Poulan Trimmer 545186849 User Manual

R
Please do not return unit to retailer.  
Por favor, no devuelva el aparato al lugar de compra.  
Veuillez ne pas retourner l’outil au détaillant.  
1-800-554-6723  
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
PP25E  
For Occasional Use Only  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en le-  
siones graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le  
faire pourrait entraîner des blessures graves.  
Poulan PRO  
1030 Stevens Creek Road  
Augusta, GA 30907  
Poulan PRO  
850 Matheson Blvd. West  
Mississauga, Ontario L5V 0B4  
545186849 Rev. 3 3/1/09 BRW  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IDENTIFICATION OF SAFETY SYMBOLS  
Secure hair above shoulder length. Do  
not wear jewelry, loose clothing, or  
clothing with loosely hanging straps,  
ties, tassels, etc. They can be caught in  
moving parts.  
Assist handle to be positioned only below  
the arrow.  
Never allow children to operate this unit.  
Store unit indoors in a high, dry place out of the reach of  
children.  
When servicing unit, use only identical replacement  
parts.  
Always stop unit and disconnect spark plug before clean-  
ing or servicing.  
WARNING: Fire hazard. Never mix, pour, or store gasoline or  
use the unit near a flame or sparks (including smoking, open flames, or  
work that can cause sparks).  
Use unleaded gasoline and two--stroke oil mixed at a ratio of  
40:1 (2.5%).  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONAL ATTACHMENTS  
These attachments used in combination with the specified powerhead have been evaluated  
to ANSI B175.3--2003, “Grass Trimmers and Brushcutters -- Safety Requirements”. These  
combinations have been evaluated by Underwriter’s Laboratories Inc. (UL) and are conse-  
quently UL listed:  
Cutting attachment / guard,  
part. no.  
Powerhead model Attachments  
Type  
Trimmer head  
PP25E  
TNG 7  
537419214 / 545071802  
952711610  
Brushcutter attachment PP4000C  
These attachments used in combination with the specified powerhead have been evaluated  
to applicable ISO-- and EN safety requirement standards by the Swedish Machinery Testing  
Institute:  
Attachments  
Type  
Part. no.  
Edger attachment  
Cultivator attachment  
Blower attachment  
Pruner attachment  
Pruner attachment  
PP1000E  
PP2000T  
PP3000B  
PP5000P  
PP5500P  
952711607  
952711608  
952711609  
952711612  
952711672  
SAFETY RULES  
your unit (safety glasses are available).  
Eye protection should be marked Z87.  
S Always wear face or dust mask if operation  
is dusty.  
WARNING: When using gardening  
appliances, basic safety precautions must al-  
ways be followed to reduce the risk of fire and  
serious injury. Read and follow all instructions.  
This power unit can be dangerous! Operator is  
responsible for following instructions and warn-  
ings on unit and in manual. Read entire instruc-  
tion manual before using unit! Be thoroughly fa-  
miliar with the controls and the proper use of the  
unit. Restrict the use of this unit to persons who  
have read, understand, and will follow the  
instructions and warnings on the unit and in the  
manual. Never allow children to operate this  
unit.  
S Always wear heavy, long pants, long  
sleeves, boots, and gloves. Wearingsafety  
leg guards is recommended.  
S Always wear foot protection. Do not go  
barefoot or wear sandals. Stay clear of  
spinning line.  
S Secure hair above shoulder length. Secure  
or remove loose clothing or clothing with  
loosely hanging ties, straps, tassels, etc.  
They can be caught in moving parts.  
S Being fully covered also helps protect you  
from debris and pieces of toxic plants  
thrown by spinning line.  
S Stay Alert. Do not operate this unit when you  
are tired, ill, upset or under the influence of al-  
cohol, drugs, or medication. Watch what you  
are doing; use common sense.  
INSTRUCTION  
MANUAL  
SAFETY INFORMATION  
ON THE UNIT  
S Wear hearing protection.  
S Never start or run inside a closed room or  
building. Breathing exhaust fumes can kill.  
S Keep handles free of oil and fuel.  
S Always keep engine on the right hand side  
of your body.  
S Hold the unit firmly with both hands.  
S Keep cutting attachment below waist level  
and away from all parts of your body. Do  
not raise engine above your waist.  
S Keep all parts of your body away from muf-  
fler and spinning line (or other optional at-  
tachment). A hot muffler can cause serious  
burns.  
DANGER: Never use blades withline  
trimmer attachment. Never use flailing de-  
vices with any attachment. This unit (when  
used withsupplied linetrimmer attachment) is  
designed for line trimmer use only. Use of any  
other accessories with line trimmer attach-  
ment will increase the risk of injury.  
If situations occur which are not covered in  
this manual, use care and good judgment. If  
you needassistance, contact your authorized  
service dealer or call 1-800-554-6723.  
OPERATOR SAFETY  
S Keep firm footing and balance. Do not over-  
reach or use from unstable surfaces such as  
ladders, trees, steep slopes, rooftops, etc.  
S Use only in daylight or good artificial light.  
S Dress properly. Always wear safety  
glasses or similar eye protection when op-  
erating, or performing maintenance, on  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Use only for jobs explained in this manual  
(or manuals for optional attachments).  
S Keep others including children, animals, by-  
standers, and helpers at least 50 feet (15 me-  
ters) away. Stop the unit immediately if you  
are approached.  
material fromthecutting blade. Do not grab or  
hold attachment by the cutting blade.  
WARNING: Inspect the area to be  
edged before each use. Remove objects  
(rocks, broken glass, nails, wire, string, etc.)  
which can be thrown by the blade or can wrap  
around the shaft.  
LINE TRIMMER SAFETY  
WARNING: Inspect the area to be  
trimmed before each use. Remove objects  
(rocks, broken glass, nails, wire, etc.) which  
can be thrown by or become entangled in line.  
Hard objects can damage the trimmer head  
and be thrown causing serious injury.  
WARNING: Disconnect the spark  
plug before performing maintenance except  
carburetor adjustments.  
S Inspect entire unit before each use. Replace  
damaged parts. Check for fuel leaks. Make  
sure all fasteners are in place and securely  
fastened.Maintain unit according to recom-  
mended procedures.  
S Have all maintenance and service not ex-  
plained in this manual performed by an au-  
thorized service dealer.  
S Throw away blades that are bent, warped,  
cracked, broken, or damaged in any other  
way. Replace parts that are cracked, chipped,  
or damaged before using the unit.  
S Use only recommended Poulan PRO parts  
and accessories. Never use wire, wire  
rope, string, flailing devices, etc.  
S Be sure blade stops turning when engine  
idles (see CARBURETOR ADJUST-  
MENTS section of powerhead manual).  
S Remove the blade before making carburetor  
adjustments. Hold the unit by hand. Do not  
make carburetor adjustments from the blade  
side of the unit.  
S Keep others away when making carburetor  
adjustments.  
S Never start the unit with the clutch housing re-  
moved. The clutch can fly off and cause seri-  
ous injury.  
S If blade strikes a foreign object, follow these  
steps: stop unit and disconnect spark plug  
wire (or disconnect from power source), in-  
spect for damage, and repair any damage be-  
fore resuming operation of the unit.  
WARNING: Disconnect the spark  
plug before performing maintenance except  
carburetor adjustments.  
