DJ EFFECTOR
EFX-1000
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filed
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
or moisture.
D3-4-2-1-3_A_En
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated SHOCK, DO NOT REMOVE COVER (OR
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
When using this product follow the instructions
written on the underside of the unit, which
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
concern rated voltage, etc.
D3-4-2-2-4_En
IMPORTANT NOTICE THE SERIAL NUMBER FOR
–
D3-4-2-1-1_En-A
THIS EQUIPMENT IS LOCATED IN THE BOTTOM.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR
ENCLOSED WARRANTY CARD AND KEEP IN A
SECURE AREA. THIS IS FOR YOUR SECURITY.
NOTE: THE NO USER-SERVICEABLE PARTS COMPARTMENT WARNING IS LOCATED ON THE APPLIANCE BOTTOM.
D1-4-2-6-1_En
READ INSTRUCTIONS — All the safety and
operating instructions should be read before the
product is operated.
RETAIN INSTRUCTIONS — The safety and
operating instructions should be retained for
future reference.
HEED WARNINGS — All warnings on the product
and in the operating instructions should be
adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
CLEANING — The product should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides
or other volatile liquids since they may corrode
the cabinet.
ATTACHMENTS — Do not use attachments not
recommended by the product manufacturer as
they may cause hazards.
WATER AND MOISTURE — Do not use this
product near water — for example, near a
bathtub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming
pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
GROUNDING OR POLARIZATION
OBJECT AND LIQUID ENTRY — Never push
objects of any kind into this product through
openings as they may touch dangerous voltage
points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the product.
SERVICING — Do not attempt to service this
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
Information to User
•
If this product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other), it will fit into the
outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alteration or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_En
This Class B digital apparatus complies with
Canadian ICES-003.
•
If this product is equipped with a three-wire
grounding type plug, a plug having a third
(grounding) pin, it will only fit into a grounding
type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding type plug.
DAMAGE REQUIRING SERVICE — Unplug this
product from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
Cet appareil numérique de la Classe B est conforme
à la norme NMB-003 du Canada.
D8-10-1-3_EF
•
When the power-supply cord or plug is
damaged.
•
If liquid has been spilled, or objects have fallen
into the product.
POWER-CORD PROTECTION — Power-supply
cords should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
OUTDOOR ANTENNA GROUNDING — If an
outside antenna or cable system is connected to
the product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of
antenna-discharge unit, connection to
•
•
If the product has been exposed to rain or water.
If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
If the product has been dropped or damaged in
any way.
CAUTION
– PREVENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD.
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
•
•
When the product exhibits a distinct change in
performance — this indicates a need for service.
ATTENTION – POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER
REPLACEMENT PARTS — When replacement parts
are required, be sure the service technician has
used replacement parts specified by the
manufacturer or have the same characteristics
as the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
SAFETY CHECK — Upon completion of any service
or repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
WALL OR CEILING MOUNTING — The product
should not be mounted to a wall or ceiling.
HEAT — The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers)
that produce heat.
CETTE FICHE POLARISEE AVEC UN
PROLONGATEUR UNE PRISE DE
COURANT OU UNE AUTRE SORTIE
DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE
CART — A product and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product
and cart combination to overturn.
grounding electrodes, and requirements for the
grounding electrode. See Figure A.
LIGHTNING — For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
POWER LINES — An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can fall into such power
lines or circuits. When installing an outside
antenna system, extreme care should be taken
to keep from touching such power lines or
circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
A DECOUVVERT.
D2-4-4-1_EF
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to lead, a chemical known to
the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
VENTILATION — Slots and openings in the cabinet
are provided for ventilation and to ensure
reliable operation of the product and to protect
it from overheating, and these openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided or the
Wash hands after handling
D36-P4_En
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
manufacturer’s instructions have been adhered
to.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
POWER SOURCES — This product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your product dealer or local power
company.
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the
appliance should be unplugged from the outlet
when left un-used for a long period of time.
ELECTRIC
SERVICE
EQUIPMENT
POWER-CORD CAUTION
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement. S002_En
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Fig. A
NEC — NATIONAL ELECTRICAL CODE
D1-4-2-2_En
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_En
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and
televisions, use shielded cables and connectors for connections.
D8-10-3a_En
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know
how to operate your model properly. After you have finished
reading the instructions, put them away in a safe place for future
reference.
CONTENTS
In some countries or regions, the shape of the power plug and
power outlet may sometimes differ from that shown in the
explanatory drawings. However the method of connecting and
FEATURES ................................................................... 3
CONFIRM ACCESSORIES ........................................... 3
operating the unit is the same.
K015 En
QUICK OPERATION GUIDE
USING BEAT EFFECTS [BPM MODE]........................ 4
USING BEAT EFFECTS [RHYTHM MODE] ................ 5
USING THE DIGITAL JOG BREAK ............................. 6
USING JOG MEMORY PLAY...................................... 6
FEATURES
1 High-Fidelity Sound
BEFORE USE
CONNECTIONS............................................................ 7
Connection Panel................................................... 7
Basic Connections ................................................. 8
EFFECTS ..................................................................... 10
Beat Effects .......................................................... 10
Digital Jog Break ................................................. 12
Effect Parameters ................................................ 13
CONTROLS AND FUNCTIONS ................................. 14
Control Panel ....................................................... 14
The high-fidelity design features a 24-bit A/D and D/A
converter (96 kHz sampling) and 32-bit DSP, allowing the
addition of effects without lowering the original sound
quality; a relay bypass function has also been adopted.
2 3-Band Beat Effector
1) Beat effects [BPM mode]
OPERATIONS
Equipped with the same automatic BPM counter/beat
effector made popular by the EFX-500. Allows effect
processing on single selected bands in synch with the track
tempo (BPM), for greater expressive possibilities than with
conventional all-band effecters.
OPERATIONS ............................................................. 17
Adjusting Input Level .......................................... 17
Adjusting Effect Output Level ............................ 17
Selecting Signal Flow ......................................... 17
Selecting Foot Switch Operation ....................... 17
Selecting the Level Meter Display ..................... 17
Digital Link Function ........................................... 17
Bypass Function .................................................. 17
Beat Effects [BPM mode] .................................... 18
Beat Effects [RYHTHM mode] ............................ 19
Digital Jog Break ................................................. 20
Jog Memory......................................................... 20
2) Beat effects [RHYTHM mode]
This industry-first rhythm effector lets you apply effects in
synch with the rhythm you input yourself.
With the expression of a far wider range of unique effects
compared to previous beat effectors, you have the potential
for a new level of DJ performance.
3 Digital Jog Break Function
MIDI SETTINGS
MIDI SETTINGS ......................................................... 21
Synchronizing an external sequencer to an
audio signal, or using EFX-1000 operation
data to operate an external sequencer ............. 21
To synchronize beat effects to external
The Jog dial allows real-time control of effect sounds. Up to
eight seconds of Jog function can be stored in memory for
automated replay. Up to 49 effects can be demonstrated in
combination with the beat effector.
sequencer, or use an external sequencer to
operate the EFX-1000 .......................................... 21
MIDI Implementation Chart ................................ 22
Control Change (CC) Table ................................. 22
Program Change.................................................. 24
About Rhythm Effects ......................................... 24
Snapshot .............................................................. 24
4 MIDI IN/OUT Function
External MIDI signals (control signals and timing clock
signals) can be used to control the effector, and as a
medium for using the effector to control a sequencer or
other component.
OTHER
5 Digital Link Function
TROUBLESHOOTING ................................................ 25
SPECIFICATIONS....................................................... 27
BLOCK DIAGRAM...................................................... 27
A variety of functions can be performed by using the
dedicated digital link cable to connect this unit to a Pioneer
DJ mixer (DJM-1000) with digital link support.
CONFIRM ACCESSORIES
Operating Instructions........................................................... 1
Digital link cable..................................................................... 1
Power cord ............................................................................. 1
Warranty ................................................................................. 1
6 Digital IN/OUT
Equipped with digital IN/OUT connectors with 24-bit/96 kHz
sampling, allowing use in studio track creation and other
applications where high sound quality is demanded.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK OPERATION GUIDE (1/3)
Adjusting the input level
Input signals to the input
connectors, and adjust the
INPUT LEVEL dial.
Adjusting effect output level
Rotate the EFFECT OUT LEV. dial to
adjust the effect output level.
Changing the level meter display mode
Each time the METER MODE button is pressed, the
level meter display alternates as follows:
÷ INPUT, OUTPUT light: Input and output monaural
display.
÷ INPUT, L, R light: Input stereo display.
÷
OUTPUT, L, R light: Output stereo display.
USING BEAT EFFECTS [BPM MODE]
1. Select the BPM measurement mode.
Press the BPM MODE button so that the
button lights together with the desired mode
indicator (AUTO/MIDI/TAP).
EFFECT TIME
display
DEPTH dial
Sets the parameter 1 of each
effect.
2. Select effect type.
Press the DELAY, ECHO, PITCH ECHO,
TRANS, FLANGER, FILTER or PHASER button
and the pressed button starts to flash.
BPM
measurement
mode
RHYTHM TAP display
BPM COUNTER
3. Select the sound range for the effect.
Press the button of the frequency (LOW, MID,
HI) you wish to affect by the beat effect and
the corresponding indicator lights.
indicators
4. Select the beat with which the effect is
to be synchronized.
Press a beat select button (1/8, 1/4, 1/2, 3/4,
1/1, 2/1, 4/1 or 8/1) to light the desired button.
5. Apply an effect.
Press the lever towards you (ON position) to
start operation; release it and it returns to
the center position (OFF position). In the
center position (OFF position), the original
sound is not affected. Press the lever away
from you to lock it in position so that the
beat effect is applied also when the lever is
released.
TIME/BPM dial
Set the desired effect time as in step 4.
