COMMERCIAL / RESIDENTIAL GAS WATER HEATERS
SERVICE HANDBOOK
ULTRA HIGH EFFICIENCY
POWER VENT / POWER DIRECT VENT
FOR MODELS:
• SHE50-100 NE
• SHE50-100 PE
• GP650 YTPDT
• GP650 HTPDT
PRINTED 0308
198148-000
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
INTRODUCTION
This Service Manual is designed to be an aid in servicing and troubleshooting the 96%
thermally efficient, 50 gallon, 100,000 Btu/hr residential and light duty commercial power
vent - power direct vent model water heaters listed on the cover of this manual.The
instructions, illustrations and procedures contained in this manual are used to verify proper
operation and to diagnose and repair common service problems.
This manual does not replace or supersede the Instruction Manual that came with the water
heater. Always refer to the Instruction Manual that came with the water heater for complete
installation instructions. If the Instruction Manual is not available copies can be obtained
from the manufacturers web site or by calling the technical support phone number shown on
the water heater labeling.
QUALIFICATIONS - QUALIFIED SERVICE AGENT
Servicing the products referenced in this manual requires the ability (in the field involved)
equivalent to that of a Qualified Service Agent as defined by the American National
Standards Institute (ANSI) below. Installation skills such as plumbing, air supply, venting,
gas supply, electrical supply are required in addition to diagnostic and electrical testing
skills.
ANSI Z223.1 2006 Sec. 3.3.83: “Qualified Agency” - “Any individual, firm, corporation or
company that either in person or through a representative is engaged in and is responsible
for (a) the installation, testing or replacement of gas piping or (b) the connection, installation,
testing, repair or servicing of appliances and equipment; that is experienced in such work;
that is familiar with all precautions required; and that has complied with all the requirements
of the authority having jurisdiction.”
SERVICE WARNING
If you are not qualified (as defined by ANSI above) and licensed or certified as required by
the authority having jurisdiction to perform a given task do not attempt to perform any of the
service or installation procedures described in this manual. If you do not understand the
instructions given in this manual or do not feel confident in your abilities to perform a given
task do not attempt to perform any procedures outlined in this manual.
IMPORTANT SERVICE REMINDER
When performing any troubleshooting step outlined in this Service Manual always consider
the wiring and connectors between components. Perform a close visual inspection of all
wiring and connectors to and from a given component before replacement. Ensure wires
were stripped before being crimped in a wire connector, ensure wires are crimped tightly in
their connectors, ensure connection pins in sockets and plugs are not damaged or worn,
ensure plugs and sockets are mating properly and providing good contact.
Failure to perform this critical step or failing to perform this step thoroughly often results in
needless down time, unnecessary parts replacement, and customer dissatisfaction.
Technical Literature Department
2 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
INSTRUCTION MANUAL
Have a copy of the Instruction Manual that came with the water heater on hand for the
correct model water heater you are working with before servicing.
Installation information given in this Service Manual is not a complete installation
instruction. Installation information covered in this Service Manual has a limited focus as it
applies to servicing. This Service Manual does not replace or supersede the Instruction
Manual that came with the water heater. Always refer to the Instruction Manual that came
with the water heater for complete installation instructions.
If the Instruction Manual is not on hand copies can be obtained from the manufacturers web
site or by calling the technical support phone number shown on the water heater labeling.
TOOLS REQUIRED
• Instruction Manual that came with the water heater.
• All tools common to installation and service of commercial water heaters such as hand
tools, torch, pipe wrenches etc.
• Long (8-10”) T handle SAE hex (allen key) wrenches including 5/32”, 1/8” and 1/4” - for
blower, burner, and gas valve removal and installation.
• Two digital manometers range -20.00 to +20.00" W.C., resolution - 0.01" W.C.
Recommend UEI model EM200 or equivalent. Required to test performance of air
pressure switches. Also used to measure low pressure supply gas and manifold gas
pressure.
• Digital Multi Meter DMM; recommend Fieldpiece HS36, Fluke 187, UEI DL289 or
equivalent capable of measuring:
• AC/DC Voltage
• AC Frequency (Hz)
• Ohms
• DC micro amps µA (flame sensing current)
• AC amp meter- recommend UEI model DL289 or equivalent.
Technical Literature Department
3 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
INSTALLATION CONSIDERATIONS
INSTRUCTION MANUAL
Installation information given in this Service Manual is not a complete installation
instruction. Installation information covered in this Service Manual has a limited focus as it
applies to servicing. This Service Manual does not replace or supersede the Instruction
Manual that came with the water heater. Always refer to the Instruction Manual that came
with the water heater for complete installation instructions.
If the instruction Manual that came with the water heater is not on hand copies can be
obtained from the manufacturers web site or by calling the technical support phone number
shown on the water heater labeling.
CLOSED WATER SYSTEMS
Water supply systems may, because of code requirements or such conditions as high line
pressure, among others, have installed devices such as pressure reducing valves, check
valves, and back flow preventers. Devices such as these cause the water system to be a
closed system.
Virtually all commercial and most residential water supply systems are closed systems
today. Closed water systems will experience thermal expansion which, if not controlled with
a properly installed and sized thermal expansion tank, can cause premature failure
(leakage) of the water heater. Water heater failure (leakage) on closed systems where there
is not a thermal expansion tank installed is not covered under the limited warranty.
THERMAL EXPANSION
As water is heated, it expands (thermal expansion). In a closed system the volume of water
will grow when it is heated. As the volume of water grows there will be a corresponding
increase in water pressure due to thermal expansion. Thermal expansion can cause
premature tank failure (leakage). This type of failure is not covered under the limited
warranty. Thermal expansion can also cause intermittent temperature-pressure relief valve
operation: water discharged from the valve due to excessive pressure build up. This
condition is not covered under the limited warranty. The temperature-pressure relief
valve is not intended for the constant relief of thermal expansion.
A properly sized thermal expansion tank should be installed on all closed systems to control
the harmful effects of thermal expansion.
Technical Literature Department
4 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR REQUIREMENTS
Carefully review the requirements for combustion and ventilation air in the Instruction
Manual that came with the water heater. Failure to meet these requirements when the water
heater is installed or overlooking their importance when servicing the water heater often
results in needless down time, unnecessary parts replacement, and customer
dissatisfaction. If the Instruction Manual is not on hand copies can be obtained from the
manufacturers web site or by calling the technical support phone number shown on the
water heater labeling.
An inadequate supply of air for combustion and ventilation often causes operational
problems. A lack of combustion and ventilation air can create a negative ambient air
pressure in the installed space which can lead to improper combustion and operational
problems with air pressure switches.
CONTAMINATED AIR
Combustion air that is contaminated can greatly diminish the life span of the water heater
and water heater components such as hot surface igniters and burners. Propellants of
aerosol sprays, beauty shop supplies, water softener chemicals and chemicals used in dry
cleaning processes that are present in the combustion, ventilation or ambient air can cause
such damage.
Vapors from volatile compounds such as solvents, cleaners, chlorine based chemicals and
refrigerants in addition to being highly flammable in many cases, can also react to form
highly corrosive substances such as hydrochloric acid inside the water heater’s combustion
chamber. The results can be hazardous and cause product failure.
If this water heater will be installed in beauty shops, barber shops or laundries with dry
cleaning equipment, it is imperative the water heater be installed as a Direct Vent appliance
so that air for combustion is derived directly from the outside atmosphere through a sealed
intake air pipe. See the Installation of Vent System section in the Instruction Manual that
came with the water heater for more information on Direct Vent installations.
Technical Literature Department
5 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
VENTING
The venting information presented in this Service Manual is not a complete venting
installation instruction. Refer to the Instruction Manual that came with the water heater for
complete installation instructions.
The water heater covered in this Service Manual may be installed as a conventionally
vented water heater or as a direct vent water heater. Conventional vent installations use
room air for combustion. There will be one “vent” pipe installed on a conventional vent
installation. Direct vent installations derive all air for combustion from the outdoor
atmosphere through a second “intake air” pipe. There will be two pipes (vent and intake air)
installed on a direct vent installation.
The vent and intake air piping (direct vent installations) may not be combined with any other
appliances under any conditions.
Maximum Equivalent Length Requirements
The vent and intake air pipe (direct vent installations) for the water heater covered in this
Service Manual can be installed using 2, 3, or 4 inch pipe depending on the overall
The vent and intake air terminations do not factor into the overall equivalent feet
calculations.
The vent and intake air connection fittings on the water heater do not factor into the overall
equivalent feet calculations.
Additional 2 or 3 inch 90° elbows installed are equivalent to 5 linear feet of pipe. Additional 4
inch 90° elbows are equivalent to 8 linear feet of pipe. 45° elbows will count for half the
equivalent length a 90° elbow does.
= 5 linear feet of pipe
2”
= 5 linear feet of pipe
3”
= 8 linear feet of pipe
4”
Overall equivalent lengths are determined by adding the total length of pipe installed to the
accumulated total equivalent length of all the additional elbows factored in.
The maximum equivalent lengths given in the Instruction Manual that came with the water
2 inch vent pipe can be up to 20 equivalent feet with one 90° elbow. On a direct vent
installation the 2 inch intake air pipe can also be up to 20 equivalent feet with one 90° elbow.
Carefully review the venting installation instructions and maximum equivalent length
requirements for the vent and intake air piping. Ensure the vent system has been installed
per Instruction Manual requirements.
Technical Literature Department
6 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
VENTING (CONT)
Pipe Size Requirements
Ensure the correct size pipe has been used for the overall equivalent length of the vent and
intake air piping installed. Longer equivalent lengths require larger pipe sizes, see Table 1.
