43-5522.fm Page 1 Tuesday, September 12, 2000 3:12 PM
2.4 GHz Digital Spread
Spectrum Dual Keypad
Cordless Phone
with Caller ID/Call Waiting
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 3 Tuesday, September 12, 2000 3:12 PM
This phone has been tested and found to
comply with all applicable UL and FCC stan-
dards.
READ THIS BEFORE
INSTALLATION
We have designed your phone to conform to
federal regulations, and you can connect it to
most telephone lines. However, each phone
(and each device, such as a telephone or an-
swering machine) that you connect to the
telephone line draws power from the tele-
phone line. We refer to this power draw as
the device's ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
WARNING:
shock hazard, do not expose this product to rain
or moisture.
To reduce the risk of fire or
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
If you use more than one phone or other de-
vice on the line, add up all of the RENs. If the
total is more than five (or three in rural ar-
eas), your telephones might not ring. If ringer
operation is impaired, remove a device from
the line.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
Your phone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC registration number and the REN to
your telephone company. Both numbers are
on the bottom of your phone.
This symbol is intended to inform
you that important operating and
Note:
You must not connect your phone to:
maintenance instructions are
included in the literature accom-
panying this product.
!
• coin-operated systems
• party-line systems
• most electronic key telephone systems
Important:
IMPORTANT CALLER ID
INFORMATION
To use the phone's Caller ID and Call Wait-
ing with Caller ID features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company. Where
Caller ID is offered, one or more options are
generally available:
• Cordless phones such as this one
require AC power to operate. When the
AC power is off, you cannot dial out or
receive incoming calls using your
phone. For this reason, the phone
should not be your only telephone. To be
safe, you should also have a phone that
does not require AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an AC
power failure.
• caller's number only
• caller's name only
• caller's name and number.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 4 Tuesday, September 12, 2000 3:12 PM
• Some cordless phones operate at fre-
quencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base of
the cordless phone should not be placed
near or on top of a TV or VCR.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
• Your cordless phone operates on stan-
dard radio frequencies, as allocated by
the FCC. Even though your phone's
access protection code prevents unau-
thorized use of your phone line, it is pos-
sible for other radio units operating on
similar frequencies within a certain area
to unintentionally intercept your conver-
sations and/or cause interference. This
possible lack of privacy can occur with
any cordless phone.
Lightning damage is not common. Neverthe-
less, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
FCC STATEMENT
The phone complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reason-
able protection against radio and TV interfer-
ence in a residential area. However, your
equipment might cause TV or radio interfer-
ence even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone com-
pany can temporarily discontinue your ser-
vice. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
Also, the phone company can make changes
to its lines, equipment, operations, or proce-
dures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interrup-
tion of your telephone service.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
Consult your local RadioShack store if the
problem still exists.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 5 Tuesday, September 12, 2000 3:12 PM
these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed,
sofa, rug, or other similar surface. This
product should never be placed near or
over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, ba-
sic safety precautions should always be fol-
lowed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power com-
pany.
3. Never install telephone wiring during a
lightning storm.
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the net-
work interface.
14. Do not overload wall outlets and exten-
sion cords as this can result in a risk of
fire or electric shock.
6. Use caution when installing or modifying
telephone lines.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
7. Do not fix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid clean-
ers or aerosol cleaners. Use a damp
cloth for cleaning.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltage or other risks. Incor-
rect reassembly can cause electric
shock when the product is subsequently
used.
9. Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
17. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following condi-
tions:
11. Slots and openings in the cabinet and
the back or bottom are provided for ven-
tilation. To protect it from overheating,
• When the power cord plug is damaged
or frayed.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 6 Tuesday, September 12, 2000 3:12 PM
• If liquid has been spilled into the prod-
uct.
1. Use only the appropriate type and size
of battery pack specified in the instruc-
tion manual provided for this product.
• If the product has been exposed to rain
or water.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are cov-
ered by the operating instructions
because improper adjustment of other
controls may result in damage and will
often require extensive work by a quali-
fied technician to restore the product to
normal operation.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
4. Exercise care in handling the battery
pack in order not to short it with conduct-
ing materials such as rings, bracelets,
and keys. The battery or conductor may
overheat and cause burns.
• If the product has been dropped or the
cabinet has been damaged.
• If the product exhibits a distinct change
in performance.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
19. Do not use the telephone to report a gas
leak in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
SAVE THESE
INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW
.
THESE INSTRUCTIONS
ˆ Features
Your Sprint 2.4 GHz Digital Spread Spec-
trum Dual Keypad Cordless Phone uses ad-
vanced technology to give you superior
audio quality and extended range.
as provided by your local phone company to
Caller ID service subscribers. If you sub-
scribe to Call Waiting with Caller ID, the
phone can show you the incoming caller in-
formation, even when you are already talking
on the phone.
The phone's Caller ID records each caller's
telephone number (and name, if available in
your area) and the date and time of the call,
6
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 7 Tuesday, September 12, 2000 3:12 PM
Facedown or Faceup Handset Charging
— you can place the handset on the base
face down or face up (to show the Caller ID
display, for example).
Your phone has these features:
2.4 GHz Operation
— provides longer range
and less interference than many other cord-
less phones.
30 Channels
channel when you make or answer a call.
