Symphonic TV DVD Combo SC720FDF User Manual

20 inch DVD TRIPLE COMBO  
Owner’s Manual  
SC720FDF  
FEATURES  
• Auto Channel Programming  
• Timer Recording  
1 year 8 events programmable  
Daily/Weekly recording  
• One Touch Recording  
• Auto Clock Setting  
• Screen Saver  
• Auto Power On and Off  
• Parental Lock  
• Resume Play (DVD)  
• Closed Caption Decoder  
• Virtual Surround  
SUPPLIED ACCESSORIES  
This unit comes with the following accessories. Please confirm that  
all the accessories are included.  
Owner's Manual  
P Remote Control  
P AA batteries x 2  
P Owner's Manual  
(NF101UD)  
(1EMN21534)  
INSTRUCCIONES EN ESPAÑOL INCLUDAS  
PLEASE READ BEFORE USING THIS EQUIPMENT  
IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING  
AFTER READING OWNER’S MANUAL,  
PLEASE CALL TOLL FREE 1-800-242-7158 OR VISIT OUR WEB SITE AT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14. Lightning - For added protection for this unit receiver during  
a lightning storm, or when it is left unattended and unused  
for long periods of time, unplug it from the wall outlet and  
disconnect the antenna or cable system. This will prevent  
damage to the unit due to lightning and power-line surges.  
15. Power Lines - An outside antenna system should not be  
located in the vicinity of overhead power lines or other elec-  
tric light or power circuits, or where it can fall into such power  
lines or circuits. When installing an outside antenna system,  
extreme care should be taken to keep from touching such  
power lines or circuits as contact with them might be fatal.  
16. Overloading - Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17. Object and Liquid Entry - Never push objects of any kind  
into this unit through openings as they may touch dangerous  
voltage points or short out parts that could result in a fire or  
electric shock. Never spill liquid of any kind on the unit.  
18. Servicing - Do not attempt to service this unit yourself as  
opening or removing covers may expose you to dangerous  
voltage or other hazards. Refer all servicing to qualified ser-  
vice personnel.  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the unit.  
c. If the unit has been exposed to rain or water.  
d. If the unit does not operate normally by following the operat-  
ing instructions. Adjust only those controls that are covered  
by the operating instructions, as improper adjustment of  
other controls may result in damage and will often require  
extensive work by a qualified technician to restore the unit to  
its normal operation.  
e. If the unit has been dropped or damaged in any way.  
f. When the unit exhibits a distinct change in performance, this  
indicates a need for service.  
20. Replacement Parts - When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
21. Safety Check - Upon completion of any service or repairs to  
this unit, ask the service technician to perform routine safety  
checks to determine that the unit is in proper operating con-  
dition.  
22. Heat - This unit product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
19. Damage Requiring Service - Unplug this unit from the wall  
outlet and refer servicing to qualified service personnel  
under the following conditions:  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.  
This product incorporates copyright protection technology that is protected by U.S. patents and other intellec-  
tual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is  
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse  
engineering or disassembly is prohibited.  
RADIO-TV INTERFERENCE  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-  
ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-  
nications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-  
ment does cause harmful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment and receiver.  
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
4) Consult the dealer or an experienced radio/TV technician for help.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to  
this equipment may cause harmful interference unless the modifications are expressly approved in the  
owner’s manual. The user could lose the authority to operate this equipment if an unauthorized change or  
modification is made.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
LASER SAFETY  
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service  
this device, due to possible eye injury.  
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.  
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.  
DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK MECHANISM.  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER  
JUSQU'AU FOND.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guide-  
lines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system  
of the building as close to the point of cable entry as practical.  
LOCATION  
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place  
for its installation:  
• Shield it from direct sunlight and keep it away from sources of intense heat.  
• Avoid dusty or humid places.  
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the  
top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.  
• Install unit in a horizontal position.  
• Avoid locations subject to strong vibration.  
• Do not place the unit near strong magnetic fields.  
• Avoid moving unit to locations where temperature differences are extreme.  
• Be sure to remove disc and unplug the AC power cord from the outlet before carrying the unit.  
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE  
• Do not handle the power cord with wet hands.  
• Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.  
• If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
• Do not put your fingers or objects into the unit disc loading tray.  
• Do not place anything directly on top of the unit.  
MOISTURE WARNING  
• Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or  
after heating a cold room or under conditions of high humidity. If you play a videotape or DVD in a moist  
unit, it may damage the tape or DVD and the unit. When the condensation occurs inside the unit, turn the  
unit on and leave it at least 2 hours to dry out.  
NOTE ABOUT RECYCLING  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
Manufactured under license from Dolby Laboratories.  
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.  
The serial number of this product may be found on the back of the unit. No other unit has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a  
permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ABLE OF CONTENTS  
T
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .2  
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . .2  
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . .5  
SYMBOLS USED IN THIS MANUAL . . . . . . . . . . . .5  
PREPARATION FOR USE . . . . . . . . . . . . . . . . . .6  
ANTENNA/CABLE CONNECTIONS . . . . . . . . . . . .6  
CONNECTING TO AN EXTERNAL DEVICE (FRONT) . .6  
CONNECTING TO A DIGITAL AUDIO DEVICE (REAR) .7  
INSTALLING THE BATTERIES IN REMOTE CONTROL .7  
OPERATING CONTROLS AND FUNCTIONS . . .8  
DVD SECTION  
ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . .22  
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . .22  
UNPLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . .22  
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . .23  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . .23  
DISC MENU / TITLE MENU . . . . . . . . . . . . . . . . . .23  
SPECIAL PLAYBACK FUNCTIONS & SETTINGS . . .24  
FUNCTION TABLE . . . . . . . . . . . . . . . . . . . . . . . .24  
AUDIO MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .25  
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . .25  
ANGLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .25  
ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25  
BLACK LEVEL MENU . . . . . . . . . . . . . . . . . . . . . .26  
V.S.S(Virtual Surround System) . . . . . . . . . . . . . . .26  
SEARCH MENU . . . . . . . . . . . . . . . . . . . . . . . . . .26  
REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . .27  
PROGRAMMED PLAYBACK . . . . . . . . . . . . . . . . .28  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . .28  
ON-SCREEN INFORMATION . . . . . . . . . . . . . .28  
CHANGING THE DVD SET UP ITEMS . . . . . . .29  
CUSTOM MENU . . . . . . . . . . . . . . . . . . . . . . . . . .29  
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31  
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . .32  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . .34  
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . .35  
CABLE CHANNEL DESIGNATIONS . . . . . . . . . . .35  
LANGUAGE CODE LIST . . . . . . . . . . . . . . . . . . . .35  
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . .36  
TV/VCR SECTION  
TV OPERATION AND SETTINGS . . . . . . . . . . . .9  
WATCHING A TV PROGRAM . . . . . . . . . . . . . . . . .9  
SLEEP TIMER / PICTURE CONTROL . . . . . . . . . . .9  
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . .10  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . . . . . . .11  
ON-SCREEN MENU LANGUAGE . . . . . . . . . . . . .11  
CLOSED CAPTION SYSTEM . . . . . . . . . . . . . . . .11  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . . . .12  
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . . . . .13  
ON-SCREEN DISPLAY . . . . . . . . . . . . . . . . . . .14  
STATUS DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . .14  
CHECKING THE STATUS . . . . . . . . . . . . . . . . . . .14  
MTS (Multi-channel Television Sound) SYSTEM . .14  
VIDEO CASSETTE . . . . . . . . . . . . . . . . . . . . . .15  
PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . .15  
SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . . . .16  
RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . .16  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . .16  
SEARCH FUNCTION . . . . . . . . . . . . . . . . . . . .16  
ZERO RETURN . . . . . . . . . . . . . . . . . . . . . . . . . . .16  
PICTURE SEARCH . . . . . . . . . . . . . . . . . . . . . . . .17  
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
INDEX SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . .17  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . .18  
OTR (One Touch Recording) . . . . . . . . . . . . . . . . .18  
AUTOMATIC TIMER RECORDING . . . . . . . . . . . .19  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . . . . . .21  
COPYING A VIDEO CASSETTE (from another source) .21  
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . .37  
WARRANTY . . . . . . . . . . . . . . . . . .BACK COVER  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some headings and notes in this manual, with the following meanings.  
Description refers to TV/VCR  
operation (in the TV/VCR mode).  
Description refers to playback of  
audio CDs (in the DVD mode).  
TV/VCR  
Description refers to playback of  
DVD video discs (in the DVD mode).  
Description refers to the items  
to be set by the QUICK mode  
(in the DVD mode).  
QUICK  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
REPARATION FOR USE  
P
ANTENNA/CABLE CONNECTIONS  
Plug the incoming cable into the ANT. jack on the rear of the unit.  
If your cable service supplies you with a converter box or if you use a satellite system, connect the box with  
this unit as shown below.  
Cable  
TV signal  
Antenna  
or  
Rear of the unit  
ANT.  
A
U
D
I
O
O
U
T
COAXIAL  
Incoming cable from home  
Antenna / Cable Company  
(No Cable Box)  
ANT.  
Cable Box or Satellite Box*  
*NOTE  
OUT  
OR  
IN  
(DO NOT DISCONNECT FROM BOX)  
Some cable TV systems use scrambled  
signals and require a special converter to  
receive these channels. Consult your local  
cable company.  
Incoming cable from Cable Company  
or Satellite Antenna  
NOTE:  
Bent pin  
For your safety and to  
avoid damages to the unit,  
unplug the antenna cable  
from the ANT. jack before  
moving the unit.  
Before plugging the antenna into  
the ANT. jack of the unit, check  
that the pin is not bent. If it is bent,  
straighten the pin as illustrated,  
then plug the pin into the ANT. jack  
of the unit.  
Cable  
Plug  
(Needs to be  
straightened)  
(Straight pin)  
CONNECTING TO AN EXTERNAL DEVICE (FRONT)  
When you watch a program recorded on another source (VCR or video camera), use the  
AUDIO/VIDEO input jacks on the front of the unit.  
AUX  
Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO  
jacks of this unit.  
Then use [SELECT] or [CH. K / L] until "AUX" appears on the screen.  
OPEN/  
CLOSE  
STOP/  
EJECT  
POWER  
PLAY  
SELECT  
PLAY  
VOLUME  
SKIP  
SKIP  
STOP  
CHANNEL  
REC/OTR  
REW  
F.FWD  
HEADPHONE  
VIDEO  
L
-
AUDIO  
-
R
E
SEARCH  
D
DVD  
TV/VCR  
ex.  
VCR or video  
camera, etc.  
To the Audio output jacks  
Audio Cable (commercially available)  
(IN)  
(OUT)  
(OUT)  
HEADPHONE  
VIDEO  
L
AUDIO  
R
Front of the unit  
To the Video output jack  
(IN)  
Video Cable (commercially available)  
NOTE:  
When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the monaural VCR  
(another source) to the AUDIO L jack of this unit. The audio will output in both L and R channel equally.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
CONNECTING TO A DIGITAL AUDIO DEVICE (REAR)  
You can connect this unit to a digital audio device to enjoy the digital audio of DVD. Connect to an amplifier  
equipped with digital input jacks, such as MD deck or DAT deck. To play a DVD disc in a Dolby Digital Multi-  
channel surround format in this unit, connect to a Dolby Digital decoder.  
Use an audio coaxial digital cable (commercially available) for the audio connections.  
AUDIO OUT  
COAXIAL  
AUDIO OUT  
COAXIAL  
To AUDIO OUT  
(OUT)  
COAXIAL jack  
(DVD AUDIO OUT Only )  
Dolby Digital  
decoder  
To Coaxial digital  
Audio input jack  
(IN)  
or  
Audio coaxial digital cable  
(commercially available)  
MD deck,  
DAT deck, etc.  
To Coaxial digital  
Audio input jack  
(IN)  
NOTES:  
• The audio source on a disc in a Dolby Digital Multi-channel surround format cannot be recorded as digital sound by an  
MD or DAT deck.  
• Be sure to turn off the power to all devices in the system before connecting another device.  
• Refer to the Owner's Manuals for the devices to be connected to the unit.  
To connect to a MD or DAT deck, set "DOLBY DIGITAL" to "PCM" for the audio output in the setup mode, and to con-  
nect to a Dolby Digital decoder, set to "BITSTREAM" (Refer to "AUDIO SETTING" on page 30). Playing a unit using  
incorrect settings may generate noise distortion and may also damage the speakers.  
INSTALLING THE BATTERIES IN REMOTE CONTROL  
1) Open the battery compartment cover by pressing  
[BATTERY PRECAUTIONS]  
the cover on the remote unit in the direction of  
the arrow.  
2) Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
Be sure to follow the correct polarity as indicat-  
ed in the battery compartment. Reversed batter-  
ies may cause damage to the device.  
Do not mix different types of batteries together  
(e.g. Alkaline and Carbon-Zinc) or old batteries  
with fresh ones.  
3) Replace the cover.  
If the device is not to be used for a long period  
of time, remove the batteries to prevent damage  
or injury from possible battery leakage.  
1
2
3
Do not try to recharge batteries not intended to  
be recharged; they can overheat and rupture.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PERATING CONTROLS AND FUNCTIONS  
O
- FRONT PANEL -  
DVD butttons  
TV/VCR bbuttons  
SEARCH  
DVD  
TV/VCR  
1
2
3
4
3
5
6
7
8 9 10 11 1213 14  
4
15 16 17 18 19 20 21  
17 Remote sensor window  
18 HEADPHONE Jack  
- REMOTE CONTROL -  
19 VIDEO input Jack [P.6]  
20 AUDIO L/R input Jacks [P.6]  
21 Cassette compartment  
POWER  
PICTURE/  
REC  
SLEEP  
SELECT  
22  
23  
34  
35  
1
4
3
6
9
2
5
8
[REMOTE CONTROL]  
24  
CH.  
36  
22 POWER Button [TV/VCR P.9 / DVD P.23]  
23 PICTURE/SLEEP Button [TV/VCR P.9]  
24 Number Buttons [TV/VCR P.9 / DVD P.26]  
25 DISPLAY Button [TV/VCR P.14 / DVD P.28]  
26 SPEED Button [TV/VCR P.18]  
7
VOL.  
DISPLAY  
+100  
37  
0
+10  
25  
SET-UP  
MUTE  
SPEED  
TV/VCR Audio  
26  
27  
28  
38  
39  
27 TV/VCR Audio Button [TV/VCR P14]  
28 PLAY B Button [TV/VCR P.15 / DVD P.23]  
29 REV E Button [TV/VCR P.15 / DVD P.23]  
SKIP H Button [DVD P.26]  
30 PAUSE F Button [TV/VCR P.15 / DVD P.23]  
31 TITLE Button [DVD P.23]  
PLAY  
FWD  
REV  
40  
41  
29  
STOP  
SLOW  
PAUSE  
TITLE  
DISC MENU  
RETURN  
30  
31  
32  
42  
43  
44  
ENTER  
CLEAR  
MODE  
32 CLEAR Button [TV/VCR P.9 / DVD P.26]  
33 MODE Button [DVD P.24]  
34 REC Button [TV/VCR P18]  
35 SELECT Button [TV/VCR P.9]  
45  
33  
K
L
36 CH.  
/
Buttons [TV/VCR P.9]  
Buttons [TV/VCR P.9]  
[FRONT PANEL]  
01 POWER Button [TV/VCR P.9 / DVD P.23]  
02 VOLUME  
X
Y
37 VOL.  
/
38 MUTE Button [TV/VCR P.9]  
K
L
/
Buttons [P.9]  
39 SET-UP Button [TV/VCR P.10 / DVD P.29]  
40 FWD D Button [TV/VCR P.15 / DVD P.23]  
SKIP G Button [DVD P.26]  
41 STOP C Button [TV/VCR P.15 / DVD P.23]  
42 DISC MENU Button [DVD P.23]  
03 SKIP H / G Buttons [DVD P.26]  
SEARCH E / D Buttons [DVD P.23]  
04 PLAY B Button [TV/VCR P.15 / DVD P.23]  
05 STOP C Button [DVD P.23]  
06 OPEN/CLOSE A Button [DVD P.23]  
07 Disc loading tray  
08 DVD Indicator  
09 SELECT Button [TV/VCR P.9]  
10 TV/VCR Indicator  
11 CHANNEL  
12 Recording Indicator  
13 REC/OTR Button [TV/VCR P.18]  
14 REW E Button [TV/VCR P.15]  
15 F.FWD D Button [TV/VCR P.15]  
16 STOP/EJECT C /A Button [TV/VCR P.15]  
43 ENTER Button [TV/VCR P.10 / DVD P.23]  
K
L
44  
/
/{ / B Buttons [TV/VCR P.9 / DVD P.23]  
45 RETURN Button [TV/VCR P.10 / DVD P.25]  
NOTES:  
• We do not recommend the use of universal remote con-  
trols as it may not control all the functions. Note that the  
code number given by universal remote controls may  
not program with this unit. For more details, contact the  
manufacturer of the universal remote control.  
• Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
K
L
/
Buttons [TV/VCR P.9]  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
V OPERATION AND SETTINGS  
T
WATCHING A TV PROGRAM  
SLEEP TIMER / PICTURE CONTROL  
You can set Sleep Timer and picture  
adjustment with [PICTURE / SLEEP].  
TV/VCR  
1 After antenna or cable connection is  
completed, connect the power cord into  
a standard AC outlet.  
TV/VCR  
• The menu changes as described below every time  
you press [PICTURE / SLEEP].  
Sleep Timer  
BRIGHT  
CONTRAST  
COLOR  
2 Press [POWER] to turn on the unit.  
K
L
] or the Number buttons to  
3 Use [CH.  
/
SHARPNESS  
TINT  
select your desired channel number.  
To use the number buttons  
SLEEP TIMER SETTING  
•Single digit channels: (Ex. 02, 03, 04 and so on)  
Press [0] first to select a single digit channel.  
The Sleep Timer function is used to turn off the  
unit without pressing [POWERy] after a desired  
time.  
Two digit channels: (Ex. 12, 38, 95 ...)  
Press two digits directly.  
•Three digit channels: (Ex. 115, 125 ...)  
Press [+100] first, then press the last two digits.  
1 Press [PICTURE / SLEEP] to  
SLEEP 0 MINUTE  
display the Sleep Timer menu.  
X
Y
] to adjust the volume.  
2 Within 5 seconds, set your desired sleep time  
4 Use [VOL.  
/
using [s / B].  
Press [MUTE] to instantly  
mute the sound. Press it again  
to restore the previous sound  
level.  
VOLUME 20  
[B]...Increase by 30 min. (Up to 120 min.)  
[s]...Decrease by 30 min.  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
NOTE:  
NOTE:  
To cancel the Sleep Timer, use [CLEAR] or [s / B]  
• Even if you turn off the unit in the DVD mode, the unit  
will be in the TV/VCR mode when you turn it on again.  
to set the time to "0".  
3 To confirm the remainder time to shutdown,  
press [PICTURE / SLEEP].  
TO WATCH CABLE OR SATELLITE CHANNEL  
If the unit is connected to a cable box or satellite  
box, use [CH. K / L] to select CH3 or CH4 accord-  
ing to the output channel setting of the device and  
select desired channel on that device.  
PICTURE CONTROL  
1 Press [PICTURE / SLEEP]  
BRIGHT  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
repeatedly until desired control  
is displayed.  
TO WATCH EXTERNAL INPUT  
2 Use [s / B] to adjust to your desired level within  
When an external equipment is  
AUX  
5 seconds.  
connected to the front AUDIO/  
VIDEO input jacks, press  
[SELECT] or [CH. K / L] repeat-  
edly until "AUX" appears on the  
screen.  
BRIGHT  
to decrease brightness to increase brightness  
CONTRAST to decrease contrast to increase contrast  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
to green  
to clear  
to purple  
NOTE:  
• If there is no signal input from the antenna terminal  
and no operation for 15 minutes, the unit will turn  
itself off automatically.  
• Even if any power failure occurs, the unit will  
retain its memory for this feature.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
TV OPERATION AND SETTINGS  
AUTOMATIC CLOCK SETTING  
CLOCK SET UP  
NOTES:  
Set the unit clock correctly for VCR timer  
recording. We suggest that you should  
TV/VCR  
• If a cable converter box is being used, make sure it is  
turned on.  
set the clock manually when you first set up the  
unit, then set the auto clock setting to "ON" to cor-  
rect the time periodically.  
You must use the remote control for the clock setting.  
• If the unit is connected directly to a cable converter  
box or satellite box, the local PBS station must be  
selected on the cable box itself and the unit must be  
set to the output channel of the cable converter box  
or satellite box (usually channel 3 or 4), to enable to  
set up or correct the clock automatically.  
NOTE:  
• If you cannot receive a station with time signals, auto  
clock setting is not available. Use manual setting only.  
MANUAL CLOCK SETTING  
1 Press [SET-UP].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
Using [K / L] select "SETTING  
In the example below, the clock is to be set to:  
CLOCK", then press [ENTER].  
DATE:  
May 5th, 2006  
5:40PM  
SETTING TIME:  
– SETTING CLOCK –  
2 Press [ENTER] to select "ON".  
B
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
1 Press [SET-UP].  
Use [K / L] to point to  
"SETTING CLOCK", then  
press [ENTER].  
- TV/VCR SETUP -  
AUTO CLOCK CH  
[ 02 ]  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
B
3 Press [L] to select  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
"AUTO CLOCK CH SEARCH".  
Then press [ENTER].  
B
AUTO CLOCK CH SEARCH  
– SETTING CLOCK –  
2 Use [K / L] to point to  
"MANUAL CLOCK SET", then  
press [ENTER].  
AUTO CLOCK CH  
[ 02 ]  
AUTO CLOCK  
[ON]  
• The unit begins searching for  
the station which contains the  
auto clock set signal. The  
search for a signal may take up  
to 20 seconds per channel.  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
• If there is no local PBS station in  
your area or on your cable sys-  
tem, select "AUTO CLOCK" and press [ENTER]  
[OFF]  
– AUTO CLOCK CH SEARCH –  
08  
10  
13  
to turn "OFF" the function before this step.  
• When the search has finished,  
"_ _" appears at the lower left of  
the screen.  
_ _  
– MANUAL CLOCK SET –  
3 Use [K / L] to set your  
desired month, day, year, hour  
MONTH DAY  
YEAR  
NOTES:  
0 5  
/
:
0 5 FRI  
2 0 0 6  
and minute.  
• During AUTO CLOCK CH SEARCH, the picture may  
be distorted.  
HOUR  
0 5  
MINUTE  
4 0 PM  
Use [s / B] to move to  
another item.  
• If no number appears on the TV screen, there are no  
stations in your area which contain the Auto Clock  
signal. Auto Clock Setting is not possible. Please use  
Manual Clock Setting on this page.  
4 Press [SET-UP].  
5:40 PM  
Although seconds are not  
displayed, they begin counting  
from 00 when you press  
[SET-UP]. Use this feature to  
synchronize the clock with the correct time.  
4 Write down the numbers that appear on the  
screen. They are the auto clock stations in your  
area.  
5 Press [RETURN] to go back to  
NOTE:  
"SETTING CLOCK" menu.  
– SETTING CLOCK –  
• When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
AUTO CLOCK  
[ON]  
L
Press [ ] to select  
AUTO CLOCK CH SEARCH  
"AUTO CLOCK CH".  
B
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 08 ]  
Use [s / B] until you locate an  
auto clock station number.  
[OFF]  
TO CHANGE CLOCK SETTING  
1 Follow steps 1 to 2 above.  
6 Press [SET-UP] to exit the menu.  
2 Select the item you want to change using [B].  
3 Enter correct numbers using [K / L].  
4 Press [SET-UP] to start the clock.  
NOTE:  
• Once the unit is turned off, it will periodically check  
and set the correct date and time.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DAYLIGHT-SAVING TIME  
CLOSED CAPTION SYSTEM  
Select this feature and the unit clock will  
automatically advance one hour in April,  
then reverse one hour in October.  
TV/VCR  
You can view specially labeled (cc) TV  
programs, movies, news and pre-recorded  
tapes with either a dialogue caption or text display.  
TV/VCR  
First Sunday of April : At 2 AM, the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM will  
be canceled.  
- TV/VCR SETUP -  
1 Press [SET-UP].  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
Use [K / L] to point to  
"CAPTION".  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
B
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Last Sunday of October : At 2 AM, the clock  
immediately changes to 1 AM.  
INDEX SEARCH  
V-CHIP SET UP  
2 Press [ENTER] repeatedly to  
select your desired caption  
mode.  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
1 Press [SET-UP].  
B
- TV/VCR SETUP -  
TIMER PROGRAMMING  
TIME SEARCH  
INDEX SEARCH  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
K
L
] to point to  
Use [  
/
"SETTING CLOCK", then  
press [ENTER].  
CAPTION mode: You can watch dramas, movies and  
news while captioning the dialogues and the contents  
of news.  
– SETTING CLOCK –  
2 Use [K / L] to point to "D.S.T.".  
AUTO CLOCK  
[ON]  
TEXT mode: You can watch half screen text informa-  
AUTO CLOCK CH SEARCH  
tion if you want.  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[ON]  
*"CAPTION2" is usually used for a second language (if  
available).  
B
3 Press [SET-UP] to exit the menu.  
3 Press [ENTER] to select "ON".  
NOTES:  
NOTE:  
• Even if any power failure, the unit will retain its mem-  
ory for this feature.  
To cancel the setting, select "OFF".  
• Some programs are not broadcasted with closed  
captions. The unit is designed to provide error-free  
closed captions with high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
4 Press [SET-UP] to exit the menu.  
• Common signal conditions which may cause caption  
errors are listed below:  
ON-SCREEN MENU LANGUAGE  
- Electric motor brush noise  
You can select the language of on-screen  
menu among English, Spanish and French.  
TV/VCR  
- Weak snowy reception on TV screen  
- Multiplex signal reception displaying picture  
ghosts or airplane flutte  
1 Press [SET-UP].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
• If the unit displays a black box on  
the TV screen, this means that  
the unit is set to the TEXT mode.  
To clear screen, select "CAP-  
TION1", "CAPTION2" or "OFF".  
Use [  
K / L] to point to  
"LANGUAGE".  
B
TIME SEARCH  
INDEX SEARCH  
2 Press [ENTER] repeatedly to select "ENGLISH",  
"ESPAÑOL" or "FRANÇAIS".  
TO CANCEL THE CLOSED CAPTION SYSTEM  
3 Press [SET-UP] to exit the menu.  
1 Press [SET-UP]. Use [K / L] to point to  
"CAPTION".  
NOTES:  
• This function effects only the language on the screen  
menu and not the audio source.  
2 Press [ENTER] repeatedly to select "OFF".  
• If for some reason the menu is already in Spanish or  
French, press [SET-UP], using [K / L] point to  
"IDIOMA [ESPAÑOL]" or "LANGAGE [FRANÇAIS]",  
then press [ENTER] repeatedly to select desired lan-  
guage, then press [SET-UP].  
3 Press [SET-UP] to exit the menu.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
TV OPERATION AND SETTINGS  
A
TV RATING SET UP  
V-CHIP SET UP  
4 Use [K / L] to select a rating  
This feature enables parents to prevent  
their children from watching inappropriate  
material on TV. When you try to access a blocked  
program, “PROTECTED PROGRAM by ...mes-  
sage appears on the TV screen.  
TV/VCR  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
that you wish to block.  
(
)
)
)
)
Press [ENTER] repeatedly to  
set it to "BLOCK" or "VIEW".  
(
Selection Rating Category Explanations  
TV-Y  
NOTE:  
Appropriate for all children  
Appropriate for children seven and older  
General Audience  
Parental Guidance suggested  
Unsuitable for children under 14  
Mature audience only  
To change the rating, the TV  
must be turned to an unprotect-  
ed program. If the screen on the  
right is displayed, change the  
channel to a station that is not  
protected.  
TV-Y7  
TV-G  
TV-PG  
TV-14  
TV-MA  
PROTECTED PROGRAM  
by TV-Y  
1 Press [SET-UP].  
- TV/VCR SETUP -  
NOTES:  
TIMER PROGRAMMING  
Use [  
K / L] to select  
• When you select a rating and set  
it to "BLOCK", the higher ratings  
will be blocked automatically.  
The lower ratings will be avail-  
able for viewing.  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
EO RU
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
"V-CHIP SET UP", then press  
[ENTER].  
B
(
)
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
2 Use the Number buttons to  
ACCESS CODE  
• When you set the lowest rating to  
"VIEW", all other ratings will be automatically avail-  
able for viewing.  
enter the access code.  
_
_
_
_
• For the first time set-up or in  
the event the unit has lost  
power, enter the default code of 0000.  
5 The TV-Y7, TV-PG, TV-14 and  
TV-MA ratings have the option  
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
3 Use [K / L] to select "TV RATING", "MPAA  
RATING" or "CHANGE CODE", then press  
[ENTER].  
B
(
)
of sub rating categories.  
Use [K / L] to select a rating  
with sub-ratings, then press  
[ENTER] twice.  
)
)
)
(
Refer to the pages below to set up each item.  
– V-CHIP SET UP –  
6 Use [K / L] to select a sub-  
rating, then press [ENTER] to  
set it to "BLOCK" or "VIEW".  
P 12  
P 13  
P 13  
A
B
C
B TV RATING  
MPAA RATING  
CHANGE CODE  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
NOTE:  
• The blocked sub-ratings will  
appear next to the rating cate-  
gory in the "TV RATING" menu.  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
Selection Rating Category Explanations  
TV-Y7  
FV  
Fantasy Violence  
TV-PG, TV-14, TV-MA  
D
L
Suggestive Dialog (TV-PG, TV-14 only)  
Coarse Language  
S
V
Sexual Situation  
Violence  
7 Press [SET-UP] to exit the menu.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
B
C
MPAA RATING SET UP  
CHANGE ACCESS CODE  
4 Use [K / L] to point to your  
desired item, then press  
[ENTER] to select "BLOCK"  
or "VIEW".  
4 Use the Number buttons to  
enter your desired access  
code in the "NEW CODE",  
then enter the same code in  
the "CONFIRM CODE". When  
completed, the menu will  
G
[VIEW]  
PG  
[VIEW]  
NEW CODE  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
X X X X  
CONFIRM CODE  
_
_
_
_
Selection Rating Category Explanations  
return to "V-CHIP SET UP".  
G
General Audience  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires acco-  
mpanying parent or adult guardian  
No one under 17 admitted  
Mature audience only  
5 Press [SET-UP] to exit the menu.  
NOTE:  
Your personal access code will be erased and will  
return to the default (0000) when a power failure  
occurs or when you turn off the power using a wall  
switch. If you forget the code, unplug the power cord  
for 10 seconds to restore the access code to 0000.  
NC-17  
X
5 Press [SET-UP] to exit the menu.  
CHANNEL SET UP  
Channel presetting is necessary at the start or in case you moved the TV to a different area.  
TV/VCR  
AUTO CHANNEL PROGRAMMING  
ADDING/DELETING CHANNELS  
1 Press [SET-UP].  
You can add channels that was not memorized due  
to the bad reception status and also delete chan-  
nels you no longer receive or seldom watch.  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Use [K / L] to point to  
B
"CHANNEL SET UP", then  
press [ENTER].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
1 Press [SET-UP].  
Use [K / L] to point to  
B
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
– CHANNEL SET UP –  
2 Use [K / L] to point to "AUTO  
CH PROGRAMMING", then  
press [ENTER].  
"CHANNEL SET UP", then  
press [ENTER].  
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
B
The tuner scans and memorizes all the active  
channels in your area.  
