3ZZ9990184
(英・露・亜)
Download from Www.Somanuals.com. All Manuals Search And Download.
FOREWORD
Thank you for purchasing a Robin generator.
This manual covers operation and maintenance of the Robin generators.
All information in this publication is based on the latest production
information available at the time of approval for printing.
Pay special attention to statements preceded by the following words:
WARNING
Indicates a strong possibility of severe personal injury, loss of life and
equipment damage if instructions are not followed.
［CAUTION］
Indicates a possibility of personal injury or equipment damage if instructions
are not followed.
NOTE:
Gives helpful information.
If a problem should arise, or if you have any questions about the generator,
consult an authorized dealer or service shop
WARNING
■
The generator is designed to give safe and dependable service if
operated according to instructions.
■
Do not operate the generator before you have read and
understood the instructions. Failure to do so could result in death,
personal injury or equipment damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1. SAFETY PRECAUTIONS・・・・・・・・・・・・・・・・・・・・・・1
2. SPECIFICATIONS・・・・・・・・・・・・・・・・・・・・・・・・・・3
3. COMPONENTS ・・・・・・・・・・・・・・・・・・・・・・・・・・・4
4. PRE-OPERATION CHECKS ・・・・・・・・・・・・・・・・・・・・7
5. OPERATING PROCEDURES・・・・・・・・・・・・・・・・・・・・10
6. WATTAGE INFORMATION ・・・・・・・・・・・・・・・・・・・・・17
7. MAINTENANCE SCHEDULE・・・・・・・・・・・・・・・・・・・・19
8. "HOW-TO" MAINTENANCE ・・・・・・・・・・・・・・・・・・・・20
9. PREPARATION FOR STORAGE・・・・・・・・・・・・・・・・・・22
10. TROUBLESHOOTING ・・・・・・・・・・・・・・・・・・・・・・・23
11. WIRING DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・24
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY PRECAUTIONS
Please make sure you review each precaution carefully.
WARNING
Do not operate the generator near gasoline or gaseous fuel because of the
potential danger of explosion or fire.
Do not fill the fuel tank with fuel while the engine is running. Do not smoke or
use open flame near the fuel tank. Be careful not to spill fuel during refueling.
If fuel is spilt, wipe it off and let dry before starting the engine.
WARNING
Do not place in flammables near the generator.
Be careful not to place fuel, matches, gunpowder, oily cloths, straw, trash, or any other in flammables
near the generator.
WARNING
Do not operate the generator inside a room, cave, tunnel, or other
insufficiently ventilated area. Always operate it in a well-ventilated area,
otherwise the engine may become overheated, and the poisonous carbon
monoxide gas contained in the exhaust gases will endanger human lives.
Keep the generator at least 1 meter (3 feet) away from any structure or
1m
building during use.
1m
If the generator must be used indoors, the area must be well-ventilated and
extreme caution must be taken regarding the discharge of exhaust gases.
WARNING
Do not enclose the generator nor cover it with a box.
The generator has a built-in forced air cooling system, and may become overheated if it is enclosed.
If generator has been covered to protect it from the weather during non use, be sure to remove it and
keep it well away from the area during generator use.
WARNING
Operate the generator on a level surface.
It is not necessary to prepare a special foundation for the generator.
However, the generator will vibrate on an irregular surface, so choose a level place without surface
irregularities.
If the generator is tilted or moved during operation, fuel may spill and / or the generator may tip over,
causing a hazardous situation.
Proper lubrication cannot be expected if the generator is operated on a steep incline or slope. In such
a case, piston seizure may occur even if the oil is above the upper level.
WARNING
Pay attention to the wiring or extension cords from the generator to the connected device.
If the wire is under the generator or in contact with a vibrating part, it may break and
possibly cause a fire, generator burnout, or electric shock hazard.
Replace damaged or worn cords immediately.
Download from Www.Somanuals.co－m. A1l－l Manuals Search And Download.
WARNING
Do not operate in rain, in wet or damp conditions, or with wet hands.
The operator may suffer severe electric shock if the generator is wet due to rain or snow.