— automatically selects a clear
Spread Spectrum Technology
the signal across several frequencies for
added security during phone conversations.
— spreads
Headset Jack
— lets you connect an option-
al headset (available from your local
RadioShack store) for hands-free conve-
nience.
Lighted Keypad
any key or receive a call, making the phone
easy to use, even in total darkness.
— lights when you press
Auto Talk
— lets you set the phone so you
Caller ID Memory
ID records.
— stores up to 50 Caller
can answer a call simply by lifting the hand-
set from the base or by pressing any key
when the handset is away from the base.
Dual Keypads
— a full set of keys on both
the handset and base let you use either key-
pad to operate the phone.
Ample Talk and Standby Time
— the sup-
plied battery (when fully charged) provides
about 7 hours of talk time or 7 days of stand-
by time.
Speakerphone
— lets you make or answer
calls without using the handset.
Security Access-Protection Code
— auto-
Network Service
calling features Return Call, Repeat Dial, and
Cancel Call Waiting.
— supports the advanced
matically prevents other cordless phone us-
ers from using your phone line while the
handset is off the base.
3-Line Liquid Crystal Display with Back-
Adjustable Ringers
volumes for the handset and base ringer’s.
— you can set different
light
— lets you view an entire Caller ID
record on one screen.
Redial
— lets you quickly redial any of the
Two-Way Intercom/Paging System
— lets
last three numbers dialed on the handset
and the last number dialed on the base.
you send a signal from the base to the hand-
set (or from the handset to the base) to page
someone or locate the handset when it is
away from the base. If someone answers at
the other end, you can use the phone as an
intercom.
Flash
— sends an electronic switchhook sig-
nal for use with special phone services, such
as Call Waiting.
Tone/Pulse Dialing
— lets you use your
30-Number Memory Dialing
— lets you
phone with either type of service and you can
quickly switch from pulse to tone dialing for
long-distance, bank-by-phone, or other spe-
cial services.
store up to 30 numbers (20 in the handset
and 10 in the base) in memory for easy dial-
ing.
Volume Control
volume you hear through the handset.
— lets you adjust the
Hearing-Aid Compatibility
the phone with hearing aids that have a T
(telephone) switch.
— lets you use
7
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 8 Tuesday, September 12, 2000 3:12 PM
ˆ Installation
jacks and adapters available at your local
RadioShack store, or have the telephone
company update the wiring for you.
MOUNTING THE PHONE
You can place the phone on a desk or table,
or mount it on a standard wall plate or direct-
ly on a wall. Select a location that is:
The USOC number of the jack to be installed
is RJ11C (or RJ11W for a wall plate jack).
• near an AC outlet
On a Desk, Shelf, or Table
• near a telephone line jack
• out of the way of normal activities
Follow these steps when you place the base
on a desk, shelf or table.
• away from electrical machinery, electri-
cal appliances, metal walls or filing cabi-
nets, wireless intercoms, alarms, and
room monitors
1. Insert the bracket’s tabs into the base’s
upper tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
• away from other cordless phones
2. Plug one end of the supplied long modu-
TEL LINE
lar cord into the
back of the base.
jack on the
The base's location affects the handset's
range. If you have a choice of several loca-
tions, try each to see which provides the best
performance.
3. Route the modular cord through the
strain relief hook.
Cautions:
You must use a Class 2 power
source that supplies 9V AC
and delivers at least 350 mA.
Its center tip must be set to positive and
!
DC IN 9V
4. Plug the modular cord's other end into a
modular telephone line jack.
its plug must fit the phone's
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
5. Insert the supplied AC adapter's barrel
DC IN 9V
plug into the
the base.
jack on the back of
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you dis-
connect it from the phone.
6. Route the adapter's cord through the
strain relief slot on the bracket.
7. Plug the adapter into a standard AC out-
let.
Note:
Your telephone connects directly to a
modular telephone line jack. If your tele-
phone wiring does not have a modular jack,
you can update the wiring yourself using
8. Lift the base's antenna to a vertical posi-
tion.
8
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 9 Tuesday, September 12, 2000 3:12 PM
Note:
To mount the phone directly on a wall,
On a Wall Plate or Wall
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base (minimum length 13/8
inches.
1. Insert the bracket’s tabs into the base’s
lower tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
Follow the steps under “On a Wall Plate or
Wall,” then apply these additional instruc-
tions for placement on a wall.
2. Plug one end of the supplied short mod-
TEL LINE
ular cord into the
back of the base.
jack on the
1. Drill two holes 315/16
3
/16"
3. Insert the supplied AC adapter's barrel
inches (100 mm) apart.
DC IN 9V
plug into
base.
jack on the back of the
Then thread a screw into
each hole, letting the
15
3 /16"
heads extend about 3/16
inch (5 mm) from the wall.
4. Route the adapter and modular cords
through the grooves on the bracket.
2. Plug one end of the sup-
plied long modular cord
TEL LINE
into the
jack on the back of the
base and route the adapter cable and
modular cords through the grooves on
the bracket.
3. Align the bracket's keyhole slots with the
mounting screws and slide the base
downward to secure it.
5. Plug the modular
cord's other end
into the wall plate
jack, then align the
bracket's keyhole
slots with the wall
plate studs and
slide the base downward to secure it.
