OPERATION AND PARTS MANUAL
PLASTER/MORTAR MIXER
MS15H5.5 (Steel-Gasoline)
MS15E (Steel-Electric)
Effective S/N SED53
FINAL REVISION
Revision #2 (08/10/06)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
STOW MAIN OFFICE
Post Office Box 6254
Carson, Ca 90749
888-252-STOW
FAX:310-537-1986
Email: [email protected]
PARTS DEPARTMENT
800-427-1244
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX:310-537-4259
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
FAX:310-631-5032
FAX:310-537-1173
WARRANTYDEPARTMENT
800-421-1244, EXT.279
310-537-3700, EXT.279
SALES DEPARTMENT
310-661-4242
FAX:310-604-9237
877-289-7869(877-BUY-STOW)
© COPYRIGHT 2004, STOW CONSTRUCTION EQUIPMENT
STOW Construction Equipment and the STOW logo are registered trademarks of STOW and may not be used, reproduced, or
altered without written permission. All other trademarks are the property of thier respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should
remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are
based on the MS-15H/MS15E Plaster/Mortar Mixer. STOW Construction Equipment reserves the right to discontinue or change
specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
To find the latest revision of this
publication, visit our website at:
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MS15H/MS15E Plaster/
Mortar Mixer
HONDA GX160K1HX2 ENGINE
Cylinder Head Assembly ......................................... 48-49
Cylinder Barrel Assembly ........................................ 50-51
Crankcase Cover Assembly .................................... 52-53
Crankshaft Assembly .............................................. 54-55
Piston Assembly ..................................................... 56-57
Camshaft Assembly ................................................ 58-59
Recoil Starter Assembly ......................................... 60-61
Fan Cover Assembly ............................................... 62-63
Carburetor Assembly ............................................... 64-65
Air Cleaner Assembly .............................................. 66-67
Muffler Assembly .................................................... 68-69
Fuel Tank Assembly ................................................ 70-71
Flywheel Assembly ................................................. 72-73
Ignition Coil Assembly............................................. 74-75
Control Assembly .................................................... 76-77
Gear Reduction Assembly....................................... 78-79
Labels ...................................................................... 81-82
Here's How To Get Help ........................................... 3
Table Of Contents .................................................... 4
Parts Ordering Procedures ...................................... 5
Specifications ........................................................... 6
Dimensions .............................................................. 7
Safety Messages Alert Symbols ........................... 8-9
Rules For Safe Operation ................................. 10-12
Operation and Safey Decals .................................. 13
General Information ............................................... 14
Mixer Components................................................. 15
Engine Components .............................................. 16
Electric Motor .................................................... 17-18
Paddle Blade Adjustment ....................................... 19
Inspection.......................................................... 20-21
Start-up Procedures ......................................... 22-23
Shutdown Procedures............................................ 23
Maintenance (Engine)............................................ 24
Maintenance (Mixer) ......................................... 25-26
Troubleshooting (Engine).................................. 27-28
Troubleshooting (Mixer/Electric Motor) .................. 29
Electric Motor Wiring Diagram ............................... 30
Explanation of Code In Remarks Column.............. 32
Suggested Spare Parts .......................................... 33
Terms and Conditions Of Sale — Parts ........................ 83
Specification and part number
are subject to change without
NOTE
notice.
Component Drawings
Nameplate and Decals...................................... 34-35
Steel Tub Assembly ........................................... 36-37
Paddle Shaft Assembly ..................................... 38-39
Frame Assembly ............................................... 40-41
Engine Cover Assembly .................................... 42-43
Honda Engine Assembly................................... 44-45
Electric Motor Assembly.................................... 46-47
PAGE 4 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number
on hand when calling.
(Domestic USA Dealers Only)
STOW MAIN OFFICE
18910 Wilmington Ave.
Carson, CA 90746
800-421-1244
FAX: 310-537-3927
Extra Discounts!
All parts orders which include complete part numbers and
are received by our automated web parts order system, or
by fax qualify for the following extra discounts:
Email: [email protected]
Ordered
via
Standard
orders
Stock orders
SALES DEPARTMENT
310-661-4242
877-289-7869 (877-BUY-STOW)
PARTS DEPARTMENT
800-427-1244
310-537-3700
SERVICE DEPARTMENT
800-421-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
($750 list and above)
Fax: 310-604-9237
Fax
3%
5%
10%
10%
Web
FAX: 800-672-7877
FAX: 310-637-3284
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other
carrier.
FAX: 310-537-4259
FAX: 310-631-5032
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
**Common nuts, bolts and washers (all items under $1.00
list price) do not count towards the 10+ line items.
FAX: 310-537-1173
NOTE:DISCOUNTSARESUBJECTTOCHANGE
Direct TOLL-FREE access
to our Parts Department:
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
Toll-free nationwide — 800-427-1244
POST OFFICE BOX 6254
888-252-STOW[888-252-7869]
FAX:310-537-1986
CARSON, CA 90749
310-537-3700
FAX:800-556-1986
INTERNET:www.stowmfg.com
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
E-MAIL: [email protected]
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — SPECIFICATIONS
Table 1. MS15H/MS15E Mixer Specifications
Capacity
4.0 cu. ft (113 liters)
1-1/2 to 2-1/2 bags
380 lbs. (172 kg.)
348 lbs. (158 kg.)
Bag Capacity
Weight MS15H
Weight MS15E
Length w/Tow Bar x W x H
67 x 30 x 41 in.
(170 x 76 x 104 cm.)
Height W/Dump Handle
Discharge Height
Drive
47 in. (119 cm.)
7.5 in. (19 cm.)
V-Belt/Gear
Manual
Dump Action
Table 2. Specifications (Engine & Electric Motor)
Model
HONDA GX160K1HX2
BALDOR 35S772T980G1
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
1.0 HP, 115/230, Single
Phase Electric Motor
Type
2.70 in. X 1.80 in.
(68 mm x 45 mm)
Bore X Stroke
N/A
Displacement
Max Output
9.9 cu. in. (163 cc)
5.5 H.P./4000 R.P.M.
N/A
Engine/Electric Motor
1.0 H.P./1725 RPM
Approx. 0.95 U.S. Gallons
(3.6 Liters)
Fuel Tank Capacity
N/A
Fuel
Unleaded Gasoline
N/A
N/A
N/A
N/A
Lube Oil Capacity
Speed Control Method
Starting Method
0.63 qt. (0.6 liter)
Centrifugal Fly-weight
Type
Recoil Start
12.3 x 14.3 x 13.2 in.
(312 x 362 x 335 mm)
13.25 x 8.93 X 8.56 in.
(336 X 227 X 217 mm)
Dimensions (L x W x H)
Dry Net Weight
40.8 lbs. (15 Kg.)
Approx. 22 lbs. (10 Kg.)
PAGE 6 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — DIMENSIONS
TABLE 3. DIMENSIONS
Description
Dimensions in. (cm)
A
67 in. (170 cm)
B
C
C
50 in. (127 cm)
56 in. (142 cm)
56 in. (142 cm)
Figure 1. Dimensions
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Potential hazards associated with the operation of a MS-
15H/MS15E Plaster/Mortar Mixer will be referenced with
Hazard Symbols which appear throughout this manual, and
will be referenced in conjunction with Safety Message Alert
Symbols.