WARNING
If wet, wipe and dry it well before starting. Do not pour water directly over the generator, nor wash it
with water.
WARNING
Be extremely careful that all necessary electrical grounding procedures are followed during each and
every use. Failure to do so can be fatal.
WARNING
Do not contact the generator to a commercial power line. Connection to a commercial
power line may short circuit the generator and ruin it or cause electric shock hazard.
Use the transfer switch for connecting to domestic circuit.
WARNING
No smoking while handling the battery. The battery emits flammable hydrogen gas,
which can explode if exposed to electric arcing or open flame.
Keep the area well-ventilated and keep open flames/sparks away when handling the battery.
WARNING
Engine becomes extremely hot during and for some time after operation.
Keep combustible materials well away from generator area.
Be very careful not to touch any parts of the hot engine especially the muffler area
or serious burns may result.
WARNING
Keep children and all bystanders at a safe distance from work areas.
WARNING
It is absolutely essential that you know the safe and proper use of the power tool or appliance that
you intend to use. All operators must read, understand and follow the tool/appliance owners manual.
Tool and appliance applications and limitations must be understood. Follow all directions given on
labels and warnings. Keep all instruction manuals and literature in a safe place for future reference.
WARNING
Use only "LISTED" extension cords.
When a tool or appliance is used outdoors, use only extension cords marked "For Outdoor Use".
Extension cords, when not in use should be stored in a dry and well ventilated area.
WARNING
Always switch off generator's AC circuit breaker and disconnect tools or appliances when not in use,
before servicing, adjusting, or installing accessories and attachments.
［CAUTION］
Make sure the engine is stopped before starting any maintenance, servicing or repair.
Make sure maintenance and repair of the generator set are performed by properly trained personnel only.
－2－
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SPECIFICATIONS
RGX2900
RGX3600
RGX4800
MODEL
Brush-less, self-exciting, 2-poles, single phase
Condenser type
Type
Voltage regulating system
AC Output
Rated voltage-Frequency V-Hz
220-50, 240-50, 230-50, 120/240-60
50Hz
60Hz
50Hz
60Hz
2
2.4
3.5
4.1
4.1
4.8
Rated output
kVA (kW)
2.4
2.4
2.9
2.9
3
Maximum output kVA (kW)
3.6
1.0
Rated power factor
Safety device type
Fuse-less circuit breaker
DC Output
Rated voltage
V
A
12
Rated current
8.3
Safety device type
Fuse-less circuit breaker
EX17D
169
EX21D
EX27D
265
Model
Type
ROBIN, Air-cooled, 4-stroke, OHC
Displacement
Fuel
mL
211
Automotive Unleaded Gasoline
Fuel tank capacity
Rated continuous operation
L
16.6
50Hz
60Hz
12
9.5
7
6
H
10.5
8.4
1.0
Engine oil capacity
Spark plug
Starting system
Length
L
0.6
BR-6HS (NGK) (Champion; RL86C)
Recoil starter
580
420
480
48
605
450
500
54
650
510
540
70
mm
mm
mm
kg
Width
Hight
Dry weight
Specifications are subject to change without notice.
－3－
Download from Www.Somanuals.com. All Manuals Search And Download.
3. COMPONENTS
Engine switch
Fuel tank
Fuel strainer
(
)
Fuel cock
Control panel
Recoil starter
handle
Recoil starter
Fuel gauge
Oil gauge (oil filler)
Oil drain plug
Tank cap
Spark plug cap
Choke lever
Air cleaner
Muffler cover
Exhaust outlet
－4－
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
RGX2900
(50Hz-220V, 240V)
(60Hz-120/240V)
AC receptacle
AC receptacle
Voltmeter
Voltmeter
AC circuit
breaker
AC circuit
breaker
(
)
(
)
Earth ground
terminal
Earth ground
terminal
DC output DC circuit
DC output DC circuit
terminal
breaker
terminal
breaker
RGX3600
(50Hz-220V, 240V)
(60Hz-120/240V)
AC receptacle
AC receptacle
Voltmeter
Voltmeter
AC circuit
breaker
AC circuit
breaker
(
)
(
)
Earth ground
Earth ground
terminal
terminal
DC output DC circuit
DC output DC circuit
terminal
breaker
terminal
breaker
RGX4800
(50Hz-220V, 240V)
(60Hz-120/240V)
AC receptacle
Voltmeter
AC receptacle Full power
switch
Voltmeter
AC circuit
breaker
AC circuit
breaker
(
)
(
)
Earth ground
Earth ground
terminal
terminal
DC output DC circuit
DC output DC circuit
terminal breaker
terminal
breaker
Download from Www.Somanuals.co－m. 5Al－l Manuals Search And Download.
