HOMEOWNER'S CARE AND
OPERATION INSTRUCTIONS
WOOD BURNING FIREPLACES
MODEL HCD36MH
36" Wood Burning Fireplaces
P/N 725,038M REV. A 03/2006
MODELS
HCD36MH
The information contained in this manual applies to all model fireplaces
identified on this page. This information will help you obtain safe and
dependable service from your fireplace system. Keep this document in
a safe place for future reference.
Before you start your first fire, read this Care and Operations Manual
carefully to be sure you understand your fireplace system completely.
Failure to follow these suggestions could result in hazardous operation
or fireplace malfunction, creating a serious potential for personal injury
and/or property damage.
If you have any questions regarding the safe use or operation of your
fireplace, contact your local distributor or your contractor/builder.
Most chimney systems will require onsite completion after placement of
the manufactured home.
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WH Report No.
J20051034-231
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Closed screens prevent fire, sparks and
embers from popping out of the firebox
while a fire is burning. Pull screens back
when adding wood to the firebox.
6. Why use a fuel grate? Besides positioning
thefirebedproperly,itprotectstherefractory
floor,backandsidesofthefireplace.Further,
it ensures a proper flow of combustion air
into and around the firebed. The grate must
be used at all times when burning. Your
warranty may be voided without the use
of this grate.
7. Remember, your fireplace is not intended to
heatyourentirehome. Theiruniquedesigns
areintendedforarchitectural,decoratingand
aestheticconsiderations.Usingthisfireplace
toheatlargeareasmayleadtooverfiringand
void your warranty.
Prior to installing any gas log set, refer to the
fireplace installation instructions for verification
of mantel heights and placement of combustible
materials around the firebox opening.
3. Differentwoodsvarywidelyinflameheights,
flame intensities, smoke characteristics
and in sparking. Most hardwoods do not
spark.
4. Most freshly cut “green” wood will not burn
wellandwillsmoke.Greenwoodcanbefrom
10 to 40 percent less efficient than air-dried
seasoned wood.
5. Moistureandresinfoundinsideunseasoned
wood cells will build up pressure under heat
and explode as sparks.
6. Most wood needs to be seasoned 9 to 12
months to reduce the moisture content and
produce good steady fires. When moisture
content is reduced from 60 to 20%, the gain
in heat potential is nearly 7%.
Wood Fuel Pointers
Wood is a wonderful renewable fuel source.
Normally it burns clean, leaving only a minimum
of waste ash, provides comforting heat and can
provide a variety of aromas and visual images.
You will want to know which woods are best for
use.Sometimesyoumaywantaquick,shortfire
to offset a morning chill. Soft woods are prefer-
able in this case. Other times you would want
more slow burning and a uniform heat output.
Hardwoods are preferable for this use.
7. Proper storage of wood, especially during
seasoning,isessential.Werecommendthat
you:
The amount of heat available from the logs will
be about equal on a weight basis. However,
logs are generally not weighed so the amount
of heat will depend on:
FUELS
a. Never store wood on the ground. This
will cause rotting and insect infiltra-
tion. Raise wood on flat rock or scrap
wood.
b. Stackwoodlooselytoallowaircircula-
tion.
c. Store wood where it will not be exces-
sively exposed to weather, such as
under a tarp or under a roof.
d. Do not stack wood directly against the
walls of your home.
Never Use Coal in Your Fireplace
Your fireplace system is not designed to be
used with coal derivative products. The com-
bustion process of certain types of coal can
deposit corrosive materials in the fireplace and
chimney system which can lead to premature
product failure. Never use coal as a fuel in this
fireplace system.
1. The type of wood used.
2. How dry it is.
3. How many logs you put in.
4. The size of the logs.
Thelaststatementmeansthatonebiglogweigh-
ing 10 pounds has as much heating potential
as 10 pounds of twigs. However, air cannot get
at the solid log to feed the fire so the solid log
will burn slowly. While you would get the same
amount of heat out of either fire, the smaller the
pieces of wood and the more air space around
them, the faster the fire will burn.
DECORATIVE GAS LOG SETS
8. Be a knowledgeable wood buyer. There is a
differenceincordsizes.Astandardcordstack
of logs is 4 ft. high by 8 ft. long by 4 ft.
deep or the equivalent of this cubic footage,
(Figure 1).
