e-Manual
Philips LCD Monitor Electronic User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/INDEX.HTM [98-07-30 15:20]
Safety and Troubleshooting Information
●
●
Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or
extreme cold.
In order to maintain the best performance of your monitor and use it for a longer lifetime,
please use the monitor in a location that falls within the following temperature and
humidity ranges.
ꢀ❍
Temperature: 0-40°C 32-95°F
Humidity: 20-80% RH
ꢀ❍
●
IMPORTANT: Always activate a moving screen saver program when you leave your
monitor unattended. Always activate a periodic screen refresh application if your LCD
monitor will display unchanging static content. Uninterrupted display of still or static
images over an extended period may cause “burn in”, also known as “after-imaging” or
“ghost imaging”, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-
known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-
imaging” or “ghost imaging” will disappear gradually over a period of time after the power
has been switched off.
WARNING: Severe” burn-in” or “after-image” or “ghost image” symptoms will not
disappear and cannot be repaired. The damage mentioned above is not covered under
your warranty.
Service:
●
●
The casing cover should be opened only by qualified service personnel.
If there is any need for any document for repair or integration, please contact with your
local service center. (please refer to the chapter of "Consumer Information Center")
●
●
For transportation information, please refer to "Physical Specifications".
Do not leave your monitor in a car/trunk under direct sun light.
Consult a service technician if the monitor does not operate normally, or you are
not sure what procedure to take when the operating instructions given in this
manual have been followed.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/safety.htm 第 2 頁 / 共 2 [98-07-30 15:20]
FAQs (Frequently Asked Questions)
ꢀ
FAQs (Frequently Asked Questions)
ꢀ
ꢀ
General FAQs
ꢀ
Q1: When I install my monitor what should I do if the screen shows 'Cannot display this
video mode'?
ꢀ
ꢀ
A: Recommended resolution for Philips 21.5": 1920x1080 @60Hz.
ꢀ
1. Unplug all cables, then connect your PC to the monitor that you used
previously.
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel
Window, select the Display icon. Inside the Display Control Panel, select the
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the
slidebar to 1920x1080 pixels (21.5").
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at
1920x1080@60Hz (21.5").
5. Shut down your computer, disconnect your old monitor and reconnect your
Philips LCD monitor.
6. Turn on your monitor and then turn on your PC.
Q2: What does the recommended refresh rate for LCD monitor?
A:Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance
on screen, you can set it up to 75Hz to see if that removes the disturbance.
Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .
icm)?
A: These are the driver files for your monitor. Follow the instructions in your user
manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .
icm files) or a driver disk when you first install your monitor. Follow the instructions to
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .
icm files) will be installed automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_faq.htm 第 1 頁 / 共 5 [98-07-30 15:20]
FAQs (Frequently Asked Questions)
Q4: How do I adjust the resolution?
A: Your video card/graphic driver and monitor together determine the available
resolutions. You can select the desired resolution under Windows® Control Panel
with the "Display properties".
Q5: What if I get lost when I am making monitor adjustments?
A: Simply press the OK button, then select 'Reset' to recall all of the original factory
settings.
Q6: Will the LCD screen be resistant to scratches?
A: In general it is recommended that the panel surface is not subjected to excessive
shocks and is protected from sharp or blunt objects. When handling the monitor,
make sure that there is no pressure or force applied to the panel surface side. This
may affect your warranty conditions.
Q7: How should I clean the LCD surface?
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use
isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,
hexane, etc.
Q8:Can I change the color setting of my monitor?
A:Yes, you can change your color setting through OSD control as the following
procedures,
1. Press "OK" to show the OSD (On Screen Display) menu
2. Press "Down Arrow" to select the option "Color" then press "OK" to enter color
setting, there are three settings as below.
a. Color Temperature; The six settings are 5000K, 6500K, 7500K, 8200K,
9300K and 11500K. With settings in the 5000K range the panel appears
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_faq.htm 第 2 頁 / 共 5 [98-07-30 15:20]
FAQs (Frequently Asked Questions)
‘warm,' with a red-white color tone, while a 11500K temperature yields ‘cool,
blue-white toning."
b. sRGB; this is a standard setting for ensuring correct exchange of colors
between different device (e.g. digital cameras, monitors, printers, scanners,
etc)
c. User Define; the user can choose his/her preference color setting by
adjusting red, green blue color.
*A measurement of the color of light radiated by an object while it is being heated.
This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower
Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are
blue. Neutral temperature is white, at 6504K.
Q9: Can the Philips LCD Monitor be mounted on the wall?
A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount
holes on the rear cover allows the user to mount the Philips monitor on most of the
VESA standard arms or accessories. We recommend to contact your Philips sales
representative for more information.
Compatibility with other Peripherals
Q10: Can I connect my LCD monitor to any PC, workstation or Mac?
A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and
workstations. You may need a cable adapter to connect the monitor to your Mac
system. Please contact your Philips sales representative for more information.
Q11: Are Philips LCD monitors Plug-and-Play?
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP,
Vista and Linux.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_faq.htm 第 3 頁 / 共 5 [98-07-30 15:20]
FAQs (Frequently Asked Questions)
LCD Panel Technology
Q12: What kind of wide-angle technology is available?
A: Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA, or
PVA technologies. TN panels have improved over the years, but still cannot match
the Contrast Ratio offered by IPS panel.
Ergonomics, Ecology and Safety Standards
Q13: What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD
panels?
A: Uninterrupted display of still or static images over an extended period may cause
"burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in",
"after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel
technology. In most cases, the "burned in" or "atter-imaging" or "ghost imaging" will
disappear gradually over a period of time after the power has been switched off.
Always activate a moving screen saver program when you leave your monitor
unattended.
Always activate a periodic screen refresh application if your LCD monitor will display
unchanging static content.
WARNING: Severe"burn-in" or "after-image" or "ghost image" symptoms will not
disappear and cannot be repaired. The damage mentioned above is not covered
under your warranty.
Q14: Why is my Display not showing sharp text, and is displaying jagged characters?
A: Your LCD monitor works best at its native resolution of 1920x1080@60Hz. For
best display please use this resolution.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_faq.htm 第 4 頁 / 共 5 [98-07-30 15:20]
FAQs (Frequently Asked Questions)
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_faq.htm 第 5 頁 / 共 5 [98-07-30 15:20]
Troubleshooting
Troubleshooting
ꢀ
ꢀ
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these
solutions, contact Philips customer service representative.