6. Plug the adapter into a standard AC out-
let.
7. Press and lift out the handset holder.
Rotate it 180°, then snap it back into
place so it holds the handset.
CONNECTING, CHARGING
AND REPLACING THE
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack in the hand-
set. Before using your phone, you must
connect the battery pack, then charge it for
about 24 hours.
8. Lift the base's antenna to a vertical posi-
tion.
9
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 10 Tuesday, September 12, 2000 3:12 PM
1. Press down and slide off the battery
pack compartment cover.
code, return the handset to the base for
about 5 seconds.
• Using a pencil eraser, clean the charg-
ing contacts on the handset and base
about once a month.
• If the battery pack becomes weak during
a call, the handset beeps every 3 sec-
onds and LowBatteryflashes. When
this happens, you cannot make a call
until you recharge the battery pack.
2. Lift the battery pack out of the compart-
ment.
3. Plug the bat-
tery pack's con-
• About once a month, fully discharge the
battery by keeping the handset off the
base until LowBatteryflashes. Oth-
erwise, the battery pack loses its ability
to fully recharge.
nector into the
socket in the
compartment,
(the connector
fits only one
way), replace the battery pack, and
replace the cover.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
To charge the battery pack, place the hand-
set either faceup or facedown on the base.
The CHARGE/IN USE indicator on the base
lights and Total:00appears.
• If you are not going to use your phone
for an extended period of time, discon-
nect the battery pack. This increases the
battery pack's usable life.
Note:
Be sure the battery is properly con-
nected before you try to charge it. The
CHARGE/IN USE indicator flashes when the
handset is on the base with the battery not
connected.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an over-
night charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
Recharge the battery pack when LowBat-
teryflashes.
Notes:
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
TALK
hear a beep when you press
.
Warning:
Dispose of the old battery pack
Return the handset to the base for about
5 seconds to reset the security access-
protection code.
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 6
for additional information on proper battery
handling).
• If the base loses power for 60 minutes
while the handset is away from it or the
the handset’s battery pack is completely
discharged, the security access-protec-
tion code might be lost. To reset the
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
10
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 11 Tuesday, September 12, 2000 3:12 PM
Important:
The EPA certified
teries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-843-
7422) for information on Ni-Cd battery recy-
cling and disposal bans/restrictions in your
area. RadioShack’s involvement in this pro-
gram is part of the company’s commitment to
preserving our environment and conserving
our natural resources.
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a con-
venient alternative to placing used Ni-Cd bat-
A QUICK LOOK AT THE HANDSET
Note:
The handset window has plastic film on it to protect it during shipment. Carefully peel off
the film before using your phone for the first time.
Use MEM to store or re-
call names and numbers
inmemory(see “Memory
Dialing” on Page 16).
Use VOL/CID
/
to adjust the handset
8 9
volume (see “Adjusting the Handset
Volume” on Page 14), set the ringer/
tone volume (see “Setting the Ringer
Tone/Volume” on Page 12), view Caller
ID records (see “Caller ID Operation” on
Page 19), or select options.
Use FLASH to select
the phone's flash
function (see “Using
Flash” on Page 15).
Use TALK to make a
call (see“Making and
Receiving Calls” on
Page 13).
Use CID to review Caller
ID records.
Press
/TONE to use your
phone company's special
tone services when you are
on a pulse line (see “Using
Tone Services on a Pulse
Line” on Page 15).
Use INTCM/DEL to page someone
at the base or transfer a call to the
base (see “Using Page/Intercom”
on Page 15), locate the handset, or
to erase information if you make a
mistake.
Use RDL/PAUSE to redial
one of the last three numbers
dialed (see“Using Redial” on
Page 14) or store a pause in a
number (see “Entering a
Pause” on Page 17).
Use SELECT/CHANNEL to se-
lect the phone's channels (see
“Selecting the Channel” on
Page 14), and other options.
Use MENU to activate the
phone company's network
services (see “Using the
PhoneCompany’s Network
Service” on Page 21).
11
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 12 Tuesday, September 12, 2000 3:12 PM
RING
To set the base’s ringer volume, set
SETTING THE DIALING
MODE
VOL
OFF LO
on the back of the base to
,
, or
HI
.
PULSE-TONE
Set
on the back of the base for
Note:
RING VOL
OFF
When you set
to
, the
the type of service you have. If you are not
sure which type you have, do this test after
you charge the handset's battery pack.
base (and the handset if it is on the base)
does not ring but other phones connected to
the same phone line rings. If the handset is
away from the base, it also rings.
PULSE-TONE
TONE
.
1. Set
to
TALK
2. Lift the handset and press
, or
TURNING AUTO TALK ON/
OFF
SPEAKER.
press
Listen for a dial tone.
3. Press any number other than 0.
Note:
Your phone is preset so you must press
TALK
when you lift the handset from the base
If your phone system requires that
to answer a call. With auto talk turned on,
you can answer a call by just lifting the hand-
set from the base. If the handset is away
from the base, you can answer by pressing
any key.
you dial an access code (9, for example)
before you dial an outside number, do
not press the access code, either.
If the dial tone stops, you have touch-
PULSE-TONE
tone service. Leave
set to
Follow these steps to turn auto talk on or off.
TONE
.
