Tanaka Trimmer THT 210 THT 210s THT 2000 THT 2100 THT 2120 THT 2510 THT 2520 THT 240 THT 2530 THT 2540 HTD 2520PF HTD 2522PF HTD 2526PF HTD 2530PF HTS 2530PF User Manual

Owner’s Manual  
Model Numbers:  
P/N 28334  
Date04-06-05  
THT-210/210S/2000/2100/2120  
THT-2510/2520/240/2530/2540  
HTD-2520PF/2522PF/2526PF  
HTD-2530PF,HTS-2530PF  
HEDGETRIMMERS  
THT-2120  
HTD-2530PF  
SupplierToTheOutdoorPowerEquipmentIndustry  
th  
ISM, Inc. 10284 StreetSWAuburn, WA98001Phone:(253)333-1200Fax:(253)333-1212  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
1. Recoil Starter  
2. Fuel Tank  
3. Safety Trigger  
4. Throttle Trigger  
5. Front Handle  
6. Rear Handle  
7. Spark Plug  
8. Hand Guard  
9. Cutting Blade  
10. Air Cleaner  
11. Ignition Switch  
12. Blunt Guard (optional)  
13. Gear Case  
14. Choke Lever  
15. Lock Button  
16. Blade Cover  
17. Lock Button  
18. Priming Pump  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
2. Warnings and safety instructions.  
Cutting Safety  
Do not cut any material other than plant hedge.  
Operator Safety  
Inspect the area to be cut before each use. Remove objects  
which can be thrown or become entangled.  
Keep others including children, animals, bystanders and  
helpers outside the 15 m (50ft) hazard zone. Stop the  
engine immediately if you are approached.  
Always wear a safety face shield or goggles.  
Always wear heavy, long pants, boots and gloves. Do not  
wear loose clothing, jewelry, short pants, sandals or go  
barefoot. Secure hair so it is above shoulder length.  
Do not operate tool when you are tired, ill or under the  
influence of alcohol, drugs or medication.  
Never let a child or inexperienced person operate the  
machine.  
Hold the tool firmly with both hands.  
Keep firm footing and balance. Do not over-reach.  
Keep all parts of your body away from the muffler and  
cutting attachment when the engine is running.  
Keep the cutting tool below shoulder level. NEVER operate  
unit from a ladder, while in a tree or from any unstable  
support.  
Wear hearing protection.  
Never start or run the engine inside a closed room or  
building. Breathing exhaust fumes can kill.  
Keep handles free of oil and fuel.  
Keep hands away from cutting equipment.  
Do not grab or hold the unit by the cutting equipment.  
When the unit is turned off, make sure the engine has  
stopped before the unit is set down.  
Maintenance Safety  
Maintain the tool according to recommended procedures.  
Disconnect the spark plug before performing maintenance  
except for carburetor adjustments.  
Keep others away when making carburetor adjustments.  
Use only genuine replacement parts as recommended by the  
manufacturer.  
When operation is prolonged, take a break from time to time  
so that you may avoid possible white finger disease, which is  
caused by vibration.  
Tool Safety  
Transport and storage  
Inspect the entire tool before each use. Replace damaged  
parts. Check for fuel leaks and make sure all fasteners are in  
place and securely fastened.  
Carry the tool by hand with the engine stopped and the  
muffler away from your body.  
Allow the engine to cool, empty the fuel tank, and secure the  
tool before storing or transporting in a vehicle.  
Empty the fuel tank before storing the tool. It is  
recommended that the fuel be emptied after each use.  
If fuel is left in the tank, store so fuel will not leak.  
Store tool out of the reach of children.  
Clean the unit carefully and store it in a dry place.  
Make sure engine switch is off when transporting or storing.  
When transporting in a vehicle, cover blade with blade cover.  
Replace parts that are cracked, chipped or damaged in any  
way before using the tool.  
Make sure the safety guard is properly attached.  
Keep others away when making carburetor adjustments.  
Use only accessories as recommended for this tools by the  
manufacturer.  
WARNING!  
Never modify the tool in any way. Do not use the tool for any job  
except that for which it is intended.  
If situations occur which are not covered in this manual, take care and  
use good judgment. Contact your dealer if you need assistance.  
Fuel Safety  
Mix and pour fuel outdoors and where there are no sparks or  
flames.  