– CHANNEL SET UP –  
2 Use [K / L] to point to  
"ADD/DELETE CH", then  
press [ENTER].  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
3 When the scanning is comple-  
CH 15  
ted, the lowest memorized  
channel is displayed.  
3 Use the Number buttons or  
[CH. K / L] to select your  
desired channel number.  
(You can also use [K / L] to  
enter it.)  
<EXAMPLE>  
08  
If "NO TV SIGNALS" appears  
on the TV screen, check the  
antenna connection and try  
again.  
ADD / DELETE  
NO TV SIGNALS  
• Refer to page 9 on how to use  
the Number buttons.  
(Example: CH8)  
NOTES:  
• The unit may recognize CATV channels to be TV  
channels if reception condition is poor. In this case,  
check the antenna connection and try "AUTO CH  
PROGRAMMING" again.  
4 Press [ENTER] repeatedly. The channel number  
changes to red (deleted) or blue (added) every  
time you press the button.  
To delete another channel, repeat steps 3 to 4.  
Auto channel programming is NOT necessary  
when connected to a cable box or satellite box.  
Just select the channel for cable box or satellite  
input (ex. CH3 or CH4) on the unit, then select  
your desired channel on the cable box or satellite  
box.  
5 Press [SET-UP] to exit the menu.  
NOTE:  
To confirm that channel(s) has been deleted or  
added, select it (them) using [CH. K / L].  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
N-SCREEN DISPLAY  
O
STATUS DISPLAY  
CHECKING THE STATUS  
On screen display examples are shown  
below.  
While receiving a broadcast or playing a  
VHS tape, you can check the status dis-  
TV/VCR  
TV/VCR  
played on the screen by pressing [DISPLAY]. You  
can also check the status of the preset MTS (Multi-  
Channel Television sound). The display will change  
as shown below each time you press [DISPLAY].  
4
5
6
PLAY  
HIFI  
B
12:00AM  
CH 123  
STEREO/SAP  
1
2
WHEN THE CLOSED CAPTION IS OFF  
7
SP  
COUNT 0:00:00  
3
The display switches among VCR counter and clock.  
1. VCR status  
Display OFF  
COUNTER display  
CLOCK display  
Displays the current VCR motion:  
PLAY / STOP / REC / OTR / PAUSE / FF / REW  
STOP  
5:40PM  
CH2  
STOP  
2. VCR sound mode status (during playback)  
Displays "HIFI" when the tape is recorded in  
Hi-Fi stereo mode.  
SP  
SP  
COUNT 0:12:34  
After 5 seconds  
After 5 seconds  
3. Tape speed (during recording)  
5:40PM  
CH2  
Displays the tape speed: SP / SLP  
4. Clock  
COUNT 0:12:34  
5. Channel number (in TV mode)  
Displays the current channel number.  
"AUX" is displayed in external input mode.  
WHEN THE CLOSED CAPTION IS ON  
6. MTS status (in TV mode)  
Displays the current sound status of the broad-  
cast: STEREO / SAP  
The display switches among VCR counter and clock.  
Display OFF  
CLOCK/COUNTER  
display  
7. Tape counter (during playback or recording)  
Shows the elapsed recording or playback time.  
(Not available for a blank tape or blank portions  
on the tape.) You can reset the counter by press-  
ing [CLEAR].  
STOP  
5:40PM  
CH2  
*The display will disappear  
after 5 seconds  
SP  
COUNT 0:12:34  
MTS (Multi-channel Television Sound) SYSTEM  
MTS allows for reception of sound other than the main audio program. You can listen or record  
monaural audio sound, stereo sound or Secondary Audio Program (SAP).  
TV/VCR  
WHEN RECEIVING AN MTS BROADCAST  
WHEN PLAYING CASSETTES  
Press [TV/VCR Audio] repeatedly to select a sound  
Press [TV/VCR Audio] repeatedly to select "HIFI"  
mode when you watch or record a TV program.  
or "MONO".  
• The mode changes according to  
the broadcast among "STEREO",  
"SAP" and "MONO" every time  
• This setting is saved until the cassette is ejected.  
NOTE:  
STEREO  
• The initial setting is "HIFI". When you play non-HIFI tapes,  
the unit will play only in the monaural mode even if the  
setting is "HIFI".  
you press the button.  
NOTES:  
• The initial setting is "STEREO". The unit records auto-  
matically MTS broadcasts in Hi-Fi stereo sound unless  
you select "SAP" beforehand.  
(
)
WHEN IN THE EXTERNAL INPUT "AUX" MODE  
Any output mode setting does not affect the audio  
output and the current audio output mode does not  
appear on the TV screen.  
• If you select "SAP" when second audio is not available,  
the unit will record in normal audio.  
• This setting returns to the initial value when you turn off  
the unit or unplug the power cord.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
IDEO CASSETTE  
V
This unit will operate with any cassette that has the  
mark. For best results, we recommend the  
use of high-quality tapes. Do not use poor quality or  
damaged tapes.  
ERASE PREVENTION  
Break off the tab on the  
back edge of the cassette  
to prevent accidental eras-  
ing of recording.  
SELECTING TAPE SPEEDS  
Tab  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).You can also play a tape recorded in LP mode  
(Long Play).  
Cover the hole with plastic  
tape to record on the tape  
again.  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback time  
T60  
T120  
T160  
1 hour  
2 hours 2-2/3 hours  
Plastic Tape  
SLP mode  
3 hours 6 hours 8 hours  
NOTES:  
• In the TV/VCR mode, if the cassette without tab is insert-  
ed, playback will start automatically.  
• If you press [REC/OTR] or [REC] when a cassette with-  
out tab is inserted, the unit will eject it automatically.  
LAYBACK  
P
BASIC PLAYBACK  
TRACKING ADJUSTMENT  
1 Insert a pre-recorded tape so that the  
unit turns on automatically (Auto  
Power On).  
Tracking adjustment will be set automatically when  
you start playback (Digital tracking function).  
TV/VCR  
• If noise lines (black and white streaks) appear on  
the playback picture, use [CH. K / L] until the  
streaks disappear (Manual tracking adjustment).  
This is available in Pause/Still/Slow mode, too.  
2 Select TV/VCR mode by pressing [SELECT].  
To release manual tracking mode, stop the tape  
once and start playback again.  
NOTE:  
• If the erase-prevention tab has been removed, the  
unit will change the VCR mode and starts playback  
automatically.  
STILL PICTURE  
• During playback, press [PAUSE F] to freeze the  
picture.  
You can advance the picture frame by frame by  
pressing [PAUSE F] repeatedly.  
3 To start playback,  
B
PLAY  
press [PLAY B].  
NOTE:  
• Even in the DVD mode, you can start the VCR play-  
back if you press [PLAY B] on the front panel (of  
the TV/VCR side).  
To release the Still mode, press [PLAY B].  
SLOW MOTION  
STOP  
4 To stop the playback,  
• During playback, press [PAUSE F] then press  
[FWDD].  
press [STOP C].  
E
REW  
5 To rewind the tape,  
To release the Slow mode, press [PLAY B].  
press [REVE].  
NOTE:  
To forward the tape,  
press [FWDD].  
To stop winding, press [STOP C].  
D
FF  
• If the unit keeps the slow mode or still mode for more  
than 5 minutes, it will automatically enter the stop mode.  
A
EJECT  
6 To eject the tape from the unit,  
press [STOP/EJECT C /A]  
on the front panel.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
PECIAL PLAYBACK  
S
RENTAL PLAYBACK  
AUTO REPEAT PLAYBACK  
This function enables you to improve the  
picture quality when playing back worn  
cassettes such as rented tapes.  
This function allows you to repeat a tape  
indefinitely.  
TV/VCR  
TV/VCR  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
1 Press [SET-UP].  
Use [K / L] to point to  
"USER’S SET UP", then press  
[ENTER].  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
1 Press [SET-UP].  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
B
Use [K / L] to point to  
"USER’S SET UP", then press  
[ENTER].  
B
2 Use [K / L] to point to "REPEAT PLAY".  
USER’S SET UP  
K
L
] to point to  
Press [ENTER] repeatedly  
2 Use [  
/
USER’S SET UP  
"RENTAL".  
Press [ENTER] to select "ON".  
until your desired selection  
"ALL" or "BLANK" appears.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
ALL:  
Repeat playback from the  
beginning to the end of the tape.  
NOTE:  
To cancel the setting, select "OFF" at this step.  
BLANK: Repeat playback from the beginning to a part,  
which is blank for more than 10 seconds.  
Cancel repeat playback.  
3 Press [SET-UP] to exit the menu.  
OFF:  
4 Press [PLAY B] to start  
RENTAL PLAY  
B
3 Press [SET-UP] to exit the menu.  
playback.  
NOTE:  
REPEAT PLAY  
B
4 Press [PLAY B] to start the  
• This setting will not change even if you turn off the  
unit.  
Repeat Play.  
NOTES:  
• If the rental mode is set to "ON", “RENTAL PLAY B”  
display has priority.  
• This setting will not change even if you turn off the  
unit.  
EARCH FUNCTION  
S
ZERO RETURN  
- TV/VCR SETUP -  
4 Press [SET-UP].  
TIMER PROGRAMMING  
This function allows you to search easily  
a beginning point that you want to review  
by rewinding or fast forwarding.  
SETTING CLOCK  
CHANNEL SET UP  
TV/VCR  
Use [K / L] to point to "ZERO  
USER’S SET UP  
V-CHIP SET UP  
RETURN", then press  
[ENTER].  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
B
NOTE:  
The unit will begin rewinding  
and the counter will appear on the TV screen.  
• Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
The tape will automatically stop when the  
counter returns to 0:00:00 (approx.).  
1 Rewind or forward the tape to the beginning  
point at which you want to review.  
2 Press [CLEAR] repeatedly to  
COUNT  
0:00:00  
set the counter to "0:00:00".  
3 Press [PLAY B] for playback or [REC] for  
recording.  
Press [STOP C] when playback or recording is  
completed.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PICTURE SEARCH  
INDEX SEARCH  
This function is useful in finding or  
skipping over a particular scene on a  
tape. In this mode, the sound will be muted.  
TV/VCR  
This function allows you to index the  
starting point to make it easy to reach  
TV/VCR  
the point in either fast forward or rewind mode.  
1 During playback, press [REV E] or [FWD D]  
• Every time you start recording, an index is marked  
automatically. The index mark also works as the  
starting point of Timer recording and OTR.  
to view at a high speed (in forward/reverse).  
2 Press [REV E] or [FWD D] again to view at  
• The index mark will not be recorded if [PAUSE F]  
is used during recording.  
super high speed (in LP/SLP modes only).  
NOTE:  
• The time gap between making the index marks on  
the tape should be greater than 1 minute for SP  
recording, 2 minutes for LP recording and 3 min-  
utes for SLP recording.  
Tapes recorded in the SP or LP mode will normally  
display a noise bar on the TV screen and the picture  
may revert to black and white.  
3 Press [PLAY B] to return to normal playback.  
• In some cases, the index mark at the beginning of  
video tape cannot be detected.  
Example: You are watching program number 4 and  
want to fast forward to program number  
7. Skip three programs.  
TIME SEARCH  
This function allows you to quickly  
advance the tape to your desired posi-  
tion simply by entering the exact amount of playback  
time you want to skip.  
TV/VCR  
CURRENT PLAYBACK PROGRAM  
Beginning of  
the tape  
End of  
the tape  
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7  
In the example below: To watch a program before/  
after 2 hour 50 minutes from the present position,  
in either direction.  
4
3
2
1
1
2
3
INDEX MARK  
- TV/VCR SETUP -  
1 Press [SET-UP].  
TIMER PROGRAMMING  
SETTING CLOCK  
1 Press [SET-UP].  
Use [K / L] to point to  
- TV/VCR SETUP -  
Use [K / L] to point to "TIME  
CHANNEL SET UP  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
USER’S SET UP  
V-CHIP SET UP  
SEARCH", then press  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
"INDEX SEARCH", then press  
[ENTER].  
[ENTER].  
B
TIME SEARCH  
INDEX SEARCH  
B
2 Use [K / L] until your desired  
time appears.  
TIME SEARCH  
2 : 50  
2 Use [K / L] until the number  
of programs that you want to  
skip appears.  
INDEX SEARCH  
0 3  
To cancel the Time Search at  
this point, press [SET-UP].  
NOTE:  
3 Use [s / B]. The unit begins rewinding or fast  
• Time Search can be set up to a maximum of 9 hours  
50 minutes (9:50) by 10 minutes at a time.  
forwarding to the beginning of desired program.  
4 When the search is completed, the unit will start  
3 Use [s / B] to rewind or fast forward to the  
playback automatically.  
specified point.  
• The numbers of Index Search can be set up to  
20.  
• This function is not available during recording.  
The time counts down during the search. When  
the counter reaches "0:00:00", the tape will start  
playback automatically.  
TO CANCEL DURING INDEX SEARCH  
TO CANCEL DURING TIME SEARCH  
Press [STOP/EJECT C /A] on the unit or [STOP C].  
Press [STOP/EJECT C /A] on the unit or [STOP C].  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
ECORDING  
R
NOTES:  
OTR (One Touch Recording)  
• Insert a cassette tape with its erase-prevention tab in place.  
• This unit cannot record the contents from the built-in DVD.  
You can ONLY watch the same TV program that is being  
recorded.  
This function enables you to start record-  
ing for specified length simply by press-  
ing [REC/OTR] on the unit.  
TV/VCR  
K
L
] or the Number buttons to  
1 Use [CH.  
/
NORMAL RECORDING  
select the channel to be recorded.  
K
L
1 Use [CH.  
/
] or the Number  
TV/VCR  
CH 10  
NOTE:  
buttons to select the channel to  
• If the unit is connected to a cable box or satellite  
box, the unit must be on CH3 or CH4. Select the  
channel to be recorded on the cable box or satellite  
box.  
be recorded.  
NOTE:  
• If the unit is connected to a cable box or satellite  
box, the unit must be on CH3 or CH4. Select the  
channel to be recorded on the cable box or satellite  
box.  
2 Press [SPEED] to select the desired tape speed  
(SP/SLP).  
(Refer to "SELECTING TAPE SPEEDS" on page 15.)  
2 Press [SPEED] to select the  
OTR (2 : 30)  
desired tape speed (SP/ SLP).  
3 Press [REC/OTR] on the unit  
SP  
(Refer to "SELECTING TAPE  
SPEEDS" on page 15.)  
repeatedly until your desired  
length appears on the screen.  
The recording time will increase  
REC  
3 Press [REC] to start recording.  
by 30 minutes up to 8 hours.  
SP  
Recording starts immediately when you press  
[REC/OTR].  
SP  
NOTE:  
• If you press [REC/OTR] when "8:00" is displayed,  
the unit returns to the normal recording mode.  
4 Press [PAUSE F] to tempo-  
PAUSE  
rarily stop recording unwanted  
scenes.  
Time(s)  
1 time  
2 times  
3 times  
Display  
Recording length  
(normal recording)  
Press [PAUSE F] again or  
[REC] to resume recording.  
0:30  
1:00  
30 minutes  
60 minutes  
SP  
NOTE:  
• If the recording is paused for more than 5 minutes,  
the unit will automatically switch to the recording  
mode to prevent tape damage.  
17 times  
8:00  
480 minutes  
NOTES:  
• Even if you press [POWER] during OTR, the unit  
5 Press [STOP C] to stop recording.  
continues recording.  
You cannot start OTR with the remote control.  
• In the SLP mode, maximum recording time, assum-  
ing the tape starts at the beginning, is 8 hours using  
T-160 (or 6 hours using T-120).  
• If the tape runs out before the end time, the unit will  
switch to the stop mode immediately, eject the tape  
and turn itself off.  
To show the remaining time of OTR, press [DISPLAY]  
on the remote control to display "OTR" on the TV  
screen. (It will show up momentarily then disappear.)  
