Poulan Blower PPB200 LE User Manual

R
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
PPB2000 LE  
IMPORTANT MANUAL -- Do not throw away  
MANUAL IMPORTANTE -- No lo descarte  
MANUEL IMPORTANT -- À Conserver  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en le-  
siones graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le  
faire pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
104 Warren Road  
Augusta, GA 30907  
Copyright E2004 Electrolux Home Products, Inc.  
530164283  
2/5/04  
Download from Www.Somanuals.com. All Manuals Search And Download.  
disconnected. Keep vents and discharge  
tubes free of debris which can accumulate  
and restrict proper air flow.  
D Never place any object in the air intake open-  
ing as this could restrict proper air flow and  
cause damage to the unit.  
D Never use for spreading chemicals, fertiliz-  
ers, or other substances which may contain  
toxic materials.  
SPECIAL NOTICE: Exposure to vibra-  
tions through prolonged use of gasoline pow-  
ered hand tools could cause blood vessel or  
nerve damage in the fingers, hands, and  
joints of people prone to circulation disorders  
or abnormal swelling. Prolonged use in cold  
weather has been linked to blood vessel dam-  
age in otherwise healthy people. If symptoms  
occur such as numbness, pain, loss of  
strength, change in skin color or texture, or  
loss of feeling in the fingers, hands, or joints,  
discontinue the use of this tool and seek  
medical attention. An antivibration system  
does not guarantee the avoidance of these  
problems. Users who operate power tools on  
a continual and regular basis must monitor  
closely their physical condition and the condi-  
tion of this tool.  
D To avoid spreading fire, do not use near leaf  
or brush fires, fireplaces, barbecue pits,  
ashtrays, etc.  
D Use only for jobs explained in this manual.  
MAINTAIN YOUR UNIT PROPERLY  
D Have all maintenance other than the rec-  
ommended procedures described in the in-  
struction manual performed by an autho-  
rized service dealer.  
D Disconnect spark plug before performing  
maintenance except for carburetor adjust-  
ments.  
D Use only recommended Poulan PRO! re-  
placement parts; use of any other parts  
may void your warranty and cause damage  
to your unit.  
D Empty fuel tank before storing the unit. Use  
up fuel left in carburetor by starting engine and  
letting it run until it stops.  
D Do not use any accessory or attachment  
other than those recommended by manufac-  
turer for use with your unit.  
D Do not store the unit or fuel in a closed area  
where fuel vapors can reach sparks or an  
open flame from hot water heaters, electric  
motors or switches, furnaces, etc.  
D Store in a dry area out of reach of children.  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442 and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equipped with a spark arresting screen. If you  
operate in a locale where such regulations ex-  
ist, you are legally responsible for maintaining  
the operating condition of these parts. Failure  
to do so is a violation of the law. Refer to the  
MAINTENANCE section for information on  
maintenance of the muffler and spark arrest-  
ing screen.  
ASSEMBLY  
Blower  
Outlet  
Blower  
Tube  
WARNING: Stop engine and be sure  
the impeller blades have stopped turning be-  
fore opening the vacuum inlet door or at-  
tempting to insert or remove the vacuum or  
blower tubes. The rotating blades can cause  
serious injury. Always disconnect the spark  
plug before performing maintenance or ac-  
cessing movable parts.  
Groove  
Rib  
2. Secure the tube by turning the knob clock-  
wise.  
WARNING: If you receive your unit  
assembled, check each step to insure your  
unit is properly assembled and all fasteners  
are secure. Follow all safety information in  
the manual and on the unit.  
3. To remove the tube, turn the knob counter-  
clockwise to loosen the tube; remove the  
tube.  
VACUUM BAG ASSEMBLY  
1. Open the zipper on the vacuum bag and  
insert the elbow tube.  
D
A standard screwdriver is required for as-  
sembly.  
2. Push the small end of the elbow tube  
through the small opening in the bag.  
Elbow  
BLOWER TUBE ASSEMBLY  
1. Align the rib on the blower tube with the  
groove in the blower outlet; slide the tube  
into place.  
NOTE: Knob must be loose enough to allow  
blower tube to be inserted in blower outlet.  
Loosen knob by turning counterclockwise.  