RGX2900
(50Hz-230V)
AC receptacle
Voltmeter
AC circuit
breaker
(
)
Earth ground
terminal
DC output DC circuit
terminal
breaker
RGX3600
(50Hz-230V)
AC receptacle
Voltmeter
AC circuit
breaker
(
)
Earth ground
terminal
DC output DC circuit
terminal
breaker
RGX4800
(50Hz-230V)
AC receptacle
Voltmeter
AC circuit
breaker
(
)
Earth ground
terminal
DC output DC circuit
terminal
breaker
－6－
Download from Www.Somanuals.com. All Manuals Search And Download.
4. PRE-OPERATION CHECKS
CHECK ENGINE OIL
Before checking or refilling oil, be sure
Oil filler cap
(Oil gauge)
generator is located on stable and level
surface with engine stopped.
■
Remove oil filler cap and check the
engine oil level.
Upper level
Lower level
■
If oil level is below the lower level line,
refill with suitable oil (see table) to
upper level line. Do not screw in the
oil filler cap when checking oil level.
■
Change oil if contaminated.
(See "How-To" Maintenance.)
Oil capacity (Upper level) :
(L)
RGX2900 . . . . . . . . . . . . . . . . . . 0.6
RGX3600 . . . . . . . . . . . . . . . . . . 0.6
RGX4800 . . . . . . . . . . . . . . . . . . 1.0
Recommended engine oil:
Use 4-stroke automotive detergent oil
of API service class SE or higher grade
(SG, SH or SJ is recommended). SAE
10W-30 or 10W-40 is recommended
for general, all-temperature use. If
single viscosity oil is used, select the
appropriate viscosity for the average
temperature in your area.
5W
10W
20W
#20
Single grade
#30
#40
10W
-30
Multigrade
10W
-
40
Ambient
temperature
Download from Www.Somanuals.co－m. A7l－l Manuals Search And Download.
CHECK ENGINE FUEL.
WARNING
Do not refuel while smoking or near open flame or other such
potential fire hazards. Otherwise fire accident may occur.
■
Check fuel level at fuel level gauge.
■
If fuel level is low, refill with
unleaded automotive gasoline.
LEVEL
■
Be sure to use the fuel filter screen
on the fuel filter neck.
Fuel tank cap
Fuel filter screen
Fuel Amount
up to "LEVEL" position
12.8 liters
FULL
EMPTY
WARNING
Make sure you review each warning in order to prevent fire hazard.
■
Do not refill tank while engine is running or hot.
■
Close fuel cock before refueling with fuel.
■
Be careful not to admit dust, dirt, water or other foreign objects Into
fuel.
■
Wipe off spilt fuel thoroughly before starting engine.
■
Keep open flames away.
－8－
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING COMPONENT PARTS
Check following items before starting engine:
■
Fuel leakage from fuel hose, etc.
■
Bolts and nuts for looseness.
■
Components for damage or breakage.
■
Generator not resting on or against any adjacent wiring.
CHECK GENERATOR SURROUNDINGS
WARNING
Make sure you review each warning in order to prevent fire hazard.
■
Keep area clear of in flammables or other hazardous materials.
■
Keep generator at least 3 feet (1 meter) away from buildings or other
structures.
■
Only operate generator in a dry, well ventilated area.
■
Keep exhaust pipe clear of foreign objects.
■
Keep generator away from open flame. No smoking!
■
Keep generator on a stable and level surface.
■
Do not block generator air vents with paper or other material.
