SVAT Electronics DVR CVDVR200 User Manual

Model #: CVDVR200  
User Manual  
now you can see  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL PANEL AND FUNCTION  
FRONT PANEL  
View Control Buttons  
1. Mobile Rack  
2. Key Socket  
3. Hard Disk in-use Indicator  
4. Power Indicator  
15. View Full Screen from Camera 1  
16. View Quad Screen and display  
all cameras  
17. View Full Screen from Camera 2  
18. View Full Screen from Camera 3  
19. View Full Screen from Camera 4  
20. Remote Control Socket  
Playback Control Buttons  
5. Rewind Playback button  
6. Stop Button  
REAR PANEL  
7. ||Pause Button  
21. Video Output Terminal  
22. Video Input Terminal  
23. Sensor Connecting Terminal  
24. Alarm Connecting Terminal  
25. LAN Connector Socket  
26. Power ON/OFF Switch  
27. AC Power Cord  
8. Fast Forward and Skip Button  
9. Play Button  
Function Control Buttons  
10. REC: Record Button  
11. SELECT: Select Button  
12 Move Up Button  
13: Move Down Button  
14. MENU: OSD Menu Button  
ꢆꢃꢄꢅꢀꢂꢇꢁ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
1. Hard Disk installation  
The system supports Dual Hard Disk recording feature. Please carefully follow the  
steps as below to install Hard Disk Driver. Install the Hard Disk into mobile rack  
1.Take out the  
mobile rack.  
3. If you decide to use two  
Hard Disks in the colour  
mintor with the DVR system.  
you have to designate one  
as a master and the other  
as a slave.  
2.Take off the  
top cover  
4. Connect the cable  
and power cord.  
5.Screw the hard  
disk on.  
6.Close the top cover and  
insert the mobile rack to  
colour monitor with DVR.  
When the Hard Disk is installed, you have to lock the mobile rack so that the  
DVR system can work.  
Replace the Hard Disk from DVR  
1. Press STOP button to stop recording.  
2. Turn off the power of DVR.  
3. Take out the Hard Disk from mobile rack and/or fixed hard disk rack.  
4. Insert the new Hard Disk.  
5. Lock the mobile rack again.  
6. Turn on the power of mobile rack.  
7. Press REC button for recording.  
SENSOR & ALARM INSTALLATION  
When you want to install the sensor and/or alarm to the DVR, please refer to the  
following picture for installation.  
1. Sensor  
Connect the wire one end to sensor and the other end to the sensor terminal.  
The adapter has to be inserted to the sensor when the wire is connected. If you  
don t know positive or negative while installing sensor output wire, the cross test  
can be done and see if it can work normally.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SENSOR & ALARM INSTALLATION  
2. Alarm  
Connect the wire of alarm one pin to alarm terminal, the other pin of the wire  
connect to the DC power wire pin as the following picture showed. The other pin  
of adapter (power) wire connect to the alarm terminal.  
VIDEOINPUT  
* If the sensor or alarm you purchased is different from above instruction, please  
refer to the manual with the sensor/alarm.  
OPERATION  
The Factory has preset various functions as following list. If it can meet your usage  
requirement, please just follow our instructions to use the unit. If you want to  
change any pre-set function, please follow our instructions on next paragraph to  
change the setting to meet your particular requirement.  
The default setting on MAIN MENU  
Main Menu  
> CAMERA SELECT  
RECORD SELECT  
RECORD MODE  
RECORD FRAMERATE  
VIDEO QUALITY  
RECORD SCHEDULE  
SUB MENU  
1234  
1234  
EACH  
30  
NORMAL  
Default setting 0~24 record.  
HARD DRIVE SETUP  
SENSOR SETUP  
NETWORK SETUP  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION CONTINUED  
The default setting on the SUB-MENU  
SUB MENU  
(Default setting 111111)  
> PASSWORD CHANGE  
TIME SET  
2003/01/01 01:01:00  
FULL SCREEN BY SENSOR  
SEQUENT VIEW TIME  
OFF  
OFF  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
The default setting on the HARD DRIVE SETUP  
HARD DRIVE SET UP  
> OVERWRITE ENABLED  
MASTER HDD SIZE  
YES  
(Depends on HDD you choose)  
MASTER HDD USED  
MASTER HDD FORMAT  
SLAVE HDD SIZE  
SLAVE HDD USED  
SLAVE HDD FORMAT  
MB %  
(for format master HDD)  
(Depends on HDD you choose)  
MB %  
(for format master HDD)  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
The default setting on the SENSOR SETUP  
SENSOR SETUP  
> SENSOR RECORD TIME  
ALARM OUT TIME  
CHANNEL - 1  
CHANNEL - 2  
CHANNEL - 3  
30  
00 (OFF)  
Normal Open  
Normal Open  
Normal Open  
Normal Open  
CHANNEL - 4  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
The default setting on the NETWORK SETUP  
NETWORK SETUP  
> ACCEPT CLIENT  
MAC ADDRESS  
IP ADDRESS  
SUBNET MASK  
GATEWAY  
[YES]  
30.22.24.23.25.26  
192.168.001.090  
255.255.255.000  
192.168.991.245  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION CONTINUED  
Watch & View Control  
1.  
