Sylvania CRT Television SRT2232X User Manual
SERVICE MANUAL  
32" COLOR TELEVISION  
SRT2232X  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
<TUNER>  
ANT. Input ------------------- 75ohm Unbal., F type  
Reference Level ----------- 20Vp-p (CRT Green Cathode)  
Test Input Signal ---------- 400Hz 30% modulation  
Description  
Condition  
Unit  
Nominal  
Limit  
1. Intermediate Freq.  
Picture  
Sound  
MHz  
MHz  
45.75  
41.25  
2. Peak Picture Sens  
VHF  
CATV  
UHF  
dBµV  
dBµV  
dBµV  
15  
15  
15  
30  
30  
40  
3. AFT Pull In Range (10mV input)  
MHz  
2.2  
0.7  
<DEFLECTION>  
Description  
Condition  
Unit  
Nominal  
Limit  
1. Deflection Freq.  
Horizontal  
Vertical  
KHz  
Hz  
15.734  
60  
2. Linearity  
Horizontal  
Vertical  
%
%
15  
10  
3. Over Scan  
%
10  
29  
4. High Voltage  
KV  
<VIDEO & CHROMA>  
Description  
Condition  
Unit  
Nominal  
Limit  
1. Misconvergence  
Center  
Side  
Corner  
mm  
mm  
mm  
0.4  
1.5  
2.1  
2. Brightness  
APL 100%  
Ft-L  
°K  
20  
15  
3. Color Temperature  
4. Resolution  
9200°K  
Horizontal  
Vertical  
Line  
Line  
250  
300  
<AUDIO>  
All items are measured across 8Ω load at speaker output terminal.  
Description  
Condition  
10% THD  
500mW  
-3dB  
Unit  
W
Nominal  
3
Limit  
2.4  
7
1. Audio Output Power  
2. Audio Distortion (w/LPF)  
3. Audio Freq. Response  
%
1.0  
Hz  
90~11K  
Note:  
Nominal specifications represent the design specifications. All units should be able to approximate  
these. Some will exceed and some may drop slightly below these specifications. Limit specifications  
represent the absolute worst condition that still might be considered acceptable. In no case should  
a unit fail to meet limit specifications.  
1-1  
L6650SP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY PRECAUTIONS  
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical  
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally  
important to implement the following precautions when a set is being serviced.  
age current tester or a metering system that com-  
plies with American National Standards Institute  
Safety Precautions for TV Circuit  
1. Before returning an instrument to the custom-  
er, always make a safety check of the entire instru-  
ment, including, but not limited to, the following  
items:  
(ANSI) C101.1 Leakage Current for Appliances  
and Underwriters Laboratories (UL) 1410, (50.7).  
With the instrument AC switch first in the on posi-  
tion and then in the off position, measure from a  
known earth ground (metal water pipe, conduit,  
etc.) to all exposed metal parts of the instrument  
(antennas, handle brackets, metal cabinet, screw  
heads, metallic overlays, control shafts, etc.), es-  
pecially any exposed metal parts that offer an elec-  
trical return path to the chassis. Any current  
measured must not exceed 0.5 milli-ampere. Re-  
verse the instrument power cord plug in the outlet  
and repeat the test.  
a. Be sure that no built-in protective devices are de-  
fective and have been defeated during servicing.  
(1) Protective shields are provided on this chassis  
to protect both the technician and the customer.  
Correctly replace all missing protective shields, in-  
cluding any removed for servicing convenience.  
(2) When reinstalling the chassis and/or other as-  
sembly in the cabinet, be sure to put back in place  
all protective devices, including but not limited to,  
nonmetallic control knobs, insulating fishpapers,  
adjustment and compartment covers/shields, and  
isolation resistor/capacitor networks. Do not oper-  
ate this instrument or permit it to be operated  
without all protective devices correctly in-  
stalled and functioning. Servicers who defeat  
safety features or fail to perform safety checks  
may be liable for any resulting damage.  
READING SHOULD  
NOT BE ABOVE 0.5 mA  
LEAKAGE  
CURRENT  
DEVICE  
BEING  
TESTED  
TESTER  
_
+
TEST ALL EXPOSED  
METAL SURFACES  
b. Be sure that there are no cabinet openings through  
which an adult or child might be able to insert their  
fingers and contact a hazardous voltage. Such  
openings include, but are not limited to, (1) spac-  
ing between the picture tube and the cabinet  
mask, (2) excessively wide cabinet ventilation  
slots, and (3) an improperly fitted and/or incorrectly  
secured cabinet back cover.  
ALSO TEST WITH  
PLUG REVERSED  
USING AC  
ADAPTER PLUG  
AS REQUIRED  
EARTH  
GROUND  
c. Antenna Cold Check - With the instrument AC  
plug removed from any AC source, connect an  
electrical jumper across the two AC plug prongs.  
Place the instrument AC switch in the on position.  
Connect one lead of an ohmmeter to the AC plug  
prongs tied together and touch the other ohmme-  
ter lead in turn to each tuner antenna input ex-  
posed terminal screw and, if applicable, to the  
coaxial connector. If the measured resistance is  
less than 1.0 megohm or greater than 5.2 mego-  
hm, an abnormality exists that must be corrected  
before the instrument is returned to the customer.  
Repeat this test with the instrument AC switch in  
the off position.  
ANY MEASUREMENTS NOT WITHIN THE LIMITS  
SPECIFIED HEREIN INDICATE A POTENTIAL  
SHOCK HAZARD THAT MUST BE ELIMINATED  
BEFORE RETURNING THE INSTRUMENT TO  
THE CUSTOMER OR BEFORE CONNECTING  
THE ANTENNA OR ACCESSORIES.  
e. X-Radiation and High Voltage Limits - Because  
the picture tube is the primary potential source of  
X-radiation in solid-state TV receivers, it is special-  
ly constructed to prohibit X-radiation emissions.  
For continued X-radiation protection, the replace-  
ment picture tube must be the same type as the  
original. Also, because the picture tube shields  
and mounting hardware perform an X-radiation  
protection function, they must be correctly in place.  
High voltage must be measured each time servic-  
d. Leakage Current Hot Check - With the instru-  
ment completely reassembled, plug the AC line  
cord directly into a 120V AC outlet. (Do not use an  
isolation transformer during this test.) Use a leak-  
2-1  
L6115IMP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ing is performed that involves B+, horizontal de-  
flection or high voltage. Correct operation of the X-  
radiation protection circuits also must be recon-  
firmed each time they are serviced. (X-radiation  
protection circuits also may be called "horizontal  
disable" or "hold down.") Read and apply the high  
voltage limits and, if the chassis is so equipped,  
the X-radiation protection circuit specifications giv-  
en on instrument labels and in the Product Safety  
& X-Radiation Warning note on the service data  
chassis schematic. High voltage is maintained  
within specified limits by close tolerance safety-re-  
lated components/adjustments in the high-voltage  
circuit. If high voltage exceeds specified limits,  
check each component specified on the chassis  
schematic and take corrective action.  
earth ground. If a voltage reading in excess of 1.0V  
is obtained, remove and reinsert the AC power  
plug in the opposite polarity and again measure  
the voltage potential between the chassis and a  
known earth ground.  
b. Some TV receiver chassis normally have 85V  
AC(RMS) between chassis and earth ground re-  
gardless of the AC plug polarity. This chassis can  
be safety-serviced only with an isolation transform-  
er inserted in the power line between the receiver  
and the AC power source, for both personnel and  
test equipment protection.  
c. Some TV receiver chassis have a secondary  
ground system in addition to the main chassis  
ground. This secondary ground system is not iso-  
lated from the AC power line. The two ground sys-  
tems are electrically separated by insulation  
material that must not be defeated or altered.  
2. Read and comply with all caution and safety-relat-  
ed notes on or inside the receiver cabinet, on the  
receiver chassis, or on the picture tube.  
6. Observe original lead dress. Take extra care to as-  
sure correct lead dress in the following areas:a.  
near sharp edges,b. near thermally hot parts-be  
sure that leads and components do not touch ther-  
mally hot parts,c. the AC supply,d. high voltage,  
and,e. antenna wiring. Always inspect in all areas  
for pinched, out of place, or frayed wiring. Check  
AC power cord for damage.  
3. Design Alteration Warning - Do not alter or add  
to the mechanical or electrical design of this TV re-  
ceiver. Design alterations and additions, including,  
but not limited to circuit modifications and the ad-  
dition of items such as auxiliary audio and/or video  
output connections, might alter the safety charac-  
teristics of this receiver and create a hazard to the  
user. Any design alterations or additions will void  
the manufacturer's warranty and may make you,  
the servicer, responsible for personal injury or  
property damage resulting therefrom.  
7. Components, parts, and/or wiring that appear to  
have overheated or are otherwise damaged  
should be replaced with components, parts, or wir-  
ing that meet original specifications. Additionally,  
determine the cause of overheating and/or dam-  
age and, if necessary, take corrective action to re-  
move any potential safety hazard.  
4. Picture Tube Implosion Protection Warning -  
The picture tube in this receiver employs integral  
implosion protection. For continued implosion pro-  
tection, replace the picture tube only with one of  
the same type number. Do not remove, install, or  
otherwise handle the picture tube in any manner  
without first putting on shatterproof goggles  
equipped with side shields. People not so  
equipped must be kept safely away while picture  
tubes are handled. Keep the picture tube away  
from your body. Do not handle the picture tube by  
its neck. Some "in-line" picture tubes are equipped  
with a permanently attached deflection yoke; be-  
cause of potential hazard, do not try to remove  
such "permanently attached" yokes from the pic-  
ture tube.  
8. Product Safety Notice - Some electrical and me-  
chanical parts have special safety-related charac-  
teristics which are often not evident from visual  
inspection, nor can the protection they give neces-  
sarily be obtained by replacing them with compo-  
nents rated for higher voltage, wattage, etc.. Parts  
that have special safety characteristics are identi-  
fied by a ( # ) on schematics and in parts lists. Use  
of a substitute replacement that does not have the  
same safety characteristics as the recommended  
replacement part might create shock, fire, and/or  
other hazards. The product's safety is under re-  
view continuously and new instructions are issued  
whenever appropriate. Prior to shipment from the  
factory, our products are strictly inspected to con-  
firm they comply with the recognized product safe-  
ty and electrical codes of the countries in which  
they are to be sold. However, in order to maintain  
such compliance, it is equally important to imple-  
ment the following precautions when a set is being  
serviced.  
5. Hot Chassis Warning -  
a. Some TV receiver chassis are electrically connect-  
ed directly to one conductor of the AC power cord  
and maybe safety-serviced without an isolation  
transformer only if the AC power plug is inserted  
so that the chassis is connected to the ground side  
of the AC power source. To confirm that the AC  
power plug is inserted correctly, with an AC volt-  
meter, measure between the chassis and a known  
2-2  
L6115IMP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3) Align the lengths of the wires to be connected. In-  
sert the wires fully into the connector.  
Precautions during Servicing  
A. Parts identified by the ( # ) symbol are critical for  
safety.  
4) Use the crimping tool to crimp the metal sleeve at  
the center position. Be sure to crimp fully to the  
complete closure of the tool.  
Replace only with part number specified.  
B. In addition to safety, other parts and assemblies  
are specified for conformance with regulations ap-  
plying to spurious radiation. These must also be  
replaced only with specified replacements.  
L. When connecting or disconnecting the internal  
connectors, first, disconnect the AC plug from the  
AC supply outlet.  
Examples: RF converters, RF cables, noise block-  
ing capacitors, and noise blocking filters, etc.  
C. Use specified internal wiring. Note especially:  
1) Wires covered with PVC tubing  
2) Double insulated wires  
3) High voltage leads  
D. Use specified insulating materials for hazardous  
live parts. Note especially:  
1) Insulation Tape  
2) PVC tubing  
3) Spacers  
4) Insulators for transistors.  
E. When replacing AC primary side components  
(transformers, power cord, etc.), wrap ends of  
wires securely about the terminals before solder-  
ing.  
F. Observe that the wires do not contact heat produc-  
ing parts (heatsinks, oxide metal film resistors, fus-  
ible resistors, etc.)  
G. Check that replaced wires do not contact sharp  
edged or pointed parts.  
H. When a power cord has been replaced, check that  
5~6 kg of force in any direction will not loosen it.  
I. Also check areas surrounding repaired locations.  
J. Use care that foreign objects (screws, solder drop-  
lets, etc.) do not remain inside the set.  
K. Crimp type wire connector  
The power transformer uses crimp type connec-  
tors which connect the power cord and the primary  
side of the transformer. When replacing the trans-  
former, follow these steps carefully and precisely  
to prevent shock hazards.  
Replacement procedure  
1) Remove the old connector by cutting the wires at  
a point close to the connector.  
Important: Do not re-use a connector (discard it).  
2) Strip about 15 mm of the insulation from the ends  
of the wires. If the wires are stranded, twist the  
strands to avoid frayed conductors.  
2-3  
L6115IMP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Check after Servicing  
Examine the area surrounding the repaired location  
for damage or deterioration. Observe that screws,  
parts and wires have been returned to original posi-  
tions. Afterwards, perform the following tests and con-  
firm the specified values in order to verify compliance  
with safety standards.  
Chassis or Secondary Conductor  
Primary Circuit Terminals  
d'  
d
1. Clearance Distance  
When replacing primary circuit components, confirm  
specified clearance distance (d) and (d') between sol-  
dered terminals, and between terminals and surround-  
ing metallic parts. (See Fig. 1)  
Table 1 : Ratings for selected area  
Clearance  
AC Line Voltage  
Region  
Fig. 1  
Distance (d) (d')  
USA or  
CANADA  
≥ 3.2 mm  
(0.126 inches)  
110 to 130 V  
Exposed Accessible Part  
Note: This table is unofficial and for reference only.  
Be sure to confirm the precise values.  
Z
2. Leakage Current Test  
Confirm the specified (or lower) leakage current be-  
tween B (earth ground, power cord plug prongs) and  
externally exposed accessible parts (RF terminals,  
antenna terminals, video and audio input and output  
terminals, microphone jacks, earphone jacks, etc.) is  
lower than or equal to the specified value in the table  
below.  
AC Voltmeter  
(High Impedance)  
1.5kΩ  
0.15µF  
Earth Ground  
Power Cord Plug Prongs  
B
Measuring Method : (Power ON)  
Fig. 2  
Insert load Z between B (earth ground, power cord  
plug prongs) and exposed accessible parts. Use an  
AC voltmeter to measure across both terminals of  
load Z. See Fig. 2 and following table.  
Table 2 : Leakage current ratings for selected areas  
AC Line Voltage  
Region  
Load Z  
Leakage Current (i)  
Earth Ground (B) to:  
0.15µF CAP. & 1.5kΩ  
RES. connected in  
parallel  
Exposed accessible  
parts  
110 to 130 V  
USA  
i≤0.5mA rms  
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.  
2-4  
L6115IMP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STANDARD NOTES FOR SERVICING  
(2) Remove the flat pack-IC with tweezers while ap-  
Circuit Board Indications  
a. The output pin of the 3 pin Regulator ICs is indicat-  
ed as shown.  
plying the hot air.  
(3) Bottom of the flat pack-IC is fixed with glue to the  
CBA; when removing entire flat pack-IC, first apply  
soldering iron to center of the flat pack-IC and heat  
up. Then remove (glue will be melted). (Fig. S-1-6)  
Top View  
Bottom View  
Input  
(4) Release the flat pack-IC from the CBA using twee-  
zers. (Fig. S-1-6)  
Out  
In  
Caution:  
b. For other ICs, pin 1 and every fifth pin are indicat-  
ed as shown.  
1. Do not supply hot air to the chip parts around the  
flat pack-IC for over 6 seconds because damage  
to the chip parts may occur. Put masking tape  
around the flat pack-IC to protect other parts from  
damage. (Fig. S-1-2)  
5
Pin 1  
2. The flat pack-IC on the CBA is affixed with glue, so  
be careful not to break or damage the foil of each  
pin or the solder lands under the IC when remov-  
ing it.  
10  
c. The 1st pin of every male connector is indicated as  
shown.  
Hot-air  
Flat Pack-IC  
Desoldering  
Machine  
CBA  
Pin 1  
How to Remove / Install Flat Pack-IC  
1. Removal  
With Hot-Air Flat Pack-IC Desoldering Machine:  
Masking  
Tape  
Flat Pack-IC  
(1) Prepare the hot-air flat pack-IC desoldering ma-  
chine, then apply hot air to the Flat Pack-IC (about  
5 to 6 seconds). (Fig. S-1-1)  
Tweezers  
Fig. S-1-2  
Fig. S-1-1  
3-1  
L6115STA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
With Soldering Iron:  
soldering iron to center of the flat pack-IC and heat  
up. Then remove (glue will be melted). (Fig. S-1-6)  
(1) Using desoldering braid, remove the solder from  
all pins of the flat pack-IC. When you use solder  
flux which is applied to all pins of the flat pack-IC,  
you can remove it easily. (Fig. S-1-3)  
(5) Release the flat pack-IC from the CBA using twee-  
zers. (Fig. S-1-6)  
Note:  
When using a soldering iron, care must be taken to  
ensure that the flat pack-IC is not being held by  
glue. When the flat pack-IC is removed from the  
CBA, handle it gently because it may be damaged  
if force is applied.  
Desoldering Braid  
Flat Pack-IC  
Hot Air Blower  
Soldering Iron  
Fig. S-1-3  
or  
(2) Lift each lead of the flat pack-IC upward one by  
one, using a sharp pin or wire to which solder will  
not adhere (iron wire). When heating the pins, use  
a fine tip soldering iron or a hot air desoldering ma-  
chine.(Fig. S-1-4)  
Iron Wire  
Soldering Iron  
To Solid  
Mounting Point  
Fig. S-1-5  
Sharp  
Pin  
Fine Tip  
Soldering Iron  
CBA  
Fine Tip  
Soldering Iron  
Fig. S-1-4  
(3) Bottom of the flat pack-IC is fixed with glue to the  
CBA; when removing entire flat pack-IC, first apply  
soldering iron to center of the flat pack-IC and heat  
up. Then remove (glue will be melted). (Fig. S-1-6)  
Flat Pack-IC  
Tweezers  
(4) Release the flat pack-IC from the CBA using twee-  
zers. (Fig. S-1-6)  
Fig. S-1-6  
With Iron Wire:  
(1) Using desoldering braid, remove the solder from  
all pins of the flat pack-IC. When you use solder  
flux which is applied to all pins of the flat pack-IC,  
you can remove it easily. (Fig. S-1-3)  
(2) Affix the wire to a workbench or solid mounting  
point, as shown in Fig. S-1-5.  
(3) While heating the pins using a fine tip soldering  
iron or hot air blower, pull up the wire as the solder  
melts so as to lift the IC leads from the CBA con-  
tact pads as shown in Fig. S-1-5.  
(4) Bottom of the flat pack-IC is fixed with glue to the  
CBA; when removing entire flat pack-IC, first apply  
3-2  
L6115STA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation  
Instructions for Handling  
Semiconductors  
Electrostatic breakdown of the semiconductors may  
occur due to a potential difference caused by electro-  
static charge during unpacking or repair work.  
(1) Using desoldering braid, remove the solder from  
the foil of each pin of the flat pack-IC on the CBA  
so you can install a replacement flat pack-IC more  
easily.  
(2) The "I" mark on the flat pack-IC indicates pin 1.  
(See Fig. S-1-7.) Be sure this mark matches the 1  
on the PCB when positioning for installation. Then  
pre- solder the four corners of the flat pack-IC.  
(See Fig. S-1-8.)  
1. Ground for Human Body  
Be sure to wear a grounding band (1MΩ) that is prop-  
erly grounded to remove any static electricity that may  
be charged on the body.  
(3) Solder all pins of the flat pack-IC. Be sure that  
none of the pins have solder bridges.  
2. Ground for Workbench  
Be sure to place a conductive sheet or copper plate  
with proper grounding (1MΩ) on the workbench or  
other surface, where the semiconductors are to be  
placed. Because the static electricity charge on cloth-  
ing will not escape through the body grounding band,  
be careful to avoid contacting semiconductors with  
your clothing.  