Maximum Elbow Requirements
Three and four inch vent and intake air pipe installations allow a maximum of 6 - 90° elbows
in the vent pipe AND a maximum 6 - 90°elbows in the intake air pipe. Two inch installations
allow a maximum of 3 - 90° elbows in the vent pipe AND a maximum 3 - 90° elbows the
intake air pipe.
Table 1
NUMBER
2” MAXIMUM PIPE
3” MAXIMUM PIPE
4” MAXIMUM PIPE
90° ELBOWS
LENGTH FEET (METERS) LENGTH FEET (METERS) LENGTH FEET (METERS)
1
2
3
20 (6.1)
15 (4.6)
10 (3.0)
60 (18.3)
55 (16.8)
50 (15.2)
120 (36.6)
112 (34.1)
104 (31.7)
4 elbows not allowed in 2” pipe
(use larger pipe size)
4
5
6
45 (13.7)
40 (12.2)
35 (10.7)
96 (29.3)
88 (26.8)
80 (24.3)
5 elbows not allowed in 2” pipe
(use larger pipe size)
6 elbows not allowed in 2” pipe
(use larger pipe size)
Service Notes - Venting
Remove all plastic debris from the edges of intake air pipe sections after cutting on direct
vent installations. Plastic debris left on intake air pipe sections can collect inside and clog the
Using a smaller pipe size than required for a given length or installing more elbows on the
vent pipe can cause the water heater’s control system to declare a fault condition, lock out
Overlooking the same requirements for the intake air pipe on direct vent installations or
failing to remove the screen from the intake air connection when direct venting can cause
the water heater’s control system to declare a fault condition, lock out and display the
The screen inside the intake air connection is meant to keep
larger debris from entering the blower when the water heater is
installed conventionally; using room air for combustion.
Remove This Screen
For Direct Vent
Installations
When the water heater is installed in a direct vent configuration
the screen inside the intake air connection on the water heater
must be removed. If left in place it will become clogged over time
and lead to “Blocked Inlet” lock out conditions.
The screen on the intake air termination will keep larger debris
from entering the blower on direct vent installations.
Technical Literature Department
7 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
ELECTRICAL REQUIREMENTS
The water heater covered by this Service Manual must be grounded in accordance with
the local codes, or in the absence of local codes: the National Electrical Code (NFPA 70) or
the Canadian Electrical Code (C22.1).
The water heater covered by this Service Manual requires a 120 VAC 1Ø (single phase)
power supply. It is factory equipped with a standard 3 prong appliance cord that plugs into a
standard 120 VAC wall outlet. 5.2 FLA (full load amps) approximate.
As shown in the illustration below there should be 120 VAC present between the power
supply hot and ground wires. 120 VAC should also present between the hot and neutral
wires. There should be 0 VAC present between the neutral and ground wires.
Correct wiring for a standard 120 VAC wall outlet is also shown in the Illustration below. Note
the orientation of the ground connect is at the bottom. Reversed polarity is when the hot and
neutral wires are connected opposite from what is shown here.
Service Notes - Electrical
This water heater is a polarity sensitive appliance and will not operate if the power supply
polarity is reversed. If the polarity of the power supply is reversed the water heater’s control
system will declare a fault condition and display “AC Reversed” on the UIM display.
The water heater’s burner must be grounded for flame sensing current to be established and
verify ignition. If the burner is not grounded the water heater’s control system will declare a
fault condition and display “Ignition Failure” on the UIM display after 3 failed ignition trials.
Also shown is an outlet tester that will quickly determine if the plug is wired correctly. These
testers will also diagnose reversed polarity, open ground and open neutral wire problems.
Outlet testers are inexpensive and simple to use. They are available at most hardware
stores and home centers.
120 VAC 1Ø Power Supply
Correctly Wired Outlet
120 VAC 1Ø
Wall Outlet
HOT
NEUTRAL
GROUND
Neutral
Hot
Ground
Outlet Tester
120 volts
0 volts
120 volts
Technical Literature Department
8 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
OPERATION & SERVICE
HOW IT WORKS
This section of the Service Manual will cover operation, common service procedures and
water heater construction. The water heater covered in this Service Manual has a helical coil
shaped heat exchanger that is submerged in the storage tank. The water heater uses a top
mounted down fired radial burner. This is a forced draft burner; hot burning gases are forced
through the heat exchanger under pressure and exit through the exhaust/vent connection
located at the bottom of the water heater.
INTERNAL VIEW
COMBUSTION
BLOWER/BURNER
AIR INTAKE
GAS VALVE
ASSEMBLY
CONNECTION
Starting at the top combustion air and
fuel gas are drawn in by the blower
The hot burning gases exit the radial
through the coil shaped heat
exchanger.
Flue gases spiral through the heat
exchanger and exit the water heater
through the exhaust/vent connection
at the bottom.
EXTERNAL VIEW
COMBUSTION
AIR INTAKE
HELICAL
SHAPED
HEAT EXHNGER
CONNECTION
EXHAUST/VENT
CONNECTION
EXHAUST/VENT
CONNECTION
Technical Literature Department
9 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
BLOWER
The blower is an assembly consisting of the blower housing, motor and an integrated VFD
(variable frequency drive). Blower operation is controlled by the CCB (central control
socket. The CCB also sends a PWM (pulse width modulation) signal to the Blower/VFD
assembly low voltage 5 pin socket.
The PWM signal is a digital instruction sent to the VFD instructing it to start, stop, and control
blower speed. The VFD powers the blower motor directly. The VFD also varies the
frequency (Hz) of the power it sends to the blower motor which in turn controls blower
speed. Higher frequency = faster blower speed, lower frequency = slower blower speed.
Service Notes - Blower
The PWM signal plug MUST remain plugged in to the 5 pin socket on the blower assembly
at all times. Removing this plug will cause the blower to accelerate and the Btu/hr input of
the water heater to increase to a much higher rate. This may cause damage to the water
heater.
Blower Housing
Low Voltage PWM 5 Pin Socket
Blower Motor / VFD Assembly
High Voltage 120 VAC 3 Pin Socket
Technical Literature Department
10 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
BURNER
The images below show a complete blower/burner assembly removed along with a top view
of the water heater with the blower removed.
Service Notes - Burner (Flame Sensor)
The burner installed in the water heater is a radial fire burner. Radial fire burners can trap
debris that enter the blower. Be sure to thoroughly clean the edges of intake air pipe
sections after cutting during the installation. If this is not done plastic shavings can collect
inside the burner and lead to rough operation and/or ignition failure.
The burner should be removed and inspected whenever servicing for rough operation or
ignition failure problems. Burner removal requires removal of the blower. Blower removal
requires 8-10” long T handle 1/8” hex (allen) wrench.
The flame sensor will accumulate corrosion (rust etc) over time. This will reduce flame
sensing current. This is the most common cause of “Ignition Failure” lock outs. The flame
sensor should cleaned when servicing due to ignition failure and as a routine maintenance
procedure. Fine grade steel wool is recommended for cleaning the flame sensor; do not use
coarse abrasives such as sand paper.
Blower Adapter
Igniter
Radial Fire Burner
Blower VFD
Assembly
Flame Sensor
Top View Water Heater - Blower Removed
Burner Ground Wire
Blower Adapter
Burner View Port
Blower removal
requires 8 -10” long T
handle 1/8” hex (allen)
wrench.
Burner must be grounded
for flame sensing current to
be established. See Service
Technical Literature Department
11 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
BURNER (CONT)
Burner & Blower Removal
The burner should be removed and inspected whenever service is being performed for
rough operation or ignition failure. Radial fire burners like the one used on this water heater
can trap debris, see Service Notes - Venting on page 7.
The following images illustrate the burner removal procedure. Long T handle hex wrenches
(8-10”) will save considerable time when removing/installing the burner & blower.
BLOWER/BURNER REMOVAL PROCEDURE
Blower Prover Sensing Tube
1 Ensure power to the water heater is turned off.
2 The blower assembly must be removed first.
3 Disconnect the two wiring plugs from the blower
assembly sockets (see Service Notes - Blower
4 Disconnect the Blower Prover air pressure switch
sensing tube.
5 Remove 4 blower flange mounting screws -
1/8” hex. Using long T handle hex wrench will
save considerable time.Do not over tighten when
Blower Flange
1/8” Hex Machine Screws
reinstalling - torque should not exceed 40 inch
lbs.
6 Remove the blower assembly from the blower
adapter.
7 Remove the blower flange gasket. Gasket may be
reused if not damaged or showing signs of
excessive wear.
8 Remove the flame sensor - 1 Phillips head screw.
CONTINUED ON NEXT PAGE
Blower Flange
Flame Sensor
Blower Flange Gasket
Blower Adapter
Technical Literature Department
12 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
BURNER (CONT)
Burner/Blower Removal (cont)
BLOWER/BURNER REMOVAL PROCEDURE
(CONT)
9 Remove 4 blower adapter 1/4” hex machine
screws. Do not over tighten when reinstalling -
torque should not exceed 40 inch lbs.
1/4” Hex Machine Screws
10 Remove the blower adapter.
11 Be extremely careful when handling the Sight
can easily be dropped and lost - and the water
heater must have the sight glass in place to
operate safely.
12 Remove the hot surface igniter - 2 Phillips head
screws.
13 Remove the blower adapter gasket. Gasket may
be reused if not damaged or showing signs of
excessive wear.
Blower Adapter
14 Lift the burner up and out.
Blower Adapter Gasket
Sight Glass inside
Burner View Port
Burner
Hot Surface Igniter
Service Notes - Blower Flange & Blower Adapter Gaskets.