Ifyourfireplacesystemwasinstalledwithagas
line, you may wish to install one of two types of
gas log sets. This fireplace has been tested and
approvedforusewithadecorativegasappliance
incorporating an automatic shut-off device and
complying withtheStandardforDecorativeGas
Appliances for installation in vented fireplaces,
ANSI Z21.60 (latest edition).
DISPOSAL OF ASHES
Ashesshouldbeplacedinametalcontainerwith
a tight fitting lid. The closed container of ashes
should be placed on a noncombustible floor or
on the ground, well away from all combustible
materials, pending final disposal.
Standard
Cord of
Wood
8'
Decorative gas appliances may be installed in
these fireplaces. Installation must be in ac-
cordancewiththenationalFuelGasCode, ANSI
Z223.1-latest edition for compliance with the
revised U.L. 127 Standard.
Iftheashesaretobedisposedofbyburialinsoil
or other wise locally dispersed, they should be
retained in the closed container until all cinders
have thoroughly cooled.
4'
CAUTION
SOFTWOOD VS HARDWOOD
4'
When using a decorative gas
appliance,thefireplacedamper
must be set in the fully open
position.
Softwoods contain about 15 percent highly
flammableresinwhichgeneratescreosotesoot
in the chimney flue. Burning softwood exclu-
sively may not be as desirable nor as safe as
burning denser hardwoods. Many experienced
fire-builders use small amounts of softwood
kindling and newspaper in conjunction with
starting a fire with split hardwood logs. Here
are some guidelines to remember:
Figure 1
A face cord is the same height and length as a
standard cord but the depth is only the length
of the logs (12, 18 or 24 inches). A face cord
can contain as little as 25% of the wood found
in a standard cord.
WARNING
Thisfireplacehasnotbeentested
with an unvented gas log set. To
reduce risk of fire or injury, do
not install an unvented gas log
set into this fireplace.
1. Softwoodsproducefastwarmingandshorter
fires. Hardwoods burn less vigorously, have
shorter flames and produce steady, glowing
coals.
2. Asageneralrule,denserwoodscontainmore
potential heat per pound. Most softwoods
offer moderate heat value per pound.
If you buy by the ton, remember that wood
becomes lighter as it dries. When buying green
or wet wood, ask for some extra poundage to
allow for the extra water you will be getting.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
9. When comparing woods of the same mois-
turecontentandsamespecies,wefindmost
woodshaveapproximatelythesameheating
potential per pound.
STARTING A FIRE
GLASS DOOR OPERATING SAFETY
PRECAUTIONS AND INSTRUCTIONS
1. To start a fire in a the fireplace properly, first
check the operation of the flue damper.
2. To prevent smoking at start-up, close any
window located near the fireplace when first
lighting a fire. The closed windows may be
reopened once a chimney draft is drawn in
the fireplace.
3. The grate in the firebox should be centered
on or over the bottom hearth so your fire
can breath properly. Crumble and twist
plenty of newspapers UNDER the grate and
criss-cross some small dry kindling sticks
on top of the paper or on the bottom of the
grate.
These fireplaces are equipped with glass
doors. Only use the doors provided with this
fireplace.
However, most wood is sold by volume, not
by weight. To determine the best heating
source, look at the density of various wood
types. (Density is the weight for a given size.
The higher the density, the more potential
heatoutput.Astandardcordhasavolumeof
128 cubic feet. This figure also includes the
airspacebetweenandaroundthewood.The
actual volume in a standard cord is between
60 and 100 cubic feet; depending on how
tightly the wood is packed.
WARNING
Your fireplace is equipped with
glass doors, it should be oper-
ated with the doors fully open or
fully closed. If the doors are left
partially open, gas and flames
may be drawn out of the open-
ing, creating risks of both fire
and smoke. Refer to Figure 3for
proper operating conditions.
Assuming that you are comparing two
standard cords of different species but the
same volume and moisture content, the
denser species will provide more BTU’s.
The table of wood species/densities reveals
more helpful guidelines.
4. Build a pyramid of three split logs (split will
startmuchfaster).Arrangetheunevenwood
to provide plenty of air space between.
5. Now, light the paper at both sides of the
firebox.
6. Close the screens to prevent the escape of
sparks and embers.