ꢀ
ꢀ
Common Problems
ꢀ
Having this problem
Check these items
●
Make sure the power cord is plugged into the power outlet
and into the back of the monitor.
First, ensure that the power button on the front of the monitor
No Picture
(Power LED not lit)
●
is in the OFF position, then press it to the ON position.
●
●
Make sure the computer is turned on.
Make sure the signal cable is properly connected to your
computer.
No Picture
●
●
make sure the monitor cable has no bent pins on the connect
(Power LED is white blinking)
side. If yes, repair or replace the cable.
The Energy Saving feature may be activated
Screen says
●
Make sure the monitor cable is properly connected to your
computer. (Also refer to the Quick Set-Up Guide).
Check to see if the monitor cable has bent pins.
●
●
Make sure the computer is turned on.
●
The auto function is applicable only in VGA-Analog mode. If
the result is not satisfactory, you can do manual adjustments
via the OSD menu. Note that the Auto Function is not
applicable in DVI-Digital mode as it is not necessary.
AUTO button doesn't function in VGA
mode
Imaging Problems
●
●
Press the Auto button.
Adjust the image position using the Phase/Clock of Setup in
Image is not centered
OSD Main Controls.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_troub.htm 第 1 頁 / 共 3 [98-07-30 15:20]
Troubleshooting
●
Check that the signal cable is properly securely connected to
the graphics board or PC.
Image vibrates on the screen
Vertical flicker appears
●
●
Press the Auto button.
Eliminate the vertical bars using the Phase/Clock of Setup in
OSD Main Controls.
Horizontal flicker appears
●
●
Press the Auto button.
Eliminate the vertical bars using the Phase/Clock of Setup in
OSD Main Controls.
●
●
Adjust the contrast and brightness on On-Screen Display.
image appears blurred, indistinct or too
dark
Uninterrupted display of still or static images over an
extended period may cause " burn in", also known as "after-
imaging " or "ghost imaging", on your screen. "Burn-in", "after-
imaging", or "ghost imaging" is a well-known phenomenon in
LCD panel technology. In most cases, the "burned in" or
"after-imaging" or "ghost imaging" will disappear gradually
over a period of time after the power has been switched off.
Always activate a moving screen saver program when you
leave your monitor unattended.
An "after-image", "burn-in" or "ghost
image" remains after the power has
been turned off.
●
●
Always activate a periodic screen refresh application if your
LCD monitor will display unchanging static content.
●
●
Set the PC’s display resolution to the same mode as
monitor’s recommended screen native resolution.
Image appears distorted. Text is fuzzy
or blurred.
The remaining dots are normal characteristic of the liquid
Green, red, blue, dark, and white dots
appears on the screen
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_troub.htm 第 2 頁 / 共 3 [98-07-30 15:20]
Troubleshooting
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service
representative.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/safety/saf_troub.htm 第 3 頁 / 共 3 [98-07-30 15:20]
Regulatory Information
ꢀ
Regulatory Information
ꢀ
Available for selective models
ꢀ
ꢀ
TCO Displays 5.0 Information
ꢀ
ꢀ
Congratulations,
Your display is designed for both you and the planet!
ꢀ
This display carries the TCO Certified label. This ensures that the display is designed for minimal
impact on the climate and natural environment, while offering all the performance expected from top
of the line electronic products. TCO Certified is a third party verified program, where every product
model is tested by an accredited independent test laboratory. TCO Certified represents one of the
toughest certifications for displays worldwide.
ꢀ
ꢀ
ꢀ
Some of the Usability features of the TCO Displays 5.0 requirements:
ꢀ
Visual Ergonomics
ꢀ
Good visual ergonomics in order to improve the working environment for the user and to reduce sight and strain problems.
Important parameters are:
ꢀ
ꢀ
●
●
●
Light levels without color tint, Uniform color and luminance, Wide color gamut
Calibrated color temperature and gamma curve
Wide luminance level, Dark black levels, Low motion blur
ꢀ
ꢀ
ꢀ
Electrical Safety
ꢀ
●
Product fulfills rigorous safety standards
Emissions
●
●
Low alternating electric and magnetic fields emissions
Low acoustic noise emissions
Some of the Environmental features of the TCO Displays 5.0 requirements:
●
The brand owner demonstrates corporate social responsibility and has a certified environmental management system (EMAS or
ISO 14001)
●
●
●
●
●
Very low energy consumption both in on- and standby mode
Restrictions on chlorinated and brominated flame retardants, plasticizer and polymers
Restrictions on heavy metals such as cadmium, mercury and lead (RoHS compliance)
Both product and product packaging is prepared for recycling
The brand owner offers take-back options
The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users
as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of
IT equipment in a more user-friendly direction. Our labeling system started with displays in 1992 and is now requested by users and
IT-manufacturers all over the world.
For more information, please visit www.tcodevelopment.com
For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c1o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
reflections from surrounding light and bright surfaces.
Recycling Information for Customers
There is currently a system of recycling up and running in the European countries, such as The Netherlands,
Belgium, Norway, Sweden and Denmark.
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to follow the
IT product recycling management process, detail can be found in web site www.epa.gov.tw
The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is recycled at
the end of its life cycle.
For help and service, please contact Consumers Information Center or F1rst Choice Contact Information Center in
each country.
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/
EC governing used electrical and electronic appliances, this product may not be disposed of with normal household
waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic
equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your
local government office, the waste disposal organization that serves your household or the store at which you purchased
the product.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and
Federal laws. For the disposal or recyciing information, contact www.mygreenelectronics.com or www.eiae.org.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c2o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
EPEAT
“The EPEAT (Electronic Product Environmental Assessment Tool) program evaluates computer desktops, laptops,
and monitors based on 51 environmental criteria developed through an extensive stakeholder consensus process
supported by US EPA.
EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop
computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and consistent
set of performance criteria for the design of products, and provides an opportunity for manufacturers to secure
market recognition for efforts to reduce the environmental impact of its products.”
Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste EPEAT’S requirement that all registered products meet ENERGY STAR’s
energy efficiency specifications, means that these products will consume less energy throughout their life.
ROHS is a European Directive aiming to control the use of certain hazardous substances in the production of new
electrical and electronic equipment. Philips has completely eliminated four of six RoHS-banned substances form its
products by 1998-eight full years before compliance was required and has lowered usage of the remaining
substances significantly below the mandated levels.
