Roland Drums V Tour TD 6KW User Guide
TD-6KW  
Owner’s Manual  
Thank you, and congratulations on your choice of the Roland Drum System TD-6KW.  
201a  
Before using this unit, carefully read the sections entitled: “USING THE UNIT  
SAFELY” and “IMPORTANT NOTES” (p. 2, p. 3). These sections provide important  
information concerning the proper operation of the unit. Additionally, in order to feel  
assured that you have gained a good grasp of every feature provided by your new  
unit, Owner’s manual should be read in its entirety. The manual should be saved  
and kept on hand as a convenient reference.  
* For the Snare (PDX-8) to function correctly, trigger parameters  
in the sound module TD-6V must be adjusted.  
202  
Copyright © 2006 ROLAND CORPORATION  
All rights reserved. No part of this publication may be reproduced in any form without the  
written permission of ROLAND CORPORATION.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT NOTES  
291a  
In addition to the items listed under “USING THE UNIT  
SAFELY” on page 2, please read and observe the  
following:  
Placement  
354a  
•
Do not expose the unit to direct sunlight, place it near  
devices that radiate heat, leave it inside an enclosed  
vehicle, or otherwise subject it to temperature extremes.  
Excessive heat can deform or discolor the unit.  
356  
•
Do not allow rubber, vinyl, or similar materials to remain  
on the unit for long periods of time. Such objects can  
discolor or otherwise harmfully affect the finish.  
Maintenance  
401a  
•
For everyday cleaning wipe the unit with a soft, dry cloth  
or one that has been slightly dampened with water. To  
remove stubborn dirt, use a cloth impregnated with a  
mild, non-abrasive detergent. Afterwards, be sure to wipe  
the unit thoroughly with a soft, dry cloth.  
402  
•
Never use benzine, thinners, alcohol or solvents of any  
kind, to avoid the possibility of discoloration and/or  
deformation.  
Additional Precautions  
553  
•
Use a reasonable amount of care when using the unit’s  
buttons, sliders, or other controls; and when using its jacks  
and connectors. Rough handling can lead to malfunctions.  
556  
•
When connecting / disconnecting all cables, grasp the  
connector itself—never pull on the cable. This way you  
will avoid causing shorts, or damage to the cable’s  
internal elements.  
558a  
•
To avoid disturbing your neighbors, try to keep the unit’s  
volume at reasonable levels. You may prefer to use  
headphones, so you do not need to be concerned about  
those around you (especially when it is late at night).  
558d  
•
This instrument is designed to minimize the extraneous  
sounds produced when it’s played. However, since sound  
vibrations can be transmitted through floors and walls to a  
greater degree than expected, take care not to allow these  
sounds to become a nuisance to neighbors, especially  
when performing at night and when using headphones.  
562  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Checking the Contents of the  
Box  
Drum Stand  
Assemble the Drum Stand.  
❑ TD-6V (Percussion Sound Module) x 1  
❑ KD-8 (Kick Trigger Pad) x 1  
❑ FD-8 (Hi-Hat Control Pedal) x 1  
❑ PDX-8 (V-Pad) x 1  
About the Stand, refer to the owner’s manual for the  
stand.  
❑ PD-8 (Pad) x 3  
❑ CY-5 (Cymbal Pad) x 1  
❑ CY-8 (Cymbal Pad) x 2  
❑ Connection Cables  
❑ Tuning Key x 1  
■ TD-6KW Owner’s Manual x 1  
• The tuning key is included in the FD-8 package.  
• The TD-6V Owner’s Manual is included in the TD-6V  
package.  
• This package does not include a kick pedal. Use with a  
commercially available kick pedal.  
• This package does not include the CY-5 attachment set  
for cymbal.  
962a  
* In the interest of product improvement, the specifications and/  
or appearance of this unit are subject to change without prior  
notice.  
TD-6V (Percussion Sound Module)  
Attach the mounting plate (included with the optional drum stand) to the TD-6V.  
Using the screws attached to the bottom panel, attach the holder so the unit is oriented as shown in the diagram.  
fig.TD-6V.e  
• To attach the stand holder, remove the four 8 mm  
screws (M5 x 8) from the bottom of the TD-6V and  
use them. Use of other screws may result in  
damage to the unit.  
928  
• When turning the unit upside-down, get a bunch  
of newspapers or magazines, and place them  
under the four corners or at both ends to prevent  
damage to the buttons and controls. Also, you  
should try to orient the unit so no buttons or  
controls get damaged.  
Narrow  
929  
• When turning the unit upside-down, handle with  
care to avoid dropping it, or allowing it to fall or  
tip over.  
Wide  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE UNIT SAFELY  
Adjusting the Head Tension  
PDX-8 (Snare)  
fig.PD-85.e_80  
Before using the pad, tighten the  
Tuning Bolt  
Hoop  
head so that the tension is rather firm.  