7. Close the damper only when your fire is
completely out and ashes are cold. Keep
closedwhenfireplaceisnotinusetoprevent
unnecessary loss of heated or cooled air.
HARDWOODS
DENSITY
Alser, Red
Ash
Aspen
Basswood, American
Beech, American
Birch
.41
.49-.60
.38-.39
.37
.64
.55-.65
.38
DAMPER CONTROL
Glass Doors
Butternut
Fully Open or
Fully Closed
Thisfireplaceisfittedwithamanuallycontrolled
chimney damper. The chimney damper should
be closed when the fireplace is not in use to
preventcoldairfromenteringthehomethrough
the chimney system.
Cherry, Black
Chestnut, American
Cottonwood
Elm
Hackberry
Hickory, Pecan
Hickory, True
Honey locust
Locust, Black
Magnolia
Maple
Oak, Red
Oak, White
Poplar
Sassafras
.50
.43
(Bi-Fold Doors)
Figure 3
.34-.40
.60.63
.53
.60.66
.69-.75
.66 (est.
.69
.48-.50
.48-.63
.59-.67
.64-.88
.42
.42
.52
.49
.64 (est.
.50
CAUTION
If a smoking condition exists,
glass doors should be closed
during fireplace operation.
The damper is controlled through the use of a
control lever located within the firebox open-
ing at the top center in front of the firebox
lintel (Figure 2). The control lever snaps into
place at either extreme of its range of motion.
When locked in position all the way Down (to
the front), the damper is Open. When locked
in position all the way Up (to the rear), the
damper is Closed.
Care and Cleaning of Your Glass Doors
Never clean the glass when the doors are hot.
Do not use ammonia or ammonia based glass
or household cleaner to clean the glass or the
door frame. An ammonia based cleaner will
damage the finish of the glass door.
Sweet gum
Sycamore, American
Tanoak
The appliance flue damper must always remain
open when operating.
Tupelo
Walnut, Black
Willow, Black
.55
.39
Clean the glass doors by wiping with a damp
towel followed by a clean dry towel to remove
streaks.
Damper
Closed
Damper
Open
SOFTWOODS
DENSITY
Remove stubborn stains from the glass with a
mild soap solution and a towel dampened with
clean water. Dry with a clean dry towel.
• The fire must always be confined within the
boundaries of the fuel grate.
Bald cypress
Cedar
Douglas Fir
Fir
Hemlock
Larch, Western
Pine
Redwood
Spruce
.46
Lintel
.31-.47
.46-.50
.32-.43
.40-.45
.52
.39-.59
.35-.40
.35-.41
.53
Combustion
Air Actuator
• Thefireplacescreensmustalwaysbeclosed
whenever the fireplace is being used.
•
Never slam the glass door since it could
cause the glass to break.
Figure 2
• Do not build excessively large or hot fires
— scorching or discoloring of the solid
brass or plated brass trim may occur.
Tamarack
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Extreme temperature changes can cause
glass breakage — do not build a hot fire and
close the glass doors if the doors are cold.
Combustion Air Control
IMPORTANT
Theactuatorforcombustionairsystemisstan-
dard on all fireplaces but must not be operated
if the complete system is not installed. See
Figure 4 and refer to Figure 2.
The lacquer coating on the pol-
ished brass glass doors can be
damaged or removed causing
corrosion and/or tarnish. To
help protect the solid brass; use
a non-acidic wax and avoid the
over-sprayofacidic/alkalibased
glass cleaners on the brass
pieces. If the solid brass begins
to turn black, all the protective
coating should be removed and
the metal re-polished, either
by hand or professionally. Sub-
sequently, the finish will not be
as “bright” or lustrous without
the protective coating. Solid
polished brass will acquire a
patina over years of use. This
is a normal occurrence and can
be polished.
•
If the tempered glass pane becomes
scratchedorchipped,itcreatesaweaknessin
the glass which can cause the glass to break
when heated. Replace the entire glass door
as an assembly by contacting your nearest
dealer.
If you have reason to believe that you do not
have a complete outside combustion system,
contact your distributor to have your fireplace
inspected for the presence of the complete
system before you use the combustion air
actuator. DO NOT assume that you have this
system in place because you have an actuating
lever present on your fireplace front face.