Pay special attention to statements preceded by the following words:  
Use a container approved for fuel.  
Do not smoke or allow smoking near fuel or the tool or while  
using the tool.  
WARNING!  
Indicates a strong possibility of severe personal injury or loss of life, if  
instructions are not followed.  
Wipe up all fuel spills before starting engine.  
Move at least 3 m (10 ft) away from fueling site before  
starting engine.  
Stop engine before removing fuel cap.  
Empty the fuel tank before storing the tool. It is  
recommended that the fuel be emptied after each use. If  
fuel is left in the tank, store so fuel will not leak.  
Store tool and fuel in area where fuel vapors cannot reach  
sparks or open flames from water heaters, electric motors or  
switches, furnaces, etc.  
CAUTION!  
Indicates a possibility of personal injury or equipment damage, if  
instructions are not followed.  
NOTE!  
Helpful information for correct function and use.  
WARNING!  
Anti-vibration systems do not guarantee that you will not sustain white  
finger disease or carpal tunnel syndrome. Therefore, continual and  
regular users should monitor closely the condition of their hands and  
fingers. If any of the above symptoms appear, seek medical advice  
immediately.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
3. Assembly procedures  
Handle B (3) and Gathering Plate (4) (Fig, 1-1)  
1. Remove the four washers and nuts (1) from cutting blade end.  
NOTE! In case of Handle B installation only, remove only the nut on the longest bolt.  
2. Set the gathering plate on the guide bar, then finger tighten the three washers and nuts. *Use one each (5)  
of the two washers, which have been provided, under the gathering plate or on the two blade-fixing bolts  
from the cutting-blade end to install the gathering plate on THT-2540. (If so equipped)  
3. Set the handle B on the longest bolt and finger tighten with the washer and nut.  
4. Before securing the finger-tighten nuts, screw the blade fixing bolts (2) to be seated, then loosen the bolts  
approx. 1/2 turn.  
5. With the bolts set at that position tighten the blade fixing nuts.  
Handle B (3) and Blunt guard (6) for USA/CANADA (Fig. 1-2,3)  
1. Remove the four nuts (1) (in case of double sided blade, three nuts (1)) from power head side.  
NOTE! (For THT-2520,HTD-2530PF)  
To set the blunt guard on the unit, loosen the blade fixing bolts so that the blunt guard can be slid into place. Do not  
use the washer originally used under support plate (8) together with blunt guard.  
2. Set the blunt guard on the guide bar, then finger tighten the three nuts.  
3. Set the handle B (3) on the longest bolt (Single sided blade) and finger tighten with the washer and nut.  
4. Before securing the finger-tighten nuts, screw the blade fixing bolts (2) to be seated, then loosen the bolts approx.  
1/2 turn.  
5. With the bolts set at that position tighten the blade fixing nuts.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
4. Operating procedures  
Fuel (Fig. 2-1)  
WARNING!  
The hedge trimmer is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil.  
Provide good ventilation, when fueling or handling fuel.  
Fuel  
• Always use branded 89 octane unleaded gasoline.  
• Use Tanaka two-cycle oil or a quality two-cycle oil at mixing ratio of 50:1 (Gasoline (A) : Oil (B)).  
• Never use multi-grade oil (10 W/30) or waste oil.  
• Always mix fuel and oil in a separate clean container.  
Always start by filling half the amount of fuel, which is to be used. Then add the whole amount of oil. Mix (shake) the  
fuel mixture.  
Add the remaining amount of fuel.  
Mix (shake) the fuel-mix thoroughly before filling the fuel tank.  
Fueling  
WARNING!  
Always shut off the engine before refueling.  
Slowly open the fuel tank (1), when filling up with fuel, so that possible over-pressure disappears.  
Tighten the fuel cap carefully, after fueling.  
Always move the trimmer at least 3 m (10 ft.) from the fueling area before starting.  
Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank.  
Make sure that the fuel is well mixed by shaking the container, before fueling.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
Starting (Fig. 2-2, 2B)  
CAUTION!  
Before starting, make sure the cutting attachment does not touch anything.  
1. Set ignition switch (1) to the ON position. (Fig. 2-2)  
*Push priming bulb (4) several times so that fuel flows through the bulb or return pipe. (if so equipped)(Fig. 2-2C)  
2. With the safety lever (2) pressed (if so equipped), pull throttle trigger and push lock button (3) (if so equipped),  
then slowly release the throttle trigger first, then the safety lever. This will lock the throttle in the starting position.  