S Keep others including children, animals, by-  
standers, and helpers at least 50 feet (15 me-  
ters) away. Bystanders should be encour-  
aged to wear safety glasses. Stop engine  
immediately if you are approached.  
S Use only for trimming, scalping, mowing and  
sweeping. Do not use for edging, pruning or  
hedge trimming.  
S Cut from your right to your left. Cutting on  
left side of the shield will throw debris away  
from the operator.  
S Look for and replace damaged or loose  
parts before each use. Look for and repair  
fuel leaks before use. Keepin good working  
condition.  
S Have all maintenance and service not ex-  
plained in this manual performed by an au-  
thorized service dealer.  
S Replace trimmer head parts that are  
chipped, cracked, broken, or damaged in  
any other way before using the unit.  
S Maintain unit according to recommended  
procedures. Keep cutting line at proper  
length.  
S Use only 0.080(2 mm) diameter Poulan  
PRO brand line. Never use wire, rope, string,  
etc.  
S Never direct discharge of material toward  
bystanders nor allow anyone near the area  
of operation. Use care in directing dis-  
charge to avoid glass enclosures, automo-  
biles, and the like.  
S Install required shield properly before using  
the unit. Use only specified trimmer head;  
make sure it is properly installed and se-  
curely fastened.  
S Always keep the wheel in contact with the  
ground.  
S Make sure unit is assembled correctly as  
shown in this manual.  
S Keep all parts of your body away from the  
blade and muffler.  
S Make carburetor adjustments with lower  
end supported to prevent line from contact-  
ing any object.  
S Always push the unit slowly over the ground.  
Stay alert for uneven sidewalks, holes in the  
terrain, large roots, etc.  
S Keep others away when making carburetor  
adjustments.  
S Do not force the unit. Use only for jobs ex-  
plained in this manual. Use only for edging.  
Do not abuse unit. Do not use in rain or wet  
locations.  
S Use only recommended Poulan PRO ac-  
cessories and replacement parts.  
EDGER SAFETY  
S To reduce the risk of fire, do not allow exces-  
sive grass, leaves, or grease to accumulate  
on the attachment.  
S Objects struck by the cutting member can  
cause serious injuries to persons. The lawn  
should always be carefully examined and  
cleared of all objects prior to edging.  
S Never operate without blade shield in place  
and in good working order.  
WARNING: RISK OF CUT. KEEP  
HANDS AND FEET AWAY FROM BLADE  
AND CUTTING AREA. Do not attempt to  
clear away cut material or hold material to be  
cut when the blade is in motion. Make sure  
powerhead is stopped and spark plug wire is  
disconnected (or powerhead is disconnected  
from power source) when removing jammed  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Make sure unit is assembled correctly as  
shown in this manual.  
homeowner use, the muffler and spark arrest-  
ing screen will not require any service. After  
50 hours of use, we recommend that your  
muffler be serviced or replaced by an autho-  
rized service dealer.  
S Use only recommended Poulan PRO ac-  
cessories and replacement parts.  
FUEL SAFETY  
S Mix and pour fuel outdoors.  
S Keep away from sparks or flames.  
S Use a container approved for fuel.  
S Do not smoke or allow smoking near fuel or  
the unit.  
ADDITIONAL SAFETY RULES  
FOR OPTIONAL ATTACHMENTS  
WARNING: For each optional attach-  
ment used, read entire instruction manual be-  
fore use and follow all warnings and instructions  
in manual and on attachment.  
S Avoid spilling fuel or oil. Wipe up all fuel  
spills.  
S Move at least 10 feet (3 meters) away from  
fueling site before starting engine.  
S Stop engine and allow to cool before re-  
moving fuel cap.  
WARNING: Ensure handlebar is  
installed when using brushcutter attachment.  
Attach handlebar above arrow on safety label  
on the upper shaft (engine end of unit). If your  
brushcutter attachment does not include a  
S Always store gasoline in a container ap-  
proved for flammable liquids.  
TRANSPORTING AND STORAGE  
S Do not grasp or hold exposed blade.  
S Stop powerhead before leaving work area.  
S Allow engine to cool before storing or trans-  
porting in vehicle.  
S Empty the fuel tank before storing or trans-  
porting the unit. Use up fuel left in thecarbu-  
retor by starting the engine and letting it run  
until it stops.  
handlebar,  
a
handlebar accessory kit  
(#530071451) is available from your autho-  
rized service dealer.  
S Store unit and fuel in area where fuel vapors  
cannot reach sparks or open flames from wa-  
ter heaters, electric motors or switches, fur-  
naces, etc.  
S Store unit so blade cannot accidentally cause  
injury. The unit can be hung by the shaft.  
S Store unit out of reach of children.  
BLOWER/VACUUM SAFETY  
WARNING: Inspect area before  
starting unit. Remove all debris and hard ob-  
jects such as rocks, glass, wire, etc. that can  
ricochet, be thrown, or otherwise cause injury  
or damage during operation.  
S Do not set unit on any surface except a  
clean, hard area while engine is running.  
Debris such as gravel, sand, dust, grass,  
etc., could be picked up by the air intake  
and thrown out through discharge opening,  
damaging unit, property, or causing serious  
injury to bystanders or operator.  
S Never place objects inside the blower  
tubes, vacuum tubes or blower outlet. Al-  
ways direct the blowing debris away from  
people, animals, glass, and solid objects  
such as trees, automobiles, walls, etc. The  
forceof air can causerocks, dirt, or sticks to  
be thrown or to ricochet which can hurt  
people or animals, break glass, or cause  
other damage.  
S Never run unit without the proper equip-  
ment attached. When using your unit as a  
blower, always install blower tubes.  
S Check air intake opening, blower tubes or  
vacuum tubes frequently, always with en-  
gine stopped and spark plug disconnected.  
Keep vents and discharge tubes free of de-  
bris which can accumulate and restrict  
proper air flow.  
S Never place any object inair intake opening  
as this could restrict proper air flow and  
cause damage to the unit.  
S Never use for spreading chemicals, fertiliz-  
ers, or other substances which may contain  
toxic materials.  
WARNING: The engine exhaust  
from this product contains chemicals known  
totheStateof California tocause cancer, birth  
defects or other reproductive harm.  
SAFETY NOTICE: Exposure to vibrations  
through prolonged use of gasoline powered  
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or abnor-  
mal swellings. Prolonged use in cold weather  
has been linked to blood vessel damage in  
otherwise healthy people. If symptoms occur  
such as numbness, pain, loss of strength,  
change in skin color or texture, or loss of feeling  
in the fingers, hands, or joints, discontinue the  
use of this tool and seek medical attention. An  
anti--vibration system does not guarantee the  
avoidance of these problems. Users who oper-  
ate power tools on a continual and regular basis  
must monitor closely their physical condition  
and the condition of this tool.  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442 and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equippedwith aspark arresting screen. If you  
operate ina locale wheresuch regulations ex-  
ist, you are legally responsible for maintaining  
the operating condition of theseparts. Failure  
to do so is a violation of the law. For normal  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
S To avoid spreading fire, do not use near leaf  
or brush fires, fireplaces, barbecue pits,  
ashtrays, etc.  
Proboscis  
nose  
BRUSHCUTTER SAFETY  
DANGER: Blade can thrust violently  
away from material it does not cut. Blade  
thrust can cause amputation of arms or legs.  
