EL 3
EL 5
Elliptical
Elliptical
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS ON YOUR
NEW ELLIPTICAL AND WELCOME
TO THE SPIRIT FAMILY!
Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc.
Your new elliptical was manufactured by one of the leading fitness manufacturers in the
world and is backed by one of the most comprehensive warranties available. Through
your dealer, Spirit will do all we can to make your ownership experience as pleasant as
possible for many years to come. The local dealership where you purchased this
elliptical is your administrator for all Spirit warranty and service needs. Their
responsibility is to provide you with the technical knowledge and service personnel to
make your experience more informed and any difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone
number, and the date of purchase below to make any future, needed contact easy. We
appreciate your support and we will always remember that you are the reason that we
are in business. Please complete and mail your registration card today and enjoy your
new elliptical.
Yours in Health,
Spirit Manufacturing, Inc.
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
Product Registration
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
EL3 / EL5 Ver. A
2
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING - Read all instructions before using this appliance.
Ŷ
Ŷ
Do not operate the elliptical on deeply padded, plush or shag carpet. Damage to both the
carpet and elliptical may result. Set the elliptical up on a hard, even surface.
Keep children away from the elliptical. There are obvious pinch points and other
caution areas that can cause harm.
Ŷ
Ŷ
Keep hands away from all moving parts.
Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working
properly, call your dealer.
Ŷ
Ŷ
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
Ŷ
Ŷ
Never drop or insert any object into any openings.
Do not use outdoors.
ŶTo disconnect, turn all controls to the off position, then remove the plug from the outlet.
ŶDo not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
ŶThe hand pulse sensors are not medical devices. Various factors, including the user¶s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Ŷ
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
3
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Electrical Information
WARNING!
ƔNEVER remove any cover without first disconnecting AC power supply.
Ɣ
If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may
be affected. Such conditions are not covered under your warranty. If you suspect the
voltage is low, contact your local power company or a licensed electrician for proper testing.
ƔNEVER expose this
to rain or moisture. This product is NOT designed for
Use outdoors, near a pool or spa, or in any other high humidity environment.
elliptical
Important Operation Instructions
ƔNEVER operate this elliptical without reading and completely understanding the results of
any operational change you request from the computer.
Ɣ
Understand that changes in resistance do not occur immediately. Set your desired level on
the computer console and release the adjustment key. The computer will obey the
command gradually.
Ɣ
NEVER use your elliptical during an electrical storm. Surges may occur in your household
power supply that could damage elliptical components.
ƔUse caution while participating in other activities while using your elliptical such as watching
television, reading, etc. These distractions may cause you to lose balance, which may result
in serious injury.
ƔAlways hold on to a handrail or hand bar while making control changes.
Do not use excessive pressure on console control keys. They are precision set to properly
function with little finger pressure. Pushing harder is not going to make the unit go faster or
slower. If you feel the buttons are not functioning properly with normal pressure, contact your
Spirit dealer.
4
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Pack Check List (EL3)
Step 1
3/8" x 19 x 1.5T
3/8" x 23 x 2T
Flat Washer (2pcs)
Curved Washer (4pcs)
M5 x 15m/m
Phillips Head Screw (6pcs)
3/8" x 2-1/4"
Hex Head Bolt (2pcs)
3/8" x 3-3/4"
Hex Head Bolt (4pcs)
Step 2
3/8"x2T
Split Washer (1pc)
M5x12m/m
Phillips Head Screw (4 pcs)
3/8"x23x2T
Curved Washer (2pcs)
3/8" x 3/4"
Hex Head Bolt (2pcs)
3/8" x 2-1/4"
Hex Head Bolt (1pc)
5
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
3/8" x 35 x 2.0T
Flat Washer (2 pcs)
ȥ
25
Wave Washer (2 pcs)
ȥ
3.5x12m/m
Self Tapping Screw (6 pcs)
3/8" x 5/8"
Hex Head Bolt (2 pcs)
Step 4
M5x10m/m
Phillips Head Screw (4 pcs)
ȥ
3.5x12m/m
Self Tapping Screw (2pcs)
M5 x 15m/m
Phillips Head Screw (4pcs)
5/16" x 7T
Nylon Nut (2 pcs)
5/16" x 18x 1.5T Flat
Washer (2 pcs)
5/16´ x 1-1/4´
Hex Head Bolt (2 pcs)
6
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools
Phillips Head Screw Driver (1 pc)
Short Screw Driver (1 pc)
12m/m Wrench ( 2pcs)
13/14m/m Wrench ( 1pc)
7
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Pack Check List (EL5)
Step 1
3/8" x 23 x 2T
Curved Washer (4pcs)
3/8" x 19 x 1.5T
Flat Washer (2pcs)
3/8" x 2-1/4"
Hex Head Bolt (2pcs)
M5 x 15m/m
Phillips Head Screw (6pcs)
3/8" x 3-3/4"
Hex Head Bolt (4pcs)
Step 2
M5 x 12m/m
Phillips Head Screw (4pcs)
3/8" x 2T
Split Washer (1pc)
3/8" x 23 x 2T
Curved Washer (2pcs)
3/8´ x 2-1/4´
Hex Head Bolt (1pc)
3/8" x 3/4"
Hex Head Bolt (2pcs)
8
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
ȥ
25
3/8" x 35 x 2.0T
Flat Washer (2 pcs)
Wave Washer (2 pcs)
ȥ
3.5x12m/m
Self Tapping Screw (6 pcs)
3/8" x 5/8"
Hex Head Screw (2 pcs)
Step 4
M5x10m/m
Phillips Head Screw (4 pcs)
ȥ
3.5x12m/m
Self Tapping Screw (2pcs)
M5 x 15m/m
Phillips Head Screw (4pcs)
5/16" x 7T
Nylon Nut (2 pcs)
5/16" x 18x 1.5T
Flat Washer (2 pcs)
5/16´ x 1-1/4´
Hex Head Bolt (2 pcs)
9
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools
Phillips Head Screw Driver (1 pc)
Short Screw Driver (1 pc)
12m/m Wrench (2pcs)
13/14m/m Wrench (1pc)
10
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Ŷ
UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion.