CAUTION
Glass,metalframes,handlesand
other components of the fireplace
get hot. Use handles and wear
thermalinsulatingglovesorother
effectiveprotectionortooltoopen
and close the doors or screens.
WARNING
Do not operate the combustion
air gate actuator unless a com-
plete outside combustion air
vent system has been installed
with your Fireplace.
WARNING
Be aware that safety glass is
unpredictable when hot and
may break, expelling hot glass
into the room. Advise all family
members to remain well away
from the fireplace when operat-
ingwithdoorsclosedtoavoidany
possible personal injury.
To provide outside combustion air to your
fireplace while it is in operation, locate the
combustion air actuator along the right side of
the fireplace opening behind the screen.
COMBUSTION AIR
Aproperamountofcombustionairisimportant
for your fireplace. Fireplaces consume large
amounts of oxygen. It is important to allow
an adequate supply of air. This fireplace is
equipped with an outside air kit, to provide suf-
ficientamountsofcombustionairfromoutside
of the house or structure in which it is installed.
With the outside combustion air kit closed, the
fire may draw from an outside air source and
pull air in through the chimney. This may cause
smoke spillage into the room.
To operate, push the end of the actuator to the
left as shown in Figure 4, until it "pops" free of
its "locked" position. Pull the actuator forward
to open the combustion air door, and push it
back to close.
IMPORTANT
Plated polished brass glass
doors may have a plastic cov-
ering over all brass pieces for
protection during shipping and
handling. The plastic covering
should be removed after instal-
lation of the fireplace before its
use. Under the plastic covering
is a protective lacquer coating
whichshouldnotberemoved.In
someinstances,ifitisremoved,
irreversibledamagetothebrass
finish could occur. Refer to the
following for specific informa-
tion on plated polished brass.
Please understand that the heat
of the fire will cause the protec-
tive lacquer finish to slightly
change to a light caramel color.
Do not be alarmed as this is a
normal occurrence.
Air Gate Kit (purchased separately)
Combustion Air Actuator
Smoke spillage often occurs when a fire is first
started, until the fireplace and the chimney has
hadtheopportunityto“comeuptotemperature”
and to begin to function normally. If smoke
spillage problems persist, a window may be
opened just a crack to allow the proper flow
of combustion air to the fireplace.
Your fireplace is equipped with an outside
combustion air kit, keep it open at all times
when fire is burning and close when fire is out
to prevent cold air intrusion.
Pull Forward to Open,
Push Back to Close
Figure 4
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TWICE A YEAR CHECK-UP
REFRACTORIES
CREOSOTE FORMATION AND REMOVAL
All fireboxes contain a furnace refractory floor,
sidesandback.Theserefractoriesarereinforced
with steel, but can be broken by improper use.
Dropping logs on the bottom refractory and
building fires directly against the refractories
can cause premature burnout of these com-
ponents. It may easily be repaired or replaced
at costs far below repair and maintenance for
masonry fireplaces.
Normally, twice a year, you should inspect your
fireplace following this list:
When wood is burned slowly, it produces tar
and other organic vapors, which combine
with expelled moisture to form creosote. The
creosote vapors condense in the relatively
cool chimney flue of a slow-burning fire. As
a result, creosote residue accumulates on the
flue lining. When ignited, this creosote makes
an extremely hot fire.
1. Inspect the opening in your chimney top
and remove any debris that could clog it.
The cap is usually held in place by four (4)
screws, which remove easily for checking
or cleaning the full length of the flue from
above. Remove the chimney top while
wearing gloves to guard against any sharp
metal edges.
2. Inspect the entire flue from the top down
forobstructionssuchasbirdsnests, leaves,
etc. This may be done by using a flexible
handled chimney cleaning brush. If the
chimney contains offset/return elbows; a
softbrushcleaningfromthetopdowntoany
elbow and then from the firebox up to the
offset/return section is the proper method.
The beam from a powerful flashlight will
help in this inspection.
Proper care and “burn-in” of the firebox will
prolong the period of enjoyment without ex-
tensive maintenance. For the first few uses,
build small fires – not roaring infernos. The
materials used in the refractories contain and
absorb moisture. It is important to “cure” the
refractoriesbybuildingonlymodestfires.Under
normalusage, itisexpectedthathairlinecracks
will appear in the refractory surface. These
hairline cracks do not affect the safe operation
of the fireplace.