Example :  
<Incorrect>  
Pin 1 of the Flat Pack-IC  
is indicated by a " " mark.  
Fig. S-1-7  
Presolder  
CBA  
<Correct>  
Grounding Band  
Flat Pack-IC  
CBA  
Fig. S-1-8  
1MΩ  
CBA  
1MΩ  
Conductive Sheet or  
Copper Plate  
3-3  
L6115STA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CABINET DISASSEMBLY INSTRUCTIONS  
Note:  
1. Disassembly Flowchart  
(1) Order of steps in procedure. When reassembling,  
follow the steps in reverse order.These numbers  
are also used as the Identification (location) No. of  
parts in figures.  
This flowchart indicates the disassembly steps for the  
cabinet parts, and the CBA in order to gain access to  
item(s) to be serviced. When reassembling, follow the  
steps in reverse order. Bend, route and dress the  
cables as they were.  
(2) Parts to be removed or installed.  
(3) Fig. No. showing procedure of part location  
Caution !  
(4) Identification of part to be removed, unhooked, un-  
locked, released, unplugged, unclamped, or des-  
oldered.  
When removing the CRT, be sure to discharge the  
Anode Lead of the CRT with the CRT Ground Wire  
before removing the Anode Cap.  
S=Screw, P=Spring, L=Locking Tab, CN=Con-  
nector, *=Unhook, Unlock, Release, Unplug, or  
Desolder  
[1] Rear Cabinet  
2(S-2) = two Screws (S-2)  
(5) Refer to the following "Reference Notes in the  
Table."  
[2] CRT CBA  
Reference Notes in the Table  
1. Removal of the Rear Cabinet. Remove screws  
7(S-1), 1(S-2) and 3(S-4) then slide the Rear Cab-  
inet backward.  
[3] Main CBA  
[4] CRT  
2. Removal of the CRT CBA. Disconnect CN1501  
then pull the CRT CBA backward.  
Caution !  
2. Disassembly Method  
Discharge the Anode Lead of the CRT with the CRT  
Ground Wire before removing the Anode Cap.  
Removal  
3. Removal of the Main CBA. First, disconnect  
CN571, CN801, CN802, and CN691 on the Main  
CBA. Second, remove Anode Cap. then slide the  
Main CBA backward.  
Step/  
Loc. No.  
Remove/*unlock/  
Part  
Fig.  
release/unplug/  
Note  
No  
unclamp/desolder  
Rear  
Cabinet  
7(S-1), 1(S-2),  
3(S-4)  
[1]  
[2]  
1,2  
4,5  
1
2
4. Removal of the CRT. Remove screws 4(S-3) then  
slide the CRT backward.  
CRT CBA  
Main CBA  
CRT  
CN1501  
CN571, CN801,  
CN802, CN691,  
Anode Cap  
[3]  
[4]  
3,5  
4
3
4
4(S-3)  
↓
(1)  
↓
(2)  
↓
(3)  
↓
(4)  
↓
(5)  
4-1  
L6650DC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S-1  
S-1  
S-1  
[3] Main CBA  
S-2  
S-4  
S-1  
[1] Rear Cabinet  
Fig. 1  
Fig. 3  
Anode Cap  
S-3  
S-1  
S-1  
S-1  
S-4  
S-2  
S-1  
S-3  
S-3  
S-1  
S-1  
S-1  
S-3  
[4] CRT  
[1] Rear Cabinet  
Fig. 2  
Fig. 4  
4-2  
L6650DC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV Cable Wiring Diagram  
SP802  
SP801  
L691 DEGAUSSING COIL  
MAIN CBA  
CLN802  
CLN801  
CN801  
CN802  
WH301A  
CN691  
TU1  
TUNER  
FLYBACK TRANSFORMER  
T571  
WH501A  
CN571  
AC601  
AC CORD  
FOCUS  
SCREEN  
WH301B  
WH501B  
ANODE  
CN1501  
Fig. 5  
TO CRT GROUND  
4-3  
L6650DC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRICAL ADJUSTMENT INSTRUCTIONS  
General Note:  
"CBA" is abbreviation for "Circuit Board Assem-  
bly."  
How to set up the service mode:  
Service mode:  
1. Use the service remote control unit.  
2. Turn the power on. (Use main power on the TV  
unit.)  
3. Press "SLEEP" button on the service remote con-  
trol unit. Version of micro computer will display on  
the CRT. (Ex: 054-0.05)  
NOTE:  
Electrical adjustments are required after replacing  
circuit components and certain mechanical parts.  
It is important to perform these adjustments only  
after all repairs and replacements have been com-  
pleted.  
4. Check the display on the lower left is "3815" and if  
it is not "3815," set it at "3815" according to "2. Ini-  
tial Setting."  
Also, do not attempt these adjustments unless the  
proper equipment is available.  
Test Equipment Required  
1. NTSC Pattern Generator (Color Bar W/White  
Window, Red Color, Dot Pattern, Gray Scale,  
Monoscope, Multi-Burst)  
2. DC Voltmeter  
3. Oscilloscope: Dual-trace with 10:1 probe,  
V-Range:0.001~50V/Div,  
1. +B Adjustment  
Purpose: To obtain correct operation.  
Symptom of Misadjustment: The picture is dark and  
the unit does not operate correctly.  
Test Point  
Adj. Point  
Mode  
Input  
F-Range: DC~AC-60MHz  
4. Plastic Tip Driver  
5. Remote control unit: Part No. N0138UD or N0139UD  
6. DC power supply 13.2V/5A  
TP601(+B)  
TP300(GND)  
VR661  
---  
---  
Tape  
M. EQ.  
Spec.  
+132 0.5V DC.  
---  
DC Voltmeter  
How to make Service remote control unit:  
1. Prepare normal remote control unit. (Part No.  
N0138UD or N0139UD) Remove 3 Screws from  
the back lid. (Fig. 1-1)  
Note:TP601, TP300(GND), VR661 --- Main CBA  
1. Connect DC Volt Meter to TP601 and TP300(GND).  
2. Adjust VR661 so that the voltage of TP601 becomes  
+132 0.5V DC.  
2. Added J1 (Jumper Wire) to the remote control CBA.  
(Fig. 1-2)  
SCREWS  
Fig. 1-1  
Fig. 1-2  
REMOTE CONTROL UNIT  
REMOTE CONTROL CBA  
Notes:  
1. The service remote control unit that be made in  
above method is usable in the electrical adjustment  
of the following models.  
SRT2313/2319, SRT2213B/2219B, SRT2227X,  
SRT2223X, SRT2223B, SRT2232X, SRT2220P  
SRT4127P  
2. The attached remote control unit can not be used  
as service remote control unit.  
5-1  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Initial Setting  
3. AV Memory Setting data  
General  
General  
1. Enter the Service mode. (See page 5-1)  
2. Press "VOL p" button on the service remote control  
unit. Display changes "C/D," "7F," "LANGUAGE,"  
"ACCESS CODE," "SOUND TYPE," "VIDEO  
TONE," "FM MODE," "V-OUT," "VIDEO," "AV  
MEMO," "STABLE SOUND," "FILTER," "300," and  
"YUV MEMORY" cyclically when "VOL p" button is  
pressed.  
1. Enter the Service mode. (See page 5-1)  
2. When “AV MEMORY” setting to “ON” (refer to “2-1.  
Setting for 7F, CHROMA, LANGUAGE, STEREO  
TYPE, ACCESS CODE, STABLE SOUND, COMB  
FILTER, COMPONENT and AV MEMORY data  
Values”), press "VOL o" button on the service re-  
mote control unit. Display changes "SPORT CNT,"  
"SPORT CLR," "SPORT SRP," "NEWS CNT,"  
"NEWS CLR," "NEWS SRP," "MOVIE CNT,"  
"MOVIE CLR," and "MOVIE SRP" cyclically when  
"VOL o" button is pressed.  
3. To set the following each data value, press "CH  
p" buttons on the service remote control unit.  
o
/
7F --- Set to "FF."  
3. To set the following each data value, press "CH  
p" buttons on the service remote control unit.  
o
LANGUAGE --- Set to "SPA."  
ACCESS CODE --- Set to "ON."  
SOUND TYPE --- Set to "MTS."  
VIDEO TONE --- Set to "ON."  
FM-MODE --- Set to "OFF."  
V-OUT --- Set to "OFF."  
/
SPORT CNT--- Set to "48."  
SPORT CLR--- Set to "30."  
SPORT SRP--- Set to "34."  
NEWS CNT--- Set to "39."  
NEWS CLR--- Set to "30."  
NEWS SRP--- Set to "28."  
MOVIE CNT--- Set to "43."  
MOVIE CLR--- Set to "26."  
MOVIE SRP--- Set to "24."  
VIDEO --- Set to "V1/V2."  
AV MEMO --- Set to "ON."  
STABLE SOUND --- Set to "OFF."  
FILTER --- Set to "ON."  
Adjusting the monitoring time --- Set to "500."  
YUV MEMORY --- Set to "OFF."  
5-2  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S-TNT  
4. Setting for BRIGHT, CONTRAST,  
COLOR, TINT and SHARPNESS  
data Values  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "S-TINT" (S-TNT) display.  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "S-TINT" (S-TNT)  
becomes 59.  
General  
1. Enter the Service mode. (See page 5-1)  
2. Press "MENU" button on the service remote control  
unit. Display changes "BRT," "CNT," "CLR," "S-  
CLR," "C-CLR," "TNT," "V-TNT," "S-TNT," "C-  
TNT," "SHARP," "S-SRP," and "C-SRP" cyclical-  
ly when "MENU" button is pressed.  
C-TNT  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "COMPONENT TINT" (C-  
TNT) display.  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "COMPONENT  
TINT" (C-TNT) becomes 58.  
CNT  
1. Press "MENU" button on the service remote control  
unit. Then select "CONTRAST" (CNT) display.  
SHARP  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "CONTRAS" (CNT)  
becomes 84.  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "SHARPNESS" (SHARP) dis-  
play.  
CLR  
2. Press "CH o/p" buttons on the service remote  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "COLOR" (CLR) display.  
control unit and select "47."  
S-SRP  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "COLOR" (CLR)  
becomes 56.  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "S-SHARPNESS" (S-SRP)  
display.  
S-CLR  
2. Press "CH o/p" buttons on the service remote  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "S-COLOR" (S-CLR) display.  
control unit and select "47."  
C-SRP  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "S-COLOR" (S-  
CLR) becomes 56.  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "COMPONENT SHARP-  
NESS" (C-SRP) display.  
C-CLR  
2. Press "CH o/p" buttons on the service remote  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "COMPONENT COLOR" (C-  
CLR) display.  
control unit and select "47."  
Note: BRIGHT data value does not need to be adjust-  
ed at this moment.  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "COMPONENT  
COLOR" (C-CLR) becomes 56.  
TNT  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "TINT" (TNT) display.  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "TINT" (TNT) be-  
comes 62.  
V-TNT  
1. Press "MENU" button on the service remote con-  
trol unit. Then select "V-TINT" (V-TNT) display.  
2. Press "CH o/p" buttons on the service remote  
control unit so that the value of "V-TINT" (V-TNT)  
becomes 62.  
5-3  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Black Stretch Control Adjustment  
Purpose: To show the fine black color.  
SD Check mode (Factory mode)  
Symptom of Misadjustment: Black color will not  
appear correctly.  
Press "1" buton.  
Note: Use service remote control unit.  
1. Enter the Service mode. (See page 5-1)  
7
2. Press "6" button on the service remote control unit.  
"B-S" is indicated.  
Please wait  
OSD color:  
Magenta  
3. Press "CH o / p" buttons on the service remote con-  
trol unit so that display will change "OFF," "0," and  
"1." Then choose "B-S OFF."  
There is no SD after  
selecting channel.  
4. Press "6" button on the service remote control unit.  
"B-S2" is indicated.  
13  
Please wait  
5. Press "CH o / p" buttons on the service remote  
control unit so that display will change "0" and "1."  
Then choose "B-S2 0."  
There are SD  
in all channel.  
OSD color:  
Magenta  
6. Turn the power off and on again, using the main  
power button on the TV unit.  
26  
OK  
30  
NG  
6. Purity Check  
1. Enter the Service mode. (See page 5-1)  
OSD color:  
Magenta  
OSD color:  
Magenta  
2. Press "7" button on the remote control unit. Each  
time pressing 7" button on the remote control unit,  
display changes Red mode, Green mode, Blue  
mode, and White mode cyclically.  
When SD-Check starting,  
there is no ADD channel.  
3. Select White mode.  
4. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
ADD nothing  
7. SD Check Mode  
OSD color:  
Magenta  
1. Enter the Service mode. (See page 5-1)  
2. Press "1" button on the remote control unit. The  
unit enter the SD-Check mode.  
3. The unit starts selecting the added channel from  
first channel according to the memorized CH ADD/  
DELL data and CATV/TV data in RAM.  
5-4  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. H. Position Adjustment  
Purpose: To obtain correct horizontal position of  
10. V. Position Adjustment  
Purpose: To obtain correct vertical width of screen  
image.  
screen image.  
Symptom of misadjustment: If V. Position is incor-  
rect, vertical height of image on the screen may not be  
properly displayed.  
Symptom of Misadjustment: If H. Position is incor-  
rect, horizontal position of image on the screen may  
not be properly displayed.  
Test Point  
Adj. Point  
CH o /  
buttons  
Mode  
Input  
Test Point  
Adj. Point  
CH o /  
buttons  
Mode  
Input  
p
Mono-  
scope  
p
Mono-  
scope  
---  
RF  
---  
RF  
Tape  
M. EQ.  
Spec.  
See below.  
Tape  
M. EQ.  
Spec.  
90 5%  
---  
Monoscope  
---  
Monoscope  
Note: Use service remote control unit  
Note: Use service remote control unit  
1. Operate the unit for at least 20 minutes.  
2. Enter the Service Mode. (See page 5-1)  
3. Receive the monoscope pattern.  
1. Operate the unit for at least 20 minutes.  
2. Enter the Service mode. (See page 5-1)  
3. Receive the monoscope pattern.  
4. Press "9" button on the service remote control unit  
and select "V-P" mode. (Display change "V-S" and  
"V-P" cyclically when "9" button is pressed).  
4. Press "8" button on the remote control unit.  
"H-P" is indicated.  
5. Press "CH o/p" buttons on the service remote  
control unit so that the monoscope pattern will be  
90 5% of display size and the circle is round.  
5. Press "CH o/p" buttons on the service remote  
control unit so that the top and bottom of the mono-  
scope pattern will be equal of each other.  
6. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
6. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
9. V. Size Adjustment  
11. U-Pedestal Adjustment  
Purpose: To obtain correct vertical width of screen image.  
1. In VIDEO mode of V1, V2, or YUV, press "3" button  
on the service remote control unit and select "U-  
PED" mode. (Display changes "U-PED" and "V-  
PED" cyclically when "3" button is pressed).  
Symptom of Misadjustment: If V. Size is incorrect, vertical  
size of image on the screen may not be properly displayed.  
Test Point  
Adj. Point  
CH o /  
buttons  
Mode  
Input  
2. Switch the VIDEO mode to YUV. (Refer to “2. Initial  
Setting.”)  
p
Mono-  
scope  
---  
RF  
3. To select one appropriate value in "0" to "15,"  
press "CH o / p" buttons on the remote control  
unit.  
Tape  
M. EQ.  
Spec.  
90 5%  
---  
Monoscope  
4. Switch the VIDEO mode to previous mode.  
Note: Use service remote control unit.  
5. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
1. Operate the unit for at least 20 minutes.  
2. Enter the Service mode. (See page 5-1)  
3. Receive the monoscope pattern.  
4. Press "9" button on the service remote control unit  
and select "V-S" mode. (Display changes "V-S" and  
"V-P" cyclically when "9" button is pressed).  
5. Press "CH o/p" buttons on the service remote  
control unit so that the monoscope pattern will be  
90 5% of display size and the circle is round.  
6. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
5-5  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. V-Pedestal Adjustment  
15. PIN Cushion Adjustment  
1. In VIDEO mode of V1, V2, or YUV, press "3" button  
on the service remote control unit and select "V-  
PED" mode. (Display changes "U-PED" and "V-  
PED" cyclically when "3" button is pressed).  
Purpose: To obtain correct straight vertical line of  
screen image.  
Symptom of Misadjustment: If H.Pin cushion is incor-  
rect, vertical line of image on the screen may not be  
properly displayed.  
2. Switch the VIDEO mode to YUV. (Refer to “2. Initial  
Setting.”)  
Test Point  
Adj. Point  
Mode  
Input  
3. To select one appropriate value in "0" to "15,"  
press "CH o / p" buttons on the remote control  
unit.  
Cross  
hatch  
---  
VR561  
RF  
4. Switch the input mode to previous mode.  
Tape  
M. EQ.  
Spec.  
5. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
---  
Cross hatch  
Note: Use service remote control unit  
13. Software Reset  
To reset software, press “5” button on the remote con-  
trol unit for at least 5 seconds after pressing “CH  
RETURN” button on the remote control unit.  
1. Operate the unit for at least 20 minutes.  
2. Receive the Cross hatch Pattern.  
3. Adjust VR561 so that the cross hatch pattern will  
be straight line of display.  
14. H. Size Adjustment  
Purpose: To obtain correct horizontal size of screen  
image.  
4. Turn the Power off and on again. (Main power but-  
ton on the TV unit.)  
Symptom of Misadjustment: If H. Size is incorrect,  
horizontal size of image on the screen may not be  
properly displayed.  
Test Point  
Adj. Point  
Mode  
Input  
Mono-  
scope  
---  
VR562  
RF  
Tape  
M. EQ.  
Spec.  
90 5%  
---  
Monoscope  
Note: Use service remote control unit  
1. Operate the unit for at least 20 minutes.  
2. Receive the Monoscope Pattern.  
3. Adjust VR562 so that the monoscope pattern will  
be 90 5% of display size and circle is round.  
4. Turn the Power off and on again. (Main power but-  
ton on the TV unit.)  
5-6  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16. Cut-off Adjustment  
Purpose: To adjust the beam current of R, G, B, and  
screen voltage.  
17. White Balance Adjustment  
Purpose: To mix red, green and blue beams correctly  
for pure white.  
Symptom of Misadjustment: White color may be  
reddish, greenish or bluish.  
Symptom of Misadjustment: White becomes bluish  
or reddish.  
Test Point  
Adj. Point  
Mode  
Input  
Test Point  
Adj. Point  
Mode  
Input  
Screen-Control  
White  
Raster  
(APL  
Black  
Raster  
---  
CH o /  
p
RF  
CH o /  
buttons  
p
Screen  
RF  
buttons  
Tape  
M. EQ.  
Spec.  
100%)  
Pattern  
Generator  
See Reference  
Notes below.  
Tape  
M. EQ.  
Spec.  
---  
Pattern  
Generator,  
Figure  
---  
See below  
Color analyzer  
PATTERN GENERATOR  
Figure  
Fig. 2  
Color Analyzer  
EXT. INPUT  
Fig. 3  
Note: Screen Control FBT --- Main CBA  
F.B.T= Fly Back Transformer  
Use service remote control unit  
1. Degauss the CRT and allow CRT to operate for 20  
minutes before starting the alignment.  
Note: Use service remote control unit  
1. Operate the unit more than 20 minutes.  
2. Face the unit to east. Degauss the CRT using De-  
gaussing Coil.  
3. Input the White Raster (APL 100%).  
2. Input the Black Raster Signal from RF Input.  
3. Enter the Service mode. (See page 5-1)  
4. Press "VOL p" button on the service remote con-  
trol unit and select "C/D" mode. (Display changes  
"C/D," "7F," "LANGUAGE," "ACCESS CODE,"  
"SOUND TYPE," "VIDEO TONE," "FM MODE,"  
"V-OUT," "VIDEO," "AV MEMO," "STABLE  
SOUND," "FILTER," "500," and "YUV MEMORY"  
cyclically when "VOL p button is pressed.) then  
press "1." The display will momentarily show "CUT  
OFF R" (R= Red). Now there should be a horizon-  
tal line across the center of the picture tube. If  
needed gradually turn the screen control on the fly-  
back, clockwise until the horizontal line appears.  