Whenever the blower or burner is removed for service DO NOT overtighten the machine
the water heater tank (above). Torque on these screws should not exceed 40 inch lbs.
If these mounting screws are overtightened the gaskets will be squeezed and deformed
from their natural shape. This can partially block the flow of the fuel air mixture and cause
rough starting, rough operation and ignition failure.
If these gaskets are deformed from overtightening the mounting screws it can also lead to
gasket leakage. Hot flue gases leaking from these points can burn up wiring, igniters, and
other components.
Technical Literature Department
13 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
VENTURI
A Venturi is connected to the inlet of the blower. All combustion air flows through the Venturi.
The outlet of the 24 VAC gas valve connects directly to the side of the Venturi. Fuel gas
flows from the outlet of the gas valve into the side of the Venturi directly.
Inside the Venturi there is a cone shaped restrictor that constricts the air passage to the
blower inlet. As air enters the constriction point it’s velocity increases. A pressure drop
occurs at this point and creates a negative pressure in the cavity between the cone shaped
restrictor and the Venturi housing. This negative pressure “pulls” gas from the outlet of the
gas valve into the blower where it is mixed with combustion air and then supplied to the
burner. See the images below.
24 VAC Gas Valve
Blower
Gas Inlet
Venturi Inlet
Venturi
Negative Pressure
Blower
Velocity Increases
At Constriction Point
Pressure Drops
Combustion Air
Negative Pressure
Burner
Supply Gas
Technical Literature Department
14 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
GAS VALVE
The outlet of the gas valve is connected by flange directly to the side of the Venturi (page
14). There is no manifold gas line on the water heater. A gas orifice with gasket is fitted into
the gas valve’s outlet flange. See the images below.
Gas Valve Removal
The gas valve must be removed to inspect the gas orifice. There are 3 - 5/32” hex head
screws that secure the gas valve to the Venturi. Long T handle hex wrenches (8-10”) will
save considerable time when removing/installing the gas valve, blower and burner.
GAS VALVE REMOVAL PROCEDURE
5/32” hex wrench
24 VAC Gas Valve
1 Ensure power to the water heater is turned off.
2 Turn off the supply gas shut off valve.
3 Disconnect supply gas line to water heater.
4 Remove 3 gas valve mounting screws - 5/32” hex
head machine screws. Support gas valve body
when removing last screw. Long T handle hex
wrenches (8-10”) will save considerable time
when removing/installing the gas valve.
5 Carefully lift gas valve body off of flange
connection on Venturi.
Venturi
6 Gas orifice and gasket are now accessible.
Gas Orifice
& Gasket
24 VAC Gas Valve
Venturi
Natural Gas Orifice
Propane Gas Orifice 0.162”
0.191”
Gas Orifice
& Gasket
Gasket
Orifice
Technical Literature Department
15 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
GAS PRESSURE TESTING
The water heater covered in this Service Manual is rated at 100,000 Btu/hr input. It is
certified for elevations up to 10,100 feet (3079 meters) without adjustment. Call the technical
support phone number shown on the water heater labeling before operating the water
heater at higher elevations.
Service Notes - Checking Gas Pressures
Manifold and supply gas pressure can be measured at two test ports on the water heater’s
gas valve. The manifold test port is closest to the blower housing and the supply test port is
furthest. The valve in each test port is opened/closed with a small slotted screwdriver.
Manifold gas pressure will run at 0.00” W.C. or lower, in a negative pressure, depending on
the operating state or mode the control system is currently in (see Venturi on page 14).
Manifold gas pressure will be considerably lower, -6.50” to -7.50” W.C. during the pre/post
purge modes when the blower is running and the gas valve is closed. When the gas valve
opens (energized) gas entering the Venturi will cause a rise in manifold gas pressure.
Manifold gas pressure will vary depending on vent/intake air pipe lengths. Manifold gas
pressure will typically be 0.00” W.C. to +0.05” W.C. during the heating mode.
There may also be a drop in supply gas pressure noticed when the water heater’s gas valve
opens. Seeing a rise in manifold pressure and a corresponding drop in supply gas pressure
confirms the gas valve is opening and gas is flowing to the burner. The procedure for
checking manifold and supply gas pressures is shown in the illustrations that follow.
CHECKING GAS PRESSURES
1 Ensure power to the water heater is turned off.
2 Turn off the supply gas shut off valve.
3 Open the manifold and supply gas pressure test
ports on the gas valve. Turn the needle valve
slotted heads 1/2 to 1 full turn counterclockwise
with a small slotted screwdriver.
4 Attach sensing tube from 2 digital manometers
Manifold Gas
Test Port
Supply Gas
Test Port
pressure test port on the gas valve as shown.
CONTINUED ON NEXT PAGE
Sensing Tubes
From Manometers
Turn test port needle valves counter-clockwise
to open and clockwise to close. Always close
test ports when finished and check for leaks
Supply Gas
Test Port
Manifold Gas
Test Port
Technical Literature Department
16 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
GAS PRESSURES (CONT)
CHECKING GAS PRESSURES (CONT)
5 Open the supply gas shut off valve - restore
power - start a heating cycle.
Typical manifold and supply gas pressures during:
1 Standby Mode
2 Pre-Purge Mode
3 Heating Mode
6 The rise in manifold pressure and corresponding
drop in supply gas pressure confirms the water
heater’s gas valve is opening and gas is flowing
to the burner.
7 Record the supply and manifold gas pressures
with the water heater firing.
1 BLOWER OFF / GAS VALVE OFF
Manifold 0.00” W.C. Supply +9.70” W.C.
8 Supply gas pressure should not drop below
minimum given in Table 2 below.
9 Manifold gas pressure should be within the range
shown in Table 2 below.
burner flame should be blue.
11 Shut off power and gas supply - disconnect
manometers - close test port needle valves.
Manifold
Gas
Supply
Gas
12 Restore power and gas supply. Check for gas
2 BLOWER ON / GAS VALVE OFF
3 BLOWER ON / GAS VALVE ON
Manifold -6.86” W.C. Supply +9.70” W.C.
Manifold +0.05” W.C. Supply +7.04” W.C.
Manifold
Gas
Supply
Gas
Manifold
Gas
Supply
Gas
Service Notes - Gas Pressure Adjustment
Manifold gas pressure is factory set and should not be adjusted in the field. If manifold gas
pressure differs greatly from the pressures in Table 2 consider the calibration of the
manometer being used - try a different manometer. Call the technical support phone number
on the water heater label for further assistance if pressures are considerably different.
Table 2 - Gas Pressures
†MINIMUM SUPPLY
FUEL TYPE
MAXIMUM SUPPLY
MANIFOLD
0.00” to +0.05” W.C.
(0.00 to +0.012 kPa)
Natural Gas
3.5” W.C. (0.87 kPa)
14.0” W.C. (3.48 kPa)
0.00” to +0.05” W.C.
(0.00 to +0.012 kPa)
Propane Gas
8.0” W.C. (1.99 kPa)
14.0” W.C. (3.48 kPa)
†. Minimum supply gas pressures must be maintained under both load and no load conditions.
Technical Literature Department
17 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR PRESSURE SWITCHES
Air pressure switch technical bulletins TB-A023-06 and TB-S023-06 explain air pressure
switch construction and test procedures in detail. These technical bulletins are available on
the manufacturers web site or by calling the technical support phone number shown on the
water heater labeling. Construction and types of air pressure switches used on the water
heater covered in this Service Manual are shown below.
Construction
Normal State
Activated State
(open switch contacts)
(closed switch contacts)
Switch Contacts
Wiring Terminals
Internal Linkage
Vent Port
Flexible Diaphragm
Sensing Port
Application & Type
Normal State
Activated State
Blower Prover
Air Pressure Switch
Normally open contacts,
close on a rise in pressure.
Blocked Intake
Air Pressure Switch
Normally closed contacts,
open on a fall in pressure.
Blocked Exhaust
Air Pressure Switch
Normally closed contacts,
open on a rise in pressure.
Technical Literature Department
18 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR PRESSURE SWITCHES (CONT)
The water heater covered in this Service Manual is factory equipped with three air pressure
switches. These switches are used to provide verification or prove electrically that the
blower is running and that the vent and intake air pipes are not blocked or restricted. The
switches are located on the top of the water heater as shown in the illustration below.
TOP VIEW
FRONT
• BLOWER PROVER SWITCH
normally open contacts - close on a rise in pressure
• BLOCKED INTAKE SWITCH
normally closed contacts - open on a fall in pressure
• BLOCKED EXHAUST SWITCH
normally closed contacts - open on a rise in pressure
All switches have SPST(single pole single throw) contacts.
These switches monitor air pressure through plastic sensing tubes from three different
sensing ports on the water heater. The Blower Prover switch monitors pressure from the
blower’s outlet flange. The Blocked Intake switch monitors pressure from the blower’s intake
air connection fitting. The Blocked Exhaust switch monitors pressure from the exhaust/vent
connection elbow on the bottom of the water heater. See the images below.
Blower Prover Switch
Blocked Intake Switch
Blocked Exhaust Switch
Blocked Exhaust Switch Sensing Port
Technical Literature Department
19 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR PRESSURE SWITCH OPERATION
The control system monitors the “state” of the air pressure switches individually through
whether the switch contacts are open or closed. See the construction drawings on page 18.
Before each call for heat begins, before the blower starts, the control system performs a
diagnostic test. During this test the control system checks the air pressure switches. The
switches must be in their correct normal state at this point.