GROUNDING THE
GENERATOR
■
To ground the generator to the earth,
connect the grounding lug of the
generator to the grounding spike
driven into the earth or to the
conductor which has been already
grounded to the earth.
Grounding spike
■
If such grounding conductor or
grounding electrode is unavailable,
connect the grounding lug of the
generator to the grounding terminal of
the using electric tool or appliance.
(
)
Earth ground terminal
Download from Www.Somanuals.co－m. A9l－l Manuals Search And Download.
5. OPERATING PROCEDURES
STARTING THE GENERATOR
CAUTION
［
］
Check the oil level before each operations as outlined by the article
"CHECK ENGINE OIL"
(a) Turn the Engine switch to the position
ON
"ON".
OFF
(b) Turn the AC circuit breaker to the
position "OFF".
ON
OFF
OFF
(c) Open the fuel cock.
CLOSE
CLOSE
OPEN
(d) Set choke lever to close if the engine
Choke lever
is cold.
CLOSE
OPEN
Download from Www.Somanu－als.1co0m－. All Manuals Search And Download.
(e) Pull the starter handle slowly until
resistance is felt.
This is the "compression" point.
Return the handle to its original
position and then pull swiftly.
■
If the engine fails to start after several
attempts, repeat above procedures
with choke lever returned to "OPEN"
position.
■
Do not fully pull out the rope.
■
After starting, allow the starter handle
to return to its original position while
still holding the handle.
(f) After the engine started, return the
choke lever gradually to "OPEN"
position.
Choke lever
CLOSE
OPEN
(g) Warm up the engine without a load for
a few minutes.
－11－
Download from Www.Somanuals.com. All Manuals Search And Download.
USING ELECTRIC POWER
WARNING
■
Make sure that the appliance is switched OFF before connecting it to
the generator.
■
Do not move the generator while it is running.
■
Be sure to ground the generator if the connected appliance is
grounded. Failure to ground unit may lead to electrical shock.
(1) AC APPLICATION
A
Single voltage type
(a) Check the voltmeter for proper
voltage.
■
This generator is thoroughly tested
Voltmeter
and adjusted in the factory.
If the generator does not produce the
specified voltage, consult your
nearest Robin dealer or service shop.
(b) Turn off the switch (es) of the electrical
appliance (s) before connecting to the
generator.
(c) Insert the plug (s) of the electrical
appliance(s) into the receptacle.
■
Check the amperage of the receptacles used referring to TABLE 1, and be
sure not to take a current exceeding the specified amperage.
■
Be sure that the total wattage of all appliances dose not exceed the rated
output of the generator.
Download from Www.Somanu－als.1co2m－. All Manuals Search And Download.
Up to total 15 ampere
from two receptacles
Up to 30 amperes
Up to 16 amperes
Up to 15 amperes
TABLE 1
WARNING
■
To take power out from the TWIST
LOCK RECEPTACLE, insert the
plug into the receptacle, and turn
it clockwise to the lock position.
TWIST
■
Be sure to ground the generator if
the connected electrical device Is
grounded.
NOTE :
When the AC circuit breaker turns off during operation, the generator is over
loaded or the appliance is defective. Stop the generator immediately, check the
appliance and / or generator for overloading or detect and have repaired as
necessary by Robin dealer or service shop.
(d) Turn the AC circuit breaker to the
ON
position "ON".
(e) Turn on the switch of the appliance.
OFF
ON
－13－
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Dual voltage type (RGX4800)
FULL POWER SWITCH
(a) Select the voltage using the FULL
POWER SWITCH in accordance with
the electrical appliance.
120V
240V
Refer to TABLE 2.
120V
CAUTION
［
］
Change the FULL POWER SWITCH
after turning the AC circuit breaker
to "OFF".
(b) Operate in the same way as step (a)
through step (d) of single voltage type.
NOTE :
Voltmeter always indicates the lower voltage whichever the FULL POWER
SWITCH is set.
Switch position
120V
Lower Voltage Receptacle
Activated full rated output
Activated half of rated output
TABLE 2
Higher Voltage Receptacle
N.A
120/240V
Activated full rated output
Download from Www.Somanu－als.1co4m－. All Manuals Search And Download.
