2-683-494-62 (1)
Micro HI-FI
Component
System
Operating Instructions
Owner’s Record
e model and serial numbers are located on the rear of the unit. Record these
numbers in the space provided below. Refer to them whenever you call upon your
Sony dealer regarding this product.
Model No. ______________ Serial No. ______________
CMT-U1BT
© 2006 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Note to CATV system installer:
Note on DualDiscs
is reminder is provided to call the CATV
system installer’s attention to Article 820-40 of
the NEC that provides guidelines for proper
grounding and, in particular, specifies that
the cable ground shall be connected to the
grounding system of the building, as close to the
point of cable entry as practical.
A DualDisc is a two sided disc product which
mates DVD recorded material on one side
with digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Music discs encoded with copyright
protection technologies
Notice for the customers in Canada
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may
cause undesired operation of this device.
is product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
is equipment complies with IC radiation
exposure limits set forth for uncontrolled
equipment and meets the RSS-102 of the IC
radio frequency (RF) Exposure rules.
• e Bluetooth word mark and logos are owned
by the Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under license.
Other trademarks and trade names are those
of their respective owners.
• “WALKMAN” and “WALKMAN” logo are
registered trademarks of Sony Corporation.
is equipment has a very low RF energy level
that is deemed to comply with RSS-102 without
maximum permissive exposure evaluation
(MPE). But it is desirable that it should be
installed and operated with at least 20cm and
more between the radiator and person’s body
(excluding extremities: hands, wrists, feet and
legs).
• MICROVAULT is a trademark of Sony
Corporation.
• ATRAC, ATRAC3, ATRAC3plus and their
U.S.A., Canadian and Australian models
only
logos are trademarks of Sony Corporation.
• SonicStage and SonicStage logo are trademarks
or registered trademarks of Sony Corporation.
• MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
omson.
ENERGY STAR® is a U.S.
registered mark. As an
ENERGY STAR® partner, Sony
Corporation has determined
that this product meets the
ENERGY STAR® guidelines for
energy efficiency.
ꢁGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
ꢂGB
Download from Www.Somanuals.com. All Manuals Search And Download.
is manual mainly explains operations using
the remote, but the same operations can also be
performed using the buttons on the unit having
the same or similar names.
Guide to parts and controls
Unit (HCD-U1BT/Compact Disc Receiver)
/ (power) button (page 10, 20,
23, 27)
Press to turn on the system.
STANDBY indicator (page 19, 24)
Lights up when the system is turned off.
VOLUME +/– button (page 11, 13,
16, 17, 18)
Press to adjust the volume.
Sound buttons (page 19)
Unit: DSGX button
Remote: EQ button
Press to select the sound.
Remote sensor (page 24)
(headphones) jack
Connect the headphones.
AUDIO IN jack (page 18)
Connect to an optional audio component.
Remote (RM-SCU35)
(USB) port (page 17, 33)
Connect to an optional USB device (Digital
music player or USB storage media).
Unit: CANCEL (stop/cancel)
button (page 11, 13, 15, 16, 17)
Remote: (stop) button (page 11,
13, 15, 16, 17)
Press to stop playback.
Press to cancel search.
SEARCH button (page 11, 17, 20)
Press to enter or exit search mode. Press
when the system is turned off to enter text
mode.
Continued
ꢃGB
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTER button (page 10, 20, 21, 22,
23)
Press to enter the settings.
Playback buttons and function
buttons
BLUETOOTH (play) button
(page 16)
Press to select the BLUETOOTH function.
Press to start playback of the music on
the BLUETOOTH device (BLUETOOTH
mobile phone, etc.).
/ (go back/go forward)
button (page 11, 17, 21)
Press to select a track or file.
Unit: TUNE +/– (tuning) button
(page 13)
Remote: +/– (tuning) button
(page 13)
Unit: USB (play/pause)
button (page 17)
Press to select the USB function.
Press to start or pause playback of an
optional USB device (Digital music player
or USB storage media).
Remote: USB button (page 17)
Press to select the USB function.
Press to tune in the desired station.
Unit: / (folder and file search)
button (page 11, 17)
Press to select a folder and file.
Remote:
button (page 11, 17, 21)
Press to select a folder.
+/– (select folder)
Unit: CD (play/pause) button
(page 11)
Press to select the CD function.
Press to start or pause playback of a disc.
Remote: CD button (page 11)
Press to select the CD function.
/ (rewind/fast forward)
button (page 11, 17)
Press to find a point in a track or file.
Remote: (play) button,
(pause) button
Press to start or pause playback.
Indicators
BLUETOOTH indicator
Lights up when you select the
BLUETOOTH function.
TUNER/BAND button (page 13)
Press to select the TUNER function. Press
to select FM or AM reception mode.
USB indicator
Lights up when an optional USB device
(Digital music player or USB storage
media) is connected.
AUDIO IN button (page 18)
Press to select the AUDIO IN function.
(play) indicator
Lights up when a track or file is being
played back.
FUNCTION button
Press to select the function.
(eject) button (page 11)
(pause) indicator
Press to eject a disc.
Lights up when a track or file is paused.
Disc slot
(disc presence) indicator
Lights up when a disc is loaded.
6GB
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK/TIMER SELECT button (page
23)
CLOCK/TIMER SET button (page
10, 23)
Information on the display
Press to set the clock and the timers.
REPEAT/FM MODE button (page 11,
13, 17)
Press to listen to a disc, a single track or file
repeatedly. Press to select the FM reception
mode (monaural or stereo).
Battery compartment lid (page 10)
CLEAR button (page 15, 21)
Press to delete a pre-programmed track or
file. Press to erase the pairing registration
information of the BLUETOOTH device.
Text information
Timer (page 23)
TUNER MEMORY button (page 22)
Press to preset the radio station.
Tuner reception mode (page 13)
Tuner reception (page 13)
PLAY MODE/TUNING MODE button
(page 12, 13, 18, 21, 22)
Play mode (page 12, 18)
Audio format
Press to select the play mode of a CD,
“ATRAC” disc, MP3 disc or an optional
USB device (Digital music player or USB
storage media).
DSGX (page 19)
Press to select the tuning mode.
DISPLAY button (page 16, 19)
Press to change the information on the
display.
SLEEP button (page 23)
Press to set the Sleep Timer.
ꢄGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Hooking up the system securely
Speakers
Left speaker
Right speaker
Antennas
Find a location and an orientation that
provide good reception, and then set up the
antenna.
Keep the antennas away from the speaker
cords, the power cord and the USB cable to
avoid picking up noise.
FM lead antenna
(Extend it horizontally.)
or
Brown side for other regions
White side for North American
model
ꢅGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Power
Connect the power cord to a wall
socket.
If the plug does not fit the wall
socket, detach the supplied
plug adaptor (only for models
equipped with an adaptor).
Wall socket
Continued
AM loop antenna
ꢆGB
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the remote
Slide and remove the battery compartment lid
Setting the clock
, and insert the two supplied R6 (size AA)
batteries, side first, matching the polarities
1
Press / (power)
to turn on the
shown below.
system.
2
Press CLOCK/TIMER SET
.
If the current mode appears on the display,
press /
repeatedly to select
.
“CLOCK SET?” and then press ENTER
3
4
Press / repeatedly to set
the hour, and then press ENTER
.
Use the same procedure to set the
minutes.
Notes
• With normal use, the batteries should last for about six
months.
When you turn off the system aſter setting
• Do not mix an old battery with a new one or mix
different types of batteries.
• If you do not use the remote for a long period of time,
remove the batteries to avoid damage from battery
leakage and corrosion.
the clock, the clock display appears instead
of the demonstration display.
e clock settings are lost when you
disconnect the power cord or if a power
failure occurs.
10GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Start playback.
Press (or CD on the unit)
.
Basic Operations
Adjust the volume.
Press VOLUME +/–
Playing a CD/ATRAC/MP3
disc
.
Other operation
To
Pause playback
1
Select the CD function.
Press
Press CD
.
(or CD on the
unit) . To resume play,
press the button again.
2
Insert a disc in the disc slot
the label side facing forward.
with
Stop playback
.
Select a folder
on an “ATRAC”
disc or MP3 disc
+/– (or / on the
.
unit)
Insert a disc with
the label side
facing forward.
Select a track
or file
/
.
Select a folder
and file on an
“ATRAC” disc or
MP3 disc using
the buttons on
the unit
SEARCH . Press /
to select the desired
folder, then press ENTER
. Press /
to select
the desired file, then press
ENTER
.
Notes
• When you turn on the system, the disc is not
pulled into the disc slot until “No Disc” appears
in the display. Do not attempt to push in the disc
until “No Disc” appears.
• Do not insert a disc with non-standard shapes (e.
g., heart, square, star). The disc may fall into the
system and cause irreparable damage.
• When pressing on the unit and then reinserting
the disc that appears in the disc slot, do not simply
push in the disc. Remove the disc from the disc slot
and then reinsert it.
Find a point in a
track or file
Hold down /
during playback, and
release the button at the
desired point.
Select Repeat
Play
REPEAT
repeatedly
until “REP” or “REP1”
appears.
Eject a disc
on the unit.
• Do not turn off the system with a disc halfway inserted
in the disc slot. Doing so may cause the disc to fall.
• Do not use a disc with tape, seals or paste on it as this
may cause malfunction.
• When you eject a disc, handle the disc by its edge. Do
not touch the surface.
• Do not push a disc into the disc slot when the system is
off. Doing so may cause the system to malfunction.
• Do not insert an 8 cm disc with an adaptor. Doing so
may cause the system to malfunction.
Continued
11GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on playing “ATRAC”/MPꢁ discs
• Do not save other types of files or unnecessary folders
on a disc that has “ATRAC” and MP3 files.
• Folders that have no “ATRAC” and MP3 files are
skipped.
• “ATRAC” and MP3 files are played back in the order
that they are recorded onto the disc.
• e system can only play MP3 files that have a file
extension of “.MP3”.
To change the play mode
Press PLAY MODE
repeatedly while the
player is stopped. You can select normal play
(“ *” for all “ATRAC” files and MP3 files in
the folder on the disc), shuffle play (“SHUF” or
“
*
SHUF*”), or program play (“PGM”).
When playing a CD-DA disc,
(SHUF) Play
performs the same operation as SHUF Play.
• If there are files on the disc that have the “.MP3” file
extension, but that are not MP3 files, the unit may
produce noise or may malfunction.
• e maximum number of:
– “ATRAC” folders is 255.
– “ATRAC” files is 999.
– MP3 folders is 255 (including the root folder).
– MP3 files is 511.
– MP3 files and folders that can be contained on a
single disc is 512.
– folder levels (the tree structure of files) is 8.
• Compatibility with all MP3 encoding/writing soſtware,
recording device, and recording media cannot be
guaranteed. Incompatible MP3 discs may produce
noise or interrupted audio or may not play at all.
• If “ATRAC” files and MP3 files are recorded on the
same disc, this system plays the “ATRAC” files first.
To create an “ATRAC”/MP3 disc
You can create an “ATRAC” disc and MP3 disc
with the SonicStage soſtware. SonicStage can be
downloaded free of charge from the following
sites and installed on your computer.
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
For customers in Canada:
<http://www.sony.ca/ElectronicsSupport/>
Please see the instructions at the sites or
SonicStage Help of the soſtware for how to
install and how to create an “ATRAC”/MP3
disc.
Notes on Repeat Play
• All tracks or files on a disc are played repeatedly up to
five times.
Notes on playing multisession discs
• If the disc begins with a CD-DA (or “ATRAC”/MP3)
session, it is recognized as a CD-DA (or “ATRAC”/
MP3) disc, and other sessions are not played back.
• “REP1” indicates that a single track or file is repeated
until you stop it.
• A disc with a mixed CD format is recognized as a CD-
DA (audio) disc.
1ꢀGB
Download from Www.Somanuals.com. All Manuals Search And Download.
To tune in a station with a weak signal
If “TUNED” does not appear and the scanning
Listening to the radio
does not stop, press TUNING MODE
repeatedly until “AUTO” and “PRESET”
1
Select “FM”or “AM.”
Press TUNER/BAND
disappear, and then press +/– (or TUNE +/– on
repeatedly.
the unit)
station.
repeatedly to tune in the desired
2
Select the tuning mode.
Press TUNING MODE
repeatedly until
To reduce static noise on a weak FM stereo
station
“AUTO” appears.
Press FM MODE
repeatedly until “MONO”
3
Tune in the desired station.
appears to turn off stereo reception.