Adjust the Red Cut off by pressing the "CH o/p"  
buttons. Proceed to Step 5 when the Red Cut off  
adjustment is done.  
4. Set the color analyzer to the CHROMA mode and  
after zero point calibration, bring the optical recep-  
tor to the center on the tube surface (CRT).  
5. Enter the Service mode. Press "VOL p" button on the  
service remote control unit and select "C/D" mode.  
(Display changes "C/D," "7F," "LANGUAGE," "AC-  
CESS CODE," "SOUND TYPE," "VIDEO TONE,"  
"FM MODE," "V-OUT," "VIDEO," "AV MEMO,"  
"STABLE SOUND," "FILTER," "500," and "YUV  
MEMORY" cyclically when "VOL p" button is  
pressed.) then Press No. 8 button on the service re-  
mote control Unit.  
6. Press No. 4 button on the service remote control  
unit for Red adjustment. Press N0. 5 button on the  
service remote control unit for Blue adjustment.  
7. In each color mode, Press "CH o/p" button to adjust  
the values of color.  
5. Press the "2" button. The display will momentarily  
show "CUT OFF G" (G=Green). Adjust the Green  
Cut off by pressing the "CH o/p" buttons. Proceed  
to step 6 when the Green Cut off adjustment is done.  
6. Press the "3" button. The display will momentarily  
show "CUT OFF B" (B=Blue). Adjust the Blue cut  
off by pressing the "CH o/p" buttons. When done  
with steps 4, 5 and 6 the horizontal line should be  
pure white if not, then attempt the Cut off adjust-  
ment again.  
8. Adjusting Red and Blue color so that the temperature  
becomes 9200K (x: 286 / y: 294) 3%.  
9. At this time, Re-check that Horizontal line is white.  
If not, Re-adjust Cut-off Adjustment until the Hori-  
zontal Line becomes pure white.  
10. Turn off and on again to return to normal mode. Re-  
ceive APL 100% white signal and Check Chroma  
temperatures become 9200K (x: 286 / y: 294) 3%.  
Note: Confirm that Cut Off Adj. is correct after this  
adjustment, and attempt Cut Off Adj. if needed.  
5-7  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Adjust the Focus Control on the FBT to obtain  
clear picture.  
18. Sub-Brightness Adjustment  
Purpose: To get proper brightness.  
The following adjustments normally are not  
attempted in the field. Only when replacing the  
CRT then adjust as a preparation.  
Symptom of Misadjustment: If Sub-Brightness is  
incorrect, proper brightness cannot be obtained by  
adjusting the Brightness Control.  
20. Purity Adjustment  
Test Point  
Adj. Point  
CH o /  
buttons  
Mode  
Input  
Purpose: To obtain pure color.  
p
---  
Tape  
---  
RF  
IQW  
Symptom of Misadjustment: If Color Purity Adjust-  
ment is incorrect, large areas of color may not be  
properly displayed.  
M. EQ.  
Spec.  
Pattern  
Generator  
See below  
Test Point  
Adj. Point  
Mode  
Input  
Figure  
Deflection  
Yoke Purity  
Magnet  
Red  
Color  
---  
---  
White  
Tape  
M. EQ.  
Spec.  
Black  
Pattern  
Generator  
---  
See below.  
This bar  
just  
visible  
Figure  
Fig. 4  
Note: IQW Setup level --- 7.5 IRE  
Use service remote control unit  
GREEN  
RED  
BLUE  
1. Enter the Service mode. (See page 5-1)  
Then input IQW signal from RF Input.  
2. Press "MENU" button on the service remote control  
unit and Select "BRT" mode. (Display changes  
"BRT," "CNT," "CLR," "S-CLR," "TNT," "V-TNT," "S-  
TNT," "SHARP," and "S-SRP" cyclically when  
"MENU" button is pressed). Press "CH o/p" buttons  
so that the bar is just visible (See above figure).  
Fig. 5  
1. Set the unit facing east.  
2. Operate the unit for over 30 minutes before adjust-  
ing.  
3. Fully degauss the unit using an external degauss-  
ing coil.  
3. Turn the power off and on again. (Main power but-  
ton on the TV unit.)  
4. Loosen the screw on the Deflection Yoke Clamper  
and pull the Deflection Yoke back away from the  
screen. (See Fig. 6)  
19. Focus Adjustment  
Purpose: Set the optimum Focus.  
5. Loosen the Ring Lock and adjust the Purity Mag-  
nets so that a red field is obtained at the center of  
the screen. Tighten Ring Lock. (See Fig. 5,6)  
Symptom of Misadjustment: If Focus Adjustment is  
incorrect, blurred images are shown on the display.  
Test Point  
Adj. Point  
Focus Control  
M. EQ.  
Mode  
Input  
6. Slowly push the Deflection Yoke toward bell of  
CRT and set it where a uniform red field is ob-  
tained.  
Mono-  
scope  
---  
Tape  
---  
---  
7. Tighten the clamp screw on the Deflection Yoke.  
Spec.  
Pattern  
Generator  
See below  
Note:Focus VR (FBT) - Main CBA,  
FBT=Fly Back Transformer  
1. Operate the unit more than 30 minutes.  
2. Face the unit to the East and Degauss the CRT  
using Degaussing Coil.  
3. Input the Monoscope Pattern.  
5-8  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21. Convergence Adjustment  
Purpose: To obtain proper convergence of red, green  
and blue beams.  
Symptom of Misadjustment: If Convergence Adjust-  
ment is incorrect, the edge of white letters may have  
color edges.  
Test Point  
Adj. Point  
Mode  
Input  
C.P. Magnet  
(RB),  
C.P. Magnet  
(RB-G),  
Dot Pattern  
or  
Crosshatch  
---  
---  
Deflection Yoke  
Tape  
M. EQ.  
Spec.  
Pattern  
Generator  
---  
See below.  
Figures  
CRT  
RB  
RB-G  
PURITY  
COIL  
SCREW  
RING LOCK  
SCREW  
DY WEDGE  
C.P. MAGNET CLAMPER  
C.P. MAGNET  
COIL CLAMPER  
Fig. 6  
DEFLECTION YOKE  
C.B. MAGNET (RB-G)  
RB  
G
RB  
G
Fig. 8  
1. Loosen the Ring Lock and align red with blue dots  
or Crosshatch at the center of the screen by rotat-  
ing (RB) C.P. Magnets. (See Fig. 7)  
2. Align red / blue with green dots at the center of the  
screen by rotating (RB-G) C.P. Magnet. (See Fig. 8)  
3. Paintlock the C.P. Magnets after adjustment.  
4. Remove the DY Wedges and slightly tilt the De-  
flection Yoke horizontally and vertically to obtain  
the best overall convergence.  
5. Fix the Deflection Yoke by carefully inserting the  
DY Wedges between CRT and Deflection Yoke.  
5-9  
L6650EA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BLOCK DIAGRAMS  
System Control Block Diagram  
IC333  
TV MICON/VIDEO  
/AUDIO/CHROMA  
/DEFLECTION  
RCV101  
REMOTE  
SENSOR  
RCV-IN 70  
(NO CONNECTION) CN301  
I2C-OPEN  
SDA  
SCL  
3
5
6
KEY-IN1 66  
KEY-IN2 69  
KEY  
SWITCH  
CN301 is used for  
adjustment at factory  
TO  
INPUT0  
IC151  
(MEMORY)  
IF/VIDEO BLOCK  
CS  
SCL  
SDA  
7
6
5
72 I2C-OPEN  
58 SCL  
56 SDA  
FROM/TO  
AUDIO BLOCK  
SCL  
SDA  
INPUT0 63  
INPUT1 80  
Q141  
FROM  
IF/VIDEO BLOCK  
AFT  
AGC  
73 AFT  
75 AGC  
Q131  
INPUT0  
INPUT1  
TO  
A-O-MUTE 55  
VOLUME 62  
A-MUTE-H 64  
A-O-MUTE  
VOLUME  
A-MUTE-H  
AUDIO BLOCK  
DG-ON-H 74  
+5V CTRL 28  
+5V CTRL2 18  
+8V CTRL 40  
DG-ON-H  
+5V CTRL  
+5V CTRL2  
+8V CTRL  
PROTECT-1  
PROTECT-2  
P-ON-H  
PROTECT-1  
PROTECT-2 FROM/TO  
PROTECT-3  
P-ON-H  
FROM/TO  
POWER  
SUPPLY BLOCK  
P-ON-H 79  
PROTECT-1 68  
PROTECT-2 67  
PROTECT-3 76  
CRT/H.V. BLOCK  
MAIN CBA  
6-1  
6-2  
L6650BLS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IF/Video Block Diagram  
RF/IF SIGNAL  
VIDEO SIGNAL  
AUDIO SIGNAL  
WF1  
IC33 (IF SIGNAL PROCESS)  
MAIN CBA  
TU1  
SF1  
SAW  
CF31  
20  
21  
VIF  
AMP  
VIDEO  
DET  
4.5MHz  
TRAP  
EQ  
IF 11  
5
3
8
1
FILTER  
AMP  
CF32  
AGC  
1
4
5
8
VCO  
AFT  
TO  
4.5MHz  
FILTER  
SIF  
AMP  
10  
7
SIF  
SCL  
SDA  
AUDIO BLOCK  
EXT.CLK  
VCO F/B  
LPF  
Q33  
RF  
AGC  
17  
WF16  
IF AGC DET  
FROM/TO  
SYSTEM  
CONTROL  
BLOCK  
INPUT0  
AGC  
AFT  
AMP  
14  
22  
16  
Q21  
IC333  
TV MICON/VIDEO  
/AUDIO/CHROMA  
/DEFLECTION  
WF2  
11  
14  
JK721  
VIDEO-IN  
(FRONT)  
JK701  
58 SCL  
56 SDA  
32  
VCXO  
16  
VIDEO-IN  
X301  
3.58MHz  
(REAR)  
26  
24  
20  
LUMINANCE  
PROCESS  
CIRCUIT  
WH301A  
RGB MATRIX  
/COLOR CONT  
OSD SW  
CONTRAST  
BRIGHTNESS  
RGB DRIVE  
/CUT OFF  
/H.V. BLK  
LPF  
52  
51  
50  
5
4
3
BLUE  
GREEN  
RED  
TO  
CHROMINANCE  
PROCESS  
CIRCUIT  
CRT/H.V. BLOCK  
WH301B  
29  
30  
CHROMA COMB  
BASEBAND TINT  
Q951  
JK711  
OSD  
S-VIDEO-IN  
H-SYNC  
PROCESS  
CIRCUIT  
Q956  
53  
46  
45  
38  
37  
ACL  
H-DRIVE  
FBP  
RAMP-OUT  
V-RAMP-F/B  
C
Y
FROM/TO  
CRT/H.V. BLOCK  
V-SYNC  
PROCESS  
CIRCUIT  
61 S-SW  
6-3  
6-4  
L6650BLIF  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Block Diagram  
AUDIO SIGNAL  
IC431 (MTS/SAP AUDIO SIGNAL PROCESS)  
MAIN CBA  
FROM  
IF/VIDEO BLOCK  
L-CH  
30  
STEREO  
FILTER  
L+R  
FILTER  
75uS  
DE-EMPH  
OFFSET  
CANCEL  
SIF  
21  
VCA  
OFFSET  
CANCEL  
MATRIX  
AGC  
L-R  
FILTER  
R-CH  
29  
WIDE BAND  
FILTER  
WIDE BAND  
RMS DET  
WIDE BAND  
EXPAND  
OFFSET  
CANCEL  
(L-R)/SAP  
SW  
SAP  
FILTER  
SAP  
DEMOD  
SAP OUT  
FILTER  
dBX  
DE-EMPH  
SPECTRAL  
EXPAND  
24  
27  
I2C  
DECORDER  
SPECTRAL  
FILTER  
SPECTRAL  
RMS DET  
IC771 (INPUT SELECT)  
IC801 (AUDIO AMP)  
WF6  
TUNER  
REAR  
11  
15  
12  
CN801  
DC  
VOL.  
SP801  
SPEAKER  
L-CH  
13  
5
2
7
SP-L  
1
2
FRONT  
SP-GND  
(L-CH)  
CN802  
SP-R  
DC  
VOL.  
SP802  
SPEAKER  
R-CH  
12  
1
2
SP-GND  
JK702  
AUDIO-IN(L)  
(REAR)  
(R-CH)  
TUNER  
6
4
2
1
REAR  
JK703  
AUDIO-IN(R)  
(REAR)  
3
FRONT  
SW CTL  
10  
JK722  
AUDIO-IN(L)  
(FRONT)  
9
Q825  
JK723  
AUDIO-IN(R)  
(FRONT)  
Q761  
AMP  
JK702  
AUDIO-OUT(L)  
(REAR)  
Q751  
AMP  
JK703  
A-MUTE-H  
VOLUME  
A-O-MUTE  
INPUT 0  
INPUT 1  
SCL  
AUDIO-OUT(R)  
(REAR)  
Q794  
Q792  
Q791  
Q793  
+8V  
FROM/TO  
SYSTEM CONTROL  
BLOCK  
SDA  
6-5  
6-6  
L6650BLA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CRT/H.V. Block Diagram  
VIDEO SIGNAL  
MAIN CBA  
IC551 (V-DEFLECTION CONTROL)  
THERMAL  
PROTECTION  
WF12  
WF9  
DY551 D.Y.  
WF11  
5
4
3
1
V-  
DRIVE  
RAMP-OUT  
P-ON-H  
7
1
AMP  
6
5
Q531  
(SWITCHING)  
PULSE  
UP  
H-  
DRIVE  
V-RAMP-F/B  
Q551, H.  
Q552 CONTROL  
FROM/TO  
3
IF/VIDEO BLOCK  
CN551  
Q561  
(SWITCHING)  
WF7  
WF8  
Q533  
SWITCHING  
P-ON-ON  
Q572  
H.DRIVE  
Q571  
T572  
VR561  
PCC  
VR562  
WIDTH  
H-DRIVE  
PROTECT-1  
PROTECT-2  
H.OUTPUT  
Q547  
(SWITCHING)  
FROM POWER  
SUPPLY BLOCK  
DEF+B  
+B  
T571 F.B.T.  
FOCUS VR  
HV  
ANODE  
F
S
X-RAY CHECK  
FOCUS  
TP591  
TP592  
1
3
5
11  
SCREEN  
8
10  
7
ANODE  
SCREEN VR  
4
9
6
TP302  
15kHz  
WH501A  
WH501B  
WF10  
3
1
HEATER  
+200V  
3
PROTECT-3  
FBP  
1
FROM/TO  
SYSTEM CONTROL  
BLOCK  
ACL  
JK1501  
FOCUS  
SCREEN  
GND  
WF3  
Q1511,  
Q1512  
WF15  
WF4  
WF14  
TO WH301A WH301B  
Q1521,  
Q1522  
RED  
GREEN  
BLUE  
3
4
5
RED AMP  
FROM  
IF/VIDEO BLOCK  
R
G
B
V501  
CRT  
GREEN AMP  
BLUE AMP  
Q1531,  
Q1532  
WF5  
WF13  
HEATER  
TP500  
GND  
TP501  
BLUE  
CN1501  
GND  
CRT CBA  
6-7  
6-8  
L6650BLCRT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power Supply Block Diagram  
CAUTION !  
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.  
If Main Fuse (F601) is blown, check to see that all components in the power supply  
circuit are not defective before you connect the AC plug to the AC power supply.  
Otherwise it may cause some components in the power supply circuit to fail.  
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,  
REPLACE ONLY WITH SAME TYPE 4 A, 125V FUSE.  
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE 4A, 125V.  
NOTE :  
The voltage for parts in hot circuit is measured using  
hot GND as a common terminal.  
4A/125V  
HOT CIRCUIT. BE CAREFUL.  
HOT  
COLD  
T601  
4A/125V  
DEF +B  
F601  
4A/125V  
L601  
D605 - D608  
TP601  
+B  
PROTECT-2  
(TO PIN 67 OF IC333)  
LINE  
FILTER  
BRIDGE  
RECTIFIER  
6
9
+B  
AC601  
AC CORD  
AL+33V  
BACK-UP  
Q111  
CN691  
Q672  
+5V  
L691  
DEGAUSSING  
10  
P-ON+5V  
SWITCHING  
SWITCHING  
COIL  
+5V CTRL2  
PS691  
Q851  
(FROM PIN 18 OF IC333)  
Q321  
+9V  
REGULATOR  
Q961  
+5V  
REGULATOR  
+9V  
SWITCHING  
AL+9V  
4
11  
12  
Q673  
SWITCHING  
CONTROL  
AL+12V  
P-ON+5V  
Q601  
Q681  
+8V  
SWITCHING  
2
1
14  
13  
P-ON+8V  
SWITCHING  
+8V CTRL  
(FROM PIN40 OF IC333)  
Q602  
LIMITER  
Q682  
+5V  
SWITCHING  
P-ON+5V  
+5V CTRL  
(FROM PIN28 OF IC333)  
Q683  
+5V  
SWITCHING  
4
3
1
2
PROTECT-1  
IC601  
(TO PIN68 OF IC333)  
Q831  
SWITCHING  
P-ON-ON  
ERROR  
VR661  
VOLTAGE DET  
+B ADJ  
Q652  
P-ON+12V  
Q841  
(SWITCHING)  
FEED  
BACK  
RL601  
Q191  
SWITCHING  
P-ON-ON  
Q674  
SWITCHING  
P-ON-ON  
P-ON-H  
(FROM PIN79 OF IC333)  
DG-ON-H  
(FROM PIN74 OF IC333)  
Q832  
SWITCHING  
P-ON-ON  
Q696  
SWITCHING  
DG-ON-ON  
MAIN CBA  
6-9  
6-10  
L6650BLP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS  
Standard Notes  
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often  
pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement compo-  
nents rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are  
identified in this manual and its supplements; electrical components having such features are identified by the  
mark " # " in the schematic diagram and the parts list. Before replacing any of these components, read the parts  
list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteris-  
tics as specified in the parts list may create shock, fire, or other hazards.  
Note:  
1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the  
parts list, and may be slightly different or amended since these drawings were prepared.  
2. All resistance values are indicated in ohms (K=103, M=106).  
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.  
4. All capacitance values are indicated in µF (P=10-6µF).  
5. All voltages are DC voltages unless otherwise specified.  
Note of Capacitors:  
ML --- Mylar Cap. PP --- Metallized Film Cap. SC --- Semiconductor Cap. L --- Low Leakage type  
Temperature Characteristics of Capacitors are noted with the following:  
B --- 10% CH --- 0 60ppm/°C CSL --- +350~-1000ppm/°C  
Tolerance of Capacitors are noted with the following:  
Z --- +80~-20%  
Note of Resistors:  
CEM --- Cement Res. MTL --- Metal Res. F --- Fuse Res.  
Capacitors and transistors are represented by the following symbols.  
CBA Symbols  
Schematic Diagram Symbols  
(Top View) (Bottom View)  
Digital Transistor  
+
Electrolytic Capacitor  
(Bottom View)  
Transistor or Digital Transistor  
E
C
B
(Top View)  
(Top View)  
NPN Transistor  
PNP Transistor  
E C B  
E C B  
(Top View)  
(Top View)  
PNP Digital Transistor  
NPN Digital Transistor  
E C B  
E C B  
7-1  
L13SC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON  
THE FOLLOWING PAGES:  
1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME  
TYPE_A,_V FUSE.  
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.  
2. CAUTION:  
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.  
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective  
before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the pow-  
er supply circuit to fail.  
3. Note:  
(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the  
parts list, and may be slightly different or amended since the drawings were prepared.  
(2) To maintain original function and reliability of repaired units, use only original replacement parts which are  
listed with their part numbers in the parts list section of the service manual.  
4. Wire Connectors  
(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).  
(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).  