S Useonly specified blade and make sure it is  
properly installed and securely fastened.  
S Cut from your left to your right. Cutting on  
the right side of the shield will throw debris  
away from the operator.  
S Always use the handlebar and a properly  
adjustedshoulder strap withblade (seeAS-  
SEMBLY instructions in brushcutter attach-  
ment instruction manual).  
CULTIVATOR SAFETY  
WARNING: Rotating tines can cause  
serious injury. Keep away from rotating tines.  
Stop the engine and disconnect the spark plug  
before unclogging tines or making repairs.  
WARNING: Do not use trimmer head  
as a fastening device for the blade.  
WARNING: The blade continues to  
spin after the trigger is released or engine is  
turned off. The coasting blade can throw ob-  
jects or seriously cut you if accidentally  
touched. Stop the blade by contacting the  
right hand side of the coasting blade with ma-  
terial already cut.  
WARNING: Inspect the area to be  
cultivated before starting the unit. Remove all  
debris and hard and sharp objects such as  
rocks, vines, branches, rope, string, etc.  
S Avoid heavy contact with solid objects that  
might stop the tines. If heavy contact oc-  
curs, stop the engine and inspect the unit  
for damage.  
S Never operate the cultivator without thetine  
cover in place and properly secured.  
S Keep the tines and guard clear of debris.  
S After striking a foreign object, stop the en-  
gine, disconnect the spark plug and inspect  
the cultivator for damage. Repair before re-  
starting.  
S Disconnect attachment from the drive en-  
gine before cleaning the tines with a hose  
and water to remove any build--up. Oil the  
tines to prevent rust.  
S Always wear gloves when servicing or  
cleaning the tines. The tines become very  
sharp from use.  
WARNING: Inspect the area to be  
cut before each use. Remove objects (rocks,  
broken glass, nails, wire, etc.) which can be  
thrown or become entangled in the blade or  
trimmer line.  
S Do not run unit at high speed unless culti-  
vating.  
HEDGE TRIMMER SAFETY  
S Throw away and replace blades that are  
bent, warped, cracked, broken or damaged  
in any other way.  
DANGER: RISK OF CUT; KEEP  
HANDS AWAY FROM BLADE -- Blade moves  
momentarily after the trigger is released or en-  
gine is turned off. Do not attempt to clear away  
cut material when the blade is in motion. Make  
sure engine is turned off, the spark plug wire is  
disconnected, and the blade has stopped mov-  
ing before removing jammed material from the  
cutting blade. Do not grab or hold the unit by the  
cutting blade.  
S Install required shield properly before using  
the unit. Use the metal shield for all metal  
blade use.  
WARNING: Only use brushcutter at-  
tachments that provide a metal shield with  
proboscis nose.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING: To prevent serious inju-  
ry, do not use more than one boom extension  
with a pole pruner attachment.  
WARNING: Keep the pruner away  
from power lines or electrical wires.  
S Only use for pruning limbs or branches up  
to 6 inches (15 cm) in diameter.  
WARNING: Inspect the area before  
starting the unit. Remove all debris and hard  
objects such as rocks, glass, wire, etc. that  
can ricochet, be thrown, or otherwise cause  
injury or damage during operation.  
S Do not operate the unit faster than the  
speed needed to prune. Do not run the unit  
at high speed when not pruning.  
S Do not use a cutting blade that is bent,  
warped, cracked, broken or damaged in any  
other way. Have worn or damaged parts re-  
placed by your authorized service dealer.  
S Always keep unit in front of your body.  
Keep all parts of your body away from the  
cutting blade.  
S Always stop the unit when work is delayed  
or when walking from one cutting locationto  
another.  
S If you strike or become entangled with afor-  
eign object, stop the engine immediately  
and check for damage. Have any damage  
repaired by an authorized service dealer  
before attempting further operations. Dis-  
card blades that are bent, warped, cracked  
or broken.  
S Keep the cutting bladeand air vents clear of  
debris.  
POLE PRUNER SAFETY  
S Stop the unit immediately if you feel exces-  
sive vibration. Vibration is a sign of trouble.  
Inspect thoroughly for loose nuts, bolts or  
damage before continuing. Contact an au-  
thorized service dealer for repair or re-  
placement of affected parts as necessary.  
WARNING: The reciprocating blade/  
rotating chain can cause severe injury. In-  
spect the unit before use. Do not operate unit  
with a bent, cracked or dull blade or dull chain.  
Keep away from the blade/chain.  
SNOW THROWER SAFETY  
WARNING: The reciprocating blade/  
rotating chain is sharp. Do not touch. To pre-  
vent serious injury, always stop engine and  
ensure blade/chain has stopped moving, dis-  
connect spark plug, and wear gloves when  
changing or handling the blade or chain.  
WARNING: Keep hands and feet  
away from the rotor when starting or running  
the engine. Never attempt to clear the rotor  
with the engine/motor running. Stop engine  
and disconnect spark plug before unclogging  
snow or debris from discharge chute or when  
adjusting vanes.  
WARNING: A coasting blade/rotat-  
ing chaincancauseinjury while it continues to  
move after the engine is stopped. Maintain  
proper control of the unit until the blade/chain  
has completely stopped moving. Keep  
hands, face and feet at a distance from all  
moving parts. Do not attempt to touch or stop  
the blade or chain when it is moving.  
WARNING: Never lean over dis-  
charge chute. Rocks or debris could be  
thrown into the eyes and face and cause seri-  
ous injury or blindness.  
WARNING: Inspect the area where  
the unit is to be used. Remove objects that  
could be thrown or damage the unit. Some  
objects may be hidden by fallen snow -- be  
alert for the possibility.  
S Direct material discharge away from glass  
enclosures, automobiles, etc.  
WARNING:  
Falling objects can  
cause severe head injury. Wear head protec-  
tion when operating this unit with a pole prun-  
er attachment.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Do not run engine at high speed while not  
removing snow.  
S Never operate the snowthrower near glass  
enclosures, automobiles and trucks.  
S Never attempt to use the snowthrower on a  
roof.  
S Be attentive when using the snowthrower,  
and stay alert for holes in the terrain and  
other hidden hazards.  
S Never operate the snowthrower near win-  
dow wells, dropoffs, etc.  
S Make sure the rotor will spin freely before  
attaching the snowthrower to the power-  
head.  
S If the rotor will not rotate freely due to frozen  
ice, thaw the unit before thoroughly before  
attempting to operate under power.  
S Keep the rotor clear of debris.  
S Do not throw snow near other people. The  
snow thrower could propel small objects at  
high speed causing injury.  
S After striking a foreign object, stop the en-  
gine, disconnect spark plug and inspect the  
snowthrower for damage and repair if nec-  
essary before restarting unit.  
S Never discharge snow onto public roads or  
near moving traffic.  
S Clear snow from slopes by going up and  
down; never across. Use caution when  
changing directions. Never clear snow from  
steep slopes.  
S Let snowthrower run for a few minutes after  
clearing snow so moving parts do not  
freeze.  
S Look behind and use care when backing  
up. Exercise caution to avoidslipping or fal-  
ling, especially when operating in reverse.  
S Know how to stop quickly.  