(2) DC APPLICATION
The DC terminal is used only for charging
12 volt batteries.
Red
It provides up to 12V-8.3A (100W) of
maximum power.
Black
+
-
CONNECTION OF CABLE :
■
Connect positive (red) terminal on
generator to positive (+) terminal on
battery.
■
Connect negative (black) terminal on
generator to negative (
battery.
-) terminal on
■
Both AC and DC output can be used
at the same time if the total output is
within rated output of the generator.
SAFETY PRECAUTIONS WHILE CHARGING
■
An explosive hydrogen gas is discharged through vent holes in the battery
during the charging process. Do not allow spark or open flame around the
generator or battery during the charging process.
■
■
■
Electrolyte fluid can burn eyes and clothing. Be extremely careful to avoid
contact. If injured, wash the affected area immediately with large quantities of
water and consult a doctor for treatment.
When charging a large capacity battery or totally discharged battery, excessive
current may force the DC breaker to turn off.
In such cases, use a battery charger to charge a large battery with AC output.
Battery defects may cause the DC breaker to turn off.
Check the battery before replacing the DC breaker.
－15－
Download from Www.Somanuals.com. All Manuals Search And Download.
ON
STOPPING THE GENERATOR
(a) Turn off the power switch of the
electric equipment and unplug the cord
from receptacle of the generator.
OFF
OFF
(b) Turn the AC circuit breaker to the
"OFF" position.
ON
(c) Allow the engine about 3 minutes to
cool down at no-load before stopping.
(d) Turn the Engine switch counterclockwise
to the position "OFF".
OFF
(e) Close the fuel cock.
CLOSE
CLOSE
OIL SENSOR
OPEN
(a) The oil sensor detects the fall in oil
level in the crankcase and automati-
cally stops the engine when the oil
level falls below a predetermined level.
(b) When engine has stopped
automatically, switch off generator's
AC circuit breaker, and check the oil
level.
Oil sensor
Refill engine oil to the upper level as
instructed on page 6 and restart the
engine.
(c) If the engine does not start by usual
starting procedures, check the oil level.
Download from Www.Somanu－als.1co6m－. All Manuals Search And Download.
6. WATTAGE INFORMATION
Some appliances need a "surge" of energy when starting.
This means that the amount of electrical power needed to start the appliance may exceed
the amount needed to maintain its use.
Electrical appliances and tools normally come with a label indicating voltage, cycles / Hz,
amperage (amps) and electrical power needed to run the appliance or tool.
Check with your nearest dealer or service center with questions regarding power surge of
certain appliances or power tools.
■
Electrical loads such as incandescent lamps and hot plates require the same wattage
to start as is needed to maintain use.
■
Loads such as fluorescent lamps require 1.2 to 2 times the indicated wattage during
start-up.
■
Loads for mercury lamps require 2 to 3 times the indicated wattage during start-up.
■
Electrical motors require a large starting current. Power requirements depend on the
type of motor and its use. Once enough "surge" is attained to start the motor,
the appliance will require only 50% to 30% of the wattage to continue running.
■
Most electrical tools require 1.2 to 3 times their wattage for running under load during
use. For example, a 5,000 watt generator can power a 1800 to 4000 watt electrical
tool.
■
Loads such as submersible pumps and air compressors require a very large force to
start. They need 3 to 5 times the normal running wattage in order to start.
For example, a 5,000 watt generator would only be able to drive a 1,000 to 1,700 watt
pump.
NOTE :
The following wattage chart is general guide only. Refer to your specific appliance for
correct wattage.
To determine the total wattage required to run a particular electrical appliance or tool,
multiply the voltage figure of the appliance/tool by the amperage (amps) figure of same.
The voltage and amperage (amps) information can be found on a name plate which is
normally attached to electrical appliances and tools.