STEP 1: REAR RAIL ASSEMBLY
1. Remove the hardware from the hardware pack for step 1. You should have four 3-3/4´
X 3/8´ bolts, four curved washers, two 2-1/4´ X 3/8´ bolts, two flat washers and six 5/8´
X 1/4´ Phillips head screws.
2. Put the two flat washers on the 2-1/4´ bolts and hand-tighten them, through the top of
the middle stabilizer tube, into the rear rail assembly.
3. Put the four curved washers on the 3-3/4´ bolts and hand-tighten them through the
front of the middle stabilizer tube, into the rear rail assembly.
4. Using the wrench provided tighten all six bolts securely.
5. Locate the four plastic covers (XE150, XE350 only) for the rear rail assembly and the
one cover for the front stabilizer and install them using the six 5/8´ X 1/4³ screws and
the Phillips head screw driver provided.
STEP 2: CONSOLE MAST ASSEMBLY
1. Remove the hardware from the hardware pack for step 2. You should have one 2-1/4´ X
3/8´ bolt, one lock washer, two 3/4´ X 3/8´ bolts, two curved washers and four 1/2´ X
1/4´ Phillips head screws.
2. Locate the console mast and console mast cover and slide the cover onto the mast as
far as it will go. Make sure the cover is facing the correct way.
3. At the top opening of the main body of the elliptical is a wire harness. Unravel and
straighten out the wire harness and feed it into the bottom of the console mast tube and
out of the top opening.
4. Install the console mast into the receiving bracket in the top of the main body. NOTE:
there is one bolt already installed in the receiving bracket that will engage with the slot
at the bottom of the console mast. This needs to be tightened at the end along with the
three other console mast bolts.
11
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Put the flat washer onto the 2-1/4´ bolt and the two curved washers onto the two
3/4´ bolts. Install, and hand tighten, the 2-1/4´ bolt through the left side of the receiving
tube into the console mast. NOTE: There is a wire running through the tube. Be careful
not to damage or pinch this wire during this procedure. Damage to the electronic
console could result. Install, and hand tighten, the two 1´ bolts through the front of the
receiving tube into the console mast.
6. Using the two sided wrench tighten the three bolts, and the fourth bolt which is
pre-installed, firmly. These bolts should be tightened as much as you possibly can.
7. Locate the electronic console and the four 1/2´ X 1/4´ Phillips head screws.
8. There will be three electrical wire connectors at the top opening of the console mast,
two 2 pin (hand pulse sensors), one 10 pin (main wire harness). Connect these to the
mating connectors on the back of the console. The connectors are keyed so you cannot
plug them in the wrong way so do not force them.
9. Storing the excess wire back into the console mast, carefully install the console onto the
mounting plate and secure using the four Phillips head screws.
STEP 3: HANDLE BAR ASSEMBLY
1. Remove the hardware from the hardware pack for step 3. You should have two 5/8´ X
3/8´ bolts, two large flat washers, two large wave washers and six self tapping Phillips
head screws.
2. Locate and install the two large wave washers onto the handle bar axle, one on each
side.
3. Slide the left and right handle bars onto the appropriate side of the axle. There is a
sticker on each handle bar indicating L for left and R for right.
4. Put the large flat washers onto the two 5/8´ X 3/8´ bolts and install, and tighten, in the
threaded holes in the ends of the axle.
5. Install the plastic covers over the handle bar/axle connections with the six self tapping
Phillips head screws.
STEP 4: FOOT PAD/CONNECTING ARM ASSEMBLY (This step may have already been
performed at the factory on your unit)
1. Remove the hardware from the hardware pack for step 4. You should have two 1-1/4´ X
5/16´ bolts, two flat washers, two Nylon nuts, four 5/8´ machine screws (long), four 3/8´
machine screws (short) and two self-tapping Phillips head screws.
2. On the pedal arms, in the middle on top, there are two axles already installed in the
bushing housings. Remove, from one side of each axle, the bolt (one should be loose)
and washer. Remove the axle and set aside for the next step.
3. Locate the left foot pad/connecting arm. Holding the rear of the foot pad with your right
hand and the connecting arm, just in front of the foot pad, with your left hand, place the
foot pad over the bushing housing.
12
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Holding the axle (removed in step 2) in one hand, and the foot pad in the other, line up
the large hole in the side of the bracket (under the foot pad) with the hole in the bushing
housing and insert the axle all the way until the washer is flush against the bracket. You
may have to wiggle the axle while moving the footpad slightly to get the axle to go in.
5. Take the bolt that you removed from the axle in step 2 AND INSTALL THE NEW
ANTI-ROTATION BRACKET, then thread it into the hole in the axle. Tighten the bolt
using two wrenches provided. You have to put a wrench on both axle bolts to tighten
firmly.
6. Align the hole in the end of the connecting arm (pivoting rod end) with the hole in the
bracket of the handle bar. The rod end should be on the inside of the handle bar bracket.
Take one of the 1-1/4´ X 5/16´ bolts and install it through the handle bar bracket and the
rod end. Install a flat washer and Nylon nut on the bolt and tighten firmly using a wrench
on the nut and one on the bolt.
7. Repeat for the right side foot pad/connecting arm.
8. Install the plastic covers over the connection of the rod end and handle bar. The front
inside hole in the plastic uses a self-tapping screw and the two rear holes use the 3/8´
machine screws (short). There is a short Phillips screw driver provided for installing the
inside screws.
9. Install the two wheel covers using the four 5/8´ machine screws (long).
10.Install the locking pins for the adjustable footpads into the desired holes (XE350, XE550
only).
POWER CONNECTOR LOCATED ON
FRONT, LEFT HAND SIDE OF UNIT.
13
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing (EL3)
STEP 1 &2
14
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 &4
15
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing (EL5)
STEP 1 & 2
16
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 & 4
17
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Adjustable foot pedals (EL5 only), and orthopedically correct foot pads.
