Royal Consumer Information Products Outdoor Fireplace U19023 User Guide

0102 095 50281

SLIMLINE TURBO

(Flame System 5)

USERS INSTRUCTIONS

THIS CAT I_2HAPPLIANCE IS FOR USE

ON NATURAL GAS G20 AT A SUPPLY

PRESSURE OF 20 mbar IN GB & IE

HAND THESE INSTRUCTIONS TO THE USER

DESCRIPTION

Download from Www.Somanuals.com. All Manuals Search And Download.

Clearances

Side. Minimum clearance required to any combustible material to the side of the appliance must be 150mm.

Shelves. Minimum clearance to the underside of a 150mm deep combustible shelf from the hearth must be 790mm, add 12.5mm to this

dimension for every 25mm increase in the depth of the shelf.

To light the appliance

Press down the control button at the right top corner of the surround. The fan should be heard to start initially on high speed and then

reducing to low speed, a spark will be heard and the gas will light at the pilot positioned at the centre of the front simulated coal (if a

spark is not heard - check battery). Hold for a period of 10-15 seconds and release - the main burner will light.

A taper may light the appliance by placing the lit taper over the coal front at the approximate centre position and pressing the control

button. See Fig 1.

The thermoselector control situated behind the ashpan cover (fret) is to be set to a position which maintains the room at the desired

comfort level, i.e. the higher the control setting the higher the mean temperature of the room. Adjustments to this control will take time

for the effect in the room to be apparent.

To turn off the appliance and pilot - lift the control button.

IMPORTANT: After turning OFF or if the pilot and the appliance goes out for any reason, wait for three minutes before attempting to

relight.

Dismantling the Fire Bed for Cleaning

Allow the appliance to cool for 1 hour before handling any components.

Remove the loose coals, lift off the simulated coal front, and remove the coal support shelf. Once all the fibre components have been

removed from the firebed check that no debris has fallen in or lodged the burner slots. If any debris is present it may be easily removed

by using a small piece of thin cardboard to ease out any foreign matter. Be sure to remove the cardboard after use. Any sooty deposits or

debris left on the coals may be removed by using a soft brush or by careful use of a vacuum cleaner. . Cleaning should be carried out in

a well-ventilated area or in the open air, by gently brushing with the pieces held away from your face so that you avoid inhaling the

dust. We do not recommend the use of a normal domestic vacuum cleaner, which may blow dust back into the air. Any sooty deposit

on the thermocouple probe can be cleaned of using a non-fluffy cloth.

It is very important that the coals and the coal bed components are laid as shown no extra coals or material may be used. If any of the

items become lost or damaged, replacements must be obtained before further use of the appliance.

Relaying the Coal Bed

Fit the coal support shelf and simulated coal front. Fig 2

Referring to figures 2, 3 and 4 lay the coals as follows:

Place 4 large round coals between the simulated coal front and the support shelf. Fig 3

Place 3 round coals between the gaps in the front row. Fig 3

Place the 5 small round coals between the gaps formed in the coals laid in 1 & 2 above. Fig 4

Cleaning the Front of the Appliance

The fire must be turned off and allowed to cool. The paintwork should be cleaned with a soft cloth or soapy water; the brass trim has a

clear lacquer coating to preserve the polished finish. DO NOT USE ABRASIVES OR METAL POLISH.

-3-

Download from Www.Somanuals.com. All Manuals Search And Download.

Spares and Service

For spares and service contact your local supplier, installer or direct to the manufacturer stating that the appliance is a Slimline Turbo and

quote the serial number from the data label located on the fascia panel.

If the fire fails to light and no spark is heard - in the first instance a replacement battery should be obtained and fitted. To replace battery,

remove the heat shield protecting the unit and slide battery forward. Ensure -ve connection is uppermost on the replacement and slide

into the connector receptacles.

Advantage should be taken of regular servicing and inspection of gas appliances to ensure their continued safe operation.

Short Parts List

Description

Crosslee Pt No

Coal Support Shelves

Front Simulated Coal

Fibre Back

42836

42769

42830

42658

Set of Coals

9 volt Battery PP3S

REGISTRATION RECORD

Purchaser’s Name

and Address

........................................................ ............................................

.....................................................................................................

......................................................................................................

Supplier’s Name

and Address

Date of Purchase

.................................

Serial No .......................................

Please return these details with any components returned under guarantee.

Royal Cozyfires are manufactured by:

CROSSLEE plc

Aber Park Industrial Estate,

Aber Road, Flint, Flintshire. CH6 5EX

Spares Tel 01422 203963

Fax: 01422 204475

Service (GSA Ltd) 01703 516611

Customer Service 01422 200660

Fax 01422 206304

*Technical Help Line 0906 8633268

*Calls charged at 60p per minute

Download from Www.Somanuals.com. All Manuals Search And Download.

RCA CRT Television 27F671T User Guide
RCA Microcassette Recorder VR5340 User Guide
RCA TV VCR Combo T09082 User Guide
Roberts Radio MP3 Player Accessories 63I User Guide
Robic Fitness Electronics SC 606W User Guide
Samsung Home Theater System HT P38 User Guide
Sceptre Technologies Flat Panel Television E325BV HDU User Guide
Schneider Electric Welder Altivar 212 User Guide
Sears Humidifier 75814451 User Guide
SECO LARM USA Security Camera EV 1323C12DWQ User Guide