Tube  
Small  
Opening  
Zipper  
Opening  
Rib  
-- 3 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Hold the vacuum inlet cover open until up-  
per vacuum tube is installed.  
NOTE: Make sure edge of the small opening  
is flush against the flared area of the elbow  
tube, and the rib on the elbow tube is on the  
bottom.  
Vacuum Inlet  
3. Close the zipper on the bag. Make sure the  
zipper is closed completely.  
4. Remove blower tube from engine.  
Retaining Post  
Vacuum  
Inlet  
Cover  
Rib  
5. Place the hooks of the upper vacuum tube  
on the retaining posts of the unit.  
6. Pivot the tube until it is secured to the  
blower unit by the vacuum inlet latch.  
Groove  
PIVOT  
Inlet Cover  
Latch  
5. Insert the elbow tube into the blower outlet.  
Make sure elbow tube rib is aligned with  
the blower outlet groove.  
6. Turn knob clockwise to secure elbow tube.  
VACUUM TUBE ASSEMBLY  
WARNING: Stop engine and be sure  
the impeller blades have stopped turning be-  
fore opening the vacuum inlet door or at-  
tempting to insert or remove the vacuum or  
blower tubes. The rotating blades can cause  
serious injury.  
1. Align the lower vacuum tube as shown.  
Push lower vacuum tube into upper vacu-  
um tube.  
Retaining  
Hook  
Post  
HOW TO CONVERT UNIT FROM  
VACUUM USE TO BLOWER USE  
1. Remove the vacuum tubes by inserting  
the tip of a screwdriver into the latch area  
of the vacuum inlet.  
2. Gently tilt handle of screwdriver toward  
the back of the unit to release the latch  
while pulling up on the upper vacuum tube  
with your other hand.  
Upper Vacuum  
Tube  
Latch Area  
Lower Vacuum Tube  
2. Insert the tip of a screwdriver into the latch  
area of the vacuum inlet.  
Blower  
Outlet  
Latch  
Ar
Latch Area  
Vacuum  
Inlet Cover  
3. Remove the vacuum bag.  
3. Gently tilt the handle of the screwdriver to- 4. Close the vacuum inlet cover and make  
ward the back of the unit to release the  
latch while pulling up on the vacuum inlet 5. Reinstall the blower tube (see BLOWER  
cover with your other hand. TUBE ASSEMBLY).  
sure it is latched closed.  
-- 4 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHOULDER STRAP ADJUSTMENT  
1. Hold the unit as shown with the muffler side  
facing away from your body and clothes.  
2. Pass the shoulder strap over your head  
and onto your right shoulder.  
3. Extend your left arm toward the rear of the  
vacuum bag.  
4. Adjust shoulder strap until the vacuum  
bag/shoulder strap seam lies between  
your thumb and index finger.  
5. Make sure air flows freely from the elbow  
tube into bag. If bag is kinked, the unit will  
not operate properly.  
OPERATION  
KNOW YOUR BLOWER  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.  
Compare the illustrations with your unit to familiarize yourself with the location of the various controls  
and adjustments. Save this manual for future reference.  
Upper  
Lower  
Vacuum Tube  
Primer Button  
Choke Lever  
Vacuum Bag  
Fuel Mix  
Throttle  
Fill Cap  
Lever  
Starter  
Rope  
Spark Plug  
Elbow Tube  
Blower  
Tube  
Rear  
Handle  
THROTTLE LEVER  
CHOKE LEVER  
The CHOKE helps to supply fuel to the engine  
The THROTTLE LEVER is used to select the  
desired engine speed and to stop the engine. to aid in cold starting. Activate the choke by  
moving the choke lever to the FULL CHOKE  
position. After engine attempts to start, move the  
choke lever to the HALF CHOKE position.  
Once engine starts, move choke lever to the  
RUN position.  
Move the throttle lever to the  
full speed operation. Move the throttle lever  
to the position for idle speed. To stop the  
position for  
engine, move the throttle lever to the STOP  
position.  
PRIMER BUTTON  
The PRIMER BUTTON removes air from the  
carburetor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate primer button  
by pressing it and allowing it to return to its origi-  
nal position.  
-- 5 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This engine is certified to operate on  
unleaded gasoline. Before operation,  
gasoline must be mixed with a good quality  
synthetic 2-cycle air-cooled engine oil  
designed to be mixed at a ratio of 40:1.  
