DSP-3
Digital Signal Processor
Amplifier Accessory Hardware Manual
TD-000087-00
Rev.D
*TD-000087-00*
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Warnings, Explanation of Graphical Symbols, and FCC Statement..............................................................4
Section 1: INTRODUCTION
Overview......................................................................................................5
General Use Guidelines..................................................................6
QuickStart Guide............................................................................7
Connector & Indicator Descriptions, Illustrations.................12
Hardware Features and Functions...........................................14
Block Diagram..........................................................................................16
Technical Overview..................................................................................17
Section 2: INSTALLATION
Unpacking..................................................................................................18
What is Included...................................................................................18
Mounting to QSC DataPort Equipped Amplifiers..................................18
Mounting to the Accessory Remote Mounting Bracket......................19
Connecting Audio Inputs and Outputs...................................................20
Connecting to the DataPort of the DSP-3.................................................21
Connecting to RS-232 Port........................................................................21
Daisy-chaining the DSP-3 Outputs.........................................................22
Connection to Accessory External DC Power Supply.................22
Applications Examples....................................................................23
Section 3: SIGNAL MANAGER SOFTWARE
System Requirements...........................................................................26
Software Installation...........................................................................26
Section 4: SPECIFICATIONS.........................................................................................................................................27
Section 5: ARCHITECT’S & ENGINEER’S SPECIFICATION.....................................................................................29
Section 6: APPENDIX
DataPort Pinout.........................................................................................30
RS-232 Pinout ............................................................................................31
Terminal Block Connector Part Number Reference.............................31
Application Information...............................................................32
Preset Operation Notes.................................................................................33
Section 7: QSC INFORMATION
Maintenance, Warranty & QSC Contact Information................................34
© Copyright 2001, QSC Audio Products, Inc.
QSC® is a registered trademark of QSC Audio Products, Inc., Costa Mesa, CA
“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
WHILE QSC HAS ENDEAVORED TO DEVELOP AND PRODUCE THE MOST DEPENDABLE AND ROBUST DIGITAL SIGNAL
PROCESSOR (DSP) AUDIO PRODUCT FOR YOUR USE, DUE TO THE UNLIMITED AND POTENTIALLY DESTRUCTIVE (TO THE
SOUND SYSTEM) CONFIGURATIONS THAT MAY BE APPLIED TO THE DSP BY THE USER, QSC CANNOT BE HELD RESPON-
SIBLE FOR DAMAGES RESULTING FROM ANY DEVIATION OR FAILURE BY THE USER TO STRICTLY FOLLOW THE RECOM-
MENDATIONS SET FORTH IN THE OWNER’S MANUAL FOR THE INTEGRATION OF THE DSP-3 AND SIGNAL MANAGER
SOFTWARE WITH YOUR SOUND SYSTEM.
ALL RISKS ATTENDANT TO INTEGRATION OF USER-CONFIGURABLE DSP PRODUCTS WITH YOUR SOUND SYSTEM ARE
ASSUMED BY YOU. WHILE QSC STRIVES TO SUPPLY THE HIGHEST QUALITY TECHNICAL SOLUTIONS FOR DIGITAL SIGNAL
PROCESSING, IN NO EVENT WILL QSC OR ITS SUPPLIERS BE HELD LIABLE FOR ANY DAMAGES, CONSEQUENTIAL,
INCIDENTAL, OR OTHERWISE, INCLUDING ANY CLAIMS FOR LOST PROFITS AND/OR SAVINGS RESULTING FROM ANY
ATTEMPTED INTEGRATION OF THE DSP-3 AND SIGNAL MANAGER SOFTWARE WHICH DOES NOT STRICTLY ADHERE TO
THE MANUAL’S RECOMMENDATIONS.
IMPORTANT SAFETY INFORMATION: PLEASE REVIEW!
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsu-
lated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric
Federal
Communications
shock to humans.
Commission (FCC)
The exclamation point within an equilateral triangle is intended
to alert the users to the presence of important operating and
maintenance (servicing) instructions in the literature accompa-
Information
NOTE: This equipment has been tested
nying the product.
and found to comply with the limits for a
ClassBdigitaldevice,pursuanttoPart15
CAUTION
of the FCC Rules. These limits are de-
RISK OF ELECTRIC SHOCK
DO NOT OPEN
signed to provide reasonable protection
against harmful interference in a com-
mercialinstallation.Thisequipmentgen-
erates, uses, and can radiate radio fre-
quency energy and, if not installed and
usedinaccordancewiththeinstructions,
may cause harmful interference to radio
communications.Operationofthisequip-
ment in a residential area is likely to
causeharmfulinterference,inwhichcase
the user will be required to correct the
interference at his or her own expense.
CAUTION: To reduce the risk of electric shock, do not
remove the cover. No user-serviceable parts inside.
Refer servicing to qualified service personnel.
WARNING: To prevent fire or electric shock, do not
expose this equipment to rain or moisture.
SAFEGUARDS
Electrical energy can perform many useful functions. This unit
has been engineered and manufactured to assure your personal
safety.Improperusecanresultinpotentialelectricalshockorfire
hazards. In order not to defeat the safeguards, observe the
following instructions for its installation, use and servicing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Overview
The DSP-3 is a digital signal processor (or DSP ) accessory for
audio power amplifiers designed to reduce the need for exter-
nalsignalprocessingwhileincreasingoverallsystemreliability
through distributed intelligence. It is intended primarily for
QSC’s CX, DCA, and Powerlight2 series amplifiers and mounts
directlytotherearpanelofthe2-RU,2-channelmodelsofthese
amplifiers. Pre-August, 1999 date-code of the CX, DCA and
Powerlight2, and all ISA models will require use of an external
power supply. Use of the DSP-3 with Powerlight models
requires remote mounting, external power supply and use of a
specialinterconnectcable(PL6.0/9.0only). RefertotheAppen-
dix for application information. The DSP-3 can also be used
with amplifiers that do not have a QSC DataPort (older QSC
models, non-QSC models) with a reduced feature set and
“remote” mounting/external power.
3 is mounted remotely on a rack-mount accessory that provides
a solid physical mounting platform.
Connections include three D-sub type connections; a DB-9
connector acts as the RS-232 interface and an HD-15 through-
connector provides the DataPort interface to the amplifier and
other QSC DataPort products (if used). The “exposed” side has
four terminal block connectors; 2 audio inputs and 2 post DSP
outputs. There is also a power receptacle for using the DSP-3
with amplifiers that do not provide the required power through
theirDataPort,suchastheISA-series, olderQSCamplifiers and
non-QSCamplifiers. TherearetwoLED’s;ablueonetoindicate
power status and a green one to indicate the presence of an
input signal to the DSP-3.
Control of the DSP-3 is accomplished with the supplied QSC
Signal Manager software. Networked control using the
QSControl platform is also possible (refer to QSControl docu-
mentationfordetails). Pleaserefertothesoftwaredocumenta-
tion (software Help file and Readme.txt file) for feature-set and
operation information. This software provides an easy-to-use
graphical user interface where DSP “objects” are placed onto
apaletteandinterconnectsaredrawn.Thisinterfaceallowsfor
almost infinite configuration possibilities.
The signal processing capabilities include an Input Com-
pressor-limiter,multipleParametricFilters,High-andLow-Pass
Filters, a Shelf Filter, Muting, Attenuation, Multiple Delays,
Polarity Reversal, Audio Routing and Post Crossover Audio
Mixing. Analog-to-digital and digital-to-analog converters are
24 bit resolution, 48 kHz. sampling rate. Additionally, the post-
DSP output signals are daisy-chainable for connection to a
second amplifier. Input sensitivity is selectable and dynamic
rangeisgreaterthan93dB.Inputsandthepost-DSPoutputsare
electronically balanced. See Hardware Features for complete
listing.