The Blower Prover is a normally open switch and the Blocked Intake/Exhaust switches are
normally closed. If the Blower Prover is not verified open or the Blocked Intake/Exhaust
switches are not verified closed during this test; the control system would lock out and
display a fault message indicating which pressure switch had caused the fault condition. IE:
“Blower Prover Failure.”
After the blower starts the Blower Prover switch contacts must activate (close) for the
switch contacts do not close after the blower starts, the control system would lock out and
display a fault message; IE: “Blower Prover Open.”
Normal State
Activated State
(contacts closed - after blower starts)
Blower Prover
Air Pressure Switch
(contacts open - before blower starts)
Normally open contacts,
close on a rise in pressure.
The Blocked Intake and Blocked Exhaust switches must remain closed at all times. If the
control system senses the contacts of either of these switches are open it will lock out and
display a fault message; IE “Blocked Inlet” or “Blocked Exhaust Vent”
Technical Literature Department
20 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR PRESSURE SWITCH TESTING
Air pressure switch testing involves three procedures:
• Normal State Test
• Operational State Test
• Pressure Test
Normal State Test
Turn off power and disconnect the wires to the pressure switches. Wrap electrical tape
around the wire ends to prevent shorts. A continuity test is performed, using an ohm meter,
between the wiring terminals of the switch. The Blower Prover switch has normally open
contacts. The Blocked Intake and Blocked Exhaust switches have normally closed contacts.
If this test confirms the Blower Prover switch contacts are open and the Blocked Intake/
Exhaust switch contacts are closed - the switches have passed the test. If test results
indicate the Blower Prover switch contacts are closed - the switch must be replaced. If either
the Blocked Intake or Exhaust switch contacts are open - the switch must be replaced.
Operational State Test
The operational test is also a continuity test performed with an ohm meter between the
pressure switch wiring terminals. However, this test is performed while the blower is running
during the pre-purge mode. Ensure the wires to the air pressure switches are disconnected
and that electrical tape is wrapped around the wire ends to prevent shorts. Perform a
continuity test between the wiring terminals on the air pressure switches with the blower
running (water heater in pre-purge mode).
During this test the normally open contacts of the Blower Prover switch should close. The
Blower Prover switch “activates” (closes its contacts) during normal operation to verify or
“prove” that the blower is running. If the contacts remain open during this test the third test,
the pressure test, must be performed to determine if the pressure switch is defective. During
this test the Blocked Intake and the Blocked Exhaust switch contacts should remain closed,
if the contacts open during this test the third test, the pressure test, must be performed to
determine if the pressure switch is defective.
Technical Literature Department
21 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR PRESSURE SWITCH TESTING (CONT)
Pressure Test
The Pressure Test is necessary when the air pressure switch in question has passed the
Before performing this test examine the sensing tube connections on the water heater’s
kind of debris or condensate in the sensing tubes, repair/replace as necessary.
To determine if an air pressure switch is operating properly you must know the “pressure
activation” point for the switch and whether it activates on a rise or a fall in pressure. This
information is provided in Table 3 below.
Procedure: Disconnect the pressure sensing tube from the sensing port on the switch being
tested, leave the other end connected. Connect a digital manometer to the sensing tube.
Turn the power on and start a call for heat. When the blower comes up to full speed, record
the pressure reading. Repeat this at all three air pressure switches as necessary. Compare
Blower Prover Switch: If the pressure reading taken at the Blower Prover switch sensing
tube is at or above the activation pressure shown in Table 3 and the switch contacts did not
close in the Operational Test - the switch is defective and must be replaced. If the pressure
reading taken does not reach or rise above the activation pressure in Table 3 the pressure
switch IS NOT defective and should not be replaced - call the technical support phone
number shown on the water heater labeling for assistance.
Blocked Intake Switch: Note these are negative pressures. If the pressure reading taken at
the Blocked Intake switch sensing tube does not reach or drop lower than the pressure
shown in Table 3 and the switch contacts were opening during the Operational Test - the
switch is defective and must be replaced. If the pressure reading taken reaches or drops
lower than the pressure shown in Table 3 and the switch contacts were opening during the
Operational Test - the switch IS NOT defective and should not be replaced. Check for
restrictions, too many equivalent feet, or too many elbows in the intake air piping.
Blocked Exhaust Switch: If the pressure reading taken at the Blocked Exhaust switch
sensing tube does not reach or rise above the activation pressure given in Table 3 and the
switch contacts were opening during the Operational Test - the switch is defective and must
be replaced. If the pressure reading taken reaches or exceeds the pressure shown in Table
3 and the switch contacts were opening during the Operational Test - the switch IS NOT
defective and should not be replaced. Ensure the condensate tube connected to the exhaust
elbow on the water heater is not clogged and is draining freely. Check for restrictions, too
many equivalent feet, or too many elbows in the vent pipe.
Table 3 - Air Pressure Switch Parameters
BLOWER PROVER
Normally Open Contacts
Close on a rise in pressure
BLOCKED INTAKE
Normally Closed Contacts
Open on a fall in pressure
BLOCKED EXHAUST
Normally Closed Contacts
Open on a rise in pressure
+1.00” W.C.(± 0.05” W.C)
-2.00” W.C. (± 0.05” W.C)
+2.00” W.C. (+0.05” W.C)
Technical Literature Department
22 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
AIR PRESSURE SWITCH TESTING (CONT)
BLOWER PROVER SWITCH
PRESSURE TEST
BLOCKED INTAKE SWITCH
PRESSURE TEST
BLOCKED EXHAUST SWITCH
PRESSURE TEST
Technical Literature Department
23 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FLAME SENSING TEST
To prove burner flame during ignition the control system monitors flame sensing current
through the flame sensor. It is a DC micro amp (µA) current that flows through the flame
sensor. The control system must sense a minimum level of current to “prove” flame. The
minimum flame sensing current is approximately 1.0 µA. If flame sensing current remains
lower than 1.0 µA the control system would lock out after 3 failed trials for ignition and
display “Ignition Failure.” Flame sensing current typically runs much higher than minimum
when the flame sensor is clean; between 8.0 µA to 12.0 µA.
The most common cause of “Ignition Failure” lock out is a contaminated or corroded flame
sensor. Rust/corrosion will accumulate on the flame sensor over time. Cleaning the flame
sensor is a common maintenance procedure that should be performed anytime the water
heater is being serviced. Clean the flame sensor with ultra fine steel wool or an ultra fine
Scotch-Brite pad. DO NOT use a coarse abrasive material such as sand paper.
The burner not being grounded can also cause ignition failure - see page 8.
Measuring Flame Sensing Current
Measuring flame sensing current requires a multi meter with DC micro amp functionality.
sensor wire is disconnected and one of the meter probes is inserted in the wire connector.
The other meter probe touches the flame sensor terminal. There must be constant contact at
both points to measure current. Start the water heater - when ignition occurs the meter will
read flame sensing current in real time. See the image below.
Flame Sensor
If flame sensing current is lower than 8.0 µA, remove the flame sensor and clean it with ultra
fine steel wool. Perform a close visual inspection of the flame sensor. If the sensor appears
to be damaged or shows signs of excessive wear, replace the flame sensor. If the ceramic
insulator on the flame sensor has any visible cracks, replace the flame sensor. When
finished inspecting and cleaning the flame sensor, reinstall it and measure flame sensing
current again.
Technical Literature Department
24 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
IGNITER CURRENT TEST
The water heater covered by this Service Manual uses a hot surface igniter (HSI). The
amps). The more current flowing through the igniter; the hotter the igniter will be. The hotter
the igniter is; the more likely it will be to ignite the burner.
The normal resistance of the hot surface igniter (when new) will be between 40-70 ohms at
77°F (25°C). Hot surface igniters are wearing parts; with age and wear the resistance
(ohms) of the igniter will increase. As the resistance (ohms) increases the current (AC amps)
will decrease. More importantly the heat generated by the igniter will decrease at lower amp
draws. Over time hot surface Igniters will wear out and must be replaced as they will no
longer generate enough heat to cause ignition.
The control system is programmed to verify a minimum of 2.0 AC amps before it will initiate
a trial for ignition by energizing the gas valve (see Sequence of Operation page 40). If the
control system senses less than 2.0 igniter amps during the warm up period the control
system will lock out and display the “Low Igniter Current” fault message.
Igniter current can be measured at CCB J5 socket or at the igniter. Clip the amp meter
around one of the two igniter wires to measure igniter current. See the images below.
Service Notes - Hot Surface Igniters
It is a good practice to check igniter current when any service or maintenance is being
performed. Igniter current will be 4.0 to 5.0 AC amps when the igniter is new. Because hot
surface igniters are wearing parts they can cause intermittent ignition failure with age and
wear. Replacing the igniter when current is lower than 3.0 AC amps is a good preventive
maintenance procedure that can prevent loss of hot water and customer dissatisfaction.
Technical Literature Department
25 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CONTROL SYSTEM
INTRODUCTION
This portion of the service manual will cover the control system. The control system includes
several components: a UIM (User Interface Module), a CCB (Central Control Board), and an
Overlay/Button Pad. More information on these components will be given in the pages that
follow.
Control System Features
Advanced Diagnostics: Plain english text based diagnostic information (fault messages)
on board to help equipment owners accurately describe the reason for a given lock out
condition and service technicians quickly and accurately service the water heater.
Fault History Screen: Will retain a 9 event history of fault messages with a time stamp.
This will help diagnose load and/or environmental conditions that may be contributing to a
problem with operation or a lock-out.