Rim Rubber  
Looseness in the head tension may result in problems such as  
Head Sensor  
failure of the PDX-8’s rim shots to sound or double triggering.  
Head  
Stand Fixing Screw  
Output Jack  
Striking the head when the head tension is loose may  
damage the sensor.  
Shell  
1. Use the tuning key to tighten the tuning bolts.  
Strike the head to check the feel and response.  
fig.Adjust.e  
Holder  
Loosen  
Tighten  
Rim Sensor  
add  
* Do NOT place your fingers inside the shell, as you may hurt  
yourself or cause damage to the PDX-8. Or when changing the  
head, do NOT touch any of the internal parts. Also, do not  
insert your fingers into the hole of the mounting bracket.  
fig.Stand.j  
Tighten each tuning bolt one by one, observing the  
numerical order shown in the diagram. Do not firmly  
tighten a single tuning bolt by itself. Doing so will make  
it impossible to tension the head evenly, and will cause  
malfunctions.  
fig.Bolt  
3
1
5
fig.Stand.j  
2
6
Head Sensor  
Rim Sensor  
4
2. Fine-tune the adjustment while continuing to  
check the pad feel and response.  
• On the PDX-8, adjusting the head tension affects only the  
head response, and does not change the pitch of the  
sound as it would on an acoustic drum.  
• Head tension may slacken with the passage of time.  
Readjust the tension as needed.  
Head Sensor  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
fig.RimShot.e  
USING THE UNIT SAFELY  
Attaching the Pad to a Stand  
Attach the PDX-8 to a pad mount of the stand.  
Be sure to tighten the stand fixing screw securel. If it  
remain loose, double triggering may occur.  
fig.Stand.e  
Suitable position  
for rim shots  
Tighten  
Player  
Loosen  
Rod  
Cross Stick  
Only strike the rim of the pad.  
Depending on the instrument assigned to the rim, you  
can play rim shots and/or cross stick sounds.  
fig.XStick.e  
Rim  
Playing Methods  
Head Shots  
Rim  
fig.HeadShot.e  
* To play the cross stick, be sure that you only strike the rim of  
the pad. Placing your hand on the head of the pad might  
prevent the cross stick sound from being played properly.  
Head  
For more on settings and tones, see the respective  
module’s owner’s manual.  
* Do not strike the hoop.  
If you hear a rim sound when you strike the head,  
decrease the “Rim Sens” value.  
Rim Shots  
fig.RimShot.e  
If you cannot get a rim sound even when you strike  
the rim hard, increase the “Rim Sens” value.  
Rim  
* To play rim shots, strike the rim in the area shown in the  
diagram.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE UNIT SAFELY  
Head Replacement  
Specifications  
PDX-8  
When the Head Should Be Replaced  
The head is an expendable item that eventually will wear out  
and need to be replaced. Replace the head when the following  
occurs:  
Head Size:  
Triggers:  
8 inches  
2 (Head, Rim)  
Dimensions:  
266 (W) x 326 (D) x 62 (H) mm  
10-1/2 (W) x 12-7/8 (D) x 2-1/2 (H) inches  
1.3 kg  
Slack portions remain in the head even when the head tension  
is properly adjusted.  
Weight:  
Option:  
2 lbs 14 oz  
Replacement heads (optional): MH-8 Mesh Head  
Mesh Head (MH-8)  
1. Remove all tuning bolts from the PDX-8.  
* The Rim rubber is one component that eventually wears out  
(the more so if numerous rim shots are performed), and will  
require replacement. Rim shots may not be performed correctly  
when the rim rubber is worn out. If this occurs, replace the rim  
rubber. Consult Roland Service for more on replacing the rim  
rubber.  
fig.Replace.e  
Loosen  
Tighten  
Tuning Key  
Tuning Bolt  
add  
* Due to the nature of the materials used in the sensor, changes  
in room temperature may affect the sensitivity of the sensor.  
Hoop  
Head  
Sensor  
Hoop’s Rubber  
Portion  
Shell  
Do not apply excessive force to the sensor located under  
the head. Doing so can interfere with accurate detection,  
and may damage it.  
2. Remove the hoop.  
3. Remove the old head.  
4. Place the new head on the shell.  
5. Place the hoop onto the head.  
6. Attach the tuning bolts to the hoop and shell.  
7. Next, adjust the tension of the head. Refer to  
“Adjusting the Head Tension” (p. 5).  
Do not firmly tighten a single tuning bolt by itself. Doing  
so will make it impossible to tension the head evenly, and  
will cause malfunctions.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
USING THE UNIT SAFELY  
Playing the PD-8  
PD-8 (Tom)  
fig.PD-HR.e  
fig.PD-8.e  
Head Shot  
Rim Shot  
Stand Fixing Screw  
Head  
Head  
Head  
Rim  
To play the sound assigned to the head, hit only the head.  
To play a rim shot, you must strike both the head and the  
rim of the pad simultaneously.  