2.  
3.  
4.  
5.  
This View button controls FULL SCREEN display from camera 1.  
This View button controls FULL SCREEN display from camera 2.  
This View button controls FULL SCREEN display from camera 3.  
This View button controls FULL SCREEN display from camera 4.  
This View button controls QUAD SCREEN, displays all cameras.  
In the HARD DRIVE SETUP menu, the system will display the hard disk usage.  
Record Control  
1. When the red [RECORD] button is pressed, the recording process starts  
immediately. The recording channel indicator next to CH1, CH2, CH3, CH4  
will appear in the center of the screen to notify the user which camera is  
running during the period of recording.  
2. While the system is in recording mode, it will display the current writing hard  
driver ID on the bottom line, [M] or [S] ([M] = MASTER, [S] = SLAVE), and will  
show the percentage of hard disk recording capacity.  
3. If the system has detected hard disk is going to end and the user presses  
record button, the display will show warning message. During recording, if  
the system has detected hard disk recording capacity is going to end, it will  
notify the hard disk full warning by displaying the current hard disk ID in  
blinking.  
* Please make sure the Time is correct before recording. If no, please refer to  
Time Set section to change the time.  
Keylock Control  
Press the red [RECORD] button and hold it for 2 seconds or longer, the recording  
process starts immediately. But, the button has been locked. To stop the record-  
ing function, the user will be requested to key in the password.  
Playback Control  
The system allows the user select hard disk ID (Master or Slave), Event and  
Start time to play contents in SEARCH TIME menu.  
When the [] play button is pressed, the screen will display Hard driver ID  
(Master or Slave) and all events recorded in this hard drive (Max. 95 events  
will be recorded at each hard driver).  
To select hard drive for playback  
If you want to select hard drive other than shown on display for playback,  
press [] button then the [>] select mark will skip to hard drive select section,  
then press [SELECT] button to change hard drive ID, the screen will show  
other driver ID and event list.  
To playback the latest event  
Press the [] play button again the screen will show last recorded event.  
To select event for playback  
Press [] key or [] key to select the event, then press the [ ] play button,  
the screen will start to play the selected event till last event.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION CONTINUED  
REMARK  
The event logging maximum can record 95 events for each hard disk, but the  
screen can only show 7 events. If the events are more than 7 and the select  
mark stays on the 7th event, press [] key once will roll up the next event till the  
last event is shown. If the events are more than 95, the old recorded information  
will be stored in HDD too. The user can playback it by button in search time.  
To select playback by SEARCH TIME  
1. Press button to skip the select mark [>] to select hard driver section, then  
press the and button to move the ? cursor below the number back  
and forth. Then, use the SELECT button to change the numeric values of  
date & time.  
2. Press the [] play button the system will play the recorded video from the  
selected start time.  
3. You may use the View button (during playback) to select which camera you  
want to be displayed on the monitor. Full screen playback is available only  
when the camera record selection is in Each mode.  
4. To pause playback, press the ||key.  
5. During playback, if the user presses button, the system will skip 1200KB  
video data and decode one frame; the system repeats the skipping and  
decoding one frame till it meets the end of event recorded.  
6. Fast forward function will work in FFx2, FFx4, FFx8 cycle. During playback, if  
the user presses button, the playback mode will be played at FFx2  
(2 times speed) and if the user presses one more time, the playback mode  
will be played at FFx4 (4 times speed). If pressing one more time, the mode  
will be played at FFx8 (8 times speed). Press the play button will return to  
normal speed.  
