OPERATOR’S MANUAL
10 in. TABLE SAW
R4516
Your new table saw has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this
product.
Thank you for buying a RIDGID® product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SECURE WORK. Use a featherboard to hold work when
practical. It’s safer than using your hand and frees both
hands to operate tool.
DON’T OVERREACH. Keep proper footing and
READ ALL INSTRUCTIONS
balance at all times.
KNOW YOUR POWER TOOL. Read the operator’s
manual carefully. Learn the saw’s applications and
limitationsaswellasthespecificpotentialhazardsrelated
to this tool.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
andcleanforbetterandsaferperformance.Followinstruc-
tions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES. For example, pipes, radiators, ranges,
refrigerator enclosures.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
KEEP GUARDS IN PLACE and in good working order.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habitofcheckingtoseethatkeysandadjustingwrenches
are removed from tool before turning it on.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
KEEPWORKAREACLEAN.Clutteredareasandbenches
invite accidents. DO NOT leave tools or pieces of wood
on the saw while it is in operation.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefullycheckedtodeterminethatitwilloperateproperly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visi-
tors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks and
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
master switches, or by removing starter keys.
DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
NEVERLEAVETOOLRUNNINGUNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
PROTECT YOUR LUNGS. Wear a face or dust mask if
USETHEPROPERExTENSIONCORD. Makesureyour
extensioncordisingoodcondition.Useonlyacordheavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 14 is recommended for an extension
cord 25 feet or less in length. If in doubt, use the next
heaviergauge.Thesmallerthegaugenumber,theheavier
the cord.
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never yank cord to disconnect
fromreceptacle.Keepcordawayfromheat,oil,andsharp
edges.
WHEN OPERATING A POWER TOOL OUTSIDE, USE
ANOUTDOORExTENSIONCORDMARKED“W-A”OR
“W”. These cords are rated for outdoor use and reduce
the risk of electric shock.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
ALWAYS KEEP THE BLADE GUARD AND SPREADER
(SPLITTER) IN PLACE and in working order.
KEEP BLADES CLEAN, SHARP, AND WITH
SUFFICIENT SET. Sharp blades minimize stalling
and kickback.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
STAY ALERT AND ExERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath
work or around or over the blade while blade is rotating.
Do not attempt to remove cut material when blade is
moving.
BLADE COASTS AFTER BEING TURNED OFF.
NEVER USE IN AN ExPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
INSPECT TOOL CORDS PERIODICALLY. If dam-
aged, have repaired by a qualified service technician at
anauthorizedservicefacility.Theconductorwithinsulation
havinganoutersurfacethatisgreenwithorwithoutyellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
INSPECT ExTENSION CORDS PERIODICALLY and
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole elec-
trical receptacle.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool's plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of your saw is 10 in. (254 mm).
BEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
BE SURE BLADE PATH IS FREE OF NAILS. Inspect for
and remove all nails from lumber before cutting.
NEVER TOUCH BLADE or other moving parts during
use.
NEVER START A TOOL WHEN ANY ROTATING COM-
PONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHENSERVICINGuseonlyidenticalreplacementparts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
DOUBLE CHECK ALL SETUPS. Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
SPECIFIC SAFETY RULES
FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG
STAND at approximately waist height.
Through-sawing operations are those in which the blade
cuts completely through the workpiece as in ripping or
cross cutting. Keep the blade guard down, the anti-kick-
back pawls down, and the spreader in place over the
blade.
NEVER OPERATE THE SAW ON THE FLOOR.
GUARD AGAINST KICKBACK. Kickback occurs when
the blade stalls rapidly and workpiece is driven back
towards the operator. It can pull your hand into the blade
resulting in serious personal injury. Stay out of blade path
and turn switch off immediately if blade binds or stalls.
USE RIP FENCE. Always use a fence or straight edge
guide when ripping.
SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
REMOVE ALL FENCES AND AUxILIARY TABLES
before transporting saw. Failure to do so can result in an
accident causing possible serious personal injury.
ALWAYS USE BLADE GUARD, SPREADER, AND ANTI-
KICKBACK PAWLS on all “through-sawing” operations.
ALWAYS SECURE WORK firmly against the rip fence or
miter gauge.
ALWAYS USE A PUSH STICK FOR RIPPING NAR-
ROW STOCK. A push stick is a device used to push a
workpiece through the blade instead of using your hands.
Size and shape can vary but the push stick must always
be narrower than the workpiece to prevent the push stick
from contacting the saw blade. When ripping narrow
stock, always use a push stick, so your hand does not
come close to the saw blade. Use a featherboard and
push blocks for non-through cuts.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
NEVER perform any operation “freehand” which means
using only your hands to support or guide the workpiece.
Always use either the rip fence or miter fence to position
and guide the work.
NEVER stand or have any part of your body in line with
the path of the saw blade.
NEVER reach behind, over, or within three inches of the
blade or cutter with either hand for any reason.
MOVE THE RIP FENCE out of the way when cross cut-
ting.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your hand
to move into the cutting tool.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instruc-
tions for safe use of accessories are included with the
accessory.
MAKE SURE THE WORK AREA HAS AMPLE LIGHTING
to see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
table saw.
ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
NEVER use rip fence as cutoff gauge when cross
cutting.
NEVER attempt to free a stalled saw blade without first
turning the saw OFF and disconnecting the saw from the
power source.
PROVIDE ADEQUATE SUPPORT to the rear and sides
of the saw table for wide or long work pieces.
AVOID KICKBACKS (work thrown back toward you)
by:
ONLY USE BLADES within the thickness range stamped
on the spreader/riving knife.
THIS TOOL should have the following markings:
a) Wear eye protection.
b) Use saw blade guard and spreader/riving knife for
every operation for which it can be used, including
all through sawing.
c) Keep hands out of the line of saw blade.
d) Use a push stick when required.
a) Keeping blade sharp.
b) Keeping rip fence parallel to the saw blade.
c) Keeping spreader, anti-kickback pawls, and
blade guard in place and operating.
d) Not releasing the work before it is pushed all the
way past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or
does not have a straight edge to guide along the
fence.
e) Pay particular attention to instructions on reducing
risk of kickback.
f) Do not perform any operation freehand.
g) Never reach around or over the saw blade.
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions too.
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi-
cals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper inter-
pretation of these symbols will allow you to operate the tool better and safer.
Indicates a potential personal injury hazard.
Safety Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read Operator’s Manual
Always wear eye protection marked to comply with ANSI
Z87.1.
Eye Protection
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Wet Conditions Alert
Pinch Warning
Do not expose to rain or use in damp locations.
Always watch for movement paying extra attention to
potential areas where pinching could occur.
V
A
Volts
Voltage
Current
Amperes
Hz
W
Hertz
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
.../min
Revolutions, strokes, surface speed, orbits etc., per minute
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID® customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
ExTENSION CORDS
SPEED AND WIRING
Use only 3-wire extension cords that have 3-prong ground-
ing plugs and 3-pole receptacles that accept the tool's plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
The no-load speed of this tool is approximately 5,000 rpm.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor’s horsepower rating. A line intended
only for lights cannot properly carry a power tool motor. Wire
that is heavy enough for a short distance will be too light for
a greater distance. A line that can support one power tool
may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
Thisproductmustbegrounded. Intheeventofamalfunction
orbreakdown,groundingprovidesapathofleastresistancefor
electriccurrenttoreducetheriskofelectricshock.Thistoolis
equippedwithanelectriccordhavinganequipment-grounding
conductor and a grounding plug. The plug must be plugged
intoamatchingoutletthatisproperlyinstalledandgrounded
in accordance with all local codes and ordinances.