Poulan/Weed Eater! brand synthetic oil is  
recommended. Mix gasoline and oil at a ratio  
of 40:1. A 40:1 ratio is obtained by mixing 3.2  
ounces (95 ml) of oil with 1 gallon (4 liters) of  
unleaded gasoline. DO NOT USE automotive  
oil or marine oil. These oils will cause engine  
damage. When mixing fuel, follow  
instructions printed on container. Once oil is  
added to gasoline, shake container  
momentarily to assure that the fuel is  
thoroughly mixed. Always read and follow the  
safety rules relating to fuel before fueling your  
unit.  
OPERATING POSITION  
ye  
otec
Blower  
Vacuum  
OPERATING TIPS  
IMPORTANT  
S While vacuuming or blowing debris, hold  
the unit with the muffler side facing away  
from your body and clothes (see OPERAT-  
ING POSITION illustration above).  
S To reduce the risk of hearing loss  
associated with sound level(s), hearing  
protection is required.  
Experience indicates that alcohol blended  
fuels (called gasohol or using ethanol or  
methanol) can attract moisture which leads to  
separation and formation of acids during  
storage. Acidic gas can damage the fuel  
system of an engine while in storage. To avoid  
engine problems, empty the fuel system  
before storage for 30 days or longer. Drain the  
gas tank, start the engine and let it run until the  
fuel lines and carburetor are empty. Use fresh  
fuel next season. Never use engine or  
carburetor cleaner products in the fuel tank or  
permanent damage may occur.  
S To reduce the risk of injury associated with  
contacting rotating parts, stop the engine be-  
fore installing or removing attachments. Do  
not operate without guard(s) in place.  
S Operate power equipment only at reasonable  
hours--not early in the morning or late at night  
when people might be disturbed. Comply with  
times listed in local ordinances. Usual recom-  
mendations are 9:00 a.m. to 5:00 p.m.,  
Monday though Saturday.  
NOTE: Unit must be placed on its side when  
adding fuel (see illustration below).  
S To reduce noise levels, limit the number of  
pieces of equipment used at any one time.  
S To reduce noise levels, operate power  
blowers at the lowest possible throttle  
speed to do the job.  
S Use rakes and brooms to loosen debris be-  
fore blowing.  
S In dusty conditions, slightly dampen sur-  
faces or use a mister attachment when wa-  
ter is available.  
S Conserve water by using power blowers  
instead of hoses for many lawn and garden  
applications, including areas such as gutters,  
screens, patios, grills, porches, and gardens.  
S Watch out for children, pets, open windows,  
or freshly washed cars. Blow debris away  
safely.  
S Use the full blower nozzle extension so the  
air stream can work close to the ground.  
S After using blowers and other equipment,  
CLEAN UP! Dispose of debris in trash re-  
ceptacles.  
TO STOP THE ENGINE  
D To stop the engine, move the throttle lever  
to the STOP position.  
BEFORE STARTING ENGINE  
BEFORE STARTING THE ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you be-  
gin. If you do not understand the safety rules,  
do not attempt to fuel your unit. Call  
1-800-554-6723.  
WARNING: You MUST make sure  
the tubes are secure before using the unit.  
D
Fuel engine. Move at least 10 feet (3 me-  
ters) away from the fueling site.  
Hold the unit in the starting position as  
shown. Make sure the blower end is di-  
rected away from people, animals, glass,  
and solid objects.  
FUELING ENGINE  
D
WARNING: Remove fuel cap slowly  
when refueling.  
-- 6 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STARTING POSITION  
NOTE: If engine attempts to start before the  
th  
5
pull, go to next step immediately.  
5. Move the choke lever to the HALF  
CHOKE position.  
6. Pull the starter rope sharply until the en-  
gine runs, but no more than 5 pulls (below  
30_ F, 10 pulls).  
7. After a 5 second warm--up, move the  
choke lever to the RUN position.  
Blower  
8. Allow the unit to run for 30 more seconds  
at the RUN position before moving the  
throttle lever to the  
position.  
If engine has not started after 5 pulls (at HALF  
CHOKE), repeat STARTING A COLD ENGINE  
procedure. If engine still does not start, proceed  
to STARTING A FLOODED ENGINE.  