7. After playback operation, press key for other function operation.  
CAUTION:  
A jumper setting on the main board may be used to convert the operation for-  
mat to PAL or NTSC to match the system of the display. The factory will preset as  
the importer s request. However, if you find that your color TV screen can t show  
color video, please check whether the jumper setting is matchable with the sys-  
tem of your monitor or not.  
MENU SETTING  
MAIN MENU SETTING  
Setting Operation Process  
1. Press key to stop all functions in operation.  
2. Press MENU key, the screen will display this menu.  
3. In the main menu, the > indicator will be shown on the screen right next to  
one of the ten different menu selections.  
4. Press key or key to choose the function to be changed on the menu.  
5. Press SELECT key to make changes in the selected option.  
6. Press MENU key to exit menu setting.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU SETTINGS  
Main Menu Setting  
Main Menu  
1234  
> CAMERA SELECT  
RECORD SELECT  
RECORD MODE  
RECORD FRAMERATE  
VIDEO QUALITY  
RECORD SCHEDULE  
SUB MENU  
1234  
EACH  
30  
NORMAL  
Default setting 0~24 record.  
HARD DRIVE SETUP  
SENSOR SETUP  
NETWORK SETUP  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
Camera Select  
1. When CAMERA SELECT option is selected, 4 different images from all  
cameras are initially displayed. (The default setting is 1234 all cameras on.)  
2. Use the view button on the front panel to select the camera for real-time  
viewing on the TV screen. CH 1 (Camera 1), CH 2 (Camera 2),  
CH 3 (Camera 3), CH 4 (Camera 4).  
3. You can also use the SELECT button for different combinations of camera  
viewing. For example,  
a). When you choose [----], all cameras will be disabled.  
b). When you choose [1234], all cameras will be activated.  
c). When choose [---4], only camera 4 will be activated.  
d). When you choose [12-4], camera 1,2 and 4 will be activated.  
* There are 16 different combinations of camera view for your choice.  
Record Select  
1. When you select RECORD SELECT , you may turn on or turn off the recording  
function of different channels (The default setting is 1234 all cameras on.).  
2. The selected camera channel on RECORD SELECT menu is same as CAMERA  
SELECT options.  
3. Please be reminded that only selected camera will record real-time events  
during the recording period.  
Record Mode  
1. There are two different record mode - EACH and QUAD to be selected.  
2. When you set EACH mode, you can view each image display in a single full  
screen by using the button on front panel of the DVR.  
3. When you set QUAD mode, you can see the images from the cameras in  
the quad screen which shows four sections on the single TV screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU SETTINGS  
Record Frame Rate  
1. When RECORD FRAME RATE is selected, you may choose the following  
recording frame rate - 30, 15, 10, 7, 5, 4, 3, 2 or 1 fps for recording.  
2. The higher the record frame rate is, the more natural the look will be  
displayed on the screen when you playback. The lower the record frame  
rate is, the more the capacity you can save on the hard disk driver.  
Video Quality  
When VIDEO QUALITY is selected, there are three different video quality  
LOW, NORMAL or HIGH resolution for your setting.  
The higher the video quality is, the more clear the image is when you  
playback. The lower the video quality is, the more the capacity you can  
save on the hard disk driver.  
Record Schedule  
You can change recording schedule during a day (24 hours period) by using this  
option. If the sensor device is attached to the DVR, it will add additional function  
to your recording.  
1. Use SELECT button to change the record mode.  
2. You may choose T for non-stop automatic recording.  
3. The selection, S is for sensor recording. It means that DVR starts recording  
only when sensor device is attached to the DVR and receive motion signal.  
4. The selection, - , means nothing will be recorded during this period.  
5. Press MENU button to return to the full Menu page.  
Sub Menu Setting:  
(When you select SUB MENU , the screen will display SUB MENU page.)  
SUB MENU  
> PASSWORD CHANGE  
TIME SET  
(Default setting 111111)  
2003/01/01 01:01:00  
FULL SCREEN BY SENSOR  
SEQUENT VIEW TIME  
OFF  
OFF  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
Password Change  
1. When you select PASSWORD CHANGE , a password input menu will replace  
the Sub Menu . (Initial Password: 111111)  
2. You will, then, be asked to input the following information:  
CURRENT PASSWORD: ------  
NEW PASSWORD: ------  
PASSWORD CONFIRM: ------  
3. You can use the view control button on the front panel to input the number:  
is 1,  
is 2,  
is 3,  
is 4,  
is 5.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU SETTINGS  
4. When the new password is accepted, the system will flash the following  
screen message: Password Change !!!  