5. Note: Mark "I" is a leadless (chip) component.  
6. Voltage indications on the schematics are as shown below:  
Plug the TV power cord into a standard AC outlet.:  
1
5.0  
(3.0)  
2
3
Power on mode  
Power off mode  
5.0  
(3.0)  
Voltage  
Unit: Volts  
Indicates that the voltage  
is not consistent here.  
7. How to read converged lines  
1-D3  
Distinction Area  
Line Number  
(1 to 3 digits)  
3
1-B1  
AREA D3  
AREA B1  
2
1
Examples:  
1. "1-D3" means that line number "1" goes to area "D3".  
1-D3  
B
2. "1-B1" means that line number "1" goes to area "B1".  
A
C
D
8. Test Point Information  
: Indicates a test point with a jumper wire across a hole in the PCB.  
: Used to indicate a test point with a component lead on foil side.  
: Used to indicate a test point with no test pin.  
: Used to indicate a test point with a test pin.  
7-2  
L13SC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main 1/4 Schematic Diagram  
VIDEO SIGNAL  
B4  
B3  
B2  
A4  
C4  
C3  
C2  
C1  
D4  
E4  
E3  
E2  
E1  
F4  
F3  
F2  
F1  
MAIN 1/4  
Ref No.  
Position  
ICS  
A-3  
C-2  
IC151  
IC333  
TRANSISTORS  
Q111  
D-1  
A-3  
A-4  
B-4  
E-2  
Q131  
Q141  
Q191  
Q321  
A3  
A2  
A1  
D3  
D2  
D1  
CONNECTOR  
CN301  
A-3  
B1  
L6650SCM1  
7-3  
7-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main 2/4 Schematic Diagram  
VIDEO SIGNAL  
AUDIO SIGNAL  
G4  
K4  
I4  
J4  
H4  
L4  
MAIN 2/4  
Ref No.  
Position  
ICS  
G-3  
H-2  
J-4  
IC431  
IC771  
IC801  
TRANSISTORS  
J-2  
J-2  
J-1  
I-2  
Q751  
Q761  
Q791  
Q792  
Q793  
Q794  
Q825  
Q831  
Q832  
Q841  
Q851  
G3  
G2  
L3  
L2  
L1  
I3  
I2  
J3  
J2  
K3  
K2  
H3  
H2  
I-1  
H-1  
J-3  
K-3  
K-3  
K-3  
J-3  
H-1  
H-1  
J-3  
Q951  
Q956  
Q961  
CONNECTORS  
CN801  
CN802  
L-4  
L-3  
G1  
I1  
J1  
H1  
K1  
L6650SCM2  
7-5  
7-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main 3/4 Schematic Diagram  
CAUTION !  
IF SIGNAL  
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK  
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.  
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE  
MÊME TYPE DE 4A, 125V.  
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.  
If Main Fuse (F601) is blown, check to see that all components in the power supply  
circuit are not defective before you connect the AC plug to the AC power supply.  
Otherwise it may cause some components in the power supply circuit to fail.  
NOTE :  
VIDEO SIGNAL  
AUDIO SIGNAL  
The voltage for parts in hot circuit is measured  
using hot GND as a common terminal.  
4A/125V  
M4  
Q4  
O4  
P4  
N4  
R4  
MAIN 3/4  
Ref No.  
Position  
ICS  
IC33  
P-3  
O-1  
IC601  
TRANSISTORS  
Q21  
P-4  
P-4  
P-2  
P-1  
O-1  
N-2  
N-1  
N-1  
M-2  
M-1  
M-1  
O-2  
Q33  
Q601  
Q602  
Q652  
Q672  
Q673  
Q674  
Q681  
Q682  
Q683  
Q696  
M3  
M2  
R3  
R2  
R1  
O3  
O2  
P3  
P2  
Q3  
Q2  
N3  
N2  
CONNECTOR  
CN691  
Q-2  
TEST POINTS  
N-4  
N-4  
TP300  
TP301  
VARIABLE RESISTOR  
VR661  
O-1  
M1  
O1  
P1  
N1  
Q1  
L6650SCM3  
7-7  
7-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main 4/4 & CRT Schematic Diagram  
CRT  
Ref No.  
TRANSISTORS  
MAIN 4/4  
Position  
Ref No.  
Position  
S-3  
Ref No.  
Position  
Ref No.  
Position  
IC  
TRANSISTORS  
TEST POINTS  
W-1  
W-2  
W-1  
W-2  
W-1  
W-2  
Q1511  
Q1512  
Q1521  
Q1522  
Q1531  
Q1532  
U-2  
T-2  
U-2  
U-2  
U-2  
IC551  
TRANSISTORS  
Q571  
Q572  
CONNECTORS  
TP591  
TP592  
TP601  
S-2  
S-2  
U-2  
T-3  
T-3  
U-3  
Q531  
Q533  
Q547  
Q551  
T-3  
V-2  
V-3  
VARIABLE RESISTORS  
CN571  
WH301A  
WH501A  
VR561  
VR562  
U-3  
U-3  
CONNECTORS  
TEST POINTS  
Q552  
Q561  
CN1501  
X-2  
V-2  
V-3  
TP302  
V-2  
WH301B  
WH501B  
VIDEO SIGNAL  
TEST POINTS  
W-1  
W-2  
TP500  
TP501  
W3  
W2  
W1  
S3  
S2  
U3  
V3  
X3  
T3  
T2  
U2  
U1  
V2  
V1  
X2  
X1  
S1  
T1  
L6650SCM4  
7-9  
7-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main CBA Top View  
CAUTION !  
BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER  
SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.  
ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASETHE INPUT  
SLOWLY,WHENTROUBLESHOOTING THISTYPE POWER SUPPLY  
CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.  
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK  
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.  
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE  
MÊME TYPE DE 4A, 125V.  
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.  
If Main Fuse (F601) is blown, check to see that all components in the power  
supply circuit are not defective before you connect the AC plug to the AC power supply.  
Otherwise it may cause some components in the power supply circuit to fail.  
4A/125V  
MAIN CBA  
NOTE :  
Ref No.  
Position  
Ref No.  
Position  
The voltage for parts in hot circuit is measured  
using hot GND as a common terminal.  
ICS  
TRANSISTORS  
B-2  
E-5  
F-5  
A-1  
C-2  
C-4  
D-1  
E-2  
C-1  
C-1  
C-1  
C-1  
D-1  
D-1  
E-2  
E-3  
F-3  
F-2  
E-3  
D-1  
D-1  
C-1  
IC33  
IC151  
IC333  
IC431  
IC551  
IC601  
IC771  
IC801  
Q751  
Q761  
Q791  
Q792  
Q793  
Q794  
Q825  
Q831  
Q832  
Q841  
Q851  
Q951  
Q956  
Q961  
TP601  
+B  
FOCUS-VR  
(UPPER SIDE)  
TRANSISTORS  
Q21  
C-1  
C-1  
F-3  
F-4  
E-5  
F-5  
E-3  
C-2  
C-2  
B-2  
B-2  
B-2  
B-2  
B-4  
C-2  
B-1  
B-4  
D-4  
D-3  
D-3  
D-3  
D-3  
D-4  
D-4  
D-4  
Q33  
SCREEN-VR  
(LOWER SIDE)  
Q111  
Q131  
Q141  
Q191  
Q321  
Q531  
Q533  
Q547  
TP300  
GND  
CONNECTORS  
A-1  
B-3  
D-5  
E-2  
E-5  
D-4  
A-4  
CN301  
CN571  
CN691  
CN801  
Q551  
Q552  
Q561  
Q571  
Q572  
Q601  
Q602  
Q652  
Q672  
Q673  
Q674  
Q681  
Q682  
Q683  
Q696  
CN802  
WH301A  
WH501A  
TP302  
15kHz  
TEST POINTS  
A-4  
A-2  
A-4  
A-3  
A-3  
B-5  
TP300  
TP301  
TP302  
TP591  
TP592  
TP601  
VARIABLE RESISTOR  
B-2  
B-2  
B-2  
VR561  
VR562  
VR661  
VR661  
+B ADJ  
VR561  
PCC  
VR562  
WIDTH  
TP301  
AGC  
BL6650F01011-1  
7-11  
7-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main CBA Bottom View  
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK  
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.  
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE  
MÊME TYPE DE 4A, 125V.  
CAUTION !  
BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER  
SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.  
ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT  
SLOWLY,WHENTROUBLESHOOTING THISTYPE POWER SUPPLY  
CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.  
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.  
If Main Fuse (F601) is blown, check to see that all components in the power supply  
circuit are not defective before you connect the AC plug to the AC power supply.  
Otherwise it may cause some components in the power supply circuit to fail.  
4A/125V  
NOTE :  
The voltage for parts in hot circuit is measured  
using hot GND as a common terminal.  
WF8  
Q571  
Base  
WF10  
WF2  
PIN 3  
OF WH501A  
PIN 14  
OF IC333  
WF9  
PIN 1  
OF CN571  
WF12  
PIN 4  
OF CN571  
WF11  
PIN 7  
OF IC551  
WF7  
Q572  
Collector  
WF16  
PIN 8  
OF TU1  
WF1  
PIN 3  
OF IC33  
WF6  
PIN 5  
OF IC801  
BL6650F01011-1  
7-13  
7-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CRT CBA Top View  
CRT CBA Bottom View  
CRT CBA  
Ref No.  
Position  
TRANSISTORS  
Q1511  
Q1512  
Q1521  
Q1522  
Q1531  
Q1532  
C-1  
C-1  
C-1  
C-1  
B-1  
B-1  
CONNECTORS  
CN1501  
WH301B  
WH501B  
A-2  
B-2  
A-2  
TEST POINTS  
TP500  
TP501  
B-2  
B-2  
WF15  
WF3  
WF4  
WF14  
WF5  
Q1531 Q1531  
Base Collector  
WF13  
Q1511  
Collector  
Q1511  
Base  
Q1521  
Base  
Q1521  
Collector  
TP501  
BLUE  
TP500  
GND  
7-15  
BL6650F01011-2  
7-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WAVEFORMS  
Input:  
NTSC Color Bar Signal (with 1kHz Audio Signal)  
INITIAL POSITION: Unplug unit from AC outlet for at least 5 minutes.  
reconnect to AC outlet and then turn power on.  
(Brightness---Center Color---Center Tint --- Center Contrast---Approx 70%)  
WF1 ~ WF16 = Waveforms to be observed at  
Waveform check points.  
(Shown in Schematic Diagram.)  
GND  
GND  
GND  
WF1 1DIV: 0.5V 20µsec  
WF5 1DIV: 2V 20µsec  
WF9 1DIV: 200V 20µsec  
WF13 1DIV: 20V 20µsec  
IC 33 Pin 3  
Q 1531 Base  
CN 571 Pin 1  
Q 1531 Collector  
GND  
WF2 1DIV: 0.5V 20µsec  
WF6 1DIV: 0.2V 20msec  
WF10 1DIV: 5V 20µsec  
WF14 1DIV: 20V 20µsec  
IC 333 Pin 14  
IC 801 Pin 5  
WH501A Pin 3  
Q 1521 Collector  
GND  
GND  
1DIV: 2V 20µsec  
WF7 1DIV: 10V 20µsec  
WF3  
WF11 1DIV: 2V 5msec  
WF15 1DIV: 20V 20µsec  
Q 1511 Base  
Q 572 Collector  
IC 551 Pin 7  
Q 1511 Collector  
GND  
8-1  
10 V  
5 ms  
WF12 1DIV: 10V 5msec  
WF8  
1DIV: 5V 20µsec  
WF16 1DIV: 0.2V 20µsec  
WF4 1DIV: 2V 20µsec  
CN 571 Pin 4  
Q 571 Base  
TU 1 Pin 8  
Q 1521 Base  
8-2  
L6650WF  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING DIAGRAM  
CN801  
SP-L  
SP-GND  
CLN801  
1
2
SP801  
SPEAKER  
L-CH  
CN802  
SP-R  
SP-GND  
CLN802  
1
2
SP802  
SPEAKER  
R-CH  
ANODE  
TU1 TUNER UNIT  
V501  
CRT  
MAIN CBA  
BL6650F01011-1  
CN691  
1
2
GND  
FOCUS  
CN1501  
T571  
FBT  
SCREEN  
WH301B  
BLUE  
GREEN  
RED  
WH301A  
BLUE  
GREEN  
RED  
CLN301  
5
4
3
2
1
5
4
3
2
1
GND  
+8V  
GND  
+8V  
WH501B  
HEATER  
GND  
WH501A  
HEATER  
GND  
CLN501  
CRT CBA  
BL6650F01011-2  
3
2
1
3
2
1
+200V  
+200V  
(NO CONNECTION)  
CN301  
DY551  
D.Y.  
1
2
3
4
5
6
INT-MONI  
AGC  
CN571  
1
2
3
4
5
I2C-OPEN  
GND  
HD  
SDA  
SCL  
VD  
CN301 IS USED FOR  
ADJUSTMENT AT  
FACTORY.  
AC601  
9-1  
L6650WI  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IC PIN FUNCTIONS  
IC333 (TV Micro Computer)  
Pin  
No.  
Signal Name  
Function  
Pin  
No.  
Signal Name  
GND  
Function  
35 N.U.  
Not Used  
Not Used  
36 N.U.  
1
2
3
4
5
6
7
8
9
GND  
37 V RAMP F/B  
38 V RAMP OUT  
39 V RAMP CAP  
V Ramp Feed Back  
Vertical Output  
N.U.  
N.U.  
N.U.  
GND  
VCC  
N.U.  
FILT  
HLF  
Not Used  
Not Used  
Not Used  
GND  
V Ramp OSC Capacitor  
40 8.7 VREG OUT DC 8.7V Output  
41 N.U.  
Not Used  
AL+5V  
Not Used  
FILT  
42 H VCO F/B  
43 AFC FILT  
44 GND  
H Vco Feed Back  
Horizontal AFC Filter  
GND  
Filter for CCD  
VHOLD  
45 FBP IN  
46 H-OUT  
47 VCC  
Flyback Pulse Input  
H Pulse Output  
Vcc  
10 VHOLD  
11 CVIN  
Input for Video Signal  
RESET  
12 RESET  
48 VCC  
Vcc  
MCU RESET  
OUT  
13  
RESET Signal Output  
49 VCC  
Vcc  
14 Y-SW OUT  
15 GND  
Composite Signal Output  
GND  
50 R OUT  
51 G OUT  
52 B OUT  
53 ACL  
Red Output  
Green Output  
Blue Output  
IB-Input  
16 3.58 X'TAL  
17 C-APC  
3.58MHz Crystal  
CHROMINANCE APC  
MCU 5.7REG  
OUT  
Micro controller Control  
Voltage Output  
54 N.U.  
Not Used  
18  
55 A-O-MUTE  
Mute Signal of Audio Output  
19 N.U.  
Not Used  
I2C-BUS Controller Interface  
(Data)  
56 SDA  
57 N.U.  
58 SCL  
20 CVBS IN 3  
21 N.U.  
Composite Signal Input 3  
Not Used  
Not Used  
22 VCC  
VCC  
I2C-BUS Controller Interface  
(Clock)  
23 N.U.  
(GND)  
59 N.U.  
60 N.U.  
(GND)  
24 CVBS IN2  
25 N.U.  
Composite Signal Input 2  
Not Used  
Not Used  
Detecting S-VIDEO Jack  
Connection  
26 CVBS IN1  
27 N.U.  
Composite Signal Input 1  
Not Used  
61 S-SW  
62 VOLUME  
63 INPUTO  
64 A-MUTE-H  
65 N.U.  
Volume  
28 5.7V REG OUT 5.7V Output  
Input Select 0  
29 C(Y/C) IN  
30 Y(Y/C) IN  
31 V REG VCC  
32 FSC OUT  
Chrominance Signal Input  
Audio Mute  
Luminance Signal Input  
DC 8.7V Input  
Not Used  
66 KEY-IN 1  
67 PROTECT-2  
68 PROTECT-1  
69 KEY-IN 2  
Key Input 1 (Main)  
Power Supply Protection  
Power Supply Protection  
Key Input 2 (Main)  
Clock Output 3.58MHz  
33 MONITOR OUT Monitor Out  
34 N.U. Not Used  
10-1  
L6650PIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin  
No.  
Signal Name  
Function  
70 RCV-IN  
71 N.U.  
Input For Remote Control  
Not Used  
White Balance Adjustment  
Judgement  
72 I2C OPEN  
73 AFT  
AFT Voltage Input  
Degaussing Coil Control  
AGC Voltage Input  
Power Supply Protection  
Not Used  
74 DG-ON-H  
75 AGC  
76 PROTECT 3  
77 N.U.  
78 FM-SW  
79 P-ON-H  
80 INPUT 1  
Switching IF IC VCO  
Output for P-ON-H  
Input Select 1  
10-2  
L6650PIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLODED VIEWS  
Cabinet  
SHINWHA  
TAPE SGT-730  
(BLACK)  
L2  
V501-1  
L2  
A5  
L2  
Details for DY551  
and surrounding parts  
SHINWHA  
TAPE SGT-730  
(WHITE)  
DY551  
L4  
L3  
L2  
V501-2  
B2  
B5  
Lead Clamper  
Lead  
Clamper  
CLN551  
DY551  
L2  
A6  
B2  
L2  
CRT CBA  
L691  
L2  
B2  
B5  
Lead  
Clamper  
B1  
A4  
L-1  
Lead Clamper  
B-8  
L-1  
B-7  
L-1  
Lead  
B-6  
Lead  
Clamper  
Scotch Tape #880  
L-1  
Clamper  
L1  
B4  
V501  
SP801  
L-1  
B-9  
SP802  
B2  
L1  
B4  
PB6  
MAIN CBA  
PB6  
AC601  
A3  
A2  
A1  
11-1  
11-2  
L6650CEX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing  
X3  
X4  
X2  
S2  
S6  
POP LABEL  
TAPE  
S2  
X1  
S4  
S1  
PACKING TAPE  
S3  
FRONT  
S5  
11-3  
L6250PEX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MECHANICAL PARTS LIST  
PRODUCT SAFETY NOTE: Products marked with a  
Ref. No.  
Description  
DRY BATTERY R6P/2S or  
Part No.  
# have special characteristics important to safety.  
Before replacing any of these components, read care-  
fully the product safety notice in this service manual.  
Don't degrade the safety of the product through  
improper servicing.  
XB0M451T0001  
XB0M451MS002  
XB0M451HU002  
XB0M451HU003  
DRY BATTERY(SUNRISE) R6SSE/2S or  
DRY BATTERY R6P(AR)2PX or  
DRY BATTERY R6P(AR)2P X ICI  
NOTE:  
Table 1 (V501 and DY551 Combination)  
Parts that are not assigned part numbers (---------) are  
not available.  
Note 1: Purity and Convergence Adjustments must be  
performed following CRT replacement. Refer to Electri-  
cal Adjustment Instructions.  
Ref. No.  
Description  
FRONT CABINET L6250UA  
Part No.  
0EM000625  
Note 2: Please confirm CRT Type No. on the CRT  
Warning Label which is located on the CRT. Then See  
the Table 1 for V501 and DY551 combination chart.  
Please refer this CRT, Deflection Yoke combination  
chart for parts order.  
A1  
A2  
CONTROL PLATE L6250UA  
BRAND PLATE T5307UH:SYLVANIA  
REAR CABINET L6250UA  
0EM201570  
0EM407053  
0EM000681  
----------  
A3  
A4  
A5#  
A6  
RATING LABEL L6650UA  
POP LABEL L6650UA  
----------  
B1  
TENSION SPRING B0080B0:EM40808  
M7 CRT SCREW(D22) T7205UF  
SPEAKER HOLDER L1200UA  
CLOTH 190X15XT0.5  
26WH006  
B2  
0EM406573  
0EM405691  
TS7623  
DY551: Deflection  
V501: CRT Type No. V501: CRT Part No.  
Yoke Part No.  