Press +/– (or TUNE +/– on the unit)
. Scanning stops automatically when a
station is tuned in, and then “TUNED” and
“STEREO” (for stereo programs) appear.
4
Adjust the volume.
Press VOLUME +/–
.
To stop automatic scanning
.
Press
1ꢁGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Pairing this system with a
BLUETOOTH device
Listening to music of a
BLUETOOTH mobile phone
or BLUETOOTH device
is is a Micro HI-FI Component System
incorporating BLUETOOTH wireless
technology for enabling you to listen to music
from your BLUETOOTH mobile phone
or BLUETOOTH device over a wireless
connection.
Pairing is an operation where BLUETOOTH
devices register with each other beforehand.
Use the procedure below to pair the system
with your BLUETOOTH device. Once a
pairing operation is performed, it does not
need to be performed again. If pairing is
already completed, proceed to “Playing music
of a BLUETOOTH device” (page 16).
is system supports the A2DP and AVRCP
profiles. For details on BLUETOOTH wireless
technology, see “BLUETOOTH wireless
technology” (page 31).
1
Place the BLUETOOTH device to be
connected to this system within
1 meter of the system.
Check the websites below for the latest
information about compatible devices.
For customers in the U.S.A.:
2
3
Select the BLUETOOTH function.
Press BLUETOOTH
on the unit.
<http://www.sony.com/shelfsupport>
For customers in Canada:
Operate the BLUETOOTH device and
perform the pairing operation.
<http://www.sony.ca/ElectronicsSupport/>
For details about the operations of
the BLUETOOTH device, refer to the
operation manual supplied with your
BLUETOOTH device.
When searching for this system with the
BLUETOOTH device, a list of the devices
found may appear in the BLUETOOTH
device display depending on the type of
BLUETOOTH device.
is system appears as “CMT-U1BT.”
When establishing the connection with
this system, select the audio profile (A2DP,
AVRCP) at the BLUETOOTH device. If
the BLUETOOTH device does not support
the AVRCP profile, you cannot perform
playback or other operations with the
system (page 16).
Follow the procedure below to listen to music
from BLUETOOTH devices with this system.
Pairing this system with a BLUETOOTH
device
Connecting to registered devices
Playing music of a BLUETOOTH device
For details about the operations of the
BLUETOOTH device, also refer to the
operation manual supplied with your
BLUETOOTH device.
1ꢂGB
Download from Www.Somanuals.com. All Manuals Search And Download.
To erase all the pairing registration
information
4
Enter the passcode.
Passcode entry may be required depending
on the type of BLUETOOTH device.
1
Press BLUETOOTH
on the unit.
For details about the operations of
the BLUETOOTH device, refer to the
operation manual supplied with your
BLUETOOTH device.
When the system is connected with
a BLUETOOTH device (when the
BLUETOOTH device name appears in
the system display), turn off the system
or change the function to cancel the
connection.
Enter the passcode at the system as follows:
.
2
3
Press CLEAR
“Delete?” appears.
.
Press ENTER
“Complete!” appears and all the pairing
information is erased.
Note
In order to connect with a BLUETOOTH device aſter
performing this operation, you must enter the passcode
again.
“PIN?” and a countdown appear.
Press /
and /
to enter
the same passcode that was entered at
the BLUETOOTH device, and then press
.
ENTER
Once pairing is completed and the
connection is established, the system
display changes as follows:
“Connect”
device
Name of the BLUETOOTH
To cancel passcode entry partway
.
Press
Notes
• “Passcode” may be called “Passkey,” “PIN code,” “PIN
number” or “Password,” etc. depending on the device.
• is system only supports numerical passcodes up to
13 digits.
• e pairing standby status of the system is cancelled
aſter about 30 seconds. If pairing is not successful, redo
the procedure from step 1.
• While connected to a BLUETOOTH device, this
system cannot be detected and a connection cannot be
established from another BLUETOOTH device.
Continued
1ꢃGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Other operation
To
Playing music of a BLUETOOTH device
Press
Pause playback
.
You can operate a BLUETOOTH device by
connecting the system and a BLUETOOTH
device using AVRCP. If the system is not
connected with a BLUETOOTH device using
AVRCP, “Not in Use” appears when you
operate the system.
Stop playback
Select a file
.
.
/
Find a point in
a file
.
Hold down /
1
2
Select the BLUETOOTH function.
Note
Press BLUETOOTH
on the unit.
ese operations may not be available for certain
BLUETOOTH devices. In addition, the actual operations
may differ according to the connected BLUETOOTH
device.
Establish the connection from the
BLUETOOTH device.
For details about the operations of
the BLUETOOTH device, refer to the
operation manual supplied with your
BLUETOOTH device.
Note on connections with BLUETOOTH
devices
If you cannot connect with a paired BLUETOOTH
device, perform the pairing operation between the system
and the BLUETOOTH device again.
Once the connection is established, the
system display changes as follows:
“Connect”
device
Name of the BLUETOOTH
3
4
Start playback.
Press (or BLUETOOTH on the
.
unit)
Depending on the BLUETOOTH device,
you may need to start up the AV soſtware of
the BLUETOOTH device beforehand.
Adjust the volume.
Press VOLUME +/–
.
To check the address of a connected
BLUETOOTH device
Press DISPLAY
while the BLUETOOTH
device name appears in the system display.
e BLUETOOTH device address appears for
8 seconds.
To cancel the connection with a BLUETOOTH
device
Change the system’s function or turn off
the system. When using the system next
time, reestablish the connection with the
BLUETOOTH device.
16GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
It may take about 10 seconds before “Detect” appears
depending on the type of USB device connected.
Listening to music of an
USB device
3
4
Start playback.
Press (or USB on the unit)
.
You can connect an optional USB device
(Digital music player or USB storage media) to
Adjust the volume.
Press VOLUME +/–
the
(USB) port
on the unit and listen to
.
music stored in the USB device. See “Playable
USB devices and BLUETOOTH devices”
(page 33) for a list of USB devices that can be
connected to this system.
Other operation
To
Press
e audio formats that can be played back
by this system are as follows: ATRAC/MP31)/
WMA1)/AAC1)2)
Pause playback
(or USB on the
unit) . To resume play,
press the button again.
1) Files with copyright protection (Digital Rights
Management) cannot be played by this system.
Stop playback
Select a folder
.
2) AAC files transferred to a digital music player using
SonicStage CP cannot be played by this system.