TO CANCEL OTR IN PROGRESS  
Press [STOP/EJECT C /A] on the unit or [STOP C].  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
AUTOMATIC TIMER RECORDING  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
61 7/03 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
5 Use [K / L] to set the desired  
begin/end hour and minute.  
You can set 8 programs to record on  
TV/VCR  
M
8:50PM- -  
-:- - - -  
-:- - - -  
B
specific days, daily or weekly within  
1 year period.  
Press [B] to move to next item.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
61 7/03 MON 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
6 Use [K / L] until the desired  
tape speed appears.  
In the example below, the timer is being set to record:  
M
8:50PMSP  
-:- - - -  
-:- - - -  
B
DATE:  
July 3rd, 2006  
(Refer to "SELECTING TAPE  
SPEEDS" on page 15.)  
SETTING TIME: from 7:30PM to 8:50PM  
CHANNEL:  
CH61  
SP  
7 Press [ENTER] to complete setting.  
TAPE SPEED:  
To set another program, repeat steps 2 to 7.  
To correct the program while setting, press [s]  
- TV/VCR SETUP -  
1 Press [SET-UP].  
K
L
] to enter  
to go back one step and use [  
/
B
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Use [K / L] to select  
"TIMER PROGRAMMING",  
then press [ENTER].  
the correct numbers.  
• Press [SET-UP] to exit the menu.  
8 Press [POWER] to set automatic timer recording.  
NOTE:  
The recording indicator lights up.  
• If you have not yet set the clock, "MANUAL CLOCK  
SET" menu appears. Set to the present time and  
date (refer to "MANUAL CLOCK SETTING" on page  
10) then start setting the timer recording.  
NOTES:  
You MUST turn off the unit to activate automatic  
timer recording.  
• If power is not turned off and  
you continue watching TV,  
– TIMER PROGRAMMING –  
2 Use [K / L] to select the  
CH DATE  
BEGIN END  
"TIMER REC STANDBY" starts  
desired program position, then  
TIMER REC STANDBY  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- -  
-:- -  
-:- -  
-:- -  
- -  
- -  
- -  
- -  
B
flashing on the TV screen 2 min-  
utes before the programmed  
start time.  
• Make sure a cassette with erase-prevention tab is  
inserted before turning off the unit. If the cassette does  
not have the tab, it will be ejected when you press  
[POWER] to turn off.  
press [B].  
– TIMER PROGRAMMING –  
3 Use [  
K / L] until the desired  
channel number appears, then  
CH DATE  
BEGIN END  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- -  
-:- -  
-:- -  
-:- -  
- -  
- -  
- -  
- -  
B
press [B].  
NOTE:  
9 At the programmed start time, the unit begins  
• If the unit is connected to a cable box or satellite box,  
the unit must be on CH3 or CH4. Select the channel  
to be recorded on the cable box or satellite box.  
recording.  
NOTES:  
• The recording starts without turning on the TV screen.  
4 Set the starting date.  
During recording, you can watch only currently  
being recorded TV program or DVD playback.  
Press [POWER] and [SELECT] to select the desired  
mode.  
• If the tape runs out before the end time, the recording  
stops immediately and the cassette will be ejected.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
For once recording :  
K
Press [ ] until the desired  
61 7/03 MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- -  
-:- -  
-:- -  
-:- - - -  
- -  
- -  
- -  
B
date appears. Then press [B].  
For every day recording :  
To record the same channel  
at the same time every day.  
TIMER PROGRAMMING
CH DATE  
BEGIN END  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
B
TO CONFIRM THE PROGRAM  
Press [L] until "EVRY DAY"  
appears, then press [B].  
1 Press [POWER] to turn on the unit.  
(The Recording indicator turns off.)  
For weekly recording :  
To record the same channel  
at the same time every week.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
2 Press [SET-UP].  
Use [K / L] to select "TIMER PROGRAMMING",  
then press [ENTER].  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- -  
-:- -  
-:- -  
- -  
- -  
- -  
B
L
Press [ ] until "EVRY" and  
your desired day of the week  
(Ex. Every Monday) appear,  
then press [B].  
3 Confirm the details of programs that appear on  
the TV screen.  
4 Press [SET-UP] to exit the menu.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV/VCR SECTION  
RECORDING  
ABOUT OVERLAP OF PROGRAMS  
TO CORRECT A PROGRAM AFTERWARD  
When programs overlap, a program may not be  
recorded.  
1 Press [POWER] to turn on the unit.  
2 Repeat steps 1 to 2 of "AUTOMATIC TIMER  
• The program with an earlier start has priority.  
• Once the earliest program finishes, the overlapping pro-  
grams will begin recording in sequence.  
• When the starting time is the same, the program set on  
the highest position in the program list has priority.  
• The illustration below demonstrates the sequence of  
recordings.  
RECORDING" on page 19.  
3 Press [B] (or press [s] to go back one step)  
until the part you want to correct begins flashing,  
then use [K / L] to make the changes.  
Press [ENTER] to confirm.  
4 Press [POWER] to set automatic timer recording.  
Recording Sequence  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
9:30AM-12:00PM  
TO CANCEL A PROGRAM  
1 Press [POWER] to turn on the unit.  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
2 If recording is in progress, press  
*Recording period is SHADED  
[STOP/EJECT C /A] on the unit.  
TIMER PROGRAM EXTENSION  
3 Press [SET-UP].  
Use [K / L] to select "TIMER PROGRAMMING",  
then press [ENTER].  
You can shift the time schedule of an automatic timer  
recording after programming or during recording.  
4 Use [K / L] to select a program you want to  
1 Press [POWER] to turn on the unit.  
cancel and press [CLEAR].  
2 Press [SET-UP].  
5 Press [SET-UP] to exit the menu.  
Use [K / L] to select "TIMER PROGRAMMING",  
then press [ENTER].  
– TIMER PROGRAMMING –  
3 Press [REC] and use  
CH DATE  
BEGIN END  
[K / L] to select the desired  
61 7/03 MON 7:30P  
M
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
B
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
program.  
4 Press [REC] repeatedly until your desired  
begin/end time appears.  
Each press will shift forward the begin/end time  
for recording by 10 minutes.  
NOTES:  
• When the recording is already in progress, each  
press will shift forward the end time only.  
• If you want to cancel while setting, press [PAUSE F]  
on the remote control. The recording time returns to  
the original time.  
• When you shift forward the time schedule during  
recording, the recording speed will be automatically  
set to the SLP mode.  
5 Press [ENTER] to complete the setting. Then  
press [SET-UP] to exit the menu.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
AUTO RETURN  
This function allows you to automatically  
search the beginning of the recorded  
program(s) after timer recording finishes.  
COPYING A VIDEO CASSETTE  
(from another source)  
TV/VCR  
You can make copies of video tapes for  
your enjoyment.  
You CANNOT copy a DVD to a videotape.  
TV/VCR  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
1 Press [SET-UP].  
Use [K / L] to point to  
"USER’S SET UP",  
then press [ENTER].  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
WARNING: Unauthorized recordings of copyrighted  
video tapes may be an infringement of copyright  
laws.  
B
USER’S SET UP  
2 Use [K / L] to point to  
"AUTO RETURN", then press  
[ENTER] to select "ON".  
Connect the unit and a source (for playing) device  
as shown the following diagram.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
B
[This unit]  
3 When all the timer recordings are completed, the  
unit will rewind to the beginning of the recorded  
program(s) and then turn itself off.  
NOTE:  
[Ex: Jacks of  
source device]  
• If you turn off the unit while rewinding the tape, the  
AUTO RETURN will stop.  
Audio/Video  
cables  
AUDIO  
(not supplied)  
L
OUT  
IN  
TO CANCEL THE AUTO RETURN MODE  
R
VIDEO  
Repeat steps 1 to 2 and press [ENTER] to select  
OUT  
IN  
"OFF".  
• Even if any power failure occurs, the unit will  
retain its memory for this feature.  
1 Insert a pre-recorded video cassette into the  
source device (VCR, camcorder, etc.).  
2 Insert a video cassette to record into this unit’s  
cassette compartment.  
3 Press [SPEED] to select the  
desired recording speed  
(SP/SLP).  
SP  
AUTO REWIND-EJECT  
• When the end of a tape is reached  
during recording, playback, or fast-  
forward, the tape will automatically rewind to the  
beginning. After rewinding finishes, the unit will  
eject the tape and turn itself off.  
TV/VCR  
4 Press [SELECT] until "AUX"  
AUX  
appears on the screen.  
5 Press [REC/OTR] on the unit.  
• This function is operative when REPEAT PLAY is  
set to "OFF".  
6 Begin playback of the tape  
in the source device.  
• The tape will not auto-rewind during timer record-  
ing or One Touch Recording (OTR).  
NOTE:  
• For best results during copying, use the front panel  
controls whenever possible. The remote control might  
affect the operation of the source device.  
7 To stop copying, press [STOP/EJECT C /A] on  
the unit, then stop the playback on the source  
device.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DVD SECTION  
BOUT THE DISCS  
A
PLAYABLE DISCS  
Playable  
discs  
Region Recorded Disc  
Mark (logo)  
Disc types  
code  
signals size  
DVD-Video  
* 1,2,4,6,  
or  
10,11  
Digital  
12 cm  
Example  
DVD-RW  
DVD-R  
Title 1  
Title 2  
video  
or  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1  
Chapter 2  
-
-
(MPEG2)  
8 cm  
* 1,3,4,5,  
6,7,9,10  
DVD+RW  
DVD+R  
* 1,3,4,5,6,8,9,10  
Audio CD  
* 4,6,10  
Example  
12 cm  
or  
8 cm  
Digital  
audio  
-
CD-RW  
CD-R  
Track 1  
Track 2  
Track 5  
Track 6  
Track 3  
Track 4  
* 4,5,6,9,10  
is a trademark of DVD Format/Logo Licensing Corporation.  
If you cannot play back a disc which bears one of the marks above, check the following notes.  
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot  
be played back.  
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc's producers.  
*3: Discs recorded in the VR (Video Recording) format cannot be played back.  
*4: Scratched or stained discs may not be played back.  
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the  
recorder or special properties of discs.  
*6:You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may  
not play them back. Even if they are played back, the sound or video quality will be compromised.  
*7:You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand's DVD  
recorder. However, depending on the recording status of a disc, the disc may not be played back at all  
or normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc  
with the DVD recorder. Refer to the manual accompanying the DVD recorder.  
*8: Only the discs recorded in the video format and finalized can be played back.  
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not  
be played back at all or normally (the picture or sound may not be smooth, etc.).  
*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may  
not play back properly.  
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read  
it correctly.  
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region  
format can only be played back on unit with the same region code.  
UNPLAYABLE DISCS  
NEVER play back the following discs. Otherwise, malfunction may result!  
DVD-RAM / CD-i / Photo CD / Video CD / DVD-Audio / DVD with region codes other than 1 or ALL /  
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3  
The sound MAY NOT be heard: Super Audio CD  
NOTE:  
Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density Super Audio  
CD layer cannot be delivered.  
Any other discs without compatibility indications  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
LAYING A DISC  
P
FAST FORWARD / FAST REVERSE  
BASIC PLAYBACK  
• During playback, press and hold  
[FWD D] for fast forward or  
[REV E] for fast reverse.  
1 Press [POWER] to turn on the  
unit.  
• Every time you press and hold  
the button, playback speeds up  
and the level of the speed  
appears on the screen.  
D1  
2 Press [OPEN/CLOSE A] on the unit.  
3 Place the disc in the tray, with  
the label facing up.  
NOTES:  
• For DVDs, fast forward/reverse speed is different  
depending on the disc. Approximate speed is 1 (×2),  
2 (×8), 3 (×20), 4 (×50) and 5 (×100).  
4 Press [PLAY B].  
• The tray will close automatically and playback will  
start. When you play back a DVD which features a  
title menu, it may appear on the screen.  
• For Audio CDs approximate speed is 1 (×2), 2 (×8)  
and 3 (×30).  
• When you use buttons on the front panel, use  
[SEARCH E / D].  
NOTES:  
• Closing the disc tray manually or by pressing  
[OPEN/CLOSE A] also starts playback.  
To return to normal playback, press [PLAY B].  
SLOW FORWARD / SLOW REVERSE  
• With DVDs that use titles for play back program sig-  
nals, playback may start from the second title or it may  
skip these titles.  
• During playback, press [PAUSE F].  
• Press and hold [FWD D] for slow for-  
ward or [REV E] for slow reverse.  
5 To freeze the picture, press [PAUSE F] during  
playback.  
• Every time you press and hold  
1
the button, playback is slowed  
down and the level of the speed  
appears on the screen.  
NOTE:  
• The sound will be muted in pause mode.  
6 Press [STOP C] to stop  
NOTES:  
playback temporarily.  
Resume ON  
• Slow forward / reverse speed varies with the disc.  
Approximate speed is 1 (1/16), 2 (1/8) and 3 (1/2).  
Press 'PLAY' to play from here.  
To play the beginning,  
press 'STOP' first and then 'PLAY'.  
• Press [PLAY B] to resume  
the playback.  
To cancel resume and stop the  
disc, [STOP C] again.  
• When you use buttons on the main unit, use  
[SEARCH E / D].  
To return to normal playback, press [PLAY B].  
NOTES:  
• The resume information stays on even if the unit is  
turned off.  
• A "prohibited icon" may appear  
at the top-right on the TV screen  
during operation. This means  
DISC MENU / TITLE MENU  
DVD may contain menus to navigate the  
disc and access special features.  
that the operation is not available on the disc.  
1 Press [DISC MENU] or [TITLE].  
• The DVD main menu / the title menu will appear.  
You can call up the menu even during playback.  
STEP BY STEP PLAYBACK  
• During playback, press [PAUSE F].  
You can advance the picture frame by  
frame by pressing [PAUSE F] repeatedly.  
K
L
2 Use [  
/
/
s / B] to select an item, and press  
[ENTER].  
To return to normal playback, press [PLAY B].  
NOTES:  
• If disc menu is available on the disc, audio language,  
subtitle options, chapters for the title and other  
options will appear for selection.  
• Contents of menu and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DVD SECTION  
PECIAL PLAYBACK FUNCTIONS & SETTINGS  
S
FUNCTION TABLE  
Setting menu switches as below every time you press [MODE] during playback.  
See the reference page for how to set each menu. Some functions are not available in specific  
modes, but this is not a malfunction.  
DVD-V  
CD  
Press [MODE]  
Press [MODE]  
AUDIO STREAM 1  
...  
AUDIO STREAM 8  
STEREO  
L-ch  
R-ch  
AUDIO MENU (p25)  
AUDIO MENU (p25)  
V.S.S. MENU (p26)  
SEARCH MENU (p26)  
REPEAT MENU (p27)  
A-B REPEAT MENU (p27)  
MENU OFF  
OFF  
OFF  
1
2
SUBTITLE MENU (p25)  
SUBTITLE STREAM 1  
....  
SUBTITLE STREAM 32  
TRACK SEARCH  
TIME SEARCH  
MARKER SEARCH  
ANGLE 1  
....  
ANGLE 8  
ANGLE MENU (p25)  
(If available)  
OFF  
TRACK  
ALL  
OFF  
ZOOM MENU (p25)  
ZOOM 1 (×1.3)  
ZOOM 2 (×2.0)  
ZOOM 3 (×4.0)  
OFF  
A-  
A-B  
OFF  
ON  
BLACK LEVEL MENU (p26)  
V.S.S. MENU (p26)  
OFF  
1
2
SEARCH MENU (p26)  
CHAPTER SEARCH  
TITLE SEARCH  
TIME SEARCH  
MARKER SEARCH  
OFF  
CHAPTER  
TITLE  
REPEAT MENU (p27)  
A-B REPEAT MENU (p27)  
MENU OFF  
OFF  
A-  
A-B  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ANGLE MENU  
AUDIO MENU  
Some DVD discs contain scenes which  
have been shot from various angles and  
you can change them as you like.  