B4  
B5  
CRT A80QCF340X  
CRT A80QCF340X03  
CRT A80LJF30X11(CT)  
TCRT190GS041  
TCRT190GS042  
TCRT190SEG01  
LLBY00ZGS006  
----------  
CLN551  
L1  
CRT GND WIRE CRT GND WIRE  
SCREW, P-TIGHT 3X12 BIND HEAD+  
SCREW, P-TIGHT 4X18 BIND HEAD +  
SCREW TAPPING M4X14  
WX1L6250-005  
GBMP3120  
GBMP4180  
DBU14140  
GBKP3100  
LLBH00ZTM047  
DSD0808XQ009  
DSD0808XQ008  
----------  
L2  
L3  
L4  
SCREW, P-TIGHT 3X10 BIND HEAD+  
DEGAUSSING COIL F-L1232V  
SPEAKER S08F16-J  
CRT Warning Label Location  
L691#  
SP801  
SP802  
Note:  
SPEAKER S08F26-J  
CRT Type No.  
CRT Warning  
Label  
1. V501 (CRT) HAS COUPLE OF SUBSTITUTIONAL PARTS AND EACH PARTS  
ALSO HAS MATCHING COMBINATION WITH DY551.  
PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.  
2. DY551 (DEFLECTION YOKE) HAS MATCHING COMBINATION WITH V501.  
PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.  
CRT TYPE A  
DY551# DEFLECTION YOKE 6150Z-1050M  
LLBY00ZGS006  
TCRT190GS041  
XM04000BV014  
XV10000T4001  
XV10000D9001  
V501#  
V501-1  
V501-2  
CRT A80QCF340X  
PCM 325LT-022  
WEDGE FT-00110W or  
WEDGE DB25SR  
CRT TYPE B  
CRT A80QCF340X03  
CRT TYPE C  
CRT A80LJF30X11(CT)  
PACKING  
V501#  
TCRT190GS042  
TCRT190SEG01  
CRT  
V501#  
S1  
S2  
S3  
S4  
S5  
S6  
CARTON L6650UA  
0EM407898  
0EM407000  
0EM407001  
0EM403887  
----------  
STYROFOAM TOP ASSEMBLY L6250UA  
STYROFOAM BOTTOM ASSEMBLY L6250UA  
SET SHEET PCEC:003502019816  
SERIAL NO. LABEL L6650UA  
HOLD PAD L6250UA  
0EM407005  
ACCESSORIES  
X1  
POLYETHYLENE BAG F8626B5  
OWNER'S MANUAL L6650UA  
REMOTE CONTROL 130/ERC001/N0147UD  
DRY BATTERY R6P UM3 or  
Z325350  
X2#  
X3  
0EMN02090  
N0147UD  
X4  
XB0M451GH001  
20030303  
12-1  
L6650CA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRICAL PARTS LIST  
PRODUCT SAFETY NOTE: Products marked with a  
Ref. No.  
Description  
Part No.  
# have special characteristics important to safety.  
Before replacing any of these components, read care-  
fully the product safety notice in this service manual.  
Don't degrade the safety of the product through  
improper servicing.  
ELECTROLYTIC CAP. 0.47µF/50V M  
ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
CERAMIC CAP.(AX) B K 1000pF/50V  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
CERAMIC CAP.(AX) B K 1000pF/50V  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
FILM CAP.(P) 0.047µF/50V J or  
CE1JMASDLR47  
CE1JMASTL4R7  
CE1JMASDL4R7  
CCA1JKT0B102  
CDA1EZT0F103  
CE1AMASTL101  
CE1AMASDL101  
CCA1JKT0B102  
CDA1EZT0F103  
CMA1JJS00473  
CA1J473MS029  
CMB1JJS00473  
2250473S  
C49  
C51  
C52  
C53  
NOTES:  
C54  
C55  
C57  
1. Parts that are not assigned part numbers (---------)  
are not available.  
2. Tolerance of Capacitors and Resistors are noted  
with the following symbols.  
FILM CAP.(P) 0.047µF/50V J or  
FILM CAP.(P) 0.047µF/50V J TV or  
MYLAR CAP. 0.047µF/50V K  
C..... 0.25%  
G..... 2%  
D..... 0.5%  
J...... 5%  
F..... 1%  
C58  
FILM CAP.(P) 0.033µF/50V J or  
CMA1JJS00333  
CA1J333MS029  
CMB1JJS00333  
CE1JMASTL100  
CE1JMASDL100  
CE1CMASTL470  
CE1CMASDL470  
CE1JMASTL4R7  
CE1JMASDL4R7  
CDA1EZT0F104  
CMA1JJS00102  
CA1J102MS029  
CMB1JJS00102  
2250102S  
K..... 10%  
Z.....+80/-20%  
FILM CAP.(P) 0.033µF/50V J or  
M..... 20%  
N..... 30%  
FILM CAP.(P) 0.033µF/50V J TV  
C104  
C111  
C112  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 47µF/16V M or  
ELECTROLYTIC CAP. 47µF/16V M  
ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
CERAMIC CAP. F Z 0.1µF/25V  
MMA CBA  
Ref. No.  
Description  
Part No.  
MMA-406 CBA  
0ESA05248  
Consists of the following  
C113  
C114  
MAIN CBA  
CRT CBA  
--------------  
--------------  
FILM CAP.(P) 0.001µF/50V J or  
FILM CAP.(P) 0.001µF/50V J or  
FILM CAP.(P) 0.001µF/50V J TV or  
MYLAR CAP. 0.001µF/50V K  
MAIN CBA  
C115  
ELECTROLYTIC CAP. 0.1µF/50V M or  
ELECTROLYTIC CAP. 0.1µF/50V M  
CERAMIC CAP.(AX) B K 220pF/50V  
CERAMIC CAP.(AX) Y K 0.01µF/16V  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
CERAMIC CAP. F Z 0.1µF/25V  
CE1JMASTLR10  
CE1JMASDLR10  
CCA1JKT0B221  
CDA1CKT0Y103  
CDA1EZT0F103  
CE1AMASTL101  
CE1AMASDL101  
CE1AMASTL101  
CE1AMASDL101  
CDA1EZT0F104  
CDA1EZT0F103  
CDA1EZT0F104  
CCA1JKT0B221  
CCA1JKT0B221  
CA1J121TU008  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CA1J153TU011  
CE1JMASTLR10  
CE1JMASDLR10  
CE1AMASTL101  
CE1AMASDL101  
CE1JMASTLR10  
CE1JMASDLR10  
CE1JMASTLR47  
CE1JMASDLR47  
CE1JMASTL100  
CE1JMASDL100  
Ref. No.  
Description  
Part No.  
C116  
C117  
C119  
C120  
MAIN CBA  
Consists of the following  
------------  
CAPACITORS  
C1  
C2  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
CERAMIC CAP.(AX) F Z 0.01µF/50V  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
PCB JUMPER D0.6-P5.0  
CDA1EZT0F103  
CE1AMASTL101  
CE1AMASDL101  
CE1JMASTL4R7  
CE1JMASDL4R7  
CA1J103TU014  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
JW5.0T  
C122  
C3  
C132  
C133  
C150  
C151  
C152  
C301  
C302  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
CERAMIC CAP. F Z 0.1µF/25V  
C4  
C7  
CERAMIC CAP.(AX) B K 220pF/50V  
CERAMIC CAP.(AX) B K 220pF/50V  
CERAMIC CAP.(AX) CH J 120pF/50V  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
CERAMIC CAP.(AX) B K 0.015µF/50V  
ELECTROLYTIC CAP. 0.1µF/50V M or  
ELECTROLYTIC CAP. 0.1µF/50V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 0.1µF/50V M or  
ELECTROLYTIC CAP. 0.1µF/50V M  
ELECTROLYTIC CAP. 0.47µF/50V M or  
ELECTROLYTIC CAP. 0.47µF/50V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
C30  
C31  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
ELECTROLYTIC CAP. 0.47µF/50V M or  
ELECTROLYTIC CAP. 0.47µF/50V M  
CERAMIC CAP.(AX) CH J 56pF/50V  
CERAMIC CAP.(AX) B K 1000pF/50V  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 0.47µF/50V M or  
CE1AMASTL101  
CE1AMASDL101  
CDA1EZT0F103  
CE1JMASTLR47  
CE1JMASDLR47  
CA1J560TU008  
CCA1JKT0B102  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL100  
CE1JMASDL100  
CE1JMASTLR47  
C32  
C34  
C303  
C305  
C35  
C36  
C37  
C306  
C309  
C322  
C324  
C38  
C41  
20030303  
13-1  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
C325  
C328  
CERAMIC CAP.(AX) SL J 12pF/50V  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
STACKED FILM CAP. 0.47µF/50V J or  
FILM CAP.(P) 0.47µF/50V J  
CCA1JJTSL120  
CE1JMASTL100  
CE1JMASDL100  
CDA1EZT0F103  
CMA1JJS00474  
CA1J474MS029  
CCA1JKT0B102  
CE1JMASTL100  
CE1JMASDL100  
CA1J103TU011  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CA1J103TU011  
CE1AMZNTL222  
CE1AMZNDL222  
CE1AMASTL471  
CE1AMASDL471  
CE1AMASTL471  
CE1AMASDL471  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL3R3  
CE1JMASDL3R3  
CE1JMASTL3R3  
CE1JMASDL3R3  
CA1J104TU014  
CCA1JZT0F104  
CA1J223TU011  
CDA1EZT0F104  
CA1J333TU011  
CE1JMASTL4R7  
CE1JMASDL4R7  
CE1AMASTL101  
CE1AMASDL101  
CE1JMASTL2R2  
CE1JMASDL2R2  
CCA1JKT0B151  
CCA1JKT0B151  
CE1JMASTL2R2  
CE1JMASDL2R2  
CE1JMASTL4R7  
CE1JMASDL4R7  
CDA1CKT0X472  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL4R7  
CE1JMASDL4R7  
CDA1CKT0X472  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL100  
CE1JMASDL100  
CE1JMASTL2R2  
ELECTROLYTIC CAP. 2.2µF/50V M  
ELECTROLYTIC CAP. 0.33µF/50V M or  
ELECTROLYTIC CAP. 0.33µF/50V M  
FILM CAP.(P) 0.1µF/50V J or  
CE1JMASDL2R2  
CE1JMASTLR33  
CE1JMASDLR33  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
C444  
C445  
C329  
C330  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
C331  
C332  
CERAMIC CAP.(AX) B K 1000pF/50V  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
CERAMIC CAP.(AX) B K 0.01µF/50V  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
CERAMIC CAP.(AX) B K 0.01µF/50V  
ELECTROLYTIC CAP. 2200µF/10V M or  
ELECTROLYTIC CAP. 2200µF/10V M  
ELECTROLYTIC CAP. 470µF/10V M or  
ELECTROLYTIC CAP. 470µF/10V M  
ELECTROLYTIC CAP. 470µF/10V M or  
ELECTROLYTIC CAP. 470µF/10V M  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 3.3µF/50V M or  
ELECTROLYTIC CAP. 3.3µF/50V M  
ELECTROLYTIC CAP. 3.3µF/50V M or  
ELECTROLYTIC CAP. 3.3µF/50V M  
CERAMIC CAP.(AX) F Z 0.1µF/50V or  
CERAMIC CAP.(AX) F Z 0.1µF/50V  
CERAMIC CAP.(AX) B K 0.022µF/50V  
CERAMIC CAP. F Z 0.1µF/25V  
C446  
FILM CAP.(P) 0.1µF/50V J or  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
FILM CAP.(P) 0.1µF/50V J or  
C341  
C342  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
C448  
C501  
ELECTROLYTIC CAP. 2.2µF/50V M or  
ELECTROLYTIC CAP. 2.2µF/50V M  
FILM CAP. 0.22µF/50V J or  
CE1JMASTL2R2  
CE1JMASDL2R2  
122Z313S  
C343  
C345  
TF CAP. 0.22µF/50V J  
CT1J224MS045  
CCA1JKT0B102  
CE1GMASTL101  
CE1GMASDL101  
CE1JMASLL2R2  
CE1JMASLH2R2  
CE1GMZNTL102  
CE1GMZNDL102  
CE1GMZADL102  
CE1GMZNTL102  
CE1GMZNDL102  
CE1GMZADL102  
CDA1EZT0F103  
CE1JMASTL100  
CE1JMASDL100  
CE1AMASTL101  
CE1AMASDL101  
CMA1JJS00823  
CA1J823MS029  
CCD3AKD0B681  
CCD3AKP0B681  
CA3A681MR028  
CT2A105MS065  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
C502  
C503  
CERAMIC CAP.(AX) B K 1000pF/50V  
ELECTROLYTIC CAP. 100µF/35V M or  
ELECTROLYTIC CAP. 100µF/35V M  
ELECTROLYTIC CAP. 2.2µF/50V M LL or  
ELECTROLYTIC CAP. 2.2µF/50V LL  
ELECTROLYTIC CAP. 1000µF/35V M or  
ELECTROLYTIC CAP. 1000µF/35V M or  
ELECTROLYTIC CAP. 1000µF/35V M  
ELECTROLYTIC CAP. 1000µF/35V M or  
ELECTROLYTIC CAP. 1000µF/35V M or  
ELECTROLYTIC CAP. 1000µF/35V M  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
FILM CAP.(P) 0.082µF/50V J or  
C347  
C349  
C353  
C504  
C505  
C506  
C401  
C402  
C403  
C508  
C520  
C532  
C541  
C551  
C404  
C405  
C406  
C411  
FILM CAP.(P) 0.082µF/50V J  
CERAMIC CAP.(AX) B K 0.033µF/50V  
ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 2.2µF/50V M or  
ELECTROLYTIC CAP. 2.2µF/50V M  
CERAMIC CAP.(AX) B K 150pF/50V  
CERAMIC CAP.(AX) B K 150pF/50V  
ELECTROLYTIC CAP. 2.2µF/50V M or  
ELECTROLYTIC CAP. 2.2µF/50V M  
ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
CERAMIC CAP.(AX) X K 4700pF/16V  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
CERAMIC CAP.(AX) X K 4700pF/16V  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 2.2µF/50V M or  
CERAMIC CAP. B K 680pF/1KV or  
CERAMIC CAP. B K 680pF/1KV or  
CERAMIC CAP. B K 680pF/1KV  
METALIZED PLYESTER CAP. 1µF/100V J  
FILM CAP.(P) 0.1µF/50V J or  
C413  
C414  
C555  
C556  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
C415  
C416  
C417  
C561  
C562  
ELECTROLYTIC CAP. 47µF/35V M or  
ELECTROLYTIC CAP. 47µF/35V M  
ELECTROLYTIC CAP. 470µF/10V M or  
ELECTROLYTIC CAP. 470µF/10V M  
CE1GMASTL470  
CE1GMASDL470  
CE1AMASTL471  
CE1AMASDL471  
CA2D474VC012  
CT2E474MS041  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
C421  
C563# P. P. C A P 0 . 47 µF/200 J or  
C423  
C424  
#
PP CAP. 0.47µF/250V J  
C565  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
C426  
C567# PP CAP. 0.0018µF/1.6KV J or  
CA3C182VC010  
CT3C182MS039  
CMA1JJS00473  
CA1J473MS029  
CMB1JJS00473  
2250473S  
#
PP CAP. 0.0018µF/1.6KV J  
C428  
C429  
C568  
FILM CAP.(P) 0.047µF/50V J or  
FILM CAP.(P) 0.047µF/50V J or  
FILM CAP.(P) 0.047µF/50V J TV or  
MYLAR CAP. 0.047µF/50V K  
C571# PCB JUMPER D0.6-P10.0  
JW10.0T  
C441  
C442  
C574# ELECTROLYTIC CAP. 22µF/250V M or  
CE2EMZPTL220  
CE2EMZNDL220  
CE1GMASTL470  
#
ELECTROLYTIC CAP. 22µF/250V M  
C577  
ELECTROLYTIC CAP. 47µF/35V M or  
20030303  
13-2  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
ELECTROLYTIC CAP. 47µF/35V M  
FILM CAP.(P) 0.01µF/50V J or  
FILM CAP.(P) 0.01µF/50V J or  
FILM CAP.(P) 0.01µF/50V J TV or  
MYLAR CAP. 0.01µF/50V K  
CE1GMASDL470  
CMA1JJS00103  
CA1J103MS029  
CMB1JJS00103  
2250103S  
ELECTROLYTIC CAP. 100µF/160V M  
CE2CMZPDL101  
CE1GMZNTL222  
CE1GMZNDL222  
CE1CMZNTL102  
CE1CMZNDL102  
CE1CMZADL102  
CDA1EZT0F103  
CE1EMZNTL102  
CE1EMZPDL102  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL100  
CE1JMASDL100  
CE1AMASTL101  
CE1AMASDL101  
CE1AMASTL471  
CE1AMASDL471  
CE1AMASTL102  
CE1AMASDL102  
CE1AMASTL101  
CE1AMASDL101  
CCA1JKT0B101  
JW5.0T  
C578  
C657# ELECTROLYTIC CAP. 2200µF/35V M or  
ELECTROLYTIC CAP. 2200µF/35V M  
C658# ELECTROLYTIC CAP. 1000µF/16V M(VR/HC) or  
#
#
ELECTROLYTIC CAP. 1000µF/16V M or  
ELECTROLYTIC CAP. 1000µF/16V M  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
C580# PP CAP. 0.018µF/1.6KV J or  
PP CAP. 0.018µF/1.6KV J  
C582# P.P. CAPACITOR 0.022µF/630V J or  
CA3C183VC010  
CT3C183MS039  
CBP2KJD00223  
CT2K223KF011  
CBP2KKD00223  
CMA2AJS00104  
CMB2AJS00104  
CE1JMASTL4R7  
CE1JMASDL4R7  
CE2CMZNTL101  
CE2CMZPDL101  
CE1JMASTL100  
CE1JMASDL100  
CCD2JKS0B101  
CT2E104MS037  
CT2E104HJE06  
CT2E104DC011  
CT2E104HJE06  
CCA1JKT0B471  
CCD2JZP0F103  
CCD2EZA0F103  
CCD2JZP0F103  
CCD2EZA0F103  
CCD3DKD0B681  
CCD3DKP0B681  
CE2DMZNTL471  
CE2DMZNDL471  
CA2D471NC013  
CMA1JJS00683  
CA1J683MS029  
CMB1JJS00683  
2250683S  
#
#
C661  
C662# ELECTROLYTIC CAP. 1000µF/25V M or  
#
P.P. CAPACITOR 0.022µF/630V J or  
#
ELECTROLYTIC CAP. 1000µF/25V M  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 470µF/10V M or  
ELECTROLYTIC CAP. 470µF/10V M  