Lethal Exhaust Gas Hazards
WARNING
This Owner's Manual has been
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless
and odorless, and can cause death if
inhaled. NEVER operate this equipment
in a confined area or enclosed structure
that does not provide ample free flow air.
developed to provide complete
instructions for the safe and efficient
operation of the STOW Model MS-
15H/MS 15E mortar and plaster mixer.
Refer to the engine manufacturers
instructions for data relative to its safe
operation.
Before using this mixer, ensure that the operating individual
has read and understands all instructions in this manual.
Explosive Fuel
WARNING
SAFETY MESSAGE ALERT SYMBOLS
Hazards
Gasoline is extremely flammable, and its
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
Burn Hazards
WARNING
WARNING
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operations. Never operate
the engine with heat shields or heat guards
removed.
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Respiratory Hazards
WARNING
ALWAYS wear approved respiratory
protection when required.
PAGE 8 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — SAFETY MESSAGE ALERT SYMBOLS
Equipment Damage
Rotating Parts Hazards
CAUTION
CAUTION
Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
Accidental Starting Hazards
CAUTION
ALWAYS place the power source, circuit breakers or ON/
OFF switch in the OFF position, when the generator is not
in use, unless connected to transfer switch.
Eye and Hearing Hazards
CAUTION
ALWAYS wear approved eye and
hearing protection.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.
Read this manual!
DANGER
Failure to follow instructions in this manual may lead
to serious injury or even death! This equipment is to
be operated by trained and qualified personnel only!
This equipment is for industrial use only.
The following safety guidelines should always be used when
operating the STOW MS-40 mortar and plaster mixer:
■
■
High Temperatures – Allow the engine to cool before
adding fuel or performing service and maintenance
functions. Contact with hot! components can cause
serious burns.
GENERAL SAFETY
■
DO NOT operate or service this
equipment before reading this entire
manual.
The engine section of this mixer requires an adequate
free flow of cooling air. NEVER operate the mixer in any
enclosed or narrow area where free flow of the air is
restricted. If the air flow is restricted it will cause serious
damage to the mixer or engine
and may cause injury to people.
Remember the mixer's engine
■
■
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
gives off DEADLY carbon
monoxide gas.
■
■
ALWAYS refuel in a well-
ventilated area, away from
sparks and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
ALWAYS use extreme caution when working with
flammable liquids.When refueling, stop the engine and
allow it to cool. DO NOT smoke around or near the
machine. Fire or explosion could result from fuel vapors,
or if fuel is spilled on a hot engine.
NEVER operate this equipment under the influence of
drugs or alcohol.
■
■
NEVER operate the mixer in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the mixer.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
■
■
Stop the engine when leaving the mixer unattended.
Block the unit when leaving or when using on a slope.
Maintain this equipment in a safe operating condition at
all times.
■
■
■
■
NEVER place hands inside the drum while the blades
are rotating.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacture does not assume responsibility for any
accident due to equipment modifications.
WARNING
Starting the Mixer Engine
NEVER! start the engine or engage the paddle arms
when the drum is in the discharge (down) position.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 10 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — RULES FOR SAFE OPERATION
■
Depending on type of mixer, test the ON/OFF switch for
either the gasoline engine or electric motor before
operating.The purpose of these switches is to shut down
the engine or motor of the mixer
ALWAYS stand clear of the release drum lock. Move handle
downward to empty the drum. Move handle upward to return
to vertical position.Drum features automatic vertical locking
mechanism. Inspect for proper functionality before starting
engine or engaging blades. Any binding of material between
the mixing blades and drum will cause the handle to quickly
rotate if not in the "up and locked" position.
■
■
■
■
ALWAYS stop the engine before servicing, adding fuel
and oil.
NEVER run engine without air filter. Severe engine may
occur.
ALWAYS service air cleaner frequently to prevent
carburetor malfunction.
ALWAYS check the machine for loosened threads or bolts
before starting.
■
■
■
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using mixer.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children.
Stand Clear of the
Manual Dump Drum Handle
WARNING
■
■
DO NOT operate this equipment unless all guards and
safety devices are attached and in place.
Always stand clear of the dump handle when the mixer
is in operation.
CAUTION must be exercised while servicing this
equipment. Rotating and moving parts can cause injury
if contacted.
When towing, an adequate safety chain must be fastened
to the frame.SeeTowing Guidelines section in this manual.
Keep all inexperienced and unauthorized people away
from the equipment at all times.
Unauthorized equipment modifications will void all
warranties.
Check all fasteners periodically for tightness. Also check
towing tongue bolt, lock nut and wheel lug nuts for wear.
■
Refer to the HONDA Engine Owner's Manual for engine
technical questions or information recommended by
Multiquip for this equipment. Damage to the equipment
and/or injury to user may result.
■
■
■
■
■
■
TRANSPORTING
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
Drain fuel when transporting mixer over long distances
or bad roads.
■
Stop the engine and disconnect the spark plug before
allowing anybody’s hands in the mixing drum.
NEVER pour or spray water over the engine or electric
motor.
Stand Clear of the
Mixer when in use
WARNING
Always stand clear of the dump handle when the mixer
is in operation. Any binding of material between the mixer
blades and the drum will cause the drum handle to quickly
move and could cause bodily harm.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — RULES FOR SAFE OPERATION
MAINTENANCE
■
NEVER lubricate components or attempt service on a
running mixer.
■
ALWAYS allow the mixer a proper amount of time to
cool before servicing.
■
■
Keep the mixer in proper running condition.
Fix damage to the mixer immediately and always replace
broken parts.
■
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
EMERGENCIES
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
PAGE 12 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — OPERATION AND SAFETY DECALS
Machine Safety Decals
This STOW mixer is equipped with a number of safety decals (Figure 2). These decals are provided for operator safety and
maintenance information. The illustration below shows these decals as they appear on the mixer. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
Figure 2. Safety Decals
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — GENERAL INFORMATION
GENERAL
GASOLINE ENGINE CARE
The MQ STOW Model MS15H5.5 (Honda GX160K1HX2
gasoline engines) and MS15E (electric motor) plaster and mortar
mixers are shipped completely assembled and have been factory
tested.
For care and operation of the gasoline engine, refer to the engine
manufacturer’s operating instructions furnished with the engine.
We recommend draining and refilling the engine crankcase at
least every thirty hours of operation. Check the engine oil level
daily.
The drum batch capacity of these mixers is between 1.5 and
2.5 bags. With proper care, they will give continuous service
year-after-year.
GASOLINE MIXER OFF/ON SWITCH
This feature is on gasoline engine mixers only. Located on the
side of the engine cover. The purpose of this switch is to start
and stop the mixer in normal operation.
These mixers can be powered by either gasoline or electric
motors.The shaft of the engine or electric motor is connected to
a drive belt pulley which is attached to a main gear.As the main
gear rotates it causes the paddle shaft to rotate.
ELECTRIC MOTOR MIXER OFF/ON SWITCH
This feature is on electric motor mixers only.This switch is located
on top of the motor. Lift the engine cover to gain access to this
switch.The purpose of this switch is to start and stop the mixer in
normal operation. NEVER use the electric motor in an explosive
environment.