Connection of the DSP-3 to the host computer is made by
connectinga serialcablebetweentheDSP-3’sRS-232portand
the host PC’s available COM port. Once the DSP-3 has been
setup as desired and the configuration saved to the DSP-3,
connection to the PC is no longer required. This feature allows
essentially tamper-proof amplifier DSP setup. Further changes
can be implemented in the field by simply connecting a PC (i.e.
laptop computer) and loading the new setup into the DSP-3.
Physically, the DSP-3 is a small module that “piggybacks”
ontothebackpanelofthespecifiedQSCamplifiers. Itconnects
directly to the DataPort on the back panel and is secured with
supplied hardware. When used with other amplifiers, the DSP-
Note: Powerlight 6.0 and Powerlight 9.0 amplifiers require that pin #9 be removed from the remote
mounting interconnect cable. Amplifier damage may result from use of cable that has pin #9 connections present.
Normal VGA computer monitor cables have pin #9 removed and are usable. Check before use!
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- DSP-3 General Use Guidelines
IMPORTANT! Pleas read before operating the DSP-3
with your audio system.
TheDSP-3isaprofessionallevelDSPproductthatallowsthe
user to produce virtually unlimited signal processor varia-
tions and configurations. Because of the infinite configura-
tion possibilities of digital signal processing and the DSP-3,
it is possible to create configurations that may result in
unwanted signals or uncontrollable output
Signal Manager has no way of knowing if the DSP configu-
ration you have designed will produce the results you intend
toproduce. Youcancreatesignalloopsinyourconfiguration
that may oscillate and you may damage your sound system
ifyouapplysuchconfigurationstotheDSP-3. Whenapplying
an untested configuration or when designing or experiment-
ing with the DSP-3, it is a very good idea to turn down the
amplifier’s physical gain controls. That way, you won’t
damageyourspeakersorcreateveryloudsoundsifyouapply
a configuration that doesn’t do what you thought it would.
As a general rule, DO NOT CREATE SIGNAL LOOPS! Do not
mix the output of a DSP object back into its own input! There
isnothingusefultoachievebydoingthat,youwillonlycreate
anoscillatorthatcoulddamageyouspeakers. Also,USETHE
SINEANDNOISEGENERATOROBJECTSWITHGREATCAU-
TION! These objects produce signals that can harm your
speakers. Turndownthegain. Ifyoudon’thearasignalwhen
you think you should, DO NOT INCREASE THE GAIN!!! If the
signal isn’t audible at lower levels, there is something else
wrong. Turning up the gain to full exposes you and your
system to the possibility that some loose connection some-
where will suddenly send a full-amplitude signal through
your sound system.
Like all freely configurable signal processing tools, the DSP-
3 will do what the configuration you design tells it to do,
which may not be what you expect it to do, so use caution.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Quick Start
This quick start section is for those users who want to get up and running with the DSP-3 and Signal Manager
software as quickly as possible. It is in no way a substitute for reviewing the contents of the entire hardware
manual. Itisintendedforpeoplefamiliarwiththeequipmentdiscussedandshouldbefollowedupwithareview
of the manual and the software help file.
This is the same material covered in the Signal Manager software help file, only presented on paper so that you
may “get right to it”.
1
TURN THE EQUIPMENT OFF & INSTALL THE HARDWARE
If you are using the DSP-3 with.......
Then you need to.....
QSC Powerlight2, CX, DCA 2-channel, 2-RU am-
plifiers (or later direct-mount applications)
Mount the DSP-3 to the amplifier by plugging it into the amp’s DataPort and
securing it with the supplied hardware. External power may be required for
older models (see Appendix).
Mount the DSP-3 remotely and connect a QSC DataPort cable between the
amplifier’s DataPort and the DSP-3’s “backside” DataPort. External power
may be required for older models (see top of page 2).
QSC 4-channel CX & DCA amplifiers (or later
models with full-featured DataPort that do not
support direct mounting of the DSP-3)
Mount the DSP-3 remotely and connect a MODIFIED QSC DataPort cable
(male-to-femalecablewithpin#9removed)betweentheamplifier’sDataPort
and the DSP-3’s “backside” DataPort. Connect the external power supply to
the DSP-3’s EXTERNAL POWER jack.
QSC Powerlight 6.0 or Powerlight 9.0
Mount the DSP-3 remotely and connect a QSC DataPort cable (male-to-
female)betweentheamplifier’sDataPortandtheDSP-3’s“backside”DataPort.
Connect the external power supply to the DSP-3’s EXTERNAL POWER jack.
QSC Powerlight, all except 6.0 & 9.0
a non-DataPort amplifier (QSC USA, PLX or non-
QSC models
Mount the DSP-3 remotely. Connect the DSP-3’s CHANNEL 1 OUTPUT and
CHANNEL 2 OUTPUT to the appropriate amplifier inputs (see p.18 for
pinouts). Connect the external power supply to the DSP-3’s EXTERNAL
POWER jack.
2
CONNECT THE COMPUTER TO THE DSP-3
Use a 9-pin serial data cable to connect the DSP-3’s RS-232 connector to the computer’s available COM port (the 9-pin serial port
connectoronthebackofthePC).COM1throughCOM4areusablewiththeSignalManagersoftware.COM1isthedefaultportinSignal
Manager;useCOM1foryourconnectionifitisavailable. Ifnot, youwillneedtoselecttheappropriateCOMportintheSignalManager
program after you install it in step 5.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Quick Start
3
CONNECT THE AUDIO INPUTS
Then you need to......
If your using.......
connectyourinputsignalsourcetoterminalblockconnectors
(refer to page 18) and plug the connectors into the CHAN-
NEL 1 INPUT and CHANNEL 2 INPUT receptacles.
the CHANNEL 1 INPUT & CHANNEL 2 INPUT connectors
the DataPort input (QSC CM16a or related products)
connect the DataPort output from the CM16a (or other
related DataPort product) to the DataPort input of the DSP-
3. Use a QSC DataPort cable (male-to-male) for this connec-
tion. Refer to page 19.
4
TURN THE AMP GAIN DOWN, POWER UP THE AMPLIFIER & THE DSP-3
IftheDSP-3requirespowerfromtheaccessoryexternalpowersupply,apply
power to the DSP-3 FIRST, then turn on the amplifier. The power supply must be
plugged into an operational AC power receptacle. Then plug the “barrel” connector
(coaxialpowerplug) fullyintotheEXTERNALPOWERreceptacleontheDSP-3.When
power is properly applied to the DSP-3, the blue POWER LED will be illuminated. Use
aplasticwire-tie(tie-wrap)tosecuretheaccessorypowersupply’scordtotheDSP-3’s
chassis; there is a metal tab on the chassis for this purpose.
If the DSP-3 is powered by the amplifier’s DataPort, the amplifier must be
connected to an operational AC power receptacle. Then turn the amplifier “on” using
its power switch. The blue POWER LED on the DSP-3 will illuminate a few seconds
after the amplifier’s power switch is activated. If the DSP-3’s blue POWER LED does
not illuminate, you may have an older QSC DataPort equipped amplifier that requires
use of the accessory external power supply (refer to the Appendix for complete
application information).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Quick Start
5
INSTALL THE SOFTWARE
1. Place the QSC Signal Manager CD in your computer’s CD drive (typically the D:\ drive). The installation program should run
automatically after several seconds; if it does not, then proceed with step 2:
2. Run D:\Setup.exe (replace D: with the drive letter designator appropriate for your system) and follow the instructions displayed.