CID
1. Lift the handset and hold down
. A
If the dial tone continues, you have
menu appears with Auto Talk
PULSE-TONE
pulse service. Set
set to
selected.
PULSE
.
SELECT/CHANNEL
2. Press
to change the
TALK
4. Press
or place the handset on the
auto talk setting. Onor Offappears.
base to hang up.
3. Return the handset to the base or press
SETTING THE RINGER
TONE/VOLUME
CID
to store the new setting.
Note:
When auto talk is set to off, the hand-
You can select one of four different ringer
tone/volume settings on the handset. Re-
set continues to ring after you lift the handset
TALK
from the base until you press
.
VOL/CID 8
9
peatedly press
or
(except
during a call) to select the desired ringer set-
ting. Each time you press a button, the
phone rings at the selected setting and
RingerAHigh, RingerALow, Ring-
erBHigh, or RingerBLowappears.
TURNING CALLER ID/CALL
WAITING ON/OFF
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Call-
er ID information for an incoming call even
while you are using the phone.
Note:
VOL/CID 8
Pressing
at Ringer A
at Ringer B Low
VOL/CID 9
High or
does not change the setting. Press the oppo-
site arrow key to change the setting.
Follow these steps to turn the Caller ID/Call
Waiting feature on or off.
CID
1. Lift the handset and hold down
.
12
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 13 Tuesday, September 12, 2000 3:12 PM
2
VOL/CID 9
2. Press or
to select CIDCW
Follow these steps to store your area code.
(Caller ID/Call Waiting).
CID
1. Lift the handset and hold down
.
SELECT/CHANNEL
3. Press
to change the
3
VOL/CID 9
twice to select
2. Press or
Caller ID/Call Waiting setting. On or
Offappears.
AreaCode.
SELECT/CHANNEL
3. Press
,
then enter
4. Return the handset to the base to store
the new setting.
your three-digit area code. If you make a
mistake, repeatedly press 6 or 7 to
move the cursor over the incorrect digit,
then enter the correct number.
STORING YOUR AREA
CODE
Note:
If an area code is already stored,
You can store your local area code in the
phone's Caller ID record so it does not show
the area code if the received call is from your
local area. If for some reason you need to
dial the area code (or store it in the memory),
you can add it afterwards. See “Adding/De-
leting the Area Code” on Page 20.
it appears on the display. To delete the
INTCM/DEL
area code, press
three times
INTCM/DEL
or hold down
, then enter
your. area code. You can use 6 or 7
to move the cursor and edit the area
code.
SELECT/CHANNEL
4. Press
to store the
or return the
Note:
If your calling area requires 10-digit di-
CID
area code, then press
aling including area code, do not enter the
area code but leave this option blank.
handset to the base to clear the display.
ˆ Telephone Operation
INTCM/DEL
If you make a mistake, press
until
MAKING AND RECEIVING
CALLS
the incorrect entry is erased, then enter the
correct number. To delete the entire number,
INTCM/DEL
hold down
for at least 1 second.
To make a call, lift the handset and press
TALK
. Talkand the current volume setting
When you receive a call, IncomingCall
appears. To answer it, lift the handset from
(see “Adjusting the Handset Volume” on
Page 14) appear, and the CHARGE/IN USE
indicator on the base lights. Then dial the
number. The number appears as you dial,
then (after a few seconds) the call's elapsed
time appears.
TALK
the base and press
. If auto talk is on,
just lift the handset from the base. If the
handset is away from the base, press any
key. Talk and the current volume setting
appear.
You can also dial the number then press
To end a call, place the handset on the base
TALK
. Talkand the current volume setting
TALK
or press
.
appear, and the CHARGE/IN USE indicator
on the base lights. The number you entered
and the call’s elapsed time appear.
13
Telephone Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 14 Tuesday, September 12, 2000 3:12 PM
To switch to the handset while you are using
the speakerphone, simply lift the handset off
the base. If the handset is away from the
SELECTING THE CHANNEL
The phone has 30 channels. If the call
seems to disconnect for no reason during a
TALK
SPEAKER
.
base, press
, then press
SELECT/CHANNEL
call, press
on the handset
to select a different channel. Scanningap-
pears while your phone searches for a clear
channel.
Using Both the Handset and
Speakerphone
If someone else is using the speakerphone,
TALK
press
versation.
on the handset to join the con-
ADJUSTING THE HANDSET
VOLUME
If someone else is using the handset, press
To adjust the handset’s volume during a call,
SPEAKER
on the base to join the conversa-
VOL/CID 8
9
press
or
until you reach the
tion.
desired volume level. Volume Maximum,
Volume High, Volume Medium, or
VolumeLowappears.
During the call, one person can hang up and
let the call continue at the other keypad.
The setting is maintained even after you
hang up the phone.
Or, both people can hang up at the same
time to end the call.
Note:
VOL/CID 8
while the
When you press
Note:
If you hear a high-pitched noise from
volume is maximum or 9 while the volume
is low, the setting does not change and the
phone beeps three times.
the base's speaker, the handset and the
base are too close together.
USING REDIAL
USING THE
SPEAKERPHONE
You can quickly dial any of the last three
numbers you dialed on the handset. Lift the
handset and repeatedly press
until the number you want to dial appears.