3. Set choke lever to CLOSED position (4). (Fig. 2-3)  
4. Pull recoil starter briskly, taking care to keep the handle in your grasp and not allowing it to snap back. (Fig.2-4,4B)  
5. When you hear the engine want to start, return choke lever to RUN position (open). Then pull recoil starter briskly  
again.  
NOTE!  
If engine does not start, repeat procedures from 2 to 5.  
6. After starting engine, pull throttle trigger to release throttle lock. Then allow the engine about 2-3 minutes to warm  
up before subjecting it to any load.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
Cutting  
When cutting, operate engine at full throttle as this maintains proper cutter speed.  
When trimming top of hedge, hold trimmer so blades are between 15 and 30 degrees from a horizontal position and  
swing trimmer in an arc toward edge of hedge to sweep cuttings off.  
When trimming sides of hedge, hold blade vertically and swing unit in an arc.  
NOTE! (THT-210/2120/2520, HTD-2526PF/2530PF) (Fig. 2-5)  
In case your trimmer is twist handle type (1), please note that the cutting angle can be adjusted by loosening handle  
locking nut (2). After adjustment has been made, be sure to retighten the nut.  
NOTE! (THT-210S) (Fig. 2-5B)  
The rear handle can be set in five different positions by pushing the lock button (3) and turning the rear handle. It is  
extremely important that the handle is locked in the selected position. The lock button can not push while the throttle  
trigger is pulling.  
NOTE: The throttle trigger will not work if the rear handle is unlocked.  
Stopping (FIG. 2-6,6B)  
Decrease engine speed, and push ignition switch to stop position.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
5. Maintenance  
MAINTENANCE, REPLACEMENT, OR REPAIR OF THE  
EMISSION CONTROL DEVICES AND SYSTEMS MAY  
BE PERFORMED BY ANY NONROAD ENGINE REPAIR  
ESTABLISHMENT OR INDIVIDUAL.  
Carburetor adjustment (Fig. 3-1, 1B)  
WARNING!  
The blades may be moving during carburetor adjustments.  
WARNING!  
Never start the engine without the complete clutch cover! Otherwise the clutch can come loose and cause personal injuries.  
In the carburetor, fuel is mixed with air. When the engine is test run at the factory, the carburetor is basically adjusted. A  
further adjustment may be required, according to climate and altitude. The carburetor has one adjustment possibility:  
T = Idle speed adjustment screw.  
Idle speed adjustment (T)  
Check that the air filter is clean. When the idle speed is correct, the cutting attachment will not rotate. If adjustment is  
required, close (clockwise) the T-screw, with the engine running, until the cutting attachment starts to rotate.  
Open (counter-clockwise) the screw until the cutting attachment stops. You have reached the correct idle speed when the  
engine runs smoothly in all positions well below the rpm when the cutting attachment starts to rotate.  
If the cutting attachment still rotates after idle speed adjustment, contact your service workshop.  
Air filter (Fig. 3-2, 2B)  
The air filter must be cleaned from dust and dirt in order to avoid:  
• Carburetor malfunctions.  
• Starting problems.  
• Engine power reduction.  
• Unnecessary wear on the engine parts.  
• Abnormal fuel consumption.  
Clean the air filter daily or more often if working in exceptionally dusty areas.  
Cleaning the air filter  
Remove the air filter cover and the filter (1).  
Rinse it in warm soap suds. Check that the filter is dry before reassembly. An air filter that has been used for some time  
cannot be cleaned completely. Therefore, it must regularly be replaced with a new one. A damaged filter must always be  
replaced.  
NOTE!  
Saturate the element in 2-cycle oil or the equivalent. Squeeze the element to distribute the oil completely and to remove any  
excess oil.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
Spark plug (Fig. 3-3)  
The spark plug condition is influenced by:  
• An incorrect carburetor setting.  
• Wrong fuel mixture (too much oil in the gasoline)  
• A dirty air filter.  
• Hard running conditions (such as cold weather).  
These factors cause deposits on the spark plug electrodes, which may result  
in malfunction and starting difficulties. If the engine is low on power, difficult  
to start or runs poorly at idling speed, always check the spark plug first. If  
the spark plug is dirty, clean it and check the electrode gap. Readjust if  
necessary. The correct gap is 0.6 mm (.024'). The spark plug should be  
replaced after about 100 operation hours or earlier if the electrodes are  
badly eroded.  