5. The message will flash 5 times.  
6. Then, it will be back to the SUB MENU  
If the password is not accepted, you will receive a message to inform you:  
Password Incorrect , then return to the SUB MENU . You may try again by  
repeating the same steps.  
Time Set  
1. Below is a screen shot of the Time Menu screen, you can change  
time/date/hour/year by using TIME SET menu.  
TIME  
2005/01/01  
01:01:00  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
(This represents year/month/day and hour/minute/second)  
2. Use theand button on the front panel to move the ? cursor below the  
number back and forth. Then, use the SELECT button to change the numeric  
values of date & time.  
3. When you press the MENU button, your setting is memorized by the system.  
Full Screen by Sensor  
When FULL SCREEN BY SENSOR is selected, you can choose [ON] or OFF] this  
function. If you choose [ON], when sensor device is attached to the DVR  
and receive motion signal, the screen will display a single full screen of this  
area.  
Sequent View Time  
When SEQUENT VIEW TIME is selected, you can select sequent view time by  
02, 03, 04, 05, 06, 07, 08, 09, 10 seconds or [OFF] (= turn off the function).  
Hard Drive Setup  
(When you select HARD DRIVE SETUP , the screen will display HARD DRIVE  
SETUP page.)  
HARD DRIVE SET UP  
> OVERWRITE ENABLED  
MASTER HDD SIZE  
YES  
(Depends on HDD you choose)  
MB %  
MASTER HDD USED  
MASTER HDD FORMAT  
SLAVE HDD SIZE  
SLAVE HDD USED  
SLAVE HDD FORMAT  
(for format master HDD)  
(Depends on HDD you choose)  
MB %  
(for format master HDD)  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU SETTINGS  
1. Overwrite Enabled  
If you choose [YES], the recording will continue and overwrite previous  
recording when all hard disk driver capacity is full.  
If you choose [NO], the recording session stops when all hard disk driver  
capacity is full.  
2. Master HDD Size  
It shows the size of the Master hard disk driver installed in the DVR.  
3. Master HDD Used  
It shows the capacity used on the Master hard disk driver for recording.  
4. Master HDD Format  
If you format the hard disk driver, it will crease all the data recorded on the  
Master hard disk driver.  
5. Slave HDD Size  
It shows the size of the Slave hard disk driver installed in the DVR.  
6. Slave HDD Used  
It shows the capacity used on the Slave hard disk driver for recording.  
7. Slave HDD Format  
If you format the hard disk driver, it will crease all the data recorded on the  
Slave hard disk drive r.  
HDD Format  
1. When you select HDD FORMAT ,a password input will be requested on the  
screen: PASSWORD INPUT (6): - - - - - -  
2. Then, you will be prompted to input a password.  
3. When you key in the correct password, the message Password Correct will  
flash 3 times. Otherwise, the error message Password Incorrect will be  
displayed on the screen.  
Sensor Setup  
When you select Sensor Setup , the screen will display SENSOR SETUP page.)  
SENSOR SETUP  
> SENSOR RECORD TIME  
ALARM OUT TIME  
CHANNEL - 1  
CHANNEL - 2  
CHANNEL - 3  
30  
00 (OFF)  
Normal Open  
Normal Open  
Normal Open  
Normal Open  
CHANNEL - 4  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
Sensor Record Time  
When you select SENSOR RECORD TIME , the number indicates how long the  
recording lasts after the sensor detected the last motion in front of the  
sensor.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU SETTINGS  
Alarm Out Time  
When you select ALARM OUT TIME , the number indicates how long  
(in seconds) the alarm lasts after the sensor detected the motion signal.  
If you set CONT, the alarm will keep continuous when sensor detected the  
motion signal.  
If you set OFF , the alarm will not function when sensor detected the motion  
signal.  
Sensor Type Setup  
When you select SENSOR TYPE SETUP, you can select NOT INSTALLED,  
NORMAL OPEN type or NORMAL - CLOSE type sensor to make setting for  
each channel.  
In NORMAL-OPEN mode, if the connecting cable from sensor to DVR is cut  
off by an intruder, the sensor recording will stop.  
In NORMAL-CLOSE mode, if the cable connected to the sensor through DVR  
is cut off by an intruder, the sensor recording will start.  