Fault Occurrence Screen: Will keep a running total of how many times each lock out/fault
condition has occurred since the water heater was first installed. This is valuable information
for a service technician when trying to determine root causes for service problems.
Help Screens: Text based operational information to help the user understand how to
change settings, navigate the menu screens and what the various icons and displayed items
mean.
EMI / RFI Filtering: Built into all control system circuit boards. (EMI = Electro Magnetic
Interference, RFI = Radio Frequency Interference) Helps prevent or eliminate erratic
operation caused by EMI/RFI.
Technical Literature Department
26 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
UIM
The UIM (User Interface Module) is the display on the front of the water heater. The UIM’s
major components include a Circuit Board with LCD display and a Button Pad Overlay which
contains the five user input buttons.
Service Notes - Button Pad Ribbon Cable
The Ribbon Cable that connects the Button Pad Overlay to the UIM Circuit Board must be
plugged in exactly as shown in the images below; with the metal crimp connections visible
on the plug end and the UIM Circuit Board back facing out. There are six pins on this Ribbon
cable socket, Ensure all six pins are inserted into the Ribbon Cable plug whenever removing
or installing the UIM or Button Pad Overlay.
Failure to connect this Ribbon cable exactly as shown when servicing will render the User
Input Buttons inoperable. This should be checked whenever the nature of the service
complaint is an inoperable or unresponsive controller or UIM.
UIM Circuit Board Back
Button Pad Overlay
J3 Socket - Button Pad
Communication
J2 Socket - CCB
Communication
Ribbon Cable To
Button Pad
Ensure Ribbon Cable Plug
is inserted exactly as shown.
LCD
Screen
UIM Circuit Board Front
Technical Literature Department
27 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
UIM (CONT)
User input buttons on the UIM include an Up, a Down, and three Operational buttons.
The Up and Down buttons are used to navigate through the various menus and screens
displayed and to adjust or change user settings such as the Operating Set Point.
The three Operational buttons are multifunctional. Their function is defined by the text that
appears above each button on the UIM display. The Operational button’s function will
change depending on what menu or screen is currently displayed.
Commercial & Residential Product Differences
The illustration below shows the control system’s “Desktop” screen. This is the control
system’s default screen. If there are no active fault messages and no user input for
approximately 10 minutes the control system will return to this screen automatically.
The water heater covered by this Service Manual is available in commercial and residential
models. The “Tank Temperature” data shown on the desktop screen below will not be visible
on residential models. Tank Temperature will be displayed on the commercial models only.
The maximum Operating Set Point for a residential model will be 160°F (71°C). Maximum
Operating Set Point on commercial models will be 180°F (82°C).
UIM - User Interface Module Display
Up & Down
Buttons
Operational
Buttons
Discreet Menu - Contact Information
While viewing the Desktop screen (above). Press and hold down the middle Operational
button for 30 seconds and then release it. This will launch a discreet menu with a provision
for entering personalized contact information. Installing contractors and/or service
technicians can enter their company name and telephone number. This contact information
would be displayed with all fault messages whenever the control system was in a lock out
condition.
Technical Literature Department
28 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
UIM (CONT)
Desktop Screen
The Desktop screen is the default screen. If there are no active fault messages the display
will return to this screen with no user input after approximately 10 minutes. The Desktop
screen displays text and icons that provide operational and diagnostic information.
The first line of text on the Desktop screen is the temperature of the water inside the tank.
Tank Temperature data will only be visible on commercial models.
The second line of text on the Desktop screen is the Operating Set Point. The Operating
Set Point is a user setting that can be adjusted in the Temperatures Menu. The Operating
Set Point is the temperature at which the water heater will maintain the water inside the tank.
The third line of text on the Desktop screen shows the current Status of the control system.
The current Operational State of the water heater’s control system is displayed in real time.
Operational States are explained on page 31.
CONTROL SYSTEM DESKTOP SCREEN
Discreet Menu - Contact Information
While viewing the Desktop screen
(left). Press and hold down the middle
Operational button for 30 seconds
then release it. This will launch a
discreet menu that contains a
provision for adding personalized
contact information that will be
displayed on all fault message
screens. The installing contractor or
service agent can enter their
company name and phone number to
help the home or business owner
contact them for service.
Note: Tank Temperature will only be visible on commercial models.
Service Note - Sequence of Operation Display
The Desktop screen displays the Sequence of Operation in real time using animated “Status
Icons.” This is valuable information when servicing the water heater that can help correctly
diagnose service problems more quickly.
troubleshooting the water heater. IE: if the Igniter Status Icon comes on but the Check Mark
Status Icon does not appear next to it within 5 seconds the control system has not sensed
minimum igniter current of 2.0 AC amps.
Technical Literature Department
29 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
UIM (CONT)
Table 4 - Status Icons
STATUS ICON
DESCRIPTION
The temperature of the water in the tank has fallen and the water heater will now initialize
a new heating cycle.
The temperature of the water in the tank has reached the Operating Set Point.
The control is unable to initiate any further heating cycles. This is usually caused by a
fault condition detected by the control.
The blower is being energized.
The Blower Prover Air Pressure Switch contacts have closed. Check Mark Icon is visual
confirmation of contact closure.
The igniter has been energized.
The igniter has been energized and the control system has sensed minimum (2.0 AC
amps).Check Mark Icon is visual confirmation of minimum igniter current.
The gas valve has been energized.
The control system has sensed minimum (1.0 µA) DC micro amps.Flame Icon is visual
confirmation of minimum flame sensing current.
The control has detected a fault condition.
The control has detected a warning condition. These conditions will not cause the control
system to lock out (discontinue water heater operation), but does merit attention.
Technical Literature Department
30 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
UIM (CONT)
Table 5 - Operational States (Modes)
STATE
DESCRIPTION
The water heater is not in an active heating cycle. This usually means the temperature
in the tank has reached Operating Set Point and has not dropped low enough to initiate
a call for heat.
Standby
Input Verification
Pre-Purge
The control system is waiting for specific conditions to occur (primarily pressure switch
Operation.
The blower has been energized - the control system is purging out any excess gas or
left over products of combustion from the heat exchanger at the beginning of each
heating cycle.
The igniter has been energized and is currently warming up to ensure proper ignition -
typically last 17-20 seconds.
Igniter Warmup
The control system is allowing for a steady burner flame to be established. Duration of
this and the Ignition Verification state is typically 4-6 seconds.
Ignition Activation
Ignition Verification Assurance of proper flame sense is being determined.
After a failed trial for ignition the control system is purging out any excess gas or left
over products of combustion from the heat exchanger before another trail for ignition.
Inter-Purge
Heating
Burner flame has been properly established - minimum flame sensing current has
been verified by the control system - water in the tank is being heated.
The control system is purging out any excess gas or left over products of combustion
from the heat exchanger after a successful heating cycle.
Post-Purge
The control system has detected a fault and declared a fault condition. The control
that caused the lock out must be corrected before the water heater can resume a
heating cycle.
Fault
Technical Literature Department
31 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
OPERATING SET POINT ADJUSTMENT
When the temperature sensed by the control system at the Temperature Probe (top of the
water heater) reaches the Operating Set Point the control system will end the heating cycle.
A call for heat will be activated again when the tank temperature drops below the Operating
Set Point minus the Differential setting plus one degree.
Example: Operating Set Point is 120°, Differential setting is 2° (factory default). A call for
heat will be activated when tank temperature drops to 117°. 120 - (2+1) = 117.
The Operating Set Point and the Differential setting is adjusted or changed in the
Temperatures menu. The following illustrations and instructions will explain how to adjust
these user settings and navigate the control system menus.
ACTION
DISPLAY
From the desktop screen, press MENU.
NOTE: Notice how the text on the UIM display above the
Operational Buttons changes as you navigate through
the various menus and screens.
With Temperatures selected (highlighted in black) in the
Main Menu, press the Operational Button underneath
“SELECT” to enter the Temperatures Menu.
If Temperatures is not selected use the Up and Down
buttons to select this menu item.
With the Operating Set Point selected in the
Temperatures Menu, press the Operational Button
underneath “CHANGE” to activate the adjustment mode
for this menu item.
NOTE: The Upper Probe Offset can be used to override
the control system’s calculated tank temperature by 5°
above or below current reading. Adjustable range is -5°F
to +5°F.
Press the UP and DOWN buttons to adjust the Operating
Set Point to the desired setting.
Press the Operational Button underneath “UPDATE” to
confirm the new setting or “CANCEL” to discard the new
setting and retain the previous setting.
NOTE: This same procedure can also be used to adjust
the Differential and the Upper Probe Offset user settings.
Technical Literature Department
32 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CONTROL SYSTEM MENUS
Desktop: This is the default screen for the control system. If there are no active faults or
warnings the display will return to this screen with no user input after approximately 10
minutes. Information/settings available:
• Tank Temperature (commercial models only)
• Operating Set Point
• Operating States
• Status (Graphical) Icons
Temperatures: This menu contains the user settings and temperature information.
Information/settings available:
• Operating Set Point - adjustable (90-180°F commercial models, 90-160°F residential models)
• Differential - adjustable (2-20° factory setting is 2°)
• Upper Temperature (commercial models only)
• (Heater Regulated to Upper) configuration information
• Upper Probe Offset - adjustable -5°F to +5°F. overrides the perceived tank temp by this setting.