+/– (or / on the
unit)
.
1
2
Select the USB function.
Select a file
/
.
Press USB
.
Select a folder
and file using the
buttons on the
unit*
SEARCH . Press /
to select the desired
folder, then press ENTER
Connect an optional USB device
(Digital music player or USB storage
media) to the (USB) port as
shown below.
. Press /
to select
the desired file, then press
ENTER
.
Find a point in
a file
Hold down /
during playback, and
release the button at the
desired point.
Select Repeat
Play
REPEAT
repeatedly
until “REP” or “REP1”
appears.
USB device (Digital music player or
USB storage media)
Remove the USB
device
Hold down
until
“Device Stop” appears, then
remove the USB device.
When USB cable connection is necessary,
connect the USB cable supplied with the
USB device to be connected.
See the operation manual supplied with the
USB device to be connected for details on
the operation method.
*
Artist searches and group searches are possible for
some USB device types.
When the USB device is connected, the
display changes as follows:
“Detect”
“Connecting”
“ATRAC
AD” or “STORAGE DRIVE”
Continued
1ꢄGB
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the play mode
Press PLAY MODE
repeatedly while the
Using optional audio
components
USB device is stopped. You can select normal
play (“ ” for all files in the folder on the
digital music player), shuffle play (“SHUF” or “
SHUF”), or program play (“PGM”).
1
Connect additional audio component
to the AUDIO IN jack
on the unit
Notes on the USB device
using an audio analog cord (not
supplied).
• With some connected USB devices, aſter an operation
is performed, there may be a delay before it is
performed by this system.
• is system does not necessarily support all the
functions provided in a connected USB device.
2
3
4
Turn down the volume.
Press VOLUME –
.
• e playback order for the system may differ from the
playback order of the connected USB device.
• Always press
and make sure that “Device Stop”
Select the AUDIO IN function.
appears before removing the USB device. Removing
the USB device while “Device Stop” is not displayed
may corrupt the data on it or damage the USB device
itself.
Press AUDIO IN
on the unit.
Start playing the connected
component.
• Do not save other types of files or unnecessary folders
on an USB device that has audio files.
• Folders that have no audio files are skipped.
• Files are played back in the order that they are
transferred to the USB device.
5
Adjust the volume.
Press VOLUME +/–
.
• e maximum numbers of folders and files that can be
contained on a single USB device are as follows:
– Digital music player: 65,535 groups (maximum 999
tracks per group)/65,535 tracks
– USB storage media: 512 folders (including the root
folder, maximum 999 files per folder, maximum 255
folders per folder)/65,535 files
e maximum number of files and folders may vary
depending on the file and folder structure.
• e audio formats that you can listen to with this
system are as follows:
– MP3: file extension “.mp3”
– Windows Media file: file extension “.wma”
– AAC: file extension “.m4a”
Note that even when file names have the above file
extensions, if the actual file differs, the system may
produce noise or may malfunction.
• Compatibility with all encoding/writing soſtwares,
recording devices, and recording media cannot be
guaranteed. Incompatible USB device may produce
noise or interrupted audio or may not play at all.
1ꢅGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound
Changing the display
To add a sound effect
To
Press
Change
DISPLAY
when the system is turned
on.
repeatedly
To
Press
information on
the display1)2)
Generate a
more dynamic
sound
DSGX
on the unit.
Change Display
mode (See
below.)
DISPLAY
when the system is turned
off.
repeatedly
(Dynamic
Sound
Generator
X-tra)
1)
For example, you can view CD/“ATRAC”/MP3 disc
information or the USB device information, such as
the track or file number or folder name during normal
play, or the total playing time while the player is
stopped.
When the system and a BLUETOOTH device are
connected using the BLUETOOTH function, you can
view the BLUETOOTH device address.
Set the sound
effect
EQ
repeatedly to select
“BASS” or “TREBLE,” and
then press +/–
to adjust the level.
repeatedly
2)
e system offers the following display modes.
Display mode When the system is off1),
Demonstration e demonstration
indicator is displayed.
Clock
e clock is displayed.
Power Saving
e display is turned off
to conserve power. e
timer and clock continue to
operate.
Mode2)
1)
e STANDBY indicator
the system is off.
on the unit lights up when
2)
When the system is in Power Saving Mode, the
following functions are unavailable:
– setting the clock.
– changing the AM tuning interval.
– changing the CD power manage function.
– resetting the system to factory settings.
– selecting the text mode.
Continued
1ꢆGB
Download from Www.Somanuals.com. All Manuals Search And Download.
To select the text mode
You can select from a variety of languages for
displaying the text information on a disc or an
USB device. Use buttons on the unit for the
operation.
1
2
Press /
to turn off the system.
.
Press SEARCH
e language list appears. e languages you
can select vary depending on the country or
region specification.
3
Press /
to select the language, and
then press ENTER
.
Notes on the display information
• Characters that cannot be displayed appear as “_”.
• e information on the disc or USB device may not be
displayed correctly in the selected text mode.
• e following are not displayed:
– total playing time for a CD-DA disc depending on
the play mode.
– total playing time for an “ATRAC”/MP3 disc.
• e following are not displayed correctly:
– elapsed playing time of an “ATRAC” file or MP3 file
encoded using a VBR (variable bit rate).
– folder and file names that do not follow either the
ISO9660 Level 1, Level 2 or Joliet in the expansion
format.
• e following are displayed:
– ID3 tag information for “ATRAC” files and MP3 files
when ID3 version 1 and version 2 tags are used.
– up to 62 characters of ID3 tag information.
ꢀ0GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press ENTER
to the program.
to add the track or file
Other Operations
CD
Creating your own program
(Program Play)
“– –.– –” appears when the total program
time exceeds 100 minutes for a CD, or
when you select a CD track whose number
is 21 or over, or when you select an
“ATRAC” file or MP3 file.
Use buttons on the remote to create your own
program.
USB
1
CD
Select the desired function.
e total program time cannot be
displayed, so “– –.– –” appears.
Press CD
to select the CD function.
5
6
Repeat steps 3 through 4 to program
additional tracks or files, up to a total
of 25 tracks or files.
USB
Press USB
to select the USB function.
To play your program of tracks or
repeatedly until
2
Press PLAY MODE
“PGM”appears while the system is
stopped.
files, press
.
e program remains available until you
remove the disc or USB device. When using
an USB device, the program disappears
when the system is turned off. To play the
3
Press /
the desired track or file number
appears.