ELECTROLYTIC CAP. 1000µF/10V M or  
ELECTROLYTIC CAP. 1000µF/10V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
CERAMIC CAP.(AX) B K 100pF/50V  
PCB JUMPER D0.6-P5.0  
#
P.P. CAPACITOR 0.022µF/630V J  
C667  
C583# FILM CAP.(P) 0.1µF/100V J or  
FILM CAP.(P) 0.1µF/100V J TV  
C584# ELECTROLYTIC CAP. 4.7µF/50V M or  
ELECTROLYTIC CAP. 4.7µF/50V M  
C588# ELECTROLYTIC CAP. 100µF/160V M W/F or  
ELECTROLYTIC CAP. 100µF/160V M  
C594# ELECTROLYTIC CAP. 10µF/50V M or  
#
#
C681  
C682  
C684  
C685  
C686  
#
#
ELECTROLYTIC CAP. 10µF/50V M  
C596  
CERAMIC CAP. B K 100pF/500V  
C601# METALLIZED FILM CAP. 0.1µF/250V or  
#
METALLIZED FILM CAP. 0.1µF/275V K or  
FILM CAP.(MP) 0.1µF/250V K or  
METALLIZED FILM CAP. 0.1µF/275V K  
CERAMIC CAP.(AX) B K 470pF/50V  
CERAMIC CAP. F Z 0.01µF/500V or  
CERAMIC CAP. 0.01µF/AC250V  
CERAMIC CAP. F Z 0.01µF/500V or  
CERAMIC CAP. 0.01µF/AC250V  
CERAMIC CAP. B K 680pF/2KV or  
CERAMIC CAP. B K 680pF/2KV  
#
#
C603  
C605  
C701  
C702  
C705  
C706  
CERAMIC CAP.(AX) X K 6800pF/16V  
ELECTROLYTIC CAP. 0.47µF/50V M or  
ELECTROLYTIC CAP. 0.47µF/50V M  
CERAMIC CAP.(AX) X K 6800pF/16V  
ELECTROLYTIC CAP. 0.47µF/50V M or  
ELECTROLYTIC CAP. 0.47µF/50V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
CERAMIC CAP.(AX) B K 1000pF/50V  
CERAMIC CAP.(AX) B K 100pF/50V  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
CERAMIC CAP.(AX) X K 6800pF/16V  
ELECTROLYTIC CAP. 0.47µF/50V M  
CERAMIC CAP.(AX) X K 6800pF/16V or  
CERAMIC CAP.(AX) X K 3300pF/16V  
ELECTROLYTIC CAP. 0.47µF/50V M or  
ELECTROLYTIC CAP. 0.47µF/50V M  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 0.1µF/50V M or  
ELECTROLYTIC CAP. 0.1µF/50V M  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 0.1µF/50V M or  
ELECTROLYTIC CAP. 0.1µF/50V M  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 470µF/25V M or  
ELECTROLYTIC CAP. 470µF/25V M  
CDA1CKT0X682  
CE1JMASTLR47  
CE1JMASDLR47  
CDA1CKT0X682  
CE1JMASTLR47  
CE1JMASDLR47  
CE1JMASTL100  
CE1JMASDL100  
CCA1JKT0B102  
CCA1JKT0B101  
CE1JMASTL100  
CE1JMASDL100  
CDA1CKT0X682  
CE1JMASTLR47  
CDA1CKT0X682  
CDA1CKT0X332  
CE1JMASTLR47  
CE1JMASDLR47  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTLR10  
CE1JMASDLR10  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTLR10  
CE1JMASDLR10  
CE1AMASTL101  
CE1AMASDL101  
CE1JMASTL100  
CE1JMASDL100  
CE1EMASTL471  
CE1EMASDL471  
C606  
C609  
C708  
C709  
C610# ELECTROLYTIC CAP. 470µF/200V M or  
#
ELECTROLYTIC CAP. 470µF/200V M or  
ELECTROLYTIC CAP. 470µF/200V  
FILM CAP.(P) 0.068µF/50V J or  
FILM CAP.(P) 0.068µF/50V J or  
FILM CAP.(P) 0.068µF/50V J TV or  
MYLAR CAP. 0.068µF/50V K  
FILM CAP.(P) 0.056µF/50V J or  
FILM CAP.(P) 0.056µF/50V J or  
FILM CAP.(P) 0.056µF/50V J TV or  
MYLAR CAP. 0.056µF/50V KT  
CERAMIC CAP.(AX) B K 100pF/50V  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
C713  
#
C611  
C718  
C721  
C722  
C613  
CMA1JJS00563  
CA1J563MS029  
CMB1JJS00563  
2250563S  
C725  
C726  
C728  
C615  
C616  
CCA1JKT0B101  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
C729  
C751  
C618  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
C757  
C761  
C642# SAFETY CAP. 4700pF/250V or  
CCG2EMA0F472  
CCG2EMP0E472  
CCG2HMN0F472  
CA3D561KG004  
CCD3DKA0B561  
CA3D561PAN04  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE2CMZNTL101  
#
SAFETY CAP. E M 4700pF/250V KH or  
CERAMIC CAP. 0.0047µF F CS  
#
C650  
CERAMIC CAP. LB 560pF/2KV or  
CERAMIC CAP. BN 560pF/2KV or  
CERAMIC CAP. 560pF/2KV  
C767  
C773  
C781  
C801  
C654  
C656  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 100µF/160V M W/F or  
20030303  
13-3  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
C802  
ELECTROLYTIC CAP. 470µF/25V M or  
ELECTROLYTIC CAP. 470µF/25V M  
FILM CAP.(P) 0.1µF/50V J or  
CE1EMASTL471  
CE1EMASDL471  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
D326  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
C803  
C804  
C808  
C809  
FILM CAP.(P) 0.1µF/50V J or  
D351  
D352  
D353  
D501  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
FILM CAP.(P) 0.1µF/50V J or  
CMA1JJS00104  
CA1J104MS029  
CMB1JJS00104  
2250104S  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
FILM CAP.(P) 0.1µF/50V J or  
FILM CAP.(P) 0.1µF/50V J TV or  
MYLAR CAP. 0.1µF/50V K  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M or  
ELECTROLYTIC CAP. 1µF/50V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 22µF/50V M or  
ELECTROLYTIC CAP. 22µF/50V M  
ELECTROLYTIC CAP. 1000µF/25V M or  
ELECTROLYTIC CAP. 1000µF/25V M  
ELECTROLYTIC CAP. 100µF/16V M or  
ELECTROLYTIC CAP. 100µF/16V M  
ELECTROLYTIC CAP. 100µF/25V M or  
ELECTROLYTIC CAP. 100µF/25V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
ELECTROLYTIC CAP. 470µF/16V M or  
ELECTROLYTIC CAP. 470µF/16V M  
CERAMIC CAP.(AX) F Z 0.01µF/25V  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL1R0  
CE1JMASTL010  
CE1JMASDL1R0  
CE1JMASDL010  
CE1JMASTL100  
CE1JMASDL100  
CE1JMASTL220  
CE1JMASDL220  
CE1EMZNTL102  
CE1EMZPDL102  
CE1CMASTL101  
CE1CMASDL101  
CE1EMASTL101  
CE1EMASDL101  
CE1JMASTL100  
CE1JMASDL100  
CE1CMASTL471  
CE1CMASDL471  
CDA1EZT0F103  
CE1JMASTL100  
CE1JMASDL100  
CE1AMASTL101  
CE1AMASDL101  
DIODE FR104-B or  
NDLZ000FR104  
QDPZ0ERA2202  
QDQZ0010ELS2  
QDTB00MTZJ24  
NDTB00DZ24BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
RECTIFIER DIODE ERA22-02 or  
RECTIFIER DIODE 10ELS2  
D502# ZENER DIODE MTZJT-7724B or  
ZENER DIODE DZ-24BSBT265  
D503# SWITCHING DIODE 1SS133(T-77) or  
#
C812  
C814  
C821  
C827  
C831  
C851  
C852  
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
#
D545  
ZENER DIODE MTZJT-776.8B or  
ZENER DIODE DZ-6.8BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTB0MTZJ6R8  
NDTB0DZ6R8BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D546  
D547  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D552# ZENER DIODE MTZJT-773.0B or  
QDTB0MTZJ3R0  
NDTB0DZ3R0BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
ZENER DIODE DZ-3.0BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
D558  
C853  
C963  
D572  
D573  
RECTIFIER DIODE ERA22-02 or  
RECTIFIER DIODE 10ELS2  
RECTIFIER DIODE ERA22-02 or  
RECTIFIER DIODE 10ELS2  
QDPZ0ERA2202  
QDQZ0010ELS2  
QDPZ0ERA2202  
QDQZ0010ELS2  
QDLZ0ERD0715  
QDQZ0ERD3806  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
C964# ELECTROLYTIC CAP. 100µF/10V M or  
#
ELECTROLYTIC CAP. 100µF/10V M  
CONNECTORS  
D580# DIODE ERD07-15  
D582  
D583  
FAST RECOVERY DIODE ERD38-06  
CN301  
CONNECTOR BASE, 6P TUC-P06P-B1  
J3TUA06TG001  
J3TVC05TG002  
J3RTC05JG001  
1730812  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
CN571# CONNECTOR BASE, 5P TV-50P-05-V3 or  
#
#
CONNECTOR BASE, 5P RTB-1.5-5P or  
CONNECTOR BASE, 5P W-P3005-02  
D584# SWITCHING DIODE 1SS133(T-77) or  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
CN691# CONNECTOR BASE, 2P TV-50P-02-V3 or  
J3TVC02TG002  
J3RTC02JG001  
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
#
CONNECTOR BASE, 2P RTB-1.5-2P  
#
CN801  
STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002  
000 or  
D585  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
STRAIGHT PIN HEADER, 2P 173981-2  
1770258  
CN802  
STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002  
000 or  
D591# ZENER DIODE MTZJT-7736B or  
ZENER DIODE DZ-36BSBT265  
D594# SWITCHING DIODE 1SS133(T-77) or  
QDTB00MTZJ36  
NDTB00DZ36BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
STRAIGHT PIN HEADER, 2P 173981-2  
DIODES  
1770258  
#
D131  
D171  
ZENER DIODE MTZJT-775.1B or  
ZENER DIODE DZ-5.1BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTB0MTZJ5R1  
NDTB0DZ5R1BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
#
D597  
ZENER DIODE MTZJT-776.8B or  
ZENER DIODE DZ-6.8BSBT265  
QDTB0MTZJ6R8  
NDTB0DZ6R8BS  
NDLZ001N5406  
NDLZ001N5406  
NDLZ001N5406  
NDLZ001N5406  
QDTZ001SS133  
NDTZ001N4148  
D605# DIODE 1N5406  
D606# DIODE 1N5406  
D607# DIODE 1N5406  
D608# DIODE 1N5406  
D322  
D323  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
ZENER DIODE MTZJT-779.1B or  
ZENER DIODE DZ-9.1BSBT265  
QDTB0MTZJ9R1  
NDTB0DZ9R1BS  
D609  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
20030303  
13-4  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
DIODE 1SS176TPA7  
D611# ZENER DIODE MTZJT-7720B or  
Part No.  
1SS176T  
Ref. No.  
Description  
Part No.  
D826  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
QDTB00MTZJ20  
NDTB00DZ20BS  
QDTB0MTZJ8R2  
NDTB0DZ8R2BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
ZENER DIODE DZ-20BSBT265  
ZENER DIODE MTZJT-778.2B or  
ZENER DIODE DZ-8.2BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
D613  
D827  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D614  
D841# SWITCHING DIODE 1SS133(T-77) or  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
D615  
D621  
SWITCHING DIODE 1N4148 T-77  
BEAD INDUCTORS FBA04HA600VB-00  
QDTZ001N4148  
LLBF00STU026  
QDWZ00030DF6  
QD4Z0ERD2906  
QDLZ00FE2016  
NDLZ000FR154  
QDPZ0ERB4402  
NDLZ000FR154  
QDPZ0ERB4402  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D842# ZENER DIODE MTZJT-776.2B or  
ZENER DIODE DZ-6.2BSBT265  
D851# ZENER DIODE MTZJT-7712B or  
QDTB0MTZJ6R2  
NDTB0DZ6R2BS  
QDTB00MTZJ12  
NDTB00DZ12BS  
QDTB0MTZJ9R1  
NDTB0DZ9R1BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D651# FAST RECOVERY DIODE 30DF6 or  
#
#
#
DIODE ERD29-06J or  
FAST RECOVERY DIODE FE201-6  
#
ZENER DIODE DZ-12BSBT265  
ZENER DIODE MTZJT-779.1B or  
ZENER DIODE DZ-9.1BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
D652# DIODE FR154 or  
D853  
#
FAST RECOVERY DIODE ERB44-02  
D653# DIODE FR154 or  
D854  
D855  
D896  
#
FAST RECOVERY DIODE ERB44-02  
D654# SWITCHING DIODE 1SS133(T-77) or  
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
D655  
ZENER DIODE 1ZB180  
QDQZ001ZB180  
QDTB0MTZJ6R8  
NDTB0DZ6R8BS  
NDLZ000FR154  
QDPZ0ERB4402  
QDQZ0001ZC18  
QDQZ000RD18F  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D656# ZENER DIODE MTZJT-776.8B or  
ZENER DIODE DZ-6.8BSBT265  
D657# DIODE FR154 or  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
#
FAST RECOVERY DIODE ERB44-02  
D963  
D966  
ZENER DIODE MTZJT-775.6B or  
ZENER DIODE DZ-5.6BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTB0MTZJ5R6  
NDTB0DZ5R6BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D658# DIODE 1ZC18 or  
#
ZENER DIODE RD18F  
D660  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
ICS  
D661  
D666  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
IC33  
IC:VIF/SIF DETECTOR M61111FP  
IC:MEMORY AT24C02N-10SC or  
IC(EEPROM) M24C02-MN6 or  
IC:MEMORY BR24C02F-W or  
IC:MEMORY BR24C02F or  
IC:MEMORY S524C20D21 or  
IC(EEP-ROM) M24C02-WMN6  
IC M61272M8-054FP  
QSZBA0SMB010  
NSMMA0SAZ012  
NSMMA0SSS028  
QSMBA0SRM003  
QSMMA0SRM003  
NSZBA0SSM028  
NSZAA0SSS004  
QSZAA0RMB130  
QSZBA0TMS003  
QSZBA0SSY006  
NPEB0LTV817F  
NPEC0LTV817F  
QSZBA0TTS096  
NSZBA0TF3079  
QSZBA0SMS007  
IC151  
ZENER DIODE MTZJT-7736B or  
ZENER DIODE DZ-36BSBT265  
QDTB00MTZJ36  
NDTB00DZ36BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
D671# SWITCHING DIODE 1SS133(T-77) or  
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
#
IC333  
IC431  
D672  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
IC:MTS DECORDER AN5832SA  
IC551# IC:VERTICAL OUTPUT LA78041  
IC601# PHOTOCOUPLER LTV-817B-F or  
D673  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
PHOTOCOUPLER LTV-817C-F  
IC:SWITCHING TC4052BF(EL) or  
IC:SWITCHING CD4052BCSJX  
AUDIO POWER IC AN17805A  
COILS  
IC771  
D675# SWITCHING DIODE 1SS133(T-77) or  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
IC801  
#
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
L1  
L2  
PCB JUMPER D0.6-P5.0  
INDUCTOR 22µH-K-5FT or  
INDUCTOR 22µH-K  
JW5.0T  
D692# SWITCHING DIODE 1SS133(T-77) or  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
LLARKBSTU220  
LLARKDQKA220  
LLAXJATTU150  
LLAXKDTKA150  
LLAXJATTU220  
LLAXKDTKA220  
JW5.0T  
#
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
L32  
L33  
INDUCTOR 15µH-J-26T or  
INDUCTOR 15µH-K-26T  
INDUCTOR 22µH-J-26T or  
INDUCTOR 22µH-K-26T  
PCB JUMPER D0.6-P5.0  
INDUCTOR 100µH-J-5FT or  
INDUCTOR 100µH-K  
D694# ZENER DIODE MTZJT-7715B or  
QDTB00MTZJ15  
NDTB00DZ15BS  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
ZENER DIODE DZ-15BSBT265  
SWITCHING DIODE 1SS133(T-77) or  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
D696  
L34  
L51  
LLARJCSTU101  
LLARKDQKA101  
LLARKBSTU220  
LLARKDQKA220  
LLARKBSTU220  
LLARKDQKA220  
D697# SWITCHING DIODE 1SS133(T-77) or  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
#
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
L111  
L112  
INDUCTOR 22µH-K-5FT or  
INDUCTOR 22µH-K  
D698# SWITCHING DIODE 1SS133(T-77) or  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
INDUCTOR 22µH-K-5FT or  
INDUCTOR 22µH-K  
#
#
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
20030303  
13-5  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
INDUCTOR 100µH-J-5FT or  
Part No.  
Ref. No.  
Description  
Part No.  