Turn the TIME/BPM dial while holding down
the TAP/SHIFT button to make the desired
BPM setting. When also the BPM MODE
button is held down, BPM can be set in 0.1
increments.
TAP/SHIFT button
BPM can be manually adjusted by adjusting
the beat (quarter notes) and hitting this key
two times or more.
MIX dial
Adjusts the balance between
the original sound and effects.
CHARACTER dial
Sets the parameter 2 of each
effect.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK OPERATION GUIDE (2/3)
BYPASS button
When the button is pressed (button
indicator flashes), the signal entering
the input connectors is output
directly (without modification) to the
output connectors.
SIGNAL FLOW switch
Selects the order in which signals
are passed through the electronic
sections (from beat effect to digital
jog break, or vice versa).
USING BEAT EFFECTS [RHYTHM MODE]
1. Select the rhythm input mode.
Press the RHYTHM MODE button so that the
button indicator lights.
EFFECT
DEPTH dial
TIME display
Sets the parameter 1 of each
effect.
2. Select effect type.
BPM
Press the DELAY, ECHO, PITCH ECHO, TRANS,
FLANGER, FILTER or PHASER button and the
pressed button starts to flash.
measurement
mode
indicators
RHYTHM TAP display
BPM COUNTER
3. Select the sound range for the effect.
Press the button of the frequency (LOW, MID,
HI) you wish to affect by the rhythm effect and
the corresponding indicator lights.
4. Set to REC mode.
¶ When the REC button is pressed, the
BPM display indicates “
”.
¶ If no rhythm has been input, the unit
will automatically enter the REC mode
in step 1.
5. Input the rhythm.
Tap your finger on the TAP button to input the
desired rhythm. As you input the rhythm, the
rhythm will be calculated and displayed on the
RHYTHM TAP display (up to 8 taps with tap
interval of 2 seconds or less).
6. Select the overall rhythm time.
The pressed beat select button will light, and
the overall rhythm time will be set at the
multiple corresponding to the pressed button.
7. Apply an effect.
Press the lever towards you (ON position) to
start operation; release it and it returns to the
center position (OFF position). In the center
position (OFF position), the original sound is
not affected. Press the lever away from you to
lock it in position so that the rhythm effect is
applied also when the lever is released.
MIX dial
Adjusts the balance
between the original
sound and effects.
BPM MODE button
When the BPM MODE button is
pressed while in the rhythm
mode, the mode changes to
the beat effect BPM mode.
CHARACTER dial
Sets the parameter 2 of
each effect.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK OPERATION GUIDE (3/3)
USING THE DIGITAL JOG BREAK
1. Select the desired effect.
Press the desired effect button, JET, WAH,
PHASE SHIFTER, RING, ZIP, HUMANIZER or
VOCODER to flash the corresponding button.
2. Apply the desired effect.
Turn the Jog dial either while pressing the
lever towards you or pressing it away
from you (ON position). As the Jog dial is
turned, parameters change gradually and
the selected effect is applied. When the
dial rotation is stopped, the parameter
returns to normal.
When the lever is pressed towards you,
releasing it causes it to automatically
return to the center (OFF position).
DEPTH dial
Sets the parameter
1 of each effect.
DIGITAL JOG BREAK METER
Indicates the amount of control
exercised by the Jog dial.
HOLD button
When this button is pressed so that
the button indicator lights, effects
produced with the Jog dial will
continue even when your hand is
removed from the dial.
USING JOG MEMORY PLAY
1. Hold the Jog memory button (M)
depressed while rotating the Jog dial.
Effect changes produced with the Jog dial will be
stored in memory (maximum 8 seconds). When
storage is completed, the SINGLE and LOOP
buttons light.
2. Press the SINGLE button or LOOP
button
÷ When the SINGLE button is pressed, the
stored Jog-dial effect change will be replayed
one time only.
÷ When the LOOP button is pressed, the stored
Jog-dial effect change will be replayed
repeatedly. Press the button once more to stop
the effect.
MIX dial
Adjusts the balance between
the original sound and effects.
CHARACTER dial
Sets the parameter 2 of each
effect.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE (CONNECTIONS)
CONNECTIONS
Connection Panel
1 Power input socket (AC IN)
Use the provided power cord to connect this socket to an
AC outlet.
9 Audio INPUT/OUTPUT jacks
Uses 6.3mm phones plug. For monaural inputs, connect L
input channel only for output on both L and R channels.
Audio inputs are throughput (output) even when the unit’s
power is turned OFF.
2 POWER switch
3 Digital OUTPUT fs SELECT switch
Use to change the digital output frequency sampling rate
(fs) (44.1kHz/48kHz/96kHz).
10 Audio INPUT/OUTPUT jacks
INPUT/OUTPUT connectors using RCA pin jacks.
Audio inputs are throughput (output) even when the unit’s
power is turned OFF.
4 Link input/output connector (EFX LINK)
When the accessory digital link cable is used to connect
this connector to the DJ-mixer DJM-1000 (with digital link
support), digital link functions can be used, permitting a
variety of new functions.
7
Before making or changing the connections,
switch off the power switch and disconnect the
power cord from the AC outlet. This precaution
should also be taken when changing the IN & OUT
LEVEL switch and DIGITAL fs SELECT switch.
CAUTION:
÷ When connections are made to the phone jack inputs
and a monaural signal cable is connected to the L
(MONO) terminal, inputs can be made to both the L and
R channels.
÷ After all other connections are made, connect the power
cord to a household wall outlet or to the auxiliary AC
power takeoff on your amplifier.
The EFX LINK connector is designed to be connected
via the provided digital link cable ONLY to a component
equipped with the designated digital link function.
The unit may be damaged if this connector is
mistakenly connected to any other component.
5. MIDI input/output connectors (MIDI OUT, MIDI IN)
See page 21 for instructions on how to
use the MIDI terminals.
Use to connect the effector to a MIDI component (see page 21).
6 Digital input/output connectors (DIGITAL IN,
DIGITAL OUT)
Use to connect the effector to a component provided with
coaxial digital input/output connectors.
CAUTION:
Do not make any connections that may create signal
loops as this will cause circuit oscillations which
could damage the speakers.
7 Foot switch jack (FOOT SW)
Can be connected to a ON/OFF type foot switch with 6.3mm
phone plug to allow ON/OFF control of effects.
Foot switches are available in several types, including
press-ON, press-OFF, and latching-type ON/OFF.
[Example of connections that must not be
performed]
¶ Do not connect the output of the DJ Mixer to the
input terminal of the Effector and the output of the
Effector to the input terminal of the same mixer.
¶ Do not connect the SEND output of the DJ Mixer to
the input terminal of the Effector and the output of
the Effector to the input terminal of the DJ Mixer
(except for the RETURN terminal).
8 Input/output gain select switch (IN&OUT LEVEL)
Use to select the input/output gain (–10dB / +4dB).
Installation Location
Cleaning the unit
÷ Avoid mounting on top of amplifiers, near spotlights, or
other heat-emitting components and appliances;
extended exposure to heat can cause damage to the
effector itself.
To clean the unit wipe with a polishing or a soft, dry cloth.
For stubborn dirt, moisten a soft cloth with a weak solution
of neutral detergent (diluted in five to six parts water),
wring the cloth well, and wipe away the dirt. Use a dry cloth
to wipe the surface dry. Do not use volatile liquids such as
benzene or thinner which will damage to the unit.
÷ Install this unit as far as possible away from tuners and TV
sets. A unit installed in close proximity to such equipment
may cause noise or degradation of the picture.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE (CONNECTIONS)
Basic Connections
Before making or changing the connections, switch off the power switch and disconnect the power cord from the AC outlet.
1. Connecting the SEND/RETURN Terminals on the
DJ Mixer (on DJ mixer provided with SEND and
RETURN terminals)
÷ Make connections using cables with 1/4-inch/6.3 mm in
diameter phone plugs.
÷ If the DJ mixer supports digital link, it can be connected
to the EFX LINK connector using the provided digital link
cable to eliminate the need for connection by an analog
6.3mm phone plug cable (audio signals transmitted over
the digital link cable are in digital format). Also note that
extraneous noise may result if both analog and digital
link cables are connected simultaneously.
÷ Set the DJ mixer so that the SEND and RETURN
terminals can be used.
÷ Set the IN & OUT LEVEL switch on the Effector
to the [–10 dB] position.
Effector EFX-1000
FOOT SW
Stereo Amplifier
OUTPUT
INPUT
EFX LINK
Accessory
digital
link cable
Foot switch
(pedal switch)
: Signal flow
DJ Mixer
MASTER OUT
SEND
SEND
1
–26
+6
RETURN
RETURN
1
CH-1
DJ CD Player
DJ CD Player
CH-2
2. Connecting a DJ Mixer and an Audio Amplifier
(on DJ mixer not provided with SEND and
RETURN terminals)
÷ When making connections, do not connect both RCA pin
plug cables and phones plug cables for the same
connection function (use either one or the other, not
both). Also, if you wish to use analog connections, do
not also make connections to the digital connectors
(digital signals are given priority when connected).
¶ For digital connections, use RCA pin-plug coaxial cables.
Set the OUTPUT fs SELECT switch in accordance with
the connected component.
÷ Connect using cables with phone plugs (1/4-inch/6.3 mm
in diameter) or RCA pin plugs.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE (CONNECTIONS)
÷ Set the IN & OUT LEVEL switch
on the Effector to the [+4 dB]
position.
OUTPUT
L
R
MASTER OUT
L
L
R
R
INPUT
INPUT
Effector EFX-1000
L
R
MASTER OUT
DIGITAL OUT
Stereo Amplifier
DJ Mixer
3. Connecting a DJ CD Player and a DJ Mixer (this
connection applies effects only to the sound of
the DJ CD player on channel 2)
¶ Connect the units using a cable with RCA pin plugs.