BEFORE STARTING
Before starting the engine, read the engine owners manual and
thoroughly understand the safety information.
Check the items listed below:
ENGINETHROTTLE AND CHOKE CONTROLS
OIL LEVELS
Please refer to the engine owners manual for specific instructions.
Be sure to check the oil levels in the engine and engine reduction
unit before starting the unit (gasoline model only).
HARDWARE
Check all hardware on the mixer before starting. Periodically
inspect all hardware. Loose hardware can contribute to early
component failure and poor performance. Use the torque chart
below as a general guideline and keep all hardware tight:
HARDWARE DIA
5/16"- 18
TORQUE (LB./FT.)
24
37
39
90
3/8" - 24
1/2" - 13
1/2" - 13 (Grade 8)
In accordance with our established
policy of constant improvement, we
reserve the right to amend these
specifications at any time without
notice.
PAGE 14 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — MIXER COMPONENTS
Figure 3. Mixer Compon
Figure 3 illustrates the basic components and controls of
the MS15H/MS15E mixer.
7.
8.
9.
Steel Mixing Drum — Mixing materials such as mortar,
plaster are to be placed into this drum for mixing. Always
clean the drum after each use.
1.
Engine Cover — Lift this cover to gain access to the engine
compartment.
2.
ON/OFF Switch (electric) — This switch is provided on
mixers with electric motors.To gain access to this switch,
lift the engine cover.When activated it will shut down the
electric motor.
Chock Blocks — Place these blocks (not included as
part of the mixer package) under each mixer wheel to
prevent rolling.
Mixing Paddles — Used in the mixing of material. This
unit uses four different types of paddles to provide a fast
uniform mix.
3.
4.
Bag Cutter—This feature allows compound mixing bags
to be opened easily, therefore allowing the contents of the
bag to fall directly into the mixing drum.
10. Tires — Replace tires with the recommended type tire of
Safety Grill — Provided for operator safety. This safety
grill is designed to keep hands and solid objects out of the
mixing drum when in use.This grill should be closed at all
times when mixer is in use. DO NOT remove the grill or
grill opening bar. Keep the grill clean by washing it down
daily.
12 x 3.
5.
6.
Dump Handle — Pull this handle downward to dump the
contents of the drum. Push the handle upward to return
the drum to its vertical position.
Pivot Point/Zerk Fitting — There is, on each end of the
mixing drum a zerk grease fitting.These fittings lubricate
the dumping mechanism. Lubricate both fittings at least
twice a week.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — BASIC ENGINE COMPONENTS
Honda GX Series Engine Shown
Figure 4. Engine Controls and Components
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
INITIAL SERVICING
the flow of fuel.
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
WARNING
WARNING
Operating the engine without an air
filter, with a damaged air filter, or a filter
NOTE
in need of replacement will allow dirt to
enter the engine, causing rapid engine
wear.
Adding fuel to the tank should be accomplished only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill,
DO NOT attempt to start the engine until the fuel residue has been
completely wiped up, and the area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch). Clean
spark plug once a week.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
PAGE 16 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — ELECTRIC MOTOR
Electric Motor
Electric MotorVoltage Switch
For maintenance care and operation of the electric motor, refer
to your electric motor instruction booklet furnished with the motor.
1.
ALWAYS make certain the motor switch is "OFF" and the
power cord has been disconnected from the power source.
2.
Remove the voltage lock-out bolt (Figure 2). Change the
position of the voltage change toggle switch from 115
VAC to 230 VAC. The mixer is factory wired for 115 VAC
operation.
Protect the electric motor from dust as much as possible and
keep ventilating openings clean.
Electric Motor
CAUTION
3.
4.
Replace the voltage lock-out bolt.
Safety
Important!, when changing the input voltage to the motor
from 115 to 230 VAC the plug on the motor power cord
must also be changed. See Table 3.
DO NOT spray water at any time on the electric motor.
DO NOT operate electric motor in a explosive environment.
The electric motor used in this mixer is a single-phase 1.0 HP
motor. The input voltage requirement for this motor is either 115
or 230 VAC only.
Table 3. Electric Motor Wiring Information
Motor
Horsepower
Rating
115-230 VAC - Single Phase
Electric Motor Connection
NEMA Plug Connector
Mating NEMA
Receptacle Connector
A 12 inch electrical cable (Figure 3) with a pigtail at one end is
provided with the electrical motor for hookup to a power source.
Table 2. shows the required NEMA connector for the desired
motor horsepower rating. In addition, Table 3 also shows the
matching NEMA approved connector for the required extension
cord.
1.0 HP
(115 VAC)
L5-20P P/N EM940537
L6-20P P/N 940539
L5-20R P/N EM940538
1.0 HP
(230 VAC)
L6-20R P/N 940540
ALWAYS, make certain that the power source required for the
electric motor is correct and always use the correct NEMA
configuration plug. Failure to supply the correct voltage to the
motor can severely damage the motor.
Table 4. Recommended Extension Cord Size
s
50 ft.
75 ft.
100 ft.
200 ft.
Model
Motor Voltage
(15.24 m) (22.86 m) (30.48 m)
(60.96 m)
The motor supplied is wired for 115 VAC grounded operation.
Make certain that the correct size grounded (3-wires) extension
cord is used.SeeTable 4.
115
No. 12
No. 14
No. 10
No. 12
No. 8
No. 6
No. 8
MS15E
(Electric)
1.0 HP
230
No. 12
Motors can burn out when the line voltage falls 10% below the
voltage rating of the motor. Failure to use proper voltage will
cause the motor to overheat and actuate the overload switch.
If overload protection should actuate because of improper voltage
or any other malfunction, turn the main switch on the motor to the
"OFF" position and correct the problem, press the reset switch
button, and turn the main switch to the "ON" position.
Electric Motor
Connections
CAUTION
ALWAYS make certain that the power source required
for the electric motor is correct and always use the correct
NEMA configuration plug. Failure to supply the correct
voltage to the motor can severely damage the motor.
It is strongly recommended that all
electrical wiring be done by a licensed
electrician.
NOTE
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — ELECTRIC MOTOR
Figure 5. Single Phase Electric Motor with 18 inch Pigtail Cable
PAGE 18 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — PADDLE BLADE ADJUSTMENT
Adjust paddles as shown in Figure 6.
Figure 6. Paddle Blade Adjustment, Steel Drum
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — INSPECTION
Before Starting
2. Remove the filler dipstick from the engine oil filler hole
(Figure 7) and wipe it clean.
1. Read all safety instructions at the beginning of manual.
2. Clean themixer, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check the air filter for dirt and dust. If air filter is dirty,
replace air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with
dry compressed air.
5. Check fastening nuts and bolts for tightness.
Eyesight and Hearing
CAUTION
Figure 7. Engine Oil Dipstick (Removal)
Protection
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
ALWAYS wear approved eye and
hearing protection before operating
the mixer.
4. If the oil level is low (Figure 8), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table7).Maximum oil
capacityis2.33qts. (1.09liters)
Inspection &
CAUTION
Maintenance Saftey
NEVER place hands or feet inside the
engine guard cover while the engine is
running. ALWAYS shut the engine down
before performing any kind of maintenance
service on the mixer.