3. When the installation is complete, you will be presented with a screen that prompts you to view the “Readme” file. Please take
time to read this- it contains important up-to-date information on the software.
4. After installation, you will have an icon on your computer’s “desk top” labeled Signal Manager. Use this icon to start the
application (double-click on the Signal Manager icon, this will start the program).
5. Using the Menu Bar (see below) at the top of the window, choose the “Help” item and read the software help section. The help
system includes the contents of this hardware manual for “paperless” reference.
6. IMPORTANT! The DSP-3 is shipped with all of its presets configured to pass full-range audio signals through both channels.
THIS MAY NOT BE APPROPRIATE FOR YOUR SETUP! Be sure to configure any necessary crossovers , filters, etc. prior
to applying audio signals to the inputs. Damage to equipment may result if these recommendations are not followed.
WHAT THE SIGNAL MANAGER APPLICATION LOOKS LIKE
This screen-shot is what a typical Signal Manager “configuration” looks like (example only):
TITLE BAR
MAIN PALETTE
DRAWING TOOLS PALETTE
FILTERS PALETTE
INPUTS AND OUTPUTS PALETTE
MISC PROCESSORS PALETTE
DSP TOOLS PALETTE
MENU BAR
FILE VIEW PANE
WORKSPACE PANE
CURSOR POSITION PANE
RESOURCE METER PANES
SPLITTER BAR
STATUS BAR
CAPS LOCK INDICTAOR
NUM LOCK INDICATOR
CONFIGURATION STATUS PANE
COMMUNICATION STATUS PANE
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Quick Start
6
ESTABLISH COMMUNICATION BETWEEN THE DSP-3 & THE COMPUTER
At this point, you should have everything “up and running”. In the Signal Manager application, check the
COMMUNICATION STATUS PANE (lower right corner of the Signal Manager window, see above).
If the COMMUNICATION STATUS PANE indicates.....
Then you need to......
ONLINE
Do nothing! Your communication settings match the COM port
you connected the DSP-3 to.
Select Tools from the Menu Bar, select Options; the Options
dialog box will open. Click on the DSP tab. In the Serial Port
Selection field, click on the “down arrow” next to the port
selectiondatawindow.AdropdownlistofCOM1throughCOM4
willappear.SelecttheCOMportnumberthatcorrespondstothe
COM port of your computer that the DSP-3 is connected to. Click
OK (at the bottom of the dialog box); the dialog will close. Exit
Signal Manager and restart it so that the newly selected
COM port will become active. The Communication Status
pane should now indicate ONLINE if everything was connected
and set up properly.
OFFLINE
7
ENSURE THE AMPLIFIER IS TURNED DOWN AND THAT YOU HAVE SUITABLE
SPEAKERS CONNECTED FOR YOUR INTENDED CONFIGURATION
For familiarization with the DSP-3 and the Signal Manager software, we recommend that you use a pair of full range
speakers connected to your amplifier and that the amplifier gain be reduced to the minimum useful setting. This will
allow you to configure the DSP-3 almost anyway you desire while providing audio output to verify that the DSP-3 is
doing as you intend. Small, high-power rated monitor speakers are perfect for the task.
Better safe than sorry! Don’t turn you amp all the way up; if communica-
tions between the computer and DSP-3 fail for any reason, unexpected
output transients could damage your speakers
8
CREATE A SIMPLE DSP CONFIGURATION
n
From the Menu Bar, select Configuration, New. If there was a default configuration on the Workspace, you will be prompted to close
the “current” configuration first.
n
Locate the Inputs and Outputs palette; left-click on the icon labeled IN1. Move your pointer into the upper left area of the Workspace
and left-click the mouse again. The IN1 object should now be on your workspace.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Quick Start
n
Now select the OUT1 icon from the same palette (left click on the OUT1 icon). Move your pointer into the upper right area of the
workspace, in line with the IN1 object you just placed, and left click again. The OUT1 object should appear.
n Select the GAIN icon in the MISC PROCESSORS palette (it looks like a little wedge and is the left-most icon in this palette). Move your
pointer to the workspace in between (and in line with) the IN1 and OUT1 objects; click the mouse button again. The GAIN object should
appear.
n
Go to the DRAWING TOOLS palette and select the DRAW (pencil) icon. Notice that the IN1 object has a small yellow-colored “node”
on its right side. This is its connection node or the point that “wires” are drawn from. Similarly, note the same yellow-colored nodes on the
GAIN and OUT1 objects. Draw a “wire” from the IN1 object to the left side of the GAIN object. Draw another “wire” from the GAIN object
(right side) to the OUT1 object.
The DRAW tool works by clicking on one of the nodes that you want to draw a wire between, then, while holding down the
mouse button, dragging the wire to the other node. You can change the drawing mode from click-drag-release wiring to
click-clickwiringintheTools,Optionsdialogbox;selecttheDrawingtabandmakeanydesireddrawing“behavior”changes.
n
When everything is placed on the workspace and connected with “wires”, go to the Menu Bar and select Configuration, then Apply
toDSP(orjustclickonthe“ApplytoDSP”iconintheDSPToolspalette).Thiswillsendyourconfiguration(andanyobjectparametersettings)
fromthecomputertotheDSP-3. TheDSP-3’soutputswillbemutedwhiletheconfigurationisloaded. Forcomplexconfigurations, thiscould
take several seconds.
n If you have active audio inputs connected to the DSP-3 and the amplifier’s gain is sufficient, you will probably hear your audio material
at this point. If not, double-click on each of the GAIN objects and increase the gain setting as required. Also in the Tools, Options dialog,
the DSP tab has settings for input and output sensitivity for the DSP-3; these may require adjustment dependant on your particular set up.
n
The Communication Status pane should indicate “ONLINE” and the Configuration Status pane should indicate “ACTIVE”. If you get
an error message when applying the configuration to the DSP-3 (i.e. “Failed to connect to DSP-3”) check the cable connection between the
DSP-3 and the computer’s COM port. Ensure that the correct COM port is selected in Signal Manager’s Tools, Options, DSP settings dialog
box.
n
Repeat the above procedure, this time using IN2, OUT2 and a GAIN object. This will give you a signal path with gain adjustment for
channel 2. Be sure to “Apply to DSP”. This sends your updated configuration from your computer to the DSP-3.
Thelastappliedconfigurationthatis“running”intheDSP-3whenitisturnedoffbecomestheactiveconfigurationagainonce
thepoweristurnedbackontotheDSP-3. Thisensuresthatthesystem“comesup”justasitwasleftlasttimeitwaspowered
down.
If you decide to edit an existing configuration, you will need to “unlock” the configuration after opening it. Just select
Configuration from the Menu Bar, then select Edit. The palettes that were “grayed out” will now appear in their normal,
coloredstateandyouwillbeabletoedittheconfiguration.Afteryoureditingiscomplete,selectConfigurationfromtheMenu
Bar and then Apply to DSP.
That’s it for the “Quick Start”. For more information, review this manual and the software’s help file.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Basic Connector & Indicator Descriptions
FRONT PANEL
CH1OUTPUT,CH2OUTPUT--These terminal-
CH1INPUT,CH2INPUT-Theseterminal-block
jacks (receptacles) are where you connect the
line-level audio inputs to the DSP-3.
blockjacksprovidespost-DSP(processed)signal
from the DSP-3 for downstream devices (ampli-
fiers, monitoring busses, daisy-chaining the pro-
cessed signal to a second amplifier). In the case
of non-DataPort amplifiers, these are the DSP-3
output that gets connected to your amplifier’s
input connector.