Heater Status: This menu shows the current operating state of the water heater, Blower,
Igniter, Gas Valve and the state of the contacts (open/closed) for the air pressure switches
and the ECO along with the state of the CCB S1 dip switches. Information shown in this
menu is in real time. Information/settings available:
• ECO Contact - open or closed
• Blocked Inlet PS - air pressure switch contacts open or closed
• Blocked Outlet PS - air pressure switch contacts open or closed
• Blower Prover PS - air pressure switch contacts open or closed
• Blower Low On - blower is running at low speed yes/no (N/A models equipped w/ 2 speed blowers)
• Blower High On - blower is running at high speed yes/no
• Igniter On - is currently energized yes/no (yes = energized; no = not energized)
• Igniter Current - igniter current is above minimum 2.0 AC amps yes/no
• Gas Valve On - is currently energized yes/no (yes = energized; no = not energized)
• Flame Detected - flame sensing current is above minimum 1.0 µA yes/no
• External Input Enabled - external control enable/disable circuit activated yes/no
• Ignition Trials - maximum number of retries for ignition 1 or 3 S1 dip switch setting (see page 38)
Display Settings: This menu contains user settings for the UIM display contrast, back light
and temperature units. Information/settings available:
• Temperature Units - adjustable Celsius or or Fahrenheit
• Backlight Delay - adjustable - seconds to continuous
• Contrast - adjustable
Technical Literature Department
33 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CONTROL SYSTEM MENUS (CONT)
Heater Information: This menu contains historic operational and configuration information.
Information/settings available:
• Elapsed Time - hrs & mins - how long the water heater has been powered on
• Burner On Time - hrs & mins - burner run time cumulative
• Cycle Count - total number of heating cycles
• Ignition Failure Count - total number of ignition failures
• Flame Loss Count - total number of lost flame events
• CCB Version - software revision of the control systems CCB circuit board
• UIM Version -software revision of the control systems UIM circuit board
• Configuration - manufacturer and model number configuration
Current Fault: This menu will only contain information when the water heater is in a lock out
condition. It will contain the current fault message/condition.
Fault History: This menu contains a history of fault occurrences with a time stamp. The
time stamp associated with the fault condition can be subtracted from the “Elapsed Time” in
the “Heater Information” menu to determine when or how long ago the given event occurred.
The control system will keep the last 9 events in history. When a new event occurs the oldest
event will be lost.
Fault Occurrence: This menu contains a running total (cumulative) for all fault conditions
declared by the control system. This information can be useful in determining root causes for
service problems. Information/settings available:
• Ignition Failure
• ECO
• Blocked Inlet
• Blocked Outlet
• Thermostat Input 4
• Blower Prover
• Flame Detect Error
• Flame Probe
• External Output Relay
• Gas Valve
• Igniter Fail
• Power Supply Fail
• CCB Hardware
• Model Faults
• CCB Communications
Restore Factory Defaults: This menu allows the end user to restore all settings to their
factory defaults.
Help Menu: This menu contains information to help users use the control system, menu
items include; Operating Instructions, Status Icon Legend, Operating States, Adjust
Operating Set Point, Change Display Units, Restore Factory Defaults, Contact Information.
Technical Literature Department
34 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CCB
The CCB circuit board is the main control. All instructions for ignition and temperature
control originate from this circuit board. Diagnostic and operational messages are generated
the igniter, blower, gas valve, and temperature probe are directly connected to one of the
CCB’s socket connectors.
Service Notes - CCB Replacement
If the CCB fails and needs to be replaced the replacement board will be shipped with the
gray plastic enclosure and a new 24 VAC transformer. There is no need to remove the circuit
board from the enclosure when the CCB is being replaced.
Enclosure With Front Removed
CCB Circuit Board
Transformer
120V x 24V
50 VA
Technical Literature Department
35 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CCB (CONT)
Socket Identification
All wiring connections and sockets will be identified in the following pages. The
Troubleshooting section of this Service Manual will refer back to this illustration and
information.
1
2
3
4
5
1
2
3
4
1
2
4
1
2
J4
J5
J3
J2
J1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
S1
J6
4
3
2
1
J7
J9
J13
J11
1
2
3
4
5
6
7
8
J10
J16
1
3
J15
1
2
4
2
Technical Literature Department
36 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CCB (CONT)
J1 Socket - Transformer
PIN #
DESCRIPTION
1
2
3
4
5
120 VAC hot to transformer
Not used
120 VAC neutral to transformer
24 VAC out from transformer
24 VAC out from transformer
J2 Socket - 120 VAC To Blower
PIN #
DESCRIPTION
DESCRIPTION
1
2
3
4
120 VAC hot to blower
120 VAC neutral to blower
Not used
Not used
J3 Socket - 120 VAC Power Supply
PIN #
1
2
3
120 VAC hot
Earth Ground
120 VAC neutral
J4 Flame Sensor - Male Spade Connector
J5 Socket - Igniter 120 VAC HSI (hot surface igniter - Silicon Carbide)
PIN #
DESCRIPTION
1
2
120 VAC hot
120 VAC neutral
J6 Socket - Gas Valve, Pressure Switches, Enable/Disable Circuit
PIN #
DESCRIPTION
1
2
Not used
Gas valve - 24 VAC
Not used
3
4
Blocked Intake air pressure switch
5
Blocked Exhaust air pressure switch
Blower Prover air pressure switch
Blower Prover air pressure switch
Enable/disable external control circuit - jumper installed from factory
Not used
6
7
8
9
10
11
12
13
14
15
Blocked Exhaust air pressure switch
Enable/disable external control circuit - jumper installed from factory
Not used
Not used
Blocked Intake air pressure switch
Gas valve - 24 VAC
Technical Literature Department
37 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CCB (CONT)
J7 Socket - Temperature Probe/ECO (immersion probe - top of the water heater)
PIN #
DESCRIPTION
ECO (energy cut out) 24 VAC out (red wire)
1
2
3
4
Upper temperature probe (thermistor) +5.0 VDC (black wire)
Upper temperature probe (thermistor) -5.0 VDC (black wire)
ECO (energy cut out) 24 VAC return (red wire)
J9 Port - Communication Port - Not Used
J10 Socket - Not Used
J11 Port - Communication Port - Not Used
J13 Socket - Blower Speed Control (VFD)
PIN #
DESCRIPTION
1
2
3
4
5
6
7
8
Not used
Not used
Not used
Not used
Not used
J15 Socket - Not Used
J16 Port - Communication Port - UIM Display (user interface module)
S1 Dip Switch
The S1 dip switches are configured from the factory and should not be changed. The
illustration below shows the 4 dip switches with labeling. Dip switches are toggle type micro
switches. Flipping a dip switch towards “Open” would be the same as “Off.” Flipping a dip
switch the other way (towards the switch numbers) is the same as “On.”
Dip switch #1 is used to configure the water heater to declare a fault condition and lock out
after one or three failed trials for ignition. The factory setting is “on” for three trials.
Dip switches #2 and #3 are used when this control system is installed on other products.
The factory setting for these two dip switches is “on.”
Dip switch #4 is a spare, configuration does not matter.
3
1 Retry
Retries
Use Yes
Type Tstat
Spare
No
OFF
OPEN
ON
CLOSED
Ext
Input
Vent
Spare
Technical Literature Department
38 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
WIRING DIAGRAM
120 VAC 1Ø
Power Supply
Ground
Neutral
Hot
Service Notes - Polarity & Ground
This water heater is polarity and ground sensitive. The control system will lock out and
display a fault message (“AC Reversed”) if the power supply polarity is reversed. Flame
sensing current cannot be established if the burner is not grounded which will lead to ignition
failure. See electrical requirements on page 8.
Technical Literature Department
39 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
SEQUENCE OF OPERATION
Call for heat initiated
Control System Declares
Fault Condition - Locks Out
One of the following
Fault Messages Displayed:
Air Pressure Switch Test Is Performed
Blower Prover Switch is verified open
NO
Blocked Intake and Blocked Exhaust Switches are verified closed
“Blower Prover Failure”
“Blocked Inlet”
“Blocked Exhaust Vent”
YES
Blower Motor is energized
Pre-purge State
Control System Declares
Fault Condition - Locks Out
“Blower Prover Open”
Fault Message Displayed
Blower Prover Switch is verified closed
NO
YES
Igniter is energized for warm up period
(approx 17 seconds)
Control System Declares
Fault Condition - Locks Out
“Low Igniter Current”
Control System (CCB) Verifies Igniter
Current at 2.0 AC Amps Minimum
NO
Fault Message Displayed
YES
Gas Valve Is Energized
Gas Flows To Burner
Control System (CCB) Verifies Flame
Sensing Current at 1.0µA DC Micro Amps Minimum
YES
NO
Water Is Heated To
Operating Set Point
Gas Valve Is
De-energized
Gas Valve Is
De-energized
Inter-Purge State
30 Sec Approx
Post-Purge State
30 Sec Approx
Retries Up To
3 Times
Control System Declares
Control System Goes Into
Standby State/Mode
Fault Condition - Locks Out
“Ignition Failure”
Fault Message Displayed
Technical Literature Department
40 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
TROUBLESHOOTING
The control system performs exhaustive self diagnostics and displays detected fault
When the control system declares a fault condition it will “lock out” and disable heating.
Troubleshooting procedures for the most common error messages are covered in this
manual. In the tables that follow the first column shows the fault message as displayed by
the UIM along with an explanation. The second column details things to check or repair.
Rough Starting - Rough Operation Note:
If the water heater is experiencing rough operation or rough starting review the Service
Notes - Blower Flange & Blower Adapter Gaskets on page 13. Remove and inspect the
Heater Status Menu
Blower, Igniter and Gas Valve. The state (open/closed) of the contacts for the Blower Prover,
Blocked Intake and Blocked Exhaust Switches. This information and more is shown in real
time. Use this menu when troubleshooting the water heater to quickly and accurately
diagnose operational problems.