2SC3331UZ  
L301  
LLARJCSTU101  
LLARKDQKA101  
JW5.0T  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
INDUCTOR 100µH-K  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
L341  
PCB JUMPER D0.6-P5.0  
PCB JUMPER D0.6-P5.0  
LINEARITY COIL ELH5L6136N  
CHOKE COIL ELC18B681LK or  
CHOKE COIL CSA-LF057  
CHOKE COIL 47µH-K or  
POT COIL 47µH K  
Q533  
L342  
JW5.0T  
TRANSISTOR 2SC2785(H) or  
L551#  
L562#  
#
LLBD00PMS008  
LLC681KMS001  
LLBD00ZSA001  
LLBD00PKV007  
LLBD**DMM001  
LLBG00ZY2009  
LLBG00ZXB004  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
L588  
2SC3331UZ  
L601#  
LINE FILTER MS036 or  
LINE FILTER JLB2808  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
#
Q547  
TRANSISTOR 2SC2785(H) or  
TRANSISTORS  
TRANSISTOR 2SA1175(F) or  
TRANSISTOR 2SC2785(J) or  
Q21  
Q33  
QQSF02SA1175  
NQS10KTA1267  
NQS40KTA1266  
2SA1318TZ  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR KTA1267(GR) or  
TRANSISTOR KTA1266(GR) or  
TRANSISTOR 2SA1318(T)-AANP or  
TRANSISTOR 2SA1318(U)-AANP or  
TRANSISTOR 2SA1015-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
2SC3331UZ  
2SA1318UZ  
QQS102SC1815  
QQSF02SA1175  
NQS10KTA1267  
NQS40KTA1266  
2SA1318TZ  
QQS102SA1015  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
Q551# TRANSISTOR 2SA1175(F) or  
#
#
#
#
#
TRANSISTOR KTA1267(GR) or  
TRANSISTOR KTA1266(GR) or  
TRANSISTOR 2SA1318(T)-AANP or  
TRANSISTOR 2SA1318(U)-AANP or  
TRANSISTOR 2SA1015-GR(TPE2)  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
2SA1318UZ  
QQS102SA1015  
NQ400KTD2059  
NQ4Y0KTD2059  
QQES02SD1666  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
Q552# TRANSISTOR KTD2059(O) or  
2SC3331UZ  
#
TRANSISTOR KTD2059(Y) or  
TRANSISTOR 2SD1666S  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
#
Q111# TRANSISTOR 2SC2785(F) or  
Q561  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
#
TRANSISTOR 2SC2785(H) or  
#
TRANSISTOR 2SC2785(J) or  
#
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
RES. BUILT-IN TRANSISTOR BA1F4M-T or  
RES. BUILT-IN TRANSISTOR KRC103M  
RES. BUILT-IN TRANSISTOR BA1F4M-T or  
RES. BUILT-IN TRANSISTOR KRC103M  
TRANSISTOR 2SC2785(F) or  
#
#
#
2SC3331UZ  
2SC3331UZ  
#
QQS102SC1815  
QQSZ00BA1F4M  
NQSZ0KRC103M  
QQSZ00BA1F4M  
NQSZ0KRC103M  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
QQS102SC1815  
QQWZ02SD2553  
QQWZ02SC5902  
QQSY02SC1627  
QFFZ02SK3407  
QQS002SC2120  
QQSY02SC2120  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
Q131  
Q571# TRANSISTOR 2SD2553 or  
TRANSISTOR 2SC5902  
#
Q141  
Q191  
Q572# TRANSISTOR 2SC1627Y-TPE2  
Q601# FET 2SK3407  
Q602# TRANSISTOR 2SC2120-O-TPE2 or  
TRANSISTOR 2SC2785(H) or  
#
TRANSISTOR 2SC2120-Y(TPE2)  
TRANSISTOR 2SC2785(J) or  
Q652# TRANSISTOR 2SC2785(F) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
#
#
#
#
#
#
#
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
2SC3331UZ  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
Q321  
2SC3331UZ  
TRANSISTOR 2SC2785(H) or  
QQS102SC1815  
Q2SA9500TPE2  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
TRANSISTOR 2SC2785(J) or  
Q672# TRANSISTOR 2SA950(O)  
Q673  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
2SC3331UZ  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
Q531  
TRANSISTOR 2SC2785(H) or  
2SC3331UZ  
TRANSISTOR 2SC2785(J) or  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
Q674  
20030303  
13-6  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
2SC3331TZ  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2120-O-TPE2 or  
TRANSISTOR 2SC2120-Y(TPE2) or  
TRANSISTOR KTC3203(Y)  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
2SC3331UZ  
QQS102SC1815  
QQSS002SB892  
QQST002SB892  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
2SC3331UZ  
Q831# TRANSISTOR 2SB892(S) or  
QQS102SC1815  
QQS002SC2120  
QQSY02SC2120  
NQSY0KTC3203  
QQS002SC2120  
QQSY02SC2120  
NQSY0KTC3203  
QQS002SC2120  
QQSY02SC2120  
NQSY0KTC3203  
QQSZ00BA1F4M  
NQSZ0KRC103M  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
#
TRANSISTOR 2SB892(T)  
Q681  
Q682  
Q683  
Q832  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2120-O-TPE2 or  
TRANSISTOR 2SC2120-Y(TPE2) or  
TRANSISTOR KTC3203(Y)  
TRANSISTOR 2SC2120-O-TPE2 or  
TRANSISTOR 2SC2120-Y(TPE2) or  
TRANSISTOR KTC3203(Y)  
2SC3331UZ  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
Q841  
Q696  
Q751  
RES. BUILT-IN TRANSISTOR BA1F4M-T or  
RES. BUILT-IN TRANSISTOR KRC103M  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
2SC3331UZ  
QQS102SC1815  
QQS002SC2120  
QQSY02SC2120  
NQSY0KTC3203  
QQSF02SA1175  
NQS10KTA1267  
NQS40KTA1266  
2SA1318TZ  
Q851# TRANSISTOR 2SC2120-O-TPE2 or  
2SC3331UZ  
#
TRANSISTOR 2SC2120-Y(TPE2) or  
TRANSISTOR KTC3203(Y)  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
#
Q761  
Q791  
Q792  
Q793  
Q951  
TRANSISTOR 2SA1175(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR KTA1267(GR) or  
TRANSISTOR KTA1266(GR) or  
TRANSISTOR 2SA1318(T)-AANP or  
TRANSISTOR 2SA1318(U)-AANP or  
TRANSISTOR 2SA1015-GR(TPE2)  
TRANSISTOR 2SA1175(F) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
2SA1318UZ  
QQS102SA1015  
QQSF02SA1175  
NQS10KTA1267  
NQS40KTA1266  
2SA1318TZ  
2SC3331UZ  
Q956  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
TRANSISTOR KTA1267(GR) or  
TRANSISTOR KTA1266(GR) or  
TRANSISTOR 2SA1318(T)-AANP or  
TRANSISTOR 2SA1318(U)-AANP or  
TRANSISTOR 2SA1015-GR(TPE2)  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
2SA1318UZ  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC2785(F) or  
QQS102SA1015  
QQS002SC2120  
QQSY02SC2120  
NQSY0KTC3203  
Q961# TRANSISTOR 2SC2120-O-TPE2 or  
#
#
TRANSISTOR 2SC2120-Y(TPE2) or  
TRANSISTOR KTC3203(Y)  
RESISTORS  
2SC3331UZ  
QQS102SC1815  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
R23  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 270 Ω or  
CARBON RES. 1/6W J 270 Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 3.3k Ω  
CARBON RES. 1/4W J 27k Ω  
CARBON RES. 1/4W J 100k Ω  
CARBON RES. 1/4W J 12k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 220k Ω  
CARBON RES. 1/4W J 220k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 1.5k Ω  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0223  
RCX4JATZ0271  
RCX6JATZ0271  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0103  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0332  
RCX4JATZ0273  
RCX4JATZ0104  
RCX4JATZ0123  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0224  
RCX4JATZ0224  
RCX4JATZ0223  
RCX4JATZ0152  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
R31  
R33  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SA1175(F) or  
R34  
2SC3331UZ  
QQS102SC1815  
QQSF02SA1175  
NQS10KTA1267  
NQS40KTA1266  
2SA1318TZ  
R36  
R37  
TRANSISTOR KTA1267(GR) or  
TRANSISTOR KTA1266(GR) or  
TRANSISTOR 2SA1318(T)-AANP or  
TRANSISTOR 2SA1318(U)-AANP or  
TRANSISTOR 2SA1015-GR(TPE2)  
RES. BUILT-IN TRANSISTOR BA1F4M-T or  
RES. BUILT-IN TRANSISTOR KRC103M  
TRANSISTOR 2SC2785(F) or  
R38  
R39  
R40  
R43  
R44  
2SA1318UZ  
QQS102SA1015  
QQSZ00BA1F4M  
NQSZ0KRC103M  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
Q794  
Q825  
R51  
R52  
R54  
R102  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
20030303  
13-7  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
R103  
R104  
R105  
R108  
R109  
R111  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 2.7k Ω  
CARBON RES. 1/4W J 4.7k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 470k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0222  
RCX4JATZ0272  
RCX4JATZ0472  
RCX4JATZ0103  
RCX4JATZ0103  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0103  
RCX4JATZ0474  
RCX4JATZ0102  
RCX6JATZ0102  
JW5.0T  
CARBON RES. 1/6W J 100 Ω  
PCB JUMPER D0.6-P5.0  
RCX6JATZ0101  
JW5.0T  
R198  
R301  
R302  
CARBON RES. 1/4W J 6.8k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0682  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0103  
RCX4JATZ0222  
RCX4JATZ0101  
RCX6JATZ0101  
JW5.0T  
R303  
R305  
R112  
R113  
R114  
R320  
R323  
R326  
R116  
R132  
R133  
R135  
R136  
R137  
PCB JUMPER D0.6-P5.0  
JW5.0T  
PCB JUMPER D0.6-P5.0  
JW5.0T  
R327  
R328  
R329  
R330  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 100k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 220k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0222  
RCX4JATZ0104  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0224  
RCX4JATZ0223  
RCX4JATZ0102  
RCX6JATZ0102  
JW5.0T  
CARBON RES. 1/4W J 3.3k Ω  
CARBON RES. 1/4W J 56k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 330 Ω or  
CARBON RES. 1/6W J 330 Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0332  
RCX4JATZ0563  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0331  
RCX6JATZ0331  
JW5.0T  
R138  
R139  
R140  
R333  
R342  
R344  
R345  
R346  
CARBON RES. 1/4W J 6.8k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0682  
RCX4JATZ0103  
RCX4JATZ0102  
RCX6JATZ0102  
JW5.0T  
R141  
R142  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0471  
RCX6JATZ0471  
JW5.0T  
R150  
R153  
R347  
R348  
R355  
R356  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 4.7k Ω  
CARBON RES. 1/4W J 6.8k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 4.7k Ω  
CARBON RES. 1/4W J 5.6k Ω  
CARBON RES. 1/4W J 3.9k Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0103  
RCX4JATZ0472  
RCX4JATZ0682  
RCX4JATZ0223  
RCX4JATZ0472  
RCX4JATZ0562  
RCX4JATZ0392  
JW5.0T  
CARBON RES. 1/4W J 27k Ω  
CARBON RES. 1/4W J 15k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
PCB JUMPER D0.6-P5.0  
RCX4JATZ0273  
RCX4JATZ0153  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
JW5.0T  
R154  
R156  
R157  
R158  
R159  
R161  
R163  
R357  
R358  
R362  
R417  
R422  
R427  
R445  
R503  
R504  
CARBON RES. 1/4W J 180k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 3.3k Ω  
CARBON RES. 1/4W J 68k Ω  
CARBON RES. 1/4W J 3.3 Ω or  
CARBON RES. 1/6W J 3.3 Ω  
CARBON RES. 1/4W J 1.8k Ω  
CARBON RES. 1/4W J 2.7 Ω or  
CARBON RES. 1/6W J 2.7 Ω  
CARBON RES. 1/4W J 2.7 Ω or  
CARBON RES. 1/6W J 2.7 Ω  
CARBON RES. 1/4W J 2.7 Ω or  
CARBON RES. 1/6W J 2.7 Ω  
RCX4JATZ0184  
RCX4JATZ0222  
RCX4JATZ0222  
RCX4JATZ0332  
RCX4JATZ0683  
RCX4JATZ03R3  
RCX6JATZ03R3  
RCX4JATZ0182  
RCX4JATZ02R7  
RCX6JATZ02R7  
RCX4JATZ02R7  
RCX6JATZ02R7  
RCX4JATZ02R7  
RCX6JATZ02R7  
RN024R7ZU001  
RN024R7DP004  
RCX4JATZ0272  
RCX4JATZ0681  
RCX6JATZ0681  
RCX4JATZ0223  
RCX4JATZ0223  
RCX4JATZ0182  
RCX4JATZ0223  
RCX4JATZ0223  
RCX4JATZ0223  
RCX4JATZ0471  
R164  
R165  
R166  
R167  
R168  
R170  
R171  
R172  
R173  
R174  
R176  
R505  
R506  
R507  
R508  
R513# METAL OXIDE FILM RES. 2W J 4.7 Ω or  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 100 Ω or  
RCX4JATZ0223  
RCX4JATZ0103  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0223  
RCX4JATZ0222  
RCX4JATZ0101  
#
METAL OXIDE FILM RES. 2W J 4.7 Ω  
CARBON RES. 1/4W J 2.7k Ω  
CARBON RES. 1/4W J 680 Ω or  
CARBON RES. 1/6W J 680 Ω  
R514  
R516  
R177  
R178  
R520# CARBON RES. 1/4W J 22k Ω  
R522  
R531  
R532  
R533  
R534  
R535  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 1.8k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 470 Ω or  
R193  
R195  
R196  
20030303  
13-8  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 680 Ω or  
CARBON RES. 1/6W J 680 Ω  
CARBON RES. 1/4W J 680 Ω or  
CARBON RES. 1/6W J 680 Ω  
CARBON RES. 1/4W J 680 Ω or  
CARBON RES. 1/6W J 680 Ω  
CARBON RES. 1/4W J 6.8k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 2.7k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 1.5k Ω  
RCX6JATZ0471  
RCX4JATZ0681  
RCX6JATZ0681  
RCX4JATZ0681  
RCX6JATZ0681  
RCX4JATZ0681  
RCX6JATZ0681  
RCX4JATZ0682  
RCX4JATZ0222  
RCX4JATZ0272  
RCX4JATZ0103  
RCX4JATZ0152  
RN01102ZU001  
RN01102DP003  
RN018R2ZU001  
RN018R2DP003  
RCX4JATZ0222  
RCX4JATZ0332  
RCX4JATZ0152  
RCX4JATZ0104  
RCX4JATZ0183  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0473  
RCX4JATZ0154  
RCX4JATZ0122  
RCX4JATZ0104  
RCX4JATZ0103  
RCX4JATZ0274  
RCX4JATZ0333  
RCX4JATZ0103  
RCX4JATZ0473  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0564  
RCX4JATZ0150  
RCX6JATZ0150  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0331  
RCX6JATZ0331  
RCX4JATZ0150  
RCX6JATZ0150  
RCX4JATZ0150  
RCX6JATZ0150  
JW5.0T  
R598# CARBON RES. 1/4W J 33k Ω  
R599# CARBON RES. 1/4W J 15k Ω  
R601# CEMENT RES. 7W K 0.56 Ω or  
RCX4JATZ0333  
RCX4JATZ0153  
RW07R56DP007  
RW07R56PG001  
RCX4JATZ0824  
RCX4JATZ0824  
RCX4JATZ0824  
RCX4JATZ0824  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0824  
RW05R27DP005  
RW05R27PG001  
RCX4JATZ0103  
RCX4JATZ0391  
RCX6JATZ0391  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0152  
RCX4JATZ0470  
RCX6JATZ0470  
RCX4JATZ0390  
RCX6JATZ0390  
RN02153ZU001  
RN02153DP004  
RCX4JATZ0153  
RCX4JATZ0223  
RCX4JATZ0272  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0153  
RCX4JATZ0153  
RCX4JATZ0474  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0104  
RCX4JATZ0823  
JW5.0T  
R541  
R542  
R543  
#
CEMENT RESISTOR 7W K 0.56 Ω H=10MM  
R602  
R603  
R604  
R605  
R607  
CARBON RES. 1/4W J 820k Ω  
CARBON RES. 1/4W J 820k Ω  
CARBON RES. 1/4W J 820k Ω  
CARBON RES. 1/4W J 820k Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 820k Ω  
R545  
R546  
R547  
R548  
R549  
R608  
R609  
R551# METAL OXIDE FILM RES. 1W J 1k Ω or  
METAL OXIDE FILM RES. 1W J 1k Ω  
R552# METAL OXIDE FILM RES. 1W J 8.2 Ω or  
#
R613# CEMENT RES. 5W K 0.27 Ω or  
#
CEMENT RESISTOR 5W K 0.27 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 390 Ω or  
CARBON RES. 1/6W J 390 Ω  
#
METAL OXIDE FILM RES. 1W J 8.2 Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 3.3k Ω  
R616  
R618  
R553  
R554  
R555# CARBON RES. 1/4W J 1.5k Ω  
R620# CARBON RES. 1/4W J 100 Ω or  
R556  
R557  
R558  
CARBON RES. 1/4W J 100k Ω  
CARBON RES. 1/4W J 18k Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 150k Ω  
CARBON RES. 1/4W J 1.2k Ω  
CARBON RES. 1/4W J 100k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 270k Ω  
CARBON RES. 1/4W J 33k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 560k Ω  
#
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 1.5k Ω  
CARBON RES. 1/4W J 47 Ω or  
CARBON RES. 1/6W J 47 Ω  
CARBON RES. 1/4W J 39 Ω or  
CARBON RES. 1/6W J 39 Ω  
R621  
R622  
R559  
R560  
R561  
R562  
R563  
R564  
R565  
R566  
R567  
R568  
R623  
R651# METAL OXIDE FILM RES. 2W J 15k Ω or  
#
METAL OXIDE FILM RES. 2W J 15k Ω  
CARBON RES. 1/4W J 15k Ω  
CARBON RES. 1/4W J 22k Ω  
R652  
R653  
R654# CARBON RES. 1/4W J 2.7k Ω  
R655  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
R656# CARBON RES. 1/4W J 15k Ω  
R657  
R658  
R660  
CARBON RES. 1/4W J 15k Ω  
CARBON RES. 1/4W J 470k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
R569  
R575# CARBON RES. 1/4W J 15 Ω or  
#
CARBON RES. 1/6W J 15 Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 330 Ω or  
CARBON RES. 1/6W J 330 Ω  
CARBON RES. 1/4W J 15 Ω or  
CARBON RES. 1/6W J 15 Ω  
CARBON RES. 1/4W J 15 Ω or  
CARBON RES. 1/6W J 15 Ω  
PCB JUMPER D0.6-P5.0  
R576  
R661# CARBON RES. 1/4W J 100k Ω  
R662# CARBON RES. 1/4W J 82k Ω  
R663# PCB JUMPER D0.6-P5.0  
R577  
R578  
R579  
R581  
R664# CARBON RES. 1/4W J 12k Ω  
R665# CARBON RES. 1/4W J 5.6k Ω  
R666# METAL OXIDE FILM RES. 1W J 100k Ω or  
RCX4JATZ0123  
RCX4JATZ0562  
RN01104ZU001  
RN01104DP003  
RCX4JATZ0333  
RCX4JATZ0333  
RCX4JATZ0333  
RCX4JATZ0104  
RCX4JATZ0332  
RCX4JATZ0332  
RCX4JATZ0104  
RCX4JATZ0223  
RCX4JATZ0103  
RCX4JATZ0153  
RCX4JATZ0473  
RCX4JATZ0332  
RCX4JATZ0103  
RCX4JATZ0120  
RCX6JATZ0120  
RN02330ZU001  
RN02330DP004  
#
METAL OXIDE FILM RES. 1W J 100k Ω  
R667# CARBON RES. 1/4W J 33k Ω  
R668# CARBON RES. 1/4W J 33k Ω  
R669# CARBON RES. 1/4W J 33k Ω  
R670# CARBON RES. 1/4W J 100k Ω  
R671# CARBON RES. 1/4W J 3.3k Ω  
R672# CARBON RES. 1/4W J 3.3k Ω  
R673# CARBON RES. 1/4W J 100k Ω  
R583# METAL OXIDE FILM RES. 2W J 1.5 Ω or  
METAL OXIDE FILM RES. 2W J 1.5 Ω  
RN021R5ZU001  
RN021R5DP004  
JW5.0T  
#
R584# PCB JUMPER D0.6-P5.0  
R585# CARBON RES. 1/4W J 10k Ω  
R586# CARBON RES. 1/4W J 470k Ω  
RCX4JATZ0103  
RCX4JATZ0474  
RCX4JATZ0474  
RCX4JATZ0473  
RCX4JATZ0473  
RCX4JATZ0223  
RCX4JATZ0184  
RCX4JATZ0224  
RCX4JATZ0683  
RCX4JATZ0104  
RCX4JATZ0104  
RCX4JATZ0822  
R587  
R588  
CARBON RES. 1/4W J 470k Ω  
R674  
R676  
R677  
R678  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 15k Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 47k Ω  
R589# CARBON RES. 1/4W J 47k Ω  
R590 CARBON RES. 1/4W J 22k Ω  
R591# CARBON RES. 1/4W J 180k Ω  
R592# CARBON RES. 1/4W J 220k Ω  
R593# CARBON RES. 1/4W J 68k Ω  
R594# CARBON RES. 1/4W J 100k Ω  
R679# CARBON RES. 1/4W J 3.3k Ω  
R680 CARBON RES. 1/4W J 10k Ω  
R681# CARBON RES. 1/4W J 12 Ω or  
CARBON RES. 1/6W J 12 Ω  
R682# METAL OXIDE FILM RES. 2W J 33 Ω or  
METAL OXIDE FILM RES. 2W J 33 Ω  
#
R596  
R597  
CARBON RES. 1/4W J 100k Ω  
CARBON RES. 1/4W J 8.2k Ω  
#
20030303  
13-9  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
R683# METAL RESISTOR 2W J 39 Ω or  
RN02390ZU001  
RN02390DP004  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0100  
RCX6JATZ0100  
RCX4JATZ0472  
RCX4JATZ0100  
RCX6JATZ0100  
JW5.0T  
R803  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 18k Ω  
CARBON RES. 1/4W J 18k Ω  
CARBON RES. 1/4W J 5.6k Ω  
CARBON RES. 1/4W J 33k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
CARBON RES. 1/4W J 4.7k Ω  
METAL OXIDE FILM RES. 2W J 0.47 Ω or  
METAL OXIDE FILM RES. 2W J 0.47 Ω  
CARBON RES. 1/4W J 560 Ω or  
CARBON RES. 1/6W J 560 Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 22k Ω  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0183  
RCX4JATZ0183  
RCX4JATZ0562  
RCX4JATZ0333  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0103  
RCX4JATZ0103  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0223  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0472  
RN02R47ZU001  
RN02R47DP004  
RCX4JATZ0561  
RCX6JATZ0561  
RCX4JATZ0222  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0223  
RCX4JATZ0331  
RCX6JATZ0331  
RCX4JATZ0222  
RCX4JATZ0222  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0103  
RCX4JATZ0470  
RCX6JATZ0470  
RCX4JATZ0750  
RCX6JATZ0750  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0103  
RCX4JATZ0750  
RCX6JATZ0750  
JW5.0T  
#
METAL OXIDE FILM RES. 2W J 39 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 10 Ω or  
CARBON RES. 1/6W J 10 Ω  
R686  
R804  
R687  
R811  
R812  
R817  
R818  
R827  
R694# CARBON RES. 1/4W J 4.7k Ω  
R696# CARBON RES. 1/4W J 10 Ω or  
#
CARBON RES. 1/6W J 10 Ω  
PCB JUMPER D0.6-P5.0  
R697  
R701  
CARBON RES. 1/4W J 82 Ω or  
CARBON RES. 1/6W J 82 Ω  
CARBON RES. 1/4W J 82 Ω or  
CARBON RES. 1/6W J 82 Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 33k Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 33k Ω  
CARBON RES. 1/4W J 82 Ω or  
CARBON RES. 1/6W J 82 Ω  
CARBON RES. 1/4W J 330 Ω or  
CARBON RES. 1/6W J 330 Ω  
CARBON RES. 1/4W J 82 Ω or  
CARBON RES. 1/6W J 82 Ω  
CARBON RES. 1/4W J 330 Ω or  
CARBON RES. 1/6W J 330 Ω  
CARBON RES. 1/4W J 82 Ω or  
CARBON RES. 1/6W J 82 Ω  
CARBON RES. 1/4W J 82 Ω or  
CARBON RES. 1/6W J 82 Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 33k Ω  
CARBON RES. 1/4W J 47k Ω  
CARBON RES. 1/4W J 2.2k Ω  
CARBON RES. 1/4W J 33k Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 27k Ω  
CARBON RES. 1/4W J 56k Ω  
CARBON RES. 1/4W J 18k Ω  
CARBON RES. 1/4W J 1.8k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 560 Ω or  
CARBON RES. 1/6W J 560 Ω  
CARBON RES. 1/4W J 22k Ω  
CARBON RES. 1/4W J 27k Ω  
CARBON RES. 1/4W J 56k Ω  
CARBON RES. 1/4W J 18k Ω  
CARBON RES. 1/4W J 1.8k Ω  
CARBON RES. 1/4W J 1k Ω or  
CARBON RES. 1/6W J 1k Ω  
CARBON RES. 1/4W J 560 Ω or  
CARBON RES. 1/6W J 560 Ω  
CARBON RES. 1/4W J 4.7k Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 4.7k Ω  
CARBON RES. 1/4W J 4.7k Ω  
CARBON RES. 1/4W J 10k Ω  
RCX4JATZ0820  
RCX6JATZ0820  
RCX4JATZ0820  
RCX6JATZ0820  
RCX4JATZ0473  
RCX4JATZ0222  
RCX4JATZ0333  
RCX4JATZ0473  
RCX4JATZ0222  
RCX4JATZ0333  
RCX4JATZ0820  
RCX6JATZ0820  
RCX4JATZ0331  
RCX6JATZ0331  
RCX4JATZ0820  
RCX6JATZ0820  
RCX4JATZ0331  
RCX6JATZ0331  
RCX4JATZ0820  
RCX6JATZ0820  
RCX4JATZ0820  
RCX6JATZ0820  
RCX4JATZ0473  
RCX4JATZ0222  
RCX4JATZ0333  
RCX4JATZ0473  
RCX4JATZ0222  
RCX4JATZ0333  
RCX4JATZ0223  
RCX4JATZ0273  
RCX4JATZ0563  
RCX4JATZ0183  
RCX4JATZ0182  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0561  
RCX6JATZ0561  
RCX4JATZ0223  
RCX4JATZ0273  
RCX4JATZ0563  
RCX4JATZ0183  
RCX4JATZ0182  
RCX4JATZ0102  
RCX6JATZ0102  
RCX4JATZ0561  
RCX6JATZ0561  
RCX4JATZ0472  
RCX4JATZ0103  
RCX4JATZ0472  
RCX4JATZ0472  
RCX4JATZ0103  
R828  
R829  
R831  
R702  
R704  
R705  
R706  
R707  
R708  
R709  
R711  
R832  
R833  
R834  
R841  
R842  
R713  
R716  
R718  
R721  
R722  
R843  
R844  
R845  
R851# CARBON RES. 1/4W J 330 Ω or  
CARBON RES. 1/6W J 330 Ω  
#
R855# CARBON RES. 1/4W J 2.2k Ω  
R856# CARBON RES. 1/4W J 2.2k Ω  
R951  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 47 Ω or  
CARBON RES. 1/6W J 47 Ω  
CARBON RES. 1/4W J 75 Ω or  
CARBON RES. 1/6W J 75 Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 10k Ω  
CARBON RES. 1/4W J 75 Ω or  
CARBON RES. 1/6W J 75 Ω  
PCB JUMPER D0.6-P5.0  
R724  
R725  
R726  
R727  
R728  
R729  
R751  
R752  
R753  
R754  
R755  
R756  
R952  
R953  
R954  
R956  
R957  
R959  
R961  
R962  
CARBON RES. 1/4W J 470 Ω or  
CARBON RES. 1/6W J 470 Ω  
RCX4JATZ0471  
RCX6JATZ0471  
RCX4JATZ0222  
RCX4JATZ0103  
R757  
R966# CARBON RES. 1/4W J 2.2k Ω  
R967# CARBON RES. 1/4W J 10k Ω  
R761  
R762  
R763  
R764  
R765  
R766  
SWITCHES  
TACT SWITCH SKQSAB or  
SW101  
SW102  
SW103  
SW104  
SST0101AL038  
SST0101HH003  
SST0101AL029  
SST0101AL038  
SST0101HH003  
SST0101AL029  
SST0101AL038  
SST0101HH003  
SST0101AL029  
SST0101AL038  
SST0101HH003  
SST0101AL029  
TACT SWITCH KSM0612B or  
TACT SWITCH SKHHAM  
TACT SWITCH SKQSAB or  
TACT SWITCH KSM0612B or  
TACT SWITCH SKHHAM  
TACT SWITCH SKQSAB or  
TACT SWITCH KSM0612B or  
TACT SWITCH SKHHAM  
TACT SWITCH SKQSAB or  
TACT SWITCH KSM0612B or  
TACT SWITCH SKHHAM  
R767  
R771  
R772  
R791  
R792  
R793  
20030303  
13-10  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
TACT SWITCH SKQSAB or  
Part No.  