The chimney should be inspected at least twice
yearly during the heating season to determine
if a creosote build-up has occurred.
If creosote has accumulated, it should be re-
moved to reduce the risk of a chimney fire.
Ifcreosotebuild-upisfound, donotusechemi-
cal chimney cleaners that are poured on a hot
fire. The chemical cleaners can be dangerous
and generally only work on the flue section
nearest the fire, leaving the rest of the flue
unaffected. It is best to take the time to clean
the flue as previously described or have the
chimney professionally cleaned by a qualified
chimney sweep.
Refractories should be replaced when:
3. Look up from inside the fireplace (damper
open) to see any obstructions in the lower
flue area. If present, shut the damper and
glass doors (if installed) to seal the firebox
and contain any soot that might fall.
1. The crack opens more than 1/4" (19 mm).
2. Pitting in the surface is extensive and pits
become deeper than 3/16" (4.76 mm).
3. Any piece of refractory larger than 2" (51
mm) in radius and 3/16" deep becomes
dislodged.
TROUBLESHOOTING
No Smoking Allowed
If your do not have glass doors installed, a
damp sheet covering the fireplace opening
and sealed with masking tape will do. Then
clean the flue from the top down (if an offset
system,cleanperStep2)usingapropersize
chimney brush with flexible pole sections.
Don’t open the doors or remove the sheet
until all soot has settled. Vacuum, don’t
sweep.
If conditions 1, 2 or 3 occur, the refractory
should be replaced.
Your new fireplace is designed not to smoke if
properlyinstalledandoperatedperourinstruc-
tions. If you do experience a problem, here are
several things to check:
MAINTENANCE GUIDELINES
Yourfireplaceisdesignedtooperatetrouble-free
with minimum maintenance. However, like any
fine appliance, it deserves and requires some
housekeeping attention.
1. Remember – always check to ensure your
flue damper is in the open position before
lighting a fire!
4. Check the metal flashing and seals around
your chimney. Seal any cracks or loose
nailhead openings to prevent roof leaks.
5. Clean the firebox thoroughly by using a soft
brush or equivalent.
Yourfireplacewillperformbetter–andcertainly
look more attractive to family and friends – if
it is cleaned before each use. Before the first
seasonal use in Autumn and after the last fire
in Spring, it is important to inspect the fireplace
system carefully. We recommend at least two
complete fireplace inspections a year.
2. When lighting your fire, a little smoke may
escape into the room – more likely if the
chimney is cold. To correct this, hold a
lightednewspaperupinsidethefireboxnear
the open flue damper. This will turn around
any downdraft and clear the flue of cold air.
As your log fire burns below, the updraft will
improve as the chimney heats up.
3. Is your fire too far forward? Move it toward
the back with your poker. Keep the fire well
within the confines of your fuel grate.
4. Keep your fire up on the grate and the re-
fractory below free of excessive ashes. The
fire needs plenty of air movement around
the logs.
5. If smoking occurs an hour or two after
lightingthefire,perhapsyourwell-insulated
houseistooairtightandthereisscarcelyany
wayforreplacementairtoenterandfeedthe
fire.Checktoseeifyouroutsidecombustion
air kit (if installed) is open. Check outside
to ensure no obstructions are in front of
exterior air entry. Open a window slightly,
open doors to one or two rooms and see if
this stops the smoking.
WARNING
Before Each Use
Continuedoverfiringcanperma-
nently damage your fireplace
system. Some examples of
overfiring are:
1. Clean the firebox of excessive ashes. Some
ownersprefertoleaveasmalllayertoinsulate
the cold refractory below the grate which
helps fire starting.
• Burning quantities of scrap
lumber, pine branches, paper
or cardboard boxes which ex-
ceedthevolumeofthenormal
log fire.
• Burning trash, chemicals or
chemically treated combus-
tibles.
This fireplace has a factory supplied grate
attached, it is permissible to remove the
grate for cleaning; however, the grate must
be re-attached to the fireplace before the
next burn.
2. Keepthefireplacescreenscleansocombus-
tion air flows freely.
3. Spotcheckthebrick-likerefractoryforsmall
cracks. Heatfromthefireexpandsitslightly.
When it cools, it contracts.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Is a vent fan, exhaust hood or central heating/cooling system stealing combustion air from your
fireplace? If their volume is high enough, this can cause negative pressure and an unwanted down-
draft – and smoking.