To make or answer a call using the speaker-
RDL/PAUSE
SPEAKER
phone, press
. The SPEAKER indi-
cator lights. When you hear a dial tone, dial
the number.
TALK
Then press
number.
and the phone dials the
To set the speakerphone's volume, slide
You can also dial the last number dialed us-
VOLUME
on the right side of the base.
SPEAKER
ing the speakerphone. Press
then
REDIAL/PAUSE
on the base.
SPEAKER
To end a speakerphone call, press
again.
Notes:
Switching Between the Handset
and Speakerphone
• The redial memory for each keypad is
separate. You cannot redial a number
you dialed on the handset’s keypad
To switch to the speakerphone while you are
REDIAL/PAUSE
using
on the base’s key-
SPEAKER
using the handset, press
on the
pad, and vice versa.
base. When you hear the conversation or
TALK
dial tone on the speakerphone, press
on the handset.
14
Telephone Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 15 Tuesday, September 12, 2000 3:12 PM
RDL/PAUSE
• On the handset, press
after
USING PAGE/INTERCOM
TALK
pressing
dialed.
to dial the last number
You can use the phone as a two-way pager
and intercom between the base and the
handset. This is useful if the handset is away
from the base and you want to locate it, or if
you want to have a conversation between
someone with the handset and someone at
the base.
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 17.
IN-
To page the base from the handset, press
TCM/DEL
. Paging Base appears, and the
SPEAKER
base and handset ring. Press
or
USING FLASH
INTCM/PAGE
on the base to answer the
FLASH
performs the electronic equivalent of
page. Intercomappears.
a switchhook operation for special services,
such as Call Waiting.
IN-
To page the handset from the base, press
TCM/PAGE
. The handset and base ring, and
TALK
INTCM/DEL
or
For example, if you have Call Waiting, press Pagingappears. Press
FLASH
to answer an incoming call without
on the handset to answer the page. Inter-
FLASH
disconnecting the current call. Press
again to return to the first call.
comappears.
TALK
To end an intercom call, press
on the
SPEAKER
on the base, or
Note:
services, pressing
the current call.
If you do not have any special phone
handset, press
hang up the handset.
FLASH
might disconnect
If a call comes in during an intercom conver-
sation, either the person at the base or the
person at the handset can answer the call.
USING TONE SERVICES ON
A PULSE LINE
TALK
SPEAKER
on
Press
on the handset or
the base once to end the intercom call, then
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
TALK
SPEAKER
again to answer the
press
or
incoming call.
Note:
The intercom does not operate if the
party being paged is already on a call.
PULSE-TONE
PULSE
.
1. Be sure
is set to
2. Dial the service's main number.
Transferring a Call between the
Handset and Base
3. When the service answers, press
/
TONE
. Any additional numbers you dial
You can use the phone's intercom feature to
transfer a call between the handset and the
base.
are sent as tone signals.
When you hang up, the phone automatically
resets to pulse dialing.
To transfer a call from the handset to the
INTCM/DEL
base, press
. The call is placed on
hold, and PagingBaseand Holdappear.
15
Telephone Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 16 Tuesday, September 12, 2000 3:12 PM
SELECT/CHAN-
4. To store a name, press
When the person at the base answers, press
TALK
NEL
. StoreNameappears.
. The call is released from hold and
transferred to the base.
If you do not want to enter a name, skip
to Step 6.
To transfer a call from the base to the hand-
INTCM/PAGE
set, press
. The call is put on
VOL/CID 8
9 to select the characters and 6 or 7
5. To enter a name, press
or
hold, and Pagingand Holdappear. When
the person with the handset answers, press
to move the cursor.
SPEAKER
. The call is released from hold and
transferred to the handset.
VOL/CID 9
Repeatedly press
to view
the characters in alphabetical order.
(The display shows uppercase letters
first, then lowercase letters, numbers,
and special characters.)
MEMORY DIALING
You can store up to 30 phone numbers in
memory (20 in the handset’s and 10 in the
base’s memory), then dial a stored number
by entering its memory location number.
Notes:
VOL/CID 8
ters in reverse alphabetical order.
• Press
to see the charac-
You can also store a name with each number
in the handset’s memory.
VOL/CID 8
to scroll rapidly through the charac-
ters.
9
• You can hold down
or
Use the supplied memory sticker to record
the numbers you stored in the base’s memo-
ry. Peel the backing from the sticker and at-
tach the sticker to the base.
• If you make a mistake, move the cur-
sor over the error, then enter the cor-
INTCM/DEL
rect character, or press
to
Storing a Number in the Handset's
Memory
delete a character. To delete all the
INTCM/DEL
characters, hold down
at least 1 second.
for
Notes:
SELECT/CHANNEL
6. Press
. StoreNum-
• The phone beeps five times exits the
storing process if you wait more than 20
seconds between each keypress.
berappears.
7. Enter the phone number and any tone or
pause entries (see “Using Tone Services
on a Pulse Line” on Page 15 and “Enter-
ing a Pause” on Page 17).
• If you receive a call during memory
entry, the phone exits the storing pro-
cess.
SELECT/CHANNEL
8. Press
. The phone
1. Lift the handset.
beeps and Memory nn Stored
appear (nn is the location number you
selected). After 2 seconds, Memory
Store appears. Repeat Steps 3–8 to
store more numbers.
