¨
Model No. 831.288221
Serial No
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
CAUTION
Read all precautions and
instructions in this manual
before using this equipment.
Keep this manual for future
reference.
USERÕS MANUAL
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new PROFORM¨ 928L
exercise cycle. The PROFORM 928L blends
advanced engineering with contemporary styling to
provide you with a low-impact workout in the conve-
nience and privacy of your own home.
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please mention the
product model number and serial number when call-
ing. The model number is 831.288221. The serial
number can be found on a decal attached to the
PROFORM¨ 928L (see the front cover of this manual
for the location of the decal).
For your benefit, read this manual carefully before
you use the PROFORM¨ 928L. If you have questions
after reading the manual, please call our toll-free
HELPLINE at 1-800-736-6879, Monday through
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Multi-position
Comfort
Handlebars
Console
Resistance Knob
Seat
Seat Post
Seat Pin
FRONT
Flywheel
Side Shield
Pedal
BACK
RIGHT SIDE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the
packing materials until assembly is completed. Assembly requires the included allen wrench
,
a phillips screwdriver
, and two adjustable wrenches
.
1. Hold one of the Stabilizers (5) against the Frame
(1), with the square holes facing away from the
Frame. Attach the Stabilizer with two M8 x 65mm
Carriage Bolts (38) and two M8 Nylon Locknuts
(39).
1
1
39
Attach the other Stabilizer (not shown) in the same
manner.
Square
Holes
39
5
38
24
2. Hold the Handlebar Post (2) near the Frame (1) as
shown. Connect the Extension Wire (37) to the
Reed Switch Wire (33). Next, carefully slide the
Handlebar Post down into the Frame. Be careful
not to pinch the Extension Wire or the Reed
Switch Wire. Secure the Handlebar Post with eight
M4 x 16mm Tapping Screws (30).
2
25
Slotted Tab
2
Next, press the Resistance Knob (25) onto the end
of the Resistance Cable (24). Slide the Resistance
Cable into the slotted tab on the Handlebar Post (2);
make sure that the Resistance Cable is turned
as shown. Firmly push down on the Resistance
Knob until the end of the Resistance Cable is fully
seated in the slotted tab.
37
30
33
30
1
30
4
3. Slide the bottom of the Left Handlebar (3) into the
Handlebar Post (2). Be sure that the holes in the
Handlebar and the Handlebar Post line up. Attach
the Handlebar with two M8 x 36mm Button Head
Bolts (14) and two M8 Nylon Locknuts (39).
3
39
Attach the Right Handlebar (4) in the same manner.
3
14
2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The Console (7) requires two "AA" batteries (not
included). Alkaline batteries are recommended.
Refer to the inset drawing. Remove the battery door
from the Console. Press two batteries into the bat-
tery compartment. Make sure that the negative
ends of the batteries (marked ÒÐÓ) are touching
the springs in the battery compartment. Reattach
the battery door.
4
7
37
Console
Plate
Console
Wire
Connect the console wire to the Extension Wire
(37).
Slide the Console (7) onto the console plate. Note:
The Console attaches by friction; it does not snap
into place.
Batteries
Battery Door
5. Insert the Seat Post (10) into the Frame (1). Press
the Frame Bushing (40) into the Frame. Align one of
the holes in the Seat Post with the hole in the
Frame. Insert the Seat Pin (35) through the Frame
and the Seat Post to select the desired seat height.
Make sure to insert the Seat Pin through one of
the holes in the Seat Post; do not insert the Seat
Pin under the Seat Post.
5
11
36
39
Next, attach the Seat (11) to the Seat Post (10) with
one M8 x 50mm Carriage Bolt (36) and one M8
Nylon Locknut (39).
10
40
35
1
6. Identify the Left Pedal (21). (The Left Pedal is
marked with an ÒL.Ó) Using an adjustable wrench,
tighten the Left Pedal counterclockwise into the left
arm of the Crank (20).
6
Tighten the Right Pedal (not shown) clockwise into
the Right arm on the Crank.
20
21
7. Make sure that all parts are properly tightened before you use the exercise cycle.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE EXERCISE CYCLE
HOW TO ADJUST THE SEAT
USING THE MULTI-POSITION HANDLEBARS
For effective
Your exercise
cycle features
padded, multiple-
position handle-
bars. They are
designed to offer
a maximum
amount of com-
fort while exer-
cising.
exercise, the
Seat (11) should
be at the proper
height. As you
pedal, there
should be a
slight bend in
your knees
when the pedals
are in the lowest
position. To
adjust the Seat,
first hold the
Seat and
11
10
1
DESCRIPTION OF THE CONSOLE
35
The console features
five modes that pro-
vide instant exercise
feedback during your
workouts. The modes
are described below.
Display
remove the Seat
Pin (35). Align one of the holes in the Seat Post (10)
with the hole in the Frame (1). Insert the Seat Pin into
the Frame and the Seat Post. Caution: Make sure to
insert the Seat Pin through one of the holes in the
Seat Post; do not insert the Seat Pin under the
Seat Post.
