then turn on the selected functions according to your needs.
Clicking the next button to enter the next step, you will see the Figure 3-21, finally click save to
complete the configuration.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-20
Figure 3-21
5. Bridging
If you select the Bridging protocol, you just open the bridge service function options, you will see
the Figure 3-22, then click the next button, you will see the Figure 3-23, finally click save to
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
complete the configuration.
Figure 3-22
Figure 3-23
Note:
)
After you complete any setup, the new setup must be saved and the Router must be restarted for
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
the configuration to go into effect. Please click the Save/Reboot button to restart, referring to the
Figure 3-24.
Figure 3-24
Note:
)
All of the above setup is under windows XP OS.
3.3.1 DHCP IP Reservation
When you specify a reserved IP address for a PC on the LAN, that PC will always receive the
same IP address each time when it accesses the DHCP server. Reserved IP addresses should
be assigned to servers that require permanent IP settings.
To setup an Address Reservation entry:
Note:
)
1. DHCP IP Reservation are not available for the connection type of Bridge here, they won’t
display on the screen below since only Bridge is selected.
2. DHCP IP Reservation are not available for the connection type of PPPoE with PPP IP
Extention function selected, and they won’t display on the screen below since PPP IP
Extention is selected.
Choose “Advanced Setup”Æ“LAN”, and you will see the LAN screen, the section allows you to
configure the Router’s LAN ports settings, and you can configure the DHCP IP Reservation
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
function in this screen.
Figure 3-25
1. Click the Set Address Reservation botton, and the Address Reservation screen pop up,
as it showed below ;
Figure 3-26
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
2. Click New Entry botton to add new entries, and the screen showed below pop up, you can
modify an address reservation entry in this screen;
Figure 3-27
3. Type the MAC Address(00:13:8F:A9:E6:CA for instance) of the computer which you want to
reserve an IP(192.168.1.100 for instance) for in the MAC Address text box;
4. Type the IP Address(192.168.1.100 for instance) you have reserved in the Reserved IP
Address text box;
5. Click save botton to save the settings you have set;
Note:
)
The MAC Address and IP Address added in the text box used for illustrating. That may be
differences with your circs.
6. When you have saved the settings, the new entry will added to the Address Reservation
screen showed below.
Figure 3-28
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
7. Click Save/Reboot button to save the settings and reboot the router.
Note:
)
The function won't take effect until the router reboots.
3.3.2 DNS
When you select the connection type PPPoE, PPPoA, MER or IPoA for WAN configuration, you
will see the DNS menu in the Web-based Utility (shown in Figure 3-29). It includes DNS Server
and Dynamic DNS submenus.
Figure 3-29
3.3.2.1. DNS Server
Choose “Advanced Setup”Æ“DNS”Æ“DNS Server”. You can see the DNS Server screen, this
screen allows you to configure the DNS Server Addresses (shown in Figure 3-30).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-30
If you select Enable Automatic Assigned DNS, this Router will accept automatically the first
received DNS assignment from one of PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the
connection establishment. If the checkbox is not selected, please enter the primary and /or
optional secondary DNS server IP addresses provided by your ISP. Then click the Save button to
save the new configuration.
Note:
)
You have to reboot the Router to make the new configuration take effect.
3.3.2.2. Dynamic DNS
Choose “Advanced Setup”Æ“DNS”Æ“Dynamic DNS”, you can see the Dynamic DNS screen,
this screen allows you to configure the Dynamic DNS (shown in Figure 3-31).
The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a
fixed host and domain name to a dynamic Internet IP Address. The Dynamic DNS service allows
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
you to alias a dynamic IP address to a static hostname in any of the many domains, allowing your
Router to be more easily accessed from various locations on the Internet.
Figure 3-31
To setup DDNS, follow these instructions:
1. Click the Add button (pop-up Figure 3-31), then you will set the DDNS in the next screen
(shown in Figure 3-32).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Figure 3-32
Note:
)
This page allows you to add a Dynamic DNS address from DynDNS.org,TZO or No-IP.
2. Select D-DNS provider(DynDNS.org,TZO or No-IP) in the drop-down list.
3. Enter the Hostname of the DNS Server, and select the corresponding Interface for the
DDNS, you can leave it default.