MEM
2. Hold down
until Memory Store
and a list of memory location numbers
appear.
(01-20
VOL/CID 8
or
3. Press a number
) or
9#to choose a two-digit memory loca-
tion. Precede a single digit location num-
ber with 0 — 01, 02, 03, and so on.
MEM
9. When you finish, press
.
16
Telephone Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 17 Tuesday, September 12, 2000 3:12 PM
To replace a stored number, store a new one
in its place.
2. Enter the number (up to 16 digits) and
any tone or pause entries (see “Using
Tone Services on a Pulse Line” on
Page 15 and “Entering a Pause”).
Editing or Deleting a Number in
the Handset’s Memory
Notes:
Follow these steps to edit or delete a memo-
ry number.
• The phone beeps five times and exits
the storing process if you enter more
than 16 digits.
1. Lift the handset.
• Each tone or pause entry uses one digit
of memory.
MEM
2. Hold down
until Memory Store
and a list of memory location numbers
appear.
MEMORY
3. Press
again, then enter the
0 9
memory location number ( – ) where
you want to store the phone number. A
long beep indicates that the number is
stored.
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
VOL/CID 8
9
.
pressing
or
SELECT/CHANNEL
4. Press
appears with the three options listed
VOL/CID 8
.
A
menu
To replace a number in the base's memory,
simply store a new number in its place. To
below. Press
or
9
to high-
MEMORY
erase a memory number, press
light the desired option then press
twice, then press the memory location num-
ber (0-9) you want to erase. A long tone indi-
cates that the number has been erased from
the memory location.
SELECT/CHANNEL
to choose it.
EditMemorynn- edit the record as
described in Steps 5 through 7 of “Edit-
ing or Deleting a Number in the Hand-
set’s Memory” on Page 17.
Entering a Pause
Delete Memory nn - the display
prompts you to confirm the deletion.
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an out-
side number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to con-
nect. To enter a 2-second pause in the hand-
VOL/CID 8
Yes, then press
Press
to move the cursor to
SELECT/CHANNEL
or
INTCM/DEL
.
The phone beeps, and
MemorynnDeletedappears.
Go Back - returns you to the list of
memory numbers.
RDL/PAUSE
set’s memory, press
. Pappears
if you are storing a number into the handset’s
memory. You can add more pause entries
for a longer pause.
Storing a Number in the Base's
Memory
To enter a 2-second pause when storing a
Note:
The phone beeps five times and exits
REDIAL/
number in the base’s memory, press
the storing process if you wait more than 20
seconds between each keypress.
PAUSE
.
MEMORY
1. Press
. The CHARGE/IN USE
indicator blinks.
17
Telephone Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 18 Tuesday, September 12, 2000 3:12 PM
Then, at the appropriate place in the call,
Reviewing the Handset's Memory
Numbers
MEM
MEMORY
on the base) and en-
press
(or
ter the number for the location where the ad-
ditional information is stored.
To review your handset's memory numbers,
MEM
press
. The list of memory location num-
bers (01–20) appears with the name stored
with each number (or <Memorynn>if you
did not store a name).
Testing Stored
Emergency Numbers
If you store an emergency service's number
(police department, fire department, ambu-
lance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
To see the stored phone numbers, select the
VOL/CID 8
location you want to see using
or
9 or enter the location number, then press
7. An arrow to the right of the number
means it is longer than 13 digits. Press 7
again to see the rest of the number. Repeat-
edly press 6 to return to the name display.
USING A HEADSET
MEM
To exit the memory number list, press
.
You can make or answer calls with hands-
free convenience using an optional headset
that has a /32 -inch (2.5-mm) plug. Contact
your local RadioShack store for a suitable
headset.
To see a stored name and phone number at
SELECT/CHANNEL
the same time, press
3
when the cursor is by a memory location
IN-
number. To exit this display, hold down
TCM/DEL
until the display clears.
To connect the headset, pull open the rubber
Dialing a Memory Number
cover marked
on the side of the handset,
then insert the headset's plug into the jack.
To dial a number stored in the handset’s
MEM
memory, lift the handset and press
. The
list of memory location numbers appears.
Choose a memory location (01–20) by press-
VOL/
ing a number or by repeatedly pressing
CID 8
9
or , then press
TALK
.
To dial a number stored in the base's memo-
Notes:
SPEAKER
ry, press
. When you hear a dial
MEMORY
tone, press
, then press the memory
• Connecting a headset disconnects the
handset's earpiece and microphone.
location number for the number you want to
dial.
VOL/CID 8
controls the headset's volume.
9
•
or
on the handset also
Note:
If you select an empty memory loca-
tion on the base, the base beeps 5 times.
• If you place the handset on the base to
recharge it while the headset is con-
nected, be sure the handset seats prop-
erly.
Chain-Dialing Service Numbers
For quick recall of numbers for special ser-
vices (such as bank-by-phone), store each
group of numbers in its own memory loca-
tion. Dial the service's main number first.
18
Telephone Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 19 Tuesday, September 12, 2000 3:12 PM
• You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for
greater convenience.
With a headset connected, you can make or
answer calls as usual using the speaker-
phone or keys on the handset.