Through research performed with a leading sports scientist and physical rehabilitation expert,
Spirit engineering has developed a breakthrough in pedal design. No other elliptical, at any price,
offers these unique features. The history of elliptical use over the past few years tells us that many
users suffer from numb toes while working out on elliptical trainers. Many other users complain of
ankle, Achilles tendon, knee and/or hip pain. While researching a solution to these common
problems Spirit engineers consulted Richard DeKok, P.T., M.T.C., of St. Bernards Industrial
Rehabilitation Center in Jonesboro Arkansas.
Together we identified the inherent problem in elliptical designs and developed solutions to solve
the problems. What we found is that when you use an elliptical you tend to push outward during
the power stroke and not just straight back. This causes stress on the outer part of the foot and
throws off the natural alignment of the joints. The second problem we found is that many people
tend to stay up on the ball of their foot during the elliptical motion. Our solutions were simple but
effective:
·
·
The first solution was to add a 2-degree inward angle to the footpads. This might sound
simple but what it does is puts the users joints back into a neutral alignment. This eases
the over stressing of the ankles, knees and hips.
The second solution was to make the foot pedal adjustable to the user¶s style of pedaling
the elliptical. We achieved this by adding an adjustment that allows the angle of the footpad
to be changed. There are three adjustments. The lowest one will set the footpads at zero (0)
degrees, or flat at the bottom of the elliptical stroke. The second position sets the footpad to
five (5) degrees and the top position sets the footpads to ten (10) degrees. The adjustment
pull-pin is Located under the footpads.
Because every body is different, and there are as many styles to pedal an elliptical as there
are people, we found there is no one angle that fit every user. Some users would be up on
the balls of their feet, resulting in numb toes, so we decided to let the user adjust the back
of the foot pad upward to support the heel, taking the pressure off of the nerves in the balls
of the feet and the Achilles tendon. The result was no more numb toes. Some users are
uncomfortable at this angle so for them we designed in three different adjustable angles so
they could find one that feels best for them.
A great side benefit of the adjustable footpad angle is that you end up working different muscle
groups. At the highest angle you will work the quadriceps more. At the lowest angle you work the
hamstrings and gluteus harder. Not a bad perk!
Transportation
The elliptical is equipped with two transport wheels, which are engaged when rear of EL Series
Elliptical is lifted.
18
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of Your Elliptical
Getting familiar with the EL3 control panel
Power up
The Elliptical is supplied with an external power supply. When power is connected to the Elliptical,
the console will automatically power up. If there is no input to the console for 20 minutes the
console will go to stand-by mode. In stand-by mode the console display will turn off. To turn the
console on press any key.
When initially powered on the console will perform an internal self-test. During this time all the
lights will turn on. When the lights go off the dot matrix display will show a software version (i.e.:
VER 1.0) and the message window will display an odometer reading. The odometer reading
displays how many hours the elliptical has been used and how many virtual miles the elliptical has
gone. The time in hours will be to the left and the odometer in miles will be displayed to the right.
The odometer will remain displayed for only a few seconds, then the console will go to the start up
display. The dot matrix display will be scrolling through the different workout profiles of the
programs and the message window will be scrolling the start up message. You may now begin to
use the console.
19
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Operation
Quick Start mode
This is the quickest way to start a workout. After the console powers up you just press the Start
key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero
and the workload may be adjusted manually by pressing the Up or Down button. The dot matrix
display will show a 1/4-mile track with a lap counter in the center to monitor your progress.
Basic information and functions:
The Message Window:
Will initially be displaying the Time, Program name and Distance (in miles). Each time the Display
button is pressed the next set of information will appear, three sets of data in all. The next set of
information displayed is: Speed (in mph), RPM (pedaling speed) and Watts (indication of work
level). The third set displayed is: Calories, Level (work level from 1-20) and Pulse (heart rate in
beats per minute). Pressing the Display key one more time will set the display to scan mode
where the data will change every 4 seconds.
The Elliptical has a built in heart rate monitoring system. Simply grasping the hand pulse sensors
on the stationary handle bars, or wearing the heart rate transmitter, will start the Heart Icon
blinking (this may take a few seconds). The Pulse Display Window will display your heart rate, or
Pulse, in beats per minute.
The Stop/Reset button actually has several functions. Pressing the Stop/Reset key once during a
program will Pause the program for 5 minutes. If you need to get a drink, answer the phone or
any of the many things that could interrupt your workout, this is a great feature. To resume your
workout during Pause just press the Start key. If the Stop/Reset button is pressed twice during a
workout the program will end and a summary of your workout is displayed. If the Stop/Reset key is
held down for 3 seconds the console will perform a complete Reset. During data entry for a
program the Stop/Reset key performs a Previous Screen function. This allows you to go back
one step in the programming each time you press the Stop/Reset key.
Programming the console
Each of the programs can be customized with your personal information and changed to suit your
needs. Some of the information asked for is necessary to ensure the readouts are correct. You will
be asked for your Age and Weight. Entering your Age is necessary during the Heart Rate control
program to ensure the correct settings are entered in the program. Entering your Weight aides in
calculating a more correct Calorie reading. Although we cannot provide an exact calorie count we
do want to be as close as possible.
A message about Calories: Calorie readings on every piece of exercise equipment, whether it is
in a gym or at home, are not accurate and tend to vary widely. They are meant only as a guide to
monitor your progress from workout to workout. The only way to measure your calorie burn
accurately is in a clinical setting connected to a host of machines. This is because every person is
different and burns calories at a different rate. Some good news is that you will continue to burn
calories at about the same rate as during exercise for an hour or more after you have finished
exercising!
20
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering a program/Changing Settings
Use the Up or Down key to scroll through the program selections. The profile for each program will
be displayed in the dot matrix window. Press the enter key to select a program and begin
customizing the settings. If you want to workout without entering new settings then just press the
Start key. This will bypass the programming of data and take you directly to the start of your
workout. If you want to change the personal settings then just follow the instructions in the
message window. If you start a program without changing the settings, the default settings will be
used.