Things to check before servicing
• Using the Instruction Manual that came with the water heater as reference, verify the
water piping, gas line, venting and electrical have all been properly installed.
• Ensure 120 VAC is supplied to the water heater and that the polarity is correct per the
electrical requirements on page 8.
established unless the burner is grounded. This can cause ignition failure, after three
failed trials for ignition the UIM would display the “Ignition Failure” fault message.
Resetting the control system
To reset the control system from a lock out condition; turn the power supply off for
approximately 20 seconds and then back on. Keep in mind if the condition that caused the
fault has not been corrected the control system will continue to lock out.
Important Service Reminder
When performing any troubleshooting step outlined in this Service Manual always consider
the wiring and connectors between components. Perform a close visual inspection of all
wiring and connectors to and from a given component before replacement. Ensure wires
were stripped before being crimped in a wire connector, ensure wires are crimped tightly in
their connectors, ensure connection pins in sockets and plugs are not damaged or worn,
ensure plugs and sockets are mating properly and providing good contact.
Failure to perform this critical step or failing to perform this step thoroughly often results in
needless down time, unnecessary parts replacement, and customer dissatisfaction.
Technical Literature Department
41 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
CONTROL SYSTEM UNRESPONSIVE
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
•
Ensure the on/off switch is on and working -
replace switch if defective.
UIM Display Is Blank
On/Off is turned off
Check communication cable connections at
new comm cable. (standard Cat 5 network
cable).
Water heater is not plugged in
Tripped Breaker - Blown Fuses
120 VAC power supply problems
24 VAC power supply problems
Defective transformer
•
•
•
Closely inspect communication ports on CCB
and UIM for damage or wear.
Wiring or plug/socket connection problems
UIM communication cable problems
Ensure 120 VAC power is properly connected in
the junction box on the back of the water heater.
Important Service Reminder:
Ensure 120 VAC is supplied to CCB’s J3 Socket
pins 1 & 3. Hot wire to pin 1, neutral wire to pin 3
When performing any troubleshooting steps outlined
in this service manual always consider the wiring
and connectors between components. Perform a
close visual inspection of all wiring and connectors
to a given component before replacement.
•
•
•
Check 120 VAC to transformer primary winding
plug removed, power on.
Ensure wires were stripped before being crimped in
a wire connector, ensure wires are crimped tightly in
their connectors, ensure connection pins in sockets
and plugs are not damaged or worn, ensure plugs
and sockets are mating properly and providing good
contact.
Check J1 plug and J1 socket on the CCB for
wear or damage. Ensure plugs and sockets are
mating properly and providing good contact.
Check for 24 VAC from transformer secondary
winding at CCB’s J1 socket pins 4 & 5 with J1
plug inserted, power on. If 24 VAC is not present
AND the two checks above were performed and
the results were successful - replace the trans-
former. Check all wiring for shorts before power-
ing up the new transformer.
Failure to perform this critical step or failing to
perform this step thoroughly often results in
needless down time, unnecessary parts
replacement, and customer dissatisfaction.
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
•
•
Ensure Ribbon Cable from the Button overlay is
inserted correctly in UIM J3 Socket (page 27).
UIM is Inoperable
UIM does not respond to any user input using the
operational and/or Up and Down buttons.
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Water heater may be maintaining water temperature
at the last saved setting or may not be operating at
all.
Technical Literature Department
42 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES
DISPLAYED MESSAGE
CONDITION/INDICATES
CHECK/REPAIR
•
•
Check incoming power supply wiring to the
water heater in the junction box - ensure that
the hot wire is connected to the water heater’s
black wire and the neutral wire is connected to
the water heater’s white wire inside the junction
box. See electrical requirements on page 8.
“AC Reversed”
The control system has detected the power supply
polarity is reversed.
Check for 120 VAC at CCB’s J3 Socket (page
36) pins 1 & 3 with J3 plug inserted, power on.
Check for AC voltage between pin 1 and ground
- should indicate 120 VAC.
Check for AC voltage between pin 3 and ground
- should indicate 0 VAC.
•
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Check Temperature Probe plug and socket con-
close visual inspection of the pins inside the
plug and socket - ensure plugs and sockets are
mating properly and providing good contact.
“Upper Probe Open”
The control system has detected over 56,000 ohms
from the Temperature Probe on top of the water
heater.
•
•
Check all wiring between the Temperature
Probe and the J7 Socket on the CCB. Repair/
replace anything worn or damaged.
Unplug J7 plug from CCB, check resistance
between the two black wires in the plug end with
an ohm meter. If resistance is above 56,000
ohms - replace the Temperature Probe.
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Technical Literature Department
43 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
•
Check all wiring between the Temperature
Repair/replace anything worn or damaged.
“Upper Probe Short”
The control system has detected less than 390
ohms from the Temperature Probe on top of the
water heater.
Unplug J7 plug from CCB, check resistance
between the two black wires in the plug end with
an ohm meter. If resistance is at or below 390
ohms - replace the Temperature Probe.
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
•
•
•
Disconnect the wire from the flame sensor (see
flame sensor and ground with an ohm meter.
There should be no continuity - infinite resis-
tance.
“Flame Probe Short”
The control system has detected that the flame
sensor is grounded.
If above test indicates there is continuity
between the flame sensor and ground - remove
the flame sensor is not bent and touching the
burner.
Check all flame sensor wiring between the
flame sensor and the J4 male spade connector
pinched wires or shorts - repair/replace anything
worn or damaged.
•
•
Replace the flame sensor.
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Technical Literature Department
44 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
The burner has not shut down properly. Check
gas valve for 100% closure. Check for flame
candling after the heating cycle has ended
“Flame Detect Error”
The control system has detected flame sensing
current out of sequence.
•
•
If burner flame is candling after the heating
cycle has ended - replace gas valve assembly,
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
•
•
Be extremely careful - record temperature from
a nearby hot water fixture.
“Energy Cut Out (ECO)”
The control system has detected water temperature
in the tank above 190°F. Tank temperature must cool
to 140°F before the fault message (lock out) can be
reset. Cycle power off (20 seconds) and on again to
reset.
If recorded temperature is above 180°F - shut
off power and gas to the water heater and call
the technical support phone number shown on
the water heater labeling for further assistance.
DO NOT LEAVE THE WATER HEATER IN
OPERATION.
•
If recorded temperature from above is well
below 180°- cycle power to reset the control
system. Watch the water heater through several
heating cycles. If tank temperature climbs to
excessively high temperatures - shut off power
and gas to the water heater and call the techni-
cal support phone number shown on the water
heater labeling for further assistance. DO NOT
LEAVE THE WATER HEATER IN OPERATION.
•
Check Temperature Probe plug and socket con-
close visual inspection of the pins inside the
plug and socket - ensure plugs and sockets are
mating properly and providing good contact.
•
•
Check all wiring between the Temperature
Probe and the J7 Socket on the CCB. Repair/
replace anything worn or damaged.
With the J7 plug disconnected from the CCB
red wires in the plug end (pins 1 & 4) with an
ohm meter. If there is no continuity between
these two wires and the tank temperature is not
excessive - replace the Temperature Probe.
Technical Literature Department
45 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
If the water heater has been installed as a con-
ventional vent appliance - Ensure the intake air
connection screen is not clogged with debris.
See Service Notes - Venting on page 7.
“Blocked Inlet”
The control system has detected open contacts at
the Blocked Intake air pressure switch - inadequate
supply of intake (combustion) air.
•
If water heater has been installed as a direct
vent appliance - check for restrictions, too many
equivalent feet, or too many elbows in the intake
air piping. Review venting installation section of
the Instruction Manual that came with the water
Ensure the vent/intake air piping has been
installed within manufacturers requirements.
•
•
If water heater has been installed as a direct
vent appliance - temporarily disconnect the
intake air pipe at the blower connection on the
water heater - ensure the screen inside the
intake air connection was removed during
installation. See the Service Notes for venting
on page 7.
Check all wiring between the Blocked Intake air
pressure switch and the CCB’s J6 Socket (page
36) pins 4 & 14. Perform close visual inspection
of the pins inside the plug and socket - ensure
plugs and sockets are mating properly and pro-
viding good contact. Repair/replace anything
worn or damaged.
•
•
Review the air pressure switch information
switch test procedure for the Blocked Intake air
pressure switch - see pages 21 through 23.
Replace the Blocked Intake switch if defective.
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Technical Literature Department
46 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
•
Check for restrictions, too many equivalent feet,
or too many elbows in the vent pipe. Ensure
“Blocked Exhaust Vent”
The control system has detected open contacts at
the Blocked Exhaust air pressure switch - the water
heater is not venting properly.
Review venting installation section of the
Instruction Manual that came with the water
Ensure the vent/intake air piping has been
installed within manufacturers requirements.
•
•
Check all wiring between the Blocked Exhaust
air pressure switch and the CCB’s J6 Socket
inspection of the pins inside the plug and socket
- ensure plugs and sockets are mating properly
and providing good contact. Repair/replace any-
thing worn or damaged.
Review the air pressure switch information
switch test procedure for the Blocked Exhaust
Replace the Blocked Exhaust switch if defec-
tive.
•
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Check all wiring between the Blower Prover air
pressure switch and the CCB’s J6 Socket (page
36) pins 6 & 7. Ensure there are no shorted or
pinched wires.
“Blower Prover Failure”
The control system has detected closed contacts at
the Blower Prover air pressure switch out of
sequence. Blower Prover air pressure switch
contacts should be open at the beginning of each
heating cycle - see the Sequence of Operation on
•
•
•
Ensure there are no jumper wires installed on
the Blower Prover switch.