Stand Fixing Screw  
Output Jack  
Specifications  
PD-8  
Pad Size:  
8.5 inches  
Triggers:  
2 (Head, Rim)  
Attaching the Pad to a Stand  
Dimensions:  
226 (W) x 280 (D) x 54 (H) mm  
Attach the PDX-8 to a pad mount of the stand.  
fig.PD-Set.e  
8-15/16 (W) x 11-1/16 (W) x 2-1/8 (H) inches  
Weight:  
1.2 kg  
Tighten  
2 lbs 11 oz  
Loosen  
Rod  
Pass the rod through the pipe that is inside the holder.  
When attaching the PD-8s to the mounts, be sure to  
tighten the stand fixing screws securely. If any of them  
remain loose, the pad could fall off.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Mount the CY-5 so it fits the lower clutch as  
USING THE UNIT SAFELY  
shown below.  
CY-5 (Hi-Hat)  
fig.CY-8.e  
Pad Face  
Bow Portion  
Edge Portion  
Projection (Be sure to  
orient it correctly)  
Output Jack  
Making the Settings  
3. Place the clutch felt (S), and while applying  
some pressure, mount the upper clutch as  
shown.  
When mounting the CY-5 on an L-Rod (pad mount),  
use ONLY the attachment set as shown below.  
Afterwards, you can adjust the upper clutch to have the  
movement you desire. If it is too loose, double triggering  
may occur.  
Upper Clutch  
Be sure the ROLAND logo is on the opposite side of the  
playing area.  
Clutch Felt (S)  
Apply pressure  
Tighten the bolt with  
a tuning key.  
Clutch Felt (L)  
Lower Clutch  
1. Mounting the lower clutch and the clutch felt  
Specifications  
(L).  
CY-5  
Align the notched section as shown below. Then place the  
clutch felt (L) so it fits securely.  
Size:  
10 inches  
Triggers:  
Dimensions:  
2 (Bow, Edge)  
246 (W) x 246 (D) x 45 (H) mm  
9-11/16 (W) x 9-11/16 (D) x 1-13/16 (H)  
inches  
Notch  
(Be sure to  
orient it correctly)  
Weight:  
380 g  
Tighten the bolt with  
a tuning key.  
14 oz (without attachment)  
Attachment Set for Hi-Hat (Upper Clutch,  
Lower Clutch, Clutch Felt (L), Clutch Felt (S))  
Accessories:  
add  
* Continuous playing may cause dis-coloration of the pad, but  
this will not affect the Pad's function.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE UNIT SAFELY  
Playing the CY-8  
CY-8 (Crash Cymbal/Ride Cymbal)  
fig.CY-8.e  
Bow Shot  
This is the most common playing method, playing the pad  
face of the cymbal. It corresponds to the sound of the “head-  
side” of the connected trigger input.  
Pad Face  
Bow Portion  
Edge Portion  
fig.CY-Bow.e  
Bow  
Output Jack  
Edge Shot  
This playing method involves striking the edge with the  
shoulder of the stick. It corresponds to the sound of the “rim-  
side” of the connected trigger input.  
* To make use of edge shot, you’ll need to connect to a trigger  
input jack on the percussion sound module that accommodates  
Attaching the Cymbal Pad to a Stand  
rim shots.  
fig.CY-Edge.e  
1. Use a tuning key to tighten the stopper bolt.  
Edge  
The stopper keeps the cymbal pad from turning, and  
prevents the cables from catching or getting tangled on  
the stand.  
fig.CY-Set01.e  
Stopper  
(Be sure to  
Tighten the bolt with  
a tuning key.  
orient it correctly)  
Choking  
Choking (pinching) the cymbal’s edge with the hand  
immediately after hitting the cymbal makes the sound stop.  
* To make use of choking play techniques, you’ll need to connect  
to a trigger input jack on the percussion sound module that  
2. Attach the CY-8 so the Roland logo is  
positioned on the opposite side of the playing  
area.  
accommodates rim shots.  
fig.CY-Choke  
3. Tighten the wing nut to obtain the desired  
movement.  
Use the included felt washer and the wing nut.  
fig.CY-Set02.e  
Wing Nut  
Specifications  
Felt Washer  
CY-8  
Size:  
12 inches  
Triggers:  
Dimensions:  
2 (Bow, Edge)  
290 (W) x 295 (D) x 47 (H) mm  
11-7/16 (W) x 11-5/8 (D) x 1-7/8 (H) inches  
650 g / 1 lb 7 oz  
Weight:  
Accessories:  
Wing Nut, Felt Washer, Stopper  
Double sounding may occur if the wing nut is loose.  
* Continuous playing may cause dis-coloration of the pad, but  
this will not affect the Pad's function.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE UNIT SAFELY  
Using the FD-8  
FD-8 (Hi-Hat Control Pedal)  
Using the FD-8, you can control the opening and closing of the  
hi-hat sound.  
fig.FD-8.e  
Adjusting the Travel of the Pedal  
Loosen the nut with a tuning key.  