Reference manufacturer engine
manual for specific servicing
nstructions.
Explosive Fuel
WARNING
Hazard
Failure to understand the operation of the WM-120 series
mixers could result in severe damage to the mixer or
personal injury.
See Figure 5 for the location of any control referenced in
this manual.
Figure 8. Engine Oil Dipstick (Oil Level)
Respiratory Hazard
CAUTION
Table 5. Oil Type
Temperature
NEVER operate the mixer in a confined
area or enclosed area structure that
does not provide ample free flow of air.
Season
Summer
Spring/Fall
Winter
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
25°C or Higher
25°C~10°C
0°C or Lower
PAGE 20 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — INSPECTION
Fuel Check
V-belt Check
A worn or damaged V-belt can adversely affect the
performance of the mixer. If a V-belt is defective or worn
simply replace the V-belt as outlined in the maintenance
section of this manual.
Explosive Fuel
Hazard
If your mixer has a gasoline engine, determine if the
engine fuel is low. If fuel is low, remove the fuel filler cap
and fill with unleaded gasoline. Motor
DANGER
Blade Check
fuels are highly flammable and can be
dangerous if mishandled.DO NOT smoke
while refueling.DO NOT attempt to refuel
the mixer if the engine is hot! or running.
Check for worn or paddle blades. Make sure that all blades
are adjusted properly. See blade adjustment procedure in
this manual. Replace all defective or damaged blades
immediately.
1. Remove the gasoline cap located on top of fuel tank.
Controls
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
Start/Stop Switches
This mixer has been equipped with a start/stop switch for
both the gasoline and electric motor mixers.These switches
should be tested every time the engine or electric motor is
started.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
Start/Stop Switch
CAUTION
Grease Fittings (Dumping Mechanism)
NEVER! disable or disconnect the start/stop switch. It is
provided for operator safety.Injury may result if it is disable,
disconnected or improperly maintained.
Check the zerk grease fittings at each end of the mixing
drum. These grease fittings lubricate the dumping
mechanism. If the dumping handle is stiff or hard to move
lubricate these fittings.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — START-UP PROCEDURES
2.
To start a cold engine, move the choke lever (Figure 10) to
the CLOSED position.
This section is intended to assist the operator with
the initial start-up of the MS-15H (gasoline) or
MS15E (electric) mixer.It is extremely important that
this section be read carefully before attempting to
use the mixer in the field.
DO NOT use your mixer until this section is thoroughly
understood.
CAUTION
Failure to understand the operation of the MS15H/MS15E mixers
could result in severe damage to the mixer or personal injury.
See Figure 3 for the location of any control referenced in this
manual.
Figure 10. Choke Lever
3.
Move the throttle lever (Figure 11) away from the slow
position, about 1/3 of the way toward the fast position.
Starting (gasoline only)
The following steps outline the procedure for starting the engine.
Depending on the type of engine employed in the mixer the
steps may vary slightly. If your mixer has an electric motor
disregard this section.
1.
Move the fuel shut-off lever (Figure 9) to the ON position.
Figure 11. Throttle Lever
Figure 9. Fuel Shut-OFF Lever
PAGE 22 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — START-UP PROCEDURES
Be sure to stand clear of the
dump handle when the mixer
is operational. Any binding of
material between the mixer
blades and the drum will cause
the drum handle to move to the
discharge position, thus
causing bodily harm.
4.
Turn the engine switch (Figure 12) to the ON position.
NOTE
Stopping the Mixer (Electric Motor)
1. Place the engine ON/OFF switch (Figure 14) in the
OFF position.
Figure 12. Engine ON/OFF Switch (ON)
7.
Pull the starter grip (Figure 13) lightly until you feel
resistance, then pull briskly.Return the starter grip gently.
Figure 14. Engine ON/OFF Switch (OFF)
2. Place the fuel shut-off valve in the OFF position.
3. Disconnect the spark plug wire.
4. Clean drum of all debris and foreign matter.
5. Store mixer in a clean dry location.
Figure 13. Starter Grip
Starting (electric only)
1.
Using an adequate size extension cord (see Table 4),
connect one end of the extension cord to the plug on the
electric motor, connect the other end to the power source.
Make sure the motor is configured for the proper operating
voltage.
DO NOT Disconnect
DANGER
the Start/Stop Switch
NEVER disable or disconnect the start/stop switch. It is
provided for operator safety. Serious Injury may result
if it is disabled, disconnected or improperly maintained.
2.
Set the electric motor's ON/OFF switch (Figure 5) to the
ON position.
Mixing Dumping
Stopping the Mixer (Electric Motor)
1.
2.
3.
The paddle shaft inside the drum should be rotating at this
1. Place the electric motor's ON/OFF switch in the OFF
time.
position.
Lift the mixing bag compound onto the steel grate over the
bag cutter and let the contents fall into the drum.
2. Disconnect the electric motor's extension cord from its
power source.
Add water, and mix compound to desired consistency.
3. Clean drum of all debris and foreign matter.
4. Store mixer in a clean dry location.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — MAINTENANCE (ENGINE)
UseTable 8 as a general maintenance guideline when servicing
your engine. For more detail engine maintenance information,
refer to the engine owner's manual supplied with your engine.
Table 8. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 24 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — MAINTENANCE (MIXER)
Drum Head Seals
Lubricating the
Grease Fittings
CAUTION
There is 1 set of drum head seals (Figure 15) that will require
lubrication.
Failure to lubricate the drum bearing grease fittings
periodically will cause the dumping mechanism to stiffen,
making the mixing drum hard to dump.
IMPORTANT- DRUM HEAD
CAUTION
SEAL CARE
Grease seals every 40 hours of operation using any grade
#1 lithium base grease. Apply grease until visible of mixing tub
(over grease).This will purge seal system of contamination.
Countershaft Bearing Lubrication
There is 1 set of countershaft bearings (Figure 17) that will
require lubrication. Lubricate the grease fitting for each
countershaft bearing every 40 hours of operation using
any grade lithium base grease.
Figure 15. Grease Fittings (Drum Head Seals)
Drum Bearing Bracket Lubrication
Figure 17. Grease Fittings (Countershaft)
There is 1 set of drum bearing brackets (Figure 16) that will
require lubrication. These brackets are intended to make
the drum rotate freely. Lubricate the grease fitting for each
drum bearing bracket every month or when the drum
becomes difficult to position using multi-purpose grade
grease.
Grease Fittings (Zerk) Maintenance (Electric Motor)
1.
There are two grease (Figure 18) fittings at each end of the
electric motor that will require lubrication. Lubricate these
fittings about every 16 months.
2.
Use Poleyrex EM (Exxon Mobil) or equalivant lubricant.
Clean grease fitting, apply grease gun to fitting (1/2 shot).
Remember too much grease or injecting grease too quickly
can cause premature bearing failure. Slowly apply the
recommended amount of grease, taking a miniute or so to
apply.