When programming files, press
repeatedly to select the desired folder, and
then select the desired file.
repeatedly until
.
same program again, press
+/–
To cancel Program Play
Press PLAY MODE
repeatedly until “PGM”
disappears while the system is stopped.
Example: When programming tracks on
a CD
To delete the last track or file of the program
Press CLEAR
while the system is stopped.
Selected track or file number
Total playing time of program
(including selected track or file)
ꢀ1GB
Download from Www.Somanuals.com. All Manuals Search And Download.
6
To call up a preset radio station,
Presetting radio stations
press TUNING MODE
until “PRESET”appears, and then
repeatedly
You can preset your favorite radio stations
and tune them in instantly by selecting the
corresponding preset number.
press +/–
repeatedly to select the
desired preset number.
Use buttons on the remote to preset stations.
1
2
Tune in the desired station (see
“Listening to the radio”(page 13)).
Press TUNER MEMORY
.
Preset number
repeatedly to select your
desired preset number.
3
Press +/–
If another station is already assigned to
the selected preset number, the station is
replaced by the new stations.
.
4
5
Press ENTER
Repeat steps 1 through 4 to store
other stations.
You can preset up to 20 FM and 10 AM
stations. e preset stations are retained for
about half a day even if you disconnect the
power cord or if a power failure occurs.
ꢀꢀGB
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Use the same procedure as in step 4
to set the time to stop playing.
Using the Timers
e system offers two timer functions. If you
use the Play Timer with the Sleep Timer, the
Sleep Timer has priority.
Select the sound source.
Press /
repeatedly until the
desired sound source appears, and then
press ENTER . e display shows the
Sleep Timer:
You can fall asleep to music. is function
works even if the clock is not set.
timer settings.
to turn off the system.
Press SLEEP
repeatedly. If you select
7
Press /
“AUTO,” the system automatically turns off
aſter the current disc stops or in 100 minutes.
e system turns on 15 seconds before the
preset time. If the system is on at the preset
time, the Play Timer will not play.
Play Timer:
You can wake up to CD, tuner or optional USB
To activate or check the timer again
device at a preset time.
Press CLOCK/TIMER SELECT , press
Use buttons on the remote to control the Play
Timer. Make sure you have set the clock.
/
repeatedly until “PLAY
.
SELECT?” appears, and then press ENTER
1
Prepare the sound source.
To cancel the timer
Prepare the sound source, and then press
VOLUME +/–
to adjust the volume.
Repeat the same procedure as above until
To start from a specific CD track, “ATRAC”
file or MP3 file of a disc, create your own
program (page 21).
“TIMER OFF” appears, and then press ENTER
.
To change the setting
.
2
3
Press CLOCK/TIMER SET
Start over from step 1.
Note
Press /
repeatedly to
select “PLAY SET?,”and then press
You cannot perform Program Play of the files on an USB
device using the Play Timer.
ENTER
.
Tip
“ON” appears, and the hour indication
e Play Timer setting remains as long as the setting is
not canceled manually.
flashes.
4
Set the time to start playing.
Press /
repeatedly to set
.
the hour, and then press ENTER
e minute indication flashes. Use the
procedure above to set the minutes.
ꢀꢁGB
Download from Www.Somanuals.com. All Manuals Search And Download.
The remote does not function.
• Remove any obstacles between the remote
Others
and the remote sensor
on the unit, and
position the unit away from fluorescent
lights.
• Point the remote at the system’s sensor.
• Move the remote closer to the system.
Troubleshooting
1
Make sure the power cord and speaker
cords are correctly and firmly connected.
2
Find your problem in the checklist below,
and take the indicated corrective action.
If the issue persists, contact your nearest
Sony dealer.
CD/“ATRAC”/MP3 player
The sound skips, or the disc will not play.
• Wipe the disc clean, and replace it.
• Move the system to a location away from
vibration (for example, on top of a stable
stand).
• Move the speakers away from the system,
or place them on separate stands. At high
volume, speaker vibration may cause the
sound to skip.
If the STANDBY indicator flashes
Immediately unplug the power cord, and
check the following item.
• If your system has a voltage selector, is the
voltage selector set to the correct voltage?
• Are you using only the supplied speakers?
• Is anything blocking the ventilation holes
on the top or back of the system?
Play does not start from the first track.
Aſter the STANDBY indicator
stops
• Press PLAY MODE
repeatedly until both
flashing, reconnect the power cord, and turn
on the system. If the issue persists, contact
your nearest Sony dealer.
“PGM” and “SHUF” disappear to return to
normal play.
Starting playback takes more time than
usual.
• e following discs take a longer time to start
playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in multisession mode.
– a disc that has not been finalized (a disc to which
data can be added).
– a disc that has many folders.
General
The display starts flashing as soon as you
plug in the power cord even though you
have not turned on the system.
• Press DISPLAY
while the system is off.
e demonstration disappears.
Sound comes from one channel, or the left
and right volumes are unbalanced.
• Place the speakers as symmetrically as
possible.
• Connect only the supplied speakers.
Severe hum or noise.
• Move the system away from sources of noise.
• Connect the system to a different wall socket.
• Install a noise filter (available separately) to
the power cord.
ꢀꢂGB
Download from Www.Somanuals.com. All Manuals Search And Download.
BLUETOOTH device
USB device
Pairing cannot be done.
Are you using a supported USB device?
• Move the BLUETOOTH device closer to the
system.
• If you connect an unsupported USB device,
the following problems may occur. See
“Playable USB devices and BLUETOOTH
devices” (page 33) for the supported device
types.
Connection is not possible.
• e BLUETOOTH device you attempted
to connect does not support the A2DP and
AVRCP profiles, and cannot be connected
with the system.
• Enable the BLUETOOTH function of the
BLUETOOTH device.
– e USB device is not recognized.
– File or folder names are not displayed on this system.
– Playback is not possible.
– e sound skips.
– ere is noise.
• e pairing registration information has been
erased. Perform the pairing operation again.
• While connected to a BLUETOOTH
device, this system cannot be detected and
a connection cannot be established from
another BLUETOOTH device.
“Over Current” appears.
• A problem has been detected with the level
of electrical current from the
(USB) port
. Turn off the system and remove the USB
device from the
(USB) port . Make sure
there is no problem with the USB device. If
this display pattern persists, contact your
nearest Sony dealer.