When you finish using the headset, discon-
nect it from the handset and close the rubber
cover to protect the jack.
ˆ Caller ID Operation
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and sec-
ond rings of every call you receive.
VOL/CID 8
to scroll back
est to the oldest, or
through the records. To scroll quickly through
VOL/CID 8
the records, hold down
or
9
.
When you scroll past the last record, the total
record number appears, then the first record.
When you scroll past the first record, the total
record number appears, then the last record.
The phone displays this information after the
second ring, and it stores up to 50 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (see
“Caller ID Messages”).
The top line of each record shows the date,
time and the number of calls from that num-
ber. The second line shows the caller's
name, and the third line shows the caller's
phone number.
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the in-
To exit the Caller ID record display, press
CID
.
FLASH
coming call, press
. To resume the
FLASH
previous phone conversation, press
again.
Caller ID Messages
Display
Description
If the phone's Caller ID memory becomes
full, any new call replaces the oldest call's
record.
Shows the number of new
Caller ID records (records
you have not viewed) and
the total number of records.
NEW: XX
TOTAL: XX
REVIEWING CALLER ID
RECORDS
The caller has blocked the
Caller ID information.
Private
Name
If the handset is faceup on the base, it shows
the number of new Caller ID records, if any,
and the total number of records.
or
Private
Number
To review the contents of each Caller ID
CID
record, lift the handset and press
call the number of records on the display.
VOL/CID 9
to re-
Then, repeatedly press
to scroll
through the Caller ID records from the new-
19
Caller ID Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 20 Tuesday, September 12, 2000 3:12 PM
STORING A CALLER ID
RECORD TO MEMORY
Display
Description
The caller is not within a
Caller ID service area.
Unknown
Name
Follow these steps to store the name and
number from a Caller ID record into a memo-
ry location.
or
Unknown
Number
CID
VOL/CID 8
9
1. Press
then
or
to
Appears if there was an
error during the transmis-
sion of Caller ID informa-
tion. Occasional errors are
normal. If the phone fre-
quently displays Incom-
pleteData, contact
your local telephone com-
pany or RadioShack store.
Incomplete
Data
recall the record you want to store.
If you want to add or delete the area
3
code, press .
MEM
2. Press
. Select Location
appears.
01 20
) by
3. Choose a memory location (
–
pressing a number or by repeatedly
ADDING/DELETING THE
AREA CODE
VOL/CID 8
9
, then press-
pressing
or
.
SELECT/CHANNEL
ing
When the area code of the received call is
the same as the one you stored (see “Storing
Your Area Code” on Page 13), the caller ID
record does not show the area code. If it is
different, the record shows the area code.
However, you can add or delete the area
code on the display. When the record is on
If the selected location is empty, the
phone beeps to confirm that it stored the
number, then the Caller ID record
appears.
If a record exists in the selected loca-
tion, Replace Memory? appears,
prompting you to confirm the replace-
3
the display, press to add or delete the area
VOL/CID 8 9# #
or to move
ment. Press
3
code. Pressing again deletes or adds the
the cursor to Yes or No, then press
area code.
SELECT/CHANNEL
. The phone beeps to
confirm the replacement.
DIALING NUMBERS FROM A
CALLER ID RECORD
DELETING CALLER ID
RECORDS
To dial a local number stored in a Caller ID
TALK
record, recall the record, then press
. If
You can delete Caller ID records individually
or all at once.
1
it is a long distance call, press (1appears
before the displayed number) before you
TALK
press
. If you want to add or delete the
Follow these steps to delete a single Caller
ID record.
3
TALK
.
area code, press before you press
Note:
If a Caller ID record does not contain a
CID
VOL/CID 8
9
1. Press
then
or
to
phone number (if it was blocked by the caller,
for example) you cannot dial from that
record.
recall the record you want to delete.
INTCM/DEL
2. Press
. DeleteMessage?
and Yes/No appear with the cursor
pointing to Yes.
20
Caller ID Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 21 Tuesday, September 12, 2000 3:12 PM
SELECT/CHANNEL
INTCM/DEL
.
3. Press
or
Advanced Calling Services
The phone beeps once.
Feature
Description
Press
69
Follow these steps to delete all Caller ID
records.
Return Call The service retains the
number of the party that
called you last and
CID
1. Press
so the record totals appear.
automatically dials that
number. Return call is
useful if you miss an
INTCM/DEL
2. Press
. Delete All? and
Yes/Noappear with the cursor pointing
to No.
incoming call.
66
70
Repeat Dial When you get a busy
signal or you want to
redial the last number
you called, the service
continuously redials the
number until the call
VOL/CID 8
Yes, then press
3. Press
to move the cursor to
SELECT/CHANNEL
or
INTCM/DEL
. The phone beeps once and
Total:00appears.
goes through.
USING THE PHONE
COMPANY’S NETWORK
SERVICE
Cancel Call Temporarily cancels
Waiting
your Call Waiting ser-
vice. This is useful
when you also use your
telephone line for inter-
net service or sending/
receiving faxes. Enter
the key sequence prior
to dialing the internet or
fax number. Call Wait-
ing is restored when
you disconnect the call.
Your phone supports advanced calling ser-
vices provided by many phone companies
such as Return Call, Repeat Dial, or Cancel
Call Waiting.