Applicable Wattage (W)
RGX2900
RGX3600
RGX4800
Applications
50Hz
60Hz
2400
1200
900
50Hz
60Hz
2900
1500
1100
650
50Hz
60Hz
4100
2100
1500
950
Incandescent lamp, Heater
Fluorescent lamp, Electric tool
Mercury lamp
2000
1100
800
2400
1200
900
3500
1800
1300
800
Pump, Compressor
500
550
550
－17－
Download from Www.Somanuals.com. All Manuals Search And Download.
VOLTAGE DROP IN ELECTRIC EXTENSION CORDS
When a long electric extension cord is used to connect an appliance or tool to the
generator, a certain amount of voltage drop or loss occurs in the extension cord
which reduces the effective voltage available for the appliance or tool.
The chart below has been prepared to illustrate the approximate voltage loss when
an extension cord of 300 feet (approx. 100 meters) is used to connect an
appliance or tool to the generator.
Nominal
cross
section
Allowable No.of strands
Resistance
A.W.G.
Current Amp.
current
/ strands dia.
mm2
0.75
1.27
2.0
No.
18
A
No./mm
30/0.18
50/0.16
37/0.26
45/0.32
70/0.32
1A 3A 5A 8A 10A 12A 15A
Ω/100m
7
2.477 2.5V 8V 12.5V
─
─
─
─
─
16
12
17
23
35
1.486 1.5V 5V 7.5V 12V 15V 18V
14
0.952
0.517
0.332
1V 3V 5V 8V 10V 12V 15V
3.5
12 to 10
10 to 8
1.5V 2.5V 4V 5V 6.5V 7.5V
1V 2V 2.5V 3.5V 4V 5V
─
─
5.5
Download from Www.Somanu－als.1co8m－. All Manuals Search And Download.
7. MAINTENANCE SCHEDULE
■
Check oil level.
DAILY
■
Check all components according to "PRE-
OPERATION CHECKS."
■
Wash cleaner element. -more often if used in
EVERY
dirty or dusty environments.
50 HOURS
■
Check spark plug, clean if necessary.
■
EVERY
Change engine oil. *-more often if used in
dusty or dirty environments.
100 HOURS
■
■
Adjust spark plug gap.
Clean fuel strainer.
EVERY
200 HOURS
■
■
Replace spark plug and cleaner element.
EVERY
Clean and adjust carburetor,valve clearance,
and valve seat along with cylinder head.
500 HOURS
■
■
■
■
■
Inspect control panel parts.
Check rotor and starter.
Replace engine mount rubber.
Overhaul engine.
EVERY
1,000 HOURS
(24 MONTHS)
Change fuel lines.
NOTE : (*)
■
Initial oil change should be performed after first twenty (20) hours of use.
Thereafter change oil every 100 hours.
■
Before changing the oil, check for a suitable way to dispose of the old oil.
Do not pour it down sewage drains, onto garden soil or into open streams.
Your local zoning or environmental regulations will give you more detailed
instructions on proper disposal.
－19－
Download from Www.Somanuals.com. All Manuals Search And Download.
8. "HOW-TO" MAINTENANCE
ENGINE OIL CHANGE
■
Change engine oil every 100 hours.
(For new engine, change oil after 20
hours.)
(a) Drain oil by removing the drain plug
and the oil filler cap while the engine
is warm.
(b) Reinstall the drain plug and fill the
engine with oil until it reaches the
upper level on the oil filler cap.
Oil drain plug
■
Use fresh and high quality lubricating oil to the specified level as directed on
page 7. If contaminated or deteriorated oil is used or the quantity of the engine
oil is not sufficient, the engine damage will result and its life will be greatly
shortened.
SERVICING THE AIR CLEANER
Maintaining an air cleaner in proper
condition is very important.
Element
Dirt induced through improperly installed,
improperly serviced or inadequate
Base
elements damages and wears out
engines. Keep the element always clean.
Air cleaner
cover
(a) Unhook the cover and remove the
cleaner element.
(b) Urethane form : Wash the element
with fresh water. Squeeze out the
water then dry the element.
(Do not twist.)
Element
Base
Air cleaner
cover
Download from Www.Somanu－als.2co0m－. All Manuals Search And Download.