CE Declaration of Conformity
This product is in conformity with the following standards
- EN60950-1:2001 (Safety requirement of Information Technology Equipment)
- EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)
- EN55024:1998 (Immunity requirement of Information Technology Equipment)
- EN61000-3-2:2006 (Limits for Harmonic Current Emission)
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
- 2006/95/EC (Low Voltage Directive)
- 2004/108/EC (EMC Directive)
and is produced by a manufacturing organization on ISO9000 level.
The product also comply with the following standards
- ISO13406-2 (Ergonomic requirement for Flat Panel Display)
- GS EK1-2000 (GS specification)
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)
- TCO'03, TCO Displays 5.0 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission,
TCO: Swedish Confederation of Professional Employees) for TCO versions
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c3o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
Energy Star Declaration
This monitor is equipped with a function for saving energy which supports the VESA Display
Power Management Signaling (DPMS) standard. This means that the monitor must be
connected to a computer which supports VESA DPMS. Time settings are adjusted from the
system unit by software.
VESA State
ON (Active)
LED Indicator
White
Power Consumption
Normal operation
< 28 W (typ.)
Power Saving
Alternative 2
One step
Sleep
White Blinking
Off
< 0.8 W (typ.)
< 0.5 W (typ.)
Switch Off
®
As an ENERGY STAR Partner, we have determined that this product meets the
®
ENERGY STAR guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for a long time.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
●
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c4o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
FCC Declaration of Conformity
Declaration of Conformity for Products Marked with FCC Logo,
United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur
pourrait essayer de corriger la situation en prenant les mesures suivantes:
●
●
●
●
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et le récepteur.
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR
LE MATERIEL BROUILLEUR DU CANADA.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c5o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
EN 55022 Compliance (Czech Republic Only)
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment
that works together (computer, monitor, printer, and so on) should have the same power supply source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form
of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket,
which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards
PN-93/T-42107 and PN-89/E-06251.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c6o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c7o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch
Röntgenstrahlen" festgelegten Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da
die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
End-of-Life Disposal
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product
to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your sales representative.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
China RoHS
The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by
Electronic Information Products" or commonly referred to as China RoHS. All products including CRT and LCD monitor
which are produced and sold for China market have to meet China RoHS request.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c8o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
环保使用期限
此标识指期限(十年),电子信息产品
中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突变, 电子信息
产品用户使用该电子信息产品不会对环境造成严重 污染或对其人身、 财产造成严重 损害的期限．
Lead-free Product
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSHd/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c9o頁m/ 共. A10ll [M98a-0n7-u30a1ls5:2S0]earch And Download.
Regulatory Information
Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic
equipment. Toxic substances like Lead has been eliminated and compliance with European community’s
stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment
have been adhered to in order to make Philips monitors safe to use throughout its life cycle.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5...N01.001/CD-Contents/lcd/manDuaol/EwNnGlLoIaSdH/2f2ro3Em1/sWafewtyw/re.gSs/oremgualant.hutaml第s.c10o頁m/.共A1ll0Manuals Search And Download.
[98-07-30 15:20]
About This Manual
ꢀ
ꢀ
About This Manual
About This Guide
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It
describes the LCD monitor's features, setup, operation and other important information. Its
contents are identical to the information in our printed version.
It includes the following sections:
●
Safety and Troubleshooting Information provides tips and solutions for common problems
as well as other related information you may need.
●
●
About This Electronic User's Manual gives an overview of information included, along with
notation icon descriptions and other documentation for your reference.
Product Information gives an overview of the monitor's features as well as the technical
specifications for this monitor.
●
Installing Your Monitor describes the initial setup process and gives an overview of how to
use the monitor.
●
●
On-Screen Display provides information on adjusting the settings on your monitor.
Customer Care and Warranty contains a list of worldwide Philips Consumer Information
Centers along with help desk phone numbers and information on the warranty applicable
to your product.
●
●
Glossary defines technical terms.
Download and Print Option transfers this entire manual to your hard drive for easy
reference.
Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions and Warnings
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/about/about.htm 第 1 頁 / 共 2 [98-07-30 15:20]
About This Manual
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic
type. These blocks contain notes, cautions or warnings. They are used as follows:
NOTE: This icon indicates important information and tips that help you make
better use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.
Some warnings may appear in alternate formats and may not be accompanied by an icon. In
such cases, the specific presentation of the warning is mandated by the relevant regulatory
authority.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/about/about.htm 第 2 頁 / 共 2 [98-07-30 15:20]
Product Information
ꢀ
Product Information
Your LCD monitor
ꢀ
ꢀ
ꢀ
ꢀ
Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register
your product at. www.philips.com/welcome
ꢀ
ꢀ
ꢀ
SmartContrast
What is it?
ꢀ
ꢀ
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast
ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter
images or dimming backlighting for clear display of images on dark backgrounds.
Why do I need it?
You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically controls
contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text for
office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of your
monitor.
How does it work?
When you active SmartContrast which will analysis the content you are displaying in real time to adjust colors and
control backlight intensity. This function can obviously enhance contrast in dynamic for more entertainment fun when
viewing videos or playing games.
SmartSaturate
What is it?
Smart technology that controls color saturation - the degree to which one on screen color is diluted by neighboring
colors - to deliver rich and vibrant images for more entertainment fun when you are viewing videos.
Why do I need it?
You want rich, vibrant images for more entertainment fun when viewing photos or videos.
How does it work?
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 1 頁 / 共 7 [98-08-06 09:06]
Product Information
SmartSaturate dynamically controls color saturation - the degree to which on-screen color is diluted by neighboring
colors - to deliver rich, vibrant display for more entertainment fun when you are viewing images or videos in your
display's Entertainment mode and is turned off for top quality display of office application and in the Economy mode to
reduce power consumption.
SmartSharpness
What is it?
Smart technology that enhances sharpness when you need it for ultimate display performance and more entertainment
fun when you are viewing videos or photos.
Why do I need it?
You want the ultimate in sharpness for more entertainment fun when viewing photos or videos.
How does it work?
Smart technology enhances sharpness when you need it for ultimate display performance and more entertainment fun
when you are viewing videos or photos in the Entertainment mode and is turned off for top quality display of office
applications and in the Economy mode to reduce power consumptions.