9. To stop the engine, move the throttle lever to  
the STOP position.  
WARNING: When starting engine,  
hold the unit as illustrated. Do not set unit on any  
surface except a clean, hard area when starting  
engine or while engine is running. Debris such  
as gravel, sand, dust, grass, etc. could be  
picked up by the air intake and thrown out  
through the discharge opening, damaging the  
unit or property, or causing serious injury to by-  
standers or the operator.  
STARTING A WARM ENGINE  
NOTE: If fuel tank is empty, add fuel; then,  
follow STARTING A COLD ENGINE proce-  
dure. Do not fill fuel tank while engine is hot.  
STARTING A COLD ENGINE  
1. Move throttle lever to the  
1. Move throttle lever to the  
position.  
position.  
2. Pull starter rope sharply until engine runs,  
but no more than 5 pulls.  
2. Move choke lever to the FULL CHOKE  
position.  
3. Slowly press the primer button 8 times.  
NOTE: If engine has not started, pull starter  
rope 5 more pulls. If engine still does not run,  
it is probably flooded.  
T
3. To stop the engine, move the throttle lever to  
the STOP position.  
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing the  
choke lever in the RUN position. Move throttle  
lever to the fast position  
; then, pull rope  
until engine starts. After engine starts, move the  
throttle lever to the slow position  
engine to idle.  
to allow  
Starting could require pulling the starter rope  
many times depending on how badly the unit is  
flooded.  
If unit still doesn’t start refer to the TROUBLE-  
SHOOTING TABLE or call 1-800-554-6723.  
Choke Lever  
4. Pull starter rope sharply until engine at-  
tempts to run, but no more than 5 pulls (be-  
low 30_ F, 8 pulls).  
MAINTENANCE  
instructed in this manual. Various adjust-  
ments will need to be made periodically to  
properly maintain your unit.  
WARNING: Avoid touching muffler  
unless engine and muffler are cold. A hot  
muffler can cause serious burns.  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
S Muffler  
WARNING: Stop engine and be sure  
the impeller blades have stopped turning be-  
fore opening the vacuum inlet door or at-  
tempting to insert or remove the vacuum or  
blower tubes. The rotating blades can cause  
serious injury. Always disconnect the spark CHECK FOR DAMAGED OR WORN  
plug before performing maintenance or ac-  
cessing movable parts.  
PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S Fuel Tank -- Do not use unit if fuel tank shows  
signs of damage or leaks.  
GENERAL RECOMMENDATIONS  
The warranty on this unit does not cover items  
that have been subjected to operator abuse  
or negligence. To receive full value from the  
warranty, the operator must maintain unit as  
S Vacuum Bag -- Do not use vacuum bag if it  
is torn or damaged.  
-- 7 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSPECT AND CLEAN UNIT AND  
DECALS  
S After each use, inspect complete unit for  
loose or damaged parts. Clean the unit and  
decals using a damp cloth with a mild deter-  
gent.  
Fuel Line  
S Wipe off unit with a clean dry cloth.  
CLEAN AIR FILTER  
Fuel Filter  
Air Filter  
Cover  
CHECK  
MUFFLER  
MOUNTING  
SCREWS  
Once each year, ensure muffler mounting  
screws are secure and tightened properly to  
prevent damage.  
Mounting  
Screw  
Holes  
Muffler Cover  
Screws  
Air Filter  
Screws  
Cleaning the air filter:  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean or replace  
air filter after every 5 hours of operation or  
yearly, whichever comes first.  
1. Clean the cover and the area around it to  
keep debris from falling into the carburetor  
chamber when the cover is removed.  
2. Remove parts as illustrated.  
NOTE: Do not clean filter in gasoline or other  
flammable solvent. Doing so can create a fire  
hazard or produce harmful evaporative emis-  
sions.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
1. Loosen and remove the 2 screws from the  
muffler cover.  
2. Remove the muffler cover.  
3. Tighten the 2 muffler mounting screws se-  
curely.  
4. Reinstall muffler cover and 2 screws.  
Tighten securely.  
INSPECT MUFFLER AND SPARK  
ARRESTING SCREEN  
WARNING: The muffler on this prod-  
uct contains chemicals known to the State of  
California to cause cancer.  