They are electronically balanced with an input
impedanceof8.3kOhm. Ifusedinanunbalanced
configuration,theinputimpedanceis3.7kOhms.
SIGNALindicator-Thisgreen
LED illuminates when the
DSP-3detectsaninputsignal
oneitherchannel. Dualbright-
ness levels indicate signal
level. At -40dB, it will light
dimly; at -20dB it will light
brightly.
EXTERNAL POWER-
2.5mmbarrelconnector-
Center (+), Outer(-), 15
VDC, 300mA. Use only if
your amplifier does not
supply the required op-
erating voltage from its
DataPort (or non-
DataPort amps).
DATAPORT- This is the “in-
put” DataPort. If the DSP-3 is
used with QSC DataPort prod-
ucts that can supply the audio
inputsorprovideamplifiercon-
trol&monitoring, thisiswhere
they are connected to the DSP-
3.
RS-232- This DB-9 fe-
male jack is where the
serialcablebetweenthe
DSP-3andthecomputer
is plugged in.
POWER indicator- This blue
LEDilluminateswhentheDSP-
3 has power properly applied.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Basic Connector & Indicator Descriptions
REAR PANEL
DATAPORT (unlabeled)- This is the “output”
DataPort.
If the DSP-3 is directly mounted on a 2-RU QSC
DataPortequippedamplifier, thisconnectorplugs
into the amplifier’s DataPort connector.
If used with 3-RU QSC DataPort equipped amplifi-
ers, the DSP-3 will need to be remotely mounted
and a male-female DataPort cable used to inter-
connect the amp & DSP-3.
If used with a non-DataPort amp (QSC or other),
this connector will not be used.
OVERALL
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- List of Functions & Features
DSP-3 Hardware Features (full set available to QSC DataPort equipped amplifiers):
High- and Low-Pass Crossover
Selectable responses:
Butterworth (6,12,18 or 24 dB per octave slope)
Bessel (6,12,18 or 24 dB per octave slope)
Linkwitz-Riley (12 or 24 dB per octave slope)
Graphical response curve provided in software
Adjustable frequency & slope
Ability to bypass all EQ with a single mouse click
Ability to add or delete EQ
Assignable anywhere in signal chain
High- and Low-Pass Shelf Filter
Adjustable corner frequency
Adjustable Q factor
Adjustable gain
Graphical response curve provided in software
Ability to bypass all EQ with a single mouse click
Ability to add or delete EQ
Assignable anywhere in signal chain
Output Peak Limiter
Adjustable threshold
Adjustable attack time
Adjustable release time
Graphical response curve provided in software
Ability to quickly bypass limiter with a single mouse click
Assignable anywhere in signal chain
Multiple Delays
910 millisecond maximum ( sum of all delay objects)
20.83 microsecond increments
Entry can be in seconds, feet or meters
Assignable anywhere in signal chain.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- List of Functions & Features
Parametric EQ
Adjustable frequency
Adjustable gain
Adjustable Q factor
Ability to bypass all EQ with a single mouse click
Ability to add or delete EQ
Graphical response curve provided in software
Assignable anywhere in the signal chain
Signal Compressor
Adjustable attack and release times
Adjustable Gain
Adjustable threshold
Adjustable compression ratio
Graphical response curve provided in software
Assignable anywhere in the signal chain
Signal Level Meter
Peak or rms response
Signal Attenuation (mute or bypass)
Mix Post Crossover Audio (2 to 1 mixer with mute and lock all channels featured)
Signal Splitter
External Contact Closure Sensing (pin #9 of RS-232, operates with ”Switched Gain” objects in Signal Manager software)
Pink & White Noise Generator
Variable Frequency Tone Generator
Clip & Protect Indication
Signal Polarity Reversal
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Block Diagram
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction- Technical Overview
This portion of the introduction provides some of the technical details of the DSP-3.
Audio Input Path
to non-QSC amplifiers (or any amplifier that does not have a
There are two audio channels each with two input connectors, a
balanced 3-pin ‘euro’ terminal block jack and an electronically
balanced DataPort input. The inputs are protected with a filter that
prevents radio frequency interference. The inputs have software-
selectablefullscaleinputlevelsensitivity; thisisthelevelatwhich
the analog to digital converters reach their full scale digital value.
Refer to the Specifications section for full details. The DataPort is
scaled to clip with a full scale digital input if the DSP-3 does not
change gain structure. Each CODEC input is diode protected to
prevent any large signal from destroying its inputs.
DataPort). External power is provided by the accessory power
supply (“wallwart”)viaacoaxialpowercordjackonthebackofthe
DSP-3.
When using the external power source, we recommend
that the DSP-3 be powered-up before the amplifier in order
to insure trouble-free start-up. This will also avoid the
possibility of “thumps & bumps” should the DSP-3 be pow-
ered up after the amplifier.
Audio Output Path
Data Acquisition
The first stage the audio passes through is an inverting gain stage.
The second stage is a second order Butterworth low pass filter that
removes high frequency sampling artifacts. The signal is then sent
out of the DSP-3 through the DataPort or the output ‘Euro’ connec-
tors. The output level is selectable in software.
The DSP-3 samples the IMON and VMON (current and voltage monitor-
ing from the amplifier) lines of QSC amplifiers (via the DataPort) in
order to perform dynamics (limiter, compressor, etc.) processing.
The four inputs (IMON and VMON for both channels) are continuously
sampled by a four channel ADC. When used with non-QSC
amplifiers or QSC amplifiers that have no DataPort, the
power limiter DSP “object” is not available as this function
relies upon amplifier current and voltage feedback. The
DSP-3 will also not be able to monitor the protect or power status
of the amplifier as these features require amplifier data via a
DataPort connection.
Power Supply
No external power supply is needed for use with the CX, DCA and
PL2two-channel, 2RUseriesamplifiersproducedwith date-codes
of August, 1999 or later. With these models, the DSP-3 is supplied
powerfromthe amplifier viatheDataPort(HD-15)connection. CX,
DCA, and PL2 amps made prior to August 1999 DO NOT
provide adequate power supply voltage to the module,
requiring the use of the same type of external DC supply as
used with Powerlight amplifiers. The amps in question will have a
serial number PRIOR to 0899XXXXX, where the first four digits of
the serial number are the MMYY datecode. Again, the modules
WILL work with these amps just fine, but will require the use of our
external power supply. External power is not required for all other
directly-mounted-to-amplifiersituations.
Contact Closure
One contact closure input is provided. It uses pin 9 of the RS-232
DB-9 connector (not normally used for RS-232). Shorting this pin to
ground with a maximum impedance of 1.3 kOhms will cause a
general purpose I/O pin of the DSP to be pulled to a logic low. The
currentreleaseofSignalManagersoftwareusesthisinputtoallow
switched gain functions. Each of the Switched Gain blocks will be
switched simultaneously by the single contact closure (switch).
EachSwitchedGainblockhasatwogainsettings;oneforopenand
one for closed switch conditions.
When used with the Powerlight series of amplifiers (or 3 RU & 4-
channel amps), the DSP-3 requires use of the accessory external
supply.Theaccessoryexternalsupplyisalsousedwhenconnecting
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Unpacking and Mounting
UNPACKING
TherearenospecialunpackingprecautionsfortheDSP-3. However, itisrecommendedthatyoukeeptheoriginalpackingmaterialforreuse
in the rare event that service be required for your DSP-3. If service is required and the original packing material is not available, insure that
the DSP-3 is adequately protected for shipment (strong box of appropriate size , sufficient packing material).