The sound skips or fluctuates, or the
connection is lost.
• e system and the BLUETOOTH device are
There is no sound.
too far apart.
• e USB device is not connected correctly.
Turn off the system, then reconnect the USB
device and check if the USB indicator
lights up.
• If there are obstacles between the system and
your BLUETOOTH device remove or avoid
the obstacles.
• If there is equipment that generates
electromagnetic radiation, such as a wireless
LAN, other BLUETOOTH device, or a
microwave oven nearby, move them away.
The sound is distorted.
• e bit rate used when encoding the files was
low. Send files encoded with higher bit rates
to the USB device.
The sound of your BLUETOOTH device
cannot be heard.
There is noise or the sound skips.
• Turn up the volume on your BLUETOOTH
device first, and then adjust the volume using
• Turn off the system, then reconnect the USB
device.
VOLUME +/–
on the unit.
• e music data itself contains noise. Noise
may have been introduced when creating
music data due to the conditions of the
computer. Create the music data again.
• When using the USB storage media, copy
the files to your computer, format the USB
storage media in FAT16 or FAT32 format,
and copy the files to the USB storage media
again.*
Severe hum or noise
• If there are obstacles between the system and
your BLUETOOTH device remove or avoid
the obstacles.
• If there is equipment that generates
electromagnetic radiation, such as a wireless
LAN, other BLUETOOTH device, or a
microwave oven nearby, move them away.
• Turn down the volume of the connected
BLUETOOTH device.
Continued
ꢀꢃGB
Download from Www.Somanuals.com. All Manuals Search And Download.
The USB device cannot be connected into
Files cannot be played back.
.
the
(USB) port
• USB storage media formatted with file
systems other than FAT16 or FAT32 are
unsupported.*
• If you use partitioned USB storage media,
only files on the first valid partition can be
played.
• e USB device is being connected
backwards. Connect the USB device in the
correct orientation.
The USB storage media which has been
used on another device does not work.
• Files that are encrypted or protected by
passwords, etc. cannot be played back.
• It may be recorded in an unsupported
format. If so, first take the precaution of
backing up important files on the USB
storage media by copying them to your
computer hard disk. Next, format the USB
storage media with a FAT16 or FAT32 file
system and transfer the backed-up audio files
onto the USB storage media again.*
*
is system supports FAT16 and FAT32, but some USB
storage media may not support all of these FAT. For
details, see the operation manual of each USB storage
media or contact the manufacturer.
Tuner
Severe hum or noise, or stations cannot be
received. (“TUNED” or “STEREO” flashes on
the display.)
“Connecting” is displayed for a long time.
• It may take a while to finish reading the
USB device if there are many folders or files
on it. us, we recommend following these
guidelines.
– Total folders on USB device: 100 or less
– Total files per folder: 100 or less
• Connect the antenna properly.
• Find a location and an orientation that
provide good reception, and then set up the
antenna again.
• Keep the antennas away from the speaker
cords, the power cord and the USB cable to
avoid picking up noise.
• Connect a commercially available external
antenna.
Erroneous display
• Send the music data to the USB device again,
as the data stored in the USB device may
have been corrupted.
• Consult your nearest Sony dealer if the
supplied AM antenna has come off the plastic
stand.
Play does not start.
• Turn off the system, then reconnect the USB
device.
• Connect the USB device that this system can
play.
• Press (or USB on the unit)
start play.
• Turn off nearby electrical equipment.
To change the AM tuning interval
e AM tuning interval is factory-preset to 9
kHz (or 10 kHz, for some areas). You cannot
change the AM tuning interval in Power Saving
Mode.
Use buttons on the unit to change the AM
tuning interval.
to
Play does not start from the first track.
• Set the play mode to Normal Play mode.
1
Tune in any AM station, and then turn off
the system.
,
2
While holding down TUNER/BAND
press /
.
All the AM preset stations are erased. To
reset the interval to the factory preset, repeat
the procedure.
ꢀ6GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To improve tuner reception
Turn off CD player power by using the CD
power management function. By default, CD
power is turned on. You cannot change the
setting in Power Saving Mode.
Messages
CD/ATRAC/MP3 player, Tuner
Complete!: e preset operation ended
Use buttons on the unit to turn off CD player
power.
normally.
LOCKED: e system does not eject the disc.
Contact your nearest Sony dealer.
No Disc: ere is no disc in the system, or you
have loaded a disc that cannot be played.
1
Press FUNCTION
repeatedly to select
the CD function, and then turn off the
system.
No Step: All of the programmed tracks or files
2
After “STANDBY”stops flashing, press /
have been erased.
.
while holding down
Not in Use: You pressed an invalid button.
OFF TIME NG!: e Play Timer start and end
times are set to the same time.
“CD POWER OFF” appears. With CD
player power turned off, disc access time
is increased. To turn on CD player power,
repeat the procedure until “CD POWER
ON” appears.
Over: You have reached the end of the disc
while pressing
pause.
during playback or
Push SELECT!: You tried to set the clock or
To reset the system to factory settings
If the system still does not operate properly,
reset the system to factory settings. You cannot
reset the system to factory settings in Power
Saving Mode. Use buttons on the unit to reset
the system to its factory default settings.
timer during timer operation.
Push STOP!: You pressed PLAY MODE
during playback.
Reading: e system is reading information of
the disc. Some buttons are not available.
SET CLOCK!: You tried to select the timer when
the clock is not set.
SET TIMER!: You tried to select the timer when
the Play Timer is not set.
Step Full!: You tried to program more than 26
tracks or files (steps).
1
Disconnect and reconnect the power cord,
and then turn on the system.
2
Press DSGX
time.
and /
at the same
All user-configured settings, such as preset
radio stations, timer, and the clock, are
deleted.
Continued
ꢀꢄGB
Download from Www.Somanuals.com. All Manuals Search And Download.
BLUETOOTH device
Connect: BLUETOOTH communication was
Precautions
Discs that this system CAN play
• Audio CD
• CD-R/CD-RW (audio data “ATRAC” files/
MP3 files)
established.
Disconnect: Communication with a
BLUETOOTH device was cut off for some
reason, or BLUETOOTH communication
was ended by the BLUETOOTH device.
Not in Use: e system is not connected with a
BLUETOOTH device using AVRCP.
PIN?: e system is asking for the passcode.