ASSEMBLY  
WARNING: If received assembled,  
repeat all steps to ensure your unit is properly  
assembled and all fasteners are secure.  
Coupler  
Primary Hole  
Guide Recess  
Examine parts for damage. Do not use dam-  
aged parts.  
NOTE: If you need assistance or find parts  
missing or damaged, call 1-800-554-6723.  
Locking/  
Release  
Button  
Upper  
Shaft  
Attachment  
It is normal for the fuel filter to rattle in the  
empty fuel tank.  
Finding fuel or oil residue on muffler is normal  
due to carburetor adjustments and testing  
done by the manufacturer.  
WARNING: Make sure the locking/  
release button is locked in the primary hole  
and the knob is securely tightened before op-  
erating the unit. All attachments are designed  
to be used in the primary hole unless otherwise  
stated in the applicable attachment instruction  
manual. Using the wrong hole could lead to seri-  
ous injury or damage to the unit.  
INSTALLING TRIMMER OR EDGER  
ATTACHMENTS  
CAUTION: When removing or installing at-  
tachments, place the unit on a flat surface for  
stability.  
1. Loosen the coupler by turning the knob  
counterclockwise.  
Coupr  
LOOSEN  
Shipping  
protector  
Locking/Release  
Button in Primary Hole  
Knob  
TIGHTEN  
For assembly of optional attachments (see  
list on page 12), refer to the ASSEMBLY sec-  
tion of the applicable attachment instruction  
manual.  
2. Remove shipping protector from coupler.  
3. Remove the shaft cap from the trimmer  
attachment (if present).  
ADJUSTING THE ASSIST HANDLE  
4. Position locking/release button of attach-  
ment into guide recess of coupler.  
5. Push the attachment into the coupler until  
the locking/release button snaps into the  
primary hole.  
WARNING: When adjusting the assist  
handle, be sure it remains above the safety label  
and below the mark or arrow on the shaft.  
1. Loosen wing nut on handle.  
2. Rotate the handle on the shaft to an up-  
right position; retighten wing nut.  
6. Before using theunit, tighten the knobse-  
curely by turning clockwise.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
ATTACHING SHIELD (FOR LINE  
TRIMMER ATTACHMENT)  
Slot  
Shield  
WARNING: The shield must be prop-  
erly installed. The shield provides partial protec-  
tion from the risk of thrown objects to the opera-  
tor and others and is equipped with a line limiter  
blade which cuts excess line to the proper  
length. The line limiter blade (on underside of  
shield) is sharp and can cut you. For proper  
orientation of shield, see KNOW YOUR TRIM-  
MER illustration in OPERATION section.  
1. Remove wing nut from shield.  
Bracket  
Wing  
Nut  
Line Limiter Blade  
2. Insert bracket into slot as shown.  
3. Pivot shield until bolt passes throughhole  
in bracket.  
4. Securely tighten wing nut onto bolt.  
OPERATION  
KNOW YOUR TRIMMER  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.  
Compare the illustrations with your unit to familiarize yourself with the location of the various controls  
and adjustments. Save this manual for future reference.  
Attachment hanger  
Muffler  
Assist Handle  
Trimmer  
Attachment  
ft  
Throttle  
Trigger  
Tri
He
Depth  
Adjustment  
Knob  
Spark  
Plug  
Primer  
Bulb  
Blade  
Shield  
Edger  
Attachment  
Start  
Lever  
ON/STOP  
Switch  
Gearbox  
Wheel  
Starter handle  
Edger  
Blade  
ON/STOP SWITCH  
START LEVER  
The ON/STOP switch is located on the trigger  
handle and is used to stop the engine. To stop  
the engine, push and release the engine ON/  
STOP switch.  
The START LEVER helps to supply fuel to the  
engine to aid in starting. Activate the starting  
system by moving the start lever to the START  
position. DO NOT squeeze the throttle trigger  
until the engine has started and runs. After the  
engine starts, allow the engine to warm--up  
10--15 seconds, then fully squeeze the throttle  
trigger to deactivate the starting system.  
PRIMER BULB  
The PRIMER BULB removes air from thecar-  
buretor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate the primer  
bulb by pressing it and allowing it to return to  
its original form.  
COUPLER  
The COUPLER enables optional attach-  
ments to be installed on the unit.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRIMMER HEAD  
DEPTH ADJUSTMENT KNOB  
The DEPTH ADJUSTMENT KNOB is used  
to adjust the wheel for blade cutting depth  
when edging.  
The TRIMMER HEAD holds the cutting line  
and rotates during operation. It is designed to  
cut grass.  
BLADE  
The BLADE is designed to cut sod.  
BEFORE STARTING ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you begin.  
If you do not understand the safety rules, do not  
attempt to fuel your unit. Call 1-800-554-6723.  
FUELING ENGINE  
HOW TO START YOUR UNIT  
WARNING: Remove fuel cap slowly  
when refueling.  
WARNING: Avoid any contact with  
the muffler. A hot muffler can cause serious  
burns.  
HELPFUL TIP  
To obtain the correct oil mix  
ratio, pour 3.2 ounces of  
2-cycle synthetic oil into  
one gallon of fresh gas.  
Starting position  
This engine is certified to operate on unleaded  
gasoline. Before operation, gasoline must be  
mixed with a good quality synthetic 2-cycle  
air-cooled engine oil designed to be mixed at a  
ratio of 40:1. Poulan/WEED EATER brand  
synthetic oil is recommended. Mix gasoline and  
oil at a ratio of 40:1. A 40:1 ratio is obtained by  
mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon  
(4 liters) of unleaded gasoline. DO NOT USE  
automotive oil or marine oil. These oils will  
cause engine damage. When mixing fuel, follow  
instructions printed on container. Once oil is  
added to gasoline, shake container momentarily  
to assure that the fuel is thoroughly mixed.  
Always read and follow the safety rules relating  
to fuel before fueling your unit.  
HELPFUL TIP  
If your engine still does not  
start after following these  
instructions, please call  
1 -800 -554-6723.  
STARTING A COLD ENGINE  
NOTE: DO NOT squeeze the throttle trigger  
until the engine has started and runs.  
1. Set unit on a flat surface.  
2. Slowly press the primer bulb 6 times.  
3. Move the start lever to the START posi-  
tion.  
CAUTION: Never use straight gasoline in  
your unit. This will cause permanent engine  
damage and void the limited warranty.  
FUEL REQUIREMENTS  
Primer Bulb  
This engine requires the use of minimum 87  
octane [R+M]/2 clean gasoline.  
IMPORTANT  
Use of alcohol blended fuels (called gasohol or  
using ethanol or methanol) can cause major en-  
gine performance and durability problems.  
WARNING: Alternative fuels (not gas-  
oline) such as E--15 (15% alcohol), E--20 (20%  
alcohol), E--85 (85% alcohol) are NOT classified  
as gasoline and are NOT approved for use in  
2--stroke gasoline engines. Use of alternative  
fuels will cause problems such as: improper  
clutch engagements, overheating, vapor lock,  
power loss, lubrication deficiency, deterioration  
of fuel lines, gaskets and internal carburetor  
components, etc. Alternative fuels cause high  
moisture absorption into the fuel/oil mixture  
leading to oil and fuel separation.  
Start Lever  
HOW TO STOP YOUR UNIT  
S Release the throttle trigger.  