As the unit is used, carbon deposits build up  
on the muffler and spark arresting screen,  
and must be removed to avoid creating a fire  
hazard or affecting engine performance.  
5. Apply a few drops of oil to the filter;  
squeeze filter to distribute oil.  
6. Replace parts.  
REPLACE SPARK PLUG  
VIEW OF MUFFLER  
Replace spark plug each year to ensure the  
engine starts easier and runs better. Set  
spark plug gap at 0.025 inch (0.6 mm). Igni-  
tion timing is fixed, nonadjustable.  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and dis-  
card.  
Spark arresting  
screen  
Exhaust  
Diverter  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
(19 mm) socket wrench.  
Screws  
4. Reinstall the spark plug boot.  
REPLACE FUEL FILTER  
To replace fuel filter, drain unit by running it dry  
of fuel, then remove fuel cap/retainer assem-  
bly from tank. Pull filter from tank and remove  
it from the fuel line. Install new fuel filter on fuel  
line; reinstall parts.  
Replace the spark arresting screen every 50  
hours of operation or if any damage or breaks  
in the screen are noted.  
-- 8 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: Do not attempt to clean the spark ar-  
resting screen.  
1. Loosen and remove the 2 screws from the  
muffler cover. Remove the muffler cover.  
2. Loosen and remove both screws from the  
exhaust diverter.  
NOTE: If any part of the muffler is cracked,  
broken or damaged, we recommend that the  
muffler be replaced.  
CARBURETOR ADJUSTMENTS  
There is no screw for idle adjustment on your  
blower. The throttle lever is used to control  
engine speed. The throttle lever can be  
placed in one of four positions: STOP, IDLE  
3. Remove the exhaust diverter and spark  
arresting screen.  
4
Install new spark arresting screen.  
or  
, FULL THROTTLE or  
, and one  
5. Reinstall exhaust diverter and both  
screws. Tighten screws securely.  
6. Reinstall muffler cover and 2 screws.  
Tighten securely.  
intermittent position. If your engine will not run  
properly or you require further assistance,  
contact an authorized service dealer or call  
1--800--554--6723.  
STORAGE  
Fuel stabilizer is an acceptable alternative in  
minimizing the formation of fuel gum deposits  
during storage. Add stabilizer to gasoline in fuel  
tank or fuel storage container. Follow the mix  
instructions found on stabilizer container. Run  
engine at least 5 minutes after adding stabilizer.  
WARNING: Perform the following  
steps after each use:  
S Allow engine to cool, and secure the unit  
before storing or transporting.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
S Store unit and fuel well out of the reach of  
children.  
SEASONAL STORAGE  
Prepare unit for storage at end of season or if  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Clean the entire unit before lengthy stor-  
age.  
S Store in a clean dry area.  
S Lightly oil external metal surfaces.  
FUEL SYSTEM  
Under FUELING ENGINE in the OPERA-  
TION section of this manual, see message la-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine.  
ENGINE  
S Remove spark plug and pour 1 teaspoon of  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range.  
S Clean air filter.  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
S At the beginning of the next season, use  
only fresh fuel having the proper gasoline to  
oil ratio.  
OTHER  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts to rust.  
-- 9 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing any of the  
recommended remedies below other than remedies that require operation of the unit.  
TROUBLE  
Engine will not  
start.  
CAUSE  
1. Engine flooded.  
REMEDY  
1. See “Starting a Flooded Engine”  
in Operation section.  
2. Fill tank with correct fuel mixture.  
3. Install new spark plug.  
2. Fuel tank empty.  
3. Spark plug not firing.  
4. Fuel not reaching  
carburetor.  
4. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
5. Contact an authorized service dealer.  
5. Compression low.  
1. Fuel not reaching  
carburetor.  
1. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
Engine will not  
idle properly.  
2. Carburetor requires  
adjustment.  
3. Crankshaft seals worn.  
4. Compression low.  
2. Contact an authorized service dealer.  
3. Contact an authorized service dealer  
4. Contact an authorized service dealer.  
1. Clean or replace air filter.  
2. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
1. Air filter dirty.  
2. Fuel not reaching  
carburetor.  
Engine will not  
accelerate,  
lacks power, or  
dies under a  
load.  
3. Clean or replace spark plug  
and re-gap.  