Figure 16. Grease Fittings (Dumping Mechanism)
Lubricating the
Figure 18. Grease Fittings Electric Motor
CAUTION
Zerk Grease Fittings
Failure to lubricate the zerk grease grease fittings
periodically will cause the dumping mechanism to stiffen,
making the mixing drum hard to dump.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — MAINTENANCE (MIXER)
MAIN GEAR AND DRIVE PINION ALIGNMENT
GEAR LUBRICATION
1.
2.
3.
Disconnect the spark plug wire (gasoline engines). If
mixer is equipped with an electric motor remove power
cord from AC power receptacle. In addition make sure
the clutch engagement lever is dis-engaged to relieve V-
belt tension.
The countershaft and drive pinion are mounted on a slotted
base.To align drive pinion with main gear, loosen the pillow
block mounting bolts and move them until the necessary
alignment has been made. Remember gears must be
paralleled aligned not skewed.
Using your hand, slightly move (rock) the drive pulley back
and forth to determine the amount of backlash. Insert feeler
gauge between gears to determine backlash distance.
Backlash should range between 0.007- 0.012 inches
(Figure 19).
The surface of the pinion and main gear (Figure 21) should be
very lightly greased.
Grease main and pinion gears
every 250 hours of operation.
IMPORTANT! avoid over-
greasing. Excess grease will
accumulate contaminates and
cause premature wear.
Figure 21. Pinion and Bull Gear Lubrication
CLEANING
Cleaning the Mixer
CAUTION
Always disconnect the spark plug wire before cleaning
the inside of the drum.
Figure 19. Drive Pinion and Main Gear (Backlash)
NEVER pour or spray water (Figure 22) over the gasoline
engine or electric motor.
INSPECT TOOTH CONTACT BETWEEN MAIN GEAR AND
DRIVE PINION
For consistent performance, long life and high quality
mixing, thoroughly clean the mixer inside and out at the
end of each day’s operation. To prevent lumps of dried
mortar from forming and contamination of future batches,
do not allow a buildup of materials to form on the blades
or anywhere inside the drum.
1.
Coat 3 or 4 teeth at 3 different positions on the main gear
with yellow paint.
2.
3.
4.
Rotate the drive pulley in both directions.
Inspect the tooth pattern.
If gear teeth are not contacting properly (Figure 20), adjust
pillow block to correct the problem.
Figure 20. GearTeeth Alignment
Figure 22. No Spraying of Water
PAGE 26 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER —TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
If the problem cannot be remedied, please leave the unit
just as it is and consult or company's service department.
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine, Mixer and Electric Motor
Troubleshooting (Tables 6, 7 and 8) information shown below
and on the proceeding pages.
TABLE 6. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is red?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Oil pressure alarm lamp blinks
upon starting?
Check Automatic shutdown circuit "oil sensor".
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Engine will not turn over?
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged? Replace cylinder head gasket.
Insufficient power output "no
compression"
Malfunction of valve seat?
Spark plug is loose?
Worn piston rings?
Re-seat valves.
Replace spark plug.
Replace piston rings.
Malfunction in air-cleaner
system, air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER —TROUBLESHOOTING (ENGINE)
TABLE 6. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Malfunction in cooling fan?
Air in-take filter clogged?
SOLUTION
Check or replace cooling fan.
Insufficient power output
"compression" and overheats
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Replace lubricating oil with correct viscosity.
Lubricating oil is wrong
viscosity?
Exhaust color is continiously
"WHITE"
Worn rings?
Replace rings
Air cleanner clogged?
Clean or replace air cleaner.
Adjust choke valve to the correct position.
Choke valve has not been set
to the correct position?
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
PAGE 28 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER —TROUBLESHOOTING (MIXER/MOTOR)
TABLE 7. MIXER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
Worn or defective V-belt?
No power?
SOLUTION
Replace V-belt.
Blades will not rotate.
Check electric or gasoline engine.
Replace seals.
Material leaking from drum
ends.
Worn or defective paddle shaft
seals?
Defective or worn drum support
brackets?
Apply grease to bracket or replace.
Drum difficult to discharge (tilt)
Blades adjusted too tight?
Adjust blades until they almost touch side walls of drum.
TABLE 8. ELECTRIC MOTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
No voltage to motor?
SOLUTION
Check power source.
Replace extension cord.
Replace switch.
Defective extension cord?
Defective motor ON/OFF switch?
Defective motor windings?
Worn or defective V-belt?
Blades will not rotate.
Repair windings or replace windings.
Replace V-belt.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER —WIRING DIAGRAM (ELECTRIC MOTOR)
Figure 23. Electric MotorWiring Diagram
PAGE 30 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Section 1: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Section 2: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial number
range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model number
or model number variant.
Section 3: Items Found In the“Items Number”Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
■
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
The contents of this parts catalog are
subject to change without notice.
NOTE
PAGE 32 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — SUGGESTED SPARE PARTS
MS15H/MS15E MIXER 1TO 3 UNITS
WITH HONDA GX160K1HX2 ENGINE
Qty.
P/N
Description
2 ............ 491010 ............ RUBBER LATCH ASSY.
1 ............ 508473 ............ V-BELT, ELECTRIC MOTOR A37
1 ............ 80000-008 ...... WIPER KIT
3 ............ 9807956846 .... SPARK PLUG HONDA 5.5HP
3 ............ 17210ZE1505 . ELEMENT, AIR HONDA 5.5 HP
1 ............ 28462ZH8003 . ROPE, RECOIL STARTER, HONDA 5.5 HP
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS.
PAGE 34 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS.
NO
PART NO
PART NAME
QTY.
REMARKS
1
*
2
*
3
*
5
*
6
*
7
8
*
9
*
504713
510165
512527
DCL160A
25259-001
DECAL:WARNING READ
1
3
1
2
1
DECAL: STOW (MULTIQUIP) SMALL
DECAL: STOW (MULTIQUIP) BIG
DECAL:WARNING ENGINE SHUTOFF
DECAL:WARNING GRATE
DECAL: NAMEPLATE ............................... 1 ............ CONTACT MQ PARTS DEPT.
DECAL: POWDER COATED
DECAL:PROP.65 WARNING
13118
DCL160
1
1
SEE DECAL ILLUSTRATIONS ON PAGE 13.
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — STEELTUB ASSY.
STEELTUB ASSY.
PAGE 36 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — STEELTUB ASSY
STEEL TUB ASSY.
NO
2
*
3
PART NO
26084-352
26085-351
23180-001
19728-001
19722-001
33177-001
33044-001
25492-001
33048-001
33084-001
33084-002
18937-001
07745-001
17985-008
17985-010
07029-006
07033-006
07030-008
07030-006
07028-055
06501-008
07594-012
19721-001
25648-501
26083-502
PART NAME
QTY.