S Push and release the engine ON/STOP  
switch. The switch will automatically return to  
the ON position. Wait 5 seconds before at-  
tempting to restart unit to allow switch to reset.  
Starter Handle  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Pull starter rope handle sharply until en-  
gine starts and runs.  
Locking/Release  
Button  
5. Allow unit to run for 10--15 seconds, then  
fully squeeze the throttle trigger to disen-  
gage the starting system.  
Coupler  
Attachment  
3. While securely holding the engine and  
upper shaft, pull the attachment straight  
out of the coupler.  
STARTING A WARM ENGINE  
1. Squeeze and hold the throttle trigger.  
Keep throttle trigger fully squeezed until  
engine runs smoothly.  
Upper Shaft  
2. Pull starter rope sharply while squeezing  
throttle trigger until engine runs.  
INSTALLING OPTIONAL ATTACH-  
NOTE: Normally, the warm starting procedure  
can be used within 5--10 minutes after the unit is  
turned off. If the unit sits for more than 10 min-  
utes without being ran, it will be necessary to  
start the unit by following the steps under  
STARTING A COLD ENGINE or following the  
starting instruction steps shown on the unit.  
MENTS  
1. Remove the shaft cap from the attach-  
ment (if present).  
2. Position locking/release button of attach-  
ment into guide recess of coupler.  
3. Push the attachment into the coupler until  
the locking/release button snaps into the  
primary hole.  
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing  
the start lever to the RUN position. Fully  
squeeze throttle trigger. Pull the starter han-  
dle repeatedly while squeezing throttletrigger  
until engine starts and runs. This could re-  
quire pulling the starter handle many times,  
depending on how badly the unit is flooded.  
If the unit still doesn’t start, refer to  
TROUBLESHOOTING TABLE or call  
1-800-554-6723.  
4. Before using the unit, tightenthe knob se-  
curely by turning clockwise.  
Coupler  
Primary Hole  
Guide Recess  
Locking/  
Release  
Button  
Upper  
Shaft  
Attachment  
OPERATING THE COUPLER  
This model is equipped with a coupler which  
enables optional attachments to be installed.  
The optional attachments are:  
WARNING: Make sure the locking/  
release button is locked in the primary hole  
and the knob is securely tightened before op-  
erating the unit. All attachments are designed  
to be used in the primary hole unless otherwise  
stated in the applicable attachment instruction  
manual. Using the wrong hole could lead to seri-  
ous injury or damage to the unit.  
MODEL:  
Cultivator . . . . . . . . . . . . . . . . . . . PP2000T  
Blower . . . . . . . . . . . . . . . . . . . . . PP3000B  
Brushcutter . . . . . . . . . . . . . . . . . PP4000C  
Pruner . . . . . . . . . . . . . . . . . . . . . PP5000P  
Pruner . . . . . . . . . . . . . . . . . . . . . PP5500P  
WARNING: Always stop unit anddis-  
connect spark plug before removing or instal-  
ling attachments.  
REMOVING LINE TRIMMER ATTACH-  
MENT, EDGER ATTACHMENT OR  
OTHER OPTIONAL ATTACHMENTS  
CAUTION: When removing or installing at-  
tachments, place the unit on a flat surface for  
stability.  
1. Loosen the coupler by turning the knob  
counterclockwise.  
Locking/Release  
Button in Primary Hole  
Upper Shaft  
OPERATING INSTRUCTIONS  
It is recommended that the engine not be  
operated for longer than 1 minute at full  
throttle.  
Coupler  
LOOSEN  
Attachment  
TIGHTEN  
Knob  
2. Press and hold the locking/release button.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CUTTING METHODS  
LINE TRIMMER ATTACHMENT  
OPERATING POSITION  
WARNING: Use minimum speed  
and do not crowd the line when cutting around  
hard objects (rock, gravel, fence posts, etc.),  
whichcandamage the trimmer head, become  
entangled in the line, or be thrown causing a  
serious hazard.  
ALWAYS WEAR:  
Eye Protection  
S The tip of the line does the cutting. You will  
achieve the best performance and  
minimum line wear by not crowding the line  
into the cutting area. The right and wrong  
ways are shown below.  
Long Pants  
Tip of the Line  
Line Crowded Into  
Heavy Shoes  
Does The Cutting  
Work Area  
Cut from your right to your left.  
WARNING: Always wear eye protec-  
tion. Never lean over the trimmer head.  
Rocks or debris can ricochet or be thrown into  
eyes and face and cause blindness or other  
serious injury.  
Do not run the engine at a higher speed than  
necessary. The cutting line will cut efficiently  
when the engine is run at less than full throttle.  
At lower speeds, there is less engine noise and  
vibration. The cutting line will last longer and will  
be less likely to “weld” onto the spool.  
Right  
Wrong  
S The line will easily remove grass and  
weeds fromaround walls, fences, trees and  
flower beds, but it also can cut the tender  
bark of trees or shrubs and scar fences.  
S For trimming or scalping, use less than full  
throttle to increase line life and decrease head  
wear, especially:  
S During light duty cutting.  
S Near objects around which the line can  
wrap such as small posts, trees or fence  
wire.  
Always release the throttle trigger and allow the  
engine to return to idle speed when not cutting.  
To stop engine:  
S For mowing or sweeping, use full throttle for  
a good clean job.  
TRIMMING -- Hold the bottom of the trimmer  
head about 3 inches (8 cm) above the ground  
and at an angle. Allow only the tip of the line to  
make contact. Do not force trimmer line into  
work area.  
S Release the throttle trigger.  
S Push and release the engine ON/STOP  
switch.  
TRIMMER LINE ADVANCE  
The trimmer line will advance approximately 2  
inches (5 cm) each time the bottom of the  
trimmer head is tapped on the ground with the  
engine running at full throttle.  
Trimming  
The most efficient line length is the maximum  
length allowed by the line limiter.  
Always keep the shield in place when the tool  
is being operated.  
3 inches (8 cm)  
above ground  
To advance line:  
S Operate the engine at full throttle.  
S Hold the trimmer head parallel to andabove  
the grassy area.  
SCALPING -- The scalping technique re-  
moves unwanted vegetation down to the  
ground. Hold the bottom of the trimmer head  
about 3 inches (8 cm) above the ground and  
at an angle. Allow the tip of the lineto strikethe  
ground around trees, posts, monuments, etc.  
This technique increases line wear.  
S Tap the bottom of the trimmer head lightly on  
the ground one time. Approximately 2 inches  
(5 cm) of line will be advanced with each tap.  
Always tap the trimmer head on a grassy  
area. Tapping on surfaces such as concrete  
or asphalt can cause excessive wear to the  
trimmer head.  
Scalping  
If the line is worn down to 2 inches (5 cm) or  
less, more than one tap will be required to ob-  
tain the most efficient line length.  
WARNING: Use only 0.080(2 mm)  
diameter line. Other sizes of line will not ad-  
vance properly and can cause serious injury.  
Do not use other materials such as wire,  
string, rope, etc. Wire can break off during  
cutting and become a dangerous missile that  
can cause serious injury.  
MOWING -- Your trimmer is ideal for mowing  
in places conventional lawn mowers cannot  
reach. In the mowing position, keep the line  
parallel to the ground. Avoid pressing the  
head into the ground as this can scalp the  
ground and damage the tool.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDGING  
Mowing  
As you become familiar with use of your edger  
attachment, you will be able to determine your  
own operating pace.  