¶ For digital connections, use RCA pin-plug coaxial cables.
÷ Set the IN
&
OUT
Effector EFX-1000
LEVEL switch on the
Effector to the [–10 dB]
position.
AUDIO OUT
L
L
R
R
INPUT
DIGITAL
IN
DIGITAL OUT
OUTPUT
DIGITAL
IN
DIGITAL
IN
DIGITAL OUT
DIGITAL
OUT
DJ Mixer
DJ CD Player
4. Connecting the power cord
÷ After all other connections are completed, insert the
power cord’s plug into a wall power outlet or the
auxiliary power outlet of an amplifier.
CAUTION:
Signal inputs are handled in a specific order of
priority:
EFX LINK > digital inputs > analog inputs
When EFX LINK signals are input, digital signals are
not output.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECTS (Beat Effects)
EFFECTS
Beat Effects
1. DELAY effect
2. ECHO effect
[RHYTHM mode]
Adds delay sound to the original sound.
[BPM mode]
Adds delay sound to the original sound.
[BPM mode]
Changes the pitch of the TAP delay sound,
and applies the effect to the original sound.
Although a maximum of 8-TAPs can be
recorded, only 4-TAPs can be used for
effect.
A delay sound is added to the original
sound at the value set with the TIME dial.
A delay sound is added to the original
sound at the value set with the TIME dial.
[RHYTHM mode]
Adds TAP delay sound to the original
sound (Max 8-TAP).
÷
The DEPTH dial can be used to adjust
the feedback level. Feedback means to
input the delay sound back into the
delay input. This control allows the
amount of the feedback to be adjusted
(near the [MAX] setting, the sound level
rises).
÷
The DEPTH dial can be used to adjust
the TAP delay level (near the [MAX]
setting the sound volume will rise
somewhat).
Difference from the DELAY effect:
÷
Even if the BEAT EFFECTS lever switch
is moved from [ON] to [OFF], the
feedback sound or TAP delay sound will
continue.
÷
÷
The CHARACTER dial can be used to
adjust the pitch of the TAP delay sound.
The MIX dial can be used to adjust the
levels of the original and pitch echo
sounds.
÷
÷
The CHARACTER dial can be used to
adjust the amount of filter applied to the
feedback sound.
The MIX dial can be used to adjust the
levels of the original and delay sounds.
÷
In the BPM mode, if the DEPTH dial is
set to [MAX] and the BEAT EFFECTS
lever switch is moved from [ON] to
[OFF], a hold-delay effect will be
produced without attenuating the
feedback sound (near the [MAX] setting,
the sound level rises).
TAP 1 pitch
echo block.
TIME
TAP 2 pitch
echo block.
In the RHYTHM mode, when the switch
is turned [OFF] the effect will end with
the final TAP delay sound for the
original sound.
DEPTH
Time
TAP 3 pitch
echo block.
Original
sound
Feedback
Delay sound
TAP 4 pitch
echo block.
BPM mode
Delay block
Echo block
4. TRANS effect
Cuts the original sound intermittently.
[BPM mode]
Cuts the sound at the interval set by the
TIME dial (cuts latter half of the interval).
RHYTHM mode
[RHYTHM mode]
A delay sound set with the TAP button
(TAP delay sound) is added to the original
sound (Max 8-TAP).
TAP 1 echo
block
÷
The DEPTH dial can be used to adjust
÷
÷
÷
The DEPTH dial can be used to adjust
the TAP delay level (near the [MAX]
setting the sound volume will rise).
The CHARACTER dial can be used to
adjust the amount of filter applied to the
TAP delay sound.
The MIX dial can be used to adjust the
levels of the original and TAP delay
sounds.
the amount that is cut.
TAP 8 echo
block
Time
Cut
3. PITCH ECHO effect
Time
Changes the pitch of the delay sound, and
applies the effect to the original sound.
In the same way as for the ECHO effect, the
effect sound is maintained even if the BEAT
EFFECTS lever switch is set from [ON] to
[OFF].
Cut
Time
÷
The CHARACTER dial can be used to
adjust the phase difference between L
and R channels.
DEPTH
Time
[BPM mode]
Changes the pitch of the delay sound set
with the TIME dial, and applies the effect to
the original sound.
Original Delay
sound sound
Delay Delay
sound sound sound
Delay
Time
Time
÷
÷
÷
The DEPTH dial can be used to adjust
the feedback level.
The CHARACTER dial can be used to
adjust the pitch of the delay sound.
The MIX dial can be used to adjust the
levels of the original and pitch echo
sounds.
Time
Time
TAP 1 delay
block
÷
The MIX dial can be used to adjust the
Pitch echo
block
levels of the original and trans sounds.
TAP 8 delay
block
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECTS (Beat Effects)
[RHYTHM mode]
Cuts the original sound in synch with the
TAP rhythm (Max 8-TAP).
6. FILTER effect
7. PHASER effect
A low-pass filter is applied to the original
sound to produce more muted sound.
[BPM mode]
Causes a phase effect by applying a phase-
shifted sound to the original sound.
[BPM mode]
÷
The DEPTH dial can be used to adjust the
amount that is cut.
The cutoff frequency of the low-pass filter
changes with the cycle set by the TIME dial.
Changes the frequency range to which the
phase effect is applied at the interval set by
the TIME dial.
÷
The CHARACTER dial can be used to
adjust of phase difference between L
and R channels.
÷
The DEPTH dial is used to change the
unique coloring of the sound by
adjusting the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
÷
The DEPTH dial can be used to adjust
the strength of the phase effect by
changing the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
The CHARACTER dial can be used to
adjust the cyclic changes in the phase
effect.
÷
The MIX dial can be used to adjust the
levels of the original and trans sounds.
5. FLANGER effect
÷
÷
By applying a time-shifted sound to the
original, the effect of an ascending or
descending jet plane (flange effect) is
produced.
The MIX dial can be used to adjust the
levels of the original and phaser
sounds.
[BPM mode]
Changes the frequency range to which the
flange effect is applied at the interval set by
the TIME dial.
÷
The CHARACTER dial can be used to
vary the cutoff frequency of the cyclic
low-pass filter.
÷
The DEPTH dial can be used to adjust
the strength of the flange effect by
changing the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
The CHARACTER dial can be used to
adjust the cyclic changes in the flange
effect.
Phase effect change
Time
÷
÷
Phase effect change
Time
The MIX dial can be used to adjust the
levels of the original and flanger sounds.
÷
The MIX dial can be used to adjust the
levels of the original and filter sounds.
Phase effect change
Time
[RHYTHM mode]
Changes cutoff frequency of the low-pass
filter, in synch with the TAP rhythm (Max 8-
TAP).
Flange effect change
Time
[RHYTHM mode]
Changes the frequency subjected to phase
effect, in sync with the TAP rhythm (Max 8-
TAP).
÷
The DEPTH dial is used to change the
unique coloring of the sound by
adjusting the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
Flange effect change
Time
÷
The DEPTH dial can be used to adjust
the strength of the phase effect by
changing the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
The CHARACTER dial can be used to
adjust the cyclic changes in the phase
effect.
÷
÷
The CHARACTER dial can be used to
vary the cutoff frequency of the cyclic
low-pass filter.
The MIX dial can be used to adjust the
levels of the original and filter sounds.
Flange effect change
Time
÷
÷
[RHYTHM mode]
The MIX dial can be used to adjust the
levels of the original and phaser
sounds.
Changes the frequency subjected to flange
effect, in synch with the TAP rhythm (Max
8-TAP).
÷
The DEPTH dial can be used to adjust
the strength of the flange effect by
changing the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
The CHARACTER dial can be used to
adjust the cyclic changes in the flange
effect.
÷
÷
The MIX dial can be used to adjust the
levels of the original and flanger sounds.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECTS (Digital Jog Break)
Digital Jog Break
÷
The DEPTH dial can be used to adjust
the Jog dial’s variable range (step).
1. JET effect
3. PHASE SHIFTER effect
A phase-shifted sound is added to the
original, thus producing a phase shifter
effect.
A time-shifted sound is applied to the
original, thus producing the effect of a jet
airplane ascending or descending (flange
effect).
÷
The Jog dial is used to change the
frequency range that is affected by the
phase effect.
÷
The Jog dial is used to change the
frequency range that is affected by the
flange effect.
REV
FWD
Jog dial
Phase effect change
÷
÷
The CHARACTER dial can be used to
adjust the reverb effect
Flange effect change
REV
FWD
REV
FWD
Reverb
Zip block
block
Jog dial
Jog dial
÷
÷
The amount of resonance is changed
using the DEPTH dial to emphasize the
phase effect. (When approaching the
[MAX] setting, the level of the sound
increases.)
The MIX dial can be used to adjust the
levels of the zip+reverb and original
sounds.
÷
÷
The amount of resonance is changed
using the DEPTH dial to emphasize the
flange effect. (When approaching the
[MAX] setting, the level of the sound
increases.)
6. HUMANIZER effect
The original sound is modified to resemble
the vowel sounds of the human voice.
The CHARACTER dial can be used to
adjust the reverb effect.
The CHARACTER dial can be used to
adjust the reverb effect.
÷
The Jog dial is used to vary the vowel
sound coloration.
Phase shifter
block
Reverb
block
Reverb
Jet block
block
÷
The MIX dial can be used to adjust the
levels of the phase shifter + reverb
sound and the original sound.
÷
The MIX dial can be used to adjust the
levels of the jet + reverb sound and
original sound.
REV
FWD
Jog dial
4. RING modulator effect
÷
÷
The DEPTH dial is used to change the
unique coloring of vowel sounds by
adjusting the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
2. WAH effect
By modulating the original sound in the
shape of a sine wave, the resulting sound
coloration resembles a ringing bell.
The filter’s cutoff frequency is shifted,
causing great change in the sound tone.
÷
The Jog dial is used to vary the filter’s
÷
The Jog dial is used to vary the sine
wave frequency.
cutoff frequency.
The CHARACTER dial can be used to
adjust the reverb effect.
Frequency
Humanizer
block
Reverb
block
REV
FWD
Jog dial
÷
The MIX dial can be used to adjust the
levels of the humanizer + reverb and the
original sounds.
Jog dial
÷
÷
The DEPTH dial can be used to adjust
the amplitude of the sine wave.
The CHARACTER dial can be used to
adjust the reverb effect.
Frequency
Jog dial
7. VOCODER effect
The input sound is replaced by an inter-
nally generated signal sound, producing a
mechanical sound effect.
÷
The DEPTH dial is used to change the
unique coloring of the sound by
adjusting the amount of resonance.
(When approaching the [MAX] setting,
the level of the sound increases.)
Reverb
block
Ring block
÷
The Jog dial is used to change the
frequency of the internally generated
signal sound.
The DEPTH dial can be used to vary the
internally generated sound from the basic
sound to a chord. (The sound more nearly
approximates the chord as the adjustment
÷
The MIX dial can be used to adjust the
levels of the ring + reverb and original
sounds.
÷
Frequency
Frequency
5. ZIP effect
approaches the [MAX] setting.)
The Jog dial is used to change the pitch.
÷
The CHARACTER dial can be used to
change chords codes. Selectable codes
include Minor (MIN), Minor7, 7, Major
(center position), Major7, Sus4, and Add9
(MAX).
Up (about 1 octave)
Frequency
’
Original
Pitch
÷
÷
The CHARACTER dial can be used to
adjust the reverb effect.
sound
‘
Down
(about 15 octaves)
FWD
REV
Reverb
Wah block
Vocoder
block
block
Jog dial
The MIX dial can be used to adjust the
levels of the wah + reverb sound and the
original sound.
÷
The MIX dial can be used to adjust the
levels of the vocoder and original sounds.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECTS (Effect Parameters)
Effect Parameters
Beat effect
Parameter 0
(TIME)
Parameter 1
(DEPTH)
Parameter 2
(CHARACTER)
Parameter 3
Comments
(MIX)
Feedback filter
(Amount of
Feedback
BPM MODE
DELAY
1~16000 [ms]
1~16000 [ms]*
1~16000 [ms]
1~16000 [ms]*
MIX
MIX
MIX
MIX
—
(feedback level)
feedback filter)
TAP filter
(Amount of TAP
delay filter)
TAP gain
(TAP delay level)
RHYTHM MODE
Max 8-TAP
—
Feedback filter
(Amount of
feedback filter)
Feedback
(feedback level)
BPM MODE
ECHO
TAP filter
(Amount of TAP
delay filter)
TAP gain
(TAP delay level)
RHYTHM MODE
Max 8-TAP
Feedback
Pitch
BPM MODE
PITCH
1~16000 [ms]
1~16000 [ms]*
(feedback level)
(delay sound pitch)
MIX
MIX
—
ECHO
TAP gain
(TAP delay level)
TAP Pitch
(TAP delay sound pitch)
RHYTHM MODE
Max 4-TAP
Phase
(L/R-ch phase
difference)
Sound cutoff
BPM MODE
TRANS
10~16000 [ms]
10~16000 [ms]*
MIX
MIX
—
(amount removed)
Phase
(L/R-ch phase
difference)
Sound cutoff
(amount removed)
RHYTHM MODE
Max 8-TAP
LFO pattern
BPM MODE
FLANGER
10~32000 [ms]
10~32000 [ms]*
10~32000 [ms]
10~32000 [ms]*
10~32000 [ms]
10~32000 [ms]*
Resonance
Resonance
Resonance
Resonance
Resonance
Resonance
MIX
MIX
MIX
MIX
MIX
MIX
—
(change cyclic effect)
LFO pattern
(change cyclic effect)
RHYTHM MODE
Max 8-TAP
—
LFO pattern
(change cyclic effect)
BPM MODE
FILTER
LFO pattern
(change cyclic effect)
RHYTHM MODE
Max 8-TAP
—
LFO pattern
(change cyclic effect)
BPM MODE
PHASER
LFO pattern
(change cyclic effect)
RHYTHM MODE
Max 8-TAP
*
The effect time display in the rhythm mode shows the total time from the beginning to end of TAP
input. For this reason, the noted MIN time may be somewhat different from the effect time display.
Digital Jog Break
Parameter 0
(JOG)
Parameter 1
(DEPTH)
Parameter 2
(CHARACTER)
Parameter 3
(MIX)
Comments
Delay time
Reverb
Resonance
Resonance
MIX
MIX
MIX
MIX
MIX
MIX
—
—
—
—
—
—
JET
WAH
(amount of delay)
(reverberation effect)
Frequency
(filter frequency)
Reverb
(reverberation effect)
Frequency
(filter coefficient)
Reverb
(reverberation effect)
Resonance
Amplitude
PHASE SHIFTER
RING
Frequency
Reverb
(sine wave frequency) (sine-wave amplitude) (reverberation effect)
Pitch
(Scale)
Step
(ScaleÔLinear)
Reverb
(reverberation effect)
ZIP
Vowel
(vowel sound)
Reverb
(reverberation effect)
Resonance
HUMANIZER
Oscillator frequency
(internally generated
sound frequency)
Chord MIX
(chord MIX ratio)
Chord
MIX
—
VOCODER
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE (CONTROLS AND FUNCTIONS)
CONTROLS AND FUNCTIONS
1
2
3
4
5
6
7
8
9
10
Control Panel
11
12
13
41
14
15
16
17
18
40
39
38
37
36
35
34
19
20
21
22
23 24
25 26 27 28 29
30 31 32
33
1 INPUT LEVEL dial
5 METER MODE/MIDI SNAP button
Use to adjust the input level. Adjustment range is –∞ to
[Use to switch the function of the level meter display.]
Each time the button is pressed, the level meter display
switches between input and output monaural display,
input stereo display, and output stereo display.
[MIDI Snapshot Mode]
+9dB with analog inputs, and –∞ to 0dB with digital inputs.
2 SIGNAL FLOW switch
Use to select the order of signal flow between beat effect
and digital jog break sections.
When this button is held depressed with the MIDI mode set
to [TRANSMIT], a snapshot will be sent to the external MIDI
component.
JOG = BEAT:
Signals travel through the digital jog break section before
passing to the beat effect section.
BEAT = JOG:
6 Level meter mode display (INPUT, OUTPUT, L, R)
Input and output monaural display:
Both [INPUT] and [OUTPUT] indicators light.
Input stereo display:
Signals travel through the beat effect section before
passing to the digital jog break section.
[INPUT] and [L], [R] indicators light.
Output stereo display:
[OUTPUT] and [L], [R] indicators light.
3 Foot switch mode selector (FOOT SW)
Use to select which function is controlled (ON/OFF) by an
attached foot switch (pedal switch).
BEAT:
Attached foot switch controls beat effect function (ON/
OFF).
7 Level meter display
JOG:
8 MIDI START/CH SET button / indicator
[MIDI START]
Attached foot switch controls digital jog break function
(ON/OFF).
BOTH:
If this button is pressed when MIDI mode is set to
[TRANSMIT], the MIDI start/stop signal is output.
Lights steadily with START, and goes out with STOP.
[MIDI channel setting (CH SET)]
Attached foot switch controls both beat effect function and
digital jog break function (ON/OFF).
If this button is held depressed when MIDI mode is set to
[TRANSMIT] or [RECEIVE], the MIDI indicator flashes and
the MIDI setting mode is enabled.
4 MIDI mode select switch
Select MIDI communication between computer and other
instruments, etc.
TRANSMIT:
Acts as MIDI controller
RECEIVE:
Effector can be controlled by MIDI signals.
OFF:
Acts as effector (communication OFF)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE (CONTROLS AND FUNCTIONS)
9 BYPASS button / indicator
20 Beat select buttons / indicators
When this button is set to ON, the audio input connector
signals are fed directly to the output connectors, bypassing
the effector circuits.
(1/8, 1/4, 1/2, 3/4, 1/1, 2/1, 4/1, 8/1)
[During BPM mode]
When a BPM is measured automatically or input manually,
the beat select button [1/1] is selected by default. The effect
is synchronized automatically to the BPM, and the
corresponding effect time is displayed.
When the audio input/output connectors are connected
directly in this way, the indicator flashes.
If a beat select button is then pressed, the effect is newly
synchronized to the corresponding multiple of the BPM (1/
8, 1/4, 1/2, 3/4, etc.), thus allowing one-touch change of the
BPM synchronization multiple. In turn, the selected beat
select button lights, thus showing to what multiple of the
actual BPM the effect is synchronized, as well as the
multiple of the time parameter.
10 EFFECT OUT LEV. dial
When effects are set to ON, this dial can be used to control
the effect output level. Adjustment range is –∞ to +6dB.
Beat Effect section
11 BPM COUNTER display
[During RHYTHM mode]
Displays the beats-per-minute of the input source, or the
TAP input. The indicator flashes during automatic BPM
calculation. When power is first turned on, the counter will
flash [120 BPM].
When the rhythm input with the TAP button is established,
[1/1] is selected and a multiple of the rhythm can be
selected with the beat select buttons.
21 Beat effect beat-interval indicators
The indicators light to show the period of the effect time.
12 EFFECT TIME display
Displays actual effect time.
When power is first turned on, defaults to [500 mSec].
22 Beat effect TIME/BPM dial
When rotated the effect time selected with the beat select
buttons can be changed as desired.
If the dial is rotated while depressing the TAP button, the
BPM can be set as desired (BPM manual input).
13 BPM measurement mode display
(AUTO, MIDI, TAP).
Displays the BPM measurement mode.
14 MIDI display
23 BPM MODE button / indicator
Lights when handling MIDI data.
Use to turn BPM mode ON, and to select tempo
measurement mode (AUTO/MIDI/TAP). During BPM mode,
the button lights.
15 RHYTHM TAP display
Displays the tap count input in the rhythm mode.
If the TAP button is pressed (tapped) during BPM mode,
the mode switches to manual BPM measurement mode.
When power is first turned, the mode defaults to AUTO
measurement mode.
16 Beat effect select button / indicator
(DELAY, ECHO, PITCH ECHO, TRANS, FLANGER,
FILTER, PHASER).
Use to select the beat effect. All buttons light, and selected
effect button flashes.
24 TAP/SHIFT button / indicator
[During BPM mode]
When power is turned ON, DELAY flashes.
When this button is tapped, the BPM manual measurement
mode is selected, and the interval between two taps
(maximum interval 2 seconds) is measured; the
corresponding EFFECT TIME and BPM count is displayed,
and the beat select button [1/1] is selected.
If the TIME/BPM dial is rotated while pressing this button,
the BPM can be adjusted to an optional value (BPM manual
input).
17 BEAT EFFECTS indicator
Lights when beat effects are ON.
18 BEAT EFFECTS lever switch (OFF/ON/ON-LOCK)
Pull the lever toward you [ON] to output beat-effected
sounds.
In the middle position beat effects are [OFF]; push the lever
away from you to lock the lever in the [ON/LOCK] position
(effects are locked ON). When pulled to the [ON] position,
beat effects are output only while the lever is held; when
your finger is released, the lever returns to middle [OFF]
position.
[During RHYTHM mode]
When this button is tapped, the rhythm is input (maximum
tap interval 2 seconds, up to maximum rhythm count 8).
The beat select button [1/1] is selected.
[Tap indicator]
Lights during normal use; goes out only when TAP is
pressed.
19 EFFECT FREQUENCY select buttons (LOW/MID/HI)
Use to select the frequency band of the sounds to which
beat effects will be applied. The button of the selected band
will light.
25 Rhythm REC button
Clears the currently input rhythm and allows input of a new
rhythm.
When power is first turned ON, all three of the ranges LOW,
MID, and HI are selected. If all three range buttons are OFF,
no beat effects will be applied to sounds.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE (CONTROLS AND FUNCTIONS)
26 RHYTHM MODE button / indicator
When this button is pressed, the RHYTHM mode is
selected, and the button lights.
36 Jog memory LOOP play button / indicator
If the button is pressed while the button indicator is lighted,
the parameter change previously recorded in memory in
response to the Jog dial movement is reproduced (played
back repeatedly).
Press again to end Jog memory loop play.
Indicator lights when the jog operation is stored in
memory. Indicator flashes during jog memory loop play
(playback).
27 Beat effect DEPTH dial
Allows adjustment of effect feedback and timing
parameters in accordance with the amount of rotation (see
page 13).
28 Beat effect CHARACTER dial
Allows adjustment of parameters other than those set with
the beat effect DEPTH dial (see page 13).
37 Jog HOLD button / indicator
When this button is pressed so that its indicator lights, the
effect produced when rotating the Jog dial is maintained
even if you remove your hand from the dial (when the hold
function is OFF, the effect returns to normal if your hand is
removed from the dial). When power is first turned on, the
button defaults to jog hold OFF (indicator is off).
29 Beat effect MIX dial
Rotate to adjust the mixing balance of original and effect
sounds. When rotated fully to the [ORIGINAL] side, the
original (un-effected) sound will be output; as the dial is
rotated toward the [EFFECT] side, the effect sound is
amplified and the original sound decreases.
38 DIGITAL JOG BREAK effect lever switch
(OFF/ON/ON-LOCK)
Pull the lever toward you [ON] to output effected sounds.
In the middle position effects are [OFF]; push the lever
away from you to lock the lever in the [ON/LOCK] position
(effects are locked ON). When pulled to the [ON] position,
effects are output only while the lever is held; when your
finger is released, the lever returns to middle [OFF]
position.
Digital Jog Break section
30 Digital jog break effect MIX dial
Rotate to adjust the mixing balance of original and effect
sounds. When rotated fully to the [ORIGINAL] side, the
original (un-effected) sound will be output; as the dial is
rotated toward the [EFFECT] side, the effect sound is
amplified and the original sound decreases.
39 DIGITAL JOG BREAK effect indicator
Lights when digital jog break effect is ON.
31 Digital jog break effect CHARACTER dial
Allows adjustment of parameters other than those set with
the digital jog break DEPTH dial (see page 13).
40 Digital jog break effect selector buttons /
indicators (JET, WAH, PHASE SHIFTER, RING,
ZIP, HUMANIZER, VOCODER)
Press to select a desired digital jog break effect. All the
buttons light, and the select effect button flashes.
When power is turned ON, JET flashes.
32 Digital jog break DEPTH dial
Allows adjustment of effect feedback and timing
parameters in accordance with the amount of rotation (see
page 13).
41 DIGITAL JOG BREAK METER
During operation of the Jog dial, and during jog memory
play, this meter lights to display the corresponding
movement.
33 Jog dial
Effect parameters change in response to the rotation of the
dial.
34 Jog memory button (M)
If the Jog dial is rotated while holding this button
depressed, the parameter change in response to the
movement is recorded to memory, to a maximum 8
seconds. Recording to memory is not possible during jog
memory play.
35 Jog memory SINGLE play button / indicator
If the button is pressed while the button indicator is lighted,
the parameter change previously recorded in memory in
response to the Jog dial movement is reproduced (played
back) one time only.
Indicator lights when the jog operation is stored in
memory. Indicator flashes during jog memory single play
(playback).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
OPERATIONS
INPUT LEVEL
FOOT SW
MIDI (TRANSMIT/RECEIVE/OFF)
EFFECT OUT LEV.
SIGNAL FLOW
METER MODE
BYPASS
¶ When set to the [BEAT] position the foot switch operates to
Adjusting Input Level
turn beat effects ON/OFF.
*
Use a commercially available switching-type foot switch
with 6.3 mm monaural phone plug.
Adjust the input level so that the sound is not distorted due
to an excessive input level.
7 Input signals to the input connectors, and rotate the
INPUT LEVEL dial to adjust the level.
Selecting the Level Meter Display
¶ Use the METER MODE button to select “input stereo
display” (INPUT, L, R indicators light).
¶ If the proper adjustment cannot be obtained without
rotating the INPUT LEVEL dial to its extreme [MIN] or
[MAX] positions, try changing the position of the rear-panel
IN&OUT LEVEL switch (–10dB / +4dB).
This unit’s level meter can be set to display the desired
mode.
7 Press the METER MODE button to select the desired
mode.
¶ Each time the METER MODE button is pressed, the display
switches alternately as follows:
[INPUT] and [OUTPUT] light:
= Input and output level are displayed in monaural.
[INPUT] and [L], [R] light:
= Input level is displayed in stereo.
[OUTPUT] and [L], [R] light:
Adjusting Effect Output Level
Adjusts the sound level of the effect applied to the input
sound signal by the beat effect and the digital jog break.
7 Input signals to the input connectors, and rotate the
EFFECT OUT LEV. dial to adjust the effect output level.
¶ Use the METER MODE button to select “output stereo
display” (OUTPUT, L, R indicators light).
= Output level is displayed in stereo.
Digital Link Function
Fader Effect Function
¶
When both the BEAT EFFECTS lever switch and the DIGITAL
JOG BREAK lever switch are set to [OFF], the output level is
not changed by turning the EFFECT OUT LEV. dial.
When the accessory digital link cable is used to connect
this unit to a DJ mixer (DJM-1000) with digital link support,
send/return connections are completed by a single digital
connection, thus enabling fader effect functions that allow
the DJ mixer’s fader to be used to perform digital jog break.
Selecting Signal Flow
Select the order in which signal processing occurs (beat
effect or digital jog break)
7 Use the SIGNAL FLOW switch to select the signal
Bypass Function
processing order:
This function allows signals to be output directly, without
passing through the effects processing circuitry.
7 Press the BYPASS button to make a direct link between
input and output.
¶ When set to the [JOG=BEAT] position, signals are
processed for digital jog break effects first, followed by beat
effects .
¶ When set to the [BEAT=JOG] position, signals are
processed for beat effects first, followed by digital jog break
effects.
¶ When the BYPASS button is pressed, the button flashes and
input signals are output directly, without passing through
the effector circuitry.
¶ When the BYPASS button is flashed, the unit’s controls will
have no effect on the input signals.
Selecting Foot Switch Operation
This effector allows connection of an optional foot switch
(pedal switch) for ON/OFF control of beat effects and digital
jog break effects. Use the foot switch to select the way in
which the foot switch operates.
7 Set the FOOT SW switch to the desired operating
position:
¶ When set to the [JOG] position, the foot switch operates to
turn digital jog break effects ON/OFF.
¶ When set to the [BOTH] position, the foot switch operates to
turn both digital jog break effects and beat effects ON/OFF.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS (Beat Effects [BPM mode])
2. Use the beat effect select buttons to select the desired
effect.
2) DELAY, ECHO, PITCH ECHO,TRANS,
FLANGER, FILTER, PHASER
¶ Select from DELAY, ECHO, PITCH ECHO, TRANS,
FLANGER, FILTER, or PHASER.
5) BEAT EFFECTS
(beat effect select)
¶ The selected effect button flashes.
¶ See pages 10, 11 regarding each effect.
3) EFFECT
FREQUENCY
LOW, MID, HI
3. Use the EFFECT FREQUENCY buttons (LOW, MID, HI) to
select the band to which the effect is to be applied.
¶ When a button is pressed, the button’s indicator will light.
¶ Each time a button is pressed, it alternates ON/OFF.
DEPTH
CHARACTER
4. Press one beat select button to select the beat with
which the effect is to be synchronized.
¶ Select from 1/8, 1/4, 1/2, 3/4, 1/1, 2/1, 4/1, or 8/1.
¶ The selected beat button lights.
¶ When a beat select button is pressed, the corresponding
effect time is automatically set.
MIX
Example: when BPM is 120,
1/1 = 500 ms
3/4 = 375 ms
1/2 = 250 ms
1) BPM MODE TAP
TIME
4) 1/8, 1/4, 1/2, 3/4, 1/1, 2/1, 4/1, 8/1
¶ When the beat select button is pressed and the TAP button
is held down, BPM is automatically set from the effect time.
(beat select)
Manual Input of Effect Time Using the TIME Dial
Normally, the effect time is automatically set when a
beat select button is pressed. However, the effect time
can be set as desired using the TIME dial.
¶ When the effect time is changed, the beat select button
lights for the beat automatically set in correspondence to
the new effect time.
Beat Effects [BPM mode]
Since the beat effect time of the beat effect [BPM mode] can
be synchronized in real-time with the BPM (beats per
minute), you can easily generate effects in time with the
rhythm of a live performance.
5. Pull the BEAT EFFECTS lever switch to ON to appy the
effect.
1. Press the BPM MODE button to select the BPM (beats-
per-minute) measurement mode.
When pushed away from you to the [ON/LOCK] position:
The switch is locked on, so that the effect continues to be
applied even if you remove your hand from the lever. To stop
the effect, return the lever to the middle position [OFF].
When pulled toward you to the [ON] position:
AUTO: BPM is measured automatically from the input music
source.
MIDI: BPM is measured automatically based on the MIDI timing
clock.
TAP: BPM is input manually by tapping on the TAP button.
¶ When power is first turned ON, the mode defaults to AUTO.
¶ The selected mode is shown by the BPM mode indicator.
¶ In the event the input signal cannot be counted properly,
the BPM COUNTER flashes.
The effect is applied only while the lever is pulled to the [ON]
position; when the lever is released, it returns automatically to
the middle [OFF] position. Use this function when you wish to
alternate rapidly between ON and OFF.
¶ The measurement range in the AUTO mode is 70-180 BPM.
Correct measurement may not be possible depending on
the music track; in this event, input the tempo manually
using the TAP mode.
DEPTH dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 1 in
response to DEPTH dial rotation, see pages 10, 11, 13.
[Manual BPM input using the TAP button]
When the TAP button is tapped two or more times in
time with the beat (quarter notes), the average value
of the intervals is used to set BPM.
¶ When BPM is set to AUTO or MIDI mode, pressing the TAP
button changes the BPM measuring mode to the TAP mode,
and the unit measures the intervals at which the TAP button
is struck.
CHARACTER dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 2 in
response to CHARACTER dial rotation, see pages 10, 11, 13.
MIX dial
Use to adjust the mixing balance of original and effect sounds. Set
to the center indent position for standard effect sounds.
¶ When BPM is set with the TAP button, the beat select
button [1/1] is selected and the time of 1 beat (quarter
notes) is set to the effect time.
[Manual BPM input using the TIME dial]
BPM can be directly set by turning the TIME dial when
the TAP button is held down.
¶ BPM can be set in 0.1 increments by pressing the BPM MODE
button and turning the TIME dial while holding down the TAP
button. Only decimal values are shown at this time.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations (Beat Effects [RHYTHM mode])
6. Select one of the beat select buttons to establish the
overall time for the input rhythm.
2) DELAY, ECHO, PITCH ECHO,TRANS,
FLANGER, FILTER, PHASER
(beat effect select)
¶ The overall time for the input rhythm will be multiplied in
response to the selected button.
7) BEAT EFFECTS
¶ Select from 1/8, 1/4, 1/2, 3/4, 1/1, 2/1, 4/1, or 8/1.
¶ The selected beat button lights.
3) EFFECT
FREQUENCY
LOW, MID, HI
7. Pull the BEAT EFFECTS lever switch to ON to appy the
effect.
DEPTH
When pushed away from you to the [ON/LOCK] position:
The switch is locked on, so that the effect continues to be
applied even if you remove your hand from the lever. To stop
the effect, return the lever to the middle position [OFF].
When pulled toward you to the [ON] position:
CHARACTER
The effect is applied only while the lever is pulled to the [ON]
position; when the lever is released, it returns automatically to
the middle [OFF] position. Use this function when you wish to
alternate rapidly between ON and OFF.
¶ If the Rhythm REC button is pressed during the rhythm
mode, the input rhythm will be cleared and rhythm input
mode is once again enabled.
MIX
BPM MODE
5) TAP 1) RHYTHM MODE
TIME
DEPTH dial
4) Rhythm REC
6) 1/8, 1/4, 1/2, 3/4, 1/1, 2/1, 4/1, 8/1
(beat select)
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 1 in
response to DEPTH dial rotation, see pages 10, 11, 13.
Beat Effects [RHYTHM mode]
CHARACTER dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 2 in
response to CHARACTER dial rotation, see pages 10, 11, 13.
The beat effects [RHYTHM mode] function allows you to
create a variety of effects synchronized with your own
input rhythm.
1. Use the RHYTHM MODE button to set to rhythm mode.
¶ The RHYTHM MODE button lights.
MIX dial
Use to adjust the mixing balance of original and effect sounds. Set
to the center indent position for standard effect sounds.
2. Use the beat effect select buttons to select the desired
effect.
¶ Select from DELAY, ECHO, PITCH ECHO, TRANS,
FLANGER, FILTER, or PHASER.
¶ The selected effect button flashes.
¶ See pages 10, 11 regarding each effect.
3. Use the EFFECT FREQUENCY buttons (LOW, MID, HI) to
select the band to which the effect is to be applied.
¶ When a button is pressed, the button’s indicator will light.
¶ Each time a button is pressed, it alternates ON/OFF.
4. Press rhythm REC button to set to REC mode.
¶ The BPM display will indicate “
”.
¶ If no rhythm has been input, the unit will automatically
enter the REC mode in step 1.
5. Input the desired rhythm using the TAP button.
¶ Input taps will be recognized as a tempo when occurring at
intervals of less than 2 seconds. Up to 8 taps can be input.
¶ The counted taps (RHYTHM TAP) will be shown in the
display.
¶ During rhythm input, the beat select button [1/1] will be
selected.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS (Digital Jog Break)
MIX dial
Use to adjust the mixing balance of original and effect sounds. Set
to the center indent position for standard effect sounds.
1) JET, WAH, PHASE SHIFTER,
RING, ZIP, HUMANIZER, VOCODER
(Jog effect select)
2) DIGITAL JOG BREAK
HOLD Function
When the HOLD button is pressed and lit, the effect generated by
the rotation of the Jog dial continues when the dial rotation stops.
DEPTH
Jog Memory
HOLD
Up to 8 seconds of the digital jog break’s jog dial
movement can be stored in memory, and the effect later
played back at a single touch.
CHARACTER
LOOP
SINGLE
1. Use the Jog effect select buttons to select the desired
effect.
MIX
¶ Select from JET, WAH, PHASE SHITER, RING, ZIP,
HUMANIZER, or VOCODER.
¶ The selected Jog effect button flashes.
¶ See page 12 regarding each effect.
Jog memory (M)
Jog dial
2. Set the DIGITAL JOG BREAK lever switch to ON to
monitor the effect.
3. Turn the Jog dial while holding down the Jog memory
button (M).
Digital Jog Break
Turning the Jog dial while the M button is held down starts
memory storage. Effects are stored continues for 8 seconds or
until the M button is released. The SINGLE or LOOP button
lights.
¶ When an effect has already been stored in memory
(SINGLE button and LOOP button are lighted), if a new
effect is stored in memory, the previously stored contents
will be overwritten and the effect data will be erased.
Since the digital jog break can continuously change the
parameters of each effect generated by rotating the Jog
dial, the effects can be controlled like a musical instrument.
Further, by using the jog memory function, the continuously
changing effect sound can be stored in memory, and later
played back by pressing one of the JOG MEMORY PLAY
buttons (SINGLE or LOOP).
4. Press the SINGLE or LOOP button.
1. Use the Jog effect select buttons to select the desired
effect.
¶ When the SINGLE button is pressed, the button flashes and
the stored effect produced by the jog dial movement is
played back one time.
¶ When the LOOP button is pressed, the button flashes and
the stored effect produced by the jog dial movement is
played back repeatedly. Press the LOOP button once again
to stop the effect playback.
¶ Select from JET, WAH, PHASE SHITER, RING, ZIP,
HUMANIZER, or VOCODER.
¶ The selected Jog effect button flashes.
¶ See page 12 regarding each effect.
2. Set the DIGITAL JOG BREAK lever switch to ON and
turn the Jog dial.
¶ Jog dial operation stored in memory can be reproduced
even when the type of effect is subsequently changed.
[DIGITAL JOG BREAK Lever switch operation]
When pushed away from you to the [ON/LOCK] position:
The switch is locked on, so that the effect continues to be
applied even if you remove your hand from the lever. To stop
the effect, return the lever to the middle position [OFF].
When pulled toward you to the [ON] position:
The effect is applied only while the lever is pulled to the [ON]
position; when the lever is released, it returns automatically to
the middle [OFF] position. Use this function when you wish to
alternate rapidly between ON and OFF.
¶ Parameter changes caused by rotating the Jog dial are
indicated on the DIGITAL JOG BREAK METER.
DEPTH dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 1 in
response to DEPTH dial rotation, see pages 12, 13.
CHARACTER dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 2 in
response to CHARACTER dial rotation, see pages 12, 13.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI SETTINGS
MIDI SETTINGS
MIDI (Musical Instrument Digital Interface) is a standard protocol designed to allow exchange of information between electronic
instruments and/or computers. A MIDI cable is used to connect two appliances equipped with MIDI connectors, thus allowing data to be
exchanged between the two appliances. The EFX-1000 uses MIDI to send and receive operation and BPM data (timing clock).
Synchronizing an external
To synchronize beat effects to
external sequencer, or use an
external sequencer to operate the
EFX-1000
sequencer to an audio signal, or
using EFX-1000 operation data to
operate an external sequencer
DJ CD player
MIDI sequencer
MIDI sequencer
OUT OUT
IN
OUT
BPM
=120
Audio
BPM
=120
Audio
MIDI
BPM
=120
MIDI
MIDI START/
MIDI TRANSMIT/
RECEIVE/OFF
MIDI START/
CH SET
MIDI TRANSMIT/
RECEIVE/OFF
IN
IN
CH SET
IN
OUT
TIME
TAP
EFX-1000
TIME
TAP
EFX-1000
1. Use a commercially available MIDI cable to connect the
EFX-1000’s MIDI OUT connector and the MIDI
sequencer’s MIDI IN connector.
1. Use a commercially available MIDI cable to connect the
MIDI sequencer’s MIDI OUT connector to the EFX-1000’s
MIDI IN connector.
¶ The MIDI sequencer’s sync mode should be set to slave.
¶ MIDI sequencers which do not support MIDI timing clock
cannot be synchronized.
¶ Adjust controls for optimum instrument input/output levels.
¶ Set all effect switches to OFF.
¶ Set BYPASS switch to OFF.
2. Set MIDI switch to [TRANSMIT] position.
¶ Sync cannot be performed in the case of tracks whose BPM
values cannot be measured stably.
¶ Timing clock is also output for BPM values set by using the
TAP mode.
3. Press the MIDI START/CH SET button.
¶ MIDI timing clock output range is 40-250 BPM.
2. Set the MIDI switch to the [RECEIVE] position.
¶ The timing clock based on the BPM counted and displayed
by this unit is output from the MIDI OUT connector.
3. Start the MIDI sequencer.
¶ Even during use of sequencer control, the EFX-1000 can be
controlled directly if desired, but depending on the volume,
the set parameter values may jump at the instant an
operation is performed, so caution is needed.
¶ The range that the MIDI timing clock can accept is 40-250
BPM.
[Setting TRANSMIT MIDI channel]
The TRANSMIT channel can be set and recorded in memory
separately from the RECEIVE channel.
[Setting the RECEIVE MIDI channel]
The RECEIVE channel can be set and recorded in memory
separately from the TRANSMIT channel.
1. Set MIDI switch to [RECEIVE] position.
2. In this condition, hold the MIDI START/CH SET button
depressed.
¶ The MIDI indicator will flash and the setting mode will be
enabled.
3. Rotate the TIME dial to select the MIDI channel, then
press the TAP button to confirm.
1. Set MIDI switch to [TRANSMIT] position.
2. In this condition, hold the MIDI START/CH SET button
depressed.
¶ The MIDI indicator will flash and the setting mode will be
enabled.
3. Rotate the TIME dial to select MIDI channel.
4. Press the MIDI START/CH SET button.
¶ The MIDI channel will be recorded, and the unit will leave
the setting mode.
NOTE:
It may not be possible to set BPM correctly with some tracks.
NOTE:
If the MIDI sequencer’s BPM is set in 0.1 units, it may not match the
BPM display on the EFX-1000.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI SETTINGS
MIDI Implementation Chart
Function
Transmit
Receive
Comments
Basic channel: When power ON
Settable range
1-16
1-16
1-16
1-16
Stored in memory
When power ON
Mode 3
Mode 3
Mode:
Message
✕
✕
Replacement
Note number:
Velocity:
✕
✕
✕
✕
Sound range
Note ON
Note OFF
✕
✕
✕
✕
After touch:
Pitch Bender:
By Key
By Channel
✕
✕
✕
✕
✕
✕
12, 44
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
Beat select time parameter (MSB, LSB)
Time parameter (MSB, LSB)
JOG parameter (MSB, LSB)
Rhythm parameter 1 (MSB, LSB)
Effect ON/OFF
13, 45
16, 48
17, 49
64
66
67
69
80
81
82
83
91
Frequency select
Control change:
Rhythm parameter 2
Beat Operation Mode
VR parameter 1
VR parameter 2
VR parameter 3
VR parameter 4
VR parameter 5
VR parameter 6
92
Program change: setting range
Exclusive:
‡
‡
✕
✕
Song position
Common: Song select
Tune
✕
✕
✕
✕
✕
✕
Real time: Clock
Command
‡
‡
‡
✕
Transmit: start/stop
Local ON/OFF
✕
✕
✕
✕
✕
✕
✕
✕
Other:
All Note/OFF
Active sensing
Reset
Comments:
Mode 1: Omni, ON, Poly
Mode 3: Omni, OFF, Poly
Mode 2: Omni, ON, Mono
Mode 4: Omni, OFF, Mono
‡: Yes
✕: No
Control Change (CC) Table
Message
(Command)
Function
EFX-1000 Operation
Format (Hex)
Comments
Signal flow change
Beat effect select
Effect type
ProgramChange
Cn pc
See program change below.
switching
Digital jog break
Effect select
Sets effect ON/OFF.
b: Effect ON/OFF (ON = 1)
Bit0 JOG
Beat effect (ON/OFF)
Bit1 BEAT
Effect ON/OFF
Hold 1
Bn 40 0b
Digital jog break
Effect (ON/OFF)
MSB
LSB
0
0
0
0
0
0
BEAT JOG
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI SETTINGS
Message
(Command)
Function
EFX-1000 Operation
Format (Hex)
Comments
Sets effect time.
Setting range (unit: mSec)
DELAY, ECHO, PITCH ECHO: 1-16000
Beat select
Effect Control 1
Bn 0c MSB
TRANS:
10-16000
Bn 2c LSB
FLANGER, FILTER, PHASER: 5-16000
When 5-16000 are transmitted for FLANGER,
FILTER, or PHASER, EFX-1000 internally
multiplies value by x2, so as to operate at 10-
32000.
* On receive side, search is performed for
beginning of effect cycle.
Effect time
operation
Sets effect time.
Setting range (unit: mSec)
DELAY, ECHO, PITCH ECHO: 1-16000
TIME dial
Effect Control 2
Bn 0d MSB
Bn 2d LSB
TRANS:
10-16000
FLANGER, FILTER, PHASER: 5-16000
When 5-16000 are transmitted for FLANGER,
FILTER, or PHASER, EFX-1000 internally
multiplies value by x2, so as to operate at 10-
32000.
* On receive side, search is not performed
for beginning of effect cycle.
Sets frequency range subjected to effect
b: frequency range (ON = 1)
Bit0 LOW
Bit1 MID
Bit2 HI
Effect frequency select
sostenuto
Bn 42 0b
MSB
0
LSB
HI MID LOW
0
0
0
0
Rhythm TAP
(rhythm time)
General Purpose
Controller 2
Bn 11 MSB
Bn 31 LSB
Sets tap time interval for rhythm effect.
Setting range (unit: mSec)
1-2000
Beat operation
Rhythm TAP
(rhythm no.)
Sets tap number for rhythm effect.
Setting range: 1-8
soft pedal
hold 2
Bn 43 dd
Bn 45 dd
Changes Beat operating mode.
1=BPM mode
BPM mode SW
Rhythm mode SW
Rhythm REC
2=Rhythm mode
During rhythm mode, if rhythm mode is set
again, the recorded rhythm effect will be
canceled and new rhythm data can be input.
Sets jog dial movement.
Jog dial
General Purpose
Controller 1
Bn 10 MSB
Bn 30 LSB
Setting range: 0-2160
Jog center position is considered 1080; when
dial is rotated clockwise, changes to
maximum 2160; when dial is rotated
counterclockwise, changes to minimum 0.
Jog operation
Beat volume
Sets beat DEPTH value.
Setting range: 0-127
Beat effect DEPTH
Beat effect CHARACTER
Beat effect MIX
Effect 1 Depth
Bn 5B dd
Bn 50 dd
Bn 51 dd
Bn 5C dd
Bn 52 dd
Bn 53 dd
General Purpose
Controller 5
Sets beat CHARACTER value.
Setting range: 0-127
General Purpose
Controller 6
Sets beat MIX value.
Setting range: 0-127
Sets Jog DEPTH value.
Setting range: 0-127
Digital jog break DEPTH Effect 2 Depth
Digital jog break
CHARACTER
General Purpose
Controller 7
Sets jog CHARACTER value.
Setting range: 0-127
Jog volume
General Purpose
Controller 8
Sets jog MIX value.
Setting range: 0-127
Digital jog break MIX
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI SETTINGS
Program Change
MSB
LSB
¶ SIGNAL FLOW
0 = BEAT EFFECTS = JOG BREAK
1 = JOG BREAK = BEAT EFFECTS
SIGNAL
0
FLOW BEAT2 BEAT1 BEAT0 JOG2 JOG1 JOG0
¶ BEAT EFFECTS
¶ JOG BREAK
BEAT2
BEAT1
BEAT0
JOG2
JOG1
JOG0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
DELAY
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
JET
ECHO
WAH
PITCH ECHO
TRANS
PHASE SHIFTER
RING
FLANGER
FILTER
ZIP
HUMANIZER
VOCODER
PHASER
Use general purpose 8 for setting filters
About Rhythm Effects
(Example shown is 3 rhythms)
During TRANSMIT:
Each time rhythm TAP is struck, data is transmitted in the order rhythm parameter 2 (rhythm No.) and rhythm parameter 1
(rhythm time).
Effector operation
RHYTHM MODE button TAP
TAP
TAP
TAP
time 1
time 2
time 3
MIDI data
Beat section
Rhythm mode
Rhythm No. 1
time 1
Rhythm No. 2
time 2
Rhythm No. 3
time 3
During RECEIVE:
¶ During beat effect, if beat operation mode (rhythm mode) is received, the rhythm effect function is enabled.
Thereafter, if the first time rhythm No. 1, time 1, rhythm No. 2, time 2, rhythm No. 3, time 3 are transmitted in that order,
the effector continues to operate in response to the received rhythm.
¶ During rhythm effect, if the beat operation mode (BPM mode) is transmitted, the function returns to beat effect.
Snapshot
METER MODE/MIDI SNAP
Once the effector is set to a target value, a snapshot of that
state can be taken. When snapshot is used, all commands
for control change are transmitted at once.
When setting [TRANSMIT], hold the METER MODE/MIDI
SNAP button depressed to transmit the snapshot. When
this is done the MIDI indicator will flash.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER (TROUBLESHOOTING)
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this
component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the
other electrical appliances also in use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service
center.
Symptom
Probably cause
Remedy
Connect power cord to outlet.
Connect properly.
No power
÷
÷
Power cord isn’t connected.
÷
÷
No sound, or too low
Connection cords are loose or aren’t con-
nected properly.
÷
÷
Connector terminals and plugs are dirty.
Input level is set too low.
÷
÷
Wipe away dirt and soil.
Rotate INPUT LEVEL dial toward right
([MAX] direction).
÷
÷
Try setting IN&OUT LEVEL switch to the
opposite position.
Rotate EFFECT OUT LEV. dial toward right
([MAX] direction).
÷
÷
Effect output level is set too low.
Analog inputs aren’t output
A digital or EFX LINK input is connected.
When analog and digital inputs are connected
simultaneously, the digital input is given
priority.
The DJ mixer (DJM-1000) connected by EFX
LINK has its effecter link set to ON (EFX LINK).
÷
Cancel the EFX LINK, and disconnect any
digital input with priority over analog
inputs.
The order of priority of inputs is:
EFX LINK > Digital input > Analog input.
÷
÷
Digital signals aren’t output.
EFX LINK is connected to DJ mixer (DJM-
1000) via digital link cable.
÷
If EFX LINK is connected to DJ mixer (DJM-
1000) via digital link cable, ordinary digital
signals are not output.
Disconnect the digital link cable.
Set the digital output fs to match the
connected component.
÷
÷
The digital output fs setting does not match
the connected component.
÷
÷
When set to BYPASS, analog
signals aren’t output.
No analog inputs are connected.
Use analog signals for input. Or use digital
output. Outputs when BYPASS is selected
are as follows:
Even if a digital input or EFX LINK is
connected, analog inputs are output as analog
during BYPASS mode.
Input
connection
conditions
Analog output Digital output
Analog only Analog source Analog source
Digital only
(no output)
Digital source
Analog &
digital
Analog source Digital source
Effect sounds aren’t applied.
÷
÷
÷
÷
÷
The lever switch is set to [OFF].
MIX dial is set to [MIN].
÷
÷
÷
÷
÷
Either hold lever switch in [ON] position, or
set to [ON/LOCK].
Rotate MIX dial toward the right ([MAX]
direction).
Rotate DEPTH dial toward the right ([MAX]
direction).
Rotate EFFECT OUT LEV. dial toward the
right ([MAX] direction).
DEPTH dial is set to [MIN].
EFFECT OUT LEV. dial is set to [MIN].
BYPASS button is ON.
If BYPASS indicator is flashed, no effects
will be output. Press BYPASS so that the
indicator goes out.
÷
EFFECT FREQUENCY indicators (HI, MID,
LOW) are all off (during use of TRANS,
FLANGER, FILTER, or PHASER effects).
÷
If EFFECT FREQUENCY indicators are all off,
only the original sound will be output. Press
the button corresponding to the frequency
band to which you wish to apply effects (the
button’s indicator will light).
÷
÷
Some combinations of effects may have weak
results. Particularly, some combinations of
beat effects and digital jog break may sound
weak.
÷
÷
Try setting SIGNAL FLOW switch to the
opposite position (reverse order of signal
processing for beat effects and digital jog
break).
No effect sound is heard when
beat effects are applied.
EFFECT FREQUENCY indicators (HI, MID, LOW)
are all off (during use of DELAY, ECHO, PITCH
ECHO effects).
If EFFECT FREQUENCY indicators are all off,
no effect sound will be output. Press the
button corresponding to the frequency band
to which you wish to apply effects (the
button’s indicator will light).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER (TROUBLESHOOTING)
Symptom
Probably cause
Remedy
When a foot switch is connected,
effects are applied even without
pressing the foot switch.
÷
÷
Foot switch’s logic is reversed (the effector
applies effects when the foot switch is
depressed for LOW level).
÷
Use a foot switch with logic matching that
of the effector.
Effect sounds are distorted.
Input level is too high.
÷
÷
÷
÷
Rotate INPUT LEVEL dial toward left ([MIN]
direction).
Try setting IN&OUT LEVEL switch to the
opposite position.
Rotate EFFECT OUT LEV. dial toward left
([MIN] direction).
Rotate DEPTH dial toward left ([MIN]
direction).
÷
÷
Effect output level is too high.
Effect settings are too high (When the DEPTH
dial is set near its [MAX] position, it may have
the effect of raising the volume level.)
Can’t use EFX LINK function
÷
÷
÷
The digital link cable is not connected.
The connected component is not supported.
The DJ mixer’s settings are incorrect
÷
Connect the digital link cable to a DJ mixer
(with digital link support)
Set the DJ mixer for EFX LINK.
÷
÷
Can’t use the BPM sync function.
÷
÷
DJ mixer is not connected for EFX LINK.
A DJ CD player with digital link support is not
connected to the DJ mixer.
Connect the DJ CD player and DJ mixer via
digital link.
÷
÷
The BPM measurement mode is not set to
[AUTO].
÷
÷
Set the DJ effector’s BPM mode to [AUTO].
Echo sounds are output
continuously
During echo effect, if DEPTH dial is set to
[MAX] and BEAT EFFECTS lever switch is
moved from [ON] to [OFF], the feedback
sound dies not attenuate, producing a hold
delay effect.
Rotate DEPTH dial toward the left ([MIN]
direction).
BPM doesn’t count tempo in
AUTO mode.
BPM count is strange.
÷
÷
Input level is too high, or too low.
÷
÷
Rotate INPUT LEVEL dial so that the input
level meter shows around 0 dB.
Set to manual mode and input (TAP) the
tempo manually (P.18)
Some tracks have tempos that prevent them
from being measured automatically. (Automatic
measurement range is 70-180 BPM).
MIDI sequencer isn’t
synchronized.
÷
÷
The MIDI sequencer’s sync mode is not set to
“slave”.
The connected MIDI sequencer is not
supported.
÷
÷
Set MIDI sequencer’s sync mode to
“slave.”
A MIDI sequencer without MIDI timing
clock cannot be synchronized.
÷ This component may fail to operate properly due effects from static electricity or other causes. In this event, try
disconnecting the power cord and reconnecting it. If this doesn’t solve the problem, consult your dealer or nearest
Pioneer Service Station.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER (SPECIFICATIONS)
SPECIFICATIONS
1. General
3. Input/Output terminals
Audio line input terminal
Power supply ............................................................ AC 120 V, 60 Hz
Power consumption .................................................................... 16 W
Operating temperature ................... +5°C to +35°C (+41°F to +95°F)
Relative humidity ...................... 5% to 85% (without condensation)
Weight ............................................................................ 2.4 kg (5.3 lb)
Maximum external dimensions
RCA pin jacks .................................................................................2
Phone jacks (1/4-inch/6.3 mm in diameter) ................................2
Audio line output terminal
RCA pin jacks .................................................................................2
Phone jacks (1/4-inch/6.3 mm in diameter) ................................2
Digital input terminal
.......................................................... 320 (W) x 234 (D) x 101 (H) mm
12-19/32 (W) x 9-7/32 (D) x 3-31/32 (H) in.
RCA pin jack ...................................................................................1
Digital output terminal
RCA pin jack ...................................................................................1
EFX LINK connector (mini-DIN) ........................................................1
MIDI input terminal (5-pin DIN).........................................................1
MIDI output terminal (5-pin DIN) ......................................................1
2. Audio Unit
Sampling rate............................................................................ 96 kHz
A/D, D/A Resolution .................................................................. 24 bits
Frequency characteristics ......................................... 20 Hz to 22 kHz
S/N ratio ....................................................................................... 83 dB
Distortion ................................................................................... 0.02 %
Headroom .................................................................................... 19 dB
Input level ................................................... –10 dBV / +4 dBu (22 kΩ)
Output level ............................................................. –10 dBV / +4 dBu
(RCA pin jacks: 1 kΩ, Phone jacks: 1 kΩ)
4. Accessories
Operating instructions .......................................................................1
Digital link cable .................................................................................1
Power cord ..........................................................................................1
Warranty ..............................................................................................1
*–10 dBV / +4 dBu is switchable.
NOTE:
Specifications and design are subject to possible modification
without notice.
BLOCK DIAGRAM
RY.
ANALOG BYPASS LINE
ANALOG
OUTPUT
ANALOG
INPUT
DIGITAL BYPASS LINE
D/A
A/D
DSP
JOG
BREAK
BEAT
EFFECT
DIGITAL
OUTPUT
DIGITAL
INPUT
BEAT
EFFECT
JOG
BREAK
SIGNAL FLOW sw.
EFX
LINK
9966kkHHzz2244--bbiittSSYYSSTTEEMM
27
Download from Www.Somanuals.com. All Manuals Search And Download.
|