WHAT IS INCLUDED IN THE CARTON:
Item
1-
Description
Quantity
DSP-3 Digital Signal Processor
3-pin terminal block connector plug
#4-40 machine screw, 1.125” long
#8-32 machine screw, 0.312” long
Hardware Manual (this document)
Signal Manager Software CD disk
1
4
2
1
1
1
2-
3-
4-
5-
6-
DIRECT MOUNTING THE DSP-3 TO 2-CHANNEL, 2 RU QSC DATAPORT EQUIPPED AMPLIFIERS (CX, DCA, Powerlight2)
The DSP-3 mounts directly to the rear of 2-channel, 2-RU, DataPort equipped QSC amplifiers.
1- Configure the amplifiers DIP switches (QSC amplifiers where the DSP-3 covers the configuration switches) as follows:
•All filters off
•Clip limiter off
•Mode set as required
2- Align the DataPort plug on the back of the DSP-3 with the DataPort jack on the back of the amplifier and gently push the DSP-3 to seat
the connector.
3- Install the two #4-40 screws to secure the left side of the DSP-3 to the amplifier. These two long screws pass through the DSP-3 and
thread into the inserts on the DataPort (HD15) jack. (see below). Use a #1-size phillips driver; be sure not to overtighten.
Be sure to secure the DSP-3 using all three mounting screws. The DSP-3’s “backside” DataPort connector can be
easily damaged if the DSP-3 is twisted and there are no supporting screws to properly secure it to the chassis.
4- Install the #8-32 screw (0.312 inch long) to secure the right side of the DSP-3 to the amplifier (see below).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Remote mounting (4-ch., Powerlight & non QSC amp’s)
REMOTE MOUNTING THE DSP-3 : 4-Channel CX and DCA , Powerlight series, and all non-QSC amplifiers
Use of the DSP-3 with the 4-channel CX and DCA and all Powerlight amplifiers requires the remote mounting of the DSP-3. Use with non-
QSC amplifiers also requires remote mounting. Keep in mind that all applications that use amplifiers that do not have a DataPort ( i.e. non-
QSC amplifiers) some of the dynamic processing capabilities of the DSP-3 will not be available.
Accessory Remote Mounting Bracket- This accessory is a 19”, 2-RU panel with mounting facilities for up to four DSP-3 modules. It is
intended to be mounted to the rear-support rails of an equipment rack. The bracket kit comes with one large bracket ( the 19”, 2-RU size)
and four smaller right-angle brackets that are used for securely mounting up to four DSP-3’s in a 2-RU space. Adjustable rack ears are
included for maximum mounting flexibility.
1- Attach the right-angle bracket to the DSP-3 module. The right-angle bracket is attached as shown, below.
2- Attach the DSP-3 & right-angle bracket to the main 19” bracket as shown, below.
3- Mount the main bracket assembly in your equipment rack
between the rear support rails.
4- Attach the inputs, outputs, DataPorts,
RS-232 and external power as required.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Connections
CONNECTING AUDIO INPUTS AND OUTPUTS:
The audio inputs and outputs of the DSP-3 use 3-pin “Phoenix”-type (Euro-style) terminal block connectors. These connectors allow pre-
wiring of inputs without any soldering and allow for rerouting of audio inputs by simply interchanging connector locations without the need
for any tools. See Appendix for connector manufacturer’s part number reference.
Inputs- The audio input can be from one of two sources; the front-panel DataPort OR the terminal-block
INPUT connectors.
Do not use both sets of inputs at the same time! Use balanced connections
for the lowest possible noise levels and for minimizing the possibility of hum inducing ground loops.
Outputs-The DSP-3’s post-DSP (processed) audio is output to the rear-panel DataPort ANDthe terminal-
block OUTPUT connectors.
The OUTPUT’s can be used for daisy-chaining the processed audio to
additional amplifiers, even when connected to a DataPort-equipped amplifier via the rear-panel DataPort.
Balanced connection is recommended for all inputs.
The terminal block inputs on the DSP-3 are electronically
balanced. Balanced input cables are recommended to mini-
mize noise pick up and prevent ground loops.
Unbalanced inputs can be used if required. If unbal-
anced audio sources are used, it is preferable to use an
appropriate audio transformer (or other unbalanced-to-bal-
anced “converter”) to provide a balanced input to the DSP-3.
Ifthisisnotpossible,thenitisrecommendedthatthenegative
terminalandshieldterminalbeconnectedtooneanotherwith
a jumper wire.
Withtheconnectororientedasshownattheright,connectthe
positive (+) signal wire to the left-most
Toconnectyoursignalwiretotheterminal-blockplug-backthescrewsout
a few turns to open the wire-clamp, carefully insert the conductors into the proper
location, and retighten the clamping screw.
The recommended stripping length for the wires is approximately 6 to 8
mm ( 1/4 to 5/16 inch). When stripping the audio cable, be careful not to nick or
cut the conductor strands. After each conductor has been stripped and dressed,
insert it fully into the connector and tighten the retaining screw. When stranded
wire is used, carefully twist the conductor strands together so that when they are
inserted into the connector assembly, no loose strands short adjacent terminals.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Connections
DATAPORTConnection-Thissectionappliestothoseusersinterfacing
withtheQSCDataPortproducts.IfusingtheDataPortforyouraudioinputs,
DO NOT use the terminal block inputs. If the DataPort is used only for
control&monitoringoftheamplifier(noaudioinputthroughtheDataPort),
then audio input may be via the terminal-block connectors.
The front-panel DataPort connection is used for connecting to
QSC DataPort products. Use a QSC DataPort cable (male-to-
male) similar to VGA computer monitor cables. Do not use com-
puter VGA cables as they are not correctly constructed for
use with the DSP-3. QSC DataPort cables may be obtained
through your QSC distributor or by calling QSC’s Technical Services
Department. The plugs and jacks are the same physical size as the
RS-232 connections; be careful not to get them confused.
The rear-panel DataPort connection from the DSP-3 to QSC
amplifiers is made when mounting the DSP-3 to the rear of the
amplifier. The DataPort connection from any other accessory to the
DSP-3 is made by orienting the connector properly, inserting it fully
into the jack and finger-tightening the retaining screws. The audio
signals on the rear-panel DataPort are post-DSP (processed).
DataPort Connection: 15-pin Cable
Front panel DataPort connection is not required for the operation
of the DSP-3.
RS-232 PORT Connection- Connection to the RS-232 port is made
usinga9-pinserialdatacable(male-to-female).Cablelengthshouldbe25
feetorless.OrienttheDB-9plugcorrectly,inserttheplugfullyintotheRS-
232 port and finger-tighten the retaining screws.
DSP-3 setup and programming takes place through the RS-232 port. Any
time setup changes are required to the DSP-3, it must be connected to its
host computer through the RS-232 port. If “real-time” control of the DSP-
3 is required, the RS-232 port connection must be maintained as well. If
“real-time” control is not required, then the DSP-3 can be setup first and
then disconnected from the PC.
The RS-232 connection does not have to be maintained for the
DSP-3 to operate.
RS-232 Connection: 9-pin Cable
Setup & programming can also be done via Ethernet network
communication when using QSC’s QSControl products. Refer to
QSControl documentation for detailed information.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Connections
DAISY-CHAINING THE DSP-3 OUTPUTS TO ADDITIONAL AMPLIFIERS
The DSP-3 provides audio output jacks for each channel. These outputs may be used for daisy-chaining the post-DSP signal to other
amplifiers or for monitoring purposes. The signal on the output jacks is post-DSP. All signal processing functions done by the DSP-3 effect
the signal provided to the output connectors as well. The terminal block outputs are active even when the DataPort connections are used.