The default computer settings are: Age = 35, Weight = 155 Lbs., Time = 20:00, Max Level, each
program has a different maximum work level: Hill = 7, Fatburn = 5, Cardio = 7, Strength = 8,
Interval = 7.
NOTE: Age and Weight default settings will change when you enter a new number. So the last
Age and Weight entered will be saved as the new default settings. If you enter your Age and
Weight the first time you use the Elliptical you will not have to enter it every time you work out
unless either your Age or Weight changes or someone else enters a different Age and Weight.
Manual
The Manual program works as the name implies, manually. This means that you control the
workload yourself and not the computer. To start the Manual program follow the instructions below
or just press the Manual button then the Enter button and follow the directions in the message
window.
1. Highlight the Manual program then press the Enter key.
2. The message window will ask you to enter your Weight. You may adjust the weight setting
using the Up and Down keys, then press the Enter key to accept the new number and
proceed on to the next screen.
3. You are now asked to enter your Age. You may adjust the age setting using the Up and
Down keys then press enter to continue.
4. Next is the Time. You may adjust the Time and press enter to continue.
5. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Stop key to go back
one level of the programming screen.
6. Once the program starts the elliptical will be set to level one. This is the easiest level and it
is a good idea to stay at level one for a while to warm up. If you want to increase the work
load at any time press the Up key; the Down key will decrease the workload.
7. During the Manual program you will be able to scroll through the data in the message
window by pressing the Display key.
8. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up
display.
Preset Programs
The Elliptical has five different programs that have been designed for a variety of workouts. These
five programs have factory preset profiles for achieving different goals. The initial built-in level of
difficulty for each program is set to a relatively easy level. You may adjust the level of difficulty for
each program before beginning by following the instructions in the message window after
selecting your program.
21
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
The Programs
HILL
The Hill program simulates going up and down a hill. The resistance in the pedals will steadily
increase and then decrease during the program. To start the Hill program follow the instructions
below or just select the Hill program then the Enter button and follow the directions in the
message window.
1. Select the Hill program then press the Enter key.
2. The message window will ask you to enter your Weight. You may adjust the weight setting,
using the Up and Down keys, then press the Enter key to accept the new number and
proceed on to the next screen.
3. You are now asked to enter your Age. You may adjust the age number using the Up and
Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program (at the top of the hill). The factory setting is level seven. Adjust
the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Stop key to go back one
level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
8. During the Hill program you will be able to scroll through the data in the message window by
pressing the Display key.
9. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
Fat Burn
The Fat Burn program is designed, as the name implies, to maximize the burning of fat. There
are many schools of thought on the best way to burn fat but most experts agree that a lower
exertion level that stays at a steady workload is the best. The absolute best way to burn fat is to
keep your heart rate at around 60% to 70% of its maximum potential. This program does not use
heart rate but simulates a lower, steady exertion workout.
To start the Fat Burn program follow the instructions below or just select the Fat Burn program
then the Enter button and follow the directions in the message window.
1. Select the Fat Burn program then press the Enter key.
2. The message window will ask you to enter your Weight. You may enter your weight using the
Up and Down keys, then press the Enter key to accept the new number and proceed on to
the next screen.
3. You are now asked to enter your Age. You may adjust the age number using the Up and
Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing Stop key to go back one level,
or screen.
22
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
8. During the Fat Burn program you will be able to scroll through the data in the message
window by pressing the Display key.
9. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
Cardio
The Cardio program is designed to increase your Cardio vascular function. This is exercise for
your heart and lungs. It will build up your heart muscle and increase blood flow and lung capacity.
This is achieved by incorporating a higher level of exertion with slight fluctuations in work. To start
the Cardio program follow the instructions below or just select the Cardio program then the Enter
button and follow the directions in the message window
1. Select the Cardio program then press the Enter key.
2. The message window will ask you to enter your Weight. You may enter your weight using the
Up and Down keys, then press the Enter key to accept the new number and proceed on to
the next screen.
3. You are now asked to enter your Age. You may adjust the age number using the Up and
Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Stop key to go back one
level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
8. During the Cardio program you will be able to scroll through the data in the message window
by pressing the Display key.
9. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
Strength
The Strength program is designed to increase muscular strength in your lower body. This
program will steadily increase in resistance to a high level and then keeps you there. This is
designed to strengthen and tone your legs and glutes. To start the Strength program follow the
instructions below or just select Strength then the Enter button and follow the directions in the
message window.
1. Select the Strength program then press the Enter key.
2. The message window will ask you to enter your Weight. You may enter your weight using the
Up and Down keys, then press the Enter key to accept the new number and proceed on to
the next screen.
3. You are now asked to enter your Age. You may adjust the age number using the Up and
Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Max Level. This is the peak exertion level you will
23
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Stop key to go back one
level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
8. During the Strength program you will be able to scroll through the data in the message
window by pressing the Display key.
9. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
Interval
The Interval program takes you through high levels of intensity followed by periods of low intensity.
This program increases your endurance by depleting your oxygen level followed by periods of
recovery to replenish oxygen. Your cardio vascular system gets programmed to use oxygen more
efficiently this way. To start the Interval program follow the instructions below or just select the
Interval program then the Enter button and follow the directions in the message window.
1. Select the Interval program then press the Enter key.
2. The message window will ask you to enter your Weight. You may enter your weight using the
Up and Down keys, then press the Enter key to accept the new number and proceed on to
the next screen.
3. You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Stop key to go back one
level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
8. During the Interval program you will be able to scroll through the data in the message window
by pressing the Display key.
9. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
Custom User Defined Programs
The customizable User program allows you to build and save your own workout. You can build
your own custom program by following the instructions below.
1. Select the User program then press enter.
2. The message window will ask you to enter your Weight. You may enter your weight using the
Up and Down keys, then press the Enter key to accept the new number and proceed on to
the next screen.