Ensure there are no jumper wires installed
between the CCB’s J6 Socket pins 6 & 7.
Review the air pressure switch information
switch test procedure for the Blower Prover air
pressure switch - see pages 21 through 23.
Replace the Blower Prover switch if defective.
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Technical Literature Department
47 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
PERFORM ALL THESE TESTS WITH POWER
TURNED ON AND A CALL FOR HEAT ACTIVE.
“Blower Prover Open”
(Blower Not Running)
•
Check for 120 VAC at the CCB’s J2 Socket
inspection of the pins inside the plug and socket
- ensure plugs and sockets are mating properly
and providing good contact.
The control system has detected open contacts at
the Blower Prover air pressure switch after Blower
has been energized.
•
•
•
Check all wiring between CCB’s J2 Socket pins
1 & 2 and the blower motor assembly’s high
Disconnect the plug at the blower motor assem-
bly’s high voltage 3 Pin Socket - check for 120
VAC at the plug end.
Perform close visual inspection of the pins
inside the plug and socket at the blower motor
assembly’s high voltage 3 Pin Socket - ensure
plugs and sockets are mating properly and pro-
viding good contact.
•
•
Disconnect the plug at the blower assembly’s
the Blower has not been running prior and starts
running when this plug is disconnected - call the
technical support phone number shown on the
water heater labeling for further assistance.
Ensure the Blower Prover air pressure switch
sensing tube is connected properly at both ends
and that it is not kinked or damaged. Repair/
replace anything worn or damaged as neces-
sary.
“Blower Prover Open”
(Blower Is Running)
The control system has detected open contacts at
the Blower Prover air pressure switch after Blower
has been energized.
•
•
•
Check all wiring between CCB’s J6 Socket
(page 35) pins 6 & 7 and the Blower Prover air
pressure switch. Repair/replace anything worn
or damaged as necessary.
Perform close visual inspection of the pins
inside the CCB J6 plug and socket - ensure
plugs and sockets are mating properly and pro-
viding good contact.
Review the air pressure switch information
switch test procedure for the Blower Prover air
pressure switch - see pages 21 through 23.
Replace the Blower Prover switch if defective.
Technical Literature Department
48 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
Check all wiring between CCB’s J5 Socket
(page 35) pins 1 & 2 and the hot surface igniter.
Repair/replace anything worn or damaged as
necessary.
“Low Igniter Current”
The control system has detected less than 2.0 AC
amps through the igniter during the igniter warm up
period.
•
Perform close visual inspection of the pins
inside the CCB J5 plug and socket - ensure
plugs and sockets are mating properly and pro-
viding good contact. Repair/replace anything
worn or damaged as necessary.
•
With power turned on and a call for heat active -
ensure there is 120 VAC between pins 1 & 2 of
the CCB’s J5 Socket during the igniter warm up
period. - the igniter lighting bolt icon will appear
on the UIM display during the igniter warm up
•
•
Turn off power to the water heater - disconnect
wires to igniter at the igniter. Check for continu-
ity between the two igniter wires. If the igniter
shows to be an open circuit - replace the igniter.
With power turned on and a call for heat active -
check amp draw through the igniter with an AC
amp meter during the igniter warm up period.
This procedure is illustrated and explained on
than 3.0 AC amps.
•
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Technical Literature Department
49 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
Visually check for burner flame through the view
port on the top of the water heater (see illustra-
Valve icon will appear on UIM display during this
operating state.
“Ignition Failure”
The control system has detected less than 1.0 µA
(DC micro amps) through the flame sensor during
the Ignition Verification operating state on three
consecutive trials for ignition.
•
•
Ensure the gas supply shut off valve is open.
Ensure there is adequate air for combustion &
ventilation. See air requirements in the Instruc-
tion Manual that came with the water heater.
•
•
Ensure the burner is grounded - see electrical
requirements and service notes on page 8.
Ensure flame sensor wiring is plugged in
securely at the CCB’s J4 male spade connector
(page 35) and at the flame sensor wiring termi-
•
•
Check all wiring between the flame sensor and
the CCB J4 connection. Repair/replace anything
worn or damaged as necessary.
Rough Starting - Rough Operation Note:
If the water heater is experiencing rough operation
or rough starting review the Service Notes - Blower
Remove and clean the flame sensor (page 24)
with fine steel wool - check for signs of exces-
sive wear, bent, damage, cracks in the insulator
- replace flame sensor if worn or damaged.
Call the technical support phone number shown on
the water heater labeling for further assistance if the
problem has not been corrected after performing the
procedures outlined here.
•
Check for flame sensing current during the Igni-
tion Verification operating state - Gas Valve icon
Flame sensing current test procedure is illus-
trated and explained on page 24.
If flame sensing current measured is well above
the 1.0 µA (DC micro amps) minimum during
this test and the control system continues to
declare the Ignition Failure fault condition after
three trials - call the technical support phone
number shown on the water heater labeling for
further assistance.
If the flame sensing current measured is not
established or is below 1.0 µA - continue to the
next check/repair procedure.
Technical Literature Department
50 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
Check for 24 VAC to the Gas Valve solenoid coil
at the in-line male/female spade connectors
during the Ignition Activation operating state
(Gas Valve icon will be visible on the UIM dis-
play during this period).
“Ignition Failure”
The control system has detected less than 1.0 µA
(DC micro amps) through the flame sensor during
the Ignition Verification operating state on three
consecutive trials for ignition.
•
Check all wiring, plugs, and sockets between
the Gas valve solenoid coil and CCB’s J6
Socket pins 2 & 15 (page 35). Repair/replace
anything worn or damaged.
If 24 VAC is not being sent to the Gas Valve
solenoid coil during the Ignition Activation oper-
ating state and all wiring, plugs, and sockets are
in good condition and making good contact - call
the technical support phone number shown on
the water heater labeling for further assistance.
•
Check supply and manifold gas pressures. This
procedure is illustrated and explained on pages
Rough Starting - Rough Operation Note:
If the water heater is experiencing rough operation
or rough starting review the Service Notes - Blower
If supply gas pressure is below the minimum
raise/restore supply gas pressure to minimum
requirement. If supply gas pressure is above
maximum requirement - reduce supply gas
pressure below maximum requirement.
Call the technical support phone number shown on
the water heater labeling for further assistance if the
problem has not been corrected after performing the
procedures outlined here.
If there is not a rise in manifold pressure and a
corresponding drop in supply gas pressure
when the Gas Valve is energized as outlined on
ing or is clogged and is not allowing gas to flow
to the burner - continue to the next procedure.
•
•
Remove the Gas Valve and ensure the gas ori-
fice and gasket are installed properly and that
the correct size orifice for the fuel type is
installed. The procedure for removing the gas
valve to check the gas orifice is illustrated and
any signs of damage - replace if necessary.
Remove the burner and inspect it for damage or
debris that may have collected inside the burner
and be causing the ignition failure. The burner
removal procedure is illustrated and explained
aged or severely clogged with debris - replace
the burner.
Technical Literature Department
51 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
ULTRA HIGH EFFICIENCY POWER VENT/POWER DIRECT VENT - SERVICE MANUAL
FAULT MESSAGES (CONT)
DISPLAYED MESSAGE
CHECK/REPAIR
CONDITION/INDICATES
•
•
•
Turn off power - check all wiring and connectors
between the CCB’s J6 Socket (page 35) pins 2
& 15 and the Gas Valve’s solenoid coil. Repair/
replace anything worn or damaged as neces-
sary.
“Gas Valve Failure”
The control system has not detected any current
through the gas valve after it has been energized.
Perform close visual inspection of the pins
inside the CCB J6 plug and socket - ensure
plugs and sockets are mating properly and pro-
viding good contact. Repair/replace anything
worn or damaged as necessary.
Turn off power - disconnect the Gas Valve wir-
ing plug on top of the Gas Valve solenoid coil.
Check Gas Valve solenoid coil resistance with
an ohm meter at the solenoid coil terminals.
Normal resistance is approximately 7 million
ohms. If the Gas Valve solenoid coil is an open
circuit - replace the Gas Valve.
•
•
Check for 24 VAC at CCB’s J6 Socket pins 2 &
15 during the Ignition Activation operating state
(the Gas Valve status icon will be visible on the
UIM display during this period.
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
•
Turn off power - check the communication cable
connections between the J2 Socket on the UIM
(page 35).
“Communication Failure”
Loss of communication between the CCB and the
UIM.
•
•
Try a new communication cable (standard cate-
gory V network cable) between the CCB and the
UIM.
Call the technical support phone number shown
on the water heater labeling for further assis-
tance if the problem has not been corrected
after performing the procedures outlined here.
Technical Literature Department
52 of 52
Ashland City, TN © 2008
Servicing should only be performed by a Qualified Service Agent
Download from Www.Somanuals.com. All Manuals Search And Download.
500 Tennessee Waltz Parkway
Ashland City, TN 37015
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Snapper Lawn Mower ZF2200K User Manual
Sony DVD Player BDP S280 User Manual
Sony MiniDisc Player MDS PC1 User Manual
Sony MiniDisc Player MDS W1 User Manual
Speco Technologies Power Supply PSR 12S User Manual
StarTechcom Network Cables USBDUP15 User Manual
StarTechcom Server ECS0016 User Manual
Sub Zero Refrigerator ICBBI 30U User Manual
Sunbeam Wok WW4500D User Manual
Sylvania Flat Panel Television LD195SL8 User Manual