AUDIO LANGUAGE  
You can select audio language during DVD playback  
(if multi languages are available).  
1 During playback, press  
1 / 8 (ANGLE)  
[MODE] repeatedly until  
1.ENG Dolby D 3/2.1ch 48k/3  
1 Press [MODE] during playback.  
ANGLE menu appears.  
2 Use [K / L] to select your desired angle.  
K
L
] to select your desired language.  
2 Use [  
/
3 Press [RETURN] to exit the menu.  
NOTES:  
• This function may not work on some DVDs with mul-  
tiple audio languages. In this case, set it on the disc  
menu. (Operation varies depending on discs. Refer to  
the manual of the disc.)  
NOTE:  
• If multiple angle function is not available, this menu  
does not appear on the screen.  
• When "NOT AVAILABLE" appears  
(
)
NOT AVAILABLE AUDIO  
on the TV screen, it means this  
function is not available on the  
disc.  
ZOOM  
The Zoom function allows you to enlarge  
the video image and to pan through the  
enlarged image.  
3 Press [RETURN] to exit the menu.  
STEREO SOUND MODE  
1 During playback, press  
OFF (ZOOM)  
You can select sound output mode.  
[MODE] repeatedly until  
ZOOM menu appears.  
STEREO (AUDIO)  
1 Press [MODE] during  
playback.  
2 Press [ENTER] repeatedly to select the required  
zoom factor.  
K
L
] to select the sound mode.  
2 Use [  
/
OFF  
ZOOM1(×1.3) ZOOM2(×2.0) ZOOM3(×4.0)  
ZOOM1 ZOOM2 ZOOM3  
• STEREO: stereo sound with left and right channels  
OFF (ZOOM)  
L-ch:  
R-ch:  
left channel sound only  
right channel sound only  
3 Press [RETURN] to exit the menu.  
K
L
s
B
] to move the zoomed picture  
3 Use [  
/
/
/
across the screen.  
SUBTITLE LANGUAGE  
You can select a language for subtitles  
during DVD playback (if available).  
4 Press [RETURN] to exit.  
• The zoomed position guide  
appears on the right corner  
of the TV screen in the zoom mode.  
1 During playback, press  
[MODE] repeatedly until  
SUBTITLE menu appears.  
1.ENG/6 (SUBTITLE)  
NOTES:  
• Zooming function does not work while disc menu is shown.  
• Zooming function is not available on some discs.  
• It may take several seconds to slide the zoomed picture.  
• The picture may be distorted if you operate other  
functions (ex. pause, fast forward etc.) repeatedly in  
the zoom mode.  
2 Use [K / L] to select your desired subtitle lan-  
guage. To cancel subtitles, select "OFF".  
3 Press [RETURN] to exit the menu.  
To cancel the zoom mode, repeat steps 1-2 and  
press [ENTER] until "OFF" appears.  
NOTES:  
• This function may not work on some DVDs with mul-  
tiple subtitle languages. In this case, set it on the disc  
menu. (Operation varies depending on discs. Refer to  
the manual of the disc.)  
• If the selected language does not have 3-letter code,  
"---" will be displayed on the screen. (Refer to  
"LANGUAGE CODE LIST" on page 35.)  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DVD SECTION  
SPECIAL PLAYBACK FUNCTIONS & SETTINGS  
BLACK LEVEL MENU  
SEARCH MENU  
You can adjust the Black Level to make the  
black parts of the picture brighter.  
You can begin playback at a specific track, title,  
chapter or from a specific point on a disc.  
1 During playback, press  
TRACK SEARCH  
OFF (BLACK LEVEL)  
[MODE] repeatedly until  
BLACK LEVEL menu  
appears.  
1 During playback, press [MODE]  
__/12 (SEARCH)  
repeatedly until SEARCH  
menu appears.  
K
L
] to select "ON" or "OFF".  
2 Use [  
/
2 Within 60 seconds, use the Number buttons to  
select the desired track number. Playback will  
start from the selected track.  
• ON: Makes the dark parts brighter.  
OFF: Shows the original picture as recorded.  
(Initial setting)  
NOTES:  
3 Press [RETURN] to exit the menu.  
• For single digit press [0] first, if the total track of the  
disc is 10 tracks or more.  
NOTE:  
• During playback or pause, you can also select tracks  
by skipping with [H / G] (or [SKIP H / G] on  
the front panel), or entering the desired track number  
with the Number buttons.  
• The setting will be saved even if the unit is turned off.  
V.S.S. (Virtual Surround System)  
You can enjoy surround-sound effect  
over two speakers on this unit.  
3 Press [RETURN] to exit the menu.  
CHAPTER SEARCH  
1 During playback, press  
OFF (V.S.S.)  
1 During playback, press  
__/21 (SEARCH)  
[MODE] repeatedly until  
[MODE] repeatedly until  
V.S.S. menu appears.  
SEARCH menu appears.  
2 Use [K / L] to select the desired sound effect.  
2 Use the Number buttons to enter the desired  
chapter number. Playback will start at the selected  
chapter.  
• 1:  
2:  
Natural effect  
Emphasized effect  
OFF: No effect (Initial setting)  
• Press [CLEAR] to erase the incorrect input.  
• For single digit press [0] first, if the total number of  
chapters of the disc is 10 or more.  
3 Press [RETURN] to exit the menu.  
NOTES:  
• When playing back 96kHz with Virtual Surround func-  
tion, the sound will be down sampled at 48kHz and  
output as digital audio.  
3 Press [RETURN] to exit the menu.  
TITLE SEARCH  
(for CD play only)  
1 During playback, press [MODE] repeatedly until  
• Virtual Surround System will be effective only when  
you set the sound mode to "STEREO". (Refer to  
"STEREO SOUND MODE" on page 25.)  
SEARCH menu appears.  
_/2 (SEARCH)  
K
L
] to display  
2 Use [  
/
TITLE SEARCH menu.  
3 Use the Number buttons to enter the desired title  
number. Playback will start at the selected title.  
• Press [CLEAR] to erase the incorrect input.  
• For single digit press [0] first, if the total number of  
titles of the disc is 10 or more.  
4 Press [RETURN] to exit the menu.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
REPEAT PLAYBACK  
TIME SEARCH  
1 During playback, press [MODE] repeatedly until  
REPEAT TRACK  
SEARCH menu appears.  
1 During playback, press  
[MODE] repeatedly until  
REPEAT menu appears.  
OFF (REPEAT)  
TOTAL  
0:0 _:_ _  
0:04:23  
K
L
] repeatedly to  
2 Use [  
/
display TIME SEARCH menu.  
2 Use [K / L] to select your desired repeat mode.  
• OFF: Repeat function off  
TRACK: Current track repeat  
ALL: All track repeat  
NOTE:  
3 Within 60 seconds, use the Number buttons to  
enter a desired disc time. Playback will start at  
the specified time.  
• Press [CLEAR] to erase the incorrect input.  
• When there is no need to enter a number, "0"  
appears automatically.  
• Repeat Track setting will be cleared when moving to  
other track.  
4 Press [RETURN] to exit.  
3 Press [RETURN] to exit the menu.  
MARKER SEARCH  
REPEAT TITLE / CHAPTER  
You can set markers to memorize your favorite  
places on a disc.  
1 During playback, press  
OFF (REPEAT)  
[MODE] repeatedly until  
1 During playback, press [MODE] repeatedly until  
REPEAT menu appears.  
SEARCH menu appears.  
2 Use [K / L] to select your desired repeat mode.  
2 Use [K / L] repeatedly to  
1
2
3
4
5
6
7
8
9
10 AC  
• OFF:  
Repeat function off  
__ __:__:__  
display MARKER SEARCH  
menu.  
CHAPTER: Current chapter repeat  
<Example: CD>  
TITLE:  
Current title repeat  
3 Use [s / B] to select a marker number among  
NOTES:  
1 to 10.  
• Repeat Title/Chapter is not available in some scenes.  
• The REPEAT setting will be cleared when moving to  
other title or chapter.  
4 When the track (or title) reaches your desired  
point, press [ENTER] to set a marker.  
3 Press [RETURN] to exit the menu.  
• The track (or title) number and  
elapsed playing time will appear  
on the TV screen.  
2
3
4
5
6
7
8
9
10  
AC  
1
00:15:30  
REPEAT A-B  
OFF (A-B REPEAT)  
A- (A-B REPEAT)  
A-B (A-B REPEAT)  
A
A
A
B
B
B
1 Press [MODE] repeatedly until  
5 You can play from the desired point by selecting  
the marker number by using [s / B] and then  
pressing [ENTER].  
A-B REPEAT menu appears.  
2 Press [ENTER] at your desired  
starting point (A).  
6 To clear a marker, select the marker number and  
press [CLEAR]. To clear all markers at once,  
select "AC" with [s / B] and press [ENTER].  
To cancel it, press [CLEAR].  
3 Press [ENTER] again at your  
desired ending point (B).  
NOTE:  
The repeat sequence begins.  
• The following operation will also erase all markers:  
– Opening the disc tray  
Turning off the power  
– Pressing [SELECT]  
4 To exit the sequence, follow step1 and press  
[ENTER] repeatedly until "OFF" appears and  
press [RETURN] to exit the menu.  
7 Press [RETURN] to exit the menu.  
NOTES:  
• The A-B repeat section can be set only within the cur-  
rent title (for DVDs) or current track (for Audio CDs).  
• A-B repeat is not available with some scenes in DVD.  
• A-B repeat playback is not available during other  
repeat playback.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DVD SECTION  
SPECIAL PLAYBACK FUNCTIONS & SETTINGS  
PROGRAMMED PLAYBACK  
You can determine the playing order of tracks.  
5 Press [STOP C] to temporarily stop the playback.  
You can resume the playback by pressing  
[PLAY B].  
1 In the stop mode, press  
Press [STOP C] twice to cancel the pro-  
grammed playback.  
PROGRAM  
CD-DA  
TOTAL 0:00:00  
[MODE].  
1
2
3
4
5
6
7
3:40  
4:30  
5:00  
3:10  
5:10  
1:30  
2:30  
• The PROGRAM screen appears.  
NOTE:  
ENTER  
1/4  
1/1  
PLAY  
1
3:40  
CLEAR  
• REPEAT setting is available during programmed  
playback. (Refer to "REPEAT TRACK" on page 27.)  
K
L
] to select a track,  
2 Use [  
/
PROGRAM  
CD-DA  
RANDOM PLAYBACK  
This function shuffles the playing order of  
tracks.  
TOTAL 0:14:25  
then press [ENTER].  
1
2
3
4
5
6
7
3:40  
1
3
3:40  
5:00  
4:30  
5:00  
3:10  
5:10  
1:30  
2:30  
10 1:30  
12 2:45  
6
1:30  
NOTES:  
• Up to 99 tracks can be entered.  
ENTER  
1/4  
1/1  
PLAY  
6
1:30  
CLEAR  
• Press [CLEAR] to erase the  
most recently entered track.  
1 In the stop mode, press  
RANDOM  
CD-DA  
TOTAL 0:45:55  
[MODE] twice.  
RANDOM PROGRAM  
no indication  
• If you enter more than 8 tracks, you can change pages  
of the program list with [H / G].  
-
-
-
-
• The RANDOM screen appears.  
PLAY  
To erase all tracks in the program at once, select "ALL  
CLEAR" at the bottom of the track list.  
2 Press [PLAY B] to start random playback.  
3 Repeat step 2 until you select all the tracks you  
want to play in the program.  
NOTE:  
• REPEAT setting is available during random playback.  
(Refer to "REPEAT TRACK" on page 27.)  
4 Press [PLAY B] to play the programmed tracks.  
3 Press [STOP C] to stop random playback.  
N-SCREEN INFORMATION  
You can check the information about the current disc by pressing [DISPLAY].  
O
For DVD-Videos  
For Audio CDs  
1 Press [DISPLAY] during playback to show cur-  
rent Chapter.  
1 Press [DISPLAY] during playback to show the  
current Track.  
4/12 0:03:21 - 0:02:15  
T
• The elapsed and remaining  
• The elapsed and remaining  
playing time of the current  
track will be displayed.  
9/49  
0:00:00 -0:03:30  
playing time of the current  
chapter will be displayed.  
2 Press [DISPLAY] again to show current Title.  
2 Press [DISPLAY] again to show current Total  
• The elapsed and remaining  
Track.  
4/12 0:13:45 - 0:45:40  
T
1/3 0:00:00 - 1:23:45  
playing time of the current title  
will be displayed.  
• The elapsed and remaining  
playing time of the total track  
will be displayed.  
PROGRAM  
B
T
L1  
3 Press [DISPLAY] again.  
• The bit rate and the current  
repeat setting will be displayed.  
When in the PROGRAM  
mode or RANDOM  
mode.  
• If you are playing a dual layered disc, the layer  
number will also be displayed.  
(L0: Layer 0 is playing. L1: Layer 1 is playing).  
3 Press [DISPLAY] again to exit.  
4 Press [DISPLAY] again to exit.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
HANGING THE DVD SET UP ITEMS  
C
You can change the DVD player’s settings by pressing [SET-UP] in DVD mode.  
The set up items are shown in the diagram below.  
Press [SET-UP] twice  
QUICK  
CUSTOM  
INITIALIZE  
AUDIO  
SUBTITLE  
LANGUAGE (p29)  
DISC MENU  
TV MODE  
STILL MODE  
TV MODE  
DISPLAY (p30)  
AUDIO (p30)  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
DOLBY DIGITAL  
PARENTAL LEVEL  
PASSWORD CHANGE  
PARENTAL (p30)  
OTHERS (p31)  
ANGLE ICON  
AUTO POWER OFF  
CUSTOM MENU  
1 In the stop mode, press  
[SET-UP] twice to display the  
DVD SETUP menu.  
SETUP  
A
LANGUAGE SETTING  
QUICK  
CUSTOM  
INITIALIZE  
SETUP  
LANGUAGE  
4 Use [K / L] to select the  
desired item, then press  
[ENTER].  
AUDIO  
SUBTITLE  
DISC MENU  
ORIGINAL  
OFF  
ENGLISH  
NOTES:  
• Pressing [SET-UP] once will  
show TV/VCR SETUP menu partly.  
K
L
SET:ENTER  
SELECT:  
/
EXIT:SETUP CANCEL:RETURN  
• AUDIO:  
Sets the audio language.  
• If the menu does not appear, press [STOP C] first.  
Make sure the unit is in DVD mode before setting.  
• SUBTITLE: Sets the subtitle language.  
• DISC MENU: Sets the language for DVD menu.  
5 Use [K / L] to select your desired language  
2 Use [K / L] to select "CUSTOM", then press  
from the list, then press [ENTER].  
[ENTER].  
SETUP  
CUSTOM  
6 Press [SET-UP] to exit the menu.  
3 Use [K / L] to select the  
desired item, then press  
[ENTER].  
LANGUAGE  
DISPLAY  
AUDIO  
PARENTAL  
OTHERS  
NOTES:  
SETUP  
LANGUAGE  
• If your desired language is not  
on the list, select "OTHER" and  
enter the code of the language.  
(Refer to "LANGUAGE CODE  
LIST" on page 35.)  
LANGUAGE CODE  
Refer to the pages below for  
continuation to set up each item.  
Please enter a 4-digit language code.  
• LANGUAGE setting: P29  
• DISPLAY setting:  
• AUDIO setting:  
PARENTAL setting: P30  
• OTHERS setting: P31  
A
B
C
D
E
P30  
P30  
• This feature may not be valid due to default setting  
of the disc. In this case, press [MODE] to select the  
language. (Refer to "AUDIO MENU" on page 25.)  
• If you select a language that is not supported by the  
disc, subtitle will be "OFF" automatically and the  
default language of the disc will be selected.  