3. You are now asked to enter your Age. You may adjust the age number using the Up and
Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
24
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Now the first column will be blinking and you are asked to adjust the level for the first
segment of the workout. When you finish adjusting the first segment, or if you don¶t want to
change, then press enter to continue to the next segment.
6. The next segment will show the same level as the previously adjusted segment. Repeat the
same process as the last segment then press enter. Continue this process until all twenty
segments have been set.
7. The message window will then tell you to start to begin (and save the program) or enter to
modify the program. Pressing Stop will exit to the start up screen.
8. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
9. During the User 1 or User 2 program you will be able to scroll through the data in the
message window by pressing the Display key.
10.When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
Heart Rate Control Program operation
To start the HRC program follow the instructions below or just select the HRC program then the
Enter button and follow the directions in the message window.
1. Select the HRC program then press the Enter key.
2. The message window will ask you to enter your Weight. You may enter your weight using the
Up and Down keys or the numeric key pad, then press the Enter key to accept the new
number and proceed on to the next screen.
3. You are now asked to enter your Age. You may adjust the age number using the Up and Down
keys or the numeric key pad, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the HRC percent. The default is 70%; you may select 60% or
80% also. Adjust the level and then press enter.
6. You are now asked to select the Target heart rate Level. This is the heart rate level you will
experience during the program. Adjust the level and then press enter.
7. Now you are finished editing the settings and can begin your workout by pressing the Start key.
You can also go back and modify your settings by pressing the Stop key to go back one level,
or screen.
8. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will allow you to change your target heart rate at any time during the
program.
9. During the HRC program you will be able to scroll through the data in the message window by
pressing the adjacent Display key.
10.When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time, then the console will return to the start-up display.
25
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting familiar with the EL5 control panel
Console Operation
Quick Start
This is the quickest way to start a workout. After the console powers up you just press the Start
key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero
and the workload may be adjusted manually by pressing the Up or Down buttons. The dot matrix
display will have only the bottom row lit at first. As you increase the work load more rows will light
indicating a harder workout. The elliptical will get harder to pedal as the rows increase.
Basic information
The Message Window will initially be displaying Speed information. Each time the Enter button is
pressed the next set of information will appear, four windows in all. In order: Speed in RPM and
MPH, Work Level and Watts. If the Enter button is pressed during the Level and Watts display the
Scan light will come on and the message window will show each set of data for four seconds then
switch to the next set of data in a continuous loop. Pressing the Enter button again will bring you
back to the beginning.
The Elliptical has a built in heart rate monitoring system. Simply grasping the hand pulse sensors
on the stationary handle bars, or wearing the heart rate transmitter, will start the Heart Icon
blinking (this may take a few seconds). The Pulse Display Window will display your heart rate, or
Pulse, in beats per minute.
The Stop/Reset button actually has several functions. Pressing the Stop/Reset key once during a
26
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
program will Pause the program for 5 minutes. If you need to get a drink, answer the phone or
any of the many things that could interrupt your workout, this is a great feature. To resume your
workout during Pause just press the Start key. If the Stop/Reset button is pressed twice during a
workout the program will end and the console will return to the start up screen. If the Stop/Reset
key is held down for 3 seconds the console will perform a complete Reset. During data entry for a
program the Stop/Reset key performs a Previous Screen function. This allows you to go back
one step in the programming each time you press the Stop/Reset key.
The Program Keys are used to preview each program. When you first turn the console on you
may press each program key to preview what the program profile looks like. If you decide that you
want to try a program, press the corresponding program key and then press the Enter key to
select the program and enter into the data setting mode.
The program keys also act as a Number Key Pad when you are in the data setting mode. Under
each program key is a number. If you are setting new data, such as Age, weight etc., you can use
these keys to enter the numbers quickly.
Programming the console
Each of the programs can be customized with your personal information and changed to suit your
needs. Some of the information asked for is necessary to ensure the readouts are correct. You will
be asked for your Age and Weight. Entering your Age is necessary during the Heart Rate control
programs to ensure the correct settings are in the program for your Age. Otherwise the work
settings could be too high or low for you. Entering your Weight aides in calculating a more correct
Calorie reading. Although we cannot provide an exact calorie count we do want to be as close as
possible.
A message about Calories: Calorie readings on every piece of exercise equipment, whether it is
in a gym or at home, are not accurate and tend to vary widely. They are meant only as a guide to
monitor your progress from workout to workout. The only way to measure your calorie burn
accurately is in a clinical setting connected to a host of machines. This is because every person is
different and burns calories at a different rate. Some good news is that you will continue to burn
calories at about the same rate as during exercise for 20-30 minutes after you have finished
exercising!
Entering/Changing Settings
When you enter a program, by pressing a program key, then enter key, you have the option of
entering your own personal settings. If you want to workout without entering new settings then just
press the Start key. This will bypass the programming of data and take you directly to the start of
your workout. If you want to change the personal settings then just follow the instructions in the
message window. If you start a program without changing the settings the default, or saved,
settings will be used.
The default computer settings are: Age = 35, Weight = 155 Lbs., Time = 30:00, Max Level, each
program has a different maximum work level: Hill = 7, Fatburn = 5, Cardio = 7, Strength = 8,
Interval = 7.
NOTE: Age and Weight default settings will change when you enter a new number. So the last
Age and Weight entered will be saved as the
new default settings. If you enter your Age and
27
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Weight the first time you use the Elliptical you will not have to enter it every time you work out
unless either your Age or Weight changes or someone else enters a different Age and Weight.
Manual
The Manual program works as the name implies; manually. This means that you control the
workload yourself and not the computer. To start the Manual program follow the instructions below
or just press the Manual button then the Enter button and follow the directions in the message
window.
9. Press the Manual key then press the Enter key.
10.The message window will ask you to enter your Age. You may enter your Age, using the
Up and Down keys or the numeric key pad, then press the Enter key to accept the new
number and proceed on to the next screen.
11.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
12. Next is Time. You may adjust the Time and press enter to continue.
13.Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At
any time during the editing of Data you can press the Stop key to go back one level, or
screen.