**Ampere rating (on tool faceplate)
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
100'
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters “W-A” or “W” on the cord’s jacket.
Improper installation of the grounding plug can
result in a risk of electric shock. When repair or
replacement of the cord is required, do not connect
the grounding wire to either flat blade terminal.
The wire with insulation having an outer surface
that is green with or without yellow stripes is the
grounding wire.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 volt circuit and
has a grounding plug similar to the plug illustrated in fig-
ure 1. Only connect the product to an outlet having the same
configuration as the plug. Do not use an adapter with this
product.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use product
with a damaged cord since touching the damaged
area could cause electrical shock resulting in
serious injury.
ELECTRICAL CONNECTION
This product is powered by a precision built electric motor.
It should be connected to a power supply that is 120 V, AC
only (normal household current), 60 Hz. Do not operate
this product on direct current (DC). A substantial voltage
drop will cause a loss of power and the motor will overheat.
If the saw does not operate when plugged into an outlet,
double check the power supply.
120 V
Grounded
outlet
GroundinG
Pin
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Non-Through Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Pilot Hole (drill presses)
Arbor
A small hole drilled in a workpiece that serves as a guide for
The shaft on which a blade or cutting tool is mounted.
drilling large holes accurately.
Bevel Cut
Push Blocks (for jointer planers)
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator's hands well away from the cutterhead.
Chamfer
A cut removing a wedge from a block so the end (or part of
Push Blocks and Push Sticks (for table saws)
the end) is angled rather than at 90°.
Devices used to feed the workpiece through the saw blade
during cutting operations. A push stick (not a push block)
should be used for narrow ripping operations. These aids
help keep the operator's hands well away from the blade.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
Resaw
A cutting or shaping operation made across the grain or the
width of the workpiece.
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Cutter Head (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Dado Cut
A non-through cut which produces a square-sided notch or
trough in the workpiece (requires a special blade).
Ripping or Rip Cut
Featherboard
A cutting operation along the length of the workpiece.
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
Riving Knife/Spreader/Splitter (table saws)
Ametalpiece, slightlythinnerthanthekerf, whichhelpskeep
the kerf open and also helps to prevent kickback.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Gum
A sticky, sap-based residue from wood products.
Snipe (planers)
Heel
Depression made at either end of a workpiece by cutter
Alignment of the blade to the fence.
blades when the workpiece is not properly supported.
Kerf
Through Sawing
The material removed by the blade in a through cut or the
Any cutting operation where the blade extends completely
slot produced by the blade in a non-through or partial cut.
through the thickness of the workpiece.
Kickback
Throw-Back
A hazard that can occur when the blade binds or stalls,
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
throwing the workpiece back toward operator.
Leading End
The end of the workpiece pushed into the tool first.
Workpiece or Material
The item on which the operation is being done.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Worktable
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
No Load Speed ....................................5,000 r/min. (RPM)
Cutting Depth at 0º:...............................................3-1/4 in.
Cutting Depth at 45º:.............................................2-3/8 in.
Blade Arbor ..............................................................5/8 in.
Blade Diameter.......................................................... 10 in.
Blade Tilt .................................................................0˚ - 45˚
Rating ..........................................120 V~, 15 Amps, 60 Hz
BLaDE
guaRD
aNTI-KICKBaCK
RIP
FENCE
PaWLS
SPREaDER/
RIvINg KNIFE
MITER
gaugE
LOCKINg
LEvER
BEvEL
SCaLE
BEvEL
LOCKINg
LEvER
CORD
STORagE
BLaDE
WRENCH
STORagE
HEIgHT/BEvEL
aDJuSTINg
HaNDWHEEL
FRONT
RaIL
SWITCH
aSSEMBLY
Fig. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
MITERGAUGE-Themitergaugealignsthewoodforacross
cut. The easy-to-read indicator shows the exact angle for a
miter cut, with positive stops at 90° and 45°.
KNOW YOUR TABLE SAW
See Figure 2.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
wellasaknowledgeoftheprojectyouareattempting.Before
use of this product, familiarize yourself with all operating
features and safety rules.
MITER GAUGE GROOvES - The miter gauge rides in the
grooves on the saw table.
OUTFEED SUPPORT - This table extension at the back of
the tool gives the operator additional support when cutting
long workpieces.
ANTI-KICKBACK PAWLS - Kickback is a hazard in which
the workpiece is thrown back toward the operator. The teeth
on the removable anti-kickback pawls point away from the
workpiece. If the workpiece should be pulled back toward
the operator, the teeth dig into the wood to help prevent or
reduce the possibility of kickback.
RIPFENCE-Asturdymetalfenceguidestheworkpieceand
is secured with the locking handle. Grooves run along the
top and sides of the rip fence for use with optional clamps
and accessories.
SCALE - Located on the front rail, the easy-to-read scale
provides precise measurements for rip cuts.
BEvEL LOCKING LEvER - This lever, placed just under
the saw table surface on the front of the cabinet, locks the
angle setting of the blade.
SLIDING TABLE EXTENSION - Located on right side
of the saw table, this table extension gives the operator
additional support when cutting wide workpieces.
BEvEL SCALE - The easy-to-read scale on the front of the
cabinet shows the exact blade angle.
SPREADER / RIvING KNIFE - A removable metal piece
of the blade guard assembly, slightly thinner than the saw
blade, whichhelpskeepthekerfopenandpreventkickback.
When in the through sawing, or “up” position, it is higher
than the saw blade and becomes a spreader. When in the
non-through sawing, or “down” position, it is below the saw
blade teeth and becomes a riving knife.
BLADE - This saw is provided with a 36-tooth, 10 in.
carbide blade. The blade is raised and lowered with the
height/bevel adjusting handwheel. Bevel angles are locked
with the bevel locking lever.
WARNING:
SWITCH ASSEMBLY - This saw has an easy access
power switch located below the front rail. To lock the switch
in the OFF position, remove the switch key from the switch.
Place the key in a location that is inaccessible to children
and others not qualified to use the tool.
Do not use blades rated less than the speed of
this tool. Failure to heed this warning could result
in personal injury.
BLADE GUARD - Always keep the removable blade guard
down over the saw blade for through-sawing cuts.
HEIGHT/BEvEL ADJUSTING HANDWHEEL - Located on
thefrontofthecabinet,usethishandwheeltolowerandraise
the blade for height adjustments or blade replacement.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
OPERATING COMPONENTS
WARNING:
The upper portion of the blade projects up through the table
and is surrounded by an insert called the throat plate. The
height of the blade is set with a handwheel on the front of
thecabinet.Toaccommodatewidepanels,thesawtablehas
rails on each side. Detailed instructions are provided in the
Operation section of this manual for the basic cuts: cross
cuts, miter cuts, bevel cuts, and compound cuts.
ALWAYS make sure your workpiece is not in
contact with the blade before operating the
switch to start the tool. Failure to heed this
warning may cause the workpiece to be kicked
back toward the operator and result in serious
personal injury.
The rip fence is used to position work for lengthwise cuts.