¥ SpeedÑDisplays
your pedaling
HOW TO ADJUST THE PEDALING RESISTANCE
Mode Indicators
speed, in miles per
hour.
To vary the
intensity of your
exercise, the
pedaling resis-
tance can be
adjusted. The
¥ TimeÑDisplays the
elapsed time. Note:
If you stop pedaling
for ten seconds or
longer, the time
25
resistance is
controlled with
mode will pause
until you resume.
the Resistance
Knob (25). To
increase the
¥ DistanceÑDisplays the total distance you have ped-
aled, in miles.
resistance, turn the Resistance Knob clockwise; to
decrease the resistance, turn the Resistance Knob
counterclockwise.
¥ CalorieÑDisplays the approximate number of calo-
ries you have burned.
BATTERY INSTALLATION
¥ ScanÑDisplays the speed, time, distance, and calo-
rie modes, for 5 seconds each, in a repeating cycle.
Before the console can be operated, two Ò"AA"Ó bat-
teries must be installed. If you have not installed bat-
teries, see assembly step 4 on page 5.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO OPERATE THE CONSOLE
Speed, time,
distance or
1. To turn on the power, press the on/reset button or
simply begin pedaling. When the power is turned
on, the entire display will appear for two seconds.
The console will then be ready for operation.
calorie modeÑ
To select one of
these modes for
continuous dis-
play, press the
mode button
2. Select one of the five modes:
repeatedly. The
mode indicators
will show which mode is selected. Make sure that
the scan mode is not selected.
Scan modeÑ
When the power
is turned on, the
scan mode will
automatically be
selected. One
3. To reset the display, press the on/reset button.
mode indicator
will show that
the scan mode
is selected, and
a flashing mode indicator will show which mode is
currently displayed. Note: If a different mode is
selected, you can select the scan mode again by
repeatedly pressing the mode button.
4. To turn off the power, simply wait for about four min-
utes. Note: The console has an Òauto-offÓ fea-
ture. If the pedals are not moved and the con-
sole buttons are not pressed for four minutes,
the power will turn off automatically in order to
conserve the batteries.
STORAGE AND TROUBLE-SHOOTING
Inspect and tighten all parts of the exercise cycle reg-
ularly. Replace any worn parts immediately.
HOW TO TIGHTEN THE CRANK
If the arms of
the Crank (20)
become loose,
they should be
tightened in
order to prevent
excessive wear.
Loosen the
The exercise cycle can be cleaned with a soft, damp
cloth. Avoid spilling liquid on the console. Keep the
console out of direct sunlight or the display may be
damaged. Remove the batteries when storing the
exercise cycle.
Slotted
Crank
Nut
Crank
Nut
BATTERY REPLACEMENT
crank nut on
the left arm of
the Crank.
Place the end
of a standard
If the console does not function properly, the batteries
should be replaced. See assembly step 4 on page 5.
In addition, make sure that the console wire is con-
nected to the reed switch wire.
20
screwdriver in one of the slots in the slotted crank nut.
Lightly tap the screwdriver with a hammer to turn the
slotted crank nut counterclockwise until the arms are
no longer loose. Do not overtighten the slotted
crank nut. When the slotted crank nut is properly
tightened, retighten the Crank Nut.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST THE REED SWITCH
end of the Resistance Strap (17) and pull it back
slightly to remove any slack. While holding the end of
the Resistance Strap, fully close the Strap Buckle.
Turn the crank for a moment to make sure that there
is not too much resistance.
If the console does not display correct feedback, the
reed switch should be adjusted. In order to adjust the
reed switch, the Left Side Shield (12) must be remov-
ed. Remove the four Side Shield Screws (15) from the
Right Side Shield (13) and the three M4 x 16mm
Tapping Screws (30) from the bottom of the Left Side
Shield. Carefully slide the Left Side Shield forward off
the arm of the Crank (20) and remove it.
HOW TO ADJUST THE DRIVE BELT
The exercise cycle features a drive belt that must be
kept properly adjusted. If the belt causes excessive
noise or slips as you pedal, the belt should be
checked. To do this, the side shields must first be
removed. Refer to the instructions on this page and
remove the left side shield. Next, remove the right
side shield the same way.
15
13
Press down on
the center of the
23
15
Drive Belt (23)
between the front
and rear pulleys.
There should be
from 1/4Ó to 1/2Ó
of movement in
the center of the
Belt.
20
12
30
30
Next, locate the
Reed Switch (33).
46
Turn the crank until
the Magnet (46) is
aligned with the
Reed Switch.
Loosen but do not
remove the M4 x
16mm Screw (30).
Slide the Reed
If the drive belt is
properly adjust-
ed, reattach the
side shields. If
the Belt needs to
be adjusted,
loosen the Axle
Nut (29) on each
side of the fly-
Side View
30
33
27
Switch slightly clos-
er to or away from the Magnet. Retighten the Screw.