For details, see “Listening to music
of a BLUETOOTH mobile phone or
BLUETOOTH device” (page 14).
Discs that this system CANNOT play
• CD-ROM
• CD-R/CD-RW other than those recorded in
music CD format, “ATRAC” format or MP3
format conforming to ISO9660 Level 1/Level
2, Joliet or multisession
USB device
• CD-R/CD-RW recorded in multisession that
have not ended by “closing the session”
ATRAC AD: An ATRAC Audio Device is
• CD-R/CD-RW of poor recording quality,
CD-R/CD-RW that have scratches or are
dirty, or CD-R/CD-RW recorded with an
incompatible recording device
• CD-R/CD-RW which is finalized incorrectly
• Discs containing files other than MPEG 1
Audio Layer-3 (MP3) files
connected.
Connecting: e system is recognizing the
USB device.
Detect: An USB device is connected.
Device Error: e USB device could not
be recognized or an unknown device is
connected.
Device Stop: e USB device has been
• Discs of non-standard shape (for example,
heart, square, star)
• Discs that have adhesive tape, paper, or
sticker attached to them
• Rental or used discs with attached seals
where the glue extends beyond the seal
• Discs that have labels printed using ink that
feels tacky when touched
stopped.
No Device: No USB device is connected.
No Info: e system cannot display the track
information (folder name, file name, etc).
No Step: All of the programmed tracks or files
have been erased.
Not Supported: An unsupported USB device
is connected.
No Track: No playable file is loaded in the
system.
Not in Use: You have made an invalid or
currently prohibited operation.
Please Wait: e system is readying for usage
of an USB device.
Removed: e USB device has been removed.
Step Full!: You tried to program more than 26
tracks or files (steps).
STORAGE DRIVE: USB storage media is
connected.
ꢀꢅGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on discs
On heat buildup
• Before playing, wipe the disc with a cleaning
cloth from the center out to the edge.
• Heat buildup on the unit during operation is
normal and is not cause for alarm.
• Do not clean discs with solvents, such as
benzine thinner, or commercially available
cleaners or anti-static spray intended for
vinyl LPs.
• Do not touch the cabinet if it has been used
continuously at a high volume because the
cabinet may have become hot.
• Do not obstruct the ventilation holes.
• Do not expose discs to direct sunlight or heat
sources such as hot air ducts, nor leave it in a
car parked in direct sunlight.
On the speaker system
is speaker system is not magnetically
shielded, and the picture on nearby TV
sets may become magnetically distorted. In
this situation, turn off the TV, wait 15 to 30
minutes, and turn it back on. If there is no
improvement, move the speakers far away from
the TV.
On safety
• Completely disconnect the power cord
(mains lead) from the wall socket (mains)
if it is not going to be used for an extended
period of time. When unplugging the unit,
always grip the plug. Never pull the cord
itself.
• Should any solid object or liquid get into
the system, unplug the system, and have
it checked by qualified personnel before
operating it again.
Cleaning the cabinet
Clean this system with a soſt cloth slightly
moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring
powder, or solvent, such as thinner, benzine, or
alcohol.
• e AC power cord can be changed only by a
qualified service facility.
On placement
• Do not place the system in an inclined
position or in locations that are extremely
hot, cold, dusty, dirty, or humid or lacking
adequate ventilation, or subject to vibration,
direct sunlight or a bright light.
• Be careful when placing the unit or speakers
on surfaces that have been specially treated
(for example, with wax, oil, polish) as
staining or discoloration of the surface may
result.
• If the system is brought directly from a cold
to a warm location or is placed in a very
damp room, moisture may condense on
the lens inside the CD player, and cause the
system to malfunction. In this situation,
remove the disc, and leave the system turned
on for about an hour until the moisture
evaporates.
ꢀꢆGB
Download from Www.Somanuals.com. All Manuals Search And Download.
USB section
Supported bit rate
Specifications
MP3 (MPEG 1 Audio Layer-3):
32 – 320 kbps, VBR
Main unit (HCD-U1BT/Compact Disc Receiver)
ATRAC: 48 – 352 kbps (ATRAC3 plus),
66/105/132 kbps (ATRAC3)
WMA: 48 – 192 kbps, VBR
AAC: 48 – 320 kbps
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(e United States model only)
Sampling frequencies
With 6 ohm loads, both channels driven, from
120 – 10,000 Hz; rated 25 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
MP3 (MPEG 1 Audio Layer-3):
32/44.1/48 kHz
ATRAC: 44.1 kHz
WMA: 44.1 kHz
AAC: 44.1 kHz
Amplifier section
CD player section
DIN power output (rated): 20 + 20 watts
(6 ohms at 1 kHz, DIN)
System: Compact disc and digital audio system
Laser Diode Properties
Continuous RMS power output (reference):
25 + 25 watts (6 ohms at 1 kHz, 10% THD)
Inputs:
Emission duration: continuous
Laser Output*: Less than 44.6µW
*is output is the value measurement at a
distance of 200mm from the objective lens
surface on the Optical Pick-up Block with 7mm
aperture.
AUDIO IN (stereo mini jack):
voltage 620 mV, impedance 47 kilohms
(USB) port: Type A, maximum current
500 mA
Frequency response: 20 Hz – 20 kHz
Outputs:
(PHONES (stereo mini jack)): accepts
headphones of 8 ohms or more
SPEAKER: accepts impedance of 6 ohms
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section:
BLUETOOTH section
Tuning range: 87.5 – 108.0 MHz (100 kHz step)
Communication system:
BLUETOOTH Standard version 2.0
Output:
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section:
BLUETOOTH Standard Power Class 2
Maximum communication range:
Line of sight approx. 10 m1)
Frequency band:
Tuning range:
530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,710 kHz (with 9 kHz tuning interval)
Antenna: AM loop antenna, external antenna
terminal
2.4 GHz band (2.4000 GHz – 2.4835 GHz)
Modulation method:
FHSS
Intermediate frequency: 450 kHz
Compatible BLUETOOTH profiles2):
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote Control
Profile)
Audio format:
SBC (Sub Band Codec)
e actual range will vary depending on factors such
1)
as obstacles between devices, magnetic fields around a
microwave oven, static electricity, reception sensitivity,
antenna’s performance, operating system, soſtware
application, etc.
BLUETOOTH standard profiles indicate the purpose
of BLUETOOTH communication between devices.