To daisy-chain the DSP output, connect the output jacks of the DSP-3 to the input jacks of the next amplifier. Make sure that
all interconnecting cables are balanced and connected properly.
CONNECTION TO ACCESSORY EXTERNAL DC
POWER SOURCE
When the DSP-3 is used with QSC Powerlight amplifiers
that do not provide the required +15VDC through their
DataPort connection OR is used with non-DataPort ampli-
fiers,powermustbesuppliedtotheDSP-3fromanexternal
power supply.
QSC offers an accessory external power supply for applica-
tions with non-QSC amplifiers or with QSC Powerlight models
QSCoffersanaccessory externalpowersupplyforapplica-
that do not provide the required operating voltage.
tions where a DataPort that provides +15 VDC is not
available. Contact QSC’s Technical Services Department
for details. Although not recommended, third-party ex-
ternal power supplies may work with the DSP-3 provided
they are of the correct voltage, voltage type (DC) , current
rating and polarity. Any damage to the DSP-3 caused by
connection to a non-QSC external power supply is not
covered under the warranty.
Ensure that any external power supply connected to
the DSP-3 is of the proper voltage type, level and
current rating.
Be certain that the connector polarity is correct as
there is no industry standard!
Connection to an improper voltage source can cause
immediate damage to the DSP-3!
Insert the coaxial power plug into the EXTERNAL
POWER jack. Ensure that the plug is firmly seated in
the jack. Use the “tab” provided on the chassis for
securing the power cord with a tie-wrap (wire-tie).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Application Examples
The following examples show basic hook up information that assumes a two-channel, full range audio signal driving the load. Refer to your
amplifier’s hardware manual for other output configurations. All audio signals are line level.
DSP-3 Directly Mounted to QSC Amplifier. Audio Inputs via Terminal Block Inputs
DSP-3 Directly Mounted to QSC Amplifier. Networked OR Local Control. Audio Inputs via DataPort.
NOTE: External accessory power supply may be required on older models, see page 2 for full application information.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Application Examples
DSP-3 Remotely Mounted used with QSC DataPort Amplifier. Audio Input via Terminal Block Inputs
DSP-3 Directly Mounted to QSC Amplifiers, Networked Control via QSCcontrol Products
NOTE: External accessory power supply may be required on older models, see Appendix for application information.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Installation- Application Examples
DSP-3 Remotely Mounted connected to any Non-DataPort Amplifier.
Audio Input via Terminal Block Inputs
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Signal Manager Software- Software Installation
System Requirements- To use QSC Signal Manager, you need the following hardware and software:
• IBM compatible computer, 200 mHz or greater Pentium Processor
• Windows 98/2000/ME or Windows NT 4.0 with service pack 6a or later
• SVGA display at 800 x 600 minimum resolution, 1024 x 768 recommended
• CD-ROM drive
• 32 MB or more of RAM
• 10 MB of free hard disk space
• An available RS-232 serial communications port (COM port) capable of 38.4k baud
• A male-to-female 9-pin serial cable (to connect the DSP-3 to available COM port)
Software Installation-
1. Insert the CD labeled QSC DSP-3 Signal Manager into your CD drive (typically drive “D:”). If your computer has AUTORUN enabled, the
installation utility will start automatically. If it does not, then proceed to step 2, below. Otherwise, proceed to step 3.
2. Run D:\Setup.exe (replace “D” with your CD drive’s designation if necessary) and follow the instructions displayed.
3. When the installation is complete, you will be presented with a screen that prompts you to view the “Readme” file. Please
take time to read this- it contains important information on how to use the software.
4. After installation, you will have an icon on your desk top labeled “Signal Manager”. Use this icon to start the application.
5. Using the main menu bar at the top of the window, choose the “Help” item and read the software help section. The help system includes
6. IMPORTANT!TheDSP-3isshippedwithallofitspresetsconfiguredtopassfull-rangeaudiosignalsthroughbothchannels.THISMAY
NOTBEAPPROPRIATEFORYOURSETUP!Besuretoconfigureanynecessarycrossovers, filters, etc. priortoapplyingaudio
signals to the inputs. Damage to equipment may result if these recommendations are not followed.
OVERALL NOTES AND WARNINGS-
• The last applied configuration that is “running” in the DSP-3 when it is turned off becomes the active configuration again
once the power is turned back on to the DSP-3. This ensures that the system “comes up” just as it was left last time it was
powered down.
• Do not run your amplifier “wide open” (maximum gain) while making real-time adjustments to the DSP-3’s setup. The
nature of the communication path between the PC and DSP-3 is inherently more complex than direct physical controls of
an equivalent analog processing device. Unpredictable results may occur due to failure of the PC or the communications
channel. Under such circumstances, damage to your drivers is possible if the amplifier gain is set for high power levels.
Use the minimum useful gain settings while making system adjustments.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Specifications
Signal Processing 24 bit, 48 kHz.
Common-mode rejection
Crosstalk
>50 dB, 20 Hz–20 kHz
Frequency response
at 3dB below full
scale input voltage
20 Hz–10 kHz 0.3 dB (term. block inputs)
20 Hz–20 kHz 0.7 dB (term. block inputs)
20 Hz–20 kHz 0.2 dB (DataPort inputs)
>75 dB separation, 20 Hz–20 kHz
Distortion
<0.01% THD+N @ +4 dBu out
687.5 microseconds
Outputs
Delay (throughput)
Dynamic range
Program outputs
Connector type
Pinout
2 (via HD-15)
HD-15 DataPort connection
Special, see appendix
QSC DataPort cable
2 meters
>93 dB unweighted
20 Hz–20 kHz, 1.5V, 4V and 9V sensitivity
>88dB unweighted
Cable type
Qualified length
20 Hz–20kHz, 18V sensitivity
Polarity
Mute
In-phase or inverted
>90 dB attenuation
Daisy-chain output
Connector
2 (1 per channel)
“Phoenix-style” (a.k.a.
“Euro-style”) detachable
terminal blocks
Inputs
Program inputs
Connector type
2
“Phoenix-style” (a.k.a.
“Euro-style”) detachable terminal blocks
Type
Grounding
Electronically balanced
Shield terminal connected to
chassis
Type
Grounding
Electronically balanced
All shield terminals connected to
chassis
Output level
(full scale)
6.0 or 4.0 Vrms
18.0 or 14.5 dBu
15.5 or 12.0 dBv
Input sensitivity
1.5, 4.0, 9.0 or 18.0 Vrms
(full scale input level)
6, 14.5, 21.5 or 27.5 dBu
3.5, 12.0, 19.0 or 25.0 dBv
Output impedance
600 Ohms balanced
Units are selectable in software interface
Impedance
8.3 K Ohm balanced
3.7 K Ohm unbalanced
Power amplifier connectivity
Power amplifier interface
Amplifiers
one 2-Ch. amplifier per DSP-3
Compatibility
all QSC and non- QSC amplifiers
Amplifier status monitor
Clip indicator
Full-feature set
Connector and cable
all QSC DataPort equipped amplifiers
Senses channel clipping
Senses amplifier protect status
Protect indicator
(status monitoring not available for non-DataPort amplifiers)
HD-15 VGA cable, 2 meters length
qualified (for longer runs, contact
QSC’s Technical Services Department)
RS-232 Port
Cable Type
9-pin serial cable, male-to-female
25 feet (7.6 meters)
Maximum Length
Contact closure input (sense)
Inputs
Configuration
1 discrete input (pin #9 of RS-232 port)
Single-ended input
Resistance for closure detect <150 Ohms
Resistance for open detect >1.9 K Ohms
TTL Compatible
Maximum Voltage= +9vdc
Note: Specifications are subject to change without notice.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Specifications
General
Physical
Accessory External Power Supply
Height
Width
Depth
3.50 inches
3.75 inches
1.38 inches
AC Input Voltage
AC Input Current
Frequency
80–240 VAC
0.3 Amps rms
50 to 60 Hz
Output Voltage
Output Current
15 VDC
300 milliamperes
Weight
0.59 lbs (0.27 kg)
Output Termination Detachable power cord with 2.5mm
barrel-type (coaxial) connector
Mounting
Direct mount to amplifier or
remote mount
center pin is positive
Operating temperature
0 to 50° Celsius
Note: Specifications are subject to change without notice.