To change the language for the on-screen menus,  
call up the TV/VCR SETUP menu by pressing  
[SET-UP] once and set the language. (Refer to "ON-  
SCREEN MENU LANGUAGE" on page 11.)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DVD SECTION  
CHANGING THE DVD SET UP ITEMS  
B
C
DISPLAY SETTING  
AUDIO SETTING  
4 Use [K / L] to select an item,  
SETUP  
DISPLAY  
Choose the appropriate Audio settings for your  
equipment as it only affects during the playback of  
DVD discs.  
then press [ENTER].  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
QUICK  
• TV MODE:  
K
L
] to select an item,  
4 Use [  
/
SETUP  
AUDIO  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
then press [ENTER] repeated-  
ly until your desired setting  
appears.  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
• 4:3 LETTER BOX (default):  
To show black bars on top and  
bottom of the screen.  
• 4:3 PAN & SCAN:  
To show a full height picture with both sides  
trimmed.  
SETUP  
DISPLAY  
TV MODE  
4:3 LETTER BOX  
4:3 PAN & SCAN  
• DRC (Dynamic Range Control):  
• ON : To compress the range of soft to loud sound.  
(default)  
• OFF : Output the original sound.  
NOTE:  
• DOWN SAMPLING:  
• ON : Output in 48kHz. (default)  
• OFF : Output the original sound.  
You can access this setting directly by selecting  
"QUICK" at step 2 on page 29.  
• STILL MODE:  
This function allows you to adjust picture resolution  
and quality in the still mode.  
NOTE:  
• When playing a disc with copyright protection, the  
sound will be output at 48kHz even if the setting is  
"OFF".  
SETUP  
DISPLAY  
STILL MODE  
AUTO  
FIELD  
FRAME  
• AUTO (default):  
Automatically select the best  
QUICK  
• DOLBY DIGITAL:  
• BITSTREAM: Output a Dolby Digital signal.  
(default)  
resolution setting (FRAME or FIELD) based on  
the data characteristics of the pictures.  
• FIELD:  
Select "FIELD" when the pictures are still unstable  
even if "AUTO" is selected. FIELD stabilizes the  
pictures, although the picture quality may become  
coarse due to the limited amount of data.  
• FRAME:  
Select "FRAME" to display relatively motionless  
pictures in higher resolution. FRAME improves  
the picture quality, although it may unstabilize the  
pictures due to simultaneous output of two field  
data.  
• PCM:  
Convert the Dolby Digital to PCM.  
(2 channel stereo)  
NOTES:  
You can access this setting directly by selecting  
"QUICK" at step 2 on page 29.  
• Set to "BITSTREAM" when the unit is connected to  
a Dolby Digital Decoder.  
5 Press [SET-UP] to exit the menu.  
5 Press [SET-UP] to exit the menu.  
D
PARENTAL SETTING  
This feature allows you to set the rating level of your  
DVD discs. Playback will stop if the disc ratings  
exceed the level you set.  
PARENTAL LEVEL  
4 Enter four-digit password with  
SETUP  
PARENTAL  
PASSWORD  
the Number buttons, then  
Please enter a 4-digit password.  
press [ENTER].  
NOTE:  
• Enter any 4 digits (except for 4737) to set the pass-  
word for the first time, and record it for your memory.  
5 Use [K / L] to select  
SETUP  
PARENTAL  
"PARENTAL LEVEL", then  
PARENTAL LEVEL  
PASSWORD CHANGE  
ALL  
press [ENTER].  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
E
OTHERS SETTING  
SETUP  
PARENTAL  
6 Use [K / L] to select the  
desired level, then press  
[ENTER].  
PARENTAL LEVEL  
K
L
] to select an item,  
4 Use [  
/
SETUP  
OTHERS  
ALL  
8 [ADULT]  
7 [NC-17]  
6 [R]  
ANGLE ICON  
AUTO POWER OFF  
ON  
ON  
then press [ENTER] repeated-  
ly to set the feature "ON" or  
"OFF".  
7 Press [SET-UP] to exit the menu.  
• ANGLE ICON:  
CONTROL LEVELS  
• ON: To show the angle icon when multiple  
camera angles are available during DVD  
playback. (default)  
ALL: All parental locks are canceled.  
8 [ADULT]: DVD software of any grade  
(adult/general/children) can be played back.  
• OFF: To keep angle icon from the display.  
7 to 2: Only DVD software intended for general  
use and children can be played back.  
• AUTO POWER OFF:  
• ON: To activate screen saver program and turn  
off the unit automatically. (default)  
1 [KID SAFE]: Only DVD software intended for  
children can be played back, with those intended  
for adult and general use prohibited.  
• OFF: To deactivate Auto Power Off function.  
NOTE:  
• The screen saver program starts when there is no  
input from the unit for 5 minutes in the stop mode.  
After the screen saver program is activated for 15  
minutes, the power is automatically turned off.  
NOTE:  
• With some DVDs, it may be difficult to find if they are  
compatible with parental lock. Be sure to check if the  
parental lock function operates in the way that you  
have set.  
5 Press [SET-UP] to exit the menu.  
PASSWORD CHANGE  
SETUP  
PARENTAL  
4 Enter current password with  
the Number buttons, then  
press [ENTER].  
PASSWORD  
Enter current password.  
INITIALIZE  
This allows you to return all items of  
SETUP  
PARENTAL  
5 Use [K / L] to select  
"PASSWORD CHANGE", then  
press [ENTER].  
PARENTAL LEVEL  
PASSWORD CHANGE  
ALL  
SETUP menu (except for PARENTAL  
setting and menu language) to their default settings.  
SETUP  
PASSWORD  
Please enter a 4-digit password.  
PARENTAL  
6 Enter four-digit password with  
the Number buttons, then  
press [ENTER].  
1 In the stop mode, press [SET-UP] twice to  
display the DVD SETUP menu.  
1
2
3
4
Don't forget the password.  
Press 'ENTER' to activate password.  
SETUP  
2 Use [K / L] to select  
QUICK  
"INITIALIZE", then press  
CUSTOM  
7 Press [SET-UP] to exit the menu.  
INITIALIZE  
[ENTER].  
NOTE:  
• If you forget the current password, enter 4737 first,  
then enter your new password.  
The former password will be cleared and parental  
level will be set to "ALL" (default).  
3 Use [K / L] to select "YES",  
SETUP  
INITIALIZE  
then press [ENTER] twice.  
To cancel the initialization,  
select "NO".  
Initialize?  
NO  
YES  
4 Press [SET-UP] to exit the menu.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ROUBLESHOOTING GUIDE  
T
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the following  
guide for the possible remedy of a problem before contacting the Customer Service. Sometimes a perfor-  
mance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. It  
could save your time and money.  
SYMPTOM  
No power  
POSSIBLE REMEDY  
Make sure the power plug is connected to an AC outlet.  
(In case of power failure) Check the breaker.  
PAGE  
9
--  
No operation by remote control  
7
Check if the batteries are weak or inserted incorrectly.  
Replace weak batteries and insert with their polarities (+/-  
signs) as indicated.  
--  
Aim the remote control at the remote sensor and operate  
within 23 feet (7m) of the unit.  
--  
34  
9
Remove all obstacles to clear the path of the infrared signal.  
Refer to the infrared signal.  
Select the correct mode to operate by pressing [SELECT].  
The operable range from the unit is 10 feet (3m) within 15˚.  
--  
Poor or no picture  
6
--  
--  
9
13  
--  
9
Check if antenna or cable is connected properly.  
Check for the broken pin or wire of antenna cable.  
Check for source of reception disturbance.  
Press [SELECT] to select the correct mode.  
Perform channel scanning to memorize available TV channels.  
Try another channel. If OK, then possible station problem.  
Adjust picture control (COLOR/CONTRAST/BRIGHT etc.).  
Check for magnetism from nearby appliances and try  
degaussing.  
--  
Poor or no picture in playback  
Poor or no sound  
15  
34  
--  
Adjust tracking control.  
Try video head cleaning.  
The videotape may be old or worn. Replace with new one.  
X
Y
].  
--  
--  
15  
Adjust volume control using [VOL.  
Try another channel. If OK, then possible station problem.  
Check if the unit is in Still mode or Slow motion playback.  
If so, press [PLAY B] to return to normal playback.  
/
Cannot go into recording mode  
15  
Make sure the cassette has an erase-prevention tab. If neces-  
sary, cover the hole with plastic tape.  
Timer recording does not work  
or results in failure  
19  
19  
10  
--  
Make sure the begin/end time is set correctly.  
Make sure the power is off to activate timer recording.  
Check if the unit’s clock is set to current time and date.  
The program may contain copy protection signals that restricts  
copying.  
20  
--  
--  
The timer setting overlapped with another setting has priority.  
Check if the tape reached the end during recording.  
Check if the power failure during recording.  
Picture or color fades in and out  
when copying a videotape  
21  
You cannot copy a copyrighted videotape. You are experienc-  
ing copy guard protection.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
SYMPTOM  
Misspelling in captions  
POSSIBLE REMEDY  
PAGE  
Error committed by the closed captioning production company.  
--  
Possible in a live broadcast. Not in case of a prerecorded pro- --  
gram.  
Text is not shown in its entirety  
or a delay occurs from what is  
being said  
A few seconds of delay is common for live broadcast.  
If a dialogue exceeds the display capacity (220 words per  
minute), selective editing is used so that the captions remain  
up-to-date with the current TV screen dialogue.  
--  
Captions scrambled with white  
boxes  
Caused by interferences of building, power lines, thunder-  
storms, etc.  
--  
No captions in a program which The broadcast may use a time compression process to speed --  
must contain closed caption  
up the program. The decoder cannot read the compressed  
information and captions will be lost.  
No captions in a pre-recorded  
videotape with indicated closed  
captions included  
Possibility of a illegal copy or an erroneous copying process  
accidentally performed by the fabricator.  
--  
Black box in the TV screen  
No picture  
You are in TEXT mode. Select CAPTION mode or "OFF"  
11  
22  
This unit cannot play DVD-RAM/CD-i/Photo CD/Video  
CD/DVD with region codes other than "1" and "ALL".  
Disc cannot be played  
No sound  
Clean the disc.  
Place the disc correctly, with the label side up.  
Cancel the parental setting or change the control level.  
34  
23  
30  
Correct the audio output settings.  
Confirm the power and audio settings of external audio com-  
ponent.  
30  
--  
No DTS audio is output  
Distorted picture  
This unit does not support DTS audio. This is not a malfunc-  
tion.  
--  
During the playback of a 2-layered disc, pictures may stop for --  
a moment. This happens while the 1st layer is being switched  
to the 2nd layer. This is not a malfunction.  
This happens right after fast forwarding or rewinding.  
--  
Audio or subtitle language does The selected language is not available for audio or subtitle on  
29  
not match the setting  
the DVD.  
The camera angle cannot be  
changed  
The DVD does not contain sequences recorded from different  
camera angles.  
25  
29  
23  
--  
Audio or subtitle language can-  
not be changed  
The DVD does not contain audio source or subtitles in the  
selected language.  
"Prohibited icon" appears on the That operation is not available by the unit or the disc.  
screen  
CD/DVD sound dropout  
No CD/DVD reproduction  
DVD picture poor  
Scratched disc. Replace with an unscratched one.  
NOTES:  
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s  
Manual for details on correct operations.  
• Playback from a desired track and random playback are not available during playback.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
AINTENANCE  
M
DEGAUSSING  
CABINET CLEANING  
A degaussing circuit in this unit clears up color  
errors on the TV screen. Color errors occur when  
there is any excess magnetism close to the unit.  
This circuit is designed to operate once when the  
unit is first plugged in. If you see minor color  
errors on the screen, unplug the unit for approx-  
imately 30 minutes. When you plug the unit again,  
the degaussing circuit will operate to clear errors.  
Take this step any time the TV screen is accidental-  
ly magnetized or when you move the unit.  
• Wipe the front panel and other exterior surfaces of  
the unit with a soft cloth immersed in lukewarm  
water and wrung dry.  
• Never use a solvent or alcohol. Do not spray  
insecticide liquid near the unit. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
SERVICING  
• Should your unit become inoperative, do not try to  
correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord and please call our help line men-  
tioned on the front page, to locate an Authorized  
Service Center.  
AUTO HEAD CLEANING  
• Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clearer pic-  
ture.  
• Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long peri-  
ods of use or the usage of rental or worn tapes  
can cause this problem.  
If a streaky or snowy picture appears during play-  
back, the video heads in your unit may need to be  
cleaned.  
IR SIGNAL CHECK  
Use the AM radio or the digital camera to check if  
the remote control properly sends out the infrared  
signal. It will help to define the cause of malfunction.  
Using AM radio  
1. Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
Tune the AM radio to no broadcasting band.  
Press any button on remote control toward  
the radio. If the radio receives the signal  
from remote control properly, the sound will  
flutter.  
2. If a Video Head Cleaner does not solve the prob-  
lem, please call our help line mentioned on the  
front page, to locate an Authorized Service  
Center.  
Using digital camera  
(including built-in camera of cellular  
NOTES:  
phone)  
• Press and hold any button on remote control  
toward a digital camera. The remote control is  
working if you confirm infrared light through the  
digital camera.  
• Remember to read the instructions included with the  
video head cleaner before use.  
• Clean video heads only when problems occur.  
IF THE LASER OPTICAL PICKUP UNIT IS  
DIRTY  
DISC HANDLING  
• Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
• If the unit still does not perform properly when it is  
operated, while referring to the relevant sections  
and to “TROUBLESHOOTING GUIDE” in this  
Owner’s Manual, the laser optical pickup unit may  
be dirty. Consult your dealer or an Authorized  
Service Center for inspection and cleaning of the  
laser optical pickup unit.  
• Always store the disc in its protective case when it  
is not used.  
To clean-off, use a soft cloth.  
• Do not use a hard cloth since this  
will mar the disc.  
• Wipe the disc in a straight line from center to edge.  
• Never wipe with a circular motion.  
• Do not use detergent or abrasive clean-  
ing agents.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PPENDIX  
A
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
TV Display  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
31  
32  
33  
34  
35  
36  
CATV channel  
TV Display  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
W+55 W+56 W+57 W+58  
91 92 93 94  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
CATV channel W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
LANGUAGE CODE LIST  
Language  
Code Language  
German [GER]  
Code  
Language  
Code Language  
Code  
A-B  
5051  
5158  
5758  
5360  
5367  
5447  
5569  
5455  
5467  
Mongolian  
Nauru  
Nepali  
5960  
6047  
6051  
Somali  
6561  
5165  
6567  
6569  
6568  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
Breton  
Bulgarian  
Burmese  
Byelorussian  
C-E  
Cambodian  
Catalan  
Chinese [CHI]  
Corsican  
Croatian  
Czech [CZE]  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
F-H  
4748  
4747  
4752  
6563  
4759  
4764  
5471  
4765  
4771  
4772  
4847  
5167  
4860  
5072  
4854  
4855  
4864  
4853  
5971  
4851  
Greek [GRE]  
Greenlandic  
Guarani  
Gujarati  
Hausa  
Spanish [SPA]  
Sundanese  
Swahili  
Norwegian [NOR] 6061  
O-R  
Swedish [SWE]  
T
Tagalog  
Tajik  
Tamil  
Tatar  
Telugu  
Thai  
Occitan  
Oriya  
Oromo(Afan)  
Panjabi  
Pashto;Pushto  
Persian  
Polish [POL]  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
Hebrew  
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
5565  
5560  
5547  
5551  
5557  
5347  
5566  
5647  
5669  
5760  
5765  
5757  
6469  
5771  
6460  
5761  
5767  
Portuguese [POR] 6266  
Tibetan  
Tigrinya  
Tonga  
Tsonga  
Turkish [TUR]  
Turkmen  
Twi  
Quechua  
6367  
Rhaeto-Romance 6459  
Irish [IRI]  
Romanian [RUM]  
Russian [RUS]  
S
Samoan  
Sangho  
Sanskrit  
Scots Gaelic  
Serbian  
Serbo-Croatian  
Sesotho  
Setswana  
Shona  
Sindhi  
6461  
6467  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
U-Z  
Kashmiri  
Kazakh  
Ukrainian  
Urdu  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
5759  
4947  
7254  
4961  
5464  
4965  
5047  
6058  
5160  
5161  
5166  
Kinyarwanda  
Kirghiz  
Kirundi  
Korean [KOR]  
Kurdish  
L-N  
Laothian  
Latin  
Latvian;Lettish  
Lingala  
Lithuanian  
Macedonian  
Malagasy  
Malay  
Malayalam  
Maltese  
Maori  
Uzbek  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
Yoruba  
Zulu  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
Singhalese  
Siswat  
Slovak  
Slovenian  
Faroese  
Fiji  
Finnish [FIN]  
French [FRE]  
Frisian  
Galician  
Georgian  
5261  
5256  
5255  
5264  
5271  
5358  
5747  
If you choose a language that has a 3 letter language  
code, the code will be displayed every time you change  
the AUDIO or SUBTITLE language setting. If you  
choose any other languages, '---' will be displayed  
instead. (3 letter language code is written in bracket.)  