14.Once the program starts you will be at level one. This is the easiest level and it is a good
idea to stay at level one for a while to warm up. If you want to increase the work load at any
time press the Up key; the Down key will decrease the work load.
15.During the Manual program you will be able to scroll through the data in the message
window by pressing the Enter key.
16.When the program ends you may press Start to begin the same program again or Stop to
exit the program or you can save the program you just completed as a custom user
program by pressing a User key and following the instructions in the message window.
Preset Programs
The Elliptical has five different programs that have been designed for a variety of workouts. These
five programs have factory preset profiles for achieving different goals. The initial built-in level of
difficulty for each program is set to a relatively easy level. You may adjust the level of difficulty for
each program before beginning by following the instructions in the message window after
selecting your program.
The Programs
HILL
The Hill program simulates going up and down a hill. The resistance in the pedals will steadily
increase and then decrease during the program. To start the Hill program follow the instructions
below or just press the Hill button then the Enter button and follow the directions in the message
window.
10.Press the Hill key then press the Enter key.
11.The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
28
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
12.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
13.Next is Time. You may adjust the Time and press enter to continue.
14.Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program, at the top of the hill. The factory setting is level seven. Adjust
the level and then press enter.
15.Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
16.If you want to increase or decrease the work load at any time during the program press the
Up or Down key. This will only affect the workload for the present position in the profile. When
the profile changes to the next column it will return to the preset work level.
17.During the Hill program you will be able to scroll through the data in the message window by
pressing the Enter key.
18.When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
Fat Burn
The Fat Burn program is designed, as the name implies, to maximize the burning of fat. There
are many schools of thought on the best way to burn fat but most experts agree that a lower
exertion level that stays steady is the best. The absolute best way to burn fat is to keep your heart
rate at around 60% to 70% of its maximum potential. This program does not use heart rate but
simulates a lower, steady, exertion workout.
To start the Fat Burn program follow the instructions below or just press the Fat Burn button then
the Enter button and follow the directions in the message window.
10.Press the Fat Burn key then press the Enter key.
11.The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
12.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
13.Next is Time. You may adjust the Time and press enter to continue.
14.Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. The factory setting is level five. Adjust the level and then
press enter.
15.Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
16.If you want to increase or decrease the work load at any time during the program press the
Up or Down key. This will only affect the workload for the present position in the profile. When
the profile changes to the next column it will return to the preset work level.
17.During the Fat Burn program you will be able to scroll through the data in the message
window by pressing the Enter key.
18.When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
29
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Cardio
The Cardio program is designed to increase your Cardio vascular function. This is, simply said,
exercise for your heart and lungs. It will build up your heart muscle and increase blood flow and
lung capacity. This is achieved by incorporating a higher level of exertion with slight fluctuations in
work. To start the Cardio program follow the instructions below or just press the Cardio button then
the Enter button and follow the directions in the message window.
10.Press the Cardio key then press the Enter key.
11.The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
12.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
13.Next is Time. You may adjust the Time and press enter to continue.
14.Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. The factory setting is level seven. Adjust the level and then
press enter.
15.Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
16.If you want to increase or decrease the work load at any time during the program press the
Up or Down key. This will only affect the workload for the present position in the profile. When
the profile changes to the next column it will return to the preset work level.
17.During the Cardio program you will be able to scroll through the data in the message window
by pressing the Enter key.
18.When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
Strength
The Strength program is designed to increase muscular strength in your lower body. This
program will steadily increase in resistance to a high level and then keeps you there. This is
designed to strengthen and tone your legs and gluteus. To start the Strength program follow the
instructions below or just press the Strength button then the Enter button and follow the directions
in the message window.
10.Press the Strength key then press the Enter key.
11.The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
12.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
13.Next is Time. You may adjust the Time and press enter to continue.
14.Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. The factory setting is level eight. Adjust the level and then
press enter.
15.Now you are finished editing the settings and can begin your workout by pressing the Start
30
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
16.If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
17.During the Strength program you will be able to scroll through the data in the message
window by pressing the Enter key.
18.When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
Interval
The Interval program takes you through high levels of intensity followed by periods of low intensity.
This program increases your endurance by depleting your oxygen level followed by periods of
recovery to replenish oxygen. Your cardio vascular system gets programmed to use oxygen more
efficiently this way. To start the Interval program follow the instructions below or just press the
Interval button then the Enter button and follow the directions in the message window.
11.Press the Interval key then press the Enter key.
12.The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
13.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
14.Next is Time. You may adjust the Time and press enter to continue.
15.Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. The factory setting is level seven. Adjust the level and then
press enter.
16.Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
17.If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
18.During the Interval program you will be able to scroll through the data in the message window
by pressing the Enter key.
19.When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
Custom User Defined Programs
There are two customizable User programs that allow you to build and save your own workout.
The two programs, User 1 and User 2, operate exactly the same way so there is no reason to
describe them separately. You can build your own custom program by following the instructions
below or you can save any other preset program you complete as a custom program. Both
programs allow you to further personalize it by adding your name.
31
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Press the User 1 or User 2 key. The message window will show a welcome message. If you
had previously saved a program the message will contain your name. Then press the Enter
key to begin programming.
11.When you press enter, the message window will show ³Name ± A´, if there is no name saved.
If the name ³David´ had been previously saved the message window will show ³Name ±
David´ and the D will be blinking. If there is a name saved you can change it or you may
press the Stop key to keep the name and continue to the next step. If you want to enter a
name use the Up and/or the Down key to change the first letter then press Enter to save the
first letter and continue to the next letter. When you have finished entering the name press
the Stop key to save the name and continue to the next step.
12.The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
13.You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
14.Next is Time. You may adjust the Time and press enter to continue.
15.Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. The factory setting is level seven. Adjust the level and then
press enter.
16.Now the first column will be blinking and you are asked to adjust the level for the first
segment of the workout. When you finish adjusting the first segment, or if you don¶t want to
change, then press enter to continue to the next segment.
17.The next segment will show the same level as the previously adjusted segment. Repeat the
same process as the last segment then press enter. Continue this process until all twenty
segments have been set.