Technical Specifications*
Picture/Display
TFT-LCD
21.5'' W
ꢀ LCD panel type
ꢀ Panel size
16:9
ꢀ Aspect ratio
ꢀ Pixel Pitch
0.248 x 0.248 mm
ꢀ Brightness
250 cd/m²
25000:1
ꢀ SmartContrast
1000:1
ꢀ Contrast ratio(typ.)
ꢀ Response time (typical)
ꢀ Optimum Resolution
ꢀ Viewing angle
5 ms
1920 x 1080 @ 60Hz
178° (H) / 170° (V) @ C/R > 5
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 2 頁 / 共 7 [98-08-06 09:06]
Product Information
N/A
ꢀ Picture Enhancement
ꢀ Display colors
ꢀ Vertical refresh rate
ꢀ Horizontal Frequency
ꢀ sRGB
16.7 M
56Hz -76Hz
30kHz - 83kHz
YES
Connectivity
ꢀ Signal input
DVI-D (digital, HDCP) (available for selective models), VGA (Analog)
Separate Sync, Sync on Green
ꢀ Input Signal
Convenience
Auto, 4:3/Wide (Back), Input (Down), Brightness (UP) Menu (OK), Power
On/Off
ꢀ User Convenience
English, French, German, Italian, Russian, Spanish, Simplified Chinese,
Portuguese, Turkish
ꢀ OSD Languages
VESA mount (100 x 100mm), Kensington lock
ꢀ Other convenience
ꢀ Plug & Play Compatibility
Stand
DDC/CI, sRGB, Windows 98/2000/XP/Vista, Mac OS X
-5/+20
ꢀ Tilt
Power
< 33 W (typ.)
ꢀ On mode
AC Input Voltage at
100VAC +/-5VAC,
50Hz +/- 3Hz
AC Input Voltage at
115VAC +/-5VAC,
60Hz +/- 3Hz
AC Input Voltage at
230VAC +/-5VAC, 50Hz
+/ -3Hz
Energy Consumption
Normal Operation (typcial)
28 W
0.8 W
0.5 W
28 W
0.8 W
0.5 W
28 W
0.8 W
0.5 W
Sleep
Off
AC Input Voltage at
100VAC +/-5VAC,
50Hz +/ -3Hz
AC Input Voltage at
115VAC +/-5VAC,
60Hz +/ -3Hz
AC Input Voltage at
230VAC +/-5VAC, 50Hz
+/ -3Hz
Heat Dissipation*
Normal Operation
Sleep
95.56BTU/hr
2.73BTU/hr
1.7BTU/hr
95.56BTU/hr
2.73BTU/hr
1.7BTU/hr
95.56BTU/hr
2.73BTU/hr
1.7BTU/hr
Off
On mode: White, Standby/Sleep mode: White (blinking)
Build-in, 100-240VAC, 50/60Hz
ꢀ Power LED indicator
ꢀ Power Supply
Dimension
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 3 頁 / 共 7 [98-08-06 09:06]
Product Information
ꢀ Product with stand ( WxHxD)
517 x 398 x 200mm
517 x 312 x 61mm
582 x 452 x 140mm
ꢀ Product without stand
( WxHxD)
ꢀ Box dimension ( WxHxD)
Weight
4.03kg
3.70kg
5.23kg
ꢀ Product with stand
ꢀ Product without stand
ꢀ Product with packaging
Operating Condition
0° C to 40 ° C
-20° C to 60° C
ꢀ Temperature range (operation)
ꢀ Temperature range (operation)
20% to 80%
ꢀ Relative humidity
Non-operation: + 12,000 ft ( 3,658 m)
operation: + 40,000 ft ( 12,192 m),
50000 hrs
ꢀ Altitude
ꢀ MTBF
Environmental
ꢀ ROHS
YES
sliver
ꢀ EPEAT
5.0
ꢀ EnergyStar
ꢀ Packaging
100% recyclable
Compliance and standards
CE Mark, Energy Star 5.0, FCC Class B, TCO5.0, UL/cUL
ꢀ Regulatory Approvals
Cabinet
ꢀ Color
Black/Black
Glossy
ꢀ Finish
* This data is subject to change without notice.
Resolution & Preset Modes
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 4 頁 / 共 7 [98-08-06 09:06]
Product Information
A.
-
Maximum Resolution
For 223E1
1920 x 1080 at 60 Hz (analog input)
1920 x 1080 at 60 Hz (digital input)*
*available for selective models
B. Recommended Resolution
-
For 223E1
1920 x 1080 at 60 Hz (digital input)*
*available for selective models
12 factory preset modes:
H. freq (kHz)
31.47
31.47
37.50
37.88
46.88
48.36
60.02
44.77
49.70
63.98
79.98
67.50
Resolution
720*400
V. freq (Hz)
70.09
59.94
75.00
60.32
75.00
60.00
75.03
59.86
59.81
60.02
75.03
60.00
640*480
640*480
800*600
800*600
1024*768
1024*768
1280*720
1280*800
1280*1024
1280*1024
1920*1080
Automatic Power Saving
If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce
its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the
monitor will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic
power saving feature:
Power Management Definition
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 5 頁 / 共 7 [98-08-06 09:06]
Product Information
LED
color
VESA Mode
Active
Video
H-sync
Yes
V-sync
Yes
Power Used
< 33 W (typ.)
ON
White
White
Sleep
OFF
No
-
No
-
< 0.8 W (typ.)
< 0.5 W (typ.)
(Blinking)
Switch Off
OFF
Off
®
®
This monitor is ENERGY STAR compliant. As an ENERGY STAR Partner, we have determined that
®
this product meets the ENERGY STAR guidelines for energy efficiency.
* This data is subject to change without notice.
The native resolution of the monitor is 1920 x 1080. By default, your monitor has 100% (max.) 50% contrast, and
6500K color temperature, with full white pattern.
Product Views
Follow the links to see various views of the monitor and its components.
Physical Function
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 6 頁 / 共 7 [98-08-06 09:06]
Product Information
Tilt
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-ED...N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/PRODUCT/PRODUCT.HTM 第 7 頁 / 共 7 [98-08-06 09:06]
Philips Pixel Defect Policy
Philips Pixel Defect Policy
ꢀ
ꢀ
Philips' Flat Panel Monitors Pixel Defect Policy
ꢀ
Philips strives to deliver the highest quality products. We use some of the industry's most advanced
manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on
the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with
an unacceptable number of defects will be repaired or replaced under warranty. This notice explains
the different types of pixel defects and defines acceptable defect levels for each type. In order to
qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel
must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19"
XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain
types or combinations of pixel defects that are more noticeable than others. This policy is valid
worldwide.