Dimensions
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Architect’s and Engineer’s Specifications
Contact Closure I/O—The DSP shall provide a trigger input
The Digital Signal Processor (DSP) shall provide two independent
channels of DSP for signal delivery to QSC DataPort equipped
poweramplifiers. TheprocessingshallbedistributedwiththeDSP
module mounted directly to the rear of the power amplifiers.
usable for contact-closure (or other) purpose which shall
be CMOS & TTL signal compatible.
Power Supply—The DSP shall be provided power through its
DataPort connection to QSC amplifiers. For older ampli-
fiers or non-QSC amplifiers, a coaxial power jack will be
provided on the DSP for connection to an external power
source. Power required shall be +15 VDC at 300 mA
(max.).
Output Peak Limiter—For each audio channel, the DSP shall
provide a peak limiter that is assignable anywhere in the
signalchainandcanbeswitchedonoroff.Thelimitershall
provide the following adjustments:
Gain
Amplifier Interface—The DSP shall attach directly to the rear of
eachpoweramplifier.TheDSP’sinterfacetoeachpower
amplifierDataPortshallbeviaanHD-15connector. This
interfaceshalltransmittwoamplifierinputaudiosignals
as well as all control and monitoring signals. Special
signal conditioning and grounding techniques shall be
used in this interface to ensure negligible levels of noise
andcrosstalk.Fornon-DataPortamplifiers,thereshallbe
mounting and interface options provided for operating
with the DSP.
Threshold
Attack time
Release time
High- and Low-Pass Crossovers—For each channel of audio,
the DSP will provide high-pass and low-pass crossovers
that are assignable anywhere in the audio chain. The
crossovers must be capable of being switched in or out
of the signal chain. The DSP shall provide the following
crossover responses:
Butterworth (6,12,18,24 dB per octave slope)
Bessel (6,12,18,24 dB per octave slope)
Linkwitz-Riley (12 & 24 dB per octave slope)
Amplifier Output Monitoring—When used with QSC DataPort
amplifiers, the DSP shall provide clipping and protect
status detection at the amplifier’s output terminals.
Noise & Tone Generation-- The DSP shall provide pink and
whitenoisegenerationcapability.Itshallalsoprovidefor
tone generation.
High-andLow-PassShelfFilters—Foreachaudiochannel,the
DSP shall provide high-pass and low-pass shelf filters
that are assignable anywhere in the audio chain. The
shelf filters must be capable of being switched in or out
of the signal chain. The DSP shall provide the following
shelf filter adjustments:
Presets— The DSP shall be capable of storing at least 8 preset
configurations. The control software shall provide man-
agement of these presets.
Variable corner frequency
Variable gain
General—All audio inputs and outputs shall be balanced with a
nominal input level of +4 dBu and maximum level of +21
dBu. Input connectors shall be of the “Phoenix” detach-
able terminal block type.
Variable slope
Compressor-- The DSP shall provide a signal compressor that is
assignable anywhere in the signal chain. It shall have adjustable
threshold, attack time, release time, and compression ratio.
Control— The DSP shall be configurable via RS-232 or via a
networked DataPort connection.
The Digital Signal Processor shall be the QSC DSP-3.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Appendix- DataPort Pinout
DATA PORT PINOUT
The diagram below shows the pin assign-
ments used for the HD-15 connectors on
the DSP-3 and amplifier.
Pin
Signal Description
NOTE!
1
Ch. 1 Minus (-) Input Signal
AC Standby Control
This information is shown for reference
2
only and is subject to change without no-
3
V- MON Ch. 1 and Subcode 1
I- MON Ch. 1 and Subcode 2
Clip/Protect Ch. 1
tice as the DataPort feature is specific to
QSC products and not intended for inter-
face to other manufacturer’s equipment.
4
5
6
Hard Ground
7
Ch. 1 Plus (+) Input Signal
Ch. 2 Plus (+) Input Signal
+15V from Amplifier
8
9
10
11
12
13
14
15
Data Reference Ground
Ch. 2 Minus (-) Input Signal
Amplifier IDR (Model ID)
V- MON Ch. 2 and Subcode 3
I- MON Ch. 2 and Subcode 4
Clip/Protect Ch. 2
Note: Powerlight 6.0 and Powerlight 9.0 amplifiers
require that pin #9 be removed from the remote mounting
interconnect cable.
Amplifier damage may result from use of cable that has pin
#9 connections present.
Description of Encode Signals
encode 1
encode 2
Bridge mode & power detect
Temperature, channel 1
encode 3
encode 4
Standby mode detect
Temperature, channel 2
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Appendix- RS-232 Port Pinout & Connector P-N’s
RS-232 PINOUT: The diagram below shows the pin assignments for the RS-232 connector on the DSP-3.
Note that Pin #9 is used for Contact Closure function (normally not used in RS-232).
Pin
Signal Description
1
2
3
4
5
6
7
8
9
DCD
TD
RD
DTR
Signal GND
DSR
RTS
CTS
contact closure
TERMINAL BLOCK CONNECTOR PART NUMBER REFERENCE- The following manufacturers and part numbers are provided
as a reference to users. The information here is subject to change without the knowledge of QSC.
3 pin without integral strain relief: Phoenix Contact - 17 57 02 2; Riacon - 31249103-6; On Shore Tech - EDZ950/3
3 pin WITH Strain Relief : Phoenix Contact 17 76 16 8
“Phoenix Contact” is the trademark of Phoenix Contact, Inc., Middletown, PA
“Riacon” is the trademark of RIA electronic, Inc., Eatontown, NJ
“On-Shore Technology” is the trademark of On-Shore Technology, Inc., Tempe, AZ
All other trademarks are the property of their respective owners
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Appendix- Application Information
APPLICATION INFORMATION
As design improvements are continuous, the following information is subject to change. Contact QSC for current information.
QSC’sDSP-3ModulehasbeendesignedtoattachdirectlytotheDataPortconnectorofQSC’sCX,DCA,Powerlight,andPowerlight
2 series amplifiers. When attached to CX, DCA, and Powerlight 2 amps manufactured 08/99 and later, the module receives its
power through the DataPort from the amplifier. Modules connected to earlier models of those just mentioned and all Powerlight
amplifiers (the “non-2’s”) require an external DC supply (available from QSC).
TO CLARIFY- CX, DCA, and PL2 amps made prior to August 1999 DO NOT provide adequate power supply voltage to
the module, requiring the use of the same type of external DC supply as used with Powerlight amplifiers. The amps in
question will have a serial number PRIOR to 0899XXXXX, where the first four digits of the serial number are the MMYY datecode.
Again, the modules WILL work with these amps just fine, but will require the use of our external power supply.