Marathi  
Moldavian  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PECIFICATIONS  
S
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV/VCR  
CRT:  
20 inch in-line gun,  
90˚ deflection tube  
NTSC-M  
§15.119/FCC  
Rotary four-head  
1/2 inch  
OTHER SPECIFICATIONS  
Television system:  
Closed caption system:  
Video Heads:  
Terminals  
Antenna input:  
VHF/UHF/CATV  
75 ohm unbalanced  
(F-type)  
Tape width:  
Tape speed  
SP:  
Video input:  
RCA connector × 1  
RCA connector × 2  
1/8" stereo (3.5 mm)  
33.40 mm/sec.  
16.67 mm/sec.  
11.12 mm/sec.  
Audio L/R input:  
Headphone:  
Coaxial digital  
audio output:  
LP:  
SLP:  
Tuner channel  
TV VHF Low:  
TV VHF High:  
TV UHF:  
One pin jack,  
500 m Vpp (75 ohm)  
Digital encoded  
infrared light system  
5°C to 40°C  
(41°F~104°F)  
AC 120 V, 60 Hz  
90 W  
#2~#6  
#7~#13  
#14~#69  
Remote control:  
CATV  
VHF:  
MID band:  
SUPER band:  
HYPER band:  
Operating temperature:  
Power requirements:  
Power consumption  
(Maximum):  
5A  
A5~A1, A~I  
J~W  
W+1~W+84  
Picture tube:  
Dimensions:  
20"  
H: 20-3/16" (513 mm)  
DVD  
Product type:  
Discs:  
W: 22-1/8" (562 mm)  
DVD Player  
DVD video, Audio CD  
NTSC color  
D: 19-7/8" (505 mm)  
51.1 lbs. (23.2 kg)  
Weight:  
Output signal format:  
• Designs and specifications are subject to change without notice.  
• If there is a discrepancy between languages, the default language will be English.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
NDICE DE CONTENIDO  
Í
PREPARATIVOS PARA EL USO . . . . . . . . . . . .37  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . .37  
CONEXIÓN A UN DISPOSITIVO EXTERNO  
REPRODUCCIÓN . . . . . . . . . . . . . . . . . . . . . . .41  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . .41  
GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . .41  
GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . .41  
GRABACIÓN CON TEMPORIZADOR  
(FRONTAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . .38  
CONEXIÓN A UN DISPOSITIVO DE AUDIO DIGITAL  
(TRASERA) . . . . . . . . . . . . . . . . . . . . . . . . . . . .38  
AUTOMÁTICO . . . . . . . . . . . . . . . . . . . . . . . . . .42  
SECCIÓN TV/VCR  
SECCIÓN DVD  
FUNCIONAMIENTO Y AJUSTES DEL  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . .43  
MENÚ DE DISCO/MENÚ DE TÍTULO . . . . . . . . . .43  
TELEVISOR . . . . . . . . . . . . . . . . . . . . . . . . . . .39  
PARA VER UN PROGRAMA DE TELEVISIÓN . . . .39  
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . .39  
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . .40  
IDIOMA DE MENÚ DE PANTALLA . . . . . . . . . . . . .40  
REPARATIVOS PARA EL USO  
P
CONEXIONES DE ANTENA/CABLE  
Enchufe el cable entrante en la toma ANT., en la parte trasera de la unidad.  
Si su servicio de cable le suministra una caja convertidora o si usted utiliza un sistema de satélite, conecte  
la caja con esta unidad, como se indica a continuación.  
Antena  
Cable  
Señal de TV  
o
ANT.  
AUDIO OUT  
COAXIAL  
Parte trasera de la  
unidad  
Cable entrante desde antena  
casera/empresa de cable (sin  
caja de cable)  
ANT.  
Caja de cable o caja de satélite*  
O
T
U
O
IN  
*NOTA  
(NO DESCONECTAR DE LA CAJA)  
Algunos sistemas de TV por cable utilizan  
señales cifradas y requieren un convertidor  
especial para recibir estos canales.  
Cable entrante desde empresa de cable  
o antena de satélite  
Consulte con su empresa de cable local.  
NOTA:  
Para su seguridad y  
Patilla doblada  
Antes de enchufar la antena en la  
toma ANT. de la unidad, compruebe  
que la patilla no está doblada. Si  
está doblada, enderece la patilla  
como se indica en la ilustración y  
enchufe la patilla a la toma ANT. de  
la unidad.  
para evitar daños en la  
unidad, desenchufe el  
cable de la antena de la  
toma ANT. antes de  
mover la unidad.  
Cable  
Enchufe  
(Debe ser  
enderezada)  
(Patilla recta)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
PREPARATIVOS PARA EL USO  
CONEXIÓN A UN DISPOSITIVO EXTERNO (FRONTAL)  
Cuando vea un programa grabado en otra fuente (videograbadora o videocámara), utilice  
las tomas de entrada AUDIO/VIDEO en la parte frontal de la unidad.  
Conecte las tomas de salida de Audio/Vídeo de otra fuente a las tomas AUDIO L/R y  
VIDEO de esta unidad.  
AUX  
A continuación, utilice [SELECT] o [CH.  
K
/
L
] hasta que aparezca "AUX" en la pantalla.  
OPEN/  
CLOSE  
STOP/  
EJECT  
POWER  
PLAY  
SELECT  
PLAY  
VOLUME  
SKIP  
SKIP  
STOP  
CHANNEL  
REC/OTR  
REW  
F.FWD  
HEADPHONE  
VIDEO  
L
-
AUDIO  
-
R
E
SEARCH  
D
DVD  
TV/VCR  
Por ejemplo,  
videograbadora o  
videocámara, etc.  
Parte frontal de  
la unidad  
A las tomas de salida de audio  
(ENTRADA)  
Cable de audio  
(SALIDA)  
HEADPHONE  
VIDEO  
L
AUDIO  
R
(disponible en el mercado)  
A la toma de salida de vídeo  
(ENTRADA)  
Cable de vídeo (disponible en el mercado)  
(SALIDA)  
NOTA:  
Cuando conecte una videograbadora monoaural (otra fuente) a esta unidad, conecte la toma de salida de audio de la  
videograbadora monoaural (otra fuente) a la toma AUDIO L de esta unidad. El sonido saldrá igualmente por ambos  
canales L y R (izquierdo y derecho).  
CONEXIÓN A UN DISPOSITIVO DE AUDIO DIGITAL (TRASERA)  
Puede conectar esta unidad a un dispositivo de audio digital para disfrutar del sonido digital de DVD.  
Conecte a un amplificador equipado con tomas de entrada digital, tales como una platina MD o DAT. Para  
reproducir un disco DVD en un formato ambiental multicanal Dolby Digital en esta unidad, conéctela a un  
decodificador Dolby Digital.  
Utilice un cable coaxial digital de audio (disponible en el mercado) para las conexiones de audio.  
AUDIO OUT  
COAXIAL  
AUDIO OUT  
COAXIAL  
A la toma AUDIO  
(SALIDA)  
OUT COAXIAL  
(Solamente DVD  
AUDIO OUT)  
Decodificador  
Dolby Digital  
A la toma de entrada de  
audio coaxial digital  
o
(ENTRADA)  
Cable de audio coaxial digital  
(disponible en el mercado)  
Platina MD, plati-  
na DAT, etc.  
A la toma de entrada de  
audio coaxial digital  
(ENTRADA)  
NOTAS:  
• La fuente de audio de un disco en formato ambiental multicanal Dolby Digital no puede ser grabado como sonido digital  
por una platina MD o DAT.  
• Asegúrese de apagar todos los dispositivos del sistema antes de conectar otro dispositivo.  
• Consulte los manuales del usuario de los dispositivos que van a conectarse a la unidad.  
• Para conectar a una platina MD o DAT, ajuste "DOLBY DIGITAL" en "PCM" para la salida de audio en el modo de  
ajuste, y para conectar a un decodificador Dolby Digital, ajuste en "BITSTREAM" (consulte "AUDIO SETTING en pági-  
na 30). Utilizar una unidad con unos ajustes incorrectos puede generar distorsión de ruido y puede asimismo dañar los  
altavoces.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
SECCIÓN TV/VCR  
UNCIONAMIENTO Y AJUSTES DEL TELEVISOR  
F
PARA VER UN PROGRAMA DE TELEVISIÓN  
AJUSTE DEL RELOJ  
TV/VCR  
TV/VCR  
Ajuste correctamente el reloj de la  
unidad para grabación con temporizador  
1 Después de finalizar la conexión de la  
antena o del cable, conecte el cable de  
alimentación a una toma estándar de  
CA.  
para videograbadora. Se sugiere ajustar el reloj  
manualmente cuando se configure por primera vez  
la unidad, y luego fijar el ajuste automático del reloj  
en "ON" para corregir la hora periódicamente.  
2 Presione [POWER] para encender la unidad.  
K
L
] o los botones numéricos  
3 Utilice [CH.  
/
NOTA:  
• Si no pude recibir una emisora con las señales  
horarias, el ajuste automático del reloj no estará  
disponible. Utilice únicamente el ajuste manual.  
para seleccionar el número de canal deseado.  
Para utilizar los botones numéricos  
•Canales de un dígito: (Ej.: 02, 03, 04, etc.)  
Presione primero [0] para seleccionar un canal de un dígito.  
AJUSTE MANUAL DEL RELOJ  
•Canales de dos dígitos: (Ej.: 12, 38, 95 ...)  
Presione dos dígitos directamente.  
En el siguiente ejemplo, el reloj está ajustado en:  
•Canales de tres dígitos: (Ej. 115, 125 ...)  
Presione primero [+100], y luego presione los últimos  
dos dígitos.  
FECHA:  
5 de mayo de 2006  
5:40PM  
HORA DE AJUSTE:  
- TV/VCR PREP. -  
COMO PROGRAMAR  
AJUSTE RELOJ  
AJUSTE DE CANAL  
AJUSTE DE USER  
AJUSTE DE V-CHIP  
ANGUAGE [ENGLISH]  
1 Presione [SET-UP].  
Utilice [K / L] para ir hasta  
"AJUSTE RELOJ", y presione  
[ENTER].  
B
4 Utilice [VOL. X / Y] para ajustar el volumen.  
Presione [MUTE] para  
VOLUMEN 20  
silenciar al instante el sonido.  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Presione de nuevo para  
restaurar el nivel de sonido  
anterior.  
– AJUSTE RELOJ –  
2 Utilice [K / L] para ir hasta  
"AJUSTE MANUAL RELOJ", y  
presione [ENTER].  
RELOJ AUT.  
[ON]  
BUSQ. AUTO RELOJ CA.  
CAN. RELOJ AUT.  
[ 02 ]  
B
AJUSTE MANUAL RELOJ  
• Si no hay ninguna emisora local  
PBS en su zona o en su sistema  
de cable, seleccione "RELOJ AUT." y presione  
[ENTER] para desactivar la función antes de este  
paso.  
NOTA:  
HORA VER.  
[OFF]  
• Incluso aunque apague la unidad en el modo DVD,  
la unidad estará en el modo TV/VCR cuando vuelva  
a encenderse.  
PARA VER UN CANAL DE CABLE O SATÉLITE  
– AJUSTE MANUAL RELOJ –  
3 Utilice [K / L] para ajustar los  
Si la unidad está conectada a una caja de cable o de  
satélite, utilice [CH. K / L] para seleccionar CA3 o  
CA4 según el ajuste de canal de salida del dispositivo  
y seleccionar el canal deseado en dicho dispositivo.  
datos deseados de mes, día,  
año, hora y minuto.  
MES  
0 5  
DIA  
AÑO  
/
:
0 5 VIE  
2 0 0 6  
HORA  
0 5  
MINUTO  
4 0 PM  
Utilice [s / B] para pasar a  
otro elemento.  
PARA VER UNA ENTRADA EXTERNA  
4 Presione [SET-UP].  
Cuando un equipo externo esté  
AUX  
5:40 PM  
Aunque los segundos no se  
muestran, se comienzan a  
contar desde 00 cuando se  
presiona [SET-UP]. Utilice esta función para  
sincronizar el reloj con la hora correcta.  
conectado a las tomas de entrada  
frontales AUDIO/VIDEO, presione  
[SELECT] o [CH. K / L]  
repetidamente hasta que  
aparezca "AUX" en la pantalla.  
NOTA:  
NOTA:  
• Cuando desenchufe el cable de CA o si hay un corte  
del suministro eléctrico durante más de 3 segundos,  
es posible que tenga que reajustar el reloj.  
• Si no hay entrada de señal del terminal de antena ni  
se hace funcionar durante 15 minutos, el TV se apa-  
gará automáticamente.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
SECCIÓN TV  
FUNCIONAMIENTO Y AJUSTES DEL TELEVISOR  
AJUSTE DE CANAL  
IDIOMA DE MENÚ DE PANTALLA  
TV/VCR  
TV/VCR  
Es necesario preseleccionar el canal al  
principio o en caso de haber movido el  
televisor a una zona distinta.  
Puede seleccionar el idioma del menú  
de pantalla entre inglés, español y  
francés.  
- TV/VCR PREP. -  
COMO PROGRAMAR  
AJUSTE RELOJ  
1 Presione [SET-UP].  
AUTOPROGRAMACIÓN DEL CANAL  
Utilice [K / L] para ir hasta  
AJUSTE DE CANAL  
AJUSTE DE USER  
AJUSTE DE V-CHIP  
IDIOMA [ESPAÑOL]  
TÍTULO [OFF]  
1 Presione [SET-UP].  
- TV/VCR PREP. -  
COMO PROGRAMAR  
AJUSTE RELOJ  
AJUSTE DE CANAL  
AJUSTE DE USER  
AJUSTE DE V-CHIP  
IDIOMA [ESPAÑOL]  
TÍTULO [OFF]  
"IDIOMA".  
B
Utilice [K / L] para ir hasta  
B
ZERO RETURN  
"AJUSTE DE CANAL", y  
presione [ENTER].  
ZERO RETURN  
2 Presione [ENTER] repetidamente para  
seleccionar "ENGLISH", "ESPAÑOL" o  
"FRANÇAIS".  
2 Utilice [K / L] para ir hasta  
"AUTOPROGRAMACIÓN DE  
CA.", y presione [ENTER].  
– AJUSTE DE CANAL –  
AGREGAR / BORRAR (CATV)  
AUTOPROGRAMACIÓN DE CA.  
B
3 Presione [SET-UP] para salir del menú.  
El sintonizador explora y memoriza todos los  
canales activos de su zona.  
NOTAS:  
• Esta función afecta solamente al idioma del menú de  
pantalla y no a la fuente de sonido.  
3 Cuando la exploración ha  
finalizado, se muestra el canal  
memorizado más bajo.  