ꢀ
ꢀ
ꢀ
ꢀ
Pixels and Sub pixels
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub
pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together
appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of
other colors.
Types of Pixel Defects
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel
defects and several types of sub pixel defects within each category.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/product/pixel.htm 第 1 頁 / 共 4 [98-07-30 15:21]
Philips Pixel Defect Policy
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is,
a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern.
There are the types of bright dot defects:
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
One lit red, green or blue sub
pixel
Three adjacent lit sub pixels
(one white pixel)
- Green + Blue = Cyan (Light Blue)
A red or blue bright dot must be more than 50 percent brighter than neighboring dots
while a green bright dot is 30 percent brighter than neighboring dots.
Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That
is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern.
These are the types of black dot defects:
One dark sub pixel
Two or three adjacent dark sub pixels
Proximity of Pixel Defects
Because pixel and sub pixels defects of the same type that are near to one another may be more
noticeable, Philips also specifies tolerances for the proximity of pixel defects.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/product/pixel.htm 第 2 頁 / 共 4 [98-07-30 15:21]
Philips Pixel Defect Policy
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT
LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the
tolerances listed in the following tables.
BRIGHT DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
223E1
1 lit subpixel
3
2 adjacent lit subpixels
1
3 adjacent lit subpixels (one white pixel)
Distance between two bright dot defects*
Total bright dot defects of all types
0
>15mm
3
BLACK DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
223E1
1 dark subpixel
5 or fewer
2 or fewer
0
2 adjacent dark subpixels
3 adjacent dark subpixels
Distance between two black dot defects*
Total black dot defects of all types
>15mm
5 or fewer
TOTAL DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
223E1
Total bright or black dot defects of all types
5 or fewer
Note:
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/product/pixel.htm 第 3 頁 / 共 4 [98-07-30 15:21]
Philips Pixel Defect Policy
* 1 or 2 adjacent sub pixel defects = 1 dot defect
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/product/pixel.htm 第 4 頁 / 共 4 [98-07-30 15:21]
Installing Your LCD Monitor
Installing Your LCD Monitor
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Front View Product Description
1
To switch monitor's power On and Off
2
3
To access the OSD menu
To adjust the OSD menu
4
5
6
To adjust brightness of the display
To change the signal input source
Change to 4:3 display / Return to previous OSD level
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/install.htm 第 1 頁 / 共 3 [98-07-30 15:21]
Installing Your LCD Monitor
Automatically adjust the horizontal position, vertical position, phase and
clock settings
7
Rear View
1
2
3
4
VGA input
DVI-D input (available for selective models)
AC power input
Kensington anti-thief lock
Optimizing Performance
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/install.htm 第 2 頁 / 共 3 [98-07-30 15:21]
Installing Your LCD Monitor
●
For best performance, ensure that your display settings are set at 1920x1080, 60Hz.
Note: You can check the current display settings by pressing the 'OK' button
once. The current display mode is shown in OSD main controls called
RESOLUTION.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/install.htm 第 3 頁 / 共 3 [98-07-30 15:21]
Connecting to Your PC
ꢀ
Connecting to Your PC
ꢀ
ꢀ
Accessory Pack
ꢀ
Unpack all the parts.
ꢀ
ꢀ
DVI cable (Optional)
Power cord
EDFU pack
VGA cable (Optional)
Connecting to Your PC
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/connect.htm 第 1 頁 / 共 3 [98-07-30 15:21]
Connecting to Your PC
1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected
VGA cable for the first installation.
*available for selective models
*available for selective models
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/connect.htm 第 2 頁 / 共 3 [98-07-30 15:21]
Connecting to Your PC
2) Connect to PC
(a)
(b)
Turn off your computer and unplug its power cable.
Connect the monitor signal cable to the video connector on the back of your
computer.
(c)
(d)
Plug the power cord of your computer and your monitor into a nearby outlet.
Turn on your computer and monitor. If the monitor displays an image,
installation is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/connect.htm 第 3 頁 / 共 3 [98-07-30 15:21]
The Base
ꢀ
The Base
ꢀ
ꢀ
Attach the Base Stand
ꢀ
1) Place the monitor face down on a smooth surface taking care to avoid scratching or
damaging the screen.
ꢀ
ꢀ
ꢀ
ꢀ
2) Hold the monitor base with both hands and firmly insert the base stand into the base
column.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/base.htm 第 1 頁 / 共 4 [98-07-30 15:21]
The Base
Detach the Base Stand
Place the monitor face on a safe surface, push down on the release button and pull the base
stand away from the monitor body.
Remove the Base
Condition:
●
for VESA standard mounting applications
Remove the 4 screws covers.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/base.htm 第 2 頁 / 共 4 [98-07-30 15:21]
The Base
Remove the 4 screws and then remove the base from the LCD monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/base.htm 第 3 頁 / 共 4 [98-07-30 15:21]
The Base
Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/base.htm 第 4 頁 / 共 4 [98-07-30 15:21]
Getting Started
Your LCD Monitor :
Getting Started
ꢀ
ꢀ
Getting Started
ꢀ
Use the information file ( .inf) for Windows® 2000/XP/Vista or later
ꢀ
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for
Windows® 2000/XP/Vista. This information file ( .inf) should be installed in order that your
Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 2000/XP/Vista and
the Plug & Play application can be activated. The installation procedure based on Windows®
2000 , XP and Vista is specified as follows.
For Windows® 2000
1. Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps
given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific
driver', then click on 'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
For Windows® XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Select and click on the category 'Printers and Other Hardware'
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/gt_start.htm 第 1 頁 / 共 2 [98-07-30 15:21]
Getting Started
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on
the 'Next' button.
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the
'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the
appropriate drive F: (CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with
Windows® XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties
dialog box.
For Windows® Vista
1. Start Windows® Vista
2. Click the Start button; select and click on 'Control Panel'.
3. Select and click on 'Hardware and Sound'
4. Choose 'Device Manager' and Click on 'Update device drivers'.
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.
6. Click on 'Update Driver Software'.
7. Select 'Browse my computer for driver software'.
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:
(CD-ROM Drive:\\Lcd\PC\drivers\).