Conditions such as depth of cut and material  
being cut will regulate the speed and time re-  
quired for your edging job.  
S Allow the engine to warm up before you begin  
edging.  
SWEEPING -- The fanning action of the rotat-  
ing line can be used for a quick and easy  
clean up. Keep the line parallel to and above  
the surfaces being swept and move the tool  
from side to side.  
S Increase the engine speed before placing the  
blade in the cut. For best results, run the en-  
gine at full throttle while cutting.  
S Always work going away from people and  
solid objects such as walls, large stones,  
trees, automobiles, etc.  
Swee
S Be careful when edging near trees or valuable  
plants. The high speed metal blade may cut  
roots and cause damage to the plants.  
S If the blade stalls, immediately move the unit  
back slightly to allow the blade to restart. If the  
blade continues to stall, stop the engine, dis-  
connect the spark plug, and inspect for block-  
age or damage.  
EDGER ATTACHMENT  
OPERATING POSITION  
WARNING: Keep the blade area  
clean. Always release the throttle trigger,  
push and release the engine ON/STOP  
switch, disconnect the spark plug and make  
sure the blade has completely stopped turn-  
ing before cleaning.  
ALWAYS WEAR:  
Head Protection  
Hearing  
Protection  
SETTING THE EDGING DEPTH  
Eye Protection  
WARNING: Never attempt to adjust  
the cut depth when the engine is running. Al-  
ways release the throttle trigger, wait until the  
blade stops turning, push and release the en-  
gine ON/STOP switch, and disconnect spark  
plug before making adjustments.  
Depth Adjustment  
Long Pan
Heavy Sho
Knob  
When operating unit, stand as shown and  
check for the following:  
S Wear eye protection and heavy clothing.  
S Keep right arm slightly bent with right hand  
holding the trigger handle of powerhead.  
S Keep left arm extended with left hand  
holding the handle.  
1. Loosen the depth adjustment knob.  
2. Slide the wheel to the desired position.  
S Raising the wheel will increase the cut-  
ting depth.  
S Keep unit below waist level.  
S Adjust edger wheel for proper cut depth.  
S Lowering the wheel will decrease the  
cutting depth.  
WARNING: Never attempt to adjust  
the edger wheel when the unit is in operation.  
Always stop the powerhead, wait until the  
blade stops turning, and disconnect thespark  
plug before making adjustments.  
3. Tighten the depth adjustment knob se-  
curely.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Button  
WARNING: Disconnect the spark  
plug before performing maintenance except  
for carburetor adjustments.  
Air Filter  
HELPFUL TIP  
IMPORTANT: Have all  
repairs other than the rec-  
ommended maintenance  
described in the instruction  
ir Filter Cover  
manual performed by an  
authorized service dealer.  
If any dealer other than an authorized  
service dealer performs work on the  
product, Poulan PRO may not pay for  
repairs under warranty. It is your re-  
sponsibility to maintain and perform  
general maintenance.  
MUFFLER AND SPARK ARREST-  
ING SCREEN  
WARNING: The muffler on this prod-  
uct contains chemicals known to the State of  
California to cause cancer.  
As your unit is used, carbon deposits build up  
on the muffler and spark arresting screen.  
For normal homeowner use, however, the  
muffler and spark arresting screen will not re-  
quire any service. After 50 hours of use, we  
recommend that your muffler be serviced or  
replaced by your authorized service dealer.  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
S Assist Handle Screw  
S Debris Shield  
S Blade Nut  
CHECK FOR DAMAGED OR  
REPLACE SPARK PLUG  
WORN PARTS  
Replace the spark plug each year to ensure  
the engine starts easier and runs better. Set  
spark plug gap at 0.025 inch (0.6 mm). Igni-  
tion timing is fixed and nonadjustable.  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and  
discard.  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S ON/STOP Switch -- Ensure ON/STOP  
switch functions properly by pushing and  
releasing the switch. Make sure engine  
stops. Wait 5 seconds before attempting to  
restart unit to allow switch to reset. Restart  
engine and continue.  
S Fuel Tank -- Discontinue use of unit if fuel  
tank shows signs of damage or leaks.  
S Debris Shield -- Discontinue use of unit if  
debris shield is damaged.  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
(19 mm) socket wrench.  
4. Reinstall the spark plug boot.  
EDGER BLADE MAINTENANCE  
INSPECT AND CLEAN UNIT AND  
WARNING: The blade will continue  
to spin after the engine stops or after the  
throttle trigger has been released. To avoid  
serious injury, make sure the blade has  
stopped coasting and disconnect the spark  
plug before performing work on the blade.  
LABELS  
S After each use, inspect complete unit for  
loose or damaged parts. Clean the unit and  
labels using a damp cloth with a mild deter-  
gent.  
S Wipe off unit with a clean dry cloth.  
WARNING: Always replace a blade  
that is bent, warped, cracked, broken, or  
damaged in any other way. Never attempt to  
straighten and reuse a damaged blade. Use  
only specified replacement blade. Wear pro-  
tective gloves when handling or performing  
maintenance on the blade to help avoid injury.  
S The blade is reversible. When the cutting  
edge on one side becomes worn, turn the  
blade over (see BLADE REPLACEMENT  
in the SERVICE AND ADJUSTMENTS  
section).  
CLEAN AIR FILTER  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean after every  
5 hours of operation.  
1. Clean the cover and the area around it to  
keep dirt from falling into the carburetor  
chamber when the cover is removed.  
2. Remove parts by pressing button to re-  
lease air filter cover.  
NOTE: To avoid creating a fire hazard or  
producing harmful evaporative emissions, do  
not clean filter in gasoline or other flammable  
solvent.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
5. Replace parts.  
S Check blade for flatness periodically. Lay  
the blade on a flat surface to inspect for  
flatness. Throw away a blade that is not flat.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
5. When installing new line on an existing  
REPLACING THE LINE  
spool, hold the spool as shown.  
6. Bend the line at the midpoint and insert  
the bend into the slot in the center rim of  
the spool. Ensure line snaps into position  
in the slot.  
1. Press the tabs on the side of the trimmer  
head and remove cover and spool.  
Tab  
Tab  
7. With your finger between the lines, wrap  
the lines evenly and firmly around the  
spool in a clockwise direction.  
C
Spool  
8. Position the lines in the guide slots.  
Guide slot  
Guide slot  
2. Remove any remaining line.  
3. Clean dirt and debris from all parts. Re-  
place spool if it is worn or damaged.  
4. Replace with a pre-wound spool, or re-  
place line using a 25 feet (8 meters)  
length of 0.080 inch (2 mm) diameter  
Poulan PRO brand line.  
WARNING: Never use wire, rope,  
string, etc., which can break off and becomea  
dangerous missile.  
9. Place the spool in the cover as shown  
below.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dust
2. Remove trimmer head by turning coun-  
terclockwise (looking from bottom of  
unit).  
3. Thread replacement trimmer head onto the  
shaft by turning clockwise. Only tighten  
hand tight!  
EDGER BLADE REPLACEMENT  
10. Insert the ends of the lines through exit  
holes in the sides of the cover.  