1
1
1
2
2
2
2
1
1
2
2
1
4
8
6
15
14
2
4
2
1
2
2
REMARKS
DRUM
GRATE
HAND GRIP
TRUNNION
SHAFT SEAL
SEALED BEARING
SHAFT SEAL
DUMP LEVER
12
18
19+
*
*
*
20
21+
22
*
24
25
26
MAIN GEAR
*
BEARING HALF - UPPER
BEARING HALF - LOWER
LARGE WASHER
GREASE FITTING
CARRIAGE BOLT 3/8 - 16 X 1
CARRIAGE BOLT 3/8 - 16 X 1-1/4
LOCKWASHER 3/8
HEX NUT 3/8 - 16
FLATWASHER 1/2
FLATWASHER 3/8
COTTER PIN 5/32 X 1
HEX HEAD CAP SCREW 3/8 - 16 X 1
ROLL PIN 3/16 X 3/4
RETAINING RING
27
*
37
*
39
*
40
42
*
43
*
46
48
50
56
*
62
*
63
*
SHAFT SEAL KIT ....................................1 ..... INCLUDES ITEMS W/+
DRUM ASSY. W/SHAFT MAIN GEAR .....1 ..... INCLUDES ITEM W/ , ALSO INCLUDES
*
PADDLE SHAFT P/N 29062-351
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — PADDLE SHAFT ASSY.
PADDLE SHAFT ASSY.
PAGE 38 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — PADDLE SHAFT ASSY.
PADDLE SHAFT ASSY.
NO.
1
2
PART NO.
29062-351
492584
PART NAME
QTY.
1
6
REMARKS
PADDLE SHAFT
NUT, LOCK 1/2"
3
4
5
6
530181C
492400
EM200292
530180C
504322
PADDLE ARM, CENTER ENGINE END
SCREW, HHC 1/2"-13 X 3-1/2
INSERT, PADDLE ARM
PADDLE ARM, ENGINE END
WASHER, FLAT 1/2"
1
2
4
1
7
6
8
9
10
11
12
EM200297
530179C
505196
3019092
514725
514726
1456
0166A
530182C
530201
33017-001
80000-008
U-BOLT, END PADDLES
PADDLE ARM, CENTER TOW END
SCREW, HHC 5/16-18 X 1-3/4 G5
WASHER, FLAT 3/8"
BLADE, SIDE, RUBBER
BLADE, SIDE, SCRAPPER
NUT, HEX FINISH 3/8-16" NC G5
WASHER, LOCK 3.8"
2
1
12
12
4
*
13
4
14
15
16
17
18
19
12
12
1
2
2
PADDLE ARM, TOW END
BLADE ,SCRAPPER END
BLADE, RUBBER END
*
KIT, WIPERS............................................................... 1 ...................INCLUDES ITEMS W/
*
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — FRAME ASSY.
FRAME ASSY.
PAGE 40 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — FRAME ASSY.
FRAME ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
PART NAME
QTY.
4
1
1
6
6
1
2
4
2
2
4
4
4
4
2
REMARKS
EM98195
530467
530226
492381
EM969013
530168
530166
501299
491002
490957
492356
504451
2101402
492561
513699
GRIP, RUBBER BLACK
HANDLE, FRONT-LEFT
HANDLE, FRONT-RIGHT
SCREW, 3/8 NC 2-1/2 G5
NUT, NYLOCK
FRAME
HANDLE BACK
WASHER, FLAT
WHEEL , TIRE ASSY.
SNAP RING 5100-100
BOLT, 1/4" X 3/4"
WASHER, FLAT 1/4"
WASHER, LOCK 1/4"
NUT, HEX HEAD 1/4"-20
BUSHING
9
10
11
12
13
14
15
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — ENGINE COVER ASSY.
ENGINE COVER ASSY.
PAGE 42 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — ENGINE COVER ASSY.
ENGINE COVER ASSY.
NO
1
2
3
4
PART NO
07028-057
18604-005
26922-351
491010
PART NAME
QTY.
REMARKS
COTTER PIN 5/32 x 1/2
RETAINER CHAIN
ENGINE HOUSE ASSY.
LATCH ASSY.
2
1
1
1
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — HONDA ENGINE ASSY.
HONDA ENGINE ASSY.
PAGE 44 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — HONDA ENGINE ASSY.
HONDA ENGINE ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
GX160K1HX2
10057-016
18941-004
07030-005
07029-005
07033-005
06499-006
33054-001
06500-012
26921-001
PART NAME
QTY.
REMARKS
ENGINE-5.5 H.P. HONDA.................. 1 ............ REPLACES 22052-501
SQUARE KEY 3/16 x 1-1/2
SOCKET SET SCREW 1/4-20 x1/4
FLATWASHER 5/16
LOCKWASHER 5/16
HEX NUT 5/16 -18
CAP SCREW 1/4-20 x 3/4
PINION GEAR
CAP SCREW 5/16 - 18 x 1-1/2
GEAR GUARD
1
2
4
4
4
4
1
4
1
9
10
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
PAGE 46 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS15H/MS15E MIXER — ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
NO
20
21
30
32
33
34
49
51
71
82
84
92
93
94
95
100
101
106
PART NO
33060-001
17985-010
33054-001
07030-005
07029-005
07033-005
07029-004
07033-004
26044-001
22743-002
512518
19867-001
512466
10057-016
508473
18941-004
06500-008
07030-012
PART NAME
QTY.
2
4
1
4
4
4
6
6
1
1
1
1
1
3
1
4
REMARKS
PILLOW BLOCK
CARRIAGE BOLT 3/8-16 x 1-1/4
DRIVE PINION GEAR
FLAT WASHER 5/16
LOCK WASHER 5/16
HEX NUT 5/16-18
LOCKWASHER 1/4
NUT, HEX 1/4-20
BRACKET
MOTOR & CONTROL ASSY. 1.0 HP
DRIVE PULLEY
SHAFT
DRIVEN PULLEY
SQUARE KEY 3/16 x 1-1/2
V-BELT, A-37
SOCKET SET SCREW 1/4-20 x1/4
CAP SCREW 5/16-18 x 1
FLATWASHER 3/4
4
1
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
HONDA ENGINE — CYLINDER HEAD
PAGE 48 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
12210ZH8000
12204ZE1306
12205ZE1315
12216ZE5300
12251ZF1800
12310ZE1010
12391ZE1000
15721ZH8000
90016ZE1000
90043ZE1020
90047ZE1000
9430110160
957230806000
9807956846
9807956855
CYLINDER HEAD, COMP ......................... 1.......... INCLUDES ITEMS W/
*
2
*
3
*
4
5
6
7
8
9
10
11
12
14
15
GUIDE, IN. VALVE (OVER SIZE)
GUIDE, EX. VALVE (OS)
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE 6X13
BOLT, STUD 6X109
BOLT, STUD 8X32
PIN A, DOWEL 10X16
BOLT, FLANGE 8X60
1
1
1
1
1
1
1
4
2
2
2
4
1
1
PLUG, SPARK (BPR6ES NGK)
PLUG, SPARK (W20EPR-U ND)
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 50 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO
1
2
PART NO
PART NAME
QTY.