NETWORK SETUP  
NETWORK SETUP  
> ACCEPT CLIENT  
MAC ADDRESS  
IP ADDRESS  
SUBNET MASK  
GATEWAY  
[YES]  
30.22.24.23.25.26  
192.168.001.090  
255.255.255.000  
192.168.991.245  
PRESS (< , >) THEN (SELECT)  
PRESS (MENU) TO EXIT  
(NOTE: THE NETWORK SETUP MENU IS USED ONLY FOR THE SYSTEM WITH OPTIONAL  
LAN INTERFACE. IF YOUR SYSTEM WITH BUILT-IN LAN INTERFACE, PLEASE REFER TO  
NETWORK MENU.)  
CAUTION:  
RESET (Initialization): To make the system reset, press ";" button 5 times in the nor-  
mal view mode. Be aware that all the information (Including password) will be  
lost. After resetting, the password will be set as the default value (111111).  
*After above setting process, press [MENU] button to go back to [MAIN MENU],  
then you can select other item for setting or press [MENU] button again to go  
back to View screen for recording function or operate the other function.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLE SHOOTING  
The power indicator is OFF on the DVR.  
1. Check and see if the AC power cord is connected properly.  
2. Check and see if the power outlet on the wall is working.  
3. Is the power outlet on the wall controlled by a wall switch? If it is, make  
sure the switch is on.  
The DVR can not be turned on.  
1. Check and see if the hard disk is correctly installed and properly locked.  
2. Please note the power cannot be entered if the key socket is not locked.  
Can not play the DVR  
1. Check the Hard disk and see if it is not locked or damaged.  
2. If the Hard Disk might be damaged, you can turn off the power of DVR and  
turn on the power again, the DVR will check the Hard Disk automatically.  
No Screen when TV or monitor is connected.  
1. Check and see if the Video output cord is connected to the screen properly.  
2. Check and see if two Hard Disks (HDD) setting (at the back of HDD) is  
correct. Please note that one should be set to Master position and the other  
one to Slave position.  
3. Please use 40G~120G byte Hard Disk (HDD) for the DVR so that the DVR  
can work properly.  
No color display on screen (Only black and white)  
1. Check whether the Camera and Display are working with color function.  
2. Check whether the Camera and Display are using same specification  
PAL or NTSC.  
3. A jumper setting on the main board may be used to convert the operation  
format to PAL or NTSC. Check whether the setting is matching the system of  
your monitor.  
The screen is unstable (jumping).  
1. Check and see if the video input cord is normal or not. If the cord is  
damaged or not connected properly, the screen will be unstable (jumping).  
2. Check the DVR setting, TV(Monitor) and Camera and see if they are the  
same type in PAL or NTSC. They must be same so that the DVR can  
work stably.  
Press [ MENU] button, but the MAIN MENU does not appear.  
Check the system and see whether it is in Record or View operation, press button  
to stop Record or View operation. Then, you can enter the MENU function.  
The Screen can display, but there is no video output from camera.  
1. Check and see if the camera wire is well connected, camera power is turn  
on and the camera can work normally.  
2. Check the MENU Setting list and see if the view camera is selected or not.  
3. Check View control Button and see if one of the cameras is selected to  
display full screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLE SHOOTING  
When Record does not work.  
Check the system and see whether it is in Play Mode, press button to stop  
Play Mode. Then, you can enter the RECORD function.  
When you forgot the password  
Please contact your distributor or engineer to solve this problem.  
To avoid this, have your password stored in a secure place away from  
the unit.  
Can’t stop Record function.  
The system is working with key lock function. If the system setting is with key  
lock while recording, you are requested to key in password to release key  
lock function. Then, it can stop recording.  
SPECIFICATIONS  
• Four channel video composite input (BNC conncoter)  
• Two channel video composite output RCA port  
• Wire remote control  
• Data and time: real time clock (rtc)  
• Recording mode : continue(t) sensor(s) not record(-)  
• Alarm output one channel  
• LAN connection interface (select)  
• Security: password protecion  
• Image compression and storage  
• Operating mode: quad/each  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For Further Assistance call:  
1.866.946.7828  
now you can see  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Singer Sewing Machine K49 User Manual
Sony Camcorder 4 114 858 121 User Manual
Sony DVD Recorder RDR VX410 User Manual
Sony Portable Speaker SRS PC21L User Manual
Sony Radio XDR S1 User Manual
Sony Security Camera SNC RH124 User Manual
Sony Universal Remote RM PP404 User Manual
SoundMax Home Theater System SM CDM1042 User Manual
Speco Technologies Computer Monitor VM 1005C User Manual
Star Micronics Printer TUP942 User Manual