2)
ꢁ0GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker (SS-CU1BT)
Speaker system: 2-way, 2-unit, bass-reflex
BLUETOOTH wireless
technology
BLUETOOTH wireless technology is a short-
range wireless technology linking digital
devices, such as personal computers and digital
still cameras. Using the BLUETOOTH wireless
technology, you can operate the units involved
within a range of about 10 meters.
type
Speaker units: Woofer 10 cm, Aluminum
cone type, Tweeter 2 cm, soſt dome type
Nominal impedance: 6 ohms
Dimensions (w/h/d): Approx. 150 × 241 ×
225 mm
Mass: Approx. 2.3 kg net per speaker
General
Power requirements: 120 V AC, 60 Hz
e BLUETOOTH wireless technology is
commonly used between two devices, but a
single device can be connected to multiple
devices.
Power consumption: 35 watts
Dimensions (w/h/d) (excl. speakers): Approx. 160
× 241 × 218 mm
Mass (excl. speakers) 3.2 kg
You do not need wires to get connected as you
do with a USB connection, and you do not
need to place the devices face to face as you do
with wireless infrared technology. You can use
the technology with one BLUETOOTH device
in your bag or pocket.
Supplied accessories: Remote Commander (RM-
SCU35) (1), R6 (Size AA) batteries (2), AM loop
antenna (1), FM lead antenna (1)
U.S. and foreign patents licensed from Dolby
Laboratories.
Design and specifications are subject to change
without notice.
BLUETOOTH wireless technology is a
global standard supported by thousands of
companies. ese companies produce products
that meet the global standard.
• Standby power consumption: 0.5 W
• Halogenated flame retardants are not
used in the certain printed wiring
boards.
• Halogenated flame retardants are not
used in cabinets.
(Except for the United States model)
Supported BLUETOOTH version and profiles
Profile refers to a standard set of capabilities
for various BLUETOOTH product capabilities.
is system supports the following
BLUETOOTH version and profiles.
Supported BLUETOOTH version:
BLUETOOTH Standard version 2.0
Supported BLUETOOTH profiles:
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote Control
Profile)
Continued
31GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Effective communication range
• is system supports security functions that comply
with the BLUETOOTH specification as a means
of ensuring security during communication using
BLUETOOTH technology. However, this security may
be insufficient depending on the setting contents and
other factors, so always be careful when performing
communication using BLUETOOTH technology.
• Sony cannot be held liable in any way for damages or
other loss resulting from information leaks during
communication using BLUETOOTH technology.
BLUETOOTH devices should be used within
approximately 10 meters (unobstructed
distance) of each other. e effective
communication range may become shorter
under the following conditions.
– When a person, metal object, wall or other
obstruction is between the devices with a
BLUETOOTH connection
– Locations where a wireless LAN is installed
– Around microwave ovens that are in use
– Locations where other electromagnetic waves
occur
• BLUETOOTH communication is not necessarily
guaranteed with all BLUETOOTH devices that have
the same profile as this system.
• BLUETOOTH devices connected with this system
must comply with the BLUETOOTH specification
prescribed by the BLUETOOTH SIG, Inc., and must
be certified to comply. However, even when a device
complies with the BLUETOOTH specification, there
may be cases where the characteristics or specifications
of the BLUETOOTH device make it impossible to
connect, or may result in different control methods,
display or operation.
• Noise may occur or the audio may cut off depending
on the BLUETOOTH device connected with this
system, the communications environment, or
surrounding conditions.
Effects of other devices
BLUETOOTH devices and wireless LAN
(IEEE 802.11b/g) use the same frequency band
(2.4 GHz). When using your BLUETOOTH
device near a device with wireless LAN
capability, electromagnetic interference may
occur. is could result in lower data transfer
rates, noise, or inability to connect. If this
happens, try the following remedies:
– Try connecting this system and
BLUETOOTH mobile phone or
BLUETOOTH device when you are at least
10 meters away from the wireless LAN
equipment.
– Turn off the power to the wireless LAN
equipment when using your BLUETOOTH
device within 10 meters.
Effects on other devices
e radio waves broadcast by this system may
interfere with the operation of some medical
devices. Since this interference may result in
malfunction, always turn off the power on
this system, BLUETOOTH mobile phone
and BLUETOOTH device in the following
locations:
– In hospitals, on trains, in airplanes, at gas
stations, and any place where flammable
gasses may be present
– Near automatic doors or fire alarms
ꢁꢀGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Verified Sony USB storage media (as of April
2006)
Playable USB devices and
BLUETOOTH devices
Product name Model name
MICROVAULT
USM32D / 64D / 128D /
256D / 512D / 1GD
USB devices
USM64D/V / 128D/V /
256D/V / 512D/V / 1GD/V
You can play back the following Sony USB
devices on this system. Other USB devices
cannot be played back on this system.
USM128E / 256E / 512E /
1GE / 2GE
USM128E/V / 256E/V /
512E/V / 1GE/V / 2GE/V
Verified Sony digital music player (as of April
2006)
USM512EX / 1GEX /
2GEX
Product name Model name
USM128J / 256J / 512J /
1GJ / 2GJ / 4GJ
NW-E103 / E105 / E107
NW-E205 / E207
Walkman
USM512JX / 1GJX / 2GJX /
4GJX
NW-E303 / E305 / E307
NW-E403 / E405 / E407
NW-E503 / E505 / E507
NW-A605 / A607 / A608
USD2G / 4G / 5G / 8G
Check the websites below for the latest
information about compatible devices.
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
For customers in Canada:
<http://www.sony.ca/ElectronicsSupport/>
NW-E002 / E002F / E003 /
E003F / E005 / E005F
NW-HD5
NW-A1000 / A1200 /
A3000
Notes
• Do not use USB devices other than these USB devices.
Operation of models not listed here is not guaranteed.
• Operation may not always be ensured even when using
these USB devices.
• Some of these USB devices may not be available for
purchase in certain areas.
Note
AAC files transferred to a digital music player using
SonicStage CP cannot be played by this system.
BLUETOOTH devices
You can check the websites below for the
BLUETOOTH compatible devices.
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
For customers in Canada:
<http://www.sony.ca/ElectronicsSupport/>
ꢁꢁGB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢂGB
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢃGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed on 100% recycled
paper using VOC (Volatile Organic
Compound)-free vegetable oil
based ink
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|