A scale on the front rail shows the distance between the rip
fence and the blade.
WARNING:
To reduce the risk of accidental starting, Always
make sure the switch is in the off ( O ) position
before plugging tool into the power source.
It is very important to use the blade guard assembly for
all through-sawing operations. The blade guard assembly
includes: riving knife/spreader/splitter, anti-kickback pawls,
and blade guard.
POWER SWITCH
See Figure 3.
SWITCH
ON
SWITCH
OFF
This saw is equipped with a power switch that has a built-in
locking feature. This feature is intended to prevent unauthor-
ized and possible hazardous use by children and others.
TO TURN YOUR SAW ON:
With the switch key inserted into the switch, lift the switch
button to turn on ( l ).
TO TURN YOUR SAW OFF:
Press the switch button down to turn off ( O ).
TO LOCK YOUR SAW:
Press the switch button down.
SWITCH KEY REMOvED
Remove the switch key from the switch and store in a
safe, secure location.
WARNING:
Always remove the switch key when the tool is
not in use and keep it in a safe place. In the event
of a power failure, turn the switch off ( O ) and
remove the key. This action will prevent the tool
from accidentally starting when power returns.
Fig. 3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly and alignment:
FRaMINg SquaRE
PHILLIPS
SCREWDRIvER
COMBINaTION
SquaRE
FLaT BLaDE
SCREWDRIvER
Fig. 4
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
The following items are included with your table saw:
B
a
C
D
E
F
g
I
H
Fig. 5
E. Handle Assembly .................................................... 1
F. Push Stick ............................................................... 1
G. Blade Wrench, large................................................ 1
H. Blade Wrench, small................................................ 1
I. Hex Key, 5 mm........................................................ 1
A. Blade Guard ............................................................ 1
B. Anti-Kickback Pawls ............................................... 1
C. Miter Gauge............................................................. 1
D. Rip Fence ................................................................ 1
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product requires assembly.
WARNING:
To avoid serious personal injury, always make sure
the table saw is securely mounted to a workbench
or an approved leg stand. NEVER operate the saw
on the floor.
Carefully lift the saw from the carton and place it on a level
work surface.
WARNING:
Do not use this product if any parts on the Loose
Parts List are already assembled to your product
when you unpack it. Parts on this list are not as-
sembled to the product by the manufacturer and
require customer installation. Use of a product that
may have been improperly assembled could result
in serious personal injury.
MOUNTING HOLES
The table saw must be mounted to a firm supporting, waist
high surface such as a workbench or leg stand. Four bolt
holes have been provided in the saw’s base for this purpose.
Each of the four mounting holes should be bolted securely
using 1/4 in. machine bolts, lock washers, and hex nuts (not
included).Boltsshouldbeofsufficientlengthtoaccommodate
the saw base, lock washers, hex nuts, and the thickness of
the workbench. Tighten all four bolts securely.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Carefully check the workbench after mounting to make sure
that no movement can occur during use. If any tipping, slid-
ing, or walking is noted, secure the workbench to the floor
before operating.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has influ-
enced the settings, refer to specific procedures explained
in this manual.
TO INSTALL THE HANDLE ASSEMBLY
See Figure 6.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
Lift the end cap off the handle assembly using a flat blade
screwdriver.
Hold the nylok nut securely and turn the screw counter-
WARNING:
clockwise to remove the nut completely.
NOTE: Do not remove the screw from the handle or the
washer from the end of the screw.
If any parts are damaged or missing do not oper-
ate this tool until the parts are replaced. Use of
this product with damaged or missing parts could
result in serious personal injury.
Place the nylok nut into the recessed hole on the back of
the height/bevel adjusting handwheel and hold in place.
Slide the handle, screw, and washer into the hole on the
height/bevel adjusting handwheel.
WARNING:
Using a flathead screwdriver, turn the screw clockwise and
tighten in place.
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
Push the end cap back in place on the end of the handle.
NuT
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in acci-
dental starting and possible serious personal injury.
HaNDLE
aSSEMBLY
END
CaP
WARNING:
Never stand directly in line with the blade or allow
hands to come closer than 3 in. to the blade. Do
not reach over or across the blade. Failure to heed
this warning can result in serious personal injury.
HEIgHT/BEvEL
aDJuSTINg
HaNDWHEEL
Fig. 6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO STORE THE TABLE SAW ACCESSORIES
See Figures 7 - 8.
The table saw has two convenient storage areas (one on
either side of the saw cabinet) specifically designed for the
saw’s accessories.
When not in use, store accessories securely.
RAISING AND LOWERING THE HANDLE
See Figure 9.
To raise the handle, pull the handle up.
NOTE: The handle will “click” as it locks in place.
Tolowerthehandle,pushthehandledownintothehandle
tube.
TO MOvE THE SAW
See Figure 10.
MITER
gaugE
PuSH STICK
Fig. 8
Holding the handle firmly, tilt the saw toward you until the
saw is balanced on the wheels.
HaNDLE
Pull the saw to the desired location then either mount
to a firm supporting surface such as a workbench or leg
stand for immediate saw operation or store the saw in a
dry environment.
Fig. 9
BLaDE
WRENCHES
Fig. 7
Fig. 10
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
THROaT
PLaTE
TO REMOvE/REPLACE THE THROAT PLATE
See Figure 11.
Lower the blade by turning the height/bevel adjusting
SPREaDER /
RIvINg KNIFE
handwheel clockwise.
To remove the throat plate, place your index finger in
the hole and lift the front end pulling the throat plate out
toward the front of the saw.
To reinstall the throat plate, slip the tab into the slot at
the back of the saw and push down to secure in place.
TO CHANGE BETWEEN A SPREADER AND A
RIvING KNIFE
See Figure 12.
This saw is shipped with the spreader/riving knife placed
in the non-through cutting or “down” position (riving knife
position).
NOTE: The spreader/riving knife must be placed in the
through cutting, or “up” position (spreader position), for all
other cutting operations.
Fig. 11
RELEaSE
Unplug the saw.
LEvER
To place in spreader position (or “up” position for all
through cutting):
(uNLOCKED)
Remove the throat plate.
Raise the saw blade by turning the height/bevel adjusting
handwheel counterclockwise.
Unlock the release lever by pulling it up.
Grasp the spreader and pull up until the internal pins are
engaged and the spreader is above the saw blade.
Lock the release lever by pushing the lever down.
Reinstall the throat plate.
To place in riving knife position (or “down” position for
all non-through cutting):
Remove the throat plate.
IN “uP” POSITION FOR THROugH CuTTINg
Raise the saw blade by turning the height/bevel adjusting
handwheel counterclockwise.
RELEaSE
Unlock the release lever by pulling it up.
LEvER
(LOCKED)
Push the riving knife down until it is below the saw
blade.
Lock the release lever by pushing the lever down.
Reinstall the throat plate.
IN “DOWN” POSITION FOR NON-THROugH CuTTINg
Fig. 12
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
LaRgE
BLaDE WRENCH
TO CHECK SAW BLADE INSTALLATION
See Figure 13.
SMaLL BLaDE
WRENCH
CAUTION:
To work properly, the saw blade teeth must point
down toward the front of the saw. Failure to do
so could cause damage to the saw blade, the
saw, or the workpiece.
Unplug the saw.
Lowerthesawbladebyturningtheheight/beveladjusting
handwheel clockwise and remove the throat plate.
Make sure the bevel locking lever is securely pushed to
theleft. Raisethesawbladetoitsfullheightbyturningthe
height/bevel adjusting handwheel counterclockwise.
Place spreader/riving knife in “up” position.
To loosen the blade:
Using the smaller blade wrench, place the flat open end
on the flats on the arbor shaft.
Insert the closed end of the larger blade wrench over
the hex nut. Holding both wrenches firmly, pull the larger
wrench forward to the front of the machine.
Fig. 13
BuTTON
To tighten the blade:
Using the smaller blade wrench, place the flat open end
PaWL
HaNDLE
into the flats on the arbor shaft.
Insert the closed end of the larger blade wrench over the
hex nut. Holding both wrenches firmly, push the larger
wrench to the back of the machine. Make sure the blade
nut is securely tightened. Do not overtighten.
Reinstall the throat plate.
Check all clearances for free blade rotation.
aNTI-KICKBaCK
PaWLS
TO INSTALL THE ANTI-KICKBACK PAWLS AND
BLADE GUARD
See Figures 14 - 15.
NOTE: Anti-kickback pawls should only be installed for
through cuts.
Unplug the saw.
Raise the saw blade.
Place spreader/riving knife in “up” position.
To install anti-kickback pawls:
Press and hold the button on the right side of the anti-
kickback pawls.
Aligntheslotinthepawlsovertherearholeinthespreader/
riving knife.
Fig. 14
Push the pawl handle down snapping them into place
and release the button.
NOTE: Pull on the handle to make sure pawls are
securely locked.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
guaRD
LEvER
To install blade guard:
BLaDE
guaRD
With the front of the blade guard raised and the guard
lever unlocked, lower the back of the guard into the
middle hole of the spreader/riving knife. Push the front
of the guard down until it is parallel to the table.
Lock the guard in place by pushing the lever down.
NOTE: Blade alignment with the spreader can be adjusted
for different blade widths. Refer to: To Check and Align the
Spreader/RivingKnifeandSawBlade.Checkthebladeguard
assembly for clearances and free movement.
TO CHECK AND ALIGN THE SPREADER/
RIvING KNIFE AND SAW BLADE
See Figure 16.
If the spreader/riving knife is out of alignment with the saw
blade, adjustment is needed.
Fig. 15
SCREW
To check alignment of the spreader/riving knife:
Unplug the saw.
Raise the saw blade by turning the height/bevel adjusting
handwheel counterclockwise.
Remove the anti-kickback pawls and blade guard
assembly.Placeaframingsquareorstraightedgeagainst
both the saw blade and the spreader.
NOTE: Place framing square between carbide teeth and
measure from blade. This step will insure framing square
is square against blade from the front to back of blade.
Thesawbladeandspreader/rivingknifearealignedwhen
theframingsquarecontactsboththebladeandspreader/
riving knife evenly with no gaps.
To adjust:
Remove the anti-kickback pawls and blade guard
assembly.
SCREW
SPREaDER/
RIvINg KNIFE
Loosen the screws holding the mounting bracket.
Repositionthespreader/rivingknifeleftorrightasneeded
FRaMINg
SquaRE
to align the spreader/riving knife with the saw blade.
Once properly aligned, securely retighten the screws.
Fig. 16
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CAUSES Of KICKBACK
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
Kickback can occur when the blade stalls or binds, kicking
theworkpiecebacktowardyouwithgreatforceandspeed.If
your hands are near the saw blade, they may be jerked loose
fromtheworkpieceandmaycontacttheblade.Kickbackcan
cause serious injury. Use precautions to avoid the risks.
Kickback can be caused by any action that pinches the
blade in the wood such as:
WARNING:
Making a cut with incorrect blade depth
Sawing into knots or nails in the workpiece
Twisting the wood while making a cut
Failing to support work
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes, resulting in possible serious injury.
Forcing a cut
Cutting warped or wet lumber
Using the wrong blade for the type of cut
Not following correct operating procedures
Misusing the saw
Failing to use the anti-kickback pawls
Cutting with a dull, gummed-up, or improperly set
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool.
The use of attachments or accessories not rec-
ommended can result in serious personal injury.
blade
AVOIDING KICKBACK
Always use the correct blade depth setting. The top of
the blade teeth should clear the workpiece by 1/8 in. to
1/4 in.
WARNING:
Although many of the illustrations in this manual
are shown with the blade guard removed for clarity,
do not operate the saw without the blade guard
unless specifically instructed to do so.
Inspect the work for knots or nails before beginning a
cut. Knock out any loose knots with a hammer. Never
saw into a loose knot or nail.
Always use the rip fence when rip cutting and the miter
gauge when cross cutting. This helps prevent twisting
the wood in the cut.
WARNING:
The table saw must be mounted to a firm support-
ing, waist high surface such as a workbench or leg
stand. Many illustrations in this manual are shown
with the saw unmounted for clarity.
Always use clean, sharp, and properly-set blades. Never
make cuts with dull blades.
To avoid pinching the blade, support the work properly
before beginning a cut.
When making a cut, use steady, even pressure. Never
APPLICATIONS
force cuts.
You may use this tool for the purposes listed below:
Do not cut wet or warped lumber.
Straight line cutting operations such as cross cutting,
ripping, mitering, beveling, and compound cutting
Dado or molding cuts with optional accessories
Alwaysholdyourworkpiecefirmlywithbothhandsorwith
push sticks. Keep your body in a balanced position to
be ready to resist kickback should it occur. Never stand
directly in line with the blade.
Cabinet making and woodworking
Use the right type of blade for the cut being made.
NOTE: This table saw is designed to cut wood and wood
composition products only.
CUTTING AIDS
See Figure 17.
BASIC OPERATION Of ThE TABLE SAW
Push sticks are devices used for safely pushing a workpiece
through the blade. They can be made in various sizes and
shapes from scrap wood to use in a specific project. The
stick must be narrower than the workpiece, with a 90˚ notch
in one end and shaping for a grip on the other end.
The 3-prong plug must be plugged into a matching outlet
that is properly installed and grounded according to all local
codes and ordinances. Improper connection of the equip-
ment can result in electric shock. Do not modify the plug if
it will not fit the outlet. Have the correct outlet installed by
a qualified electrician. Refer to the Electrical section in this
manual.
A push block has a handle fastened by recessed screws
from the underside. Be sure the screw is recessed. Use it
on non-through cuts.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Prepare the saw for ripping as discussed on page 27. Set the
rip fence to allow approximately a 1/4 in. “finger” to be cut in
the stock. Feed the stock only to the mark previously made
at 6 in. Turn the saw Off and allow the blade to completely
stop rotating before removing the stock. Reset the rip fence
andcutspacedripsintotheworkpiecetoallowapproximately
1/4 in. fingers and 1/8 in. spaces between the fingers.
push sticks
hOW TO MOUNT A fEAThERBOARD
See Figure 19.
Completely lower the saw blade. Position the rip fence to the
desired adjustment for the cut to be performed and lock the
ripfence. Placetheworkpieceagainstthefenceandoverthe
saw blade area. Adjust the featherboard to apply resistance
to the workpiece just forward of the blade. Attach C-clamps
to secure the featherboard to the edge of the saw table.
push blocks
Fig. 17
fEAThERBOARD
Afeatherboardisadeviceusedtohelpcontroltheworkpiece
by guiding it securely against the table or fence. Feather-
boards are especially useful when ripping small workpieces
and for completing non-through cuts. The end is angled
with a number of short kerfs to give a friction hold on the
workpiece and locked in place on the table with a C-clamp.
Test that it can resist kickback.
WARNING:
The featherboard must be installed in front of
the blade. Do not locate the featherboard to the
rear of the blade. Kickback can result from the
featherboard pinching the workpiece and binding
the blade in the saw kerf if positioned improperly.
Failure to heed this warning can result in serious
personal injury.
WARNING:
Place the featherboard against the uncut portion of
the workpiece to avoid kickback that could cause
serious personal injury.
push block
hOW TO MAKE A fEAThERBOARD
See Figure 18.
The featherboard is an excellent project for your saw.
Select a solid piece of lumber approximately 3/4 in. thick,
3-5/8 in. wide and 18 in. long. Mark the center of the width
on one end of the stock. Miter one-half of the width to 30°
and miter the other half of the same end to 45° (see page
28 for information on miter cuts). Mark the board from the
point at 6 in., 8 in., 10 in. and 12 in. Drill a 3/8 in. hole at the
8 in., 10 in., and 12 in. marks.
push
stick
featherboard
Fig. 19
30°
3-5/8 in.
3/4 in.
1/4 in.
1-13/16 in.
45°
1/8 in.
6 in.
18 in.
Fig. 18
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TyPES Of CUTS
See Figure 20.
There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the
miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and
6) the compound (bevel) miter cut. All other cuts are
combinations of these basic six. Operating procedures for
making each kind of cut are given later in this section.
1
cross cut
WARNING:
2
3
4
Always make sure the blade guard and anti-kick-
back pawls are in place and working properly when
making these cuts to avoid possible injury.
rip cut
Cross cuts are straight 90° cuts made across the grain of
the workpiece. The wood is fed into the cut at a 90° angle
to the blade, and the blade is vertical.
Rip cuts are made with the grain of the wood. To avoid
kickback while making a rip cut, make sure one side of the
wood rides firmly against the rip fence.
Miter cut
Miter cuts are made with the wood at any angle to the
blade other than 90°. The blade is vertical. Miter cuts tend
to “creep” during cutting. This can be controlled by holding
the workpiece securely against the miter gauge.
WARNING:
bevel cross cut
Always use a push stick with small pieces of wood,
and also to finish the cut when ripping a long nar-
row piece of wood, to prevent your hands from
getting close to the blade.
5
6
Bevel cuts are made with an angled blade. Bevel cross cuts
are across the wood grain, and bevel rip cuts are with the
grain. The rip fence must always be on the right side of the
blade for bevel rip cuts.
bevel rip cut
Compound (or bevel) miter cuts are made with an angled
blade on wood that is angled to the blade. Be thoroughly
familiar with making cross cuts, rip cuts, bevel cuts, and
miter cuts before trying a compound miter cut.
coMpound (bevel) Miter cut
CUTTING TIPS
Fig. 20
Dado and rabbet cuts are non-through cuts which can be
either rip cuts or cross cuts. Carefully read and understand
all sections of this operator’s manual before attempting any
operation.
The kerf (the cut made by the blade in the wood) will be
wider than the blade to avoid overheating or binding.
Make allowance for the kerf when measuring wood.
Make sure the kerf is made on the waste side of the
WARNING:
measuring line.
Do not use blades rated less than the speed of
this tool. Failure to heed this warning could result
in personal injury.
Cut the wood with the finish side up.
Knock out any loose knots with a hammer before making
the cut.
Always provide proper support for the wood as it comes
out of the saw.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
to unlock
to lock
TO ChANGE BLADE DEPTh
See Figure 21.
The blade depth should be set so the outer points of the
blade are higher than the workpiece by approximately 1/8
in. to 1/4 in. but the lowest points (gullets) are below the
top surface.
Raise the blade by turning the height/bevel adjusting
handwheel counterclockwise.
Lower the blade by turning the handwheel clockwise.
TO ChANGE BLADE ANGLE
bevel locking
See Figure 22.
lever
NOTE: A 90° cut has a 0° bevel and a 45° cut has a 45°
bevel.
Unplug the saw.
Unlock the bevel locking lever by pushing the lever to the
right.
to decrease
Adjust the bevel angle by pushing the wheel in toward the
saw then turning it. Turning the wheel counterclockwise
increases the angle of the blade, bringing it closer to 45°.
Turning it clockwise decreases the angle, bringing the
blade closer to 90°.
angle
Lock the bevel locking lever by pushing the lever to the
left.
to increase
TO ADjUST ThE BEVEL INDICATOR
See Figure 23.
angle
Fig. 22
If the bevel indicator is not at zero when the saw blade is at
0°, adjust the indicator by loosening the screw and setting
it at 0° on the bevel scale. Retighten the screw.
bevel
locking lever
gullet
Fig. 21
screW
height/bevel
adjusting
handWheel
bevel
indicator
Fig. 23
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
rip
fence
blade
WARNING:
scale
To reduce the risk of injury, always make sure the
rip fence is parallel to the blade before beginning
any operation.
2 in.
TO SET ThE RIP fENCE SCALE INDICATOR
TO ThE BLADE
See Figure 24.
Use the indicator on the rip fence to position the fence along
the scale on the front rail.
NOTE: The anti-kickback pawls and blade guard assembly
must be removed to perform this adjustment. Reinstall the
blade guard assembly when the adjustment is complete.
Begin with the blade at a zero angle (straight up).
Unplug the saw.
front
rail
Loosen the rip fence by lifting the locking lever.
screW
Using a framing square, set the rip fence 2 in. from the
locking
lever
2 in.
Mark
blade tip edge.
Loosen the screw on the scale indicator.
Fig. 24
Tighten the screw and check the dimension and the rip
locking
lever
fence.
rip
fence
TO USE ThE RIP fENCE
See Figure 25.
saW
table
Place the rear lip on the rear of the saw table and pull
slightly toward the front of the unit.
Lower the front end of the rip fence onto the guide
surfaces on top of the front rail.
Push the locking lever down to automatically align and
secure the fence.
Checkforasmoothglidingaction.Ifadjustmentsareneeded,
see To Check the Alignment of the Ripfence to the Blade
in the Adjustment section of this manual.
rear
lip
Fig. 25
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
lock
knob
TO USE ThE MITER GAUGE
See Figure 26.
The miter gauge provides greater accuracy in angled cuts.
For very close tolerances, test cuts are recommended.
There are two miter gauge channels, one on either side of
the blade. When making a 90° cross cut, you can use either
miter gauge channel. When making a beveled cross cut (the
blade tilted in relation to the table) the miter gauge should
be located in the slot on the right so that the blade is tilted
away from the miter gauge and your hands.
Miter
gauge
Fig. 26
The miter gauge can be turned 60° to the right or left.
Loosen the lock knob.
fence
With the miter gauge in the miter gauge slot, rotate the
sliding table
extension
gauge until the desired angle is reached on the scale.
Retighten the lock knob.
TO USE ThE SLIDING TABLE ExTENSION
See Figure 27.
Increase the length of the saw table by using the table
extension.
table
Set the rip fence to 13 in.
locking
lever
Pull the front table locking lever toward you to unlock the
lever.
Slide the table extension to the desired width.
NOTE: Use the scale on the front rail when a specific
width is desired.
Once the extension table is set to the desired width,
relock the lever by pushing the lever back towards the
saw base.
scale
Fig. 27
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
(1)
hEELING (PARALLELING) ThE BLADE TO ThE
MITER GAUGE GROOVE
See Figures 28 - 30.
(2)
(3)
adjusting
bolts (3)
WARNING:
The blade must be square so the wood does not
bind resulting in kickback. Failure to do so could
result in serious personal injury.
Do not loosen any bolts for this adjustment until you have
checked with a square and made test cuts to be sure adjust-
ments are necessary. Once the bolts are loosened, these
items must be reset.
Fig. 28
Miter
gauge
groove
Unplug the saw.
coMbination
sQuare
Remove the blade guard and anti-kickback pawls.
Raise the blade by turning the height/bevel adjusting
handwheel.
Markbesideoneofthebladeteethatthefrontoftheblade.
Placeacombinationsquareevenwiththefrontofthesaw
table and the side of the saw blade as shown in figure 28.
Turn the blade so the marked tooth is at the back.
Move the combination square to the rear and again
measure the distance. If the distances are the same, the
blade is square.
If the distances are different:
Place spreader/riving knife in "down" position then lower
the blade.
Loosen adjusting bolts (1) and (3).
NOTE: The adjusting bolts are located under the saw
table in the back of the saw.
Fig. 29
Turn adjusting bolt (2) left or right until the blade is
square.
coMbination
sQuare
WARNING:
To reduce the risk of injury from kickback, align the
rip fence to the blade following any blade adjust-
ments. Always make sure the rip fence is parallel
to the blade before beginning any operation.
Fig. 30
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
cross cut
MAKING CUTS
The blade provided with your saw is a high-quality combi-
nation blade suitable for ripping and cross cut operations.
Carefully check all setups and rotate the blade one full
revolution to assure proper clearance before connecting
saw to power source. Stand slightly to the side of the blade
path to reduce the chance of injury should kickback occur.
place left hand on
Workpiece and
Miter gauge here
WARNING:
Do not use blades rated less than the speed of
this tool. Failure to heed this warning could result
in personal injury.
Use the miter gauge when making cross, miter, bevel, and
compound miter cuts. To secure the angle, lock the miter
gauge in place by twisting the lock knob clockwise. Always
tighten the lock knob securely in place before use.
NOTE: It is recommended that you place the piece to be
saved on the left side of the blade and that you make a test
cut on scrap wood first.
Fig. 31
TO MAKE A CROSS CUT
See Figures 31 - 32.
sWitch
off
sWitch
on
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid serious possible
injury.
WARNING:
Using the rip fence as a cutoff gauge when cross
cutting will result in kickback which can cause
serious personal injury.
sWitch
keY
Remove the rip fence.
Set the blade to the correct depth for the workpiece.
Set the miter gauge to 0° and tighten the lock knob.
Make sure the wood is clear of the blade before turning
on the saw.
sWitch in locked position
To turn the saw on, lift the switch button.
Fig. 32
To turn saw off, press the switch button down.
NOTE: To prevent unauthorized use, remove the switch
key as shown in figure 32.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
Let the blade build up to full speed before moving the
workpiece into the blade.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
rip cut
MAKING A RIP CUT
See Figure 33.
blade
rip
fence
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid serious possible
injury.
Set the blade to the correct depth for the workpiece.
Position the rip fence the desired distance from the blade
for the cut and securely lock the handle.
Make sure the wood is clear of the blade before turning
on the saw.
scale
Whenrippingalongworkpiece, placeasupportthesame
height as the table surface behind the saw for the cut
work.
Fig. 33
Turn the saw on.
Miter cut
blade
Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
straight
Miter gauge
Oncethebladehasmadecontactwiththeworkpiece,use
the hand closest to the rip fence to guide it. Make sure
the edge of the workpiece remains in solid contact with
both the rip fence and the surface of the table. If ripping
a narrow piece, use a push stick and/or push blocks to
move the piece through the cut and past the blade.
angled
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MAKING A MITER CUT
See Figure 34.
WARNING:
height/bevel
adjusting
Make sure the blade guard assembly is installed
and working properly to avoid possible serious
injury.
handWheel
Fig. 34
Remove the rip fence.
Hold the workpiece firmly with both hands on the miter
Set the blade to the correct depth for the workpiece.
gauge and feed the workpiece into the blade.
Set the miter gauge to the desired angle and tighten the
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
lock knob.
Make sure the wood is clear of the blade before turning
on the saw.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Turn the saw on.
Let the blade build up to full speed before moving the
workpiece into the blade.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
vieWed froM the front, beloW the table saW
MAKING A BEVEL CROSS CUT
See Figures 35 - 36.
to lock
to unlock
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid possible serious
injury.
Remove the rip fence.
Unlock the bevel locking lever.
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
bevel lock
lever
Set the blade to the correct depth for the workpiece.
Set the miter gauge to 0° and tighten the lock knob.
height/bevel
adjusting
handWheel
Make sure the wood is clear of the blade before turning
on the saw.
Fig. 35
Turn the saw on.
Let the blade build up to full speed before moving the
bevel cross cut
workpiece into the blade.
Hold the workpiece firmly with both hands on the miter
blade
angled
gauge and feed the workpiece into the blade.
Miter gauge
straight
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MAKING A BEVEL RIP CUT
See Figure 37.
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid serious personal
injury.
bevel
locking
lever
WARNING:
Fig. 36
The rip fence must be on the right side of the blade
to avoid trapping the wood and causing kickback.
Placement of the rip fence to the left of the blade
will result in kickback and the risk of serious per-
sonal injury.
Position the rip fence the desired distance from the blade
for the cut and securely lock the handle.
Make sure the wood is clear of the blade before turning
on the saw.
Whenrippingalongworkpiece, placeasupportthesame
height as the table surface behind the saw for the cut
work.
Unlock the bevel locking lever.
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
Turn the saw on.
Set the blade to the correct depth for the workpiece.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
bevel rip cut
rip fence
Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
blade
angled
Oncethebladehasmadecontactwiththeworkpiece,use
the hand closest to the rip fence to guide it. Make sure
the edge of the workpiece remains in solid contact with
both the rip fence and the surface of the table. If ripping
a narrow piece, use a push stick and/or push blocks to
move the piece through the cut and past the blade.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
push
stick
MAKING A COMPOUND (BEVEL) MITER CUT
See Figure 38.
Fig. 37
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid possible serious
injury.
coMpound (bevel) Miter cut
place left hand on
Miter gauge here
Remove the rip fence.
Unlock the bevel locking lever.
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
Set the blade to the correct depth for the workpiece.
Set the miter gauge to the desired angle and tighten
the lock knob.
Make sure the wood is clear of the blade before turning
on the saw.
Turn the saw on.
Let the blade build up to full speed before moving the
workpiece into the blade.
Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
Fig. 38
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
WARNING:
Never make freehand cuts (cuts without the miter
gauge or rip fence), which can result in serious
injury.
MAKING A LARGE PANEL CUT
See Figure 39.
Make sure the saw is properly secured to a work surface
to avoid tipping from the weight of a large panel.
Place a support the same height as the top of the saw
table behind the saw for the cut work. Add supports to
the sides as needed.
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid possible serious
injury.
Depending on the shape of the panel, use the rip fence
or miter gauge. If the panel is too large to use either the
rip fence or the miter gauge, it is too large for this saw.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
large panel cut
rip fence
Make sure the wood does not touch the blade before you
turn on the saw.
Turn the saw on.
Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
Use a push stick to move the piece through the cut and
past the blade.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MAKING A NON-ThROUGh CUT
See Figure 40.
Non-through cuts (made with a standard 10 in. blade) can be
made with the grain (ripping) or across the grain (cross cut).
The use of a non-through cut is essential to cutting grooves,
rabbets, and dadoes. This is the only type cut that is made
without the blade guard assembly installed. Make sure the
blade guard assembly is reinstalled upon completion of this
type of cut. Read the appropriate section which describes
the type of cut in addition to this section on non-through or
dado cuts. For example, if your non-through cut is a straight
cross cut, read and understand the section on straight cross
cuts before proceeding.
height/bevel
adjusting
handWheel
supports
Fig. 39
WARNING:
Depending on the shape and size of the wood, use either
the rip fence or miter gauge.
When making a non-through cut, the cutter is cov-
ered by the workpiece during most of the cut. Be
alert to the exposed cutter at the start and finish of
every cut to avoid the risk of personal injury.
Plug the saw into the power source and turn the saw
on.
Let the blade build up to full speed before moving the
workpiece into the blade.
Always use push blocks, push sticks, and featherboards
when making non-through cuts to avoid the risk of serious
injury.
WARNING:
Never feed wood with your hands when making
any non-through cut such as rabbets or dadoes.
To avoid personal injury, always use push blocks,
push sticks, and featherboards.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Once all non-through cuts are completed:
Unplug your saw.
Unplug the saw.
Reinstall the spreader/riving knife in the “up” position
Remove the blade guard and anti-kickback pawls.
Place spreader / riving knife in “down” position.
Unlock the bevel locking lever.
then install the blade guard and anti-kickback pawls.
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
Set the blade to the correct depth for the workpiece.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
non-through cut
MAKING A DADO CUT
See Figure 41.
blade
guard
reMoved
An optional dado throat plate is required for this procedure
(see the Accessories section of this manual and check with
the retailer where the table saw was purchased). All blades
and dado sets must not be rated less than the speed of this
tool. This saw is designed for use with a 6 in. stack dado
(up to width of 3/4 in.). Do not use an adjustable dado on
this saw.
WARNING:
Always put all spacers in proper location when
changing back to saw blade. Failure to do so may
result in possible injury and damage to the tool.
push
stick
WARNING:
Fig. 40
Always use push blocks, push sticks, or feather-
boards when making dado cuts to avoid the risk
of serious injury.
dado cut
WARNING:
Always store the blade washer and throat plate in
secure location when changing back to saw blade.
Failure to do so may result in possible injury and
damage to the tool.
Unplug your saw.
Remove the blade guard, anti-kickback pawls, throat
plate, and spreader/riving knife.
Remove the blade nut, outer blade washer, saw blade,
inner blade washer, and spacer (see figure 43).
Fig. 41
Reinstall the inner blade washer.
Position the workpiece flat on the table with the edge
Mountthedadoblade,accordingtomanufacturerinstruc-
tions, using the blade and chippers appropriate for the
desired width of cut.
flush against the rip fence or miter gauge.
Use a push block or push stick to move the wood through
the cut past the blade. Never push a small piece of wood
into the blade with your hand, always use a push stick.
The use of push blocks, push sticks, and featherboards
are necessary when making non-through cuts.
Reinstall the blade nut.
NOTE:Thebladewashermaybeusedprovidedthearbor
shaft extends slightly beyond the arbor nut.
Make sure the blade nut is fully engaged and the arbor
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
extends past a securely tightened blade nut.
Place release lever in locked position.
Install the dado throat plate and rotate the blade by hand
Once all dado cuts are completed:
Unplug your saw.
to make sure it turns freely then lower the blade.
Depending on the shape and size of the wood, use either
Reinstall the spreader/riving knife in the “up” position
the rip fence or miter gauge.
then install the blade guard and anti-kickback pawls.
Turn the saw on.
NOTE: Make sure the wood does not touch the blade
before you turn on the saw. Let the blade build up to full
speed before feeding the workpiece into the blade.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
adjustments
LARGE
bLAdE WRENCH
WaRnInG:
SMALL bLAdE
WRENCH
Before performing any adjustment, make sure
the tool is unplugged from the power supply
and the switch is in the OFF ( O ) position. Fail-
ure to heed this warning could result in serious
personal injury.
To avoid unnecessary set-ups and adjustments, a good
practice is to check your setups carefully with a framing
square and make practice cuts in scrap wood before making
finish cuts in good workpieces. Do not start any adjustments
until you have checked with a square and made test cuts to
be sure adjustments are needed.
Fig. 42
OutER bLAdE
WASHER
tO Replace the blade
bLAdE
See Figures 42 - 44.
INNER bLAdE
WASHER
nOte: Arbor shaft has right-hand threads.
Unplug the saw.
Lower the saw blade and remove the throat plate.
bLAdE
Nut
Raise the saw blade to full height then remove the blade
SpACER
guard and anti-kickback pawls.
Make sure the bevel locking lever is locked.
Insert the open end of the small blade wrench onto the
flats on the arbor shaft.
RELEASE
LEVER
Insert the closed end of the large wrench over the hex
nut.Holdingbothwrenchesfirmly,pulltheoutsidewrench
(right side) forward while pushing the inside (left side) to
the back of the saw.
Unlock the release locking lever and remove the blade.
ARbOR
SHAFt
to install a standard blade:
Fig. 43
Place the new blade on the arbor shaft (blade teeth
must point down toward the front of the saw to work
properly).
tHROAt
pLAtE
SpREAdER/
RIVING KNIFE
Place the blade washer and the blade nut over the arbor
shaft. Be sure the dome side of the blade washer faces
out from the blade and that all items are snug against
the arbor housing. Make sure the blade nut is securely
tightened. Do not overtighten.
bLAdE
Lock the release lever.
Rotate the blade by hand to make sure it turns freely.
Lower the saw blade and reinstall the throat plate.
nOte: To replace the blade with an accessory blade, fol-
low the instructions provided with the accessory.
Fig. 44
33
Download from Www.Somanuals.com. All Manuals Search And Download.
adjustments
0° AdJuStMENt
bOLt
tO set the blade at 0° and 45°
See Figures 45 - 46.
bLAdE
COMbINAtION
SQuARE
The angle settings of your saw have been set at the factory
and, unless damaged in shipping, should not require set-
ting during assembly. After extensive use, it may need to be
checked.
bEVEL
LOCKING
LEVER
Raise the blade and remove the blade guard.
If the blade is not perfectly vertical (0°):
Loosen the adjustment bolt and the bevel locking lever.
Place a combination square beside the blade on the left.
Lock the angle by pushing the bevel locking lever and
retighten the adjustment bolt.
Turn the bevel handle until the bevel indicator points to
zero. If the bevel handle is turned as far as possible and
doesn't indicate zero properly, you may need to adjust
the bevel indicator.
If the blade is not an exact 45°:
Loosen the adjustment bolt and the bevel locking lever.
bEVEL
INdICAtOR
bEVEL
HANdLE
Place a combination square beside the blade on the left.
Lock the angle by pushing the bevel locking lever and
retighten the adjustment bolt.
Fig. 45
Turn the bevel handle until the bottom of the blade has
moved completely to the left side of the slot. Lock the
angle by pushing the bevel locking lever.
45° AdJuStMENt
bOLt
bLAdE
If the blade is not an exact 45°, loosen the adjustment
COMbINAtION
bolt and the bevel locking lever.
SQuARE
45°
Adjust the bevel indicator to 45°.
bEVEL
INdICAtOR
bEVEL LOCKING
LEVER
bEVEL
HANdLE
Fig. 46
34
Download from Www.Somanuals.com. All Manuals Search And Download.
adjustments
MItER
GAuGE bASE
KNOb
tO adjust the mIteR GauGe
See Figure 47.
You can set the miter gauge at 0° and plus or minus 45° with
the miter gauge stop pin and adjustable stop screws.
StOp
pIN
nOte: The miter gauge provides close accuracy in
angled cuts. For very close tolerances, test cuts are
recommended.
MItER
GAuGE ROd
Loosen knob and pull out on stop pin to rotate miter
gauge base past stop screws.
Loosen the lock nut of the 0° stop screw at the stop pin
with a 8 mm wrench.
45° AdJuStAbLE
StOp SCREW
0° AdJuStAbLE
StOp SCREW
Place a 90° square against the miter gauge rod and the
miter gauge base.
LOCK
Nut
If the rod is not square, loosen the knob, adjust the rod,
Fig. 47
and tighten the knob.
Adjust the 0° stop screw until it rests against the stop
pin.
FRAMING
SQuARE
Adjust the plus and minus 45° stop screws using a 45°
RIp FENCE
triangle and the steps above.
bLAdE
tO checK the alIGnment OF the RIp
Fence tO the blade
See Figure 48.
WaRnInG:
To reduce the risk of injury, always make sure the
rip fence is parallel to the blade before beginning
any operation.
Unplug the saw.
Raise the locking lever to permit the rip fence to be
moved.
Place a framing square beside the blade and move the
rip fence up to the square. Take the dimension on the rip
scale.
SCREWS
LOCKING
LEVER
Move the fence back and turn the framing square 180°
to check the other side.
If the two dimensions are not the same, loosen the two
Fig. 48
screws on the fence and align it.
Retighten the two screws.
Make two or three test cuts on scrap wood. If the cuts
are not true, repeat the process.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Check the blade guard assembly.
wARNINg:
When servicing, use only identical RIDGID re-
placement parts. Use of any other parts may
create a hazard or cause product damage.
To maintain the table surfaces, fence, and rails,
periodically apply paste wax to them and buff to provide
smooth functioning. To prevent work from slipping during
cutting operation, Do not wax the working face of the
miter gauge.
Protect the blade by cleaning out saw dust from
underneath the table and in the blade teeth. Use a resin
solvent on the blade teeth.
wARNINg:
Always wear safety goggles or safety glasses
with side shields during power tool operation
or when blowing dust. If operation is dusty, also
wear a dust mask.
Unscrew wing nuts and open the blade cover. Clean saw
dust and wood chips from the blade cover. Close and
secure. (See figure 49.)
Clean plastic parts only with a soft damp cloth. Do
not use any aerosol or petroleum solvents.
wARNINg:
LUBRICATION
Before performing any maintenance, make sure
the tool is unplugged from the power supply and
the switch is in the OFF ( O ) position. Failure to
heed this warning could result in serious personal
injury.
This saw's motor bearings have been packed at the factory
with proper lubrication.
Clean screw threads and nuts with a solvent recommended
for gum and pitch removal.
Lubricate screw threads, nuts, and bearing points
(including those on the blade guard assembly and miter
gauge).
gENERAL
wing nut
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
wARNINg:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Periodically check all clamps, nuts, bolts, screws, and
belts for tightness and condition. Make sure the throat
plate is in good condition and in position.
blade
cover
wing nuts
Fig. 49
ACCESSORIES
The following recommended accessories are currently available at retail stores:
089037006914 Dado Throat Plate
089037006703 Outfeed Support
wARNINg:
Current attachments and accessories available for use with this tool are listed above. Do not use any attachments
or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not
recommended can result in serious personal injury.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTINg
Problem
Solution
Cause
Excess vibration.
Blade is out of balance.
Blade is damaged.
Replace blade.
Replace blade.
Saw is not mounted securely.
Work surface is uneven.
Blade is warped.
Tighten all hardware.
Reposition on flat surface.
Replace blade.
Rip fence does not move smoothly.
Rip fence not mounted correctly.
Rails are dirty or sticky.
Remount the rip fence.
Clean and wax rails.
Adjust clamp screw.
Clamp screw is out of adjustment.
Rip fence does not lock at rear.
Cutting binds or burns work.
Clamp screw is out of adjustment.
Adjust clamp screw.
Blade is dull.
Replace or sharpen blade.
See"Heeling(paralleling)thebladetothemiter
gauge groove" in the Operation section.
Blade is heeling.
Work is fed too fast.
Rip fence is misaligned.
Spreader is out of alignment.
Slow the feed rate.
Align the rip fence.
See "To check and align the spreader/riving
knife and saw blade" in the Assembly sec-
tion.
Replace the wood. Always cut with convex
side to table surface.
Wood is warped.
Check and adjust the rip fence.
Rip fence is misaligned.
Wood edges away from rip fence
when ripping.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTINg
Problem
Solution
Cause
Saw does not make accurate
90˚ or 45˚ cuts.
Positive stops inside cabinet need
adjusting (Bevel Cuts).
Adjust positive stops.
Adjust the miter gauge.
Miter gauge is misaligned (Miter
Cuts).
Height/bevel adjusting hand-
wheel is hard to turn.
Clean the gears or screw post.
Gears or screw post inside
cabinet are clogged with saw
dust.
Plug in motor cord or wall cord.
Motor cord or wall cord is not
plugged in.
Saw does not start.
Replace circuit fuse.
Reset circuit breaker.
Circuit fuse is blown.
Circuit breaker is tripped.
Cord or switch is damaged.
Have the cord or switch replaced at your
Sears Service Center.
Blade makes poor cuts.
Clean, sharpen, or replace blade.
Replace with correct type.
Blade is dull or dirty.
Blade is wrong type for cut being
made.
Remount blade.
Blade is mounted backwards.
Move locking lever to left.
Blade does not lower when
turning height/bevel adjusting
handwheel.
Locking lever is not at full left
position.
Blade cover is dirty.
See cleaning instructions in the Maintenance
section.
Blade not proper for rip cut.
Change blade; rip blade typically has fewer
teeth.
Motor labors in rip cut.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
wARRANTY
RIDgID® HAND HELD AND STATIONARY POwER TOOL
3 YEAR LIMITED SERVICE wARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
wHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION gUARANTEE POLICY
RIDgID, INC. AND ONE wORLD TECHNOLOgIES, INC.
MAKE NO wARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POwER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS wARRANTY.
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
wHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE wARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOw TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One world Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
10 in. TABLE SAw
R4516
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering
repair parts, always give the following information:
R4516
Model No.
Serial No.
987000-415
8-24-09 (REV:04)
Download from Www.Somanuals.com. All Manuals Search And Download.
|