After adjusting, tighten the nut.  
Open Hi-Hat  
Strike the hi-hat without pressing the pedal  
deep  
Shift the Arm  
Half Open Hi-Hat  
Strike the hi-hat with the pedal pressed half-way  
shallow  
Closed Hi-Hat  
Pedal Plate  
Anchor Bolt  
Strike the hi-hat with the pedal pressed  
Foot Closed  
Completely press down the pedal  
Control Out Jack  
Foot Open  
Press the pedal and then immediately release it  
Attaching the Anchor Bolts (When Using on the Carpet)  
Anchor Bolt  
Spring for  
the Anchor Bolt  
The volume of the Foot Closed sound can be adjusted  
separately (TD-6V Owner’s Manual; p. 66).  
• Connect the FD-8 to the TD-6V before turning on the  
power.  
• The tips of the anchor bolts are sharp. Handle with care.  
• When using on flooring, the anchor bolts may damage  
the floor. Do not attach the anchor bolts.  
• Do NOT press the pedal when turning on the power.  
• When the FD-8 is not going to be used for a long period  
of time, move and fix the arm, allowing longer travel for  
the pedal.  
Specifications  
FD-8  
• To avoid damage, do not leave the FD-8 for extended  
periods of time with the pedal plate depressed.  
Dimensions:  
Weight:  
130 (W) x 396 (D) x 103 (H) mm  
5-1/8 (W) x 15-5/8 (D) x 4-1/16 (H) inches  
1.3 kg  
2 lbs 14 oz  
Tuning Key  
Accessory:  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Use a tuning key to tighten the screws removed  
USING THE UNIT SAFELY  
in Step 1 so that the stand is firmly secured.  
fig.KD-Assy03  
KD-8 (Kick)  
fig.KD-8.e  
Output Jack  
Head  
Stand  
Anchor Bolt  
4. Attach the kick pedal.  
Foot Plate  
Position the beater so that it strikes the center of the head,  
then secure the kick pedal and KD-8 firmly in place.  
fig.KD-Assy04.e  
Making the Settings  
Beater  
1. Remove the screws attached to the reverse side  
of the KD-8’s trigger.  
fig.KD-Assy01  
Install the kick pedal securely.  
Adjusting the Foot Plate Height  
Depending on your kick pedal, it can be unstable when you  
attach it to the KD-8. Be sure to adjust the foot plate height so  
that the entire bottom surface of the pedal is attached to the  
floor.  
fig.KD-Assy05.e  
2. Pull out the stand in the direction indicated by  
the arrow until it is fully extended.  
fig.KD-Assy02  
Beater  
Commercially Available Kick Pedal  
* Adjust the height so that the entire pedal comes  
into contact with the floor.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Loosen the stand’s anchor bolts and remove  
the foot plate.  
fig.KD-Assy06  
Adjusting the AnchUoSIrNBGoTlHtsE UNIT SAFELY  
When using the kick pedal on a carpet or similar surface,  
adjust the anchor bolts so their tips protrude from the plate  
and secure the pedal in place; this will make it easier to use the  
kick pedal.  
However, when used on flooring, the anchor bolts may  
damage the floor. Adjust the anchor bolts correctly.  
fig.KD-Anchor.e  
Adjusting the Anchor Bolts  
When Using on the Carpet  
When using on the Floor  
The tips of the anchor bolts are sharp. Handle with care.  
2. Set the kick pedal so that the entire bottom  
surface is attached to the floor.  
When Using a Twin Pedal  
fig.KD-Pedal1  
3. In most cases, the stand becomes somewhat  
Position the two beaters  
floated. Tighten the anchor bolts securely there  
equally apart from the center  
of the pad as shown in the  
figure at left. If one of the  
beater is further away from the  
center than the other, the  
to fix the stand and foot plate.  
fig.KD-Assy07.e  
This hight will vary depending  
on your kick pedal.  
sound from the further beater  
will be lower in volume, or  
will not sound as desired.  
fig.KD-Pedal2  
Using a twin pedal will result  
in lower sensitivity as  
compared to when a single  
pedal is used. Raise the  
sensitivity on the sound  
module.  
• Install the kick pedal securely.  
• Take care not to pinch your fingers.  
• The tips of the anchor bolts are sharp. Handle with care.  
• When moving the setup, be sure to remove the screws  
and fold the stand. Transporting the KD-8 while it  
remains open may subject the stand to excessive strain  
and result in damage to the stand.  
Specifications  
KD-8  
Dimensions:  
Weight:  
272 (W) x 260 (D) x 405 (H) mm  
10-3/4 (W) x 10-1/4 (D) x 16 (H) inches  
2.9 kg  
6 lbs 7 oz  
Screws  
Accessories:  
* Continuous playing may cause dis-coloration of the pad, but  
this will not affect the Pad's function.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
.