To use these features, you must be in an
area where these services are available and
you must subscribe to these services
through your phone company. Contact your
local telephone company for more details on
how to subscribe.
Notes:
• When using certain calling features,
local, toll or long distance charges might
apply.
The phone has the following features prepro-
grammed in its memory.
Important:
Some phone companies use dif-
• You might not be able to use certain call-
ing features on some long distance calls
or from certain types of business lines.
ferent key sequences to activate the fea-
tures. If your phone company uses different
sequence, you must edit the sequence be-
fore using the service. See “Editing Ad-
vanced Service Names and Numbers.”
Follow these steps to access services.
1. Lift the handset.
MENU
2. Press
. ReturnCall, Repeat
Dial, and CancelCWappear.
VOL/CID 8
3. Press the number or
or
9
to select the service you want to use.
21
Caller ID Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 22 Tuesday, September 12, 2000 3:12 PM
TALK
SELECT/CHANNEL
. A menu listing
4. Press
. The selected service num-
4. Press
ber appears and is dialed.
Edit, Restore, and Go Back
VOL/CID 8
highlight the desired option then press
9
appears. Press
or
to
Note:
You can display the programmed ser-
vice number of each calling feature. At Step
2 above, press7 to view the number and 6
to return to the name display.
SELECT/CHANNEL
to choose it.
Edit — Service name appears.
Edit the service name and press
SELECT/CHANNEL
.
Then, Service
Editing Advanced Service Names
and Numbers
numberappears. Edit the number and
SELECT/CHANNEL
press
.
Enter the
name and number as described in Steps
5 through 8 of “Storing a Number in the
Handset's Memory” on Page 16.
You might need to change the number
stored in any of the three service locations,
for example, if your phone company uses dif-
ferent number sequences from the pro-
grammed ones.
Restore — prompts you to confirm
the restoration. If you want to return to a
preprogrammed calling feature, press
Follow these steps to edit a key sequence.
1. Lift the handset.
VOL/CID 8
then press
to move the cursor to Yes,
SELECT/CHANNEL
.
The
phone beeps, and ServiceSetting
Restoredappears.
MENU
2. Hold down
until Select to
Edit and a list of calling features
Go Back — returns you to the list of
appears.
service numbers.
3. Choose a calling feature by pressing a
1 3
VOL/CID 8
9
.
number ( – ) or
or
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
Suggestion
The phone does not work prop- Be sure the base's phone line cord and AC adapter are correctly and
erly.
securely connected.
Be sure the battery pack in the handset is connected and charged.
Return the handset to the base for about 5 seconds to reset the secu-
rity access-protection code.
The display flashes slowly
when the handset is faceup on
the base.
Make sure the battery pack in the handset is properly connected.
22
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 23 Tuesday, September 12, 2000 3:12 PM
Problem
Suggestion
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Lift the base's antenna to a fully vertical position.
Be sure the handset's battery pack is charged. (If the battery pack
power is too low, the handset cannot display LowBattery.)
Low volume or unusual
sounds.
Someone has picked up another phone on the same line. Hang up the
other phone.
Dropout or mute.
Keep the handset away from computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent
lights, and electrical appliances. Move to another location or turn off
the source of interference.
SELECT/CHANNEL
Press
to change the channel.
Hang up and redial the number.
The phone cannot be operated Lift the base's antenna to a vertical position.
at a useful distance from the
Be sure neither the handset's nor base's antenna is touching a metal
surface.
base because the signal
becomes weak or noisy (hand-
set's range has decreased).
Return the handset to the base and recharge the battery pack.
The handset battery pack does Check the charging contacts on the handset and base. If they are dirty,
not charge.
clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Connecting, Charging and Replacing
the Battery Pack” on Page 9).
The handset does not ring or
receive a page.
Move the handset closer to the base.
Lift the base's antenna to a vertical position.
Be sure the battery pack in the handset is connected and charged.
Move the base away from other electrical devices.
You have an incoming call, but Let the phone ring twice before you answer so the phone has time to
do not receive any Caller ID
information.
record the Caller ID information.
Check that the phone is correctly and securely connected.
Check with your phone company to verify that your Caller ID service is
active.
If you still have problems, disconnect the phone. If other phones on the same line work proper-
ly, the fault is in this phone or its installation. If you cannot find the problem, take the phone to
your local RadioShack store for assistance.
• Keep the phone dry. If it gets wet, wipe it
dry immediately.
CARE
To enjoy your Sprint 2.4GHz Digital Spread
Spectrum Cordless Telephone for a long
time:
• Use and store the phone only in normal
temperature environments.
23
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5522.fm Page 24 Tuesday, September 12, 2000 3:12 PM
• Handle the phone gently and carefully. Do not drop it.
• Keep the phone away from dust and dirt.
• Wipe the phone with a damp cloth occasionally to keep it looking new.
Modifying or tampering with the phone’s internal components can cause a malfunction and
might invalidate its warranty and void your FCC authorization to operate it. If your phone is not
performing as it should, take it to your local RadioShack store for assistance. If the trouble is
affecting the telephone lines, the phone company can ask you to disconnect your phone until
you have resolved the problem.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-5522
UCZZ01695BZ
09A00
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
Download from Www.Somanuals.com. All Manuals Search And Download.
|