•Full feature set, Direct-mounting, No external power or special interconnect cables required for the following QSC
power amplifiers with serial numbers of 0899XXXXX and later, where the first four digits of the serial number are the MMYY datecode :
CX series:
CX302 - CX1202V (all)
DCA series:
PL2 series:
PL2A series:
DCA1222, DCA1622, DCA2422, DCA3022, DCA342
PL224, PL230, PL236, PL218
All
•Remote Mounting Required, QSC DataPort Cable required: Full feature-set, no external power required.
CX series:
DCA series:
CX204V, CX254, CX404
DCA1644, DCA1824
•Remote Mounting, QSC DataPort Cable and External Power required: Full feature-set.
Powerlight series:
PL1.0 through PL4.0 (all)
PL6.0 and PL9.0 require modified DataPort cable between DSP-3 and amplifier.
Powerlight 6.0 and 9.0 MUST have
pin#9removedfromtheAmplifier-to-
DSP DataPort Cable before use!
•RemoteMountingandExternalPowerrequired.NoDataPortConnectionpossible,PowerLimitingnotavailable.
ISA series:
MX series:
PLX series:
RMX series
USA series:
The ISA amplifiers have a “V2” DataPort that may be used for audio inputs only.
All
All
All
All
ALL non-QSC amplifiers are can be used with the DSP-3.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Appendix- Preset Operation Notes
SPECIAL INFORMATION CONCERNING SAVED DSP-3 CONFIGURATIONS
The computer which is used to create the DSP-3 signal flow configurations, and subsequently save them to disk,
should be the same computer used to modify and adjust the DSP-3 settings in the future. Naturally, this might not
always be the case. At the least, a copy of the DSP-3 configuration(s) should be saved to floppy disk, so the
configuration files can be transferred to whatever computer(s) might be used to adjust or modify the DSP-3
module settings in the future.
The reason:
The Signal Manager software works in conjunction with the DSP-3 module to
create specific signal processing algorithms for filters, delays, limiters, and the like. The algorithms are displayed on the
computer screen as ”configuration files”, with graphical representations of each function and parameters. The user creates a
signal chain, “wiring” together blocks of functions as needed for each particular audio channel or channels.
When you build a DSP-3 configuration from scratch, or load one from disk, and perform an “Apply to DSP” operation, the
information downloaded into the DSP-3 module is NOT the graphical representation of what is displayed on the screen. The
downloaded information consists of the compiled algorithm coefficients of the functions, i.e. “just the math”. If building a new
configuration from scratch, when you apply it to the DSP-3 you will also be prompted to save it to disk as a Configuration file.
The path for this Configuration file is then associated with the compiled information that is applied to the DSP-3. A previously
saved(todisk)configurationfilemayalsobeappliedtotheDSP-3, andthatparticularfilepathisassociatedwiththealgorithms
now loaded in the DSP-3.
When you connect a DSP-3 to a computer, the Signal Manager software first attempts to locate and display the configuration
file that has been associated with the algorithm coefficients currently running in the DSP-3, to correlate “what you hear” with
“what you see”. This would allow you to further adjust a delay or a filter parameter, for instance. If the correct file is located,
based on the associated path name, the graphical configuration is displayed. If the file is not found (the file has been renamed,
moved,deleted,oryouarenotusingthesamecomputeronwhichtheDSP-3wasoriginallyconfigured)thecomputerwilldisplay
a message asking if you would like to load the Default configuration.
Answering YES will load the Default (factory) configuration TO THE SCREEN, but will not apply it to the DSP-3. Answering NO
will merely display a blank workspace to the screen with no configuration loaded. At this point, what is displayed is NOT what
is currently running in the DSP-3 memory.
IFYOUPERFORMAN“APPLYTODSP”NOWYOUWILLOVERWRITEWHATEVERISCURRENTLYRUNNINGINTHEDSP-3! This
is likely NOT what you want to do. Instead, locate the desired configuration file (from an alternate path or from floppy) using
the Configuration->Open menu (Ctrl-O).
When the proper configuration file is displayed on the screen, go to the Configuration->Edit menu (Ctrl-E), followed by an Apply
to DSP command (Ctrl-D). This will download the currently displayed configuration back into the DSP-3 (overwriting itself),
allowing synchronization of what is displayed with what is running in the DSP-3. At this point, you may adjust parameters or
modify settings as usual.
QSC engineers are currently developing an improvement to this process, in which the computer would always be capable of
displaying the currently running configuration, regardless of the location of the configuration file (or lack of the file).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Maintenance, Warranty & QSC Contact Information
Disclaimer
Cleaning
QSC Audio Products, Inc. is not liable for any damage to speakers,
amplifiers, or any other equipment that is caused by negligence or
improper installation and/or use of the DSP-3 digital signal proces-
sor.Duetotheinherentcomplexityofthecommunicationsbetween
the DSP-3 and the host computer, QSC Audio Products, Inc. is not
liableforanydirectorindirectdamagecausedbycomputercommu-
nications failure.
The faceplate and chassis can be cleaned with a soft cloth and
nonabrasive, mild cleaning solution. Products like Simple Green
andWindexworkwell.Donotusepowdersorscrubbingpadsofany
type as they are usually abrasive and will permanently damage the
finish of your DSP-3. Dampen a soft, lint-free cloth with the
cleaning solution and wipe the DSP-3 down gently. Insure that
cleaning solution does not get down into the connectors. Do not
spray the solution directly onto the DSP-3 as it will penetrate into
the connectors.
Product Warranty
QSC guarantees the DSP-3 to be free from defective material and/
orworkmanshipforaperiodofthreeyearsfromthedateofsale,and
will replace defective parts and repair malfunctioning products
under this warranty when the defect occurs under normal installa-
tion and use—provided the unit is returned to our factory via
prepaid transportation with a copy of the proof of purchase, i.e.,
sales receipt. This warranty provides that examination of the
returned product must indicate, in our judgment, a manufacturing
defect. This warranty does not extend to any product which has
been subjected to misuse, neglect, accident, improper installation,
or where the serial number and date code have been removed or
defaced.
User Maintenance
There is no user-level maintenance on the DSP-3. Contact QSC’s
Technical Services Department if service is required.
Warranty Information
If the DSP-3 isn’t working properly, please verify that a
known good 9-pin serial cable is used between the DSP-3
and the computer. If proper operation can not be restored,
the DSP-3 may require service. This must be performed by
qualified service personnel. To obtain the location of you
nearest QSC Authorized Service Center, please contact you
QSC dealer or contact QSC’s Technical Services Depart-
ment.
If the DSP-3 is returned to the factory for service, it should be sent
in the proper QSC carton. If you did not save the original carton, ask
your QSC dealer for one or call QSC to have one sent to you. This
warranty does not cover shipping damage caused by improper
packing or the use of improper shipping cartons.
FACSIMILE (FAX) NUMBERS:
WORLD WIDE WEB:
Sales & Marketing FAX
Technical Services FAX
ADDRESS:
(714) 754-6174
(714) 754-6173
TELEPHONE NUMBERS:
Main Number
(714) 754-6175
QSC Audio Products, Inc.
1675 MacArthur Boulevard
Sales Direct Line (714) 957-7100
or (800) 854-4079 toll free (U.S.A. only)
Costa Mesa, CA 92626-1468 USA
Technical Services (714) 957-7150
or (800) 772-2834 toll free (U.S.A. only)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1675 MacArthur Boulevard Costa Mesa, California 92626 USA PH: (714) 754-6175 FAX: (714) 754-6174
© Copyright 2001, QSC Audio Products, Inc.
QSC® is a registered trademark of QSC Audio Products, Inc., Costa Mesa, CA
“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office
Download from Www.Somanuals.com. All Manuals Search And Download.
|