3. Spark plug fouled.  
4. Contact an authorized service dealer.  
4. Carburetor requires  
adjustment.  
5. Carbon build up.  
6. Compression low.  
5. Contact an authorized service dealer.  
6. Contact an authorized service dealer.  
1. Choke partially on.  
1. Adjust choke.  
Engine smokes  
excessively.  
2. Fuel mixture incorrect.  
2. Empty fuel tank and refill with  
correct fuel mixture.  
3. Air filter dirty.  
4. Carburetor requires  
adjustment.  
3. Clean or replace air filter.  
4. Contact an authorized service dealer.  
Engine runs hot.  
1. See “Fueling Engine” in Operation  
section.  
1. Fuel mixture incorrect.  
2. Replace with correct spark plug.  
3. Contact an authorized service dealer.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Contact an authorized service dealer.  
4. Carbon build up.  
-- 1 0 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, INC.,  
cover predelivery setup or normal adjustments  
warrants to the original purchaser that each explained in the instruction manual.  
new Poulan PROr brand gasoline tool or at-  
tachment is free from defects in material and  
workmanship and agrees to repair or replace  
under this warranty any defective gasoline  
product or attachment as follows from the  
original date of purchase:  
2 YEARS -- Parts and Labor, when used for  
household purposes.  
90 DAYS -- Parts and Labor, when used for  
commercial, professional, or income producing  
purposes.  
30 DAYS -- Parts and Labor, if used for rental RANTY LASTS OR THE EXCLUSION OR  
purposes.  
This warranty is not transferable and does not  
cover damage or liability caused by improper  
handling, improper maintenance, or the use of  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE  
LIMITATIONS OR EXCLUSION MAY NOT  
APPLY TO YOU.  
accessories and/or attachments not specifically The policy of ELECTROLUX HOME PROD-  
recommended by ELECTROLUX HOME  
UCTS, INC., is to continuously improve its  
PRODUCTS, INC., for this tool. Additionally, products. Therefore, ELECTROLUX HOME  
this warranty does not cover tune-ups, spark  
PRODUCTS, INC., reserves the right to  
plugs, filters, starter ropes, starter springs, cut- change, modify, or discontinue models, de-  
ting line, or rotating head parts that will wear and signs, specifications, and accessories of all  
require replacement with reasonable use during products at any time without notice or obliga-  
the warranty period. This warranty does not tion to any purchaser.  
U.S. EPA/CALIFORNIA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OBLIGA-  
road engine, but ELECTROLUX HOME  
TIONS: The U.S. Environmental Protection PRODUCTS, INC., cannot deny warranty sole-  
Agency/California Air Resources Board and ly for the lack of receipts or for your failure to en-  
ELECTROLUX HOME PRODUCTS, INC., are  
sure the performance of all scheduled mainte-  
pleased to explain the emissions control system nance. As the small off--road engine engine  
warranty on your year 2002--2004 small off-- owner, you should be aware that ELECTRO-  
road engine. In California, all small off--road en- LUX HOME PRODUCTS, INC., may deny you  
gines must be designed, built, and equipped to warranty coverage if your small off--road engine  
meet the State’s stringent anti--smog standards. engine or a part of it has failed due to abuse, ne-  
ELECTROLUX HOME PRODUCTS, INC.,  
glect, improper maintenance, unapproved mod-  
must warrant the emission control system on ifications, or the use of parts not made or ap-  
your small off--road engine for the periods of proved by the original equipment manufacturer.  
time listed below provided there has been no You are responsible for presenting your small  
abuse, neglect, or improper maintenance of off--road engine to an ELECTROLUX HOME  
your small off--road engine. Your emission con- PRODUCTS, INC., authorized repair center as  
trol system includes parts such as the carbure-  
soon as a problem exists. Warranty repairs  
tor and the ignition system. Where a warrant- should be completed in a reasonable amount of  
able condition exists, ELECTROLUX HOME  
PRODUCTS, INC., will repair your small off--  
time, not to exceed 30 days. If you have any  
questions regarding your warranty rights and re-  
road engine engine at no cost to you. Expenses sponsibilities, you should contact your nearest  
covered under warranty include diagnosis, authorized service center or call ELECTRO-  
parts and labor. MANUFACTURER’S WAR-  
RANTY COVERAGE: If any emissions related  
LUX HOME PRODUCTS, INC., at  
1--800--554--6723.  