REMARKS
06165ZE1000
12000ZH8811
15510ZE1023
16510ZE1000
16511ZE1000
16513ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91202883005
91353671003
9405010000
GOVERNOR KIT .................................................. 1 ......... INCLUDES ITEMS W/
*
CYLINDER ASSY. BARREL OIL ALERT ............. 1 ......... INCLUDES ITEMS W%
SWITCH ASSY. OIL LEVEL
GOVERNOR ASSY. ............................................. 1 ......... INCLUDES ITEMS/W#
WEIGHT, GOVERNOR
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, THRUST 6MM
WASHER, DRAIN PLUG 10.2MM
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL(6205)
OIL SEAL 25x41x6
3
4
1
*
5 #
2
2
1
1
2
1
2
1
1
1
1
1
2
1
2
*
7 #
*
8
*
9
10
11
12
*
13
14%
15%
16
*
O-RING 14MM ARAI
NUT, FLANGE 10MM
WASHER, PLAIN, 6MM
PIN, LOCK, 8MM
BOLT, FLANGE 6 x 12
17
18
9410106800
9425108000
957010601200
*
19
20
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 52 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO
1
3
4
5
9#
10%
PART NO
PART NAME
QTY.
REMARKS
11300ZE1633
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
91202883005
9430108140
COVER ASSY, CRANKCASE (W TYPE)... 1 .........INCLUDES ITEMS W/
*
GASKET CASE COVER
CAP ASSY, OIL FILLER............................ 1 .........INCLUDES ITEMS W/#
CAP ASSY, OIL FILLER............................ 1 .........INCLUDES ITEMS W/%
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
OIL SEAL, 25X41X6
PIN A, DOWEL 8X14
BOLT, FLANGE 8X32
1
1
1
1
2
6
1
11
*
12
13
957010803200
961006205010
14
BEARING, RADIAL BALL, 6205
*
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 54 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
5
PART NO.
13310ZE1621
PART NAME
CRANKSHAFT (H-TYPE)
QTY.
1
REMARKS
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 56 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO
1
1
1
1
2
2
2
2
3
4
5
*
6
PART NO
PART NAME
QTY.
REMARKS
13010ZF1023
13011ZF1023
13012ZF1023
13013ZF1023
13101ZH8000
13102ZH8000
13103ZH8000
13104ZH8000
13111ZE1000
132A0ZE1000
90001ZE1000
90551ZE1000
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON (STD)
1
1
1
1
1
1
1
1
1
PISTON (0.25)
PISTON (0.50)
PISTON (0.75)
PIN, PISTON
ROD ASSY, CONNECTING ....................... 1 ......... INCLUDES ITEMS W/
BOLT, CONNECTING ROD
CLIP, PISTON PIN, 18MM
*
2
2
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 58 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO
1
2
3
4
PART NO
PART NAME
QTY.
REMARKS
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. ................................... 1 ......... INCLUDES ITEMS W/
*
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
VALVE, EX.
SPRING, VALVE
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR,VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT
2
2
2
2
1
1
1
2
1
1
1
1
2
2
5
6
*
7
8
9
10
11
12
13
14
15
NUT, PIVOT ADJUSTING
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 60 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
957010600800
STARTER ASSY, RECOIL NH1(BLACK) ... 1 ......... INCLUDES ITEMS W/
*
2
CASE COMP., RECOIL STARTER
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
12
*
BOLT, FLANGE 6X8
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 62 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO
2
4
7
8
10
11
14
PART NO
PART NAME
QTY.
REMARKS
19610ZE1000ZC
19612ZH8810
90601ZH7013
19630ZH8000
32197ZH8003
36100ZE1015
90022888010
COVER COMP., FAN NH1(BLACK)
PLATE, SIDE (STD)
CLIP, HARNESS
1
1
1
1
1
1
1
SHROUD COMP.
SUB-HARNESS
SWITCH ASSY., ENGINE
BOLT, FLANGE 6X20
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 64 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16955283000
162111ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1406
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
2
*
3
*
4
CHAMBER SET, FLOAT ......................... 1 ......... INCLUDES ITEMS W/%
SCREW SET
SCREW SET DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSY (BE65B) .............. 1 ......... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
GASKET, FULL STRAINER CUP
INSULATOR CARBURETOR
GASKET, INSULATOR
SPACER COMP. CARBURETOR
GASKET CARBURETOR
*
5
1
1
1
1
*
6 %
*
7
*
8
*
9
*
10
*
1
1
1
1
1
1
1
11
*
12
13
*
14
15
16
17
LEVER COMP., CHOKE (STD)............... 1 ......... INCLUDES ITEMS W/#
LEVER VALVE
18
1
1
1
1
1
2
1
1
1
1
1
*
19
*
PLATE LEVER SETTING
SPRING, PETCOCK LEVER
GASKET, PETCOCK
CUP, FUEL STRAINER
SCREW, PAN 3X6
PIN, SPRING 2X12
JET, MAIN #65
JET, MAIN #68
JET, MAIN #70
JET SET, PILOT #35
20
*
21
*
22
*
23
*
24#
25
99101ZH70650
99101ZH70680
99101ZH70700
99204ZE00350
*
25
*
25
*
26
*
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 66 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO
1
2
3#
4
PART NO
PART NAME
QTY.
REMARKS
16271ZE1000
17210ZE1505
17218ZE1821
17230ZE1820
17232891000
17238ZE7010
17239ZE1000
17410ZE1020
90201415000
90325044000
90325044000
957010602000
GASKET ELBOW
1
AIR CLEANER ELEMENT DUAL ............ 1 ......... INCLUDES ITEMS W/#
FILTER OUTER
COVER AIR CLEANER DUAL
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW COMP. AIR CLEANER .............. 1 ......... INCLUDES ITEMS W/
NUT CAP 6MM
NUT WING TOOL BOX SETTING
NUT WING TOOL BOX SETTING
BOLT FLANGE 6 x 20
1
1
1
1
1
5#
6
*
7
*
8
*
9
2
1
1
1
11
12
13
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 68 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO
1
3
7
8
11
12
15
PART NO
PART NAME
QTY.
REMARKS
18310ZH8810
18320ZF1H01
18355ZE1000
18381ZH8800
90050ZE1000
90055ZE1000
94001080000S
MUFFLER COMP.
1
1
1
1
4
1
2
PROTECTOR, MUFFLER
ARRESTER, SPARK
GASKET, MUFFLER
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
NUT, HEX (8MM)
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 70 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO
1
2
3
5
6#
11
12
13
14
15
PART NO
PART NAME
RUBBER, SUPPORTER
JOINT, FUEL TANK
TANK COMP., FUEL NH1 (BLACK)
CAP COMP., FUEL FILLER ...................... 1 ......... INCLUDES ITEMS W/#
GASKET, FUEL FILLER CAP
O-RING (14MM) ARAI
NUT, FLANGE (6MM)
BULK HOSE, FUEL (4.5X8000) (4.5X140) 1
CLIP, TUBE (B8)
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZF
17620ZH7013
17631ZH7003
91353671003
9405006000
1
1
1
1
1
2
950014500840M
9500202080
957010602500
2
1
BOLT, FLANGE (6X25)
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 72 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO
1
2
4
5
PART NO
PART NAME
KEY, SPECIAL WOOD RUFF, 25X18
FAN, COOLING
PULLEY STARTER
FLYWHEEL COMP.
NUT, SPECIAL, 14MM
QTY.
REMARKS
13331357000
19511ZE1000
28451ZH8003
31100ZE1000
90201878003
1
1
1
1
1
8
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 74 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO
1
2
7
11
PART NO
PART NAME
QTY. REMARKS
30500ZE1033
30700ZE1013
36101ZE1010
90121952000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE, 6X25
1
1
1
2
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 76 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO
2
4
5
6
PART NO
PART NAME
QTY.