Turn the crank for a moment. Repeat until the console
displays correct feedback. When the Reed Switch is
correctly adjusted, reattach the left side shield.
29
wheel. To tighten
the Belt, turn the
Adjustment Nuts
(27) clockwise; to loosen the Belt, turn the Adjustment
Nuts counterclockwise. Make sure that the Flywheel is
straight and tighten the Axle Nuts (29). Reattach the
side shields.
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedaling resistance when the
resistance knob is turned to the highest setting, the
Resistance Strap (17) may need to be adjusted.
To adjust the Resistance Strap, first turn the resis-
tance knob
to the low-
est setting.
Next, locate
and open
the Strap
Buckle (18)
on the
underside
of the side
shields.
Grip the
17
18
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
WARNING: Before beginning this or any exer-
cise program, consult your physician. This is
especially important for persons over the age
of 35 or persons with pre-existing health
problems.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, first exer-
cise for at least four
minutes. Then, stop
exercising and place
two fingers on your
wrist as shown. Take
a six-second heart-
beat count, and mul-
tiply the result by 10
to find your heart
rate. For example, if your six-second heartbeat count
is 14, your heart rate is 140 beats per minute. (A six-
second count is used because your heart rate will
drop rapidly when you stop exercising.)
To find the proper heart rate for you, first find your age
on the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers are your Òtraining
zone.Ó The lowest number is the recommended heart
rate for fat burning; the middle number is the heart
rate for maximum fat burning; the highest number is
the heart rate for aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretch-
ing and light exercise. A proper warm-up increases
your body temperature, heart rate, and circulation in
preparation for exercise.
Burning Fat
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise pro-
gram, do not keep your heart rate in your training
zone for longer than 20 minutes.)
To burn fat effectively, you must exercise at a rela-
tively low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired. Caution: Be sure to progress at your own
pace and avoid overdoing it. Incorrect or excessive
training may result in injury to your health.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three work-
outs each week, with at least one day of rest between
Remember, the key to success is make exercise a
regular and enjoyable part of your everyday life.
PART LISTÑModel No. 831.288221
R0499A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
2
4
1
2
2
1
1
1
1
2
4
1
1
1
1
1
1
1
1
1
1
Frame
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
#
1
2
2
2
18
1
2
1
1
1
1
1
4
7
3
3
1
4
1
1
1
2
1
1
Flywheel Axle
Adjustment Nut
Adjustment Bolt
Axle Nut
M4 x 16mm Tapping Screw
Flat Head Screw
Handlebar Endcap
Reed Switch/Wire
Reed Switch Clip
Seat Pin
M8 x 50mm Carriage Bolt
Extension Cable
M8 x 65mm Carriage Bolt
M8 Nylon Locknut
Frame Bushing
Post Endcap
M4 x 14mm Bolt
M4 Washer
Spring
Handlebar Post
Left Handlebar
Right Handlebar
Stabilizer
Stabilizer Endcap
Console
Foam Armrest
Foam Grip
Seat Post
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Seat
Left Side Shield
Right Side Shield
M8 x 36mm Button Head Bolt
Side Shield Screw
Flywheel
Resistance Strap
Strap Buckle
Crank Hardware Assembly
Crank/Pulley
Left Pedal
M4 Nut
Magnet
M10 Washer
UserÕs Manual
Allen Wrench
Right Pedal
Drive Belt
Resistance Cable
Resistance Knob
#
Note: Ò#Ó refers to a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. 831.288221
R0499A
15
32
4
7
25
15
39
24
39
13
3
30
14
12
2
8
30
45
43
42
30
41
11
9
44
41
39
37
36
27
28
40
16
29
47
10
26
30
30
17
20
30
35
27
41
40
22
30
28
47
29
30
33
6
34
39
19
46
38
1
23
39
19
39
5
18
20
31
6
39
6
21
5
6
38
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The model number and serial number of your PROFORM¨ 928L
are listed on a decal attached to the frame. See the front cover of
this manual to find the location of the decal.
Model No. 831.288221
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
QUESTIONS?
If you find that:
¥ you need help assembling or
operating the PROFORM¨ 928L
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
¥ a part is missing
¥ or you need to schedule repair
service
¥ The MODEL NUMBER of the product (831.288221).
¥ The NAME of the product (PROFORM¨ 928L).
call our toll-free HELPLINE
¥ The KEY NUMBER and DESCRIPTION of the PART (see the
PART LIST and the EXPLODED DRAWING on pages 10 and 11).
1-800-736-6879
MondayÐSaturday, 7 amÐ7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART
(1-800-366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS BIKE EXERCISER, contact the nearest SEARS Service Center throughout the United States
and SEARS will repair or replace the BIKE EXERCISER, free of charge.
This warranty does not apply when the BIKE EXERCISER is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 154919 R0499A
Printed in China © 1999 Sears, Roebuck, and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|