9. Click the 'Next' button.
10. Wait few minutes for installing the driver, and then click 'Close' button.
If your Windows® 2000/XP/Vista version is different or you need more detailed installation
information, please refer to your Windows® 2000/XP/Vista user's manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/install/gt_start.htm 第 2 頁 / 共 2 [98-07-30 15:21]
On-Screen Display
On-Screen Display
ꢀ
ꢀ
Description of the On Screen Display
What is the On-Screen Display?
On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust
screen performance or select functions of the monitors directly through an on-screen instruction
window. A user friendly on screen display interface is shown as below :
Basic and simple instruction on the control keys.
In the OSD shown above users can press
the cursor, to confirm the choice or change.
buttons at the front bezel of the monitor to move
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/osd/osddesc.htm 第 1 頁 / 共 3 [98-07-30 15:21]
On-Screen Display
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference
when you want to work your way around the different adjustments later on.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/osd/osddesc.htm 第 2 頁 / 共 3 [98-07-30 15:21]
On-Screen Display
Resolution notification
This monitor is designed for optimal performance at its native resolution, 1920X1080@60Hz. When
the monitor is powered on at a different resolution, an alert is displayed on screen: Use
1920X1080@60Hz for best results.
Display of the native resolution alert can be switched off from Setup in the OSD (On Screen
Display) menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/223E1/osd/osddesc.htm 第 3 頁 / 共 3 [98-07-30 15:21]
Customer Care
arranty
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR
WARRANTY COVERAGE
AFRICA: South Africa
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arranty.htm [98-07-30 15:21]
Your Philips F1rst Choice arranty
Your Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver
high-quality performance, ease of use and ease of installation. Should you
encounter any difficulties while installing or using this product, please contact the
Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site if your monitor
turns out to be faulty or defective. Philips aims at a swap within 48 hours of your
call being received.
What is covered?
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark,
France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the
Netherlands, Norway, Poland, Portugal, Sweden, Switzerland, Spain and the United Kingdom and
only for monitors originally designed, manufactured, approved and/or authorized for usage within
these countries.
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your
monitor will be swapped by at least an equivalent monitor in case of defects provided for under the
warranty coverage.
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap
monitor the warranty period remains equal to that of your original monitor, being 36 months as from
the purchase date of your original monitor.
What is excluded?
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended
use, in accordance with its operating instructions and upon presentation of the original invoice or
cash receipt, indicating the date of purchase, dealer's name and model and production number of
the product.
The Philips F1rst Choice Warranty may not apply if:
●
●
The documents have been altered in any way or made illegible;
The model or production number on the product has been altered, deleted, removed or made
illegible;
●
●
Repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
Damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect;
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_1st.htm 第 1 頁 / 共 3 [98-07-30 15:22]
Your Philips F1rst Choice arranty
●
Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
●
●
Defects caused by abuse or misuse of the monitor;
Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
●
Note that products that are not originally designed, manufactured, approved and/or
authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips
F1rst Choice Warranty. In these cases the Philips global warranty terms are valid.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
Philips helpdesk.
To solve your problem quickly, please prepare the following details before contacting the Philips
helpdesk:
●
●
●
●
Philips type number
Philips serial number
Purchase date (copy of purchase may be required)
PC environment Processor:
ꢀ❍
ꢀ❍
ꢀ❍
CUP and Graphic card name and driver version
Operating system
Application being used
●
Other cards installed
Having the following information available will also help speed up the process:
●
●
Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
The full address to which the faulty monitor has to be collected and the swap model should
be delivered.
Or you can reach us via:
Website: http://www.philips.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_1st.htm 第 2 頁 / 共 3 [98-07-30 15:22]
Your Philips F1rst Choice arranty
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_1st.htm 第 3 頁 / 共 3 [98-07-30 15:22]
F1rst Choice Contact Information
F1rst Choice Contact Information
Country
Code
+43
+32
+45
+358
+33
+49
+30
+353
+39
+352
+31
+47
+48
+351
+34
+46
+41
+44
Telephone number
0810 000206
078 250851
Tariff
Austria
€ 0.07
Belgium
Denmark
Finland
€ 0.06
3525 8761
Local call tariff
Local call tariff
€ 0.09
09 2290 1908
082161 1658
01803 386 853
00800 3122 1223
01 601 1161
840 320 041
26 84 30 00
France
Germany
Greece
€ 0.09
Free of charge
Local call tariff
€ 0.08
Ireland
Italy
Luxembourg
The Netherlands
Norway
Local call tariff
€ 0.10
0900 0400 063
2270 8250
Local call tariff
Local call tariff
Local call tariff
€ 0.10
Poland
0223491505
2 1359 1440
902 888 785
08 632 0016
02 2310 2116
0207 949 0069
Portugal
Spain
Sweden
Switzerland
United Kingdom
Local call tariff
Local call tariff
Local call tariff
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arfirst.htm [98-07-30 15:22]
Your Guarantee in Central and Eastern Europe
Your Guarantee in Central and Eastern Europe
Dear Customer,
Thank you for purchasing this Philips product, which has been designed and manufactured to the
highest quality standards. If, unfortunately, something should go wrong with this product Philips
guarantees free of charge labor and replacement parts during a period of 36 months from date of
purchase.
What is covered?
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary,
Slovakia, Slovenia, Russia and Turkey and only for monitors originally designed, manufactured,
approved and/or authorized for usage within these countries.
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your
monitor will be serviced in case of defects provided for under the warranty coverage.
What is excluded?
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
●
●
the documents have been altered in any way or made illegible;
the model or production number on the product has been altered, deleted, removed or made
illegible;
●
●
●
repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
●
●
Defects caused by abuse or misuse of the monitor;
Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
Please note that the product is not defective under this guarantee in the case where modifications
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_ee.htm 第 1 頁 / 共 2 [98-07-30 15:22]
Your Guarantee in Central and Eastern Europe
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting our dealers or Information Centers
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer or directly the Philips Service and Consumer Information Centers
Website: http://www.philips.com/support
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_ee.htm 第 2 頁 / 共 2 [98-07-30 15:22]
Consumer Information Centers
Consumer Information Centers
Eastern Europe
BELARUS
Technic al Center of JV IBA
M. Bogdanovich str. 155
BY - 220040 Minsk
Tel: +375 17 217 33 86
BELARUS
Service.BY
Petrus Brovky st. 19 – 101-B
220072, Minsk
Belarus
BULGARIA
LAN Service
140, Mimi Balkanska Str.