Ref. No.  
Description  
PCB JUMPER D0.6-P5.0  
Part No.  
JW5.0T  
SW105  
SST0101AL038  
SST0101HH003  
SST0101AL029  
SST0101AL038  
SST0101HH003  
SST0101AL029  
JS801  
JS802  
JS821  
JS822  
L-1  
TACT SWITCH KSM0612B or  
TACT SWITCH SKHHAM  
TACT SWITCH SKQSAB or  
TACT SWITCH KSM0612B or  
TACT SWITCH SKHHAM  
PCB JUMPER D0.6-P10.0  
JW10.0T  
PCB JUMPER D0.6-P5.0  
JW5.0T  
SW106  
PCB JUMPER D0.6-P7.5  
JW7.5T  
SCREW, B-TIGHT M3X8 BIND HEAD+  
CLOTH(65) L7735TR:65X10X0.5T  
GBMB3080  
PB6  
0EM402149  
PS691# THERMISTOR ZPB58BL7R0F  
QNQZ58BL7R0F  
USESJRSUNT02  
USESJRSKK034  
USESJRSKK032  
MRNDC12QN014  
MRNDC12KB002  
MRNDC12DEC02  
MRNDC12MS013  
QVQZ0AVRS07D  
NVQZVR07N471  
NVQZR10D471K  
NVQZR07D471K  
NVQZ07D471KB  
FBB456PMR008  
LTF00CPP1019  
LTF00CPXB038  
LTH00CPY2004  
LTH00CPSA002  
LTT00CPKT095  
JW5.0T  
MISCELLANEOUS  
AC601# AC CORD LA-2413  
RCV101 REMOCON RECEIVE UNIT MIM-93M8DKL or  
REMOCON RECEIVE UNIT PIC-37042SR or  
REMOCON RECEIVE UNIT PIC-26042SR-2  
RL601# POWER RELAY SDT-S-112LMR  
WAC0172LW007  
0EM407156  
B-6  
HEAT SINK(PGM)ASSEMBLY L6250UA  
B-7  
HEAT SINK(PFN)ASSEMBLY L1520UZ  
HEAT SINK(PGN)ASSEMBLY L6250UA  
HEAT SINK(PGO) L6250UA  
0EM406353  
B-8  
0EM407158  
#
#
#
POWER RELAY RPEF-12-901 or  
RELAY GD12D1-O(M)-II or  
RELAY ALKS321  
B-9  
0EM407159  
BC571  
BC572  
BC602  
BC603  
BC652  
BC653  
BC654  
BC655  
BC656  
BC657  
BC691  
BC692  
CF31  
BEAD INDUCTORS FBA04HA600VB-00  
BEAD INDUCTORS FBA04HA600VB-00  
PCB JUMPER D0.6-P5.0  
LLBF00STU026  
LLBF00STU026  
JW5.0T  
SA601# SURGE ABSORBER AVR-S07D471KAAS or  
#
SURGE ABSORBER JVR-07N471K or  
SURGE ABSORBER CNR-10D471K or  
SURGE ABSORBER CNR-07D471K or  
SURGE ABSORBER PVR-07D471KB  
SAW FILTER SAFGM45M7VHHzC0B03  
FLYBACK TRANS BSC28-0731 or  
FLYBACK TRANSFORMER JF0501-2189  
HORIZONTAL DRAIVE TRANS Y2004 or  
HORIZONTAL DRAIVE TRANS CSA-LF044  
SWITCHING TRANS KD-L12-32V  
PCB JUMPER D0.6-P5.0  
BEAD INDUCTORS FBR07HA121TB-00  
BEAD INDUCTORS FBR07HA121TB-00  
PCB JUMPER D0.6-P5.0  
LLBF00ZTU021  
LLBF00ZTU021  
JW5.0T  
#
#
#
BEAD INDUCTORS FBR07HA121TB-00  
BEAD INDUCTORS FBR07HA121TB-00  
BEAD INDUCTORS FBR07HA121TB-00  
BEAD INDUCTORS FBR07HA121TB-00  
BEAD INDUCTORS FBR07HA121TB-00  
BEAD INDUCTORS FBR07HA121TB-00  
CERAMIC TRAP 4.5MHz or  
LLBF00ZTU021  
LLBF00ZTU021  
LLBF00ZTU021  
LLBF00ZTU021  
LLBF00ZTU021  
LLBF00ZTU021  
FBE455PMR003  
FBE455PMS001  
FBB455PMR004  
FBB455PMS001  
WX3001A2FF14  
WX1L1520-103  
WX1L1520-101  
PAGJ20CAG402  
PAGD20CW3402  
PAGE20CW3402  
PAGG20CNG402  
XH01Z00LY001  
XH01Z00DK001  
1790424  
SF1  
T571#  
#
T572  
T601#  
TH556  
TP300  
TP301  
TP302  
TP500  
TP501  
TP591  
TP592  
TP601  
TU1  
CERAMIC TRAP 4.5MHz  
PCB JUMPER D0.6-P10.0  
JW10.0T  
CF32  
CLN1  
CERAMIC FILTER SFSRA4M50CF00-B0 or  
CERAMIC FILTER 4.5MHz  
PCB JUMPER D0.6-P7.5  
JW7.5T  
PCB JUMPER D0.6-P7.5  
JW7.5T  
LEAD WIRE UL1007 AWG22 BLACK 140MM  
PCB JUMPER D0.6-P7.5  
JW7.5T  
CLN301 WIRE ASSEMBLY WX1L1520-103  
CLN501 WIRE ASSEMBLY WX1L1520-101  
PCB JUMPER D0.6-P7.5  
JW7.5T  
PCB JUMPER D0.6-P5.0  
JW5.0T  
F601#  
#
FUSE 4A/125V 237 TYPE or  
FUSE TDS4A125VU/C or  
FUSE STC4A125V U/CT or  
FUSE 4.00A/125V  
PCB JUMPER D0.6-P5.0  
JW5.0T  
PCB JUMPER D0.6-P7.5  
JW7.5T  
#
TUNER UNIT TEQH9-001A  
UTUNNTUAL032  
VRCB203KA011  
VRCB203HH014  
VRCB502KA011  
VRCB502HH014  
VRCB503KA011  
VRCB503HH014  
FXD355LLN003  
#
VR561  
CARBON P.O.T. 20k Ω B or  
FH601  
FUSE HOLDER MSF-015 or  
FUSE HOLDER FH-V-03078 or  
HOLDER, FUSE CNT41-0014  
FUSE HOLDER MSF-015 or  
FUSE HOLDER FH-V-03078 or  
HOLDER, FUSE CNT41-0014  
CARBON P.O.T. 20k Ω B  
VR562  
CARBON P.O.T. 5k Ω B or  
CARBON P.O.T. 5k Ω B  
FH602  
XH01Z00LY001  
XH01Z00DK001  
1790424  
VR661# CARBON P.O.T. 50k Ω B or  
#
CARBON P.O.T. 50k Ω B  
X301  
X'TAL 3.579545 MHz  
GP641# GAP. FNR-G3.10D  
FAZ000LD6005  
JXRL010LY003  
JXRL020LY045  
JYRL020LY011  
JYEL040LY002  
JXRL010LY050  
JXRL010RP010  
JXRL010LY052  
JXRL010RP011  
JYRL010LY014  
JYRL010RP008  
JW5.0T  
JK701  
JK702  
JK703  
JK711  
JK721  
RCA JACK(YELLOW) MSP-281V4-B  
RCA JACK 2P MSP-282V13 PBSN  
RCA JACK 2P(SW) MSP-292V07 PBSN  
Y/C JACK 1P(SW) MDC-070V1-A  
RCA JACK(YELLOW) MTJ-032-06B-20 or  
RCA JACK 1P AV-8.4-9Y  
CRT CBA  
Ref. No.  
Description  
Part No.  
CRT CBA  
Consists of the following  
------------  
CAPACITORS  
JK722  
JK723  
RCA JACK(WHITE) MTJ-032-06B-22 or  
RCA JACK 1P AV-8.4-9W  
C1501  
C1502  
C1510  
ELECTROLYTIC CAP. 100µF/10V M or  
ELECTROLYTIC CAP. 100µF/10V M  
ELECTROLYTIC CAP. 10µF/50V M or  
ELECTROLYTIC CAP. 10µF/50V M  
CERAMIC CAP. B K 2200pF/2KV or  
CERAMIC CAP. B K 2200pF/2KV or  
CERAMIC CAP. B K 2200pF/2KV  
CERAMIC CAP.(AX) B K 470pF/50V  
CERAMIC CAP.(AX) B K 0.01µF/50V  
CERAMIC CAP.(AX) B K 220pF/50V  
CERAMIC CAP.(AX) B K 0.01µF/50V  
CE1AMASTL101  
CE1AMASDL101  
CE1JMASTL100  
CE1JMASDL100  
CCD3DKD0B222  
CCD3DKP0B222  
CA3D222MR030  
CCA1JKT0B471  
CA1J103TU011  
CCA1JKT0B221  
CA1J103TU011  
RCA JACK(RED) MTJ-032-06A-21 or  
RCA JACK 1P(RED)WITH SW ITCH AV1-09S-2  
PCB JUMPER D0.6-P5.0  
JS102  
JS104  
JS105  
JS171  
JS191  
JS301  
JS570  
JS642  
PCB JUMPER D0.6-P5.0  
JW5.0T  
PCB JUMPER D0.6-P5.0  
JW5.0T  
PCB JUMPER D0.6-P15.0  
JW15.0T  
PCB JUMPER D0.6-P5.0  
JW5.0T  
C1511  
C1512  
C1521  
C1522  
PCB JUMPER D0.6-P5.0  
JW5.0T  
PCB JUMPER D0.6-P5.0  
JW5.0T  
PCB JUMPER D0.6-P10.0  
JW10.0T  
20030303  
13-11  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ref. No.  
Description  
Part No.  
Ref. No.  
Description  
Part No.  
C1531  
C1532  
CERAMIC CAP.(AX) B K 470pF/50V  
CERAMIC CAP.(AX) B K 0.01µF/50V  
CONNECTORS  
CCA1JKT0B471  
CA1J103TU011  
R1512  
R1514  
CARBON RES. 1/4W J 1.5k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 820 Ω or  
CARBON RES. 1/6W J 820 Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
RCX4JATZ0152  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0821  
RCX6JATZ0821  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0101  
RCX6JATZ0101  
RN03103ZU001  
RN03103DP005  
RCX4JATZ0152  
RCX4JATZ0152  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0821  
RCX6JATZ0821  
RCX4JATZ0221  
RCX6JATZ0221  
RCX4JATZ0101  
RCX6JATZ0101  
RN03103ZU001  
RN03103DP005  
RCX4JATZ0152  
RCX4JATZ0152  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0821  
RCX6JATZ0821  
RCX4JATZ0221  
RCX6JATZ0221  
R1515  
R1518  
R1519  
CN1501 PIN CONNECTOR 005P-5100  
DIODES  
SWITCHING DIODE 1SS133(T-77) or  
JTEA001TG001  
D1501  
QDTZ001SS133  
NDTZ001N4148  
1SS176T  
SWITCHING DIODE 1N4148 or  
DIODE 1SS176TPA7  
COILS  
L1501# INDUCTOR 150µH-J-5FT or  
R1520# METAL RESISTOR 3W J 10k Ω or  
LLARJCSTU151  
LLARKDQKA151  
JW5.0T  
#
FIXED METAL OXIDE FILM RES. 3W J 10k Ω  
#
INDUCTOR 150µH-K  
R1521  
R1522  
R1524  
CARBON RES. 1/4W J 1.5k Ω  
CARBON RES. 1/4W J 1.5k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 820 Ω or  
CARBON RES. 1/6W J 820 Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
L1511  
L1521  
L1531  
PCB JUMPER D0.6-P5.0  
PCB JUMPER D0.6-P5.0  
PCB JUMPER D0.6-P5.0  
JW5.0T  
JW5.0T  
TRANSISTORS  
R1525  
R1528  
R1529  
Q1511  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC5360 or  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
R1530# METAL RESISTOR 3W J 10k Ω or  
2SC3331UZ  
#
FIXED METAL OXIDE FILM RES. 3W J 10k Ω  
QQS102SC1815  
QQ9Z02SC5360  
QQ9Z02SC4544  
NQ5Z0KTC3229  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
R1531  
R1532  
R1534  
CARBON RES. 1/4W J 1.5k Ω  
CARBON RES. 1/4W J 1.5k Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 820 Ω or  
CARBON RES. 1/6W J 820 Ω  
CARBON RES. 1/4W J 220 Ω or  
CARBON RES. 1/6W J 220 Ω  
Q1512  
Q1521  
TRANSISTOR 2SC4544 or  
TRANSISTOR KTC3229  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC5360 or  
R1535  
R1538  
MISCELLANEOUS  
BEAD INDUCTORS FBR07HA121TB-00  
BC1501  
LLBF00ZTU021  
JSCC290PK006  
JSCC290HD012  
JW5.0T  
2SC3331UZ  
JK1501# CRT SOCKET ISHS40ST or  
QQS102SC1815  
QQ9Z02SC5360  
QQ9Z02SC4544  
NQ5Z0KTC3229  
QQSF02SC2785  
QQSH02SC2785  
QQSJ02SC2785  
NQS10KTC3199  
NQS40KTC3198  
2SC3331TZ  
#
CRT SOCKET HPS0521-012212  
PCB JUMPER D0.6-P5.0  
Q1522  
Q1531  
JS1551  
TRANSISTOR 2SC4544 or  
TRANSISTOR KTC3229  
TRANSISTOR 2SC2785(F) or  
TRANSISTOR 2SC2785(H) or  
TRANSISTOR 2SC2785(J) or  
TRANSISTOR KTC3199(GR) or  
TRANSISTOR KTC3198(GR) or  
TRANSISTOR 2SC3331(T)-AANP or  
TRANSISTOR 2SC3331(U)-AANP or  
TRANSISTOR 2SC1815-GR(TPE2)  
TRANSISTOR 2SC5360 or  
2SC3331UZ  
QQS102SC1815  
QQ9Z02SC5360  
QQ9Z02SC4544  
NQ5Z0KTC3229  
Q1532  
TRANSISTOR 2SC4544 or  
TRANSISTOR KTC3229  
RESISTORS  
R1501  
R1502  
R1503  
R1509  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
CARBON RES. 1/4W J 100 Ω or  
CARBON RES. 1/6W J 100 Ω  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RCX4JATZ0101  
RCX6JATZ0101  
RN03103ZU001  
RN03103DP005  
RCX4JATZ0152  
R1510# METAL RESISTOR 3W J 10k Ω or  
#
FIXED METAL OXIDE FILM RES. 3W J 10k Ω  
CARBON RES. 1/4W J 1.5k Ω  
R1511  
20030303  
13-12  
L6650EL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed in Japan  
2003-03-20 HO  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shindaiwa Trimmer 82053 User Manual
Sony CD Player CDU625 User Manual
Sony Clock Radio J30SDI User Manual
Sony DVD Recorder RDR GX380 User Manual
Sony Printer Accessories TA E1 User Manual
Sony Projection Television KDS 50A2000 User Manual
Spin Master Games Flip Trix User Manual
Summit Printer Accessories HL 630 OPC User Manual
SunBriteTV Car Stereo System DS 3214TSL User Manual
Sylvania Portable DVD Player SDVD7012 User Manual