WARRANTY COM-  
part on your engine (as listed under Emissions MENCEMENT DATE: The warranty period be-  
Control Warranty Parts List) is defective or a de- gins on the date the small off--road engine is  
fect in the materials or workmanship of the en- purchased. LENGTH OF COVERAGE: This  
gine causes the failure of such an emission re- warranty shall be for a period of two years from  
lated part, the part will be repaired or replaced the initial date of purchase. WHAT IS COV-  
by ELECTROLUX HOME PRODUCTS, INC.  
OWNER’S WARRANTY RESPONSIBILI-  
ERED: REPAIR OR REPLACEMENT OF  
PARTS. Repair or replacement of any war-  
TIES: As the small off--road engine engine own- ranted part will be performed at no charge to the  
er, you are responsible for the performance of owner at an approved ELECTROLUX HOME  
the required maintenance listed in your instruc- PRODUCTS, INC., servicing center. If you  
tion manual. ELECTROLUX HOME PROD-  
have any questions regarding your warranty  
UCTS, INC., recommends that you retain all re- rights and responsibilities, you should contact  
ceipts covering maintenance on your small off-- your nearest authorized service center or call  
-- 11 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTROLUX HOME PRODUCTS, INC., at  
1--800--554--6723 WARRANTY PERIOD: Any  
warranted part which is not scheduled for re-  
placement as required maintenance, or which is  
scheduled only for regular inspection to the ef-  
fect of “repair or replace as necessary” shall be  
warranted for 2 years. Any warranted part which  
is scheduled for replacement as required main-  
tenance shall be warranted for the period of time  
up to the first scheduled replacement point for  
that part. DIAGNOSIS: The owner shall not be  
charged for diagnostic labor which leads to the  
determination that a warranted part is defective  
if the diagnostic work is performed at an ap-  
proved ELECTROLUX HOME PRODUCTS,  
INC., servicing center. CONSEQUENTIAL  
DAMAGES: ELECTROLUX HOME PROD-  
UCTS, INC., may be liable for damages to other  
engine components caused by the failure of a  
warranted part still under warranty. WHAT IS  
NOT COVERED: All failures caused by abuse,  
neglect, or improper maintenance are not cov-  
ered. ADD--ON OR MODIFIED PARTS: The  
use of add--on or modified parts can be grounds  
for disallowing a warranty claim. ELECTRO-  
LUX HOME PRODUCTS, INC., is not liable to  
cover failures of warranted parts caused by the  
use of add--on or modified parts. HOW TO FILE  
A CLAIM: If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized service  
center or call ELECTROLUX HOME PROD-  
UCTS, INC., at 1--800--554--6723. WHERE TO  
GET WARRANTY SERVICE: Warranty ser-  
vices or repairs shall be provided at all ELEC-  
TROLUX HOME PRODUCTS, INC., service  
centers. Call: 1--800--554--6723 MAINTE-  
NANCE, REPLACEMENT AND REPAIR OF  
EMISSION RELATED PARTS: Any ELEC-  
TROLUX HOME PRODUCTS, INC., approved  
replacement part used in the performance of  
any warranty maintenance or repair on emis-  
sion related parts will be provided without  
charge to the owner if the part is under warranty.  
EMISSION CONTROL WARRANTY PARTS  
LIST: Carburetor, Ignition System: Spark Plug  
(covered up to maintenance schedule), Ignition  
Module, Muffler including catalyst. MAINTE-  
NANCE STATEMENT: The owner is responsi-  
ble for the performance of all required mainte-  
nance as defined in the instruction manual.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
-- 1 2 --  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Phase Technology Speaker CI 60 IX QM User Manual
Philips Headphones SWB9000 27 User Manual
Philips Mouse SPM1500 User Manual
Philips Pole Saw 512 MT User Manual
Pioneer DVD Player BDP 05FD User Manual
Pioneer Stereo Receiver VSX 916 S User Manual
Poulan Snow Blower 421918 User Manual
Precor Treadmill 941si User Manual
PYLE Audio Car Video System PLD58MUT User Manual
PYLE Audio DJ Equipment PWMA 120 User Manual