Office center Translog
1540 Sofia, Bulgaria
Tel: +359 2 960 2360
CZECH REPUBLIC
General Consumer Information Center
800 142100
Xpectrum
Lu.ná 591/4
CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121 435
Email:[email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 1 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
CROATIA
Renoprom d.o.o.
Ljubljanska 4,
Sv. Nedjelja,10431
Croatia
Tel: +385 1 333 0974
ESTONIA
FUJITSU SERVICES OU
Akadeemia tee 21G
EE-12618 Tallinn
Tel: +372 6519900
HUNGARY
Serware Szerviz
Vizimolnár u. 2-4
HU - 1031 Budapest
Tel: +36 1 2426331
Email: [email protected]
HUNGARY
Profi Service Center Ltd.
123 Kulso-Vaci Street,
H-1044 Budapest ( Europe Center )
Hungary
Tel: +36 1 814 8080
LATVIA
ServiceNet LV
Jelgavas iela 36
LV - 1055 Riga,
Tel: +371 7460399
Email: [email protected]
LITHUANIA
ServiceNet LT
Gaiziunu G. 3
LT - 3009 KAUNAS
Tel: +370 7400088
Email: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 2 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
ROMANIA
Blue Ridge Int'l Computers SRL
115, Mihai Eminescu St., Sector 2
RO - 020074 Bucharest
Tel: +40 21 2101969
SERBIA & MONTENEGRO
Kim Tec d.o.o.
Viline vode bb, Slobodna zona
Beograd L12/3
11000 Belgrade
Serbia
Tel. +381 11 20 70 684
SLOVAKIA
General Consumer Information Center
0800004551
Datalan Servisne Stredisko
Puchovska 8
SK - 831 06 Bratislava
Tel: +421 2 49207155
Email: [email protected]
SLOVENIA
PC HAND
Brezovce 10
SI - 1236 Trzin
Tel: +386 1 530 08 24
Email: [email protected]
RUSSIA
CPS
18, Shelepihinskaya nab.
123290 Moscow
Russia
Tel. +7(495)797 3434
Profservice:
14A -3, 2Karacharovskaya str,
109202, Moscow ,
Russia
Tel. +7(095)170-5401
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 3 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
TURKEY
Türk Philips Ticaret A.S.
Yukari Dudullu Org.San.Bolgesi
2.Cadde No:22
34776-Umraniye/Istanbul
Tel: (0800)-261 33 02
UKRAINE
Comel
Shevchenko street 32
UA - 49030 Dnepropetrovsk
Tel: +380 562320045
LLC Topaz Company
Topaz-Service Company,
Mishina str. 3,
Kiev
Ukraine-03151
Tel: +38 044 245 73 31
Latin America
ARGENTINA
Azopardo 1480.
(C1107ADZ) Cdad. de Buenos Aires
Tel: 0800 3330 856
Email: [email protected]
BRASIL
Alameda Raja Gabaglia, 188 - 10°Andar - V.
Olímpia - S. Paulo/SP - CEP 04551-090 -
Brasil
Tel: 0800-7254101
Email: [email protected]
Pacific
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 4 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
AUSTRALIA
Company: AGOS NETWORK PTY LTD
Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia
Tel: 1300 360 386
Fax: +61-2-80808147
Email: [email protected]
Service hours: Mon.~Fri. 8:00am-7:30pm
NEW ZEALAND
Company: Visual Group Ltd.
Address: 28 Walls Rd Penrose Auckland
Phone: 0800 657447
Fax: 09 5809607
E-mail: [email protected]
Service Hours: Mon.~Fri. 8:30am~5:30pm
Asia
HONG KONG/Macau
Company Name: PHK Service Limited
Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong
Kong
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau
Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau
E-mail: [email protected]
Service Hours: Mon.~Sat. 09:00am~06:00pm
India
Company: REDINGTON INDIA LTD
Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India
Tel: +9144-42243352/353
E-mail: [email protected]
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 5 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
Indonesia
Company Name: PT. Gadingsari elektronika Prima
Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang. Jakarta
Tel: 021-750909053, 021-750909056
Fax: 021-7510982
E-mail: [email protected]
Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm
Additional service points:
1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan.
Phone: 021-7940040, ext 1722/1724, 98249295, 70980942
2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat.
Phone: 021-3455150, 34835453
3. Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-
45870601, 98131424
South Korea
Company: PCS One Korea Ltd.
Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea
Call Center Tel: 080-600-6600
Tel: 82 2 591 1528
Fax: 82 2 595 9688
E-mail: [email protected]
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM
Malaysia
Company: After Market Solutions (CE) Sdn Bhd
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia.
Phone: 603 7953 3370
Philips Info Line: 1-800-880-180
Fax: 603 7953 3338
E-mail: [email protected]
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm
Pakistan
Philips Consumer Service
Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400
Tel: (9221) 2737411-16
Fax: (9221) 2721167
E-mail: [email protected]
Website: www.philips.com.p
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 6 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
Singapore
Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center)
Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762
Tel: (65) 6882 3999
Fax: (65) 62508037
E-mail: [email protected]
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm
Taiwan
Company: FETEC.CO
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800
Consumer Care: 0800-231-099
Tel: (03)2120336
Fax: (03)3129184
E-mail: [email protected]
Service hours: Mon.~Fri. 8:30am~7:00pm
Thailand
Company: Axis Computer System Co., Ltd.
Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310
Thailand
Tel: (662) 934-5498
Fax: (662) 934-5499
E-mail: [email protected]
Service Hours: Mon.~Fri. 08:30am~05:30pm
Vietnam
Company: Digiworld Corp
Address: 211-213 Vo Van Tan St, Ward 5, Dist.3 , Ho Chi Minh city, Vietnam
Tel: 848-38266065
Fax: 848-38267307
E-mail: [email protected]
Service hours: 8:00 to 12:00 AM and 13:30 to 17:30 PM (from Monday to Friday)
Philippines
Glee Electronics Inc
Contact nos. (632) 636-3636 / 7064028 to 29
Fax no. (632) 7064026
Receiving Centers
NEO CARE - Megamall
4th Level Cyberzone, Building B,
SM Megamall, Mandaluyong City
NEO CARE - SM North EDSA
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 7 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
4th Level Cyberzone, Annex Bldg.
SM City North EDSA, Quezon City
441-1610
MDR Microware Sales Inc.