CLEANING AND ADJUSTING
SPARK PLUG
(a) If the plug is contaminated with carbon,
remove it using a plug cleaner or wire
brush.
(b) Adjust the electrode gap to 0.6 to 0.7
mm (0.024 to 0.028 in.).
Gap 0.6 to 0.7 mm
(
)
0.024 to 0.028 in.
Spark plug :
BR-6HS (NGK) or RL86C (CHAMPION)
CLEANING FUEL STRAINER
Dirt and water in the fuel are removed by
the fuel strainer.
(a) Remove the strainer cup and throw
away water and dirt.
(b) Clean the screen and strainer cup
with gasoline.
(c) Tightly fasten the cup to main body,
making sure to avoid fuel leak.
－21－
Download from Www.Somanuals.com. All Manuals Search And Download.
9. PREPARATION FOR STORAGE
The following procedures should be followed prior to storage of your generator for
periods of 6 months or longer.
■
Drain fuel from fuel tank carefully by
disconnecting the fuel line.
Gasoline left in the fuel tank will
eventually deteriorate making engine-
starting difficult.
Drain screw
■
Remove the carburetor float chamber
and also drain the carburetor.
■
Change engine oil.
■
Check for loose bolts and screws,
tighten them if necessary.
■
Clean generator thoroughly with oiled cloth. Spray with preservative if
available. NEVER USE WATER TO CLEAN GENERATOR !
■
Pull starter handle until resistance is felt, leaving handle in that position.
■
Store generator in a well ventilated, low humidity area.
Download from Www.Somanu－als.2co2m－. All Manuals Search And Download.
10. TROUBLESHOOTING
When generator engine fails to start after several attempts, or if no electricity is
available at the output socket, check the following chart. If your generator still fails
to start or generate electricity, contact your nearest Robin dealer or service shop
for further information or corrective procedures.
When Engine Fails to Start :
Set the choke lever to "CLOSE"
position.
Check if choke lever is in its proper
position.
Check if fuel cock is open.
Check fuel level.
If closed, open fuel cock.
If empty, refill fuel tank making sure not
to overfill.
Check if engine switch is in OFF.
Turn engine switch to ON.
Check to make sure generator is not
connected to an appliance.
If connected, turn off the power switch
on the connected appliance and unplug.
Check spark plug for loose spark plug
cap.
If loose, push spark plug cap back into
place.
Check spark plug for contamination.
Remove spark plug and clean electrode.
When No Electricity Is Generated at Receptacle :
After making sure that the total wattage
of the electrical appliance is within
permissible limits and there are no
defects in the appliance, turn the AC
circuit breaker to the "ON" position.
If breakers continue to actuate, consult
your nearest servicing dealer.
Check to make sure AC circuit breaker
is in the "ON" position.
Check AC receptacle and DC terminals
for loose connection.
Secure connection if necessary.
Turn off switch on the appliance, and
disconnect cable from receptacle.
Reconnect after generator has been
started properly.
Check to see if engine starting was
attempted with appliances already
connected to generator.
－23－
Download from Www.Somanuals.com. All Manuals Search And Download.
11. WIRING DIAGRAM
RGX2900 (50Hz-220V, 240V)
ENGINE
CONTROL BOX
Wiring color code
Blk : Black
Blk/W : Black/White
Blu : Blue
LBlu : Light blue
Brn : Brown
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
Brn/W : Brown/White
Grn : Green
Grn/W : Green/White
Org : Orange
Gry : Gray
GENERATOR
AC circuit breaker
R
W
Y
: Red
Blk
R
Blk
AC output
: White
: Yellow
W/Blk : White/Black
Grn/Y : Green/Yellow
receptacle
Pur
: Purple
Blu
R
REC1
V
Voltmeter
Earth
(Ground)
terminal
REC1
Grn/Y
W
Brn
DC circuit breaker
Org
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser
Y
RGX2900 (60Hz-120/240V)
ENGINE
CONTROL BOX
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
GENERATOR
AC circuit breaker
Blk
Blk
AC output
REC3
receptacle
REC2
Blu
R
Blu
R
AC output
receptacle
W
Voltmeter
AC output
receptacle
V
AC circuit breaker
REC3
W
Grn/Y
Brn
DC circuit breaker
Org
Earth
(Ground)
terminal
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser
Y
Download from Www.Somanu－als.2co4m－. All Manuals Search And Download.