CA 15  
• Si por alguna razón el menú ya está en inglés o en  
francés, presione [SET-UP] y mediante [K / L] vaya  
a "LANGUAGE [ENGLISH]" o "LANGAGE  
[FRANÇAIS]", y presione [ENTER] repetidamente  
para seleccionar el idioma deseado, y presione  
[SET-UP].  
<EJEMPLO>  
Si en la pantalla del televisor  
aparece "NO HAY SEÑAL DE  
TV", compruebe la conexión  
de la antena y vuelva a  
intentar.  
NO HAY SEÑAL DE TV  
NOTAS:  
• La unidad puede reconocer canales de CATV como  
canales de TV si el estado de la recepción es  
deficiente. En tal caso, compruebe la conexión de la  
antena y vuelva a intentar "AUTOPROGRAMACIÓN  
DE CA.".  
La autoprogramación del canal NO es necesaria  
cuando está conectado a una caja de cable o de  
satélite. Simplemente seleccione el canal para  
entrada de caja de cable o de satélite (ej. CA 3 o  
CA 4) en la unidad, y seleccione el canal desea-  
do en la caja de cable o de satélite.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
EPRODUCCIÓN  
RABACIÓN  
R
G
NOTAS:  
REPRODUCCIÓN BÁSICA  
• Inserte una cinta de casete con la lengüeta de protec-  
ción contra borrado sin quitar.  
TV/VCR  
1 Inserte una cinta pregrabada para  
encender la unidad  
• Esta unidad no puede grabar el contenido del DVD  
incorporado.  
• SOLAMENTE podrá ver el mismo programa de tele-  
visión que se esté grabando.  
automáticamente (Auto Power  
On/Actividad automática).  
2 Seleccione el modo TV/VCR presionando  
[SELECT].  
GRABACIÓN NORMAL  
NOTA:  
TV/VCR  
CA 10  
1 Utilice [CH. K / L] o los  
botones numéricos para  
seleccionar el canal donde se  
va a grabar.  
Si se ha quitado la lengüeta de protección contra bor-  
rado, la unidad cambiará en el modo VCR y empezará  
la reproducción automáticamente.  
B
REPRODUCIR  
3 Para iniciar la reproducción,  
presione [PLAY B].  
NOTA:  
• Si la unidad está conectada a una caja de cable o  
de satélite, deberá estar en CA3 o CA4. Seleccione  
en la caja de cable o de satélite el canal donde se  
va a grabar.  
NOTA:  
Incluso en el modo DVD, puede iniciar la reproducción  
en videograbadora si presiona [PLAY  
frontal (del lateral de TV/VCR).  
B
] en el panel  
PARAR  
4
5
Para interrumpir la reproducción,  
2 Presione [SPEED] para selec-  
presione [STOP  
C
].  
cionar la velocidad de cinta  
SP  
deseada (SP/SLP). (Consulte  
"SELECTING TAPE SPEEDS"  
en página 15.)  
E
D
Para rebobinar la cinta, presione  
[REV ].  
Para hacer avanzar la cinta, pre-  
sione [FWD ].  
Para interrumpir el movimiento de  
la cinta, presione [STOP ].  
REBOBINAR  
AV RAPIDO  
E
D
3 Presione [REC] para iniciar la  
GRABAR  
grabación.  
C
A
EXPULSAR  
6
Para expulsar la cinta de la unidad,  
presione [STOP/EJECT C /A] en  
el panel frontal.  
SP  
4 Presione [PAUSE F] para  
AJUSTE DE SEGUIMIENTO  
PAUSA  
interrumpir temporalmente la  
El ajuste de seguimiento se establecerá automáticamente  
al iniciar la reproducción (función de seguimiento digital).  
Si aparecen líneas de ruido (rayas negras y blancas) en la ima-  
grabación de escenas no  
deseadas.  
Presione [PAUSE F] de  
nuevo o [REC] para reanudar  
la grabación.  
gen de reproducción, utilice [CH.  
K
/
L
] hasta que las rayas  
SP  
desaparezcan (ajuste de seguimiento manual). Esto también  
está disponible en el modo Pausa/Imagen fija/Cámara lenta.  
Para desactivar el modo de seguimiento manual, pare  
la cinta una vez e inicie de nuevo la reproducción.  
NOTA:  
• Si la grabación se mantiene en pausa durante más  
de 5 minutos, la unidad pasará automáticamente al  
modo de grabación para que la cinta no sufra daños.  
IMAGEN FIJA  
• Durante la reproducción, presione [PAUSE F]  
para congelar la imagen.  
Puede avanzar la imagen fotograma a fotograma  
presionando repetidamente [PAUSE F].  
5 Presione [STOP C] para interrumpir la  
grabación.  
Para desactivar el modo de imagen fija, presione [PLAY  
B
].  
CÁMARA LENTA  
• Durante la reproducción, presione [PAUSE F] y, a  
continuación presione [FWDD ].  
Para desactivar el modo de cámara lenta, presione [PLAY  
B
].  
NOTA:  
Si la unidad se mantiene en el modo cámara lenta o imagen fija durante  
más de 5 minutos, entrará automáticamente en el modo de parada.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
SECCIÓN TV/VCR  
GRABACIÓN  
GRABACIÓN CON TEMPORIZADOR AUTOMÁTICO  
– COMO PROGRAMAR –  
CA FECHA INICIO FINAL  
61 7/03 LUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
K
L
] para ajustar la hora  
5
6
Utilice [  
y el minuto de inicio/fin deseados.  
Presione [ ] para pasar al  
siguiente elemento.  
/
M
8:50PM- -  
-:- - - -  
-:- - - -  
TV/VCR  
Puede ajustar ocho programas para grabar en  
días concretos, diariamente o semanalmente,  
dentro de un periodo de un año.  
B
B
En el siguiente ejemplo, el temporizador está  
ajustado para grabar:  
– COMO PROGRAMAR –  
CA FECHA INICIO FINAL  
61 7/03 LUN 7:30P 8:50P  
SP  
Utilice [  
K
/
L
] hasta que aparezca la  
velocidad de cinta deseada.  
(Consulte "SELECTING TAPE SPEEDS"  
en página 15.)  
M
M
B
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
FECHA:  
3 de julio de 2006  
de7:30PM a 8:50PM  
CA61  
HORA DE AJUSTE:  
CANAL:  
7 Presione [ENTER] para finalizar el ajuste.  
VELOCIDAD DE CINTA: SP  
Para ajustar otro programa, repita los pasos 2 a 7.  
• Para corregir el programa durante el ajuste,  
presione [s] para retroceder un paso y utilice  
[K / L] para introducir los números correctos.  
• Presione [SET-UP] para salir del menú.  
- TV/VCR PREP. -  
1 Presione [SET-UP].  
B
COMO PROGRAMAR  
AJUSTE RELOJ  
Utilice [K / L] para seleccionar  
"CÓMO PROGRAMAR", y  
presione [ENTER].  
AJUSTE DE CANAL  
AJUSTE DE USER  
AJUSTE DE V-CHIP  
IDIOMA [ESPAÑOL]  
CAPTION [OFF]  
8 Presione [POWER] para ajustar la grabación  
con temporizador automático.  
NOTA:  
El indicador de grabación se enciende.  
• Si todavía no ha ajustado el reloj, aparece el menú  
"AJUSTE MANUAL RELOJ". Ajuste la hora y la  
fecha actuales (consulte "AJUSTE MANUAL DEL  
RELOJ" en página 39) e inicie el ajuste de la  
grabación con temporizador.  
NOTAS:  
DEBE apagar la unidad para activar la grabación  
con temporizador automático.  
Si no se apaga la unidad y sigue  
usted viendo la televisión, "PRG.  
ESTAR LISTO" empieza a parpadear  
en la pantalla del televisor 2 minutos  
antes de la hora de inicio programada.  
– COMO PROGRAMAR –  
2 Utilice [K / L] para seleccionar  
PRG. ESTAR LISTO  
CA FECHA  
INICIO FINAL  
la posición del programa  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- -  
-:- -  
-:- -  
-:- -  
- -  
- -  
- -  
- -  
B
deseado y presione [B].  
Asegúrese de insertar una cinta con lengüeta de  
protección contra borrado antes de apagar la unidad.  
Si la cinta no tiene la lengüeta, será expulsada  
cuando se presione [POWER] para apagar.  
– COMO PROGRAMAR –  
3 Utilice [K / L] hasta que  
aparezca el número del canal  
deseado y presione [B].  
CA FECHA INICIO FINAL  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- -  
-:- -  
-:- -  
- -  
- -  
- -  
B
9 En la hora de inicio programada, la unidad  
NOTA:  
empieza a grabar.  
Si la unidad está conectada a una cajade cable o de  
NOTAS:  
satélite, deberá estar en CA3 o CA4. Seleccione en la  
caja de cable o de satélite el canal donde se va a grabar.  
• La grabación comienza sin encenderse la pantalla  
del televisor.  
Durante la grabación, puede ver solamente el  
programa de televisión que se esté grabando  
actualmente o una reproducción de DVD.  
Presione [POWER] y [SELECT] para seleccionar el  
modo deseado.  
4 Ajuste la fecha de inicio.  
– COMO PROGRAMAR –  
CA FECHA INICIO FINAL  
Para una única grabación :  
Presione [K] hasta que  
aparezca la fecha deseada. A  
continuación, presione [B].  
61 7/03 LUN -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -- -  
-:- -  
-:- -  
-:- -  
-:- - - -  
- -  
- -  
- -  
B
Si la cinta se acaba antes de la hora de finalización, la grabación  
se interrumpe inmediatamente y la cinta es expulsada.  
– COMO PROGRAMAR –  
Para una grabación cada día  
Para grabar el mismo canal a la  
misma hora cada día.  
:
CA FECHA INICIO FINAL  
PARA CONFIRMAR EL PROGRAMA  
61 CADA DIA -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
B
1 Presione [POWER] para encender la unidad.  
L
Presione [ ] hasta que  
(El indicador de grabación se apaga.)  
aparezca "CADA DIA", y  
2 Presione [SET-UP].  
presione [B].  
Utilice [K / L] para seleccionar "CÓMO  
PROGRAMAR", y presione [ENTER].  
– COMO PROGRAMAR –  
CA FECHA INICIO FINAL  
Para una grabación semanal  
Para grabar el mismo canal a la  
misma hora cada semana.  
:
61 CADA LUN -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- -/- - - - - -  
-:- -  
-:- -  
-:- -  
-:- - -
- -  
- -  
- -  
B
3 Confirme los detalles de los programas que  
L
Presione [ ] hasta que aparezca"CADA" y su
aparecen en la pantalla del televisor.  
día deseado de la semana (por ejemplo, "Cada  
lunes"), y presione [B].  
4 Presione [SET-UP] para salir del menú.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
SECCIÓN DVD  
AVANCE RÁPIDO / RETROCESO RÁPIDO  
REPRODUCCIÓN BÁSICA  
• Durante la reproducción, mantenga  
presionado [FWD D] para avance  
rápido o [REV E] para retroceso rápido.  
• Cada vez que mantenga  
1 Presione [POWER] para  
encender la unidad.  
D1  
2 Presione [OPEN/CLOSE A] en la unidad.  
presionado el botón, la  
reproducción se acelera y el  
nivel de velocidad aparece en la pantalla.  
3 Coloque el disco en la  
bandeja, con la etiqueta hacia  
arriba.  
NOTAS:  
En los discos DVD, la velocidad de avance/retroceso  
rápido es diferente según el disco. La velocidad  
aproximada es 1 (×2), 2 (×8), 3 (×20), 4 (×50) y 5 (×100).  
• En discos de CD de audio la velocidad aproximada  
es 1 (×2), 2 (×8) y 3 (×30).  
• Cuando utilice los botones del panel frontal, utilice  
[SEARCH E / D].  
4 Presione [PLAY B].  
• La bandeja se cerrará automáticamente y se  
empezará la reproducción. Cuando reproduzca un  
DVD que incluya un menú de títulos, este menú  
puede aparecer en pantalla.  
Para volver a la reproducción normal, presione [PLAY  
B
].  
NOTAS:  
AVANCE LENTO / RETROCESO LENTO  
• Cerrar la bandeja del disco manualmente o  
presionando [OPEN/CLOSE A] también inicia la  
reproducción.  
Durante la reproducción, presione [PAUSE  
F
].  
• Mantenga presionado [FWD D] para  
• Con discos DVD que utilicen títulos para señales de  
programa de reproducción, la reproducción puede  
comenzar desde el segundo título o puede omitir  
dichos títulos.  
avance lento o [REV E] para retroceso lento.  
• Cada vez que mantenga  
presionado el botón, la  
1
reproducción se ralentiza y el  
nivel de velocidad aparece en la pantalla.  
5 Para congelar la imagen, presione [PAUSE F]  
durante la reproducción.  
NOTAS:  
• La velocidad de avance/retroceso lento varía según  
NOTA:  
el disco. La velocidad aproximada es 1 (1/16), 2 (1/8)  
y 3 (1/2).  
• El sonido se silenciará en modo de pausa.  
• Cuando utilice los botones de la unidad principal,  
utilice [SEARCH E / D].  
6 Presione [STOP C] para  
REPRISE EN COURS  
interrumpir temporalmente la  
Appuyez sur 'PLAY' pour commencer  
à partir d'ici.  
Pour commencer depuis le début,  
appuyez d'abord sur 'STOP' puis sur  
• Para volver a la reproducción normal, presione  
reproducción.  
[PLAY B].  
'PLAY'.  
• Presione [PLAY B] para  
reanudar la reproducción.  
• Para cancelar la reanudación y parar el disco,  
presione [STOP C] de nuevo.  
MENÚ DE DISCO/MENÚ DE TÍTULO  
Un DVD puede contener menús para explorar  
el disco y acceder a funciones especiales.  
NOTAS:  
• La información de reanudación se conserva aunque  
se apague la unidad.  
1 Presione [DISC MENU] o [TITLE].  
• Puede aparecer un "icono  
prohibido" en la zona superior  
derecha de la pantalla del  
Aparecerá el menú principal/menú de título del DVD.  
Puede activar el menú incluso durante la reproducción.  
televisor durante la operación. Esto significa que la  
operación no está disponible en el disco.  
K
L
s
B
] para seleccionar un  
2 Utilice [  
/
/
/
elemento y presione [ENTER].  
REPRODUCCIÓN PASO A PASO  
NOTAS:  
• SI el disco tiene un menú de disco, aparecerán  
distintas opciones de selección: idioma de sonido,  
subtítulos, capítulos del título y otras.  
• El contenido del menú y las correspondientes  
operaciones de menú pueden variar según los  
discos. Para más detalles, consulte el manual que  
acompaña el disco.  
• Durante la reproducción, presione  
[PAUSE F].  
Puede avanzar la imagen fotograma a  
fotograma presionando repetidamente [PAUSE F].  
• Para volver a la reproducción normal, presione  
[PLAY B].  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ES  
FUNAI CORPORATION  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workman-  
ship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this  
warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date  
of original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product  
not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE  
PERFORMED BY AN AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE  
UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:  
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original  
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER.  
FUNAI CORP. will not reimburse you for any service done by unauthorized service providers without prior writ-  
ten approval.  
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please  
contact us at:  
FUNAI CORPORATION  
Customer Service  
Tel :1-800-242-7158  
19900 Van Ness Avenue, Torrance, CA 90501  
Printed in Malaysia  
1EMN21534  
T1203UD★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser MP3 Player MX 200 User Manual
Smooth Fitness Treadmill FX20HR User Manual
Sony MP3 Player D EJ1000 User Manual
Sony Portable CD Player CXS 3100 User Manual
Sony Printer DPP FP30 User Manual
StarTechcom Home Theater System POEINJ1GI User Manual
Sunbeam Iron 3056 User Manual
Sunbeam Microwave Oven SBMW709BLS User Manual
Superior Gas Heater VFST 27VSN 2 User Manual
SUPER MICRO Computer Server AS1041M 82 User Manual