4. Type the User Name and Password for your DDNS account.
5. Click the Save/Apply button to save the entry.
3.4 Software Dial
If TD-8840 CPE work in bridged (RFC 1483 Bridged) mode when it connecting Internet. You must
install dial software on your PC. There are some software working on WINDOWS in market,
example for EnterNet3000、RASPPPoE、WinPeET.
How do I set up the connection in the windows XP?
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
1. The users of Windows XP can click the “start->All Programs->Accessories->
Communications->New connection wizard”, then click Next to enter the configuration
page.
2. Please you select the “connect to the internet” ,and then click the Next button to enter the
next page and select the “set up my connection manually”, click Next to enter the next
page.
3. Please select the “connect using a broadband connection that requires user name and
password”, click Next to type the name of your ISP in the current page, and then click
Next.
4. Enter an ISP account name and password, if you have forgotten an existing account
name or password, please connect with your ISP, click Next.
5. To create the connection and close this wizard, click finish to add a shortcut to this
connection to your desktop.
6. When you assess the internet by ADSL, double-click this shortcut of dial connection in your
desktop, enter the account name and password, then click connect to connect the internet.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Chapter 4. Advantage management setup
In order to satisfy our customer's needs we offer an excellent Web management interface. Feel
free to utilize the Advantage application and online software upgrades. The functions of the Web
management interface are as follows:
1. Upgrade software
2. Modify the default IP address of the port of LAN(192.168.1.1)
3. Modify the login password
4. Configure DHCP
5. Check the information of IP and the operation status
6. Configure the NAT function
7. Configure the DNS parameters
8. Configure Security rule
9. Configure DSL parameter
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Appendix A: FAQ
1. What related parameters are required to acquire ISP when you want to access the
internet by ADSL2+ Router?
1) Dial user: Connection protocol, User name, Password, Value of VPI/VCI, Encapsulation
mode of AAL5 and so on.
2) Static IP user: Connection protocol, WAN IP Address, Subnet Mask, Gateway, Value of
VPI/VCI, Encapsulation mode of AAL5 and so on.
2. About Connection protocol, VCI/VPI, Encapsulation mode of AAL5
1) This product supports the PPP protocol over ATM (PPPoA)、PPP over Ethernet
(PPPoE)、MAC Encapsulation Routing (MER)、IP over ATM (IPoA) and Bridging. You
may be used with any one of the five protocols above. Because the ISP in different areas
supports different protocol, you must choose the protocol which is supported by your
ISP.
2) The VPI is the English abbreviation of the Virtual Path Identifier, the VCI is the English
abbreviation of the Virtual Channel Identifier, the value of VCI/VPI must be compatible
with the value that provided by ISP.
3) Encapsulation mode of AAL5 include: LLC/SNAP and VC_MAX(often using LLC/SNAP).
3. Why the LAN’s and the NIC’s LED both bright, but the configuration interface is
inaccessible?
1) Use the order of ping 192.168.1.1 to check the Accuracy of connection.
2) Check the Accuracy of working NIC.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
3) Whatever the setup of the IP address on your computer (if you close the DHCP function,
you can't obtain the IP address automatically, must specify the IP address of your
computer manually).
4) Run the winipcfg order in the windows 95/98(run the ipconfig order in the windows 2000)
to check whether setup the IP address, subnet mask, default gateway by DHCP.
5) Resume the ADSL Modem default configuration if necessary.
4. Have complete all configurations, but can’t dial through computer
1) Check the indicator of ADSL, it should be working in normally.
2) Check the accuracy of parameter of value of VPI/VCI, Encapsulation mode of AAL5 and
so on, whether you need to install the dial software, such as Winpoet, Enternet.
3) This product has the PPP dial procedure inside, so you will not need to use the dial
software if your protocol is PPPoA or PPPoE, ADSL Modem will connect automatically.
4) You can check whether your ADSL Modem succeeds in connection with PING
command.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Appendix B: Default Config
admin
admin
User name
Password
IP Address
192.168.1.1
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8840
External ADSL2+ Router User Guide
Appendix C: Contact Information
For help with the installation or operation of TP-LINK Product, please visit our website.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
|