18.The message window will then tell you to press enter to save the program. After saving the
program the message window says ³New program saved´ then will give you the option to
Start or modify the program. Pressing Stop will exit to the start up screen.
19.If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
20.During the User 1 or User 2 program you will be able to scroll through the data in the
message window by pressing the Enter key.
32
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Heart Rate programs
Before we get started, a word about Heart Rate:
The old motto, ³no pain, no gain´, is a myth that has been overpowered by the benefits of
exercising comfortably. A great deal of this success has been promoted by the use of heart rate
monitors. With the proper use of a heart rate monitor, many people find that their usual choice of
exercise intensity was either too high or too low and exercise is much more enjoyable by
maintaining their heart rate in the desired benefit range.
To determine the benefit range in which you wish to train, you must first determine your Maximum
Heart Rate. This can be accomplished by using the following formula: 220 minus your age. This
will give you the Maximum heart rate (MHR) for someone of your age. To determine the effective
heart rate range for specific goals you simply calculate a percentage your MHR. Your Heart rate
training zone is 50% to 90% of your maximum heart rate. 60% of your MHR is the zone that burns
fat while 80% is for strengthening the cardio
vascular system. This 60% to 80% is the zone
to stay in for maximum benefit.
For someone who is 40 years old their target
heart rate zone is calculated:
220 ± 40 = 180 (maximum heart rate)
180 x .6 = 108 beats per minute (60% of
maximum)
180 X .8 = 144 beats per minute (80% of
maximum)
So for a 40 year old the training zone would
be 108 to 144 beats per minute.
If you enter your age during programming the
console will perform this calculation automatically. Entering your age is used for the Heart Rate
control programs and also for the Heart rate bar graph. After calculating your Maximum Heart
Rate you can decide upon which goal you would like to pursue.
The two most popular reasons for, or goals, of exercise are cardiovascular fitness (training for the
heart and lungs) and weight control. The black columns on the chart below represent the
Maximum Heart Rate for a person whose age is listed at the bottom of each column. The training
heart rate, for either cardiovascular fitness or weight loss, is represented by two different lines that
cut diagonally through the chart. A definition of the lines¶ goal is in the bottom left-hand corner of
the chart. If your goal is cardiovascular fitness or if it is weight loss, it can be achieved by training
at 80% or 60%, respectively, of your Maximum Heart Rate on a schedule approved by your
physician. Consult your physician before participating in any exercise program.
With all Spirit Heart Rate Control elliptical machines you may use the heart rate monitor feature
without using the Heart Rate Control program. This function can be used during manual mode or
during any of the nine different programs. The Heart Rate Control program automatically controls
resistance at the pedals.
33
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Rate of Perceived Exertion
Heart rate is important but listening to your body also has a lot of advantages. There are more
variables involved in how hard you should workout than just heart rate. Your stress level, physical
health, emotional health, temperature, humidity, the time of day, the last time you ate and what
you ate, all contribute to the intensity at which you should workout. If you listen to your body, it will
tell you all of these things.
The rate of perceived exertion (RPE), also know as the Borg scale, was developed by Swedish
physiologist G.A.V. Borg. This scale rates exercise intensity from 6 to 20 depending upon how you
feel or the perception of your effort.
The scale is as follows:
Rating Perception of Effort
6 Minimal
7 Very,very light
8 Very,very light +
9 Very light
10 Very light +
11 Fairly light
12 Comfortable
13 Somewhat hard
14 Somewhat hard +
15 Hard
16 Hard +
17 Very hard
18 Very hard +
19 Very,very hard
20 Maximal
You can get an approximate heart rate level for each rating by simply adding a zero to each rating.
For example a rating of 12 will result in an approximate heart rate of 120 beats per minute. Your
RPE will vary depending up the factors discussed earlier. That is the major benefit of this type of
training. If your body is strong and rested, you will feel strong and your pace will feel easier. When
your body is in this condition, you are able to train harder and the RPE will support this. If you are
feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will
feel harder. Again, this will show up in your RPE and you will train at the proper level for that day.
34
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Heart Rate Transmitter
How to wear your wireless chest strap transmitter:
1. Attach the transmitter to the elastic strap using the locking parts.
2. Adjust the strap as tightly as possible as long as the strap is not too tight to remain comfortable.
3. Position the transmitter with the POLAR logo centered in the middle of your body facing away
from your chest (some people must position the transmitter slightly left of center). Attach the
final end of the elastic strap by inserting the round end and, using the locking parts, secure the
transmitter and strap around your chest.
4. Position the transmitter immediately below the pectoral muscles.
5. Sweat is the best conductor to measure very minute heart beat electrical signals. However,
plain water can also be used to pre-wet the electrodes (2 black square areas on the reverse
side of the belt and either side of transmitter). It¶s also recommended that you wear the
transmitter strap a few minutes before your work out. Some users, because of body chemistry,
have a more difficult time in achieving a strong, steady signal at the beginning. After ³warming
up´, this problem lessens. As noted, wearing clothing over the transmitter/strap doesn¶t affect
performance.
6. Your workout must be within range - distance between transmitter/receiver ± to achieve a
strong steady signal. The length of range may vary somewhat but generally stay close enough
to the console to maintain good, strong, reliable readings. Wearing the transmitter immediately
against bare skin assures you of proper operation. If you wish, you may wear the transmitter
over a shirt. To do so, moisten the areas of the shirt that the electrodes will rest upon.
Erratic Operation:
Caution! Do not use this elliptical for Heart Rate Control unless a steady, solid Actual Heart
Rate value is being displayed. High, wild, random numbers being displayed indicate a
problem.
Areas to look for interference which may cause erratic heart rate:
(1) Microwave ovens, TV¶s, small appliances, etc.
(2) Fluorescent lights.
(3) Some household security systems.
(4) Perimeter fence for a pet.
(5) Some people have problems with the transmitter picking up a signal from their skin. If you
have problems try wearing the transmitter upside down. Normally the transmitter will be oriented
so the spirit logo is right side up.