RGX3600 (50Hz-220V, 240V)
ENGINE
CONTROL BOX
Wiring color code
Blk : Black
Blk/W : Black/White
Blu : Blue
LBlu : Light blue
Brn : Brown
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
Brn/W : Brown/White
Grn : Green
Grn/W : Green/White
Org : Orange
Gry : Gray
GENERATOR
AC circuit breaker
R
W
Y
: Red
: White
: Yellow
Blk
R
Blk
AC output
W/Blk : White/Black
Grn/Y : Green/Yellow
receptacle
Pur
: Purple
Blu
R
REC1
V
Voltmeter
Earth
(Ground)
terminal
REC1
Grn/Y
W
Brn
DC circuit breaker
Org
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser
Y
RGX3600 (60Hz-120/240V)
ENGINE
CONTROL BOX
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
GENERATOR
AC circuit breaker
Blk
Blk
AC output
REC3
receptacle
REC2
Blu
R
Blu
R
AC output
receptacle
W
Voltmeter
AC output
receptacle
V
REC3
W
Grn/Y
Brn
DC circuit breaker
Org
Earth
(Ground)
terminal
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser
Y
－25－
Download from Www.Somanuals.com. All Manuals Search And Download.
RGX4800 (50Hz-220V, 240V)
ENGINE
CONTROL BOX
Wiring color code
Blk : Black
Blk/W : Black/White
Blu : Blue
LBlu : Light blue
Brn : Brown
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
Brn/W : Brown/White
Grn : Green
Grn/W : Green/White
Org : Orange
Gry : Gray
GENERATOR
AC circuit breaker
R
W
Y
: Red
: White
: Yellow
Blk
AC output
receptacle
W/Blk : White/Black
Grn/Y : Green/Yellow
Pur
: Purple
REC4
Blu
R
REC1
V
Voltmeter
AC output
receptacle
REC1
W
Grn/Y
Brn
DC circuit breaker
Org
Earth
(Ground)
terminal
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser Condenser
Y
RGX4800 (60Hz-120/240V)
ENGINE
CONTROL BOX
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
GENERATOR
AC circuit breaker
Blk
AC output
receptacle
AC output
receptacle
REC3
REC3
Blu
R
REC4
REC5
V
AC output
receptacle
AC output
receptacle
Voltmeter
W
Grn/Y
Brn
DC circuit breaker
Org
Earth
(Ground)
terminal
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser Condenser
Y
Download from Www.Somanu－als.2co6m－. All Manuals Search And Download.
RGX2900 / 3600 (50Hz-230V)
ENGINE
CONTROL BOX
Wiring color code
Blk : Black
Blk/W : Black/White
Blu : Blue
LBlu : Light blue
Brn : Brown
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
Brn/W : Brown/White
Grn : Green
Grn/W : Green/White
Org : Orange
Gry : Gray
GENERATOR
AC circuit breaker
R
W
Y
: Red
Blk
R
Blk
: White
: Yellow
W/Blk : White/Black
Grn/Y : Green/Yellow
Pur
: Purple
Blu
R
V
Voltmeter
AC output
Earth
(Ground)
terminal
receptacle
W
Grn/Y
Brn
DC circuit breaker
Org
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser
Y
RGX4800 (50Hz-230V)
ENGINE
CONTROL BOX
Ignition
coil
Oil sensor
control unit
IG
O.S
Engine switch
Blk
Blk
GENERATOR
AC circuit breaker
Blk
R
Blk
Blu
R
V
Voltmeter
AC output
Earth
(Ground)
terminal
receptacle
W
Grn/Y
Brn
DC circuit breaker
Org
+
Condenser
Winding
Diode stack
Assy
DC output
terminal
Brn
Y
Brn/W
-
Condenser Condenser
Y
－27－
Download from Www.Somanuals.com. All Manuals Search And Download.
|