ACCESSORY COMPONENTS
7. Is your wood fuel too wet or unseasoned?
Or does it contain some chemical substance that causes sputtering, smoking and toxic fumes?
8. Figure 5 illustrates the correct height of your chimney top. It is unlikely that your installation
does not adhere to the installation instructions. However, if not correct, you could experience an
unusual downdraft. Usually, the best solution is to increase the chimney height. This may also be
necessary if nearby trees, adjoining roof lines or a hill is causing a downdraft condition.
9. Remember, your fireplace is not intended to heat your entire home.
Less Than 10'
2' Min.
3'
Min
10'
3'
Min
Bi-Fold Doors
20M30
FDBD36-B
Bi-Fold Doors
Your fireplace is fitted standard with beautiful bi-fold
doors. Model FDBD36-B doors have a handsome
bright brass finish.
Figure 5
REPLACEMENT PARTS
WARRANTY
To ensure warranty and to prevent a potential
fire hazard, do not use any other doors on these
appliances.
A complete parts list is found at the end of
this manual. Use only parts supplied from the
manufacturer.
• Thisfireplaceiscoveredbyalimitedwarranty
detailed separately from this document.
• Retain this manual. File it with your other
documents for future reference.
Normally, all parts should be ordered through
yourSuperiordistributorordealer. Partswillbe
shipped at prevailing prices at time of order.
PRODUCT REFERENCE INFORMATION
Ifyouencounteranyproblemsorhaveanyques-
tions concerning the installation or application
ofthissystem,pleasecontactyourdistributoror
installer.ForthenumberofyournearestSuperior
dealer, please call 1-800-953-6669.
When ordering repair parts, always give the
following information:
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
LHP
1110 West Taft Avenue
Orange, CA 92865
Brass Exterior Trim Kit
19M16
FETK36-B
Exterior Trim Kit
A decorative exterior trim kit is available for use with
this fireplace. This kit is designed to attach to the
fireplace front face around the firebox opening. It is
available in a beautiful bright brass finish to provide
adramaticenhancementtotheappealofthefireplace
in the home. (ref. Form #750,113M)
Your Fireplace's Model Number________________________________________
Your Fireplace's Serial Number ________________________________________
The Date On Which Your Fireplace Was Installed___________________________
Your Dealer's Name ________________________________________________
ON/OFF Wall
Switch Kit
ACCESSORY COMPONENTS
This ON/OFF wall switch kit
can be used in place of the
standardvariablespeedwall
switch (see Page 8). This
switchprovidessinglespeed
ON/OFF operation of the
blower. Install the ON/OFF
wall switch in a convenient
location near the fireplace.
Louver Kit
A decorative louver kit is available to enhance and
beautify the front face of your fireplace. This kit is
designed to attach directly to the fireplace front face
over the standard louvers. They are available in a
bright brass finish. (ref. Form #750,112M)
White Wall Switch Kit
Brass Louver Kit
19M15
FLK36-B
Cat. No.
85L87
Model No.
FWSK
Description
Set of 6
Louvers
ON/OFF Wall Switch Kit
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - MODEL HCD36MH
2
4
3
5
1
6
8
I
11
Variable Speed Wall
Mounted On/Off Switch.
Included w/FBK-200 Only
(or sold separately).
Blower
10
9
No
Description
Part No.
-
Qty.
-
Fireplace Assembly
36L89
H3610
88L72
2
2
1
1.
2.
3.
Firescreen
Rod, Screen
Refractory, Side, Right
LB-98316B
1
4.
Refractory, Side, Left
LB-98317B
LB-98315B
87L26
1
1
1
1
1
1
1
5.
6.
Refractory, Rear
Refractory, Bottom
Grate
7.
8.
Paint, Touchup, Black, FTPK-B
Blower, FBK-100, Single Speed (blower only)
H4353
9.
80L84
10.
11.
Blower, FBK-200, Variable Speed (blower & wall rheostat)
Wall Rheostat (Variable Speed Wall Switch)
80L85
045571H
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your
local distributor for fireplace code information.
LHP
Printed in U.S.A. © 2006 by LHP
1110 West Taft Avenue
Orange, CA 92865
P/N 725,038M REV. A 03/2006
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|