Cebu Branch
N. Escario corner Clavano St., Cebu City Phils.
# 255-4415/ 255-3242/253-9361/4124864 to 67
Sun # 0922-8210045 to 46
Davao Office:
C. Arellano St., Davao City 8000
082- 225-3021/225-3022
Sun# 0922-8210015
CDO Office:
1445 Corrales Ext.,CDO City
088-856-8540/856-8541
Sun # 0922-8210080
Iloilo Office:
C. Lim Comp., Gomez St., Iloilo City
# 033 338-4159/ 033 508-3741
Sun # 0922-8808850
Africa
SOUTH AFRICA
Company name: Sylvara Technologies Pty Ltd
Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa
Tel: +27878084456
Fax: +2711 391 1060
E-mail: [email protected]
Service hours: Mon.~ Fri. 08:00am~05:00pm
Middle East
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 8 頁 / 共 9 [98-07-30 15:22]
Consumer Information Centers
Middle East + North Africa
Company: AL SHAHD COMPUTER L.L.C
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES
TEL: 00971 4 2276525
FAX: 00971 4 2276242
E-mail: [email protected]
Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm
Israel
Company: Eastronics LTD
Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel
Tel: 1-800-567000 call free in Israel; (972-50-8353722 after service hours until 20:00)
Fax: 972-3-6458759
E-mail: [email protected]
Service hours: Sun.~Thurs. 08:00 - 18:00
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ arcic.htm 第 9 頁 / 共 9 [98-07-30 15:22]
International Guarantee
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product which has been designed and manufactured to the
highest quality standards.
If, unfortunately, something should go wrong with this product Philips guarantees free of charge
labor and replacement parts irrespective of the country where it is repaired during a period of 12
months from date of purchase. This international Philips guarantee complements the existing
national guarantee obligations to you of dealers and Philips in the country of purchase and does not
affect your statutory rights as a customer.
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
●
●
the documents have been altered in any way or made illegible;
the model or production number on the product has been altered, deleted, removed or made
illegible;
●
●
repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Please note that the product is not defective under this guarantee in the case where modifications
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer. In the event you require service whilst in another country a dealer address can be given to
you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can
be found in the relevant part of this booklet.
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting your dealer. If you have questions which your dealer cannot answer or
Website: http://www.philips.com
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_intl.htm 第 1 頁 / 共 2 [98-07-30 15:22]
International Guarantee
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_intl.htm 第 2 頁 / 共 2 [98-07-30 15:22]
United States Guarantee
Your Philips F1rst Choice Warranty(USA)
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and
deliver high-quality performance, ease of use and ease of installation. Should
you encounter any difficulties while installing or using this product, please
contact Philips directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site within 48
hours of your call being received within the first year of purchase. If you have
any problems with your monitor within the second or third year of purchase, we
will repair it after it has been sent to the service provider at your expense and
returned to you within five working days, free of charge.
LIMITED WARRANTY (Computer Monitor)
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two
business days for the first year. This product must be shipped in at your expense for service during
years two and three.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document
showing that you purchased the product is considered proof of purchase. Attach it to this owner's
manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the
replacement or repair of all parts, and for all labor charges.
All parts, including repaired and replaced parts, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on all replaced and repaired
products and parts also expires.
WHAT IS EXCLUDED?
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 1 頁 / 共 4 [98-07-30 15:22]
United States Guarantee
Your warranty does not cover:
●
●
●
●
labor charges for installation or setup of the product, adjustment of customer controls on the
product, and installation or repair of antenna systems outside of the product.
product repair and/or part replacement because of misuse, accident, unauthorized repair or
other cause not within the control of Philips Consumer Electronics.
reception problems caused by signal conditions or cable or antenna systems outside the
unit.
a product that requires modification or adaptation to enable it to operate in any country other
than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
●
●
incidental or consequential damages resulting from the product. (Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not
copyrighted.)
the model or production number on the product has been altered, deleted, removed or made
illegible.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the
product, the local Philips service organization will attempt to provide service (although there may be
a delay if the appropriate spare parts and technical manual(s) are not readily available).
Where CAN I GET MORE INFORMATION?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.
customers only) or (919) 573-7855.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls
discussed there may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and
procedures for servicing:
Philips Customer Care Center
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 2 頁 / 共 4 [98-07-30 15:22]
United States Guarantee
(877) 835-1838 or (919) 573-7855
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on how long an implied
warranty may last, this limitation may not apply to you.)
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
Three years free parts and three years free labor will be provided at Philips Canada depot or any
one of its authorized service centers.
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed
or implied, including any implied warranties of merchantability or fitness for a particular purpose.
Philips is not liable under any circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified of the possibility of such damages.)
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/
province to state/province.
Before contacting Philips, please prepare the following details so we can solve your problem
quickly.
●
●
Philips type number
Philips serial number
●
●
Purchase date (copy of purchase may be required)
PC environment Processor:
ꢀ❍
ꢀ❍
ꢀ❍
CUP and Graphic card name and driver version
Operating system
Application being used
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 3 頁 / 共 4 [98-07-30 15:22]
United States Guarantee
●
●
Other cards installed
Having the following information available will also help speed up the process:
Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
●
The full address to which the swap model should be delivered.
Just a phone call away
Philipsꢀ customer help desks are located worldwide. Within the U.S. you can contact Philips
customer care Monday-Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from
10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers.
For more information on this and more great Philips products visit our website at:
Website: http://www.philips.com
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/ arranty/ ar_usa.htm 第 4 頁 / 共 4 [98-07-30 15:22]
Do nload and Print
Download and Print
ꢀ
ꢀ
Installing Your LCD monitor driver
System requirements:
●
●
PC running Windows® 2000 , Windows® XP, Windows® Vista or later
Find your driver ".inf/.icm/.cat" at : /PC/drivers/
Read the "Readme.txt" file before installing.
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into
your hard disk, then viewed and printed with Acrobat Reader or through your browser.
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application.
Download instructions:
To download the file:
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/2000/Me/XP/Vista users right-
click)
Download
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to
Disk'.
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or
'source', choose 'source').
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/do nload/do nload.htm 第 1 頁 / 共 2 [98-07-30 15:22]
Do nload and Print
Printing instructions:
To print the manual:
With the manual file open, follow your printer's instructions and print the pages you need.
Download from Www.Somanuals.com. All Manuals Search And Download.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/223E1/223E1-EDFU/5B.10N01.001/CD-Contents/lcd/manual/ENGLISH/do nload/do nload.htm 第 2 頁 / 共 2 [98-07-30 15:22]
|