(6) The antenna that picks up your heart rate is very sensitive. If there is an outside noise source,
turning the whole machine 90 degrees may de-tune the interference.
(7) If you continue to experience problems contact your dealer.
35
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Heart Rate Control Program 1 & 2 (HR 1, HR 2) operation
Both programs operate the same, the only difference is that HR 1 is set to 60% and HR 2 is set to
80% of maximum heart rate. They both are programmed the same way.
To start the HR 1 or HR 2 programs follow the instructions below or just press the HR 1 or HR 2
button then the Enter button and follow the directions in the message window.
1. Press the HR 1 or HR 2 key then press the Enter key.
2. The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
3. You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Heart rate Level. This is the heart rate level you will
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will allow you to change your target heart rate at any time during the
program.
8. During the HR 1 or HR 2 programs you will be able to scroll through the data in the message
window by pressing the Enter key.
9. When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
36
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance:
1. Wipe down all areas in the sweat path with a damp cloth after each workout.
2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two
reasons:
i.
The hardware was not sufficiently tightened during assembly. All bolts that were
installed during assembly need to be tightened as much as possible. It may be
necessary to use a larger wrench than the one provided if you cannot tighten the
bolts sufficiently. I cannot stress this point enough; 90% of calls to the service
department for noise issues can be traced to loose hardware or the rear rails being
dirty.
ii.
Dirt build-up on the rear rails and polyurethane wheels are also a source of noise.
Noise from build-up on the rails can cause a thumping sound that you would swear
is coming from inside the main body of the machine because noise travels, and is
amplified, in the tubing of the frame. Clean the rails and wheels with a lint free cloth
and rubbing alcohol. Stubborn build-up can be removed with your thumbnail or a
non-metallic scraper, like the back edge of a plastic knife. After cleaning, apply a
small amount of lubricant on the rails with your fingers or a lint free cloth. You only
need a thin coat of lubrication, wipe off any excess.
3. If squeaks or other noises persist, check that the unit is properly leveled. There are 4 leveling
pads on the bottom of the rear rails, use a 14mm wrench (or adjustable wrench) to adjust the
levelers.
Maintenance Menu in console software:
The console has built in maintenance/diagnostic software. The software will allow you to change
the console settings from English to Metric and turn off the beeping of the speaker when a key is
pressed for example. To enter the Maintenance menu (may be called Engineering mode,
depending on version) press and hold down the Start, Stop and Enter keys. Keep holding the keys
down for about 5 seconds and the message window will display ³ALTXXXX Engineering mode´.
Press the enter button to access the menu below:
a. Key test (will allow you to test all the keys to make sure they are functioning)
b. Display test (tests all the display functions)
c. Functions (Press enter to access settings)
i. Sleep mode (Turn on to have the console power down automatically after
20 minutes of inactivity)
ii. Pause Mode (Turn on allow 5 minutes of pause, turn off to have the
console pause indefinitely)
iii. ODO reset (reset the odometer)
iv. Units (Set to English or Metric display readings)
v. Beep (Turn on or off the beep when a key is pressed)
vi. Motor test (continually runs the tensioning gear motor)
vii. Exit
d. Security (Allows you to lock the keypad so no unauthorized use is allowed)
e. Factory settings (Access only allowed by manufacturing)
37
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer’s Limited Warranty
Effective January 1, 2007
ELLIPTICAL WARRANTY
Spirit Manufacturing Inc. warrants all its elliptical parts, for a period of time listed below, from the date of retail sale, as determined by sale receipt,
or in the absence of a sales receipt eighteen (18) months from the original factory shipping date, whichever comes first. Spirit¶s responsibilities
include providing new or remanufactured parts, at Spirit¶s option, and technical support to our independent dealers and servicing organizations. In
the absence of a dealer or service organization, these warranties will be administered by Spirit directly to a consumer. An extended warranty period
applies to the following components:
EL3
EL5
Labor
1 Year
Lifetime
2 Years
Lifetime
1 Year
Frame Weldments
All Other Components
Brake
Lifetime
3 years
Lifetime
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to
validate the manufacturer¶s limited warranty.
2. Proper use of the elliptical in accordance with the instructions provided in this manual
3. Proper installation by an authorized Spirit service company in accordance with instructions provided with the elliptical and with all local electric
codes.
4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house
wiring.
5. Expenses for making the elliptical accessible for servicing, including any item that was not part of the elliptical at the time it was shipped from the
factory.
6. Damages to the elliptical finish during shipping, installation or following installation.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or
defects in workmanship or material, for units that are beyond the warranty period, for units that are beyond the service call
reimbursement period, for elliptical not requiring component replacement, or elliptical not in ordinary household use.
3. Damages caused by services performed by persons other than authorized Spirit service companies; use of parts other than original
Spirit parts; or external causes such as alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power supply, or
acts of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at Spirit Mfg. Spirit reserves the right to request proof of
purchase if no warranty record exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory
shipping as determined by the serial number establishes the warranty period should service be required. If service is performed,
it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have
other rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order:
1. Contact your selling authorized Spirit dealer. OR
2. Contact your local authorized Spirit service organization.
3. If there is a question as to where to obtain service, contact our service department at (870) 935-1107.
4. If no local service is available, Spirit will repair or replace the parts, at Spirit¶s option, within the warranty period at no charge
for parts. All transportation costs, both to our factory and upon return to the owner, are the responsibility of the owner. The owner is responsible for
adequate packaging upon return to Spirit. Spirit is not responsible for damages in shipping. Make all freight damage claims with the appropriate
freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN AUTHORIZATION NUMBER. All units arriving without a
return authorization number will be refused.
5. For any further information, or to contact our service department by mail, send your correspondence to:
Spirit Manufacturing, Inc.
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by
Spirit Manufacturing, Inc. This warranty applies only in the 50 states of the U.S.A.
38
EL3 /EL5 Elliptical
Download from Www.Somanuals.com. All Manuals Search And Download.
|