NOTE!  
In some areas, local law requires using a resistor spark plug to suppress ignition signals. If this machine was originally  
equipped with resistor spark plug, use same type of spark plug for replacement.  
Cutter blade (Fig. 3-4, 4B)  
The blades are installed to the cutter guide with the four or  
five bolts. Those bolts are tightened with a clearance so that  
the cutters can move smoothly.  
When clearance is too small:  
The cutters do not move properly and the sliding surfaces  
may seize.  
When clearance is too large:  
The cutters are poor in sharpness.  
To adjust the cutter clearance:  
1. Loosen the cutter fixing nuts.  
2. Fully tighten the cutter fixing bolts and then loosen them approx. 1/2 turn.  
3. With the bolts set at that position, tighten the cutter fixing nuts.  
Be sure to replace cutter guide fixing bolts when they are loosened, worn or damaged. Also be sure to replace damaged  
cutter blade.  
NOTE!  
Properly lubricate the cutter sliding surfaces with machine oil.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
Gear case (Fig. 3-5, 5B)  
Apply a good quality lithium based grease through the grease fitting until a small amount comes out between the  
cutter blades and the gear case.  
NOTE!  
Lubrication should be applied at 50 hour intervals and more frequent at heavy use.  
Fuel filter (Fig. 3-6)  
Remove the fuel filter from the fuel tank and thoroughly wash it in solvent. After that, push the filter into the tank  
completely.  
NOTE!  
If the filter is hard due to dust and dirt, replace it.  
Cleaning the cylinder fins (Fig. 3-7)  
When wood chips are caught between cylinder fins (1),  
the engine may overheat, resulting in lower output. To  
avoid this, always keep cylinder fins and fan case clean.  
Every 100 Operating hours, or once a year (more often if  
conditions require), clean fins and external surfaces of  
engine of dust, dirt and oil deposits which can contribute  
to improper cooling.  
Cleaning the muffler (Fig. 3-8)  
Remove the muffler and spark arrestor (if so  
equipped), and clean out any excess carbon  
from the exhaust port or muffler inlet every 100  
hours of operation.  
For long-term storage  
Drain all fuel from the fuel tank. Start and let engine run until it stops. Repair any damage which has resulted from use. Clean  
the unit with a clean rag, or the use of high pressure air hose. Put a few drops of two-cycle engine oil into the cylinder  
through the spark plug hole, and spin the engine over several times to distribute oil. Cover the unit and store it in a dry area.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
Maintenance schedule  
Below you will find some general maintenance instructions.  
For further information please contact your service dealer.  
Daily maintenance  
Clean the exterior of the unit.  
Check the blade guard for damage or cracks. Change the guard in case of impacts or cracks.  
Check that the blade is sharp, and without cracks.  
Check that the blade nut is sufficiently tightened.  
Make sure the blade transport guard is undamaged and that it can be securely fitted.  
Check that nuts and screws are sufficiently tightened.  
Weekly maintenance  
Check the starter, especially cord and return spring.  
Clean the exterior of the spark plug.  
Remove it and check the electrode gap. Adjust it to 0.6 mm, or change the spark plug.  
Clean the cooling fins on the cylinder and make sure the air intake at the starter is not clogged.  
Check that the angle gear is filled with grease.  
Clean the air filter.  
Monthly maintenance  
Rinse the fuel tank with gasoline.  
Clean the exterior of the carburetor and the space around it.  
Clean the fan and the space around it.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
6. Specifications  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
6. Specifications cont.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THT-210/210S/2000/2100/2120/2520, THT-240/2510/2530/2540/262  
HTD-2520PF/2522PF/2526PF/2530PF, HTS-2530PF  
Owner’s Manual  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Copier AL 1451 User Manual
Shindaiwa Trimmer 63848 94010 User Manual
Shure Microphone 444d User Manual
Shure Microphone PGA27 User Manual
Sony Car Stereo System XR CA305 User Manual
Sony GPS Receiver NVX P1 User Manual
Sony Home Theater System BDV E770W User Manual
Standard Horizon Marine Radio GX2360S User Manual
Sungale Tablet ID430WTA User Manual
SVAT Electronics Home Security System qxd600 User Manual