USING THE UNIT SAFELY  
Assemble the “TD-6KW”  
921  
Using the provided cables, connect the pads.  
Connect the L-shaped plugs of the included cables to the pads.  
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power  
on all devices before making any connections.  
fig.Setting1.e  
HH SNR KIK  
HHC RD  
CR1 T3 T2 T1  
CR1  
RD  
CY-8  
CY-8  
T1  
T2  
PD-8  
HH  
PD-8  
CY-5  
TD-6V  
PDX-8  
T3  
PD-8  
SNR  
KD-8  
KIK  
HHC  
FD-8  
fig.Label  
1. Insert the plugs of connecting cables into the TRIGGER INPUTS jacks on the  
rear of the TD-6V.  
2. Insert the L-sharped plugs into the TRIGGER OUTPUTS jacks of the pads.  
SNR  
* When you connect the cables, please refer to the marking label that is attached on both edge of the cables.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
.
USING THE UNIT SAFELY  
Trigger Settings for the TD-6V  
For the Snare (PDX-8) to function correctly, trigger parameters in the sound module  
TD-6V must be adjusted.  
For more detailed informations, refer to the TD-6KV Owner’s Manual.  
Adding the Optional Pads to the TD-6KW  
When adding the new pad, use trigger input 10 (CRASH2).  
With the optional cable (PCS-31L) or a standard insert cable, you can connect two pads to the triger inputs 5/6  
(TOM2/AUX) and 7/8 (TOM3/4). You can use up to 11 pads at the same time.  
*
When connecting two pads to 1 input (5/6 or 7/8), rim shots are not be possible. For more information, refer to TD-6V  
Owner’s Manual p.70.  
Examples  
Adding a Cymbal  
TD-6V Rear Panel  
Adding the CY-8 or the CY-5 for a  
2nd Crash or a Splash Cymbal. For  
mounting, use the Cymbal Mount  
MDY-10U.  
Adding a Tom  
Adding the PD-8 for a 2nd floor  
PCS-31L  
tom.  
Connect the PD-8 to the trigger  
input 10 (CRASH2).  
With the optional cable (PCS-31L),  
you can also connect two PD-8s to  
the trigger input 7/8 (TOM3/4).  
For mounting, use the Pad Mount  
MDH-10U.  
PD-8  
PD-8  
Options  
Kick Trigger Pad:  
KD-8, KD-7  
KD-85, KD-120  
PD-8  
V-Kick Trigger Pad:  
Dual Trigger Pad:  
V-Pad:  
PDX-8, PD-85, PD-105, PD-125  
CY-8, CY-5  
Cymbal Pad:  
V-Cymbal:  
CY-12R/C, CY-14C, CY-15R  
Pad Mount:  
MDH-10U  
MDY-10U  
Cymbal Mount:  
Connection Cable:  
PCS-31L  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Information  
When you need repair service, call your nearest Roland Service Center or authorized Roland  
distributor in your country as shown below.  
PHILIPPINES  
COSTA RICA  
TRINIDAD  
NORWAY  
JORDAN  
AFRICA  
G.A. Yupangco & Co. Inc.  
339 Gil J. Puyat Avenue  
Makati, Metro Manila 1200,  
PHILIPPINES  
JUAN Bansbach Instrumentos  
AMR Ltd  
Roland Scandinavia Avd.  
MUSIC HOUSE CO. LTD.  
Ground Floor  
Musicales  
Kontor Norge  
FREDDY FOR MUSIC  
P. O. Box 922846  
Amman 11192 JORDAN  
TEL: (06) 5692696  
EGYPT  
Al Fanny Trading Office  
9, EBN Hagar A1 Askalany  
Street,  
ARD E1 Golf, Heliopolis,  
Cairo 11341, EGYPT  
TEL: 20-2-417-1828  
Maritime Plaza  
Barataria Trinidad W.I.  
TEL: (868) 638 6385  
Ave.1. Calle 11, Apartado 10237,  
San Jose, COSTA RICA  
TEL: 258-0211  
Lilleakerveien 2 Postboks 95  
Lilleaker N-0216 Oslo  
NORWAY  
TEL: (02) 899 9801  
TEL: 2273 0074  
SINGAPORE  
SWEE LEE MUSIC  
COMPANY PTE. LTD.  
150 Sims Drive,  
SINGAPORE 387381  
TEL: 6846-3676  
URUGUAY  
Todo Musica S.A.  
Francisco Acuna de Figueroa  
1771  
C.P.: 11.800  
Montevideo, URUGUAY  
TEL: (02) 924-2335  
CURACAO  
Zeelandia Music Center Inc.  
Orionweg 30  
Curacao, Netherland Antilles  
TEL:(305)5926866  
KUWAIT  
EASA HUSAIN AL-YOUSIFI  
& SONS CO.  
Abdullah Salem Street,  
Safat, KUWAIT  
TEL: 243-6399  
POLAND  
MX MUSIC SP.Z.O.O.  