Line exit hole  
WARNING: The blade will continue  
to spin after the engine stops or after the  
throttle trigger has been released. To avoid  
serious injury, make sure the blade has  
stopped coasting and disconnect the spark  
plug before performing work on the blade.  
ver  
WARNING: Wear protective gloves  
when handling or performing maintenance on  
the blade to avoid injury. The blade is sharp and  
can cut you even when it is not moving.  
1. To remove the blade, alignhole in thedust  
cup with the hole in the side of the gear-  
box by rotating the blade.  
2. Insert a small screwdriver into aligned  
holes. This will keep the shaft from turn-  
ing while loosening the blade nut.  
11. Reinstall the spool and cover onto the  
trimmer head. Push untilcover snaps into  
place.  
Screwdriv
3. While holding the screwdriver in position,  
remove blade nut by turning clockwise.  
4. Remove both washers, and the blade  
from the blade shaft.  
Blade shield  
Blade  
Washers  
Blade Shaft  
Blade nut  
5. Install new blade onto blade shaft.  
6. Reinstall both washers and blade nut  
(counterclockwise).  
7. Tighten blade nut firmly with a wrench  
while holding screwdriver in position.  
8. Remove the screwdriver.  
9. Turn blade by hand. If the blade binds  
against the shield, or appears to be un-  
even, the blade is not centered, and you  
must reinstall.  
REPLACING THE TRIMMER HEAD  
1. Hold the dust cup with a wrench to keep  
the shaft from turning while removing and  
installing trimmer head.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Turn idle speed screw clockwise to increase  
engine speed if engine stalls or dies.  
CARBURETOR IDLE SPEED  
ADJUSTMENT  
S Turn idle speed screw counterclockwise to  
decrease engine speed if trimmer head or any  
optional attachment moves or spins at idle.  
WARNING: Keep others away when  
making idle speed adjustments. The trimmer  
head or any optional attachment will be spin-  
ning during most of this procedure. Wear your  
protective equipment and observe all safety  
precautions. After making adjustments, the  
trimmer head or any optional attachment  
must not move/spin at idle speed.  
WARNING: Recheck the idle speed  
after each adjustment. The trimmer head or  
any optional attachment must not move or  
spin at idle speed toavoid serious injury tothe  
operator or others.  
The carburetor has been carefully set at the  
factory. Adjustments may benecessary if you  
notice any of the following conditions:  
S Engine will not idle when the throttle is  
released.  
S The trimmer head or any optional  
attachment moves/spins at idle.  
Make adjustments with the unit supported so  
the cutting attachment is off the ground and  
will not make contact with any object.  
Hold the unit by hand while running and mak-  
ing adjustments. Keep all parts of your body  
away from the cutting attachment and muffler.  
To adjust idle speed:  
Allow engine to idle. Adjust speed until engine  
runs without trimmer head or any optional at-  
tachment moving or spinning (idle too fast) or  
engine stalling (idle speed too slow).  
If you require further assistanceor are unsure  
about performing this procedure, contact an  
authorized  
service  
dealer  
or  
call  
1--800--554--6723.  
STORAGE  
Fuel stabilizer is an acceptable alternative in  
minimizing the formation of fuel gum deposits  
during storage. Add stabilizer to the gasoline  
in the fuel tank or fuel storage container. Fol-  
low the mix instructions found on stabilizer  
container. Run engine at least 5 minutes after  
adding stabilizer.  
WARNING: Perform the following  
steps after each use:  
S Allow engine to cool before storing or trans-  
porting.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
S Store unit and fuel well out of the reach of  
children.  
SEASONAL STORAGE  
HELPFUL TIP  
During storage of your gas/  
oil mixture, the oil will sepa-  
rate from the gas.  
We recommend that you  
shake the gas can weekly  
to insure proper blending of  
the gas and oil.  
Prepare unit for storage at end of season or if  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Check entire unit for loose screws or nuts.  
Replace any damaged, worn or broken parts.  
S Clean the entire unit before lengthy  
storage.  
ENGINE  
S Remove spark plug and pour 1 teaspoon of  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range.  
S Store in a clean dry area.  
S Inspect the blade shield area and clean any  
dirt, grass, leaves, or debris that has col-  
lected. Inspect the blade and blade shield; re-  
place a blade that is bent, warped, cracked,  
broken or damaged in any other way.  
S Lightly oil external metal surfaces.  
S Apply a coating of oil to the entire surface of  
the blade; wrap it in heavy paper or cloth.  
S Clean air filter.  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
S At the beginning of the next season, use  
only fresh fuel having the proper gasolineto  
oil ratio.  
FUEL SYSTEM  
OTHER  
Under FUELING ENGINE in the OPERA-  
TION section of this manual, see messagela-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine.  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts to rust.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing all of the  
recommended remedies below except remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
Engine will not  
start.  
1. Engine flooded.  
1. See “Starting a Flooded Engine” in  
Operation Section.  
2. Fuel tank empty.  
3. Spark plug not firing.  
4. Fuel not reaching  
carburetor.  
2. Fill tank with correct fuel mixture.  
3. Install new spark plug.  
4. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
5. Carburetor requires  
adjustment.  
5. Contact an authorized service dealer.  
Engine will  
not idle  
properly.  
1. Carburetor requires  
adjustment.  
1. See “Carburetor Idle Speed Adjustment”  
in Service and Adjustments Section.  
2. Crankshaft seals worn. 2. Contact an authorized service dealer.  
3. Compression low.  
3. Contact an authorized service dealer.  
1. Air filter dirty.  
1. Clean or replace air filter.  
2. Clean or replace plug  
and regap.  
Engine will not  
accelerate,  
lacks power,  
or dies under  
a load.  
2. Spark plug fouled.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
5. Compression low.  
3. Contact an authorized service dealer.  
4. Contact an authorized service dealer.  
5. Contact an authorized service dealer.  
Engine  
1. Fuel mixture incorrect. 1. Empty fuel tank and refill with  
correct fuel mixture.  
smokes  
excessively.  
2. Air filter dirty.  
3. Carburetor requires  
adjustment.  
2. Clean or replace air filter.  
3. Contact an authorized service dealer.  
1. Fuel mixture incorrect.  
1. See “Fueling Engine” in Operation  
section.  
Engine runs  
hot.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
2. Replace with correct spark plug.  
3. Contact an authorized service dealer.  
4. Contact an authorized service dealer.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
Poulan PRO, a division of Husqvarna Consum-  
In Canada, contact:  
er Outdoor Products N.A., Inc., warrants to the  
original consumer purchaser that each new  
Poulan PRO brand gasoline tool or attachment  
is free from defects in material and workman-  
ship and agrees to repair or replace under this  
warranty any defective gasoline product or at-  
tachment as follows from the original date of  
purchase.  
Poulan PRO  
850 Matheson Blvd. West  
Mississauga, Ontario L5V 0B4  
Giving the model number, serial number and  
date of purchase of your product and the name  
and address of the authorized dealer from  
whom it was purchased.  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE OTH-  
ER RIGHTS WHICH VARY FROM STATE TO  
STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE LIM-  
ITATIONS OR EXCLUSION MAY NOT APPLY  
TO YOU.  
This is a limited warranty within the meaning of  
that term as defined in the Magnuson--Moss Act  
of 1975.  
2 YEARS - Parts and Labor, when used for  
household purposes.  