REMARKS
16500ZH8821
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8000
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8811
16584883300
16592ZE1810
90013883000
90015ZE5010
90114SA0000
93500050250H
938930501600
9405006000
CONTROL ASSY., REMOTE ..................... 1 ......... INCLUDES ITEMS W/
*
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE COMP., CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE (6X12)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK (6MM)
SCREW, PAN (5X25)
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
7
8
9
*
*
10
*
11
12
13
14
15
17
18
19
22
23
24
*
*
*
*
*
*
*
*
SCREW WASHER (5X16)
NUT, FLANGE, 6MM
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
PAGE 78 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
21521883741
21591ZH8740
21621883741
21692ZH8800
23710883740
90002883740
90131883000
91202883005
9410912000
CASE, REDUCTION
1
1
1
1
1
1
1
1
1
1
1
1
1
GASKET, REDUCTION CASE
COVER, REDUCTION
GASKET, REDUCTION COVER
SHAFT, P.T.O.
BOLT, BREATHING
BOLT, DRAIN PLUG
OIL SEAL, 25 x 41 x 6
WASHER, DRAIN PLUG
BOLT, FLANGE 8 x 32
BOLT, FLANGE 8 x 35
BEARING, RADIAL BALL 6204
BEARING, RADIAL BALL 6305
9
10
11
12
13
957010803208
957010803500
961006204000
961006305000
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — LABEL ASSY.
LABEL ASSY.
PAGE 80 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1HX2 ENGINE — LABEL ASSY.
ENGINE LABELS ASSY.
NO.
1
3
6
7
8
15
PART NO.
PART NAME
QTY.
REMARKS
87521ZH8020
87522ZH9000
87528ZE1810
87530ZH8810
87532ZH8810
887586ZH7W00
ENBLEM 5.5
1
1
1
1
1
1
LABEL, CAUTION
MARK, CHOKE
LABEL, SPECIFICATION (EXTERNAL)
MARK, OIL ALERT (E)
LABEL, FUEL CAUTION
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 15, 2003
Terms and Conditions of Sale
STOW Construction Equipment
PAYMENT TERMS
DROP SHIPMENTS
The sender will be notified of any material
received that does not meet the above
provisions. Such material will be held for 30
days from notification pending instructions. If a
reply is not received within 30 days, the material
will be returned to the sender at his expense
with no credit issued.
Terms of payment for unit sales are 2% 15
days net 30 days from date of invoice unless
otherwise specifically stated on our invoice.
Parts invoices have terms of net 10 days.
Minimum parts billing is $15.00 net.
Applicable discounts will be computed on
merchandise value only. Late charges will be
assessed at prevailing rates. Cash discounts
cannot be taken on current billings if any
previously billed amounts are past due.
STOW reserves the right to refuse Drop
Shipments outside the normal service area of
the purchasing dealer.
FIELDWAREHOUSES
Field Warehouses are currently located in
California, Georgia, Idaho, Iowa, and New
Jersey
PRICING, REBATES AND
SPECIFICATIONS
Every effort will be made to provide adequate
notice of changes; however, prices and
equipment specifications are subject to change
without notice.
SPECIAL EXPEDITING SERVICE
The higher of a $35.00 surcharge or actual
costs will be added to the invoice for special
handling, including bus shipments, or in cases
where STOW personnel must personally deliver
the equipment or parts to the carrier.
FREIGHT POLICY
Freight policy is established to offer customers
every advantage possible. Due to bulk freight
ratings on some equipment and other shipping
considerations, freight policies differ by
equipment type. Actual back freight may be
charged for shipments originating from other
than specified FOB warehouses. See Freight
Policy for details.
All STOW domestic sales are FOB nearest
available designated MQ/STOW warehouse.
Export orders are ex-works factory located in
Carson, CA or Boise, ID.
Price changes are effective on a specific date
and all orders received on or after that date will
be billed at the revised price.
RETURNED GOODS POLICY
Return shipments may be accepted and credit
allowed, subject to the following provisions.
Rebates for price reductions and added
charges for price increases will not be made
for stock in dealer inventory at the time of a
price change.
1. A Returned Material Authorization (RMA)
must be approved by STOW prior to
shipment. Approvals for returned goods
must be with just cause and are at the
sole discretion of STOW. A copy of the
Authorization must accompany the shipment
to the designated Warehouse.
STOW reserves the right to quote and sell direct
to Government agencies and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
Additions to orders already shipped cannot be
accepted for freight minimums.
2. Parts being returned must be listed as
currently supplied on the current parts list.
LIMITATION OF SELLER’S LIABILITY
Should STOW elect to make partial shipments
of an order originally complying with the “freight
allowed” requirements, transportation charges
will be absorbed by STOW on any subsequent
shipment applying to that order.
STOW shall not be liable hereunder for damages
in excess of the purchase price of the item with
respect to which damages are claimed and in
no event shall STOW be liable for loss of profit
or good will or for any other special, consequential
or incidental damages.
3. Parts must be in new and resalable condition
in the original package, with part numbers
clearly marked.
4. Units and accessories must be current
models in the latest price list and in new and
resalable condition.
All other orders will be shipped collect or prepaid
with charges added to the invoice. STOW’s
responsibility ceases when a signed manifest
has been obtained from the carrier, and any
claim for shortage or damage must be settled
between the consignee and the carrier.
LIMITATION OF WARRANTIES
5. Special order items are not returnable for
credit.
There are no warranties, express or implied,
made by STOW. hereunder on Products
manufactured or distributed by it except the
warranty against defects in material and
6. Credit on returned parts and units will be
issued at actual dealer net price at time of
purchase less 15% restocking charge.
Parts: FOB Carson, California or Boise,
Idaho. See Freight Policy for details and
additional discounts.
7. All returned shipments are to be made to
the STOW designated receiving point,
freight prepaid at the sender’s expense.
STOW CONSTRUCTION EQUIPMENT
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-661-4242 • 877-BUY-STOW
FAX:310-604-9237
E-MAIL: [email protected]
Atlanta • Boise • Newark • Quebec, Canada
Manchester, UK • Rio de Janeiro, BR • Puebla, MX
PAGE 82 — MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV.FINAL (08/10/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
STOW MAIN OFFICE
Post Office Box 6254
Carson, Ca 90749
888-252-STOW
FAX:310-537-1986
Email: [email protected]
PARTS DEPARTMENT
800-427-1244
FAX:800-672-7877
FAX:310-637-3284
^^^^^^^*^6668
310-537-3700
SERVICE DEPARTMENT
800-421-1244
FAX:310-537-4259
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
FAX:310-631-5032
FAX:310-537-1173
WARRANTYDEPARTMENT
800-421-1244, EXT.279
310-537-3700, EXT.279
SALES DEPARTMENT
310-661-4242
FAX:310-604-9237
877-289-7869(877-BUY-STOW)
Your Local Dealer is:
STOW CONSTRUCTION EQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
888-252-STOW [888-252-7869]
FAX:310-537-1986
Download from Www.Somanuals.com. All Manuals Search And Download.
|