UL. Gibraltarska 4.  
PL-03664 Warszawa POLAND  
TEL: (022) 679 44 19  
REUNION  
Maison FO - YAM Marcel  
25 Rue Jules Hermann,  
Chaudron - BP79 97 491  
Ste Clotilde Cedex,  
DOMINICAN REPUBLIC  
Instrumentos Fernando Giraldez  
Calle Proyecto Central No.3  
Ens.La Esperilla  
Santo Domingo,  
Dominican Republic  
TEL:(809) 683 0305  
TAIWAN  
ROLAND TAIWAN  
ENTERPRISE CO., LTD.  
Room 5, 9fl. No. 112 Chung  
Shan N.Road Sec.2, Taipei,  
TAIWAN, R.O.C.  
PORTUGAL  
Roland Iberia, S.L.  
Portugal Office  
Cais das Pedras, 8/9-1 Dto  
4050-465, Porto, PORTUGAL  
TEL: 22 608 00 60  
LEBANON  
Chahine S.A.L.  
Gerge Zeidan St., Chahine  
Bldg., Achrafieh, P.O.Box: 16-  
5857  
Beirut, LEBANON  
TEL: (01) 20-1441  
VENEZUELA  
Instrumentos Musicales  
Allegro,C.A.  
Av.las industrias edf.Guitar  
REUNION ISLAND  
TEL: (0262) 218-429  
SOUTH AFRICA  
That Other Music Shop(PTY)Ltd.  
11 Melle St., Braamfontein,  
Johannesbourg,  
SOUTH AFRICA  
TEL: (011) 403 4105  
import  
#7 zona Industrial de Turumo  
Caracas, Venezuela  
TEL: (212) 244-1122  
TEL: (02) 2561 3339  
ROMANIA  
FBS LINES  
Piata Libertatii 1,  
535500 Gheorgheni,  
ROMANIA  
ECUADOR  
Mas Musika  
Rumichaca 822 y Zaruma  
Guayaquil - Ecuador  
THAILAND  
OMAN  
Theera Music Co. , Ltd.  
330 Soi Verng NakornKasem,  
New Road, Sumpantawongse,  
Bangkok 10100, THAILAND  
TEL: (02) 224-8821  
TALENTZ CENTRE L.L.C.  
Malatan House No.1  
Al Noor Street, Ruwi  
SULTANATE OF OMAN  
TEL: 2478 3443  
FAX: (011) 403 1234  
EUROPE  
TEL:(593-4)2302364  
TEL: (266) 364 609  
Paul Bothner(PTY)Ltd.  
Royal Cape Park, Unit 24  
Londonderry Road, Ottery 7800  
Cape Town, SOUTH AFRICA  
TEL: (021) 799 4900  
EL SALVADOR  
OMNI MUSIC  
75 Avenida Norte y Final  
Alameda Juan Pablo II,  
Edificio No.4010 San Salvador,  
EL SALVADOR  
AUSTRIA  
Roland Elektronische  
Musikinstrumente HmbH.  
RUSSIA  
MuTek  
Dorozhnaya ul.3,korp.6  
117 545 Moscow, RUSSIA  
TEL: (095) 981-4967  
VIETNAM  
SAIGON MUSIC  
DISTRIBUTOR  
(TAN DINH MUSIC)  
138 Tran Quang Khai Street  
Dist. 1, Ho Chi Minh City  
VIETNAM  
QATAR  
Al Emadi Co. (Badie Studio &  
Stores)  
P.O. Box 62, Doha, QATAR  
Austrian Office  
Eduard-Bodem-Gasse 8,  
A-6020 Innsbruck, AUSTRIA  
TEL: (0512) 26 44 260  
TEL: 262-0788  
TEL: 4423-554  
SPAIN  
ASIA  
Roland Iberia, S.L.  
Paseo García Faria, 33-35  
08005 Barcelona SPAIN  
TEL: 93 493 91 00  
GUATEMALA  
SAUDI ARABIA  
aDawliah Universal  
Electronics APL  
Corniche Road, Aldossary  
Bldg., 1st Floor, Alkhobar,  
SAUDI ARABIA  
BELGIUM/FRANCE/  
HOLLAND/  
LUXEMBOURG  
Roland Central Europe N.V.  
Houtstraat 3, B-2260, Oevel  
(Westerlo) BELGIUM  
CHINA  
Roland Shanghai Electronics  
Co.,Ltd.  
5F. No.1500 Pingliang Road  
Shanghai 200090, CHINA  
TEL: (021) 5580-0800  
Casa Instrumental  
Calzada Roosevelt 34-01,zona 11  
Ciudad de Guatemala  
Guatemala  
TEL: (08) 848-4068  
SWEDEN  
Roland Scandinavia A/S  
SWEDISH SALES OFFICE  
Danvik Center 28, 2 tr.  