90 DAYS - Parts and Labor, when used for  
commercial, professional, or income producing  
purposes.  
30 DAYS - Parts and Labor, if used for rental  
purposes.  
This warranty is not transferable and does not  
cover damage or liability caused by improper  
handling, improper maintenance or alteration, or  
the use of accessories and/or attachments not  
specifically recommended by Poulan PRO for  
this tool. This warranty does not cover tune--up,  
spark plugs, filters, starter ropes, cutting line, or  
rotating head parts that will wear and require re-  
placement with reasonable use during the war-  
ranty period. This warranty does not cover pre--  
delivery setup or normal adjustments explained  
in the instruction manual. This warranty does  
not cover transportation costs.  
The policy of Poulan PRO is to continuously  
improve its products. Therefore, Poulan PRO  
reserves the right to change, modify, or dis-  
continue models, designs, specifications,  
and accessories of all products at any time  
without notice or obligation to any purchaser.  
In the event you have a claim under this warran-  
ty, you must return the product to an authorized  
service dealer.  
Should you have any unanswered questions  
concerning this warranty, please contact:  
Poulan PRO, a division of Husqvarna  
Consumer Outdoor Products N.A., Inc.  
1030 Stevens Creek Road  
Augusta, GA 30907  
1--800--554--6723  
U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OB-  
LIGATIONS: The U.S. Environmental  
Protection Agency, California Air Resources  
Board, Environment Canada and Poulan  
PRO are pleased to explain the emissions con-  
trol system warranty on your year 2009 and lat-  
er small off--road engine. In California, all small  
off--road engines must be designed, built, and  
equipped to meet the State’s stringent anti--  
smog standards. Poulan PRO must warrant  
the emission control system on your small  
off--road engine for the periods of time listed  
below provided there has been no abuse, ne-  
glect, or improper maintenance of your small  
off--road engine. Your emission control system  
includes parts such as the carburetor, the igni-  
tion system and the fuel tank. Where a warrant-  
able condition exists, Poulan PRO will repair  
your small off--road engine at no cost to you.  
Expenses covered under warranty include  
diagnosis, parts and labor.  
MANUFACTURER’S WARRANTY COV-  
ERAGE: If any emissions related part on your  
engine (as listed under Emissions Control  
Warranty Parts List) is defective or a defect in  
the materials or workmanship of the engine  
causes the failure of such an emission related  
part, the part will be repaired or replaced by  
Poulan PRO. OWNER’S WARRANTY RE-  
SPONSIBILITIES: As the small off--road en-  
gine owner, you are responsible for the per-  
formance of the required maintenance listed  
in your instruction manual. Poulan PRO rec-  
ommends that you retain all receipts covering  
maintenance on your small off--road engine,  
but Poulan PRO cannot deny warranty solely  
for the lack of receipts or for your failure to en-  
sure the performance of all scheduled main-  
tenance. As the small off--road engine owner,  
you should be aware that Poulan PRO may  
deny you warranty coverage if your small off--  
road engine or a part of it has failed due to  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
abuse, neglect, improper maintenance, un-  
approved modifications, or the use of parts  
not made or approved by the original equip-  
ment manufacturer. You are responsible for  
presenting your small off--road engine to an  
Poulan PRO authorized repair center as soon  
as a problem exists. Warranty repairs should be  
completed in a reasonable amount of time, not  
to exceed 30 days. If you have any questions  
regarding your warranty rights and responsi-  
bilities, you should contact your nearest autho-  
rized service center, call Poulan PRO at  
1--800--554--6723, or send e-mail correspon-  
labor which leads to the determination that a  
warranted part is defective if the diagnostic  
work is performed at an approved Poulan  
PRO servicing center. CONSEQUENTIAL  
DAMAGES: Poulan PRO may be liable for  
damages to other engine components caused  
by the failure of a warranted part still under war-  
ranty. WHAT IS NOT COVERED: All failures  
caused by abuse, neglect, or improper mainte-  
nance are not covered. ADD-ON OR MODI-  
FIED PARTS: The use of add--on or modified  
parts can be grounds for disallowing a warranty  
claim. Poulan PRO is not liable to cover failures  
of warranted parts caused by the use of add--on  
or modified parts. HOW TO FILE A CLAIM: If  
you have any questions regarding your warran-  
ty rights and responsibilities, you should contact  
your nearest authorized service center, call  
Poulan PRO at 1--800--554--6723, or send  
e-mail correspondence to emission.warranty  
@HCOP--emission.com. WHERE TO GET  
WARRANTY SERVICE: Warranty services or  
repairs shall be provided at all Poulan PRO ser-  
vice centers. Call: 1--800--554--6723 or send  
e-mail correspondence to emission.warranty  
@HCOP--emission.com. MAINTENANCE,  
REPLACEMENT AND REPAIR OF EMIS-  
SION RELATED PARTS: Any Poulan PRO  
approved replacement part used in the per-  
formance of any warranty maintenance or re-  
pair on emission related parts will be provided  
without charge tothe owner if thepart is under  
warranty. EMISSION CONTROL WARRAN-  
TY PARTS LIST: Carburetor, air filter (covered  
up to maintenance schedule), ignition system:  
spark plug (covered up to maintenance sched-  
ule), ignition module, muffler including catalyst (if  
equipped), fuel tank. MAINTENANCE  
STATEMENT: The owner is responsible for  
the performance of all required maintenance  
as defined in the instruction manual.  
dence  
to  
emission.warranty@HCOP--  
emission.com. WARRANTY COMMENCE-  
MENT DATE: The warranty period begins on  
the date the small off--road engine is pur-  
chased. LENGTH OF COVERAGE: This  
warranty shall be for a period of two years  
from the initial date of purchase. WHAT IS  
COVERED: REPAIR OR REPLACEMENT  
OF PARTS. Repair or replacement of any  
warranted part will be performed at no charge  
to the owner at an approved Poulan PRO  
servicing center. If you have any questions  
regarding your warranty rights and responsi-  
bilities, you should contact your nearest au-  
thorized service center, call Poulan PRO at  
1--800--554--6723, or send e-mail correspon-  
dence  
to  
emission.warranty@HCOP--  
emission.com. WARRANTY PERIOD: Any  
warranted part which is not scheduled for re-  
placement as required maintenance, or which  
is scheduled only for regular inspection to the  
effect of “repair or replaceas necessary” shall  
be warranted for 2 years. Any warranted part  
which is scheduled for replacement as re-  
quiredmaintenance shall bewarranted for the  
period of time up to the first scheduled re-  
placement point for that part. DIAGNOSIS:  
The owner shall not be charged for diagnostic  
The information on the product label indicates which standard your engine is certified.  
Example: (Year) EPA and/or CALIFORNIA.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Coffeemaker HD7805 User Manual
Philips Flat Panel Television SA9100 User Manual
Philips Speaker BS100 User Manual
Philips TV VCR Combo 14PV350 07 User Manual
Pioneer DVD Recorder DVR 920H User Manual
Pioneer Stereo Receiver VSX 59TXi User Manual
Polaroid Car Video System PDU 1045S User Manual
Polaroid MP3 Player PMP500 4 User Manual
Polycom Elliptical Trainer 3725 22370 001 B User Manual
Poulan Snow Blower 414643 User Manual