I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
All-Weather Articulating Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SB-WM46
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
SB-WM46
DIMENSIONS
7.87
200.0
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-WM46
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
SB-WM46
TOOLS REQUIRED FOR INSTALLATION
1/2" (12.7mm)
#2
1/4" (6.4mm)
3/8" (9.5mm)
7/16" (11.1mm)
1/2" (12.7mm)
PARTS
B (2)
[faceplate bracket]
C (2)
D (2)
[short interface
bracket]
[long interface bracket]
A (1)
[main assembly]
F (4)
[backing plate]
H (1)
5/32"
E (1)
[faceplate]
G (4)
[cable cover]
I (1)
3/16"
K (12)
1/4" x 5/8"
L (13)
1/4"
R (8)
#8-32 x 3/8"
M (4)
1/4"
Q (1)
5/16"
N (1)
1/8"
P (1)
1/4"
J (1)
7/32"
X (4)
V (4)
#10-32 x 1 1/8"
W (4)
[spacer]
Y (4)
3/8"
3/8" x 2 1/2"
T (4)
[cover plate]
S (4)
[concrete anchor]
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-WM46
Installation Instructions
Concrete Installation
ASSEMBLY and INSTALLATION
Install Arm Assembly/Wall Plate to Wall
Wood Stud Installation
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
IMPORTANT ! : The SB-WM46 mounts are designed to be
mounted to an 8" concrete wall.
1. Level wall plate and mark locations of pilot holes. (See
Figure 2)
IMPORTANT ! : The SB-WM46 mounts are designed to be
mounted to a 2" x 4" wood studs (16" on center) wall.
2. Drill 3/8" (9.5mm) diameter holes into concrete. (See Figure
2)
1. Level arm assembly/wall plate (A) and mark locations of
pilot holes. (See Figure 1)
3. Install anchors (S) into holes. (See Figure 2)
2. Drill 1/4" (6.4mm) diameter pilot holes into wood supports.
(See Figure 1)
CAUTION: Do not overtighten lag screws (X)!
3. Install 3/8 X 2 1/2" lag screws (X) through flat washers (Y),
arm assembly/wall plate (A), into wood supports. (See
Figure 1)
4. Install 3/8 x 2 1/2" lag screws (X) through flat washers (Y),
wall plate (A), into anchors (S). (See Figure 2)
1
x 4
1
x 4
x 4
2
1/4" (6.4mm)
(A)
x 4
2
3/8" (9.5mm)
(Y) x 4
(S) x 4
3
(Y) x 4
3
(X) x 4
9/16" (14.3mm)
4
(X) x 4
9/16" (14.3mm)
Figure 1
Figure 2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
SB-WM46
Cover Plate Installation
1. Install four cover plates (T) using four 10-32 x 1 1/8" Phillips
pan machine screws (V) and four spacers (W). Insert screw
into cover plate and add the spacer before inserting the
cover plate tab into the arm assembly/wall plate. (See
Figure 3)
x 4
2
Place tab
into slot
(T) x 4
(W) x 4
Figure 4
(46" or 55" models)
level with top of washers
Figure 3
Installing Interface Brackets to Display
1. Place display face down on a soft, non-abrasive surface.
2. Remove four sets of bolts and washers that were shipped
attached to the back of the display. Set hardware aside for
re-use. (See Figure 4)
WARNING: The bolts and washers are designed to be
permanent fixtures on the television. Never remove the bolts
or washers except for installation of the wall mount! Always
replace bolts immediately. Installing the television without the
bolts and washers may result in serious personal injury and/
or damage the television!
(D) x 2
just above rubber sealing gasket
(65" models)
level with top of washers
3. Place interface brackets (C or D) on the back of the display
so that they align with the holes on the display. Use
removed screws and washers to loosely attach interface
brackets to display. (See Figure 5)
NOTE: Use short brackets (D) if installing to 46" or 55" models
and long interface brackets (C) if installing to 65"
models.
4. Align bottom of the brackets with rubber sealing gasket and
the top of the brackets with the top of the washer. (See
Figure 5)
(C) x 2
just above rubber sealing gasket
Figure 5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-WM46
Installation Instructions
5. Use four removed screws and washers to secure interface
brackets (C or D) to back of display. (See Figure 6)
7/16" (11.1mm)
(M) x 4
2
(65" model shown)
x 4
5
(L) x 4
(K) x 4
2
(C or D) x 2
Figure 8
Figure 6
Install Faceplate Brackets to Faceplate
Install Faceplate to Display
1. Align faceplate brackets (B) with interface brackets (C or D),
aligning the middle thumb screw on bottom of display with
the faceplate bolt. (See Figure 9) and (See Figure 10)
1. Align faceplate brackets (B) with faceplate (E) and slide into
position. (See Figure 7)
faceplate bolt
1
1
(B) x 2
(E)
middle thumb screw
Figure 7
Figure 9
2. Using hex key (H), install four 1/4 x 5/8" button head cap
screws (K) through four 1/4" washers (L), faceplate (E),
faceplate brackets (B), into four 1/4" nuts (M). Tighten
securely. (See Figure 8)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
SB-WM46
(F) x 4
1
(L) x 8
(B) x 2
(K) x 8
2
Figure 10
2. Using hex key (H), install eight 1/4 x 5/8" screws (K) through
eight 1/4" washers (L) and faceplate brackets (B) into four
backing plates (F). Tighten securely. (See Figure 10)
1
Display Installation
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the SB-WM46 up to (and
including) the display does not exceed 150 lbs (68 kg).
(E)
1/2" (12.7mm)
(Q)
2
1. Align slots on upper portion of faceplate (E) with tabs on
upper portion of arm assembly (A). Lower display into
place, pivoting threaded stud on faceplate (E) into slot on
arm assembly (A). (See Figure 11)
2. Install spacer (N), washer (P), and nut (Q) onto threaded
stud. Tighten securely. (See Figure 11)
(A)
(N)
(P)
Figure 11
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-WM46
Installation Instructions
Extension and Swivel Tension
Cable Management
WARNING: Excessive loosening or tightening of
adjustment screws can result in serious personal injury or
damage to equipment!
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of covers (G) or screws (R).
1. Using hex keys (I, J), loosen or tighten adjustment screws
as required to achieve desired tension. (See Figure 14)
1. Carefully insert cables into cavities located in lower portions
of mount arms. (See Figure 12)
2. Install each cover (G) with two screws (R). (See Figure 12)
1
1
(G) x 4
(R) x 8
2
1
9/16" (14.3mm)
Figure 12
Adjustments
Pitch
1. Loosen pitch adjustment knob. (See Figure 13)
2. Tilt display to desired angle (-15° to +15°). (See Figure 13)
3. Tighten pitch adjustment knob. (See Figure 13)
1
-15°
Figure 14
2
0°
3
+15°
Figure 13
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
SB-WM46
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-WM46
Installation Instructions
SunBriteTV, LLC
2001 Anchor Court
Thousand Oaks, CA 91320
866-357-8688
8800-002156 Rev00
04/12
Download from Www.Somanuals.com. All Manuals Search And Download.
|