S-131 30 Nacka SWEDEN  
TEL: (0)8 702 00 20  
TEL:(502) 599-2888  
AUSTRALIA/  
NEW ZEALAND  
AUSTRALIA/  
NEW ZEALAND  
Roland Corporation  
Australia Pty.,Ltd.  
38 Campbell Avenue  
Dee Why West. NSW 2099  
AUSTRALIA  
HONDURAS  
Almacen Pajaro Azul S.A. de C.V.  
BO.Paz Barahona  
3 Ave.11 Calle S.O  
San Pedro Sula, Honduras  
TEL: (504) 553-2029  
P.O.Box 2154, Alkhobar 31952  
SAUDI ARABIA  
TEL: (03) 898 2081  
TEL: (014) 575811  
Roland Shanghai Electronics  
Co.,Ltd.  
(BEIJING OFFICE)  
10F. No.18 3 Section Anhuaxili  
Chaoyang District Beijing  
100011 CHINA  
CZECH REP.  
K-AUDIO  
Kardasovska 626.  
CZ-198 00 Praha 9,  
CZECH REP.  
SYRIA  
Technical Light & Sound  
Center  
Rawda, Abdul Qader Jazairi St.  
Bldg. No. 21, P.O.BOX 13520,  
Damascus, SYRIA  
SWITZERLAND  
Roland (Switzerland) AG  
Landstrasse 5, Postfach,  
CH-4452 Itingen,  
SWITZERLAND  
TEL: (061) 927-8383  
MARTINIQUE  
Musique & Son  
Z.I.Les Mangle  
97232 Le Lamantin  
Martinique F.W.I.  
TEL: 596 596 426860  
TEL: (2) 666 10529  
TEL: (010) 6426-5050  
DENMARK  
Roland Shanghai Electronics  
Co.,Ltd.  
(GUANGZHOU OFFICE)  
2/F., No.30 Si You Nan Er Jie  
Yi Xiang, Wu Yang Xin Cheng,  
Guangzhou 510600, CHINA  
TEL: (020) 8736-0428  
Roland Scandinavia A/S  
Nordhavnsvej 7, Postbox 880,  
DK-2100 Copenhagen  
DENMARK  
TEL: (011) 223-5384  
For Australia  
UKRAINE  
TIC-TAC  
Mira Str. 19/108  
P.O. Box 180  
295400 Munkachevo,  
UKRAINE  
TEL: (03131) 414-40  
Tel: (02) 9982 8266  
For New Zealand  
Tel: (09) 3098 715  
TURKEY  
ZUHAL DIS TICARET A.S.  
Galip Dede Cad. No.37  
Beyoglu - Istanbul / TURKEY  
TEL: (0212) 249 85 10  
Gigamusic SARL  
10 Rte De La Folie  
97200 Fort De France  
Martinique F.W.I.  
TEL: 596 596 715222  
TEL: 3916 6200  
FINLAND  
Roland Scandinavia As, Filial  
Finland  
Elannontie 5  
FIN-01510 Vantaa, FINLAND  
TEL: (0)9 68 24 020  
CENTRAL/LATIN  
AMERICA  
HONG KONG  
Tom Lee Music Co., Ltd.  
Service Division  
22-32 Pun Shan Street, Tsuen  
Wan, New Territories,  
HONG KONG  
U.A.E.  
Zak Electronics & Musical  
Instruments Co. L.L.C.  
Zabeel Road, Al Sherooq Bldg.,  
No. 14, Grand Floor, Dubai,  
U.A.E.  
UNITED KINGDOM  
MEXICO  
Roland (U.K.) Ltd.  
Atlantic Close, Swansea  
Enterprise Park, SWANSEA  
SA7 9FJ,  
Casa Veerkamp, s.a. de c.v.  
Av. Toluca No. 323, Col. Olivar  
de los Padres 01780 Mexico  
D.F. MEXICO  
ARGENTINA  
Instrumentos Musicales S.A.  
Av.Santa Fe 2055  
(1123) Buenos Aires  
ARGENTINA  
TEL: (011) 4508-2700  
GERMANY  
Roland Elektronische  
Musikinstrumente HmbH.  
Oststrasse 96, 22844  
Norderstedt, GERMANY  
TEL: (040) 52 60090  
TEL: 2415 0911  
TEL: (04) 3360715  
UNITED KINGDOM  
TEL: (01792) 702701  
TEL: (55) 5668-6699  
Parsons Music Ltd.  
NICARAGUA  
Bansbach Instrumentos  
Musicales Nicaragua  
Altamira D'Este Calle Principal  
de la Farmacia 5ta.Avenida  
1 Cuadra al Lago.#503  
Managua, Nicaragua  
8th Floor, Railway Plaza, 39  
Chatham Road South, T.S.T,  
Kowloon, HONG KONG  
TEL: 2333 1863  
BARBADOS  
NORTH AMERICA  
A&B Music Supplies LTD  
12 Webster Industrial Park  
Wildey, St.Michael, Barbados  
TEL: (246)430-1100  
MIDDLE EAST  
GREECE  
STOLLAS S.A.  
Music Sound Light  
155, New National Road  
Patras 26442, GREECE  
TEL: 2610 435400  
CANADA  
Roland Canada Music Ltd.  
(Head Office)  
5480 Parkwood Way  
Richmond B. C., V6V 2M4  
CANADA  
INDIA  
Rivera Digitec (India) Pvt. Ltd.  
409, Nirman Kendra  
Mahalaxmi Flats Compound  
Off. Dr. Edwin Moses Road,  
Mumbai-400011, INDIA  
TEL: (022) 2493 9051  
BAHRAIN  
Moon Stores  
No.16, Bab Al Bahrain Avenue,  
P.O.Box 247, Manama 304,  
State of BAHRAIN  
BRAZIL  
Roland Brasil Ltda.  
Rua San Jose, 780 Sala B  
Parque Industrial San Jose  
Cotia - Sao Paulo - SP, BRAZIL  
TEL: (011) 4615 5666  
TEL: (505)277-2557  
PANAMA  
TEL: (604) 270 6626  
SUPRO MUNDIAL, S.A.  
Boulevard Andrews, Albrook,  
Panama City, REP. DE  
PANAMA  
TEL: 17 211 005  
HUNGARY  
Roland East Europe Ltd.  
Warehouse Area ‘DEPO’ Pf.83  
H-2046 Torokbalint,  
HUNGARY  
CYPRUS  
Radex Sound Equipment Ltd.  
17, Diagorou Street, Nicosia,  
CYPRUS  
Roland Canada Music Ltd.  
(Toronto Office)  
170 Admiral Boulevard  
Mississauga On L5T 2N6  
CANADA  
INDONESIA  
PT Citra IntiRama  
J1. Cideng Timur No. 15J-150  
Jakarta Pusat  
INDONESIA  
TEL: (021) 6324170  
CHILE  
Comercial Fancy II S.A.  
Rut.: 96.919.420-1  
Nataniel Cox #739, 4th Floor  
Santiago - Centro, CHILE  
TEL: (02) 688-9540  
TEL: 315-0101  
TEL: (23) 511011  
PARAGUAY  
Distribuidora De  
Instrumentos Musicales  
J.E. Olear y ESQ. Manduvira  
Asuncion PARAGUAY  
TEL: (595) 21 492147  
TEL: (022) 66-9426  
TEL: (905) 362 9707  
IRELAND  
Roland Ireland  
G2 Calmount Park, Calmount  
Avenue, Dublin 12  
Republic of IRELAND  
TEL: (01) 4294444  
IRAN  
MOCO INC.  
No.41 Nike St., Dr.Shariyati Ave.,  
Roberoye Cerahe Mirdamad  
Tehran, IRAN  
U. S. A.  
KOREA  
Roland Corporation U.S.  
5100 S. Eastern Avenue  
Los Angeles, CA 90040-2938,  
U. S. A.  
Cosmos Corporation  
1461-9, Seocho-Dong,  
Seocho Ku, Seoul, KOREA  
TEL: (02) 3486-8855  
COLOMBIA  
Centro Musical Ltda.  
Cra 43 B No 25 A 41 Bododega 9  
Medellin, Colombia  
PERU  
Audionet  
Distribuciones Musicales SAC  
Juan Fanning 530  
Miraflores  
TEL: (021) 285-4169  
TEL: (323) 890 3700  
ITALY  
Roland Italy S. p. A.  
Viale delle Industrie 8,  
20020 Arese, Milano, ITALY  
TEL: (02) 937-78300  
ISRAEL  
Halilit P. Greenspoon & Sons  
Ltd.  
8 Retzif Ha'aliya Hashnya St.  
Tel-Aviv-Yafo ISRAEL  
TEL: (03) 6823666  
TEL: (574)3812529  
MALAYSIA  
Roland Asia Pacific Sdn. Bhd.  
45-1, Block C2, Jalan PJU 1/39,  
Dataran Prima, 47301 Petaling  
Jaya, Selangor, MALAYSIA  
TEL: (03) 7805-3263  
Lima - Peru  
TEL: (511) 4461388  
As of December 10, 2005 (ROLAND)  
04234201  
2PR  
Download from Www.Somanuals.com. All Manuals Search And Download.  

PYLE Audio Speaker PHSP10TA User Guide
Ramsey Electronics Stereo System RXD433 User Guide
RedMax Chainsaw GZ400 User Guide
Reebok Fitness Treadmill RBTL18910 User Guide
Roadmaster Speaker RS525 User Guide
Samsung Cell Phone VM A680 User Guide
Samsung Home Security System SDC8340BU User Guide
Sanyo CD Player CDP 244 User Guide
Sanyo Refrigerator MBR 1404G